Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Cc: "Antonino A. Daplas" <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jesper Juhl [Tue, 16 Oct 2007 08:29:26 +0000 (01:29 -0700)]
fbdev: Update Documentation/fb/00-INDEX
An update to Documentation/fb/00-INDEX is long overdue. This patch adds
entries for new files in the directory and removes entries for files that no
longer exist. The files are now also sorted alphabetically.
ps3fb: Add a `mode' parameter to ps3fb_get_res_table(), as in some cases it
should check the full-screen flag of the _new_ video mode instead of the
current video mode.
This bug caused spurious mode change failures when switching between
fullscreen and non-fullscreen modes using fbset, while ps3-video-mode worked
fine.
Masashi Kimoto [Tue, 16 Oct 2007 08:29:22 +0000 (01:29 -0700)]
ps3: Fix black and white stripes
Fix the black and white stripes issue with WUXGA monitor via HDMI.
It seems that when we use a VESA resolution from boot up, the AV settings
driver could not be initialized correctly. In that case we need a dummy
packet before VESA setting.
Pavel Pisa [Tue, 16 Oct 2007 08:29:21 +0000 (01:29 -0700)]
fbdev: Support for byte-reversed framebuffer formats
Allow generic frame-buffer code to correctly write texts and blit images for
1, 2 and 4 bit per pixel frame-buffer organizations when pixels in bytes are
organized to in opposite order than bytes in long type.
Overhead should be reasonable. If option is not selected, than compiler
should eliminate completely all overhead.
The feature is disabled at compile time if CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is
not set.
[adaplas]
Convert helper functions to macros if feature is not enabled.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz> Signed-off-by: Antonino Daplas <adaplas@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
nvidiafb: Add boot option to reverse i2c port assignment
There are a few nvidia hardware where the i2c port assignments are reversed,
i.e., the 1st i2c port is assigned to the secondary display and the 2nd i2c
port to the primary display. In most cases, if only 1 display is attached, or
if only 1 flatpanel and 1 analog display is attached, the port reversal is of
no consequence. However if 2 flatpanels are attached, it can cause display
problems.
There is no sane way of determining if the hardware reversed the i2c port
assignment, so the simplest fix is to add a boot/module option, "reverse_i2c
to explicitly reverse the i2c port.
This also restores i2c ordering back to the pre-2.6.22 state.
fbdev: find mode with the highest/safest refresh rate in fb_find_mode()
Currently, if the refresh rate is not specified, fb_find_mode() returns the
first known video mode with the requested resolution, which provides no
guarantees wrt the refresh rate. Change this so that the mode with the
highest refresh rate is returned when the driver provides a custom video mode
database and the monitor limits, and a mode with the safe 60 Hz refresh rate
otherwise.
Signed-off-by: Michal Januszewski <spock@gentoo.org> Signed-off-by: Antonino Daplas <adaplas@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ilya Yanok [Tue, 16 Oct 2007 08:29:17 +0000 (01:29 -0700)]
vfb: make virtual framebuffer mmapable
Changed things:
1. vmalloc()/vfree() replaced with rvmalloc()/rvfree() (taken from
drivers/media/video/se401.c)
2. mmap method implemented (mostly taken from drivers/media/video/se401.c)
3. smem_start and smem_len fields of struct fb_fix_screeninfo initialized.
(smem_start initialized with virtual address, don't know if it is really
bad...)
Krzysztof Helt [Tue, 16 Oct 2007 08:29:16 +0000 (01:29 -0700)]
pm2fb: panning and hardware cursor fixes
This patch:
- disallows setting of virtual height above 2048 as it does
not work for accelerated copyarea and imageblit
- fixes blinking of pm2v cursor by pushing cursor outside
the display (x=2047)
- fixes hardware cursor position on Permedia 2 chips with
panning enabled
- enables hardware cursor by default
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl> Signed-off-by: Antonino Daplas <adaplas@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Krzysztof Helt [Tue, 16 Oct 2007 08:29:13 +0000 (01:29 -0700)]
cirrusfb: code improvements
This patch does some "short-range" code improvements like merging identical
switch clauses, replacing conditional branches with calculation of values,
merging only once-used functions into place they are called from.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl> Signed-off-by: Antonino Daplas <adaplas@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Krzysztof Helt [Tue, 16 Oct 2007 08:29:05 +0000 (01:29 -0700)]
s3c2410fb: source code improvements
This patch:
- moves more display mode preparations to s3c2410fb_check_var()
- reduces number of fields in s3c2410fb_info
- removes redundant values setting in s3c2410fb_probe()
- removes static mach_info pointer
- releases fb_info structure in s3c2410fb_remove()
- changes s3c2410fb_init to __init from __devinit
- fixes few typos in comments and removes unused includes
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl> Signed-off-by: Antonino Daplas <adaplas@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Krzysztof Helt [Tue, 16 Oct 2007 08:29:04 +0000 (01:29 -0700)]
fbdev: change asm/uaccess.h to linux/uaccess.h
This patch replaces <asm/uaccess.h> with <linux/uaccess.h> after the
checkpatch.pl hint. The include of <asm/uaccess.h> is removed if the driver
does not use it.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl> Signed-off-by: Antonino Daplas <adaplas@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ralf Baechle [Tue, 16 Oct 2007 08:29:04 +0000 (01:29 -0700)]
vt: Fix warnings in selection.h
<linux/selection.h> assumes that struct tty_struct has previously been
included. If not, this pile of warnings will result:
CC [M] drivers/video/console/newport_con.o
In file included from drivers/video/console/newport_con.c:18:
include/linux/selection.h:16: warning: 'struct tty_struct' declared inside param
eter list
include/linux/selection.h:16: warning: its scope is only this definition or decl
aration, which is probably not what you want
include/linux/selection.h:17: warning: 'struct tty_struct' declared inside param
eter list
include/linux/selection.h:20: warning: 'struct tty_struct' declared inside param
eter list
Fixed by adding a forward declaration of struct tty_struct.
Ralf Baechle [Tue, 16 Oct 2007 08:29:03 +0000 (01:29 -0700)]
fbcon: Convert struct font_desc to use ISO C initializers
Akpm's patch "newport_con warning fix" got me to look at the console drivers
again and one thing that I noticed was that none of the fonts was using ISO
initializers for it's fonts.
Krzysztof Helt [Tue, 16 Oct 2007 08:29:02 +0000 (01:29 -0700)]
s3c2410fb: byte ordering fixes
This patch sets correct bits related to the byte ordering of the
framebuffer. This was tested on little endian kernel only. The big endian
kernel may require different settings.
The patch also adds 32 bpp mode which is called 24 bpp by Samsung. One
pixel takes 32 bits but only 24 bits are used in this mode.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl> Signed-off-by: Antonino Daplas <adaplas@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Krzysztof Helt [Tue, 16 Oct 2007 08:28:57 +0000 (01:28 -0700)]
s3c2410fb: add margin fields to s3c2410fb_display
This patch adds margins fields to the s3c2410fb_display
structure. It also sets display type and horizontal
margins in all platform files that use the s3c2410fb
driver.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl> Signed-off-by: Antonino Daplas <adaplas@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Krzysztof Helt [Tue, 16 Oct 2007 08:28:56 +0000 (01:28 -0700)]
s3c2410fb: multi-display support
This patch adds a new structure to describe and handle
more than one panel (display mode) for the s3c2410 framebuffer.
This structure is added after the pxafb driver.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl> Signed-off-by: Antonino Daplas <adaplas@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Krzysztof Helt [Tue, 16 Oct 2007 08:28:54 +0000 (01:28 -0700)]
s3c2410fb: code cleanup
This patch cleans up the driver a bit. It contains
coding style fixes (pointed by Lindent and checkpatch),
white space clean ups and few minor code improvements.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl> Signed-off-by: Antonino Daplas <adaplas@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Krzysztof Helt [Tue, 16 Oct 2007 08:28:53 +0000 (01:28 -0700)]
pm2fb: Permedia 2V hardware cursor support
This patch adds hardware cursor support for Permedia 2V chips.
The hardware cursor is disabled by default. It does not blink - the
same issue is mentioned in the x11 driver.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl> Signed-off-by: Antonino Daplas <adaplas@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
fbdev: Fix incorrect timings in some modedb entries
Reported by: John Lumby <johnlumby@hotmail.com>
Some of the entries in the mode database does not match the comments and/or
the refresh field. Adjust the timings so they match with both the comments
and the refresh rate.
Krzysztof Helt [Tue, 16 Oct 2007 08:28:45 +0000 (01:28 -0700)]
tdfxfb: 3 fixes
This patch fixes 3 issues:
- transparency handling in tdfxfb
- panning with more than 4096 virtual height and acceleration (acceleration
with x & y > 4096)
- exit paths on errors in tdfxfb_probe()
Additionally it sets a FBINFO_READS_FAST flag to use smart blitter scrolling
(speed up on tdfxfb).
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl> Signed-off-by: Antonino Daplas <adaplas@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hans J. Koch [Tue, 16 Oct 2007 08:28:41 +0000 (01:28 -0700)]
pxafb: Add support for other palette formats
This patch adds support for the other three palette formats possible with
the PXA LCD controller. This is required on boards where an LCD is connected
with all its 18 bits. With this patch, it's possible to use an 8-bit mode
with 18-bit palette entries. This used to be possible in 2.4 kernels but
disappeared in 2.6. With current kernels, you can only get wrong colours
out of an LCD connected this way.
Users can choose the palette format by doing something like this
in their board definition:
Raphael Assenat [Tue, 16 Oct 2007 08:28:40 +0000 (01:28 -0700)]
mbxfb: Improvements and new features
This contains the following changes:
* Overlay surface alpha is configured separately from the overlay. This
prevents display glitches (configure and fill the overlay first, set
alpha to a visible value next)
* Added an ioctl for configuring transparency of the Overlay and graphics
planes. Blend mode, colorkey mode and global alpha mode are supported.
* Added an ioctl for setting the plane order. The overlay plance can be placed
over or
under the graphics plane.
* Added an ioctl for setting and reading chip registers, with mask.
Ben Dooks [Tue, 16 Oct 2007 08:28:39 +0000 (01:28 -0700)]
sm501fb: Ensure panel interface is not tristated when setup
When we setup the panel interface whilst configuring the
framebuffer, we should ensure the panel interface is not
in tristate, in case the bootloader or previous setup has
not enabled it.
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Antonino Daplas <adaplas@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ben Dooks [Tue, 16 Oct 2007 08:28:37 +0000 (01:28 -0700)]
sm501fb: update suspend and resume code
The suspend and resume code is failing to restore the CRT control
register, thus causing the CRT data-path to get changed if the
SM501 experiences a reset over suspend.
Also move some of the debug messages to dev_dbg() level and ensure
that the suspend code does not try and restore anything it did not
manage to save.
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Antonino Daplas <adaplas@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Krzysztof Helt [Tue, 16 Oct 2007 08:28:36 +0000 (01:28 -0700)]
pm2fb: Permedia 2V initialization fixes
This patch:
- initializes correctly the Permedia2V chip if it is not initialized by BIOS
- puts back clock frequency for the ELSA WINNER board to 100kHz
- fixes returned error values from setcolreg() function
- uses more general classes for PCI ids
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl> Signed-off-by: Antonino Daplas <adaplas@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Krzysztof Helt [Tue, 16 Oct 2007 08:28:34 +0000 (01:28 -0700)]
pm2fb: source code improvements
This patch concentrates on source compacting, simplification and more
conformance to kernel coding standards.
The major changes:
- RD32() and WR() functions are merged into pm2_RD() and pm2_WR()
- conditional (with switch()) RDAC functions are separated in two
unconditional ones
- the conditional pm2fb_block_op() function is merged into pm2fb_fillrect()
and pm2fb_copyarea()
- WAIT_FIFO() values are corrected
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl> Signed-off-by: Antonino Daplas <adaplas@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Krzysztof Helt [Tue, 16 Oct 2007 08:28:32 +0000 (01:28 -0700)]
pm3fb: improvements and cleanups
This patch contains improvements:
- it adds ROP_XOR in pm3fb_fillrect()
- it conforms closer to coding style
- it removes redundant parentheses and setting bits with 0 value
- it checks if hardware acceleration is disabled in pm3fb_imageblit
- it adds module description
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl> Signed-off-by: Antonino Daplas <adaplas@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Krzysztof Helt [Tue, 16 Oct 2007 08:28:32 +0000 (01:28 -0700)]
pm3fb: 3 small fixes
This patch contains 3 small improvements:
- it corrects scan line width calculation in pm3fb_imageblit()
- it corrects mmio mapping for big endian machines
- it enables panning acceleration constants
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl> Signed-off-by: Antonino Daplas <adaplas@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Krzysztof Helt [Tue, 16 Oct 2007 08:28:31 +0000 (01:28 -0700)]
pm3fb: header file reduction
This patch removes constants named AAA_DISABLE with value 0. They are redudant
and misleading ( a |= AAA_DISABLE does nothing and usually should be
a &= ~AAA_ENABLE).
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl> Signed-off-by: Antonino Daplas <adaplas@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
uvesafb is an enhanced version of vesafb. It uses a userspace helper (v86d)
to execute calls to the x86 Video BIOS functions. The driver is not limited
to any specific arch and whether it works on a given arch or not depends on
that arch being supported by the userspace daemon. It has been tested on
x86_32 and x86_64.
A single BIOS call is represented by an instance of the uvesafb_ktask
structure. This structure contains a buffer, a completion struct and a
uvesafb_task substructure, containing the values of the x86 registers, a flags
field and a field indicating the length of the buffer. Whenever a BIOS call
is made in the driver, uvesafb_exec() builds a message using the uvesafb_task
substructure and the contents of the buffer. This message is then assigned a
random ack number and sent to the userspace daemon using the connector
interface.
The message's sequence number is used as an index for the uvfb_tasks array,
which provides a mapping from the messages coming from userspace to the
in-kernel uvesafb_ktask structs.
The userspace daemon performs the requested operation and sends a reply in the
form of a uvesafb_task struct and, optionally, a buffer. The seq and ack
numbers in the reply should be exactly the same as those in the request.
Each message from userspace is processed by uvesafb_cn_callback() and after
passing a few sanity checks leads to the completion of a BIOS call request.
Signed-off-by: Michal Januszewski <spock@gentoo.org> Signed-off-by: Antonino Daplas <adaplas@gmail.com> Cc: Paul Mundt <lethal@linux-sh.org> Cc: Paulo Marques <pmarques@grupopie.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bryan Kadzban [Tue, 16 Oct 2007 08:28:23 +0000 (01:28 -0700)]
rtc: allow validated RTC_PIE_ON for non-root
drivers/char/rtc.c allowed RTC_PIE_ON ioctls for non-root users, as long as
the current interval (set via RTC_IRQP_SET) is <= max_user_freq. Allow
RTC_PIE_ON under the same conditions when /dev/rtc* is handled by the rtc
subsystem.
Signed-off-by: Bryan Kadzban <bryan@kdzbn.homelinux.net> Acked-by: Alessandro Zummo <alessandro.zummo@towertech.it> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bryan Kadzban [Tue, 16 Oct 2007 08:28:22 +0000 (01:28 -0700)]
rtc: add max_user_freq to sysfs
drivers/char/rtc.c exposed a sysctl to change the maximum frequency at
which a non-root user could ask the RTC to generate interrupts (via the
RTC_IRQP_SET ioctl). This value is no longer available under the new RTC
subsystem, so add it to sysfs for each RTC device.
Works for me on x86_64 (both reads and writes), using rtc-cmos.
Signed-off-by: Bryan Kadzban <bryan@kdzbn.homelinux.net> Acked-by: Alessandro Zummo <a.zummo@towertech.it> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mark Lord [Tue, 16 Oct 2007 08:28:21 +0000 (01:28 -0700)]
rtc: fix readback from /sys/class/rtc/rtc?/wakealarm
Fix readback of RTC alarms on platforms which return -1 in
non-hardware-supported RTC alarm fields.
To fill in the missing (-1) values, we grab an RTC timestamp along with the
RTC alarm value, and use the timestamp fields to populate the missing alarm
fields.
To counter field-wrap races (since the timestamp and alarm are not read
together atomically), we read the RTC timestamp both before and after
reading the RTC alarm value, and then check for wrapped fields --> if any
have wrapped, we know we have a possible inconsistency, so we loop and
reread the timestamp and alarm again.
Wrapped fields in the RTC timestamps are an issue because rtc-cmos.c, for
example, also gets/uses an RTC timestamp internally while fetching the RTC
alarm. If our timestamp here wasn't the same (minutes and higher) as what
was used internally there, then we might end up populating the -1 fields
with inconsistent values.
This fixes readbacks from /sys/class/rtc/rtc?/wakealarm, as well as other
code paths which call rtc_read_alarm().
Signed-off-by: Mark Lord <mlord@pobox.com> Cc: David Brownell <david-b@pacbell.net> Cc: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jean Delvare [Tue, 16 Oct 2007 08:28:18 +0000 (01:28 -0700)]
rtc-pcf8583: Check for i2c adapter functionality
Not all i2c adapters support I2C-level messaging. Check that the adapter
does before probing for a PCF8583 chip, as the driver makes use of
i2c_transfer and i2c_master_send.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Atsushi Nemoto [Tue, 16 Oct 2007 08:28:18 +0000 (01:28 -0700)]
rtc: make rtc-ds1742 driver hotplug-aware
The rtc-ds1742 platform driver name doesn't match its module name,
which might prevents it from properly hotplugging. There is only two
in-tree user of its driver, which are fixed by this patch too.
Mark Zhan [Tue, 16 Oct 2007 08:28:17 +0000 (01:28 -0700)]
rtc-dev: no need to convert file->private_data to rtc device
In rtc-dev.c, when a rtc device is opened, file->private_data is already
attached with the rtc device pointer, so there is no need to call
to_rtc_device() to convert file->private_data to a rtc device pointer.
Acked-by: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: Mark Zhan <rongkai.zhan@windriver.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Brownell [Tue, 16 Oct 2007 08:28:16 +0000 (01:28 -0700)]
rtc_irq_set_freq() requires power-of-two and associated kerneldoc
RTC periodic IRQs are only defined to work for 2^N Hz values. This patch
moves that validity check into the infrastructure, so drivers don't need to
check it; and adds kerneldoc for the two interface functions related to
periodic IRQs. (One of which was quite mysterious until its first use was
recently checked in!)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michael Halcrow [Tue, 16 Oct 2007 08:28:14 +0000 (01:28 -0700)]
ecryptfs: clean up page flag handling
The functions that eventually call down to ecryptfs_read_lower(),
ecryptfs_decrypt_page(), and ecryptfs_copy_up_encrypted_with_header()
should have the responsibility of managing the page Uptodate
status. This patch gets rid of some of the ugliness that resulted from
trying to push some of the page flag setting too far down the stack.
Signed-off-by: Michael Halcrow <mhalcrow@us.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michael Halcrow [Tue, 16 Oct 2007 08:28:11 +0000 (01:28 -0700)]
eCryptfs: convert mmap functions to use persistent file
Convert readpage, prepare_write, and commit_write to use read_write.c
routines. Remove sync_page; I cannot think of a good reason for implementing
that in eCryptfs.
Signed-off-by: Michael Halcrow <mhalcrow@us.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michael Halcrow [Tue, 16 Oct 2007 08:28:10 +0000 (01:28 -0700)]
eCryptfs: make open, truncate, and setattr use persistent file
Rather than open a new lower file for every eCryptfs file that is opened,
truncated, or setattr'd, instead use the existing lower persistent file for
the eCryptfs inode. Change truncate to use read_write.c functions. Change
ecryptfs_getxattr() to use the common ecryptfs_getxattr_lower() function.
Signed-off-by: Michael Halcrow <mhalcrow@us.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michael Halcrow [Tue, 16 Oct 2007 08:28:10 +0000 (01:28 -0700)]
eCryptfs: update metadata read/write functions
Update the metadata read/write functions and grow_file() to use the
read_write.c routines. Do not open another lower file; use the persistent
lower file instead. Provide a separate function for
crypto.c::ecryptfs_read_xattr_region() to get to the lower xattr without
having to go through the eCryptfs getxattr.
Signed-off-by: Michael Halcrow <mhalcrow@us.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michael Halcrow [Tue, 16 Oct 2007 08:28:07 +0000 (01:28 -0700)]
eCryptfs: read_write.c routines
Add a set of functions through which all I/O to lower files is consolidated.
This patch adds a new inode_info reference to a persistent lower file for each
eCryptfs inode; another patch later in this series will set that up. This
persistent lower file is what the read_write.c functions use to call
vfs_read() and vfs_write() on the lower filesystem, so even when reads and
writes come in through aops->readpage and aops->writepage, we can satisfy them
without resorting to direct access to the lower inode's address space.
Several function declarations are going to be changing with this patchset.
For now, in order to keep from breaking the build, I am putting dummy
parameters in for those functions.
Signed-off-by: Michael Halcrow <mhalcrow@us.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / linux-2.6 / log