iwlwifi: fix bug to show hidden APs during scan

Indirect scanning ('iwlist scan') should report information about
hidden APs. When an AP is hidden it does not respond to active scanning,
we thus have to use passive scanning to locate these APs.

This fixes http://bughost.org/bugzilla/show_bug.cgi?id=1499

Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Bill Moss <bmoss@clemson.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: change rate number to a constant

This patch moves a number to an understandable define

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: Fix endianity in debug print

This patch fix debug print out endianity issue for bitmap
Since u64 and le64 variables are casted to unsigned long long,
after patch 'wireless: correct warnings from using '%llx' for type 'u64'
also bitmaps need to be converted to native endianity

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: Use eeprom form iwlcore

This patch puts in use eeprom from iwlcore module

Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: update copyright year

Also fix a copy and paste error in header of iwl-core.c. This file
is not dual licensed.

Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: Use sta_bcast_id variable instead of BROADCAST_ID constant

This patch removes iwlYYY_BROADCAST_ID from run time usage.
hw_setting.sta_bcast_id is used instead.

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ssb: Add SPROM/invariants support for PCMCIA devices

This adds support for reading/writing the SPROM invariants
for PCMCIA based devices.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

include/net/ieee80211.h - remove duplicate include

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Only strip preamble bit in rt2400pci

Only rt2400pci can have the preamble bit set in the PLCP value,
for all other drivers it should not be cleared since that will
conflict with the plcp values for OFDM rates.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Release rt2x00 2.1.4

Version bump to 2.1.4

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Fix rt2400pci signal

After sampling hundreds of RX frame descriptors,
the results were conclusive:
- The Ralink documentation regarding the SIGNAL and RSSI are wrong.

It turns out that of the 5 BBR registers, we should not use BBR0 and BBR1
for SIGNAL and RSSI respectively, but actually BBR1 and BBR2.
BBR0 does show values, but the exact meaning remains unclear,
but they cannot be translated into a SIGNAL or RSSI field.
BBR3, BBR4 and BBR5 are always 0, so their meaning is unknown.

As it turns out, the reported SIGNAL is the PLCP value, this
in contradiction to what was expected looking at rt2500pci which
only reported the PLCP values for OFDM rates and bitrate values
for CCK rates.

This means we should let the driver raise the flag about the contents
of the SIGNAL field so rt2x00lib can always do the right thing based
on what the driver reports.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Fix RX DMA ring initialization

Due to a terrible typo the RX DMA base address
was initialized to the beacon base address.
Obviously bad things happen with bugs like that....

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Fix basic rate initialization

The basic rate which is configured in the register
should not match all supported rates, but only the _basic_ rates.

Fix this by adding a new flag to the rt2x00_rate structure
and whenever the mode is changed, loop over all available rates
for that band to get the basic rate mask.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Always enable TSF ticking

Whatever mode we are in, according to the legacy drivers
we should always enable TSF ticking/counting.
We should also always enable the TBCN/TBTT field,
this field is only disabled during beacon regeneration.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Make rt2x00leds_register return void

rt2x00dev isn't interested in the rt2x00leds_register() value
anyway. So lets make it return void to even prevent people from
assuming there is anybody interested in the returnvalue.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Rename config_preamble() to config_erp()

Rename config_preamble() to config_erp() and cleanup argument
list by putting it all into a single structure.
This will make the function more meaningful and easier to
expand later. This second option is mostly intended to make
the patch "mac80211: proper short-slot handling" from Johannes Berg
easier to apply for rt2x00.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Check IEEE80211_TXCTL_SEND_AFTER_DTIM flag

When mac sets the IEEE80211_TXCTL_SEND_AFTER_DTIM flag, we should
check if the ATIM queue is available in the driver and put the
frame in that queue for proper behavior (send frame after beacon interval).
Unfortunately not all drivers have this ATIM queue, and will lack
this feature for now.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Start bugging when rt2x00lib doesn't filter SW diversity

rt2x00lib should filter SW diversity out before sending any configuration
changes to the driver. When rt2x00lib fails to do this, it is important
that such events are reported because it _must_ be fixed.
So upgrading the error level to a BUG_ON() which will make sure
this bug gets noticed whenever it happens.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Move firmware checksumming to driver

rt2x00lib depended on 2 crc algorithms because rt61/rt73
use a different algorithm then rt2800. This means that
even when only 1 algorithm was needed, the dependency was
still present for both.
By moving the checksum generation to the driver we can clean
up 2 annoying flags (which indicated which checksum was required)
and move the dependency to where it belongs: the driver.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Upgrade queue->lock to use irqsave

The queue->lock could be grabbed from interrupt context,
which could lead to lockdep panic like this:

kernel: ======================================================
kernel: [ INFO: soft-safe -> soft-unsafe lock order detected ]
kernel: 2.6.25-0.95.rc4.fc9 #1
kernel: ------------------------------------------------------
kernel: rt2500pci/1251 [HC0[0]:SC0[1]:HE1:SE0] is trying to acquire:
kernel:  (&queue->lock){--..}, at: [<ffffffff88213339>] rt2x00queue_get_entry+0x5a/0x81 [rt2x00lib]
kernel:
kernel: and this task is already holding:
kernel:  (_xmit_IEEE80211){-...}, at: [<ffffffff8122e9a3>] __qdisc_run+0x84/0x1a9
kernel: which would create a new lock dependency:
kernel:  (_xmit_IEEE80211){-...} -> (&queue->lock){--..}
kernel:
kernel: but this new dependency connects a soft-irq-safe lock:
kernel:  (_xmit_ETHER){-+..}
kernel: ... which became soft-irq-safe at:
kernel:   [<ffffffffffffffff>] 0xffffffffffffffff
kernel:
kernel: to a soft-irq-unsafe lock:
kernel:  (&queue->lock){--..}
kernel: ... which became soft-irq-unsafe at:
kernel: ...  [<ffffffff810545a2>] __lock_acquire+0x62d/0xd63
kernel:   [<ffffffff81054d36>] lock_acquire+0x5e/0x78
kernel:   [<ffffffff812a1497>] _spin_lock+0x26/0x53
kernel:   [<ffffffff88212f98>] rt2x00queue_reset+0x16/0x40 [rt2x00lib]
kernel:   [<ffffffff88212fd4>] rt2x00queue_alloc_entries+0x12/0xab [rt2x00lib]
kernel:   [<ffffffff88213091>] rt2x00queue_initialize+0x24/0xf2 [rt2x00lib]
kernel:   [<ffffffff88212036>] rt2x00lib_start+0x3b/0xd4 [rt2x00lib]
kernel:   [<ffffffff88212609>] rt2x00mac_start+0x18/0x1a [rt2x00lib]
kernel:   [<ffffffff881b9a4b>] ieee80211_open+0x1f3/0x46d [mac80211]
kernel:   [<ffffffff8121d980>] dev_open+0x4d/0x8b
kernel:   [<ffffffff8121d41e>] dev_change_flags+0xaf/0x172
kernel:   [<ffffffff81224fc2>] do_setlink+0x276/0x338
kernel:   [<ffffffff81225198>] rtnl_setlink+0x114/0x116
kernel:   [<ffffffff812262fc>] rtnetlink_rcv_msg+0x1d8/0x1f9
kernel:   [<ffffffff8123649a>] netlink_rcv_skb+0x3e/0xac
kernel:   [<ffffffff8122611a>] rtnetlink_rcv+0x29/0x33
kernel:   [<ffffffff81235eed>] netlink_unicast+0x1fe/0x26b
kernel:   [<ffffffff81236224>] netlink_sendmsg+0x2ca/0x2dd
kernel:   [<ffffffff812103b3>] sock_sendmsg+0xfd/0x120
kernel:   [<ffffffff812105a8>] sys_sendmsg+0x1d2/0x23c
kernel:   [<ffffffff8100c1c7>] tracesys+0xdc/0xe1
kernel:   [<ffffffffffffffff>] 0xffffffffffffffff

This can be fixed by using the irqsave/irqrestore versions
during the queue->lock handling.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Fix trivial log message

Fix trivial log message.

Signed-off-by: Luis Correia <luis.f.correia@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00:correct rx packet length for USB devices

When fixing up the packet alignment, if we had to add 2 bytes to the front of
the skb we need to remember to take them off the end afterwards. This fixes
reception of encrypted packets which were otherwise failing with an invalid
ICV.

Signed-off-by: Adam Baker <linux@baker-net.org.uk>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Only disable beaconing just before beacon update

We should not write 0 to the beacon sync register during
config_intf() since that will clear out the beacon interval
and forces the beacon to be send out at the lowest interval.
(reported by Mattias Nissler).

The side effect of the same bug was that while working with
multiple virtual AP interfaces a change for any of those
interfaces would disable beaconing untill an beacon update
was provided.

This is resolved by only updating the TSF_SYNC value during
config_intf(). In update_beacon() we disable beaconing
temporarily to prevent fake beacons to be transmitted.
Finally kick_tx_queue() will enable beaconing again.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Use skbdesc fields for descriptor initialization

In rt2x00lib_write_tx_desc() the skb->data and skb->len fields
were incorrectly used. For USB drivers both of those values
contain invalid data (skb->data points to the device descriptor,
skb->len contains the frame _and_ descriptor length).

Instead of using the skbuffer fields we should use the skbdesc
fields which are correctly initialized and contain all the data
that we need.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Don't use unitialized rxdesc->size

rxdesc->size is unitialized before the desriptor has been read.
Move the truncation of the sk buffer to the moment all variables
have been initialized.

Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Don't use uninitialized desc_len

skbdesc->desc_len is uninitialized at the start
of the function. So it is a _bad_ idea to use it...

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Use the correct size when copying the control info in txdone

The sizeof() operator was incorrectly applied to the pointer, not the struct.

Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Initialize TX control field in data entries

In the TX path, the driver didn't copy the TX control data structure. Thus, it
was invalid in the TX done handler, causing serious trouble and misbehaviour.

Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Align RX descriptor to 4 bytes

Some architectures give problems when reading
RX frame descriptor words when the descriptor
is not aligned on a 4 byte boundrary.

Due to optimalizations for the ieee80211 payload
4 byte alignment, it is no longer guarenteed
that the descriptor is placed on the 4 byte
boundrary (In fact, for rt73usb it is absolutely
never aligned to 4 bytes, for rt2500usb it depends
on the length of the payload).

This will copy the descriptor to a 4 byte aligned
location before it is read for the first time.
This will also move the payload data alignment
in rt2x00usb (instead of inside the driver) where
it has always belonged.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: pull out helpers for writing noise table

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rndis_wlan: cleanup, rename structure members

Rename members of ndis_80211_* structures to match the style of
the rest of the code.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rndis_wlan: cleanup, rename and reorder enums and structures

Rename enums and structures to ndis_80211_* for greater readability.
Also change order so that enumerations are presented first.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

drivers/net/wireless/ath5k - convert == (true|false) to simple logical tests

(test == true) is not nice.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: implement SSID scanning for SIOCSIWSCAN

After my bit scan re-writing the SIOCSIWSCAN wext ioctl no longer supported
scanning for a specific SSID. However, wpa_supplicant is a possible user of
this ioctl, so here is code that add's this.

While passing, removed even more of the debugfs-based scanning. You can (and
should) the SIOCSIWSCAN to ask for scans, so there is no need for
proprietary interfaces for scanning. And, besides, the scan result couldn't
be used further, e.g. not for associating.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

the scheduled rc80211-simple.c removal

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

the scheduled ieee80211 softmac removal

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

the scheduled bcm43xx removal

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: <Larry.Finger@lwfinger.net>
Cc: <stefano.brivio@polimi.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

make b43_mac_{enable,suspend}() static

b43_mac_{enable,suspend}() can now become static.

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/linville/wireless-2.6.26

iwlwifi: fix potential lock inversion deadlock

This is a change to a previous patch ("iwlwifi: 3945 split tx_complete
to command and packet function") to ensure we do not have hardirq safe
locks (priv->lock in this case) depend on hardirq unsafe locks.

We only call iwl3945_tx_queue_reclaim while in a tasklet so we have to use
the irqsafe version of the function.

Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wireless: correct warnings from using '%llx' for type 'u64'

drivers/net/wireless/ath5k/debug.c: In function 'read_file_tsf': drivers/net/wireless/ath5k/debug.c:203: warning: format '%016llx'
expects type 'long long unsigned int', but argument 4 has type 'u64' drivers/net/wireless/ath5k/debug.c:203: warning: format '%016llx'
expects type 'long long unsigned int', but argument 4 has type 'u64' drivers/net/wireless/ath5k/debug.c: In function 'read_file_beacon':
drivers/net/wireless/ath5k/debug.c:274: warning: format '%016llx' expects type 'long long unsigned int', but argument 4 has type 'u64'
drivers/net/wireless/ath5k/debug.c:274: warning: format '%016llx' expects type 'long long unsigned int', but argument 4 has type 'u64'

drivers/net/wireless/iwlwifi/iwl-4965.c: In function 'iwl4965_tx_status_reply_compressed_ba':
drivers/net/wireless/iwlwifi/iwl-4965.c:3907: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'u64'
drivers/net/wireless/iwlwifi/iwl-4965.c: In function 'iwl4965_rx_reply_compressed_ba':
drivers/net/wireless/iwlwifi/iwl-4965.c:4039: warning: format '%llx' expects type 'long long unsigned int', but argument 6 has type '__le64'
drivers/net/wireless/iwlwifi/iwl-4965.c:4046: warning: format '%llx' expects type 'long long unsigned int', but argument 5 has type 'u64'
drivers/net/wireless/iwlwifi/iwl4965-base.c: In function 'iwl4965_tx_status_reply_tx':
drivers/net/wireless/iwlwifi/iwl4965-base.c:3661: warning: format '%llx' expects type 'long long unsigned int', but argument 6 has type 'u64'

Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: work around wrong beacon rx timestamp in IBSS mode

atheros hardware has a problem with the rx timestamp of some IBSS beacons when
they caused a TSF update (they have the same BSSID).

the rx timestamp is wrong especially if the beacon frames get bigger than 78
byte (at least on AR5213 and AR5414 hardware). in that case ath5k_extend_tsf()
will assume a rs_tstamp overflow and give us a timestamp too far in the past
which will cause mac80211 to merge IBSS on every beacon (which is not necessary
since the BSSID already matches). but in this case we know that the HW must
have synced to the beacons TSF and the rx timestamp must be later than that so
we can adjust mactime accordingly.

also rename the function to ath5k_check_ibss_tsf() and change comments, since
"hw merge" is better described as a TSF update.

drivers/net/wireless/ath5k/base.c:      Changes-licensed-under: 3-Clause-BSD

Signed-off-by: Bruno Randolf <bruno@thinktube.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: add notes about rx timestamp

add comments about the fact that we don't know when exactly the atheros
hardware takes the RX timestamp.

drivers/net/wireless/ath5k/base.c:      Changes-licensed-under: 3-Clause-BSD

Signed-off-by: Bruno Randolf <bruno@thinktube.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: move rx and tx status structures out of hardware descriptor

move ath5k_tx_status and ath5k_rx_status structures out of the hardware
descriptor since they are not accessed by the hardware at all. they just
contain converted information from the hardware descriptor. since they are only
used in the rx and tx tasklets there is also no use to keep them for each
descriptor.

drivers/net/wireless/ath5k/ath5k.h:     Changes-licensed-under: ISC
drivers/net/wireless/ath5k/base.c:      Changes-licensed-under: 3-Clause-BSD
drivers/net/wireless/ath5k/debug.c:     Changes-licensed-under: GPL
drivers/net/wireless/ath5k/debug.h:     Changes-licensed-under: GPL
drivers/net/wireless/ath5k/hw.c:        Changes-licensed-under: ISC

Signed-off-by: Bruno Randolf <bruno@thinktube.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: struct ath5k_desc cleanups

* make struct ath5k_desc clearer by directly including unions of structures,
  which correspond to the hardware descriptors of different HW versions (5210
  and 5212). before they were casted at onto ath5k_desc at different points
  (e.g.  ds_hw[2]).

* rename some structures and variable names to make their use clearer, e.g.
  struct ath5k_hw_4w_tx_desc to ath5k_hw_4w_tx_ctl.

* substitute "old" with "5210" and "new" with "5212" (eg. rename
  ath5k_hw_proc_new_rx_status() to ath5k_hw_proc_5212_rx_status()) because old
  and new are relative and we might have a newer structure at some point.

* unify structs ath5k_hw_old_rx_status and ath5k_hw_new_rx_status into one
  ath5k_hw_rx_status, because they only differ in the flags and masks.

drivers/net/wireless/ath5k/ath5k.h:     Changes-licensed-under: ISC
drivers/net/wireless/ath5k/debug.c:     Changes-licensed-under: GPL
drivers/net/wireless/ath5k/hw.c:        Changes-licensed-under: ISC
drivers/net/wireless/ath5k/hw.h:        Changes-licensed-under: ISC

Signed-off-by: Bruno Randolf <bruno@thinktube.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: grab NIC access when disabling aggregations

This patch grabs NIC access inside iwl4965_tx_queue_agg_disable, instead of the
caller doing it.
The caller must still hold priv->lock when calling the function.

Signed-off-by: Max Stepanov <max.stepanov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: 3945 split tx_complete to command and packet function

This patch
1. removes cmd completion from iwl3945_tx_queue_reclaim
and creates iwl3945_cmd_queue_reclaim.
1. removes 11n relevant elements from this function
2. removes call to ieee80211_tx_status_irqsafe
and uses ieee80211_tx_status only

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: Fix 3945 rate scaling

This patch fix 3945 rate scaling after cfg80211 rate/band changes

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: queue functions cleanup

This patch moves
1. iwl_queue_inc_wrap and int iwl_queue_dec_wrap
into  iwl-helpers.h these two functions are identical to common
for both iwl3956 and iwl4965
2. renames x2_queue_used to iwl3945_x2_queue_used
3. exports iwl3945_queue_space out of iwl3964-base.c

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: Moving EEPROM handling in iwlcore module

This patch move EEPROM code into iwl core module

Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: add iwl-core module

This patch adds iwl-core module to iwlwifi driver.
This module will contain common code and infrastracture for iwlwifi
driver

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: fix locking unbalance in 4965 rate scale

This patch fixes locking unbalance after adding rcu locking
for sta

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: document IEEE80211_TXCTL_OFDM_HT

This patch clarifies the use of IEEE80211_TXCTL_OFDM_HT flag.

Can by united with patch "mac80211: adding mac80211_tx_control
flags and HT flags"

Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: Cancel scanning upon association

This patch cancels an ongoing HW scan upon association. Not doing this
resulted in instability in association.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: Take the fw file name from the iwl_cfg.

This patch adds fw_name to iwl_cfg. This allows run time selection
of needed fw/ucode file

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: add struct iwl_cfg

This patch introduces struct iwl_cfg. struct iwl_cfg defines static
configuration for each device type and sku. It is passed as driver_data
to the bus probe function.
This patch also introduce new common header file iwl-core.h
which will represent core functionality of iwlwifi driver

3945ABG uses separate iwl-3945-dev.h header file for now

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: Move HBUS address to iwl-csr.h

HBUS is accessed through CSR registers
moved to iwl-csr.h

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: extract iwl-csr.h

This patch extract CSR Register definition into separate
header files as most of the definition are commons to both
3945 and 4965.

Definitions specific for 3945 and 4965 are properly prefixed

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: use mac80211_tx_control_flags

This patch makes use of the new mac80211_tx_control_flags and tx_rate to
pass Tx data, regular and 11n, from the HW tx response into the rate scaling.

Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: adding mac80211_tx_control_flags and HT flags

This patch makes enum from the defines previously dwelled inside
ieee80211_tx_control for better readability.
The patch also addes HT flags, for 802.11n drivers:
- IEEE80211_TXCTL_OFDM_HT: request low-level driver to use HT OFDM rates
- IEEE80211_TXCTL_GREEN_FIELD: use green field protection
- IEEE80211_TXCTL_DUP_DATA: duplicate data on both 20 Mhz channels
- IEEE80211_TXCTL_40_MHZ_WIDTH: send this frame in 40Mhz width
- IEEE80211_TXCTL_SHORT_GI: send this frame with short guard interval

Tx command can be a combination of any of these flags, along with
bitrate represented by ieee80211_rate. this will allow legacy drivers to
switch easily to any 11n rate representation.

Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
CC: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: 802.11n spec removes AUTO offset for FAT channel

This patch adapts to 802.11 patch and remove AUTO offset for FAT
channel

Signed-off-by: Guy Cohen <guy.cohen@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: Fix failed frames status report typo

This fixes a typo in the status report.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: Add TX statistics debugging counters

This adds a few debugging counters, that are useful for debugging the
"card does not transmit" or "connection is unstable" kind of problems.
It's also useful for tuning an RC algorithm.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: Rename the DMA ring pointers

Rename the DMA ring pointers to have more descriptive and standard
names. Also remove the 6th unused TX ring. We can add it back later,
if we need it. The unused TX-status rx-ring is also removed, as that's
only used by legacy devices not supported by this driver anyway.

This is no functional change, except less memory allocation for
the removed rings.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: Add QOS support

This adds QOS support to the b43 driver.
QOS can be disabled on driver level with a module parameter for debugging purposes.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: don't call conf_tx under RCU lock

Reinette pointed out that with the sta_info RCU-ification
the behaviour here changed and the conf_tx callback is
now invoked under RCU read lock. That is not necessary so
this patch restores the original behaviour

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Tested-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: Add 2413 to srev_names so that it shows up during module load

Add 2413 to srev_names so that it shows up during module load.
This is based on the new patch 7 which did not introduce a helper
on ath5k_hw_reset().

Changes-licensed-under: 3-clause-BSD
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@winlab.rutgers.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: Make some changes to follow register dumps.

Make some changes which mimic what we see in register dumps.
This patch does not add a helper to ath5k_hw_reset(). It
does seem clear we need a re-shuffle around ath5k_hw_reset()
though as code in there is lengthy and already hitting 80-char
limit. This can be dealt with later though.

Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@winlab.rutgers.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: Fixes for PCI-E cards

 * Fix nic_wakeup for PCI-E chips (don't set AR5K_RESET_CTL_PCI bit)

 * Fix dma size setting for PCI-E chips (thanx to Bob Copeland).

Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@winlab.rutgers.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: Remove RF5413 from rf gain optimization functions

 * Since RF2413 it seems that RF_BUFFER settings are different (notice
that the last part -"bank 7" or whatever- is smaller than in 5111/5112).
So until we know what's going on we assume there is no gain optimization
stuff in post-5112 chips.

Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@winlab.rutgers.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: more RF2413 stuff

 * Add AR5K_RF2413 to radio check during hw_reset so it doesn't complain

 * Write ah_phy_spending value we set during attach instead of checking
each time for radio revision

 * Skip txpower setup for RF2413 because it can't transmit with it
(weird thing is that RF5413 has no problem with it).

Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@winlab.rutgers.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: Identify RF2413 and deal with PHY_SPENDING

 * Attach RF2413.

 * Propertly handle different AR5K_PHY_SPENDING settings for each RF
chip by adding a field in ath5k_hw. This way we won't have to check
inside hw_reset (see next patch).

Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@winlab.rutgers.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: Add RF2413 initial settings

* Add initial settings for RF2413

Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@winlab.rutgers.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: Add RF2413 srev values

 * Add RF2413 srev values and a new entry on ath5k_radio enum for it
  since it differs from RF5413 (it's not like 5112-2112).

Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@winlab.rutgers.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[NETNS][IPV6] mcast - handle several network namespace

This patch make use of the network namespace information at the right
places to handle the multicast for several network namespaces.  It
makes the socket control to be per namespace too.

Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

[NETNS][IPV6] tcp6 - handle several network namespace

We have the right network namespace at the right place now.
So make use of this information to make tcp6 per network namespace

Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

[NETNS][IPV6] tcp6 - make socket control per namespace

Instead of having a tcp6_socket global to all the namespace, there is
tcp6 socket control per namespace. That is consistent with which
namespace sent a RST and allows to pass the socket to the underlying
function to retrieve the network namespace.

Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

[NETNS][IPV6] ndisc - make socket control per namespace

Make ndisc socket control per namespace.

Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

[NETNS][IPV6] ndisc - make ndisc handle multiple network namespaces

Make ndisc handle multiple network namespaces:
Remove references to init_net, add network namespace parameters and add
pernet_operations for ndisc

Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

[NETNS][IPV6] fix some missing namespace

This patch adds some missing namespace

Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[UDP]: Revert udplite and code split.

This reverts commit db1ed684f6c430c4cdad67d058688b8a1b5e607c ("[IPV6]
UDP: Rename IPv6 UDP files."), commit
8be8af8fa4405652e6c0797db5465a4be8afb998 ("[IPV4] UDP: Move
IPv4-specific bits to other file.") and commit
e898d4db2749c6052072e9bc4448e396cbdeb06a ("[UDP]: Allow users to
configure UDP-Lite.").

First, udplite is of such small cost, and it is a core protocol just
like TCP and normal UDP are.

We spent enormous amounts of effort to make udplite share as much code
with core UDP as possible.  All of that work is less valuable if we're
just going to slap a config option on udplite support.

It is also causing build failures, as reported on linux-next, showing
that the changeset was not tested very well.  In fact, this is the
second build failure resulting from the udplite change.

Finally, the config options provided was a bool, instead of a modular
option.  Meaning the udplite code does not even get build tested
by allmodconfig builds, and furthermore the user is not presented
with a reasonable modular build option which is particularly needed
by distribution vendors.

Signed-off-by: David S. Miller <davem@davemloft.net>

[TIPC]: Update version to 1.6.3

This patch updates TIPC's version number to 1.6.3.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[TIPC]: Enhancements to message header writing

This patch makes two enhancements to the routine used to
set bit fields within a TIPC message header:

 1) It now ignores any bits of the new field value that are not
    covered by the mask being used.  (Previously, if the new value
    exceeded the size of the mask the extra bits could corrupt
    other fields in the message header word being updated.)

 2) The code has been optimized to minimize the number of run-time
    endianness conversion operations by leveraging the fact that the
    mask (and, in some cases, the value as well) is constant and the
    necessary conversion can be performed by the compiler.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[TIPC]: Use correct bitmask when setting version

This patch ensures that the 3-bit version field of the TIPC
message header is masked correctly when written into a message.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[TIPC]: Minor cleanup of message header code

This patch eliminates some unused or duplicate message header
symbols, and fixes up the comments and/or location of a few
other symbols.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[TIPC]: Eliminate "sparse" symbol warnings

This patch eliminates warnings about undeclared symbols.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[TIPC]: Add argument validation for shutdown()

This patch validates that the "how" argument to shutdown()
is SHUT_RDWR, since this is the only form that TIPC supports.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[TIPC]: Removal of message header option code

This patch removes code associated with optional, user-specified
fields of the TIPC message header.  Such fields were never
utilized by TIPC, and have now been removed from the protocol
specification.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

zd1211rw: support for mesh interface and beaconing

The previously unused CR_CAM_MODE register is set to MODE_AP_WDS. This makes the
driver ack mesh (WDS) frames. It does not affect Infra functionality of the
driver.

Previously missing beaconing support has been added. This might also help
implement a currently missing ah-hoc mode.

Support for interrupts from the device have been added, but we are not handling
most of them.

Mesh interfaces are considered associated as long as the interface is up.

Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: clean up scan.c, remove zeromac and bcastmac

Should be purely cosmetic apart from the removal of the two pointless
MAC addresses.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: convert 802_11_SCAN to a direct command

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: add LED control TLV to types.h

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: convert KEY_MATERIAL to a direct command

The struct enc_key probably wants to die too, but that can come later.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: Fix 52 rate report in rx status

This patch fixes reporting rate in RX packets in 52 band.
The rate was updated from CCK rate index instead of OFDM rate 6M
Most of the patch is collateral clean up

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: refactor init geos function

This patch refactors init geos function. It also fixes few minor bugs.
IWL_MAX_RATE -> IWL_RATE_COUNT (IWL_MAX_RATE included also MCS setting)
There are 9 and 13 rates for 4965 in 2.4 and 5.2 respectively  (rate 60)

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: removing unused priv->config

This patch removes unused variable in iwlYYYY_priv

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ssb: Add Gigabit Ethernet driver

This adds the Gigabit Ethernet driver for the SSB
Gigabit Ethernet core. This driver actually is a frontend to
the Tigon3 driver. So the real work is done by tg3.
This device is used in the Linksys WRT350N.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: fix hardware scan completion

The mac80211 MLME requires restarting timers after a scan
completes but this wasn't done when hardware scan offload
was added, so add it now.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Tested-by: Bill Moss <bmoss@clemson.edu>
Cc: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: fix mesh_path and sta_info get_by_idx functions

Skip properly entries whose dev does not match.

Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: path IE fields macros, fix alignment problems and clean up

Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>