Sergei Shtylyov [Wed, 7 Feb 2007 17:18:37 +0000 (18:18 +0100)]
pdc202xx_new: remove useless code
Remove the following useless fragments from the driver:
- the ide_dma_lostirq() and ide_dma_timeout() handlers which boil down to just
printing the incoherent reset message and calling their default counterparts;
- check for non-NULL drive->id in the ide_dma_check() handler -- this is assumed
to be true by all other handlers (also, get rid of unnecessary nesting of the
conditional statements there);
- the comment before pdcnew_tune_drive() which has nothing to do with the code.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Sergei Shtylyov [Wed, 7 Feb 2007 17:18:25 +0000 (18:18 +0100)]
piix: fix 82371MX enablebits
According to the datasheet, Intel 82371MX (MPIIX) actually has only a
single IDE channel mapped to the primary or secondary ports depending on
the value of the bit 14 of the IDETIM register at PCI config. offset 0x6C
(the register at 0x6F which the driver refers to. doesn't exist). So,
disguise the controller as dual channel and set enablebits masks/values
such that only either primary or secondary channel is detected enabled.
Also, preclude the IDE probing code from reading PCI BARs, this controller
just doesn't have them (it's not the separate PCI function like the other
PCI controllers), it only decodes the legacy addresses.
[ Alan sayeth " MPIIX does not work with or without the change. It needs its
own different driver and not to use setup-pci. Huge job and since it works
well with libata who cares. Ditto the early PIIX chip." ]
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Sergei Shtylyov [Wed, 7 Feb 2007 17:18:20 +0000 (18:18 +0100)]
hpt366: HPT36x PCI clock detection fix
Fix minor coding mistake in the HPT36x PCI clock detection code noticed by
Bartlomiej Zolnierkiewicz -- it always reported 33 MHz due to the missing
'break' statements. This, however, most probably never mattered -- in fact, I
was thinking of removing the 25/40 MHz cases completely since HPT36x BIOSes
didn't seem to set any other value than 7 into the 'cmd_high_time' field, i.e.
supported only 33 MHz PCI.
Note that in the original driver there was another bug: 25 and 40 MHz cases
were interchanged. Since the 'cmd_high_time' field is in units of PCI clocks,
a lower clock count just *cannot* correspond to a higher frequency, i. e. it
should be 5 for 25 MHz PCI and 9 for 40 MHz PCI, not the other way around.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Sergei Shtylyov [Wed, 7 Feb 2007 17:18:16 +0000 (18:18 +0100)]
hpt366: init code rewrite
Finally, rework the driver init. code to correctly handle all the chip
variants HighPoint has created so far. This should cure the rest of the
timing issues in the driver (especially, on 66 MHz PCI) caused by the
HighPoint's habit of switching the base DPLL clock with every new revision
of the chips...
- switch to using the enumeration type to differ between the numerous chip
variants, matching PCI device/revision ID with the chip type early, at the
init_setup stage;
- extend the hpt_info structure to hold the DPLL and PCI clock frequencies,
stop duplicating it for each channel by storing the pointer in the pci_dev
structure: first, at the init_setup stage, point it to a static "template"
with only the chip type and its specific base DPLL frequency, the highest
supported DMA mode, and the chip settings table pointer filled, then, at
the init_chipset stage, allocate per-chip instance and fill it with the
rest of the necessary information;
- get rid of the constant thresholds in the HPT37x PCI clock detection code,
switch to calculating PCI clock frequency based on the chip's base DPLL
frequency;
- switch to using the DPLL clock and enable UltraATA/133 mode by default on
anything newer than HPT370/A;
- fold PCI clock detection and DPLL setup code into init_chipset_hpt366(),
unify the HPT36x/37x setup code and the speedproc handlers by joining the
register setting lists into the table indexed by the clock selected;
- add enablebits for all the chips to avoid touching disabled channels
(though the HighPoint BIOS seem to only disable the primary one on
HPT371/N);
- separate the UltraDMA and MWDMA masks there to avoid changing PIO timings
when setting an UltraDMA mode in hpt37x_tune_chipset().
This version has been tested on HPT370/302/371N.
Thanks to Alan for the inspiration. Hopefully, his libata driver will also
benefit from the work done on this "obsolete" driver...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Sergei Shtylyov [Wed, 7 Feb 2007 17:18:13 +0000 (18:18 +0100)]
hpt366: clean up DMA timeout handling for HPT370
Clean up DMA timeout handling for HPT370:
- hpt370_lostirq_timeout() cleared the DMA status which made __ide_dma_end()
called afterwards return the incorrect result, and the DMA engine was reset
both before and after stopping DMA while the HighPoint drivers only do it
after (which seems logical) -- fix this and also rename the function;
- get rid of the needless mutual recursion in hpt370_ide_dma_end() and
hpt370_ide_dma_timeout();
- get rid of hpt370_lostirq_timeout() since hwif->ide_dma_end() called from
the driver's interrupt handler later does all its work.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Sergei Shtylyov [Wed, 7 Feb 2007 17:18:11 +0000 (18:18 +0100)]
hpt366: merge HPT37x speedproc handlers
Continue with the driver rewrite:
- move the interrupt twiddling code from the speedproc handlers into the
init_hwif_hpt366 which allows to merge the two HPT37x speedproc handlers
into one;
- get rid of in init_hpt366 which solely consists of the duplicate code, then
fold init_hpt37x() into init_chipset_hpt366();
- fix hpt3xx_tune_drive() to always set the PIO mode requested, not the best
possible one, change hpt366_config_drive_xfer_rate() accordingly, simplify
it a bit;
- group all the DMA related code together init_hwif_hpt366(), and generally
clean up and beautify it.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Sergei Shtylyov [Wed, 7 Feb 2007 17:17:54 +0000 (18:17 +0100)]
hpt366: switch to using pci_get_slot
Switch to using pci_get_slot() to get to the function 1 of HPT36x/374 chips --
there's no need for the driver itself to walk the list of the PCI devices, and
it also forgets to check the bus number of the device found.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Sergei Shtylyov [Wed, 7 Feb 2007 17:17:37 +0000 (18:17 +0100)]
hpt366: rework rate filtering
- Rework hpt3xx_ratemask() and hpt3xx_ratefilter() so that the former
returns the max. mode computed at the load time and doesn't have to do
bad Ultra33 drive list lookups anymore; remove the duplicate code from
the latter function. Move the quirky drive list lookup into
hpt3xx_quirkproc() where it should have been from the start...
- Disable UltraATA/100 for HPT370 by default as the 33 MHz ATA clock
being used does not allow for it, and this *greatly* increases the
transfer speed.
- Save some space by using byte-wide fields in struct hpt_info; switch to
reading the 8-bit PCI revision ID reg. only, not the whole 32-bit reg.
- Start incrementing the driver version number with each patch (should
have been done from the first one posted).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Linus Torvalds [Wed, 7 Feb 2007 01:24:58 +0000 (17:24 -0800)]
Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6: (27 commits)
[IA64] swiotlb abstraction (e.g. for Xen)
[IA64] swiotlb cleanup
[IA64] make swiotlb use bus_to_virt/virt_to_bus
[IA64] swiotlb bug fixes
[IA64] Hook up getcpu system call for IA64
[IA64] clean up sparsemem memory_present call
[IA64] show_mem() for IA64 sparsemem NUMA
[IA64] missing exports hwsw_sync_...
[IA64] virt_to_page() can be called with NULL arg
[IA64] alignment bug in ldscript
[IA64] register memory ranges in a consistent manner
[IA64] Enable SWIOTLB only when needed
[IA64-SGI] Check for TIO errors on shub2 Altix
[IA64] remove bogus prototype ia64_esi_init()
[IA64] Clear IRQ affinity when unregistered
[IA64] fix ACPI Kconfig issues
[IA64] Fix NULL-pointer dereference in ia64_machine_kexec()
[IA64] find thread for user rbs address
[IA64] use snprintf() on features field of /proc/cpuinfo
[IA64] enable singlestep on system call
...
Linus Torvalds [Tue, 6 Feb 2007 22:56:37 +0000 (14:56 -0800)]
Merge branch 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jikos/hid
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jikos/hid:
USB HID: handle multi-interface devices for Apple macbook pro properly
HID: move away from DEBUG defines in favor of CONFIG_HID_DEBUG
USB HID: fix bogus comment in hid_get_class_descriptor()
USB HID: remove hid_find_field_by_usage()
HID: API - fix leftovers of hidinput API in USB HID
HID: hid debug from hid-debug.h to hid layer
hid: force feedback driver for PantherLord USB/PS2 2in1 Adapter
hid: quirk for multi-input devices with unneeded output reports
hid: allow force feedback for multi-input devices
Linus Torvalds [Tue, 6 Feb 2007 22:55:33 +0000 (14:55 -0800)]
Merge branch 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IB/ehca: Remove obsolete prototypes
IB/ehca: Remove use of do_mmap()
RDMA/addr: Handle ethernet neighbour updates during route resolution
IB: Make sure struct ib_user_mad.data is aligned
IB/srp: Don't wait for response when QP is in error state.
IB: Return qp pointer as part of ib_wc
IB: Include <linux/kref.h> explicitly in <rdma/ib_verbs.h>
Linus Torvalds [Tue, 6 Feb 2007 22:54:54 +0000 (14:54 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc: (32 commits)
mmc: tifm: replace kmap with page_address
mmc: sdhci: fix voltage ocr
mmc: sdhci: replace kmap with page_address
mmc: wbsd: replace kmap with page_address
mmc: handle pci_enable_device() return value in sdhci
mmc: Proper unclaim in mmc_block
mmc: change wbsd mailing list
mmc: Graceful fallback for fancy features
mmc: Handle wbsd's stupid command list
mmc: Allow host drivers to specify max block count
mmc: Allow host drivers to specify a max block size
tifm_sd: add suspend and resume functionality
tifm_core: add suspend/resume infrastructure for tifm devices
tifm_7xx1: prettify
tifm_7xx1: recognize device 0xac8f as supported
tifm_7xx1: switch from workqueue to kthread
tifm_7xx1: Merge media insert and media remove functions
tifm_7xx1: simplify eject function
Add dummy_signal_irq function to save check in ISR
Remove unused return value from signal_irq callback
...
David Howells [Tue, 6 Feb 2007 13:45:51 +0000 (13:45 +0000)]
[PATCH] Keys: Fix key serial number collision handling
Fix the key serial number collision avoidance code in key_alloc_serial().
This didn't use to be so much of a problem as the key serial numbers were
allocated from a simple incremental counter, and it would have to go through
two billion keys before it could possibly encounter a collision. However, now
that random numbers are used instead, collisions are much more likely.
This is fixed by finding a hole in the rbtree where the next unused serial
number ought to be and using that by going almost back to the top of the
insertion routine and redoing the insertion with the new serial number rather
than trying to be clever and attempting to work out the insertion point
pointer directly.
This fixes kernel BZ #7727.
Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
[CIFS] Minor cleanup
[CIFS] Missing free in error path
[CIFS] Reduce cifs stack space usage
[CIFS] lseek polling returned stale EOF
Linus Torvalds [Tue, 6 Feb 2007 22:35:30 +0000 (14:35 -0800)]
Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (40 commits)
[MIPS] Yosemite: Fix missing parens in SERIAL_READ_1 macro
[MIPS] Fix warnings in run_uncached on 32bit kernel
[MIPS] Comment fix
[MIPS] MT: Nuke duplicate mips_mt_regdump() prototype.
[MIPS] Alchemy: Fix PCI-memory access
[MIPS] Move .set reorder out of conditional code
[MIPS] Check FCSR for pending interrupts before restoring from a context.
[MIPS] Jaguar ATX: Fix large number of warnings.
[MIPS] Jaguar: Fix MAC address detection after platform_device conversion.
[MIPS] SMTC: Make a bunch of functions and variables static.
[MIPS] Use compat_sys_pselect6
[MIPS] SMTC: Cleanup idle hook invocation.
[MIPS] SELinux: Add security hooks to mips-mt {get,set}affinity
[MIPS] IRIX: Linux coding style cleanups.
[MIPS] PB1100: Fix pile of warnings
[MIPS] Alchemy: Fix bunch of warnings
[MIPS] Whitespace cleanups.
[MIPS] Alchemy: Fix bunch more warnings.
[MIPS] Use ARRAY_SIZE macro when appropriate
[MIPS] Fix some whitespace damage
...
Oleg Verych [Tue, 6 Feb 2007 01:18:22 +0000 (02:18 +0100)]
[PATCH] kbuild: correctly skip tilded backups in localversion files
Tildes as in path as in filenames are handled correctly now:
only files, containing tilde '~', are backups, thus are not valid.
[KJ]:
Definition of `space' was removed, scripts/Kbuild.include has one.
That definition was taken right from the GNU make manual, while Kbuild's
version is original.
Cc: Roman Zippel <zippel@linux-m68k.org> Cc: Bastian Blank <bastian@waldi.eu.org> Cc: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Oleg Verych <olecom@flower.upol.cz> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Oleg Verych [Tue, 6 Feb 2007 01:18:20 +0000 (02:18 +0100)]
[PATCH] kbuild scripts: replace gawk, head, bc with shell, update
Replacing overhead of using some (external) programs
instead of good old `sh'.
Cc: Roman Zippel <zippel@linux-m68k.org> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: William Stearns <wstearns@pobox.com> Cc: Martin Schlemmer <azarah@nosferatu.za.org> Signed-off-by: Oleg Verych <olecom@flower.upol.cz> Acked-by: Mark Lord <lkml@rtr.ca> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Yoichi Yuasa [Tue, 6 Feb 2007 01:59:22 +0000 (10:59 +0900)]
[MIPS] Fix warnings in run_uncached on 32bit kernel
arch/mips/lib/uncached.c: In function 'run_uncached':
arch/mips/lib/uncached.c:47: warning: comparison is always true due to limited range of data type
arch/mips/lib/uncached.c:48: warning: comparison is always false due to limited range of data type
arch/mips/lib/uncached.c:57: warning: comparison is always true due to limited range of data type
arch/mips/lib/uncached.c:58: warning: comparison is always false due to limited range of data type
Alexander Bigga [Thu, 21 Dec 2006 10:25:19 +0000 (11:25 +0100)]
[MIPS] Alchemy: Fix PCI-memory access
The problem was introduced in 2.6.18.3 with the casting of some
36bit-defines (PCI memory) in au1000.h to resource_size_t which may be
u32 or u64 depending on the experimental CONFIG_RESOURCES_64BIT.
With unset CONFIG_RESOURCES_64BIT, the pci-memory cannot be accessed
because the ioremap in arch/mips/au1000/common/pci.c already used the
truncated addresses.
With set CONFIG_RESOURCES_64BIT, things get even worse, because PCI-scan
aborts, due to resource conflict: request_resource() in arch/mips/pci/pci.c
fails because the maximum iomem-address is 0xffffffff (32bit) but the
pci-memory-start-address is 0x440000000 (36bit).
To get pci working again, I propose the following patch:
1. remove the resource_size_t-casting from au1000.h again
2. make the casting in arch/mips/au1000/common/pci.c (it's allowed and
necessary here. The 36bit-handling will be done in __fixup_bigphys_addr).
With this patch pci works again like in 2.6.18.2, the gcc-compile warnings
in pci.c are gone and it doesn't depend on CONFIG_EXPERIMENTAL.
Signed-off-by: Alexander Bigga <ab@mycable.de> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Quigley [Wed, 28 Jun 2006 13:36:46 +0000 (09:36 -0400)]
[MIPS] SELinux: Add security hooks to mips-mt {get,set}affinity
This patch adds LSM hooks into the setaffinity and getaffinity functions
for the mips architecture to enable security modules to control these
operations between tasks with different security attributes. This
implementation uses the existing task_setscheduler and task_getscheduler
LSM hooks.
Signed-Off-By: David Quigley <dpquigl@tycho.nsa.gov> Acked-by: Stephen Smalley <sds@tycho.nsa.gov> Signed-off-by: James Morris <jmorris@namei.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Tue, 7 Nov 2006 10:19:05 +0000 (10:19 +0000)]
[MIPS] PB1100: Fix pile of warnings
CC arch/mips/au1000/pb1100/board_setup.o
arch/mips/au1000/pb1100/board_setup.c: In function ‘board_setup’:
arch/mips/au1000/pb1100/board_setup.c:104: warning: passing argument 1 of ‘readb’ makes pointer from integer without a cast
arch/mips/au1000/pb1100/board_setup.c:105: warning: passing argument 1 of ‘readb’ makes pointer from integer without a cast
arch/mips/au1000/pb1100/board_setup.c:105: warning: passing argument 2 of ‘writeb’ makes pointer from integer without a cast
arch/mips/au1000/pb1100/board_setup.c:109: warning: passing argument 1 of ‘readb’ makes pointer from integer without a cast
arch/mips/au1000/pb1100/board_setup.c:110: warning: passing argument 1 of ‘readb’ makes pointer from integer without a cast
arch/mips/au1000/pb1100/board_setup.c:110: warning: passing argument 2 of ‘writeb’ makes pointer from integer without a cast
arch/mips/au1000/pb1100/board_setup.c:51: warning: unused variable ‘sys_clksrc’
arch/mips/au1000/pb1100/board_setup.c:51: warning: unused variable ‘sys_freqctrl’
arch/mips/au1000/pb1100/board_setup.c:50: warning: unused variable ‘pin_func’
Ralf Baechle [Tue, 7 Nov 2006 09:58:30 +0000 (09:58 +0000)]
[MIPS] Alchemy: Fix bunch of warnings
CC arch/mips/au1000/common/pci.o
arch/mips/au1000/common/pci.c:42: warning: large integer implicitly truncated to unsigned type
arch/mips/au1000/common/pci.c:43: warning: large integer implicitly truncated to unsigned type
arch/mips/au1000/common/pci.c:49: warning: large integer implicitly truncated to unsigned type
arch/mips/au1000/common/pci.c:50: warning: large integer implicitly truncated to unsigned type
arch/mips/au1000/common/pci.c: In function ‘au1x_pci_setup’:
arch/mips/au1000/common/pci.c:82: warning: ISO C90 forbids mixed declarations and code
Atsushi Nemoto [Tue, 16 Jan 2007 14:29:11 +0000 (23:29 +0900)]
[MIPS] Kconfig: Move some entries to appropriate menu
Currently KEXEC is in "Machine selection", SECCOMP, PM, APM are in
"Executable file formats" menu. Move KEXEC and SECCOMP to "Kernel
type" and PM, APM to new "Power management options" menu. Also
replace "config PM" with kernel/power/Kconfig.
Franck Bui-Huu [Wed, 10 Jan 2007 08:44:05 +0000 (09:44 +0100)]
[MIPS] FLATMEM: introduce PHYS_OFFSET.
The old code was assuming that min_low_pfn was always 0. This
means that platforms having a big hole at their memory start
paid the price of wasting some memory for the allocation of
unused entries in mem_map[].
This patch prevents this waste.
It introduces PHYS_OFFSET define which is the start of the
physical memory and uses it wherever needed. Specially when
converting physical/virtual addresses into virtual/physical
ones.
Franck Bui-Huu [Wed, 10 Jan 2007 08:44:04 +0000 (09:44 +0100)]
[MIPS] Setup min_low_pfn/max_low_pfn correctly
This patch makes a better usage of these two globals.
'min_low_pfn' is now correctly setup for all configs, which
allow us to rely on it in boot memory code init.
Atsushi Nemoto [Fri, 29 Dec 2006 15:43:59 +0000 (00:43 +0900)]
[MIPS] prom_free_prom_memory cleanup
Current prom_free_prom_memory() implementations are almost same as
free_init_pages(), or no-op. Make free_init_pages() extern (again)
and make prom_free_prom_memory() use it.
Atsushi Nemoto [Sun, 14 Jan 2007 14:41:42 +0000 (23:41 +0900)]
[MIPS] Make I8259A_IRQ_BASE customizable
Move I8259A_IRQ_BASE from asm/i8259.h to asm/mach-generic/irq.h and
make it really customizable. And remove I8259_IRQ_BASE declared on
some platforms. Currently only NEC_CMBVR4133 is using custom
I8259A_IRQ_BASE value.
Atsushi Nemoto [Sun, 7 Jan 2007 17:14:29 +0000 (02:14 +0900)]
[MIPS] Define MIPS_CPU_IRQ_BASE in generic header
The irq_base for {mips,rm7k,rm9k}_cpu_irq_init() are constant on all
platforms and are same value on most platforms (0 or 16, depends on
CONFIG_I8259). Define them in asm-mips/mach-generic/irq.h and make
them customizable. This will save a few cycle on each CPU interrupt.
A good side effect is removing some dependencies to MALTA in generic
SMTC code.
Although MIPS_CPU_IRQ_BASE is customizable, this patch changes irq
mappings on DDB5477, EMMA2RH and MIPS_SIM, since really customizing
them might cause some header dependency problem and there seems no
good reason to customize it. So currently only VR41XX is using custom
MIPS_CPU_IRQ_BASE value, which is 0 regardless of CONFIG_I8259.
Testing this patch on those platforms is greatly appreciated. Thank
you.
Jan Beulich [Tue, 6 Feb 2007 02:53:04 +0000 (18:53 -0800)]
[IA64] swiotlb abstraction (e.g. for Xen)
Add abstraction so that the file can be used by environments other than IA64
and EM64T, namely for Xen.
Signed-off-by: Jan Beulich <jbeulich@novell.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Tony Luck <tony.luck@intel.com>
Jan Beulich [Tue, 6 Feb 2007 02:51:25 +0000 (18:51 -0800)]
[IA64] swiotlb cleanup
- add proper __init decoration to swiotlb's init code (and the code calling
it, where not already the case)
- replace uses of 'unsigned long' with dma_addr_t where appropriate
- do miscellaneous simplicfication and cleanup
Signed-off-by: Jan Beulich <jbeulich@novell.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Tony Luck <tony.luck@intel.com>
Jan Beulich [Tue, 6 Feb 2007 02:49:45 +0000 (18:49 -0800)]
[IA64] make swiotlb use bus_to_virt/virt_to_bus
Convert all phys_to_virt/virt_to_phys uses to bus_to_virt/virt_to_bus, as is
what is meant and what is needed in (at least) some virtualized environments
like Xen.
Signed-off-by: Jan Beulich <jbeulich@novell.com> Acked-by: Muli Ben-Yehuda <muli@il.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Tony Luck <tony.luck@intel.com>
Jan Beulich [Tue, 6 Feb 2007 02:46:40 +0000 (18:46 -0800)]
[IA64] swiotlb bug fixes
This patch fixes
- marking I-cache clean of pages DMAed to now only done for IA64
- broken multiple inclusion in include/asm-x86_64/swiotlb.h
- missing call to mark_clean in swiotlb_sync_sg()
- a (perhaps only theoretical) issue in swiotlb_dma_supported() when
io_tlb_end is exactly at the end of memory
Signed-off-by: Jan Beulich <jbeulich@novell.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Tony Luck <tony.luck@intel.com>
George Beshers [Tue, 6 Feb 2007 00:20:04 +0000 (16:20 -0800)]
[IA64] show_mem() for IA64 sparsemem NUMA
On the ia64 architecture only this patch upgrades show_mem() for sparse
memory to be the same as it was for discontig memory. It has been shown to
work on NUMA and flatmem architectures.
Signed-off-by: George Beshers <gbeshers@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Tony Luck <tony.luck@intel.com>
Jan Beulich [Tue, 6 Feb 2007 00:20:03 +0000 (16:20 -0800)]
[IA64] missing exports hwsw_sync_...
Add missing exports to allow several drivers to be built as module with
CONFIG_IA64_HP_ZX1_SWIOTLB.
Signed-off-by: Jan Beulich <jbeulich@novell.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Tony Luck <tony.luck@intel.com>
Kirill Korotaev [Tue, 6 Feb 2007 00:19:59 +0000 (16:19 -0800)]
[IA64] alignment bug in ldscript
Occasionally the FSYS_RETURN patch list can have an odd length, causing other
data structures to get out of alignment. In OpenVZ it is odd and we get
misaligned kernel image, which does not boot.
Signed-off-by: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru> Signed-off-by: Kirill Korotaev <dev@openvz.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Tony Luck <tony.luck@intel.com>
Bob Picco [Tue, 30 Jan 2007 10:11:09 +0000 (02:11 -0800)]
[IA64] register memory ranges in a consistent manner
While pursuing and unrelated issue with 64Mb granules I noticed a problem
related to inconsistent use of add_active_range. There doesn't appear any
reason to me why FLATMEM versus DISCONTIG_MEM should register memory to
add_active_range with different code. So I've changed the code into a
common implementation.
The other subtle issue fixed by this patch was calling add_active_range in
count_node_pages before granule aligning is performed. We were lucky with
16MB granules but not so with 64MB granules. count_node_pages has reserved
regions filtered out and as a consequence linked kernel text and data
aren't covered by calls to count_node_pages. So linked kernel regions
wasn't reported to add_active_regions. This resulted in free_initmem
causing numerous bad_page reports. This won't occur with this patch
because now all known memory regions are reported by
register_active_ranges.
Acked-by: Mel Gorman <mel@csn.ul.ie> Signed-off-by: Bob Picco <bob.picco@hp.com> Acked-by: Simon Horman <horms@verge.net.au> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Tony Luck <tony.luck@intel.com>
Alex Williamson [Thu, 25 Jan 2007 05:48:04 +0000 (22:48 -0700)]
[IA64] Clear IRQ affinity when unregistered
When we offline a CPU, migrate_irqs() tries to determine whether the
affinity bits of the IRQ descriptor match any of the remaining online
CPUs. If not, it fixes up the interrupt to point somewhere else.
Unfortunately, if an IRQ is unregistered the IRQ descriptor may still
have affinity to the CPU being offlined, but the no_irq_chip handler
doesn't provide a set_affinity function. This causes us to hit the
WARN_ON in migrate_irqs().
The easiest solution seems to be setting all the bits in the affinity
mask when the last interrupt is removed from the vector. I hit this on
an older kernel with Xen/ia64 using driver domains (so it probably needs
more testing on upstream). Xen essentially uses the bind/unbind
interface in sysfs to unregister a device from a driver and thus
unregister the interrupt.
Signed-off-by: Alex Williamson <alex.williamson@hp.com> Signed-off-by: Tony Luck <tony.luck@intel.com>
Len Brown [Fri, 26 Jan 2007 05:38:53 +0000 (00:38 -0500)]
[IA64] fix ACPI Kconfig issues
All IA64 systems except IA64_HP_SIM include ACPI and PCI.
So prevent IA64 Kconfigs that try to do irritating things like building
PCI without building ACPI.
Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Tony Luck <tony.luck@intel.com>
Bernhard Walle [Sun, 28 Jan 2007 12:47:02 +0000 (13:47 +0100)]
[IA64] Fix NULL-pointer dereference in ia64_machine_kexec()
This patch fixes a NULL-pointer dereference in ia64_machine_kexec().
The variable ia64_kimage is set in machine_kexec_prepare() which is
called from sys_kexec_load(). If kdump wasn't configured before,
ia64_kimage is NULL. machine_kdump_on_init() passes ia64_kimage() to
machine_kexec() which assumes a valid value.
The patch also adds a few sanity checks for the image to simplify
debugging of similar problems in future.
Signed-off-by: Bernhard Walle <bwalle@suse.de> Signed-off-by: Tony Luck <tony.luck@intel.com>
bibo,mao [Tue, 30 Jan 2007 03:02:19 +0000 (11:02 +0800)]
[IA64] find thread for user rbs address
I encountered one problem when running ptrace test case the situation
is this: traced process's syscall parameter needs to be accessed, but
for sys_clone system call with clone_flag (CLONE_VFORK | CLONE_VM |
SIGCHLD) parameter. This syscall's parameter accessing result is wrong.
The reason is that vforked child process mm point is the same, but
tgid is different. Without this patch find_thread_for_addr will return
vforked process if vforked process is also stopped, but not the thread
which calls vfork syscall.
Aron Griffis [Mon, 5 Feb 2007 21:54:31 +0000 (13:54 -0800)]
[IA64] use snprintf() on features field of /proc/cpuinfo
Some patches have turned up on xen-devel recently to convert strcpy()
to safer alternatives and so forth. While reviewing those patches
I noticed that the features string building could be cleaned up.
This patch uses snprintf() instead of strcpy() and direct character
pointer manipulation. It makes the features string building safe and
gets rid of the special case for features output in show_cpuinfo()
Additionally I removed the (int) cast of ARRAY_SIZE, which seems to
serve no purpose.
Signed-off-by: Aron Griffis <aron@hp.com> Signed-off-by: Tony Luck <tony.luck@intel.com>
bibo,mao [Wed, 31 Jan 2007 09:50:31 +0000 (17:50 +0800)]
[IA64] enable singlestep on system call
As is pointed out in
http://www.gelato.org/community/view_linear.php?id=1_1036&from=authors&value=Ian%20Wienand#1_1039,
if single step on break instruction, the break fault has higher
priority than the single-step trap. When the break fault handler
is entered, it advances the IP by 1 instruction so break instruction
single-stepping is skipped, actually it is next instruction which
is single stepped.
This patch modifies this, it adds TIF_SINGLESTEP bit for thread
flags, and generate a fake sigtrap when single stepping break
instruction. Test case in attachment can verify this. Any comments
is welcome.
Signed-off-by: bibo, mao <bibo.mao@intel.com> Signed-off-by: Tony Luck <tony.luck@intel.com>
Horms [Mon, 5 Feb 2007 21:49:10 +0000 (13:49 -0800)]
[IA64] kexec: Move machine_shutdown from machine_kexec.c to process.c
This moves the ia64 implementation of machine_shutdown() from
machine_kexec.c to process.c, which is in keeping with the implelmentation
on other architectures, and seems like a much more appropriate home for it.
Signed-off-by: Simon Horman <horms@verge.net.au> Signed-off-by: Tony Luck <tony.luck@intel.com>
Heiko Carstens [Mon, 5 Feb 2007 20:18:41 +0000 (21:18 +0100)]
[S390] Mark kernel text section read-only.
Set read-only flag in the page table entries for the kernel image text
section. This will catch all instruction caused corruptions withing the
text section.
Instruction replacement via kprobes still works, since it bypasses now
dynamic address translation.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Heiko Carstens [Mon, 5 Feb 2007 20:18:37 +0000 (21:18 +0100)]
[S390] Convert memory detection into C code.
Hopefully this will make it more maintainable and less error prone.
Code makes use of search_exception_tables(). Since it calls this
function before the kernel exeception table is sorted, there is an
early call to sort_main_extable().
This way it's easy to use the already present infrastructure of fixup
sections. Also this would allows to easily convert the rest of
head[31|64].S into C code.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Preset the bogomips number to the cpu capacity value reported by
store system information in SYSIB 1.2.2. This value is constant
for a particular machine model and can be used to determine
relative performance differences between machines.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Michael Holzheu [Mon, 5 Feb 2007 20:18:29 +0000 (21:18 +0100)]
[S390] Hypervisor filesystem (s390_hypfs) for z/VM
This is an extension of the already existing hypfs for LPAR (DIAG 204).
Data returned by DIAG 2fc is exported using the s390_hypfs when Linux
is running under z/VM. Information about cpus and memory is provided.
Data is put into different virtual files which can be accessed from user
space. All values are represented as ASCII strings
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Michael Holzheu [Mon, 5 Feb 2007 20:18:26 +0000 (21:18 +0100)]
[S390] Add crypto support for 3592 tape devices
3592 tape devices are able to write data encrpyted on tape mediums.
This z/Linux device driver support includes the following functions:
* ioctl to switch on/off encryption
* ioctl to query encryption status of drive
* ioctls to set and query key encrypting keys (kekls)
* long busy interrupt handling
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Jan Glauber [Mon, 5 Feb 2007 20:18:22 +0000 (21:18 +0100)]
[S390] Support for s390 Pseudo Random Number Generator
Starting with the z9 the CPU Cryptographic Assist Facility comes with
an integrated Pseudo Random Number Generator. The generator creates
random numbers by an algorithm similar to the ANSI X9.17 standard.
The pseudo-random numbers can be accessed via a character device driver
node called /dev/prandom. Similar to /dev/urandom any amount of bytes
can be read from the device without blocking.
Signed-off-by: Jan Glauber <jan.glauber@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch adds support for clock synchronization to an external time
reference (ETR). The external time reference sends an oscillator
signal and a synchronization signal every 2^20 microseconds to keep
the TOD clocks of all connected servers in sync. For availability
two ETR units can be connected to a machine. If the clock deviates
for more than the sync-check tolerance all cpus get a machine check
that indicates that the clock is out of sync. For the lovely details
how to get the clock back in sync see the code below.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Gerald Schaefer [Mon, 5 Feb 2007 20:18:17 +0000 (21:18 +0100)]
[S390] noexec protection
This provides a noexec protection on s390 hardware. Our hardware does
not have any bits left in the pte for a hw noexec bit, so this is a
different approach using shadow page tables and a special addressing
mode that allows separate address spaces for code and data.
As a special feature of our "secondary-space" addressing mode, separate
page tables can be specified for the translation of data addresses
(storage operands) and instruction addresses. The shadow page table is
used for the instruction addresses and the standard page table for the
data addresses.
The shadow page table is linked to the standard page table by a pointer
in page->lru.next of the struct page corresponding to the page that
contains the standard page table (since page->private is not really
private with the pte_lock and the page table pages are not in the LRU
list).
Depending on the software bits of a pte, it is either inserted into
both page tables or just into the standard (data) page table. Pages of
a vma that does not have the VM_EXEC bit set get mapped only in the
data address space. Any try to execute code on such a page will cause a
page translation exception. The standard reaction to this is a SIGSEGV
with two exceptions: the two system call opcodes 0x0a77 (sys_sigreturn)
and 0x0aad (sys_rt_sigreturn) are allowed. They are stored by the
kernel to the signal stack frame. Unfortunately, the signal return
mechanism cannot be modified to use an SA_RESTORER because the
exception unwinding code depends on the system call opcode stored
behind the signal stack frame.
This feature requires that user space is executed in secondary-space
mode and the kernel in home-space mode, which means that the addressing
modes need to be switched and that the noexec protection only works
for user space.
After switching the addressing modes, we cannot use the mvcp/mvcs
instructions anymore to copy between kernel and user space. A new
mvcos instruction has been added to the z9 EC/BC hardware which allows
to copy between arbitrary address spaces, but on older hardware the
page tables need to be walked manually.
Signed-off-by: Gerald Schaefer <geraldsc@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Jan Glauber [Mon, 5 Feb 2007 20:18:14 +0000 (21:18 +0100)]
[S390] move crypto options and some cleanup.
This patch moves the config options for the s390 crypto instructions
to the standard "Hardware crypto devices" menu. In addition some
cleanup has been done: use a flag for supported keylengths, add a
warning about machien limitation, return ENOTSUPP in case the
hardware has no support, remove superfluous printks and update
email addresses.
Signed-off-by: Jan Glauber <jan.glauber@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
projects / linux-2.6 / log