Heiko Carstens [Tue, 8 May 2007 09:18:50 +0000 (11:18 +0200)]
[SCSI] zfcp: clear adapter failed flag if an fsf request times out.
Must clear adapter failed flag if an fsf request times out. This is
necessary because on link down situations the failed flags gets set
but the QDIO queues are still up. Since an adapter reopen will be
skipped if the failed flag is set an adapter_reopen that is issued
on fsf request timeout has no effect if the local link is down.
Might lead to locked up system if the SCSI stack is waiting for abort
completion.
Heiko Carstens [Tue, 8 May 2007 09:17:54 +0000 (11:17 +0200)]
[SCSI] zfcp: rework request ID management.
Simplify request ID management and make sure that frequently used
functions are inlined. Also fix a memory leak in zfcp_adapter_enqueue()
which only gets hit in error handling.
[SCSI] zfcp: Fix deadlock between zfcp ERP and SCSI
The SCSI stack requires low level drivers to register and
unregister devices. For zfcp this leads to the situation where
zfcp calls the SCSI stack, the SCSI tries to scan the new device
and the scan SCSI command fails. This would require the zfcp erp,
but the erp thread is already blocked in the register call.
The fix is to make sure that the calls from the ERP thread to
the SCSI stack do not block the ERP thread. In detail:
1) Use a workqueue to avoid blocking of the scsi_scan_target calls.
2) When removing a unit make sure that no scsi_scan_target call is
pending.
3) Replace scsi_flush_work with scsi_target_unblock. This avoids
blocking and has the same result.
There is a possible race condition while generating the unique
request ids and sequence numbers. Both might be read at the
same time and have the same value. Fix this by serializing the
access through the queue lock of the adapter: First call
zfcp_fsf_req_sbal_get that acquires the lock, then read and
increment the unique ids.
Brian King [Mon, 7 May 2007 22:09:05 +0000 (17:09 -0500)]
[SCSI] ipr: Use PCI-E reset API for new ipr adapter
Use a newly added PCI API to issue a PCI Fundamental reset
(warm reset) to a new ipr PCI-E adapter. Typically, the
ipr adapter uses the start BIST bit in config space to reset
an adapter. Issuing start BIST on this particular adapter
results in the PCI-E logic on the card losing sync, which
causes PCI-E errors, making the card unusable. The only reset
mechanism that exists on this hardware that does not have this
problem is PCI Fundamental reset (warm reset).
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
For each request that is sent to the FCP adapter, zfcp allocates
memory. Status information and data that is being read from the
device is written to this memory by the hardware. After that,
the hardware signals this via the response queue and zfcp
continues processing.
Now, if zfcp detects that there is a signal for an incoming
response from the hardware, but there is no outstanding request
for that request id, then some memory that can be in use anywhere
in the system has just been overwritten. This should never happen,
but if it does, stop the system with a panic.
Olaf Hering [Thu, 26 Apr 2007 07:35:19 +0000 (00:35 -0700)]
[SCSI] mesh: cleanup variable usage in interrupt handler
_ convert void* to struct mesh_state*
- remove unused irq argument from mesh_interrupt()
Signed-off-by: Olaf Hering <olaf@aepfle.de> Cc: James Bottomley <James.Bottomley@steeleye.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
walter harms [Thu, 26 Apr 2007 07:35:09 +0000 (00:35 -0700)]
[SCSI] megaraid: fix warnings when CONFIG_PROC_FS=n
drivers/scsi/megaraid.c: In function 'megaraid_probe_one':
drivers/scsi/megaraid.c:4893: warning: implicit declaration of function 'mega_create_proc_entry'
drivers/scsi/megaraid.c: In function 'megaraid_remove_one':
drivers/scsi/megaraid.c:4968: warning: unused variable 'buf'
Fix by adding #defines
Signed-off-by: walter harms <wharms@bfs.de> Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Salyzyn, Mark [Tue, 1 May 2007 15:43:06 +0000 (11:43 -0400)]
[SCSI] aacraid: superfluous adapter reset for IBM 8 series ServeRAID controllers
The kexec patch introduced a superfluous (and otherwise inert) reset of
some adapters. The register can have a hardware default value that has
zeros for the undefined interrupts. This patch refines the test of the
interrupt enable register to focus on only the interrupts that affect
the driver in order to detect if an incomplete shutdown of the Adapter
had occurred (kdump).
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Another layer on this onion also discovered by Duane, the
interrupt enable handler also needed to be set ... The interrupt enable
was called from within the synchronous command handler.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
cpu_to_le32 endianness conversions in tmscsim.c, followed by
arithmetic operations don't look correct. Besides, {in,out}[wl]
already perform the necessary conversions. Further, bus addresses
of request buffers are guaranteed to be (mapped) under 4G by
current scsi- and block-layer defaults. This could be explicitly
enforced by using blk_queue_bounce_limit(), which, however,
doesn't seem to be the common practice among SCSI drivers.
Signed-off-by: G. Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Brian King [Wed, 2 May 2007 15:44:11 +0000 (10:44 -0500)]
[SCSI] ipr: Better handle adapter boot time errors
If an ipr adapter encounters an adapter error requiring an
adapter reset to recover from prior to driver load time, the
error will be ignored and recovery will not happen until the
initial timeout occurs waiting for the firmware to come ready,
which means a five minute timeout. Fix is to read the interrupt
register before clearing any of the interrupts at probe time.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Now that we have the much better esp_scsi driver and low level drivers
are easy to port over deprecate the old NCR53C9x driver.
I've Cc'ed the m68k and mips lists because all but one bus glues are
for these platforms. Chances stand bad for the remaining driver,
mca_53c9x which hasn't gotten any non-trivial update since it was
merge in late 2.1.x and whos maintainers mail address bounces.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
James Smart [Fri, 27 Apr 2007 15:53:17 +0000 (11:53 -0400)]
[SCSI] fc_transport: make all rports wait dev_loss_tmo before removing them
Per the comment in the change - it's not always prudent to immediately
remove the rport upon first notice of a disconnect. Make all rports
wait dev_loss_tmo before being deleted (and each could have a separate
dev_loss_tmo value).
The original post was:
http://marc.info/?l=linux-scsi&m=117392196006703&w=2
The repost contains the following changes:
- Bug fix in fc_starget_delete(). Dev_loss_tmo_callbk() was called prior to
tearing down the target. The callback is to be the last thing called, as
it tells the LLDD that the rport is completely finished and can be torn
down. Rework so that terminate_rport_io() is called to terminate the
outstanding io. Isolated work so it's is simply "starget" work.
- Fix holes in original patch. There were code paths that did not expect
the dev_loss_tmo timer to be running for the non-fcp rports.
- Bug Fix: the transport wasn't protecting against a LLDD calling
fc_remote_port_delete() back-to-back. Thus, the dev_loss_tmo timer
could be restarted such that it fires after the rport had been deleted.
Validate rport state before starting the timer.
Signed-off-by: James Smart <James.Smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Brian King [Thu, 26 Apr 2007 21:00:12 +0000 (16:00 -0500)]
[SCSI] ipr: Handle IOA reset request
In ipr dual adapter configurations, the ipr adapter firmware
may require an adapter reset for various reasons. The reset
is requested by the adapter firmware logging an error with
an IOASC of 0x02048000. Add support to log this error, and
reset the adapter.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Brian King [Thu, 26 Apr 2007 21:00:10 +0000 (16:00 -0500)]
[SCSI] ipr: Handle check condition status from disk array device
On newer levels of microcode for ipr RAID adapters supporting
multi-initiator configurations, the disk array, or VSET, resources
are capable of generating a check condition. This patch prevents
ipr from generating sense data in this scenario and retrieving it
from the logical device instead.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Brian King [Thu, 26 Apr 2007 21:00:08 +0000 (16:00 -0500)]
[SCSI] ipr: Handle UA on disk array following an adapter reset
On certain ipr RAID adapters, which are capable of multi-initiator
configurations, the disk array, or VSET, resources will be in a POR
Unit Attention state following an adapter reset. In order for the
midlayer to handle the UA, I must report a bus reset to the logical
disk array bus at the end of an adapter reset.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Adrian Bunk [Thu, 26 Apr 2007 07:35:16 +0000 (00:35 -0700)]
[SCSI] qla4xxx: possible cleanups
- make needlessly global code static
- #if 0 unused functions
Signed-off-by: Adrian Bunk <bunk@stusta.de> Acked-by: Ravi Anand <ravi.anand@qlogic.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
James Smart [Wed, 25 Apr 2007 13:53:22 +0000 (09:53 -0400)]
[SCSI] lpfc 8.1.12 : Add support for async scanning
Add support for async scanning
Notes: This is the async scan patch to our driver from Matthew Wilcox.
The async scan logic is still subject to errors in insmod/rmmod, as
the async scan threads don't get shutdown when the module unloads
underneath them. See http://marc.info/?l=linux-scsi&m=117551999925582&w=2
Signed-off-by: James Smart <James.Smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
James Smart [Wed, 25 Apr 2007 13:52:34 +0000 (09:52 -0400)]
[SCSI] lpfc 8.1.12 : Round 2 of Miscellaneous fixes
Round 2 of Miscellaneous fixes:
- Ensure we don't prematurely re-enable IRQs in lpfc_sli_abort_fcp_cmpl().
- Prevent freeing of iocb after IOCB_TIMEDOUT error.
- Added code to cleanup REG_LOGIN mailbox command when a LOGO is received.
- Fix offline window where more work can sneak in after clearing work_ha
- Use target reset instead of LU reset in bus_device_reset_handler
- Fixed system hangs due to leaked host_lock.
- Fixed NULL pointer dereference during I/O with LIP.
- Fixed false iocb timeout.
- Fixed name server query response handling.
- Change rport dev_loss_tmo value when user change lpfc HBA's dev_loss_tmo.
- Fixed a memory leak in lpfc_sli_wake_mbox_wait.
- Fixed check for dropped frames.
- Removed hba queue depth calculation based on device PCI IDs
- Change min cr_count value specified in comment to agree with setting
Signed-off-by: James Smart <James.Smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
James Smart [Wed, 25 Apr 2007 13:51:38 +0000 (09:51 -0400)]
[SCSI] lpfc 8.1.12 : Modify ELS abort handling to prevent double completion
Modify ELS abort handling to prevent double completion
Rework portions of ELS abort handling to prevent double completion
- Rework ELS iotags and correct abort routine
- Move the (badly wrong) ELS completion logic from the initial ELS
abort request function to the ELS completion function.
- Fixup the iocb completion handling to account for the ELS abort
completions.
Signed-off-by: James Smart <James.Smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
James Smart [Wed, 25 Apr 2007 13:51:30 +0000 (09:51 -0400)]
[SCSI] lpfc 8.1.12 : Misc bug fixes and code cleanup
Misc bug fixes and code cleanup:
- Fix system hang while running on systems with IOMMU
- Fix use after free issues with rports
- Don't free mailbox structure if it's still on the mboxq list
- Decrement txq_cnt rather than txcmplq_cnt when parsing the txq list
- Use msleep for long delays to prevent soft lockup bug check
- Don't remove node during dev_loss_tmo if discovery is active
- Fix memory leaks in get/reset statistics and link attention paths
- Fixed lpfc_ns_rsp to handle entire GID_FT response.
- mbox interface should use MAILBOX_CMD_SIZE rather than sizeof(MAILBOX_t)
- Fixed bug check in add_timer.
- Fixup messages 0116, 0117, and 0128 to report ELS I/O tag.
- Remove unused parameter to lpfc_cleanup.
- Change mailbox timeout handling.
- Remove unused buflist. Code cleanup.
Signed-off-by: James Smart <James.Smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Brian King [Thu, 19 Apr 2007 18:59:59 +0000 (13:59 -0500)]
[SCSI] use sysfs configured timeout for EH Start Unit timeout
Use the sysfs configurable timeout when issuing a START_UNIT
command from the scsi error handler. This is needed for devices which
take longer than thirty seconds to respond to the start
unit. The problem was observed when sending a start unit
to a disk array device in an ipr RAID adapter, which results
in the adapter firmware sending potentially multiple commands
to physical devices as a result of this command, which ended
up timing out sometimes. This patch does not change the default
value used for this command.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Salyzyn, Mark [Mon, 16 Apr 2007 15:21:50 +0000 (11:21 -0400)]
[SCSI] aacraid: kmalloc/memset->kzalloc
Inspired somewhat by Vignesh Babu <vignesh.babu@wipro.com> patch to
dpt_i2o.c to replace kmalloc/memset sequences with kzalloc, doing the
same for the aacraid driver.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
[CIFS] Fix typo in cifs readme from previous commit
[CIFS] Make sec=none force an anonymous mount
[CIFS] Change semaphore to mutex for cifs lock_sem
[CIFS] Fix oops in reset_cifs_unix_caps on reconnect
[CIFS] UID/GID override on CIFS mounts to Samba
[CIFS] prefixpath mounts to servers supporting posix paths used wrong slash
[CIFS] Update cifs version to 1.49
[CIFS] Replace kmalloc/memset combination with kzalloc
[CIFS] Add IPv6 support
[CIFS] New CIFS POSIX mkdir performance improvement (part 2)
[CIFS] New CIFS POSIX mkdir performance improvement
[CIFS] Add write perm for usr to file on windows should remove r/o dos attr
[CIFS] Remove unnecessary parm to cifs_reopen_file
[CIFS] Switch cifsd to kthread_run from kernel_thread
[CIFS] Remove unnecessary checks
Linus Torvalds [Sat, 5 May 2007 21:55:20 +0000 (14:55 -0700)]
Merge branch 'for-linus' of git://one.firstfloor.org/home/andi/git/linux-2.6
* 'for-linus' of git://one.firstfloor.org/home/andi/git/linux-2.6: (231 commits)
[PATCH] i386: Don't delete cpu_devs data to identify different x86 types in late_initcall
[PATCH] i386: type may be unused
[PATCH] i386: Some additional chipset register values validation.
[PATCH] i386: Add missing !X86_PAE dependincy to the 2G/2G split.
[PATCH] x86-64: Don't exclude asm-offsets.c in Documentation/dontdiff
[PATCH] i386: avoid redundant preempt_disable in __unlazy_fpu
[PATCH] i386: white space fixes in i387.h
[PATCH] i386: Drop noisy e820 debugging printks
[PATCH] x86-64: Fix allnoconfig error in genapic_flat.c
[PATCH] x86-64: Shut up warnings for vfat compat ioctls on other file systems
[PATCH] x86-64: Share identical video.S between i386 and x86-64
[PATCH] x86-64: Remove CONFIG_REORDER
[PATCH] x86-64: Print type and size correctly for unknown compat ioctls
[PATCH] i386: Remove copy_*_user BUG_ONs for (size < 0)
[PATCH] i386: Little cleanups in smpboot.c
[PATCH] x86-64: Don't enable NUMA for a single node in K8 NUMA scanning
[PATCH] x86: Use RDTSCP for synchronous get_cycles if possible
[PATCH] i386: Add X86_FEATURE_RDTSCP
[PATCH] i386: Implement X86_FEATURE_SYNC_RDTSC on i386
[PATCH] i386: Implement alternative_io for i386
...
Fix up trivial conflict in include/linux/highmem.h manually.
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/voyager-2.6:
[VOYAGER] add smp alternatives
[VOYAGER] Use modern techniques to setup and teardown low identiy mappings.
[VOYAGER] Convert the monitor thread to use the kthread API
[VOYAGER] clockevents driver: bring voyager in to line
[VOYAGER] clockevents: correct boot cpu is zero assumption
[VOYAGER] add smp_call_function_single
This driver doesn't support SWDMA so use the correct ->swdma_mask.
While at it:
* no need to call config_chipset_for_pio() in config_chipset_for_dma(),
if DMA is not available config_chipset_for_pio() will be called
by siimage_config_drive_for_dma() and if DMA is available
config_siimage_chipset_for_pio() will be called by siimage_tune_chipset()
* limit max PIO mode to PIO4, this driver doesn't support PIO5 and attempt
to setup PIO5 by it821x_tuneproc() could result in incorrect PIO timings
+ incorrect base clock being set for controller in the passthrough mode
* move code limiting max PIO according to the pair device capabilities from
config_it821x_chipset_for_pio() to it821x_tuneproc() so the check is also
applied for mode change requests coming through ->tuneproc and ->speedproc
interfaces
* set device speed in it821x_tuneproc()
* in it821x_tune_chipset() call it821x_tuneproc() also if the controller is
in the smart mode (so the check for pair device max PIO is done)
* rename it821x_tuneproc() to it821x_tune_pio(), then add it821x_tuneproc()
wrapper which does the max PIO mode check; it worked by the pure luck
previously, pio[4] and pio_want[4] arrays were used with index == 255
so random PIO timings and base clock were set for the controller in the
passthrough mode, thankfully PIO timings and base clock were corrected
later by config_it821x_chipset_for_pio() call (but it was not called for
PIO-only devices during resume and for user requested PIO autotuning)
* remove config_it821x_chipset_for_pio() call from config_chipset_for_dma()
as the driver sets ->autotune to 1 and ->tuneproc does the proper job now
* convert the last user of config_it821x_chipset_for_pio() to use
it821x_tuneproc(drive, 255) and remove no longer needed function
Sergei Shtylyov [Sat, 5 May 2007 20:03:50 +0000 (22:03 +0200)]
aec62xx: fix PIO/DMA setup issues
Teach the driver's tuneproc() method to do PIO auto-runing properly since it
treated 5 instead of 255 as auto-tune request, and also passed the mode limit
of PIO5 to ide_get_best_pio_mode() despite supporting up to PIO4 only.
While at it, also:
- remove the driver's wrong claim about supporting SWDMA modes;
- stop hooking ide_dma_timeout() method as the handler clearly doesn't fit for
the task...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Sergei Shtylyov [Sat, 5 May 2007 20:03:50 +0000 (22:03 +0200)]
cmd64x: use interrupt status from MRDMODE register (take 2)
Fold the parts of the ide_dma_end() methods identical to __ide_dma_end() into a
mere call to it.
Start using faster versions of the ide_dma_end() and ide_dma_test_irq() methods
for the PCI0646U and newer chips that have the duplicate interrupt status bits
in the I/O mapped MRDMODE register, determing what methods to use at the driver
load time. Do some cleanup/renaming in the "old" ide_dma_test_irq() method too.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Sergei Shtylyov [Sat, 5 May 2007 20:03:50 +0000 (22:03 +0200)]
cmd64x: procfs code fixes/cleanups (take 2)
Fix several issues with the driver's procfs output:
- when testing if channel is enabled, the code looks at the "simplex" bits, not
at the real enable bits -- add #define for the primary channel enable bit;
- UltraDMA modes 0, 1, 3 for slave drive reported incorrectly due to using the
master drive's clock cycle resolution bit.
While at it, also perform the following cleanups:
- don't print extra newline before the first controller's dump;
- correct the chipset names (from CMDxxx to PCI-xxx)
- don't read from the registers which aren't used for dump;
- better align the table column sizes;
- rework UltraDMA mode dump code;
- remove PIO mode dump code that has never been finished;
- remove the duplicate interrupt status (the MRDMODE register bits mirror those
those in the CFR and ARTTIM23 registers) and fold the dump into single line;
- correct the style of the ?: operators...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Sergei Shtylyov [Sat, 5 May 2007 20:03:49 +0000 (22:03 +0200)]
cmd64x: add/fix enablebits (take 2)
The IDE core looks at the wrong bit when checking if the secondary channel is
enabled on PCI0646 -- CNTRL register bit 7 is read-ahead disable, bit 3 is the
correct one.
Starting with PCI0646U chip, the primary channel can also be enabled/disabled --
so, add 'enablebits' initializers to each 'ide_pci_device_t' structure, handling
the original PCI0646 via adding the init_setup() method and clearing the 'reg'
field there if necessary...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Sergei Shtylyov [Sat, 5 May 2007 20:03:49 +0000 (22:03 +0200)]
cmd64x: interrupt status fixes (take 2)
The driver's ide_dma_test_irq() method was reading the MRDMODE register even on
PCI0643/6 where it was write-only -- fix this by always reading the "backward-
compatible" interrupt bits, renaming dma_alt_stat to irq_stat as the interrupt
status bits are not coupled to DMA.
In addition, wrong interrupt bit was tested/cleared for the primary channel --
it's bit 2 in all the chip specs and the driver used bit 1... :-/
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Sergei Shtylyov [Sat, 5 May 2007 20:03:49 +0000 (22:03 +0200)]
cmd64x: fix multiword and remove single-word DMA support
Fix the multiword DMA and drop the single-word DMA support (which nobody will
miss, I think). In order to do it, a number of changes was necessary:
- rename program_drive_counts() to program_cycle_times(), pass to it cycle's
total/active times instead of the clock counts, and convert them into the
active/recovery clocks there instead of cmd64x_tune_pio() -- this causes
quantize_timing() to also move;
- contrarywise, move all the code handling the address setup timing into
cmd64x_tune_pio(), so that setting MWDMA mode wouldn't change address setup;
- remove from the speedproc() method the bogus code pretending to set the DMA
timings by twiddling bits in the BMIDE status register, handle setting MWDMA
by just calling program_cycle_times(); while at it, improve the style of that
whole switch statement;
- stop fiddling with the DMA capable bits in the speedproc() method -- they do
not enable DMA, and are properly dealt with by the dma_host_{on,off} methods;
- don't set hwif->swdma_mask in the init_hwif() method anymore.
In addition to those changes, do the following:
- in cmd64x_tune_pio(), when writing to ARTTIM23 register preserve the interrupt
status bit, eliminate local_irq_{save|restore}() around this code as there's
*no* actual race with the interrupt handler, and move cmdprintk() to a more
fitting place -- after ide_get_best_pio_mode() call;
- make {arttim|drwtim}_regs arrays single-dimensional, indexed with drive->dn;
- rename {setup|recovery}_counts[] into more fitting {setup|recovery}_values[];
- in the speedproc() method, get rid of the duplicate reads/writes from/to the
UDIDETCRx registers and of the extra variable used to store the transfer mode
value after filtering, use another method of determining master/slave drive,
and cleanup useless parens;
- beautify cmdprintk() output here and there.
While at it, remove meaningless comment about the driver being used only on
UltraSPARC and long non-relevant RCS tag. :-)
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Sergei Shtylyov [Sat, 5 May 2007 20:03:49 +0000 (22:03 +0200)]
sl82c105: DMA support code cleanup (take 4)
Fold the now equivalent code in the ide_dma_check() method into a mere call to
ide_use_dma(). Make config_for_dma() return non-zero if DMA mode has been set
and call it from the ide_dma_check() method instead of ide_dma_on().
Defer writing the DMA timings to the chip registers until DMA is really turned
on (and do not enable IORDY for DMA).
Remove unneeded code from the init_hwif() method, improve its overall looks.
Rename the dma_start(), ide_dma_check(), and ide_dma_lostirq() methods, and
also use more proper hwif->dma_command, fix printk() and comment in the latter
one as well. While at it, cleanup style in several places.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Sergei Shtylyov [Sat, 5 May 2007 20:03:49 +0000 (22:03 +0200)]
sl82c105: rework PIO support (take 2)
Get rid of the 'pio_speed' member of 'ide_drive_t' that was only used by this
driver by storing the PIO mode timings in the 'drive_data' instead -- this
allows us to greatly simplify the process of "reloading" of the chip's timing
register and do it right in sl82c150_dma_off_quietly() and to get rid of two
extra arguments to config_for_pio() -- which got renamed to sl82c105_tune_pio()
and now returns a PIO mode selected, with ide_config_drive_speed() call moved
into the tuneproc() method, now called sl82c105_tune_drive() with the code to
set drive's 'io_32bit' and 'unmask' flags in its turn moved to its proper place
in the init_hwif() method.
Also, while at it, rename get_timing_sl82c105() into get_pio_timings() and get
rid of the code in it clamping cycle counts to 32 which was both incorrect and
never executed anyway...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Matt Carlson [Sat, 5 May 2007 19:47:25 +0000 (12:47 -0700)]
[TG3]: Eliminate the TG3_FLAG_5701_REG_WRITE_BUG flag.
This patch removes the use of the TG3_FLAG_5701_REG_WRITE_BUG flag.
It's logic is only used to set a function pointer and thus the
logic can be collapsed and the flag removed.
[ Comment tidy by Christoph Hellwig. -DaveM ]
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com>
Michael Chan [Sat, 5 May 2007 19:10:20 +0000 (12:10 -0700)]
[TG3]: Remove reset during MAC address changes.
The reset was added a while back so that ASF could re-init whatever
MAC address it wanted to use after the MAC address was changed.
Instead of resetting, we can just keep MAC address 1 unchanged during
MAC address changes if MAC address 1 is different from MAC address 0.
This fixes 2 problems:
1. Bonding calls set_mac_address in contexts that cannot sleep.
It no longer sleeps with the chip reset removed.
2. When ASF shares the same MAC address as the NIC, it needs to
always do that even when the MAC address is changed.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Gary Zambrano [Sat, 5 May 2007 18:52:19 +0000 (11:52 -0700)]
[TG3]: WoL fixes.
Change TG3_FLAG_SERDES_WOL_CAP to TG3_FLAG_WOL_CAP to make it easier
to manage WoL. This flag is now used consistently during ethtool WoL
setup and power setting changes.
Signed-off-by: Gary Zambrano <zambrano@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Gary Zambrano [Sat, 5 May 2007 18:51:45 +0000 (11:51 -0700)]
[TG3]: Clear GPIO mask before storing.
The GPIO settings may change during reset and so the stored values in
tp->grc_local_ctrl should be cleared first.
Signed-off-by: Gary Zambrano <zambrano@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Sat, 5 May 2007 18:51:05 +0000 (11:51 -0700)]
[TG3]: Improve NVRAM sizing.
This patch changes the NVRAM sizing procedure so that the driver can
take advantage of devices with 1:1 NVRAM strapping configurations. This
is useful in cases where the traditional NVRAM sizing method fails. In
the event that the flash size cannot be determined, the largest known
NVRAM size is used. The patch also removes support for 5755 NVRAM
devices that are not supported by Broadcom and adds explicit sizing for
this device.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Sat, 5 May 2007 18:50:04 +0000 (11:50 -0700)]
[TG3]: Fix TSO bugs.
1. Remove the check for skb->len greater than MTU when doing TSO.
When the destination has a smaller MSS than the source, a TSO packet
may be smaller than the MTU and we still need to process it as a TSO
packet.
2. On 5705A3 devices with TSO enabled, the DMA engine can hang due to a
hardware bug. This patch avoids the hanging condition by reducing the
DMA burst size.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Sat, 5 May 2007 18:42:03 +0000 (11:42 -0700)]
[NETLINK]: Remove references to process ID
People treating the *_pid fields in netlink as a process ID has caused
endless confusion over the years. The fact that our own netlink.h
does this only adds to the confusion.
So here is a patch to change the comments to refer to it as the port
ID which hopefully will make it clear what the purpose of the fields
really is.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Heiko Carstens [Sat, 5 May 2007 18:41:18 +0000 (11:41 -0700)]
[AF_IUCV]: Compile fix - adopt to skbuff changes.
From: Heiko Carstens <heiko.carstens@de.ibm.com>
CC [M] net/iucv/af_iucv.o
net/iucv/af_iucv.c: In function `iucv_fragment_skb':
net/iucv/af_iucv.c:984: error: structure has no member named `h'
net/iucv/af_iucv.c:985: error: structure has no member named `nh'
net/iucv/af_iucv.c:988: error: incompatible type for argument 1 of
`skb_queue_tail'
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 5 May 2007 04:44:34 +0000 (21:44 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc: (46 commits)
mmc-omap: Clean up omap set_ios and make MMC_POWER_ON work
mmc-omap: Fix omap to use MMC_POWER_ON
mmc-omap: add missing '\n'
mmc: make tifm_sd_set_dma_data() static
mmc: remove old card states
mmc: support unsafe resume of cards
mmc: separate out reading EXT_CSD
mmc: break apart switch function
MMC: Fix handling of low-voltage cards
MMC: Consolidate voltage definitions
mmc: add bus handler
wbsd: check for data opcode earlier
mmc: Separate out protocol ops
mmc: Move core functions to subdir
mmc: deprecate mmc bus topology
mmc: remove card upon suspend
mmc: allow suspended block driver to be removed
mmc: Flush pending detects on host removal
mmc: Move host and card drivers to subdirs
mmc: Move queue functions to mmc_block
...
Linus Torvalds [Sat, 5 May 2007 03:44:54 +0000 (20:44 -0700)]
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2:
ocfs2: Force use of GFP_NOFS in ocfs2_write()
ocfs2: fix sparse warnings in fs/ocfs2/cluster
ocfs2: fix sparse warnings in fs/ocfs2/dlm
ocfs2: fix sparse warnings in fs/ocfs2
[PATCH] Copy i_flags to ocfs2 inode flags on write
[PATCH] ocfs2: use __set_current_state()
ocfs2: Wrap access of directory allocations with ip_alloc_sem.
[PATCH] fs/ocfs2/: make 3 functions static
ocfs2: Implement compat_ioctl()
Linus Torvalds [Sat, 5 May 2007 03:44:23 +0000 (20:44 -0700)]
iomap: make the default iomap functions fail softer
We used to BUG_ON() for a badly mapped IO port, which is certainly
correct, but actually made it harder to debug the case where the ATA
drivers had incorrectly mapped a nonconnected ATA port.
So make badly mapped ports trigger a WARN_ON(), and throw the IO away
instead (and return all ones for reads). For things like broken driver
initialization - which is the most likely cause anyway - that should
mean that the machine comes up and is usable (at least that was the case
for the ATA breakage that triggered this patch).
It tends to be a whole lot easier to do a "dmesg" on a working machine
than to try to capture logs off a dead one.
Jeff Layton [Sat, 5 May 2007 03:27:49 +0000 (03:27 +0000)]
[CIFS] Make sec=none force an anonymous mount
We had a customer report that attempting to make CIFS mount with a null
username (i.e. doing an anonymous mount) doesn't work. Looking through the
code, it looks like CIFS expects a NULL username from userspace in order
to trigger an anonymous mount. The mount.cifs code doesn't seem to ever
pass a null username to the kernel, however.
It looks also like the kernel can take a sec=none option, but it only seems
to look at it if the username is already NULL. This seems redundant and
effectively makes sec=none useless.
The following patch makes sec=none force an anonymous mount.
Linus Torvalds [Sat, 5 May 2007 02:55:11 +0000 (19:55 -0700)]
Merge git://git.linux-nfs.org/pub/linux/nfs-2.6
* git://git.linux-nfs.org/pub/linux/nfs-2.6: (28 commits)
NFS: Fix a compile glitch on 64-bit systems
NFS: Clean up nfs_create_request comments
spkm3: initialize hash
spkm3: remove bad kfree, unnecessary export
spkm3: fix spkm3's use of hmac
NFS4: invalidate cached acl on setacl
NFS: Fix directory caching problem - with test case and patch.
NFS: Set meaningful value for fattr->time_start in readdirplus results.
NFS: Added support to turn off the NFSv3 READDIRPLUS RPC.
SUNRPC: RPC client should retry with different versions of rpcbind
SUNRPC: remove old portmapper
NFS: switch NFSROOT to use new rpcbind client
SUNRPC: switch the RPC server to use the new rpcbind registration API
SUNRPC: switch socket-based RPC transports to use rpcbind
SUNRPC: introduce rpcbind: replacement for in-kernel portmapper
SUNRPC: Eliminate side effects from rpc_malloc
SUNRPC: RPC buffer size estimates are too large
NLM: Shrink the maximum request size of NLM4 requests
NFS: Use pgoff_t in structures and functions that pass page cache offsets
NFS: Clean up nfs_sync_mapping_wait()
...
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (49 commits)
[SCTP]: Set assoc_id correctly during INIT collision.
[SCTP]: Re-order SCTP initializations to avoid race with sctp_rcv()
[SCTP]: Fix the SO_REUSEADDR handling to be similar to TCP.
[SCTP]: Verify all destination ports in sctp_connectx.
[XFRM] SPD info TLV aggregation
[XFRM] SAD info TLV aggregationx
[AF_RXRPC]: Sort out MTU handling.
[AF_IUCV/IUCV] : Add missing section annotations
[AF_IUCV]: Implementation of a skb backlog queue
[NETLINK]: Remove bogus BUG_ON
[IPV6]: Some cleanups in include/net/ipv6.h
[TCP]: zero out rx_opt in tcp_disconnect()
[BNX2]: Fix TSO problem with small MSS.
[NET]: Rework dev_base via list_head (v3)
[TCP] Highspeed: Limited slow-start is nowadays in tcp_slow_start
[BNX2]: Update version and reldate.
[BNX2]: Print bus information for PCIE devices.
[BNX2]: Add 1-shot MSI handler for 5709.
[BNX2]: Restructure PHY event handling.
[BNX2]: Add indirect spinlock.
...
projects / linux-2.6 / log