Mattias Nissler [Sun, 9 Mar 2008 21:41:22 +0000 (22:41 +0100)]
rt2x00: Don't use unitialized rxdesc->size
rxdesc->size is unitialized before the desriptor has been read.
Move the truncation of the sk buffer to the moment all variables
have been initialized.
Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mattias Nissler [Sun, 9 Mar 2008 21:39:32 +0000 (22:39 +0100)]
rt2x00: Use the correct size when copying the control info in txdone
The sizeof() operator was incorrectly applied to the pointer, not the struct.
Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mattias Nissler [Sun, 9 Mar 2008 21:38:54 +0000 (22:38 +0100)]
rt2x00: Initialize TX control field in data entries
In the TX path, the driver didn't copy the TX control data structure. Thus, it
was invalid in the TX done handler, causing serious trouble and misbehaviour.
Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Sun, 9 Mar 2008 21:38:18 +0000 (22:38 +0100)]
rt2x00: Align RX descriptor to 4 bytes
Some architectures give problems when reading
RX frame descriptor words when the descriptor
is not aligned on a 4 byte boundrary.
Due to optimalizations for the ieee80211 payload
4 byte alignment, it is no longer guarenteed
that the descriptor is placed on the 4 byte
boundrary (In fact, for rt73usb it is absolutely
never aligned to 4 bytes, for rt2500usb it depends
on the length of the payload).
This will copy the descriptor to a 4 byte aligned
location before it is read for the first time.
This will also move the payload data alignment
in rt2x00usb (instead of inside the driver) where
it has always belonged.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Holger Schurig [Wed, 5 Mar 2008 06:05:32 +0000 (07:05 +0100)]
libertas: implement SSID scanning for SIOCSIWSCAN
After my bit scan re-writing the SIOCSIWSCAN wext ioctl no longer supported
scanning for a specific SSID. However, wpa_supplicant is a possible user of
this ioctl, so here is code that add's this.
While passing, removed even more of the debugfs-based scanning. You can (and
should) the SIOCSIWSCAN to ask for scans, so there is no need for
proprietary interfaces for scanning. And, besides, the scan result couldn't
be used further, e.g. not for associating.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adrian Bunk [Tue, 4 Mar 2008 23:26:15 +0000 (15:26 -0800)]
the scheduled rc80211-simple.c removal
Signed-off-by: Adrian Bunk <bunk@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adrian Bunk [Tue, 4 Mar 2008 23:26:14 +0000 (15:26 -0800)]
the scheduled ieee80211 softmac removal
Signed-off-by: Adrian Bunk <bunk@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adrian Bunk [Tue, 4 Mar 2008 23:26:12 +0000 (15:26 -0800)]
the scheduled bcm43xx removal
Signed-off-by: Adrian Bunk <bunk@kernel.org> Cc: <Larry.Finger@lwfinger.net> Cc: <stefano.brivio@polimi.it> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adrian Bunk [Tue, 4 Mar 2008 23:26:06 +0000 (15:26 -0800)]
make b43_mac_{enable,suspend}() static
b43_mac_{enable,suspend}() can now become static.
Signed-off-by: Adrian Bunk <bunk@kernel.org> Acked-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reinette Chatre [Fri, 7 Mar 2008 21:47:20 +0000 (13:47 -0800)]
iwlwifi: fix potential lock inversion deadlock
This is a change to a previous patch ("iwlwifi: 3945 split tx_complete
to command and packet function") to ensure we do not have hardirq safe
locks (priv->lock in this case) depend on hardirq unsafe locks.
We only call iwl3945_tx_queue_reclaim while in a tasklet so we have to use
the irqsafe version of the function.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
wireless: correct warnings from using '%llx' for type 'u64'
drivers/net/wireless/ath5k/debug.c: In function 'read_file_tsf': drivers/net/wireless/ath5k/debug.c:203: warning: format '%016llx'
expects type 'long long unsigned int', but argument 4 has type 'u64' drivers/net/wireless/ath5k/debug.c:203: warning: format '%016llx'
expects type 'long long unsigned int', but argument 4 has type 'u64' drivers/net/wireless/ath5k/debug.c: In function 'read_file_beacon':
drivers/net/wireless/ath5k/debug.c:274: warning: format '%016llx' expects type 'long long unsigned int', but argument 4 has type 'u64'
drivers/net/wireless/ath5k/debug.c:274: warning: format '%016llx' expects type 'long long unsigned int', but argument 4 has type 'u64'
drivers/net/wireless/iwlwifi/iwl-4965.c: In function 'iwl4965_tx_status_reply_compressed_ba':
drivers/net/wireless/iwlwifi/iwl-4965.c:3907: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'u64'
drivers/net/wireless/iwlwifi/iwl-4965.c: In function 'iwl4965_rx_reply_compressed_ba':
drivers/net/wireless/iwlwifi/iwl-4965.c:4039: warning: format '%llx' expects type 'long long unsigned int', but argument 6 has type '__le64'
drivers/net/wireless/iwlwifi/iwl-4965.c:4046: warning: format '%llx' expects type 'long long unsigned int', but argument 5 has type 'u64'
drivers/net/wireless/iwlwifi/iwl4965-base.c: In function 'iwl4965_tx_status_reply_tx':
drivers/net/wireless/iwlwifi/iwl4965-base.c:3661: warning: format '%llx' expects type 'long long unsigned int', but argument 6 has type 'u64'
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bruno Randolf [Wed, 5 Mar 2008 09:36:26 +0000 (18:36 +0900)]
ath5k: work around wrong beacon rx timestamp in IBSS mode
atheros hardware has a problem with the rx timestamp of some IBSS beacons when
they caused a TSF update (they have the same BSSID).
the rx timestamp is wrong especially if the beacon frames get bigger than 78
byte (at least on AR5213 and AR5414 hardware). in that case ath5k_extend_tsf()
will assume a rs_tstamp overflow and give us a timestamp too far in the past
which will cause mac80211 to merge IBSS on every beacon (which is not necessary
since the BSSID already matches). but in this case we know that the HW must
have synced to the beacons TSF and the rx timestamp must be later than that so
we can adjust mactime accordingly.
also rename the function to ath5k_check_ibss_tsf() and change comments, since
"hw merge" is better described as a TSF update.
Bruno Randolf [Wed, 5 Mar 2008 09:35:45 +0000 (18:35 +0900)]
ath5k: move rx and tx status structures out of hardware descriptor
move ath5k_tx_status and ath5k_rx_status structures out of the hardware
descriptor since they are not accessed by the hardware at all. they just
contain converted information from the hardware descriptor. since they are only
used in the rx and tx tasklets there is also no use to keep them for each
descriptor.
Bruno Randolf [Wed, 5 Mar 2008 09:35:23 +0000 (18:35 +0900)]
ath5k: struct ath5k_desc cleanups
* make struct ath5k_desc clearer by directly including unions of structures,
which correspond to the hardware descriptors of different HW versions (5210
and 5212). before they were casted at onto ath5k_desc at different points
(e.g. ds_hw[2]).
* rename some structures and variable names to make their use clearer, e.g.
struct ath5k_hw_4w_tx_desc to ath5k_hw_4w_tx_ctl.
* substitute "old" with "5210" and "new" with "5212" (eg. rename
ath5k_hw_proc_new_rx_status() to ath5k_hw_proc_5212_rx_status()) because old
and new are relative and we might have a newer structure at some point.
* unify structs ath5k_hw_old_rx_status and ath5k_hw_new_rx_status into one
ath5k_hw_rx_status, because they only differ in the flags and masks.
Ron Rindjunsky [Fri, 7 Mar 2008 01:36:56 +0000 (17:36 -0800)]
iwlwifi: grab NIC access when disabling aggregations
This patch grabs NIC access inside iwl4965_tx_queue_agg_disable, instead of the
caller doing it.
The caller must still hold priv->lock when calling the function.
Signed-off-by: Max Stepanov <max.stepanov@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Fri, 7 Mar 2008 01:36:55 +0000 (17:36 -0800)]
iwlwifi: 3945 split tx_complete to command and packet function
This patch
1. removes cmd completion from iwl3945_tx_queue_reclaim
and creates iwl3945_cmd_queue_reclaim.
1. removes 11n relevant elements from this function
2. removes call to ieee80211_tx_status_irqsafe
and uses ieee80211_tx_status only
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Fri, 7 Mar 2008 01:36:54 +0000 (17:36 -0800)]
iwlwifi: Fix 3945 rate scaling
This patch fix 3945 rate scaling after cfg80211 rate/band changes
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Fri, 7 Mar 2008 01:36:53 +0000 (17:36 -0800)]
iwlwifi: queue functions cleanup
This patch moves
1. iwl_queue_inc_wrap and int iwl_queue_dec_wrap
into iwl-helpers.h these two functions are identical to common
for both iwl3956 and iwl4965
2. renames x2_queue_used to iwl3945_x2_queue_used
3. exports iwl3945_queue_space out of iwl3964-base.c
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Assaf Krauss [Thu, 6 Mar 2008 18:40:20 +0000 (10:40 -0800)]
iwlwifi: Moving EEPROM handling in iwlcore module
This patch move EEPROM code into iwl core module
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Thu, 6 Mar 2008 18:40:19 +0000 (10:40 -0800)]
iwlwifi: add iwl-core module
This patch adds iwl-core module to iwlwifi driver.
This module will contain common code and infrastracture for iwlwifi
driver
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Wed, 5 Mar 2008 19:31:00 +0000 (11:31 -0800)]
iwlwifi: fix locking unbalance in 4965 rate scale
This patch fixes locking unbalance after adding rcu locking
for sta
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cancels an ongoing HW scan upon association. Not doing this
resulted in instability in association.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Wed, 5 Mar 2008 02:09:31 +0000 (18:09 -0800)]
iwlwifi: Take the fw file name from the iwl_cfg.
This patch adds fw_name to iwl_cfg. This allows run time selection
of needed fw/ucode file
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Wed, 5 Mar 2008 02:09:30 +0000 (18:09 -0800)]
iwlwifi: add struct iwl_cfg
This patch introduces struct iwl_cfg. struct iwl_cfg defines static
configuration for each device type and sku. It is passed as driver_data
to the bus probe function.
This patch also introduce new common header file iwl-core.h
which will represent core functionality of iwlwifi driver
3945ABG uses separate iwl-3945-dev.h header file for now
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Wed, 5 Mar 2008 02:09:29 +0000 (18:09 -0800)]
iwlwifi: Move HBUS address to iwl-csr.h
HBUS is accessed through CSR registers
moved to iwl-csr.h
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Wed, 5 Mar 2008 02:09:28 +0000 (18:09 -0800)]
iwlwifi: extract iwl-csr.h
This patch extract CSR Register definition into separate
header files as most of the definition are commons to both
3945 and 4965.
Definitions specific for 3945 and 4965 are properly prefixed
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ron Rindjunsky [Wed, 5 Mar 2008 02:09:27 +0000 (18:09 -0800)]
iwlwifi: use mac80211_tx_control_flags
This patch makes use of the new mac80211_tx_control_flags and tx_rate to
pass Tx data, regular and 11n, from the HW tx response into the rate scaling.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ron Rindjunsky [Wed, 5 Mar 2008 02:09:26 +0000 (18:09 -0800)]
mac80211: adding mac80211_tx_control_flags and HT flags
This patch makes enum from the defines previously dwelled inside
ieee80211_tx_control for better readability.
The patch also addes HT flags, for 802.11n drivers:
- IEEE80211_TXCTL_OFDM_HT: request low-level driver to use HT OFDM rates
- IEEE80211_TXCTL_GREEN_FIELD: use green field protection
- IEEE80211_TXCTL_DUP_DATA: duplicate data on both 20 Mhz channels
- IEEE80211_TXCTL_40_MHZ_WIDTH: send this frame in 40Mhz width
- IEEE80211_TXCTL_SHORT_GI: send this frame with short guard interval
Tx command can be a combination of any of these flags, along with
bitrate represented by ieee80211_rate. this will allow legacy drivers to
switch easily to any 11n rate representation.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> CC: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Guy Cohen [Wed, 5 Mar 2008 02:09:25 +0000 (18:09 -0800)]
iwlwifi: 802.11n spec removes AUTO offset for FAT channel
This patch adapts to 802.11 patch and remove AUTO offset for FAT
channel
Signed-off-by: Guy Cohen <guy.cohen@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michael Buesch [Fri, 7 Mar 2008 14:50:02 +0000 (15:50 +0100)]
b43: Add TX statistics debugging counters
This adds a few debugging counters, that are useful for debugging the
"card does not transmit" or "connection is unstable" kind of problems.
It's also useful for tuning an RC algorithm.
Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michael Buesch [Thu, 6 Mar 2008 15:32:46 +0000 (16:32 +0100)]
b43: Rename the DMA ring pointers
Rename the DMA ring pointers to have more descriptive and standard
names. Also remove the 6th unused TX ring. We can add it back later,
if we need it. The unused TX-status rx-ring is also removed, as that's
only used by legacy devices not supported by this driver anyway.
This is no functional change, except less memory allocation for
the removed rings.
Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 5 Mar 2008 19:39:31 +0000 (20:39 +0100)]
mac80211: don't call conf_tx under RCU lock
Reinette pointed out that with the sta_info RCU-ification
the behaviour here changed and the conf_tx callback is
now invoked under RCU read lock. That is not necessary so
this patch restores the original behaviour
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Tested-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nick Kossifidis [Fri, 7 Mar 2008 16:52:51 +0000 (11:52 -0500)]
ath5k: Add 2413 to srev_names so that it shows up during module load
Add 2413 to srev_names so that it shows up during module load.
This is based on the new patch 7 which did not introduce a helper
on ath5k_hw_reset().
Changes-licensed-under: 3-clause-BSD Signed-off-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: Luis R. Rodriguez <mcgrof@winlab.rutgers.edu> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nick Kossifidis [Fri, 7 Mar 2008 16:48:21 +0000 (11:48 -0500)]
ath5k: Make some changes to follow register dumps.
Make some changes which mimic what we see in register dumps.
This patch does not add a helper to ath5k_hw_reset(). It
does seem clear we need a re-shuffle around ath5k_hw_reset()
though as code in there is lengthy and already hitting 80-char
limit. This can be dealt with later though.
Changes-licensed-under: ISC Signed-off-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: Luis R. Rodriguez <mcgrof@winlab.rutgers.edu> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nick Kossifidis [Thu, 28 Feb 2008 21:20:52 +0000 (16:20 -0500)]
ath5k: Fixes for PCI-E cards
* Fix nic_wakeup for PCI-E chips (don't set AR5K_RESET_CTL_PCI bit)
* Fix dma size setting for PCI-E chips (thanx to Bob Copeland).
Changes-licensed-under: ISC Signed-off-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: Luis R. Rodriguez <mcgrof@winlab.rutgers.edu> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nick Kossifidis [Thu, 28 Feb 2008 19:51:40 +0000 (14:51 -0500)]
ath5k: Remove RF5413 from rf gain optimization functions
* Since RF2413 it seems that RF_BUFFER settings are different (notice
that the last part -"bank 7" or whatever- is smaller than in 5111/5112).
So until we know what's going on we assume there is no gain optimization
stuff in post-5112 chips.
Changes-licensed-under: ISC Signed-off-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: Luis R. Rodriguez <mcgrof@winlab.rutgers.edu> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nick Kossifidis [Thu, 28 Feb 2008 19:50:50 +0000 (14:50 -0500)]
ath5k: more RF2413 stuff
* Add AR5K_RF2413 to radio check during hw_reset so it doesn't complain
* Write ah_phy_spending value we set during attach instead of checking
each time for radio revision
* Skip txpower setup for RF2413 because it can't transmit with it
(weird thing is that RF5413 has no problem with it).
Changes-licensed-under: ISC Signed-off-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: Luis R. Rodriguez <mcgrof@winlab.rutgers.edu> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nick Kossifidis [Thu, 28 Feb 2008 19:49:05 +0000 (14:49 -0500)]
ath5k: Identify RF2413 and deal with PHY_SPENDING
* Attach RF2413.
* Propertly handle different AR5K_PHY_SPENDING settings for each RF
chip by adding a field in ath5k_hw. This way we won't have to check
inside hw_reset (see next patch).
Changes-licensed-under: ISC Signed-off-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: Luis R. Rodriguez <mcgrof@winlab.rutgers.edu> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nick Kossifidis [Thu, 28 Feb 2008 19:43:51 +0000 (14:43 -0500)]
ath5k: Add RF2413 initial settings
* Add initial settings for RF2413
Changes-licensed-under: ISC Signed-off-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: Luis R. Rodriguez <mcgrof@winlab.rutgers.edu> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nick Kossifidis [Thu, 28 Feb 2008 19:40:00 +0000 (14:40 -0500)]
ath5k: Add RF2413 srev values
* Add RF2413 srev values and a new entry on ath5k_radio enum for it
since it differs from RF5413 (it's not like 5112-2112).
Changes-licensed-under: ISC Signed-off-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: Luis R. Rodriguez <mcgrof@winlab.rutgers.edu> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Daniel Lezcano [Fri, 7 Mar 2008 19:16:55 +0000 (11:16 -0800)]
[NETNS][IPV6] mcast - handle several network namespace
This patch make use of the network namespace information at the right
places to handle the multicast for several network namespaces. It
makes the socket control to be per namespace too.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com> Signed-off-by: Benjamin Thery <benjamin.thery@bull.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Lezcano [Fri, 7 Mar 2008 19:16:26 +0000 (11:16 -0800)]
[NETNS][IPV6] tcp6 - handle several network namespace
We have the right network namespace at the right place now.
So make use of this information to make tcp6 per network namespace
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com> Signed-off-by: Benjamin Thery <benjamin.thery@bull.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Lezcano [Fri, 7 Mar 2008 19:16:02 +0000 (11:16 -0800)]
[NETNS][IPV6] tcp6 - make socket control per namespace
Instead of having a tcp6_socket global to all the namespace, there is
tcp6 socket control per namespace. That is consistent with which
namespace sent a RST and allows to pass the socket to the underlying
function to retrieve the network namespace.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com> Signed-off-by: Benjamin Thery <benjamin.thery@bull.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Lezcano [Fri, 7 Mar 2008 19:15:34 +0000 (11:15 -0800)]
[NETNS][IPV6] ndisc - make socket control per namespace
Make ndisc socket control per namespace.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com> Signed-off-by: Benjamin Thery <benjamin.thery@bull.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Lezcano [Fri, 7 Mar 2008 19:14:49 +0000 (11:14 -0800)]
[NETNS][IPV6] ndisc - make ndisc handle multiple network namespaces
Make ndisc handle multiple network namespaces:
Remove references to init_net, add network namespace parameters and add
pernet_operations for ndisc
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com> Signed-off-by: Benjamin Thery <benjamin.thery@bull.net> Signed-off-by: David S. Miller <davem@davemloft.net>
First, udplite is of such small cost, and it is a core protocol just
like TCP and normal UDP are.
We spent enormous amounts of effort to make udplite share as much code
with core UDP as possible. All of that work is less valuable if we're
just going to slap a config option on udplite support.
It is also causing build failures, as reported on linux-next, showing
that the changeset was not tested very well. In fact, this is the
second build failure resulting from the udplite change.
Finally, the config options provided was a bool, instead of a modular
option. Meaning the udplite code does not even get build tested
by allmodconfig builds, and furthermore the user is not presented
with a reasonable modular build option which is particularly needed
by distribution vendors.
Signed-off-by: David S. Miller <davem@davemloft.net>
Allan Stephens [Thu, 6 Mar 2008 23:08:10 +0000 (15:08 -0800)]
[TIPC]: Enhancements to message header writing
This patch makes two enhancements to the routine used to
set bit fields within a TIPC message header:
1) It now ignores any bits of the new field value that are not
covered by the mask being used. (Previously, if the new value
exceeded the size of the mask the extra bits could corrupt
other fields in the message header word being updated.)
2) The code has been optimized to minimize the number of run-time
endianness conversion operations by leveraging the fact that the
mask (and, in some cases, the value as well) is constant and the
necessary conversion can be performed by the compiler.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Allan Stephens [Thu, 6 Mar 2008 23:05:07 +0000 (15:05 -0800)]
[TIPC]: Removal of message header option code
This patch removes code associated with optional, user-specified
fields of the TIPC message header. Such fields were never
utilized by TIPC, and have now been removed from the protocol
specification.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
zd1211rw: support for mesh interface and beaconing
The previously unused CR_CAM_MODE register is set to MODE_AP_WDS. This makes the
driver ack mesh (WDS) frames. It does not affect Infra functionality of the
driver.
Previously missing beaconing support has been added. This might also help
implement a currently missing ah-hoc mode.
Support for interrupts from the device have been added, but we are not handling
most of them.
Mesh interfaces are considered associated as long as the interface is up.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Sat, 1 Mar 2008 23:52:00 +0000 (01:52 +0200)]
iwlwifi: Fix 52 rate report in rx status
This patch fixes reporting rate in RX packets in 52 band.
The rate was updated from CCK rate index instead of OFDM rate 6M
Most of the patch is collateral clean up
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Sat, 1 Mar 2008 23:36:04 +0000 (01:36 +0200)]
iwlwifi: refactor init geos function
This patch refactors init geos function. It also fixes few minor bugs.
IWL_MAX_RATE -> IWL_RATE_COUNT (IWL_MAX_RATE included also MCS setting)
There are 9 and 13 rates for 4965 in 2.4 and 5.2 respectively (rate 60)
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michael Buesch [Fri, 29 Feb 2008 10:36:12 +0000 (11:36 +0100)]
ssb: Add Gigabit Ethernet driver
This adds the Gigabit Ethernet driver for the SSB
Gigabit Ethernet core. This driver actually is a frontend to
the Tigon3 driver. So the real work is done by tg3.
This device is used in the Linksys WRT350N.
Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 5 Mar 2008 09:58:40 +0000 (10:58 +0100)]
mac80211: fix hardware scan completion
The mac80211 MLME requires restarting timers after a scan
completes but this wasn't done when hardware scan offload
was added, so add it now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Tested-by: Bill Moss <bmoss@clemson.edu> Cc: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211: fix mesh_path and sta_info get_by_idx functions
Skip properly entries whose dev does not match.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211: path IE fields macros, fix alignment problems and clean up
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis Carlos Cobo [Fri, 29 Feb 2008 23:46:08 +0000 (15:46 -0800)]
mac80211: add PLINK_ prefix and kernel doc to enum plink_state
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis Carlos Cobo [Fri, 29 Feb 2008 23:04:13 +0000 (15:04 -0800)]
mac80211: always force mesh_path deletions
Postponing the deletion is not really useful anymore.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis Carlos Cobo [Fri, 29 Feb 2008 22:49:37 +0000 (14:49 -0800)]
mac80211: delete mesh_path timer on mesh_path removal
This avoids dereferencing a no longer existing struct mesh_path.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis Carlos Cobo [Fri, 29 Feb 2008 22:30:32 +0000 (14:30 -0800)]
mac80211: clean up use of endianness conversion functions
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis Carlos Cobo [Fri, 29 Feb 2008 20:32:46 +0000 (12:32 -0800)]
mac80211: breakdown mesh network attributes in different extra fields for wext
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis Carlos Cobo [Fri, 29 Feb 2008 20:20:39 +0000 (12:20 -0800)]
mac80211: move comment to better location
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis Carlos Cobo [Fri, 29 Feb 2008 20:15:28 +0000 (12:15 -0800)]
mac80211: fix incorrect parenthesis
Pointed out by Johannes Berg.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis Carlos Cobo [Fri, 29 Feb 2008 20:13:38 +0000 (12:13 -0800)]
mac80211: fix mesh endianness sparse warnings and unmark it as broken
This patch fixes all the mesh related endianness warnings reported by sparse. As
they were the reason why Johannes marked mesh as BROKEN, that flag has been
removed.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Sat, 1 Mar 2008 18:32:18 +0000 (19:32 +0100)]
mac80211: always insert key into list
Today I hit one of my new WARN_ONs in the mac80211 code because
a key wasn't being freed correctly. After wondering for a while
I finally tracked it to the fact that STA keys aren't added to
the per-sdata key list correctly, they are supposed to always be
on that list, not just for default keys. This patch fixes that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Mon, 25 Feb 2008 15:27:50 +0000 (16:27 +0100)]
b43: verify sta_notify mac80211 callback
This helps verify that nothing bad is going on in mac80211,
it is unfortunately not possible to implement this generically
in mac80211 easily because there we can't assume that we only
have a single vif which b43 currently can assume.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 27 Feb 2008 08:56:40 +0000 (09:56 +0100)]
mac80211: fix sta_info mesh timer bug
I noticed a bug I introduced when mesh is enabled: sta_info_destroy()
will end up calling cancel_timer() on a timer that has never been
initialized because the timer is only initialized in mesh_plink_alloc(),
not in sta_info_alloc(). This patch moves the initialization of all mesh
related fields into sta_info_alloc(), adds a bit of sanity checking to
the cfg80211 handlers and sta_info_insert() and makes mesh_plink_alloc()
a static helper function that is only used from the mesh plink code.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Cc: Luis Carlos Cobo <luisca@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 26 Feb 2008 13:34:06 +0000 (14:34 +0100)]
mac80211: add documentation book
Quite a while ago I started this book. The required kernel-doc
patches have since gone into the tree so it is now possible to
build the book in mainline.
The actual documentation is still rather incomplete and not all
things are linked into the book, but this enables us to edit
the documentation collaboratively, hopefully driver authors can
add documentation based on their experience with mac80211.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 26 Feb 2008 09:53:57 +0000 (10:53 +0100)]
mac80211: don't clear next_hop in path reclaim
Luis pointed out that this path is going to be freed right
away anyway so there's no point in assigning next_hop.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Cc: Luis Carlos Cobo <luisca@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Mon, 25 Feb 2008 15:27:49 +0000 (16:27 +0100)]
mac80211: remove STA entries when taking down interface
When we take down an interface, we need to remove the STA info
items that belong to it because otherwise we might invoke a
sta_notify() callback in the driver when we later delete the
STA entries, but in that case the driver will already have
removed its knowledge of the interface they belonged to leading
to confusion. Also, we could invoke the set_tim() callback after
the driver removed its knowledge of the interface, which can
lead to a crash if it requests a beacon with a then-invalid vif
pointer!
A side effect of this patch is that, because it was easier, it
disallows changing the WDS peer while an interface is up. Should
that actually be necessary, it can be added back, but the WDS
peer STA entry may not be added while the interface is UP so for
now I've simplified the WDS peer's STA entry lifetime management.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Mon, 25 Feb 2008 15:27:48 +0000 (16:27 +0100)]
mac80211: clean up sta_info and document locking
This patch cleans up the sta_info struct and documents how
each set of variables is locked. Notably, flags locking is
completely missing. It also adds kernel-doc for some (but
not all yet) members of the struct.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Mon, 25 Feb 2008 15:27:47 +0000 (16:27 +0100)]
mac80211: split sta_info_add
sta_info_add() has two functions: allocating a station info
structure and inserting it into the hash table/list. Splitting
these two functions allows allocating with GFP_KERNEL in many
places instead of GFP_ATOMIC which is now required by the RCU
protection. Additionally, in many places RCU protection is now
no longer needed at all because between sta_info_alloc() and
sta_info_insert() the caller owns the structure.
This fixes a few race conditions with setting initial flags
and similar, but not all (see comments in ieee80211_sta.c and
cfg.c). More documentation on the existing races will be in
a follow-up patch.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Mon, 25 Feb 2008 15:27:46 +0000 (16:27 +0100)]
mac80211: RCU-ify STA info structure access
This makes access to the STA hash table/list use RCU to protect
against freeing of items. However, it's not a true RCU, the
copy step is missing: whenever somebody changes a STA item it
is simply updated. This is an existing race condition that is
now somewhat understandable.
This patch also fixes the race key freeing vs. STA destruction
by making sure that sta_info_destroy() is always called under
RTNL and frees the key.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Mon, 25 Feb 2008 15:24:38 +0000 (16:24 +0100)]
mac80211: clean up mesh RX path a bit more
Moves another ifdef into the sta_info header file in favour of
compiling more code even w/o CONFIG_MAC80211_MESH.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Cc: Luis Carlos Cobo <luisca@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Mon, 25 Feb 2008 09:11:50 +0000 (10:11 +0100)]
mac80211: add missing "break" statement in mesh code
This inserts a missing break statement which, if hit, would cause
the code to fall-through and unlock a spinlock twice. Noticed via
sparse's "lock count wrong in basic block" warning and careful
code inspection.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Cc: Luis Carlos Cobo <luisca@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
projects / linux-2.6 / log