Fabio Checconi [Thu, 20 Mar 2008 22:54:58 +0000 (15:54 -0700)]
bridge: use time_before() in br_fdb_cleanup()
In br_fdb_cleanup() next_timer and this_timer are in jiffies, so they
should be compared using the time_after() macro.
Signed-off-by: Fabio Checconi <fabio@gandalf.sssup.it> Signed-off-by: Stephen Hemminger <stephen.hemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Emelyanov [Thu, 20 Mar 2008 22:39:41 +0000 (15:39 -0700)]
audit: netlink socket can be auto-bound to pid other than current->pid (v2)
From: Pavel Emelyanov <xemul@openvz.org>
This patch is based on the one from Thomas.
The kauditd_thread() calls the netlink_unicast() and passes
the audit_pid to it. The audit_pid, in turn, is received from
the user space and the tool (I've checked the audit v1.6.9)
uses getpid() to pass one in the kernel. Besides, this tool
doesn't bind the netlink socket to this id, but simply creates
it allowing the kernel to auto-bind one.
That's the preamble.
The problem is that netlink_autobind() _does_not_ guarantees
that the socket will be auto-bound to the current pid. Instead
it uses the current pid as a hint to start looking for a free
id. So, in case of conflict, the audit messages can be sent
to a wrong socket. This can happen (it's unlikely, but can be)
in case some task opens more than one netlink sockets and then
the audit one starts - in this case the audit's pid can be busy
and its socket will be bound to another id.
The proposal is to introduce an audit_nlk_pid in audit subsys,
that will point to the netlink socket to send packets to. It
will most often be equal to audit_pid. The socket id can be
got from the skb's netlink CB right in the audit_receive_msg.
The audit_nlk_pid reset to 0 is not required, since all the
decisions are taken based on audit_pid value only.
Later, if the audit tools will bind the socket themselves, the
kernel will have to provide a way to setup the audit_nlk_pid
as well.
A good side effect of this patch is that audit_pid can later
be converted to struct pid, as it is not longer safe to use
pid_t-s in the presence of pid namespaces. But audit code still
uses the tgid from task_struct in the audit_signal_info and in
the audit_filter_syscall.
Signed-off-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: Pavel Emelyanov <xemul@openvz.org> Acked-by: Eric Paris <eparis@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Yasevich [Thu, 20 Mar 2008 22:17:14 +0000 (15:17 -0700)]
[SCTP]: Fix a race between module load and protosw access
There is a race is SCTP between the loading of the module
and the access by the socket layer to the protocol functions.
In particular, a list of addresss that SCTP maintains is
not initialized prior to the registration with the protosw.
Thus it is possible for a user application to gain access
to SCTP functions before everything has been initialized.
The problem shows up as odd crashes during connection
initializtion when we try to access the SCTP address list.
The solution is to refactor how we do registration and
initialize the lists prior to registering with the protosw.
Care must be taken since the address list initialization
depends on some other pieces of SCTP initialization. Also
the clean-up in case of failure now also needs to be refactored.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Acked-by: Sridhar Samudrala <sri@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
If a rule using ipt_recent is created with a hit count greater than
ip_pkt_list_tot, the rule will never match as it cannot keep track
of enough timestamps. This patch makes ipt_recent refuse to create such
rules.
With ip_pkt_list_tot's default value of 20, the following can be used
to reproduce the problem.
nc -u -l 0.0.0.0 1234 &
for i in `seq 1 100`; do echo $i | nc -w 1 -u 127.0.0.1 1234; done
This limits it to 20 packets:
iptables -A OUTPUT -p udp --dport 1234 -m recent --set --name test \
--rsource
iptables -A OUTPUT -p udp --dport 1234 -m recent --update --seconds \
60 --hitcount 20 --name test --rsource -j DROP
While this is unlimited:
iptables -A OUTPUT -p udp --dport 1234 -m recent --set --name test \
--rsource
iptables -A OUTPUT -p udp --dport 1234 -m recent --update --seconds \
60 --hitcount 21 --name test --rsource -j DROP
With the patch the second rule-set will throw an EINVAL.
Reported-by: Sean Kennedy <skennedy@vcn.com> Signed-off-by: Daniel Hokka Zakrisson <daniel@hozac.com> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 17 Mar 2008 16:52:24 +0000 (09:52 -0700)]
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
ahci: Add Marvell 6121 SATA support
pata_ali: use atapi_cmd_type() to determine cmd type instead of transfer size
ahci: implement skip_host_reset parameter
ahci: request all PCI BARs
devres: implement pcim_iomap_regions_request_all()
libata-acpi: improve dock event handling
Tejun Heo [Tue, 11 Mar 2008 02:35:00 +0000 (11:35 +0900)]
pata_ali: use atapi_cmd_type() to determine cmd type instead of transfer size
pata_ali was using qc->nbytes to determine whether a command is
data transfer type or not. As now qc->nbytes can be extended by
padding and draining buffers, these tests are not useful anymore.
Use atapi_cmd_type() instead.
Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Mon, 10 Mar 2008 01:25:25 +0000 (10:25 +0900)]
ahci: implement skip_host_reset parameter
Under certain circumstances (SSP turned off by the BIOS) and for
debugging purposes, skipping global controller reset is helpful. Add
a kernel parameter for it.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Tue, 11 Mar 2008 10:52:31 +0000 (19:52 +0900)]
ahci: request all PCI BARs
ahci is often implemented with accompanying SFF compatible interface
and legacy IDE driver may attach to the legacy IO ports when the
controller is already claimed by ahci and vice-versa. This patch
makes ahci use pcim_iomap_regions_request_all() so that all IO regions
are claimed on attach.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some drivers need to reserve all PCI BARs to prevent other drivers
misusing unoccupied BARs. pcim_iomap_regions_request_all() requests
all BARs and iomap specified BARs.
Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Greg Kroah-Hartman <gregkh@suse.de> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
ucc_geth: use correct thread number for 10/100Mbps link
Use thread number of 1 for 10/100Mbps link instead of 4.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se> Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Ralf Baechle [Sat, 8 Mar 2008 16:58:33 +0000 (16:58 +0000)]
[IOC3] Fix section missmatch
LD drivers/net/built-in.o
WARNING: drivers/net/built-in.o(.text+0x3468): Section mismatch in reference fro
m the function ioc3_probe() to the function .devinit.text:ioc3_serial_probe()
The function ioc3_probe() references
the function __devinit ioc3_serial_probe().
This is often because ioc3_probe lacks a __devinit
annotation or the annotation of ioc3_serial_probe is wrong.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Ayaz Abdulla [Mon, 10 Mar 2008 19:58:21 +0000 (14:58 -0500)]
forcedeth: limit tx to 16
This is a critical patch which adds a workaround for a HW bug. The patch
will limit the number of outstanding tx packets to 16. Otherwise, the HW
could send out packets with bad checksums.
The driver will still setup the tx packets into the ring, however, will
only set the Valid bit on 16 packets at a time.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Divy Le Ray [Thu, 13 Mar 2008 07:13:30 +0000 (00:13 -0700)]
cxgb3: Fix transmit queue stop mechanism
The last change in the Tx queue stop mechanism opens a window
where the Tx queue might be stopped after pending credits
returned.
Tx credits are returned via a control message generated by the HW.
It returns tx credits on demand, triggered by a completion bit
set in selective transmit packet headers.
The current code can lead to the Tx queue stopped
with all pending credits returned, and the current frame
not triggering a credit return. The Tx queue will then never be
awaken.
The driver could alternatively request a completion for packets
that stop the queue. It's however safer at this point to go back
to the pre-existing behaviour.
Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Stefan Roese [Thu, 13 Mar 2008 15:59:43 +0000 (16:59 +0100)]
NEWEMAC: Add compatible "ibm,tah" to tah matching table
Add "ibm,tah" to the compatible matching table of the ibm_newemac
tah driver. The type "tah" is still preserved for compatibility reasons.
New dts files should use the compatible property though.
Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch should resolve a problem that's troubled support for
some RNDIS peripherals. It seems to have boiled down to using a
variable to establish transfer size limits before it was assigned,
which caused those devices to fallback to a default "jumbogram"
mode we don't support. Fix by assigning it earlier for RNDIS.
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
[ cleanups ] Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Problem Description and Fix
---------------------------
When a pause packet(with destination as reserved Multicast address) is
received by the EMAC hardware to control the flow of frames being
transmitted by it, it is dropped by the hardware unless the reserved
Multicast address is hashed in to the GAHT[1-4] registers. This code fix
adds the default reserved multicast address to the GAHT[1-4] registers
in the EMAC(s) present on the chip. The flow control with Pause packets
will only work if the following register bits are programmed in EMAC:
EMACx_MR1[APP] = 1
EMACx_RMR[BAE] = 1
EMACx_RMR[MAE] = 1
Behavior that may be observed in a running system
-------------------------------------------------
A host transferring data from a PPC based system may send a Pause packet
to the PPC EMAC requesting it to slow down the flow of packets. If the
default reserved multicast MAC address is not programmed into the
GAHT[1-4] registers this Pause packet will be dropped by PPC EMAC and no
Flow Control will be done.
Signed-off-by: Pravin M. Bathija <pbathija@amcc.com> Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Jeff Garzik <jeff@garzik.org>
The problem can be triggered with a high amount of host->guest traffic.
I think its the following race:
poll says netif_rx_complete
poll calls enable_cb
enable_cb opens the interrupt mask
a new packet comes, an interrupt is triggered----\
enable_cb sees that there is more work |
enable_cb disables the interrupt |
. V
. interrupt is delivered
. skb_recv_done does atomic napi test, ok
some waiting disable_cb is called->check fails->bang!
.
poll would do napi check
poll would do disable_cb
The fix is to let enable_cb not disable the interrupt again, but expect the
caller to do the cleanup if it returns false. In that case, the interrupt is
only disabled, if the napi test_set_bit was successful.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (cleaned up doco)
Rusty Russell [Tue, 18 Mar 2008 03:58:15 +0000 (22:58 -0500)]
virtio: handle > 2 billion page balloon targets
If the host asks for a huge target towards_target() can overflow, and
we up oops as we try to release more pages than we have. The simple
fix is to use a 64-bit value.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Anthony Liguori [Sun, 2 Mar 2008 22:37:48 +0000 (16:37 -0600)]
virtio: Use spin_lock_irqsave/restore for virtio-pci
virtio-pci acquires its spin lock in an interrupt context so it's necessary
to use spin_lock_irqsave/restore variants. This patch fixes guest SMP when
using virtio devices in KVM.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Al Viro [Sun, 16 Mar 2008 22:22:04 +0000 (22:22 +0000)]
epic100 endianness annotations and fixes
* "powerpc or sparc" is not the same as "big-endian", fix the ifdef
* since we tell the card to byteswap the descriptors on big-endian,
we ought to leave them host-endian...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Helge Deller [Wed, 26 Dec 2007 17:07:01 +0000 (18:07 +0100)]
[PARISC] head.S: section mismatch fixes
- move boot_args[] into the init section
- move $global$ into the read_mostly section
- fix the following two section mismatches:
WARNING: vmlinux.o(.text+0x9c): Section mismatch: reference to .init.text:start_kernel (between '$pgt_fill_loop' and '$is_pa20')
WARNING: vmlinux.o(.text+0xa0): Section mismatch: reference to .init.text:start_kernel (between '$pgt_fill_loop' and '$is_pa20')
This is bogus on parisc, since page zero in kernel virtual space is the
gateway page for syscall entry, and should not be read from the kernel.
(That, and we really don't like the kernel faulting on its own address
space...)
Kyle McMartin [Sat, 1 Mar 2008 18:30:19 +0000 (10:30 -0800)]
[PARISC] clean up show_stack
When we show_regs, we obviously have a struct pt_regs of the calling
frame. Use these in show_stack so we don't have the entire bogus call trace
up to the show_stack call.
Adrian Bunk [Tue, 26 Feb 2008 19:55:17 +0000 (21:55 +0200)]
[PARISC] move defconfig to arch/parisc/configs/
This patch moves the default parisc defconfig to
arch/parisc/configs/generic_defconfig where it belongs and selects it as
the default defconfig through KBUILD_DEFCONFIG.
Signed-off-by: Adrian Bunk <adrian.bunk@movial.fi> Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Kyle McMartin [Tue, 19 Feb 2008 07:34:34 +0000 (23:34 -0800)]
[PARISC] pdc_console: fix bizarre panic on boot
Commit 721fdf34167580ff98263c74cead8871d76936e6 introduced a subtle bug
by accidently removing the "static" from iodc_dbuf. This resulted in, what
appeared to be, a trap without *current set to a task. Probably the result of
a trap in real mode while calling firmware.
Also do other misc clean ups. Since the only input from firmware is non
blocking, share iodc_dbuf between input and output, and spinlock the
only callers.
Kyle McMartin [Tue, 19 Feb 2008 07:26:46 +0000 (23:26 -0800)]
[PARISC] dump_stack in show_regs
Originally, show_stack was used in BUG() output. However, a recent commit
changed it to print register state (no idea what that's supposed to help,
really...) and parisc was missing a backtrace because of it.
It did ugly things to the init sequence to populate the rootfs image
early, but that just ended up showing other problems with the whole
approach. The fact is, the VFS layer simply isn't initialized this
early, and the relevant ACPI code should either run much later, or this
shouldn't be done at all.
For 2.6.25, we'll just pick the latter option. We can revisit this
concept later if necessary.
Cc: Dave Hansen <haveblue@us.ibm.com> Cc: Tilman Schmidt <tilman@imap.cc> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Thomas Renninger <trenn@suse.de> Cc: Eric Piel <eric.piel@tremplin-utc.net> Cc: Len Brown <len.brown@intel.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Markus Gaugusch <dsdt@gaugusch.at> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ingo Molnar [Fri, 14 Mar 2008 21:17:08 +0000 (22:17 +0100)]
sched: simplify sched_slice()
Use the existing calc_delta_mine() calculation for sched_slice(). This
saves a divide and simplifies the code because we share it with the
other /cfs_rq->load users.
It also improves code size:
text data bss dec hex filename
42659 2740 144 45543 b1e7 sched.o.before
42093 2740 144 44977 afb1 sched.o.after
Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Peter Zijlstra [Fri, 14 Mar 2008 20:12:12 +0000 (21:12 +0100)]
sched: fix overload performance: buddy wakeups
Currently we schedule to the leftmost task in the runqueue. When the
runtimes are very short because of some server/client ping-pong,
especially in over-saturated workloads, this will cycle through all
tasks trashing the cache.
Reduce cache trashing by keeping dependent tasks together by running
newly woken tasks first. However, by not running the leftmost task first
we could starve tasks because the wakee can gain unlimited runtime.
Therefore we only run the wakee if its within a small
(wakeup_granularity) window of the leftmost task. This preserves
fairness, but does alternate server/client task groups.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Peter Zijlstra [Fri, 14 Mar 2008 19:55:51 +0000 (20:55 +0100)]
sched: min_vruntime fix
Current min_vruntime tracking is incorrect and will cause serious
problems when we don't run the leftmost task for some reason.
min_vruntime does two things; 1) it's used to determine a forward
direction when the u64 vruntime wraps, 2) it's used to track the
leftmost vruntime to position newly enqueued tasks from.
The current logic advances min_vruntime whenever the current task's
vruntime advance. Because the current task may pass the leftmost task
still waiting we're failing the second goal. This causes new tasks to be
placed too far ahead and thus penalizes their runtime.
Fix this by making min_vruntime the min_vruntime of the waiting tasks by
tracking it in enqueue/dequeue, and compare against current's vruntime
to obtain the absolute minimum when placing new tasks.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix a hard to trigger crash seen in the -rt kernel that also affects
the vanilla scheduler.
There is a race condition between schedule() and some dequeue/enqueue
functions; rt_mutex_setprio(), __setscheduler() and sched_move_task().
When scheduling to idle, idle_balance() is called to pull tasks from
other busy processor. It might drop the rq lock. It means that those 3
functions encounter on_rq=0 and running=1. The current task should be
put when running.
The current process of CPU1(P1) is scheduling. Deactivated P1, and the
scheduler looks for another process on other CPU's runqueue because CPU1
will be idle. idle_balance(), load_balance_newidle() and
double_lock_balance() are called and double_lock_balance() could drop
the rq lock. On the other hand, CPU0 is trying to boost the priority of
P1. The result of boosting only P1's prio and sched_class are changed to
RT. The sched entities of P1 and P1's group are never put. It makes
cfs_rq invalid, because the cfs_rq has curr and no leaf, but
pick_next_task_fair() is called, then the kernel panics.
J. Bruce Fields [Fri, 14 Mar 2008 23:37:11 +0000 (19:37 -0400)]
nfsd: fix oops on access from high-numbered ports
This bug was always here, but before my commit 6fa02839bf9412e18e77
("recheck for secure ports in fh_verify"), it could only be triggered by
failure of a kmalloc(). After that commit it could be triggered by a
client making a request from a non-reserved port for access to an export
marked "secure". (Exports are "secure" by default.)
The result is a struct svc_export with a reference count one too low,
resulting in likely oopses next time the export is accessed.
The reference counting here is not straightforward; a later patch will
clean up fh_verify().
Thanks to Lukas Hejtmanek for the bug report and followup.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu> Cc: Lukas Hejtmanek <xhejtman@ics.muni.cz> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jarod Wilson [Wed, 12 Mar 2008 21:43:26 +0000 (17:43 -0400)]
firewire: fw-ohci: use dma_alloc_coherent for ar_buffer
Currently, we do nothing to guarantee we have a consistent DMA buffer for
asynchronous receive packets. Rather than doing several sync's following a
dma_map_single() to get consistent buffers, just switch to using
dma_alloc_coherent().
Resolves constant buffer failures on my own x86_64 laptop w/4GB of RAM and
likely to fix a number of other failures witnessed on x86_64 systems with
4GB of RAM or more.
Signed-off-by: Jarod Wilson <jwilson@redhat.com> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Tue, 11 Mar 2008 21:32:52 +0000 (22:32 +0100)]
ieee1394: sbp2: fix for SYM13FW500 bridge (Datafab disk)
Fix I/O errors due to SYM13FW500's inability to handle larger request
sizes. Reported by Piergiorgio Sartor <piergiorgio.sartor@nexgo.de> for
firewire-sbp2 in https://bugzilla.redhat.com/show_bug.cgi?id=436879
This fix is necessary because sbp2's default request size limit has been
lifted since 2.6.25-rc1.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Jarod Wilson <jwilson@redhat.com>
Stefan Richter [Tue, 11 Mar 2008 21:32:03 +0000 (22:32 +0100)]
firewire: fw-sbp2: fix for SYM13FW500 bridge (Datafab disk)
Fix I/O errors due to SYM13FW500's inability to handle larger request
sizes. Reported by Piergiorgio Sartor <piergiorgio.sartor@nexgo.de> in
https://bugzilla.redhat.com/show_bug.cgi?id=436879
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Jarod Wilson <jwilson@redhat.com>
Jarod Wilson [Fri, 7 Mar 2008 06:43:01 +0000 (01:43 -0500)]
firewire: fw-sbp2: set single-phase retry_limit
Per the SBP-2 specification, all SBP-2 target devices must have a BUSY_TIMEOUT
register. Per the 1394-1995 specification, the retry_limt portion of the
register should be set to 0x0 initially, and set on the target by a logged in
initiator (i.e., a Linux host w/firewire controller(s)).
Well, as it turns out, lots of devices these days have actually moved on to
starting to implement SBP-3 compliance, which says that retry_limit should
default to 0xf instead (yes, SBP-3 stomps directly on 1394-1995, oops).
Prior to this change, the firewire driver stack didn't touch retry_limit, and
any SBP-3 compliant device worked fine, while SBP-2 compliant ones were unable
to retransmit when the host returned an ack_busy_X, which resulted in stalled
out I/O, eventually causing the SCSI layer to give up and offline the device.
The simple fix is for us to set retry_limit to 0xf in the register for all
devices (which actually matches what the old ieee1394 stack did).
Prior to this change, a hard disk behind an SBP-2 Prolific PL-3507 bridge chip
would routinely encounter buffer I/O errors and wind up offlined by the SCSI
layer. With this change, I've encountered zero I/O failures moving tens of GB
of data around.
Signed-off-by: Jarod Wilson <jwilson@redhat.com> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Sat, 1 Mar 2008 01:42:56 +0000 (02:42 +0100)]
firewire: fw-ohci: PPC PMac platform code
Copied from ohci1394.c. This code is necessary to prevent machine check
exceptions when reloading or resuming the driver.
Tested on a 1st generation PowerBook G4 Titanium, which also needs the
pci_probe() hunk.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
I was able to reproduce the system exception on resume with a 3rd-gen
Titanium PowerBook G4 667, and this patch does let the system resume
successfully now.
Not quite clear if there was possibly an updated version coming using
pci_enable_device() instead of the pair of pmac_call_feature() calls,
but either way, this is a definite must-have, at least for older ppc
macs -- my Aluminum PowerBook G4/1.67 suspends and resumes without this
patch just fine.
Signed-off-by: Jarod Wilson <jwilson@redhat.com> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Stefan Richter [Sat, 23 Feb 2008 11:24:57 +0000 (12:24 +0100)]
firewire: endianess annotations
Kills warnings from 'make C=1 CHECKFLAGS="-D__CHECK_ENDIAN__" modules':
drivers/firewire/fw-transaction.c:771:10: warning: incorrect type in assignment (different base types)
drivers/firewire/fw-transaction.c:771:10: expected unsigned int [unsigned] [usertype] <noident>
drivers/firewire/fw-transaction.c:771:10: got restricted unsigned int [usertype] <noident>
drivers/firewire/fw-transaction.h:93:10: warning: incorrect type in assignment (different base types)
drivers/firewire/fw-transaction.h:93:10: expected unsigned int [unsigned] [usertype] <noident>
drivers/firewire/fw-transaction.h:93:10: got restricted unsigned int [usertype] <noident>
drivers/firewire/fw-ohci.c:1490:8: warning: restricted degrades to integer
drivers/firewire/fw-ohci.c:1490:35: warning: restricted degrades to integer
drivers/firewire/fw-ohci.c:1516:5: warning: cast to restricted type
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Jarod Wilson <jwilson@redhat.com>
Linus Torvalds [Thu, 13 Mar 2008 20:25:32 +0000 (13:25 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IPoIB: Allocate priv->tx_ring with vmalloc()
IPoIB/cm: Set tx_wr.num_sge in connected mode post_send()
IPoIB: Don't drop multicast sends when they can be queued
IB/ipath: Reset the retry counter for RDMA_READ_RESPONSE_MIDDLE packets
IB/ipath: Fix error completion put on send CQ instead of recv CQ
IB/ipath: Fix RC QP initialization
IB/ipath: Fix potentially wrong RNR retry counter returned in ipath_query_qp()
IB/ipath: Fix IB compliance problems with link state vs physical state
Jan Beulich [Thu, 13 Mar 2008 09:13:30 +0000 (09:13 +0000)]
avoid endless loops in lib/swiotlb.c
Commit 681cc5cd3efbeafca6386114070e0bfb5012e249 ("iommu sg merging:
swiotlb: respect the segment boundary limits") introduced two
possibilities for entering an endless loop in lib/swiotlb.c:
- if max_slots is zero (possible if mask is ~0UL)
- if the number of slots requested fits into a swiotlb segment, but is
too large for the part of a segment which remains after considering
offset_slots
This fixes them
Signed-off-by: Jan Beulich <jbeulich@novell.com> Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / linux-2.6 / log