James Smart [Fri, 11 Jan 2008 06:53:18 +0000 (01:53 -0500)]
[SCSI] lpfc 8.2.4 : Fix Unsolicited Data items
Fix Drivers Unsolicited CT command handling - we did not handle multiframe
sequences well.
Fix error due to delay in replenishing buffers for unsolicited data.
Signed-off-by: James Smart <James.Smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch makes Emulex lpfc driver legacy I/O port free.
It has already been acked quite long time ago.
So I resubmit the patch.
http://lkml.org/lkml/2006/11/22/28
Current lpfc driver is already using pci_select_bars()
and pci_enable_device_bars() when the PCI bus has been reset.
So I think this patch should also be acked.
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@jp.fujitsu.com> Signed-off-by: James Smart <James.Smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
James Smart [Fri, 11 Jan 2008 06:52:54 +0000 (01:52 -0500)]
[SCSI] lpfc 8.2.4 : Miscellaneous Fixes
Miscellaneous Fixes:
- Fix a couple of sparse complaints
- Reset the FCP recovery flag when the node is not a FCP2 device.
- Speed up offline prep delays
- Fixed a memory leak in lpfc_mem_alloc failure path
- Fixed external loopback test.
- Fixed error code returned from the driver when HBA is over heated.
- Correct Max NPIV vport to limits read from adapter
- Add missing locks around fc_flag and FC_NEEDS_REG_VPI
- Add missing hba ids for device identification
- Added support for SET_VARIABLE and MBX_WRITE_WWN mailbox commands
- Changed all temperature event messages from warning to error
- Fix reporting of link speed when link is down
- Added support for MBX_WRITE_WWN mailbox command
- Change del_timer_sync() in ISR to del_timer() in interrupt handler
- Correct instances of beXX_to_cpu() that should be cpu_to_beXX()
- Perform target flush before releasing node references on module unload
- Avoid bogus devloss_tmo messages when driver unloads
- Fix panic when HBA generates ERATT interupt
- Fix mbox race condition and a workaround on back-to-back mailbox commands
- Force NPIV off for pt2pt mode between 2 NPorts
- Stop worker thread before removing fc_host.
- Fix up discovery timeout error case due to missing clear_la
- Tighten mailbox polling code to speed up detection of fast completions
- Only allow DUMP_MEMORY if adapter offline due to overtemp errors
- Added extended error information to the log messages in chip init.
Signed-off-by: James Smart <James.Smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Miscellaneous Discovery/ELS Fixes:
- Delay free's of ELS requests if adapter reject conditions
- Fix concurrent PLOGI vs ADISC state handling
- Add retry mechanism for GFF_ID
- Correct some illegal state transitions around RSCN timeouts
- Fix missing return in FAN handling
Signed-off-by: James Smart <James.Smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Salyzyn, Mark [Tue, 8 Jan 2008 22:07:57 +0000 (14:07 -0800)]
[SCSI] aacraid: improve queue balancing
The adapter queue is divided up equally to all the arrays to prevent
command starvation to any individual array. On the other hand,
physical targets are only granted a queue depth of one each. The code
prior to this patch used to deal with the incremental discovery of
targets, but the driver knows how many arrays are present prior to the
scan so this knowledge is used to generate a better estimate for the
queue depth.
Remove the capability of 'physical=0' from preventing access to the
class of adapters that have the RAID/SCSI mode of operation since none
of the physicals on the SCSI channel are candidates ever for an array.
As always, the user can override this default queue depth policy by
making the appropriate adjustments utilizing sysfs.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Salyzyn, Mark [Tue, 8 Jan 2008 21:26:43 +0000 (13:26 -0800)]
[SCSI] aacraid: OS panic after Adapter panic (hardening).
In experiments in the lab we managed to trigger an Adapter firmware
panic (BlinkLED) coincidentally while several pass-through ioctl
command from the management software were outstanding on a bug only
present on a class of RAID Adapters that require a hardware reset
rather than a commanded reset. The net result was an attempt to time
out the management software command as if it came from the SCSI layer
resulting in an OS panic.
Adapters that use commanded reset, management commands are returned
failed by the Adapter correctly. The adapter firmware panic that
resulted in this condition was also resolved, and there were no
adapters in the field with this specific firmware bug so we do not
expect any field reports. This is a rare or unlikely corner condition,
and no reports have ever been forwarded from the field.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Salyzyn, Mark [Tue, 8 Jan 2008 21:08:04 +0000 (13:08 -0800)]
[SCSI] aacraid: fix multiple definition of automatic variable warning.
The 'entry' automatic variable was defined at the top and within a
block that uses it, removed the definition from the block that uses
it. Some cosmetic changes were made while in the same file. This patch
should be inert.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Salyzyn, Mark [Tue, 8 Jan 2008 20:48:25 +0000 (12:48 -0800)]
[SCSI] aacraid: fix big endian issues
Big endian systems issues discovered in the aacraid driver. Somewhat
reverses a patch from November 7th of last year that removed swap
operations because they formerly were being assigned to an u8 array
when they should have been assigned to an le32 array.
This patch is largely inert for any little endian processor
architecture. It resolves a bug in delivering the BlinkLED AIF event
to registered applications when the adapter or associated hardware was
reset due to ill health. A rare corner case occurrence, also largely
unnoticed by any as it was a new (untested!) feature.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Salyzyn, Mark [Tue, 8 Jan 2008 20:01:07 +0000 (12:01 -0800)]
[SCSI] aacraid: add parameter to control FUA and SYNCHRONIZE_CACHE policy
aacraid.cache parameter, Disable Queue Flush commands:
bit 0 - Disable FUA in WRITE SCSI commands
bit 1 - Disable SYNCHRONIZE_CACHE SCSI command
bit 2 - Disable only if Battery not protecting adapter supplied Cache
e.g.: aacraid.cache=7 will disable the FUA and SYNCHRONIZE_CACHE
commands if the adapter has reported that it's cache is battery backed
up.
This parameter permits experimentation with tradeoffs between
performance and caching policy.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
James Bottomley [Sat, 5 Jan 2008 16:18:27 +0000 (10:18 -0600)]
[SCSI] scsi_transport_spi: convert to attribute groups
This conversion makes full use of the is_visible() callback on attribute
groups. Now, each device appears only with its capability flags in the
transport class directory. Previously each device appeared with the
capability of the host, so this is a functionality improvement.
Converting to attribute groups allows us to sweep away most of the home
grown #defines that were effectively doing the same thing.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
James Bottomley [Wed, 31 Oct 2007 14:38:04 +0000 (09:38 -0500)]
[SCSI] sysfs: add filter function to groups
This patch allows the various users of attribute_groups to selectively
allow the appearance of group attributes. The primary consumer of
this will be the transport classes in which we currently have
elaborate attribute selection algorithms to do this same thing.
Acked-by: Greg KH <greg@kroah.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
James Bottomley [Sat, 5 Jan 2008 15:38:30 +0000 (09:38 -0600)]
[SCSI] add missing transport configure points for target and host
While trying to convert the SPI transport class to attribute groups, I
discovered that we don't actually have any transport configure points
for either the target or the host. This patch adds these missing
transport class triggers. The host one is simply done after the add,
the target one tries to be more clever and add it after devices may have
been placed on the target (so the device configure will have set up the
target parameters).
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
James Bottomley [Thu, 3 Jan 2008 00:48:47 +0000 (18:48 -0600)]
[SCSI] attribute_container: update to use the group interface
This patch is the beginning of moving the attribute_containers to use
attribute groups exclusively. The attr element is now deprecated and
will eventually be removed (along with all the hand rolled code for
doing exactly what attribute groups do) when all the consumers are
converted to attribute groups.
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
James Bottomley [Thu, 3 Jan 2008 00:44:05 +0000 (18:44 -0600)]
[SCSI] sysfs: fix the sysfs_add_file_to_group interfaces
I can't see a reason why these shouldn't work on every group. However,
they only seem to work on named groups. This patch allows the group
functions to work on anonymous groups (those with NULL names).
Acked-by: Tejun Heo <htejun@gmail.com> Acked-by: Kay Sievers <kay.sievers@vrfy.org> Acked-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
James Bottomley [Tue, 22 Jan 2008 19:43:48 +0000 (13:43 -0600)]
[SCSI] libata: fix corruption induced by relaxed DMA alignment in SCSI
Hugh Dickens noticed that SMART commands issued from user space can
end up corupting memory. The problem occurs if the buffer used to
read data spans two pages. The reason is that the PIO sector routines
in libata are expecting physically contiguous pages when they do
sector operations, so the left overs on the second page go into the
next physically adjacent page rather than the next page in the sg
mapping.
Fix this by enforcing strict 512 byte alignment on all buffers from
userspace.
Acked-by: Hugh Dickins <hugh@veritas.com> Acked-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
James Bottomley [Tue, 1 Jan 2008 16:00:10 +0000 (10:00 -0600)]
[SCSI] relax scsi dma alignment
This patch relaxes the default SCSI DMA alignment from 512 bytes to 4
bytes. I remember from previous discussions that usb and firewire have
sector size alignment requirements, so I upped their alignments in the
respective slave allocs.
The reason for doing this is so that we don't get such a huge amount of
copy overhead in bio_copy_user() for udev. (basically all inquiries it
issues can now be directly mapped).
Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
James Bottomley [Mon, 31 Dec 2007 22:37:00 +0000 (16:37 -0600)]
[SCSI] block: Introduce new blk_queue_update_dma_alignment interface
The purpose of this is to allow stacked alignment settings, with the
ultimate queue alignment being set to the largest alignment requirement
in the stack.
The reason for this is so that the SCSI mid-layer can relax the default
alignment requirements (which are basically causing a lot of superfluous
copying to go on in the SG_IO interface) while allowing transports,
devices or HBAs to add stricter limits if they need them.
Acked-by: Jens Axboe <jens.axboe@oracle.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
James Bottomley [Sun, 30 Dec 2007 18:37:31 +0000 (12:37 -0600)]
[SCSI] libsas: don't use made up error codes
This is bad for two reasons:
1. If they're returned to outside applications, no-one knows what
they mean.
2. Eventually they'll clash with the ever expanding standard error
codes.
The problem error code in question is ETASK. I've replaced this by
ECOMM (communications error on send) a network error code that seems to
most closely relay what ETASK meant.
Acked-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
James Bottomley [Sat, 29 Dec 2007 16:59:53 +0000 (10:59 -0600)]
[SCSI] libsas, bsg: pass errors through correctly
Currently in BSG, errors returned in req->errors aren't passed back to
the calling programme (either via SG_IO or via read/write). Fix this,
while preserving the SCSI convention of returning status in
req->errors.
Now update libsas to return errors correctly instead of to ignore
them.
Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
James Bottomley [Sat, 29 Dec 2007 17:49:53 +0000 (11:49 -0600)]
[SCSI] libsas: don't treat underrun as an error on SMP tasks
All SMP tasks sent through bsg generate messages like:
sas: smp_execute_task: task to dev 500605b000001450 response: 0x0 status 0x81
Three times (because the task gets retried). Firstly, don't retry
either overrun or underrun (the data buffer isn't going to change size)
and secondly, just report the underrun but don't set an error for it.
This is necessary so bsg can report back the residual.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Christof Schmitt [Thu, 20 Dec 2007 11:30:27 +0000 (12:30 +0100)]
[SCSI] zfcp: Hold queue lock when checking port/unit handle for task management cmd
We need to hold the queue-lock when checking whether we still have a valid
unit/port handle for the task management command, i.e whether we can issue this
request for this unit/port. If the error recovery is about to close this
unit/port, then it competes for the queue-lock. If the close request issued by
the error recovery wins, then it is guaranteed that this unit/port has been
blocked for other requests.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com> Signed-off-by: Martin Peschke <mp3@de.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Christof Schmitt [Thu, 20 Dec 2007 11:30:26 +0000 (12:30 +0100)]
[SCSI] zfcp: Hold queue lock when checking port/unit handle for FCP command
We need to hold the queue-lock when checking whether we still have a valid
unit/port handle for the FCP command, i.e whether we can issue this request for
this unit/port. If the error recovery is about to close this unit/port, then it
competes for the queue-lock. If the close request issued by the error recovery
wins, then it is guaranteed that this unit/port has been blocked for other
requests.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com> Signed-off-by: Martin Peschke <mp3@de.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Christof Schmitt [Thu, 20 Dec 2007 11:30:25 +0000 (12:30 +0100)]
[SCSI] zfcp: Hold queue lock when checking port handle for ELS command
We need to hold the queue-lock when checking whether we still have a valid port
handle for the ELS command, i.e whether we can issue this request for this
port. If the error recovery is about to close this port, then it competes for
the queue-lock. If the close request issued by the error recovery wins, then it
is guaranteed that this port has been blocked for other requests.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com> Signed-off-by: Martin Peschke <mp3@de.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Christof Schmitt [Thu, 20 Dec 2007 11:30:24 +0000 (12:30 +0100)]
[SCSI] zfcp: Hold queue lock when checking port/unit handle for abort command
We need to hold the queue-lock when checking whether we still have a valid
unit/port handle for the abort command, i.e whether we can issue this request
for this unit/port. If the error recovery is about to close this unit/port,
then it competes for the queue-lock. If the close request issued by the error
recovery wins, then it is guaranteed that this unit/port has been blocked for
other requests.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com> Signed-off-by: Martin Peschke <mp3@de.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Christof Schmitt [Thu, 20 Dec 2007 11:30:23 +0000 (12:30 +0100)]
[SCSI] zfcp: Fix evaluation of port handles in abort handler
According to the FSF spec, word 0 (bytes 0-3) has the handle
specified with the abort command and word 1 (bytes 4-7) has the
handle for the command to be aborted. Fix the if statements
that try to compare those.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com> Signed-off-by: Martin Peschke <mp3@de.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Heiko Carstens [Thu, 20 Dec 2007 11:30:22 +0000 (12:30 +0100)]
[SCSI] zfcp: fix use after free bug.
zfcp_erp_strategy_check_fsfreq() checks if it is safe to access the
fsf_req associated with the erp_action that gets passed. To test if
it is safe it accesses the fsf_req in order to get its index into
the hash list. This is broken since the fsf_req might be freed already
and the read index has no meaning. It could lead to memory corruption.
Fix this by introducing a new zfcp_reqlist_find_safe() method which
just checks if addresses are equal. This is slower, but only gets
called in case of error recovery.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com> Signed-off-by: Martin Peschke <mp3@de.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Swen Schillig [Tue, 18 Dec 2007 10:16:14 +0000 (11:16 +0100)]
[SCSI] zfcp: update MAINTAINERS
we are planning a major rewrite of the zfcp driver,
meaning that a lot of patches will hit the mailing-list in the near future.
Since I can't support this additional work-load along with my other
responsibilities we are shifting the maintainership to
Christof Schmitt as the maintainer and
Martin Peschke as the co-maintainer.
Please support the two in providing us a new and more stable
zfcp environment.
Thanks
Swen
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Mike Christie [Thu, 13 Dec 2007 18:43:42 +0000 (12:43 -0600)]
[SCSI] iscsi_tcp: fix setting of r2t
If we negotiate for X r2ts we have to use only X r2ts. We cannot
round up (we could send less though). It is ok to fail if it
is not something the driver can handle, so this patch just does
that.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Mike Christie [Thu, 13 Dec 2007 18:43:39 +0000 (12:43 -0600)]
[SCSI] iscsi_tcp: enable sg chaining
The previous patches converted iscsi_tcp to support sg chaining.
This patch sets the proper flags and sets sg_table size to
4096. This allows fs io to be capped at max_sectors, but passthrough
IO to be limited by some other part of the kernel.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Mike Christie [Thu, 13 Dec 2007 18:43:37 +0000 (12:43 -0600)]
[SCSI] iscsi_tcp: drop session when itt does not match any command
A target should never send us a itt that does not match a running
task. If it does we do not really know what is coming down after the header,
unless we evaluate the hdr and do some guessing sometimes. However,
even if we know what is coming we probably do not have buffers for it or we
cannot respond (if it is a r2t for example), so just drop the session.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Olaf Kirch [Thu, 13 Dec 2007 18:43:36 +0000 (12:43 -0600)]
[SCSI] iscsi_tcp: stop leaking r2t_info's when the incoming R2T is bad
iscsi_r2t_rsp checks the incoming R2T for sanity, and if it
thinks it's fishy, it will drop it silently. In this case, we
leaked an r2t_info object. If we do this often enough, we run
into a BUG_ON some time later.
Removed r2t wrappers and update patch by Mike Christie
Signed-off-by: Olaf Kirch <olaf.kirch@oracle.com> Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Olaf Kirch [Thu, 13 Dec 2007 18:43:35 +0000 (12:43 -0600)]
[SCSI] iscsi: convert xmit path to iscsi chunks
Convert xmit to iscsi chunks.
from michaelc@cs.wisc.edu:
Bug fixes, more digest integration, sg chaining conversion and other
sg wrapper changes, coding style sync up, and removal of io fields,
like pdu_sent, that are not needed.
Signed-off-by: Olaf Kirch <olaf.kirch@oracle.com> Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Mike Christie [Thu, 13 Dec 2007 18:43:33 +0000 (12:43 -0600)]
[SCSI] libiscsi: clear conn->ctask when task is completed early
If the current ctask is failed early, we legt the conn->ctask pointer
pointing to a invalid task. When the xmit thread would send data for
it, we would then oops.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Mike Christie [Thu, 13 Dec 2007 18:43:32 +0000 (12:43 -0600)]
[SCSI] libiscsi: Do not fail commands immediately during logout
If the target requests a logout, then we do not want
to fail commands to scsi-ml right away. This patch just
fails in pending commands for a requeue immediately, and then lets
iscsid handle running commands like normal recovery.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Mike Christie [Thu, 13 Dec 2007 18:43:30 +0000 (12:43 -0600)]
[SCSI] libiscsi: fix nop handling
During root boot and shutdown the target could send us nops.
At this time iscsid cannot be running, so the target will drop
the session and the boot or shutdown will hang.
To handle this and allow us to better control when to check the network
this patch moves the nop handling to the kernel.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Mike Christie [Thu, 13 Dec 2007 18:43:29 +0000 (12:43 -0600)]
[SCSI] libiscsi: fix shutdown
We were using the device delete sysfs file to remove each device
then logout. Now in 2.6.21 this will not work because
the sysfs delete file returns immediately and does not wait for
the device removal to complete. This causes a hang if a cache sync
is needed during shutdown. Before .21, that approach had other
problems, so this patch fixes the shutdown code so that we remove the target
and unbind the session before logging out and shut down the session
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Mike Christie [Thu, 13 Dec 2007 18:43:28 +0000 (12:43 -0600)]
[SCSI] libiscsi: grab eh_mutex during host reset
I thought we may not need the eh mutex during host reset, but that is wrong
with the new shutdown code. When start_session_recovery sets the state to
terminate then drops the session lock. The scsi eh thread could then grab the
session lock see that we are terminating and then return failed to scsi-ml.
scsi-ml's eh then owns the command and will do whatever it wants
with it. But then the iscsi eh thread could grab the session lock
and want to complete the scsi commands that we in the LLD, but
it no longer owns them and kaboom.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Mike Christie [Thu, 13 Dec 2007 18:43:27 +0000 (12:43 -0600)]
[SCSI] iscsi class: Use our own workq instead of common system one.
There is just too much going on through the common workq and
something like a scsi device removal through sysfs affects
how long it will take to recover the transport, mark it as
failed, or shut it down gracefully.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Olaf Kirch [Thu, 13 Dec 2007 18:43:25 +0000 (12:43 -0600)]
[SCSI] libiscsi, iscsi_tcp: iscsi pool cleanup
iscsi_pool_init simplified
iscsi_pool_init currently has a lot of duplicate kfree() calls it does
when some allocation fails. This patch simplifies the code a little by
using iscsi_pool_free to tear down the pool in case of an error.
iscsi_pool_init also returns a copy of the item array to the caller.
Not all callers use this array, so we make it optional.
Instead of allocating a second array and return that, allocate just one
array, of twice the size.
Update users of iscsi_pool_{init,free}
This patch drops the (now useless) second argument to
iscsi_pool_free, and updates all callers.
It also removes the ctask->r2ts array, which was never
used anyway. Since the items argument to iscsi_pool_init
is now optional, we can pass NULL instead.
Signed-off-by: Olaf Kirch <olaf.kirch@oracle.com> Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Boaz Harrosh [Thu, 13 Dec 2007 18:43:24 +0000 (12:43 -0600)]
[SCSI] libiscsi,iser: patch for AHS support
- The default initialization of hdr_max is the minimum -
sizeof(struct iscsi_cmd) - Once this patch goes into iser the default
initialization at libiscsi can be removed.
- This is not yet full support for AHSs at iser end. But it should be easy.
Just allocate more space at iser_desc right after iscsi_hdr. Than
at transmission time use ctask->hdr_len to retrieve the total
size of all iscsi pdu headers. See previous patch at iscsi_tcp.[ch]
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com> Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Boaz Harrosh [Thu, 13 Dec 2007 18:43:23 +0000 (12:43 -0600)]
[SCSI] iscsi_tcp, libiscsi: initial AHS Support
at libiscsi generic code
- currently code assumes a storage space of pdu header is allocated
at llds ctask and is pointed to by iscsi_cmd_task->hdr. Here I add
a hdr_max field pertaining to that storage, and an hdr_len that
accumulates the current use of the pdu-header.
- Add an iscsi_next_hdr() inline which returns the next free space
to write new Header at. Also iscsi_next_hdr() is used to retrieve
the address at which to write the header-digest.
- Add iscsi_add_hdr(length). What the user do is calls iscsi_next_hdr()
for address of the new header, than calls iscsi_add_hdr(length) with
the size of the new header. iscsi_add_hdr() will check if space is
available and update to the new size. length must be padded according
to standard.
- Add 2 padding inline helpers thanks to Olaf. Current patch does not
use them but Following patches will.
Also moved definition of ISCSI_PAD_LEN to iscsi_proto.h which had
PAD_WORD_LEN that was never used anywhere.
- Let iscsi_prep_scsi_cmd_pdu() signal an Error return since now it is
possible that it will fail.
- I was tired of yet again writing a "this is a digest" comment next to
sizeof(__u32) so I defined a new ISCSI_DIGEST_SIZE. Now I don't need
any comments. Changed all places that used sizeof(__u32) or "4" in
connection to a digest.
iscsi_tcp specific code
- At struct iscsi_tcp_cmd_task allocate maximum space allowed in
standard for all headers following the iscsi_cmd header. and mark
it so in iscsi_tcp_session_create()
- At iscsi_send_cmd_hdr() retrieve the correct headers size and
write header digest at iscsi_next_hdr().
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com> Signed-off-by: Olaf Kirch <olaf.kirch@oracle.com> Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Boaz Harrosh [Thu, 13 Dec 2007 18:43:22 +0000 (12:43 -0600)]
[SCSI] iscsi: Prettify resid handling and some extra checks
- Check to see that OVERFLOW is not negative indicating
a bug.
- Unify handling of UNDERFLOW and OVERFLOW to the same
code.
- Also handle BIDI_OVERFLOW.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com> Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Olaf Kirch [Thu, 13 Dec 2007 18:43:21 +0000 (12:43 -0600)]
[SCSI] iscsi_tcp: rewrite recv path
Rewrite recv path. Fixes:
- data digest processing and error handling.
- ahs support.
Some fixups by Mike Christie
Signed-off-by: Olaf Kirch <olaf.kirch@oracle.com> Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Denis Cheng [Fri, 14 Dec 2007 00:14:27 +0000 (16:14 -0800)]
[SCSI] ipr: use LIST_HEAD instead of LIST_HEAD_INIT
Signed-off-by: Denis Cheng <crquan@gmail.com> Acked-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Jeff Garzik [Fri, 14 Dec 2007 00:14:13 +0000 (16:14 -0800)]
[SCSI] sym53c416: kill pointless irq handler loop and test
- kill pointless irq handler loop to find base address, it is already
passed to irq handler via Scsi_Host.
- kill now-pointless !base test.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Jeff Garzik [Fri, 14 Dec 2007 00:14:14 +0000 (16:14 -0800)]
[SCSI] NCR5380: minor irq handler cleanups
* remove unnecessary cast
* remove unnecessary use of 'irq' function arg
Signed-off-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
As reported in http://bugzilla.kernel.org/show_bug.cgi?id=3D9133 it was
discovered that the PERC line of controllers lacked a key 64 bit
ScatterGather capable SCSI pass-through function. The adapters are still
capable of 64 bit ScatterGather I/O commands, but these two can not be
mixed. This problem was exacerbated by the introduction of the SCSI
Generic access to the DASD physical devices.
The fix for users before this patch is applied is aacraid.dacmode=3D0 on
the kernel command line to disable 64 bit I/O.
The enclosed patch introduces a new adapter quirk and tries to limp
along by enabling pass-through in situations where memory is 32 bit
addressable on 64 bit machines, or disable the pass-through functions
altogether. I expect that the check for 32 bit addressable memory to be
controversial in that it can be incorrect in non-Dell non-Intel systems
that PERC would never be installed under, the alternative is to disable
pass-through in all cases which could be reported as another regression.
Pass-through is used for SCSI Generic access to the physical devices, or
for the management applications to properly function.
In systems where this patch has disabled pass-through because it is
unsupportable in combination with I/O performance, the user can choose
to enable pass-through by turning off dacmode (aacraid.dacmode=3D0) or
limiting the discovered kernel memory (mem=3D4G) with an associated loss
in runtime performance. If we chose instead to turn off 64 bit dacmode
for the adapters with this quirk, then this would be reported as another
regression.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
[SCSI] hptiop: add more adapter models and other fixes
Most code changes were made to support adapters based on Marvell IOP, plus some
other fixes.
- add more PCI device IDs
- support for adapters based on Marvell IOP
- fix a result code translation error on big-endian systems
- fix resource releasing bug when scsi_host_alloc() fail in hptiop_probe()
- update scsi_cmnd.resid when finishing a request
- correct some coding style issues
[akpm@linux-foundation.org: type fixes] Signed-off-by: HighPoint Linux Team <linux@highpoint-tech.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Adrian Bunk [Mon, 5 Nov 2007 17:07:33 +0000 (18:07 +0100)]
[SCSI] lpfc: minor cleanups
This patch contains the following minor cleanups:
- make the following needlessly global functions static:
- lpfc_els.c: lpfc_register_new_vport()
- lpfc_els.c: lpfc_issue_els_fdisc()
- lpfc_els.c: lpfc_issue_fabric_iocb()
- lpfc_els.c: lpfc_fabric_abort_vport()
- lpfc_hbadisc.c: lpfc_dev_loss_tmo_handler()
- lpfc_hbadisc.c: lpfc_mbx_cmpl_clear_la()
- lpfc_hbadisc.c: lpfc_disc_flush_list()
- lpfc_hbadisc.c: __lpfc_find_node()
- lpfc_init.c: lpfc_hb_timeout()
- lpfc_init.c: lpfc_block_mgmt_io()
- lpfc_sli.c: __lpfc_sli_release_iocbq()
- lpfc_sli.c: lpfc_sli_next_hbq_slot()
- lpfc_sli.c: lpfc_sli_hbqbuf_init_hbqs()
- lpfc_sli.c: lpfc_sli_hbqbuf_find()
- lpfc_sli.c: __lpfc_sli_issue_iocb()
- #if 0 the following unused global functions:
- lpfc_els.c: lpfc_fabric_abort_flogi()
- lpfc_hbadisc.c: lpfc_find_node()
- lpfc_hbadisc.c: lpfc_findnode_rpi()
- remove the unused exports
Signed-off-by: Adrian Bunk <bunk@kernel.org> Acked-by: James Smart <James.Smart@Emulex.Com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
James Bottomley [Sun, 2 Dec 2007 17:10:40 +0000 (19:10 +0200)]
[SCSI] sd,sr: add early detection of medium not present
The current scsi_test_unit_ready() is updated to return sense code
information (in struct scsi_sense_hdr). The sd and sr drivers are
changed to interpret the sense code return asc 0x3a as no media and
adjust the device status accordingly.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Randy Dunlap [Thu, 15 Nov 2007 09:53:25 +0000 (11:53 +0200)]
[SCSI] tgt: fix build when dprintk is defined
Fix scsi_tgt_lib build when dprintk is defined:
Also fix accessors problem when dprintk is defined
drivers/scsi/scsi_tgt_lib.c: In function 'scsi_tgt_cmd_destroy':
drivers/scsi/scsi_tgt_lib.c:183: warning: format '%lu' expects type 'long unsigned int', but argument 6 has type 'unsigned int'
drivers/scsi/scsi_tgt_lib.c: In function 'scsi_tgt_cmd_done':
drivers/scsi/scsi_tgt_lib.c:330: warning: format '%lu' expects type 'long unsigned int', but argument 5 has type 'unsigned int'
drivers/scsi/scsi_tgt_lib.c: In function 'scsi_tgt_transfer_response':
drivers/scsi/scsi_tgt_lib.c:345: warning: format '%lu' expects type 'long unsigned int', but argument 5 has type 'unsigned int'
drivers/scsi/scsi_tgt_lib.c: In function 'scsi_tgt_init_cmd':
drivers/scsi/scsi_tgt_lib.c:368: warning: format '%lu' expects type 'long unsigned int', but argument 6 has type 'unsigned int'
drivers/scsi/scsi_tgt_lib.c: In function 'scsi_tgt_kspace_exec':
drivers/scsi/scsi_tgt_lib.c:499: warning: format '%lu' expects type 'long unsigned int', but argument 9 has type 'unsigned int'
drivers/scsi/scsi_tgt_lib.c: In function 'scsi_tgt_kspace_it_nexus_rsp':
drivers/scsi/scsi_tgt_lib.c:620: error: 'mid' undeclared (first use in this function)
drivers/scsi/scsi_tgt_lib.c:620: error: (Each undeclared identifier is reported only once
drivers/scsi/scsi_tgt_lib.c:620: error: for each function it appears in.)
make[2]: *** [drivers/scsi/scsi_tgt_lib.o] Error 1
[SCSI] aacraid: don't assign cpu_to_le32(int) to u8
On Wed, Nov 07, 2007 at 01:51:44PM -0500, Salyzyn, Mark wrote:
> Christoph Hellwig [mailto:hch@infradead.org] sez:
> > Did anyone run the driver through sparse to see if we have
> > more issues like this?
>
> There are some warnings from sparse, none like this one. I will deal
> with the warnings ...
Actually there are a lot of endianess warnings, fortunately most of them
harmless. The patch below fixes all of them up (including the ones in
the patch I replied to), except for aac_init_adapter which is really odd
and I don't know what to do.
[jejb fixed up rejections and checkpatch issues]
Signed-off-by: Christoph Hellwig <hch@lst.de> Acked-by: Mark Salyzyn <mark_salyzyn@adaptec.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Drivers do SCRs for each Vport. When something changes in the
fabric, firmware generates one interrupt for each RSCN. Based on
the current implementation, in each case, we make recursive calls
to handle RSCN for physical and each subsequent virtual ports.
The fix is to also take into consideration the vp_idx, which is
set by the firmware to indicate the vport the RSCN was meant for.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Andrew Vasquez [Mon, 12 Nov 2007 18:30:58 +0000 (10:30 -0800)]
[SCSI] qla2xxx: Correct NPIV support for recent ISPs.
Firmware will export to software the maximum number of vports
supported for any given firmware version and ISP type. Use this
information rather than the current hardcoding of limitations
within the driver.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Andrew Vasquez [Mon, 12 Nov 2007 18:30:57 +0000 (10:30 -0800)]
[SCSI] qla2xxx: Don't explicitly read mbx registers while processing a system-error.
Callers of qla2x00_async_event() already populate the mb[] array
upon invocation, doing so via the appropriate mailbox register
accessors. The stale codes removed are leftover-bits kept during
the FWI2 transition. Though relatively benign, the extra-reads
are not valid for FWI2 boards (ISP24xx and above) and peek into
the incorrect regions of registers.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Robert Jennings [Mon, 12 Nov 2007 15:00:23 +0000 (09:00 -0600)]
[SCSI] ibmvscsi: requeue while CRQ closed
CRQ send errors that return with H_CLOSED should return with
SCSI_MLQUEUE_HOST_BUSY until firmware alerts the client of a CRQ
transport event. The transport event will either reinitialize and
requeue the requests or fail and return IO with DID_ERROR.
To avoid failing the eh_* functions while re-attaching to the server
adapter this will retry for a period of time while ibmvscsi_send_srp_event
returns SCSI_MLQUEUE_HOST_BUSY.
In ibmvscsi_eh_abort_handler() the loop includes the search of the
event list. The lock on the hostdata is dropped while waiting to try
again after failing ibmvscsi_send_srp_event. The event could have been
purged if a login was in progress when the function was called.
In ibmvscsi_eh_device_reset_handler() the loop includes the call to
get_event_struct() because a failing call to ibmvscsi_send_srp_event()
will have freed the event struct.
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com> Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Randy Dunlap [Thu, 15 Nov 2007 23:42:30 +0000 (15:42 -0800)]
[SCSI] docbook and kernel-doc updates
- Change title to remove "Mid-Layer" since the doc is about all of the
SCSI layers.
- Use "SCSI" instead of "scsi" in docbook text.
- Use "*/" to end kernel-doc notation blocks.
- A few other minor typo fixes.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Randy Dunlap [Thu, 15 Nov 2007 00:52:25 +0000 (16:52 -0800)]
[SCSI] boot options: correct option name and tell where to find docs for it
Minor corrections and additions to 'scsi_logging_level', as pointed out
by Chuck Ebbert.
Also point out the IBM S390-tools 'scsi_logging_level' script.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tony Battersby [Mon, 12 Nov 2007 15:00:44 +0000 (10:00 -0500)]
[SCSI] move single_lun flag from scsi_device to scsi_target
Some SCSI tape medium changers that need the BLIST_SINGLELUN flag have
the medium changer at one LUN and the tape drive at a different LUN.
The inquiry string of the tape drive may be different from that of the
medium changer. In order for single_lun to be effective, every
scsi_device under a given scsi_target must have it set. This means that
there needs to be a blacklist entry for BOTH the medium changer AND the
tape drive, which is impractical because some medium changers may be
paired with a variety of different tape drive models. It makes more
sense to put the single_lun flag in scsi_target instead of scsi_device,
which causes every device at a given target ID to inherit the single_lun
flag from one LUN. This makes it possible to blacklist just the medium
changer and not the tape drive.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
bo yang [Fri, 9 Nov 2007 09:40:16 +0000 (04:40 -0500)]
[SCSI] megaraid_sas: support for poll_mode_io (reduced interrupt)
Added module parameter "poll_mode_io" to support for "polling"
(reduced interrupt operation). In this mode, IO completion interrupts
are delayed. At the end of initiating IOs, the driver schedules for
cmd completion if there are pending cmds. A timer-based interrupt has
also been added to prevent IO completion from being delayed
indefinitely in the case that no new IOs are initiated. Some
formatting issues in resume, suspend comment block also corrected
Signed-off-by: Bo Yang <bo.yang@lsi.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
bo yang [Fri, 9 Nov 2007 09:14:00 +0000 (04:14 -0500)]
[SCSI] megaraid_sas: check max_sgl reported by FW for setting max_sectors_per_req
1. Setting the max_sectors_per_req based on max SGL supported by the
FW. Prior versions calculated this value from controller info's
max_sectors_1, max_sectors_2. For certain controllers/FW, this was
resulting in a value greater than max SGL supported by the FW. Now
we take the min of max sgl from FW and max_sectors calculation.
2. Increased MFI_POLL_TIMEOUT_SECS to 60 seconds from 10. FW may take
a max of 60 seconds to respond to the INIT cmd.
Signed-off-by: Bo Yang <bo.yang@lsi.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tony Battersby [Fri, 9 Nov 2007 18:04:35 +0000 (13:04 -0500)]
[SCSI] 3w-9xxx: fix abysmal write performance on some motherboards
The 3ware 9500S-8 SATA RAID controller exhibits terrible write
performance when PCI memory-write-and-invalidate is disabled. This is
easy to demonstrate by replacing pci_try_set_mwi() in the patch below
with pci_clear_mwi(). My benchmarks show the following:
Most motherboards will enable MWI without the driver having to set it
explicitly, so most people probably wouldn't encounter this problem.
For the few motherboards that don't enable it, this patch could give a
16x performance improvement for writing.
This issue does not seem to affect the 9550SX controller, but the patch
doesn't hurt it either. I haven't tested any of the other 3ware
controllers.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com> Acked-by: adam radford <aradford@gmail.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
projects / linux-2.6 / log