Al Viro [Sun, 22 Jun 2008 17:20:49 +0000 (14:20 -0300)]
V4L/DVB (8126): net endianness fix
According to RFC 4326 (4.1) D-bit is MSB in net-endian 16bit.
dvb_net.c did
/* Set D-bit for CRC32 verification,
* if it was set originally. */
ulen |= 0x0080;
which works of little-endian (htons(1<<15) is 0x0080 there), but breaks
on big-endian.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
V4L/DVB (8123): Add support for em2860 based PointNix Intra-Oral Camera
em28xx-cards.c
em28xx-input.c
em28xx-video.c
em28xx.h
- Add support for the PointNix Intra-Oral Camera, which required addition of
a construct for reading the "snapshot" button (provided on the em2860 and
em2880 chips, but this is the first case where I have seen it actually used
in a product). The button is wired to pin 56 on the em2880.
http://www.pointnix.com/ENG/dental/product_02.asp
Thanks to Roberto Mantovani <rmantovani@libero.it> for testing the changes
Hans Verkuil [Wed, 25 Jun 2008 09:54:05 +0000 (06:54 -0300)]
V4L/DVB (8116): videodev: allow PRIVATE_BASE controls when called through VIDIOC_G/S_CTRL.
V4L2_CID_PRIVATE_BASE controls are not allowed when called from
VIDIOC_S/G_EXT_CTRL as extended controls use a better mechanism
for private controls. But still allow it when called from the
VIDIOC_G/S_CTRL to extended control conversion in video_ioctl2()
for backwards compatibility.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
cx18: Improved Raptor card audio input routing defintions, so that muxer values
matched cx18_gpio() values for tuner, line in 1, and radio and added LED
indication of selected audio input. Audio line in 2 doesn't work as it uses
the not yet supported 2nd I2S port. Tuner/FM Radio AF is mono until SIF
support is fixed.
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Hans Verkuil [Wed, 25 Jun 2008 09:29:01 +0000 (06:29 -0300)]
V4L/DVB (8112): videodev: improve extended control support in video_ioctl2()
- add sanity checks for the extended controls argument.
- if the driver only supports extended controls, then convert
old-style controls to an extended control callback.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- use %x rather than %d for control IDs and bitmask fields
- make two arrays const
- show the whole control array for the ext_ctrl ioctls
- print pix_fmt for V4L2_BUF_TYPE_VIDEO_OUTPUT
- show full type name rather than an integer
- fix CROPCAP debugging
- fix G/S_TUNER debugging
- show error code in case of an error
- other small cleanups
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Michael Krufky [Sun, 22 Jun 2008 01:13:42 +0000 (22:13 -0300)]
V4L/DVB (8098): xc5000: add module option to load firmware during driver attach
The xc5000 firmware download process can be slow on certain devices.
Add a module option, "init_fw" to perform the firmware download during
xc5000_attach(), which would get the firmware download over with well
before any tune request is made.
When this option is enabled, it will reduce the time it takes to get a
signal lock during the first tune after driver load, but will add a few
seconds to the driver initialization.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Ian Armstrong [Sat, 21 Jun 2008 14:09:46 +0000 (11:09 -0300)]
V4L/DVB (8090): ivtv: yuv decoder lock fix (2)
The IVTV_IOC_DMA_FRAME ioctl fails to correctly 'start' the decoder. Although
yuv output will be correct, some functions which should be disabled while the
decoder is in use remain enabled. This can result in hardware registers being
corrupted, causing problems with the mpeg decoder. This patch ensures the
decoder 'start' sequence is called, disabling these functions until the
device is closed.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Ian Armstrong [Sat, 21 Jun 2008 12:25:23 +0000 (09:25 -0300)]
V4L/DVB (8088): ivtv: yuv decoder lock fix
write() operations to the yuv device may not always 'start' the decoder.
Although yuv output will be correct, some functions which should be disabled
while the decoder is in use remain enabled. This can result in hardware
registers being corrupted, causing problems with the mpeg decoder. This patch
simply moves the existing decoder 'start' sequence to earlier in the write()
handler.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If the capture is scaled, then the video_temporal_filter is set to 0
by the cx2341x.c module since otherwise you would get ghosting.
However, this was also done in the VIDIOC_S_FMT ioctl which meant that
the video_temporal_filter control was reset to 0 or 8 each time S_FMT
was called. This was old code that should have been removed a long time
ago.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Andy Walls [Sat, 21 Jun 2008 11:36:31 +0000 (08:36 -0300)]
V4L/DVB (8082): cx18: convert to video_ioctl2()
cx18: convert driver to use video_ioctl2(). Pushed down ioctl debug
messages and priority checks as well. Still left serialization lock in
place for now. #if 0'ed out sliced vbi ioctl code for now.
Patch heavily based on similar changes made to ivtv by Hans Verkuil.
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
brandon@ifup.org [Sat, 21 Jun 2008 01:58:53 +0000 (22:58 -0300)]
V4L/DVB (8078): Introduce "index" attribute for persistent video4linux device nodes
A number of V4L drivers have a mod param to specify their preferred minors.
This is because it is often desirable for applications to have a static /dev
name for a particular device. However, using minors has several disadvantages:
1) the requested minor may already be taken
2) using a mod param is driver specific
3) it requires every driver to add a param
4) requires configuration by hand
This patch introduces an "index" attribute that when combined with udev rules
can create static device paths like this:
Michael Krufky [Tue, 17 Jun 2008 18:32:08 +0000 (15:32 -0300)]
V4L/DVB (8060): Kconfig: MEDIA_TUNER_CUSTOMIZE should be disabled by default
The build option, MEDIA_TUNER_CUSTOMIZE, allows us to disable tuner drivers
that would have otherwise been selected by default. This is an advanced
customization option that should be disabled by default.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Sigmund Augdal [Sun, 15 Jun 2008 20:25:46 +0000 (17:25 -0300)]
V4L/DVB (8049): budget-ci: Add support for Technotrend budget C-1501 dvb-c card
The following experimental patch adds support for the technotrend budget
C-1501 dvb-c card. The parameters used to configure the tda10023 demod
chip are largely determined experimentally, but works quite for me in my
initial tests.
Clean up the use of structure templates in bttv-i2c. For one thing, a
real template is supposed to be read-only. And in some cases it's more
efficient to initialize the few fields we need individually.
This clean-up shrinks bttv-i2c.o by 29% (x86_64).
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Clean up the use of structure templates in zoran_card. For one thing,
a real template is supposed to be read-only. And in some cases it's
more efficient to initialize the few fields we need individually.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Dmitry Belimov [Tue, 10 Jun 2008 17:22:00 +0000 (14:22 -0300)]
V4L/DVB (8021): Beholder's cards description
Split the Beholder M6 family to different models. Because M6 hasn`t RDS, M63
has chip with AC3 codec, M6 Extra has other type of HF module.
Add correct data for support MPEG encoder.
Dmitry Belimov [Tue, 10 Jun 2008 15:43:58 +0000 (12:43 -0300)]
V4L/DVB (8019): New for I2S on for MPEG of saa7134_empress
Rework saa7134_enable_i2s function. Remove vendor specific data.
Configure I2S output port specific for model of SAA7133/5-SAA7134.
I think it is more good.
Renamed definition of I2S audio output control register. It`s SAA7133/5 register
Start video port after configuring procedure.
V4L/DVB (8006): em28xx: Split HVR900 into two separate entries
- Separate the newer variant of the HVR-900 into its own device profile
because it has a Micronas DRX397 instead of the Zarlink demod. This
doesn't make the device work, but at least we don't try to initialize it
as though it had the Zarlink device.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
[mchehab@infradead.org: avoid compilation breakage at mainstream, where drx397xD.h doesn't exist yet] Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Tobias Lorenz [Sat, 31 May 2008 18:09:07 +0000 (15:09 -0300)]
V4L/DVB (7996): si470x: afc indication
This patch brings the following changes:
- afc indication:
device has no indication whether freq is too low or too high
therefore afc always return 1, when freq is wrong
Tobias Lorenz [Sat, 31 May 2008 18:07:52 +0000 (15:07 -0300)]
V4L/DVB (7995): si470x: a lot of small code cleanups
This patch brings the following changes:
- comment on how to listen to an usb audio device
(i get so many questions about that...)
- code cleanup (error handling, more warnings, spacing, ...)
Tobias Lorenz [Sat, 31 May 2008 18:04:32 +0000 (15:04 -0300)]
V4L/DVB (7993): si470x: move global lock to device structure
this patch brings the following changes:
- move the global disconnect lock into the device structure
- code cleanup (spaces to tabs, long line splits, ...)
Michael Krufky [Wed, 7 May 2008 04:43:10 +0000 (01:43 -0300)]
V4L/DVB (7986): cx23885: add initial support for DViCO FusionHDTV7 Dual Express
Only one frontend is enabled right now. The second frontend can lock,
but transport doesn't work yet. The device will be supported as a
single tuner device until the second frontend is working.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Antti Palosaari [Wed, 28 May 2008 06:57:39 +0000 (03:57 -0300)]
V4L/DVB (7952): AU6610: various cosmetic changes
- update license comments
- change MODULE_DESCRIPTION from device specific to chipset specific
- correct debug switch from deb_rc to deb_info
- correct MPEG2 stream interval from 1.25 to 1
- change frontend_attach error code from -EIO to -ENODEV
Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Hans Verkuil [Wed, 28 May 2008 15:16:41 +0000 (12:16 -0300)]
V4L/DVB (7949): videodev: renamed the vidioc_*_fmt_* callbacks
The naming for the callbacks that handle the VIDIOC_ENUM_FMT and
VIDIOC_S/G/TRY_FMT ioctls was very confusing. Renamed it to match
the v4l2_buf_type name.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Back in the early days of the pvrusb2 driver, the kernel class
mechanism in use for the sysfs interface had no means to pass
per-attribute information to the show / store functions. This forced
me to implement a horrible ugly thunking mechanism (i.e. infer the
missing data through the use of dedicated cookie cutter bounce
functions). However now we're using a better mechanism which also
passes enough additional information to the show / store functions
that we no longer need the hack. So eliminate all the crap. Yay!
Signed-off-by: Mike Isely <isely@pobox.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The driver enforces a "quiet period" on the encoder in certain
situations before attempting to operate it. This seems to help avoid
video encoding errors / corruption. The quiet period was 50msec, but
through experimentation it has been observed to improve further if the
interval is increased to 100msec.
Signed-off-by: Mike Isely <isely@pobox.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Hans Verkuil [Tue, 20 May 2008 09:24:04 +0000 (06:24 -0300)]
V4L/DVB (7927): ivtv: simplify gpio initialization for XCeive tuners.
Separate gpio_init field and xceive_pin and combine the two when
the gpio is initialized. So there is no longer any need to set the
xceive pin in the gpio_init values, simplifying the creation of a
new card definition.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Ian Armstrong [Mon, 12 May 2008 14:53:10 +0000 (11:53 -0300)]
V4L/DVB (7886): ivtvfb: Use DMA for write()
write() operations to the ivtv framebuffer will now attempt to use DMA if the
amount of data to copy is >= 4096 bytes. This change effectively depreciates
the need for the proprietary IVTVFB_IOC_DMA_FRAME ioctl since a write() of
sufficient size will do the same thing.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Michael Krufky [Sun, 11 May 2008 19:37:50 +0000 (16:37 -0300)]
V4L/DVB (7883): pvrusb2: make default frequency configurable via modprobe option
The pvrusb2 driver initially sets the tuner to known broadcast frequencies
in the Chicago area, to ease driver testing for the maintainer.
This patch keeps those default frequencies, but allows them to be altered
via modprobe option. This allows the same ease and convenience for testing
multiple pvrusb2 devices one after another under other conditions and areas.
For instance, the default initial frequency, 175.25 MHz, might not
necessarily be valid on all cable television networks, but usually will be a
valid NTSC broadcast channel.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mike Isely <isely@pobox.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2:
[PATCH] ocfs2: fix oops in mmap_truncate testing
configfs: call drop_link() to cleanup after create_link() failure
configfs: Allow ->make_item() and ->make_group() to return detailed errors.
configfs: Fix failing mkdir() making racing rmdir() fail
configfs: Fix deadlock with racing rmdir() and rename()
configfs: Make configfs_new_dirent() return error code instead of NULL
configfs: Protect configfs_dirent s_links list mutations
configfs: Introduce configfs_dirent_lock
ocfs2: Don't snprintf() without a format.
ocfs2: Fix CONFIG_OCFS2_DEBUG_FS #ifdefs
ocfs2/net: Silence build warnings on sparc64
ocfs2: Handle error during journal load
ocfs2: Silence an error message in ocfs2_file_aio_read()
ocfs2: use simple_read_from_buffer()
ocfs2: fix printk format warnings with OCFS2_FS_STATS=n
[PATCH 2/2] ocfs2: Instrument fs cluster locks
[PATCH 1/2] ocfs2: Add CONFIG_OCFS2_FS_STATS config option
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: fix asm/e820.h for userspace inclusion
x86: fix numaq_tsc_disable
x86: fix kernel_physical_mapping_init() for large x86 systems
Merge branch 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
ftrace: do not trace library functions
ftrace: do not trace scheduler functions
ftrace: fix lockup with MAXSMP
ftrace: fix merge buglet
make -C Documentation/lguest
cc -Wall -Wmissing-declarations -Wmissing-prototypes -O3 -I../../include
lguest.c -lz -o lguest
In file included from ../../include/asm-x86/bootparam.h:8,
from lguest.c:45:
../../include/asm/e820.h:66: error: expected ‘)’ before ‘start’
../../include/asm/e820.h:67: error: expected ‘)’ before ‘start’
../../include/asm/e820.h:68: error: expected ‘)’ before ‘start’
../../include/asm/e820.h:72: error: expected ‘=’, ‘,’, ‘;’, ‘asm’
or ‘__attribute__’ before ‘e820_update_range’
...
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Cc: Yinghai Lu <yhlu.kernel@gmail.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
projects / linux-2.6 / log