Grant Likely [Tue, 2 Oct 2007 02:16:09 +0000 (12:16 +1000)]
[POWERPC] Uartlite: Let the console be initialized earlier
By configuring it earlier we get console output sooner which is helpful
for debugging when the kernel crashes before the serial drivers are
initialized.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Grant Likely [Tue, 2 Oct 2007 02:15:59 +0000 (12:15 +1000)]
[POWERPC] Uartlite: Comment block tidy
Tidy the comments to split the driver into logical section; the main driver,
the console driver, the platform bus binding, and module initialization
and teardown.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Grant Likely [Tue, 2 Oct 2007 02:15:39 +0000 (12:15 +1000)]
[POWERPC] Uartlite: Fix reg io to access documented register size
The Uartlite data sheet defines the registers as 32 bit wide. This
patch changes the register access to use 32 bit transfers and eliminates
the magic +3 offset which is currently required to make the device
work.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: John Williams <jwilliams@itee.uq.edu.au> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Grant Likely [Tue, 2 Oct 2007 02:15:29 +0000 (12:15 +1000)]
[POWERPC] Virtex: Add generic Xilinx Virtex board support
Adds support for generic Xilinx Virtex boards. Any board which specifies
"xilinx,virtex" in the compatible property will make use of this board
support.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
[POWERPC] 4xx: 440EPx/GRx incorrect write to DDR SDRAM errata workaround
Add a workaround for PowerPC 440EPx/GRx incorrect write to
DDR SDRAM errata. Data can be written to wrong address
in SDRAM when write pipelining enabled on plb0. We disable
it in the cpu_setup for these processors at early init.
[POWERPC] 4xx: Move 440EP(x) FPU setup from head_44x to cpu_setup_4xx
The PowerPC 440EP(x) FPU init is currently done in head_44x
under ifdefs. Since we should support more then one board
in the same kernel, we move FPU initialization code from head_44x
to cpu_setup_44x and add cpu_setup callbacks for 440EP(x).
[POWERPC] 4xx: Introduce cpu_setup functionality to 44x platform
This adds cpu_setup functionality for ppc44x platform.
Low level cpu-spefic initialization routines should be
placed in cpu_setup_44x.S and a callback should be
added to cputable. The cpu_setup is invoked
by identify_cpu() function at early init.
Tony Breeds [Fri, 21 Sep 2007 03:26:03 +0000 (13:26 +1000)]
[POWERPC] Implement clockevents driver for powerpc
This registers a clock event structure for the decrementer and turns
on CONFIG_GENERIC_CLOCKEVENTS, which means that we now don't need
most of timer_interrupt(), since the work is done in generic code.
For secondary CPUs, their decrementer clockevent is registered when
the CPU comes up (the generic code automatically removes the
clockevent when the CPU goes down).
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Tony Breeds [Wed, 3 Oct 2007 01:19:09 +0000 (11:19 +1000)]
[POWERPC] Fix panic in RTAS code
Some older pSeries machines were panicking in pSeries_log_error
because it was getting called before it was ready. This is a result
of commit "[POWERPC] pseries: Fix jumbled no_logging flag."
(79c0108d1b9db4864ab77b2a95dfa04f2dcf264c).
This fixes it by explicitly enabling RTAS error logging when it has
been initialized, and also makes the code clearer by renaming the
"no_more_logging" variable to "logging_enabled".
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Ishizaki Kou [Tue, 2 Oct 2007 08:26:53 +0000 (18:26 +1000)]
[POWERPC] Celleb: update for PCI
This adds support for the PCI bus on Celleb with new "I/O routines
for PowerPC." External PCI on Celleb must do explicit synchronization
with devices (Bus has no automatic synchronization feature).
Ishizaki Kou [Tue, 2 Oct 2007 08:21:21 +0000 (18:21 +1000)]
[POWERPC] Celleb: Support for Power/Reset buttons
This supports Power/Reset buttons on Beat on Celleb.
On Beat, we have an event from Beat if Power button or Reset button
is pressed. This patch catches the event and convert it to a signal
to INIT process by calling ctrl_alt_del() function.
/sbin/inittab have no entry to turn the machine power off so we have
to detect if power button is pressed or not internally in our driver.
This idea is taken from PS3's event handling subsystem.
Michael Ellerman [Mon, 17 Sep 2007 06:05:02 +0000 (16:05 +1000)]
[POWERPC] Update axon_msi to use dcr_host_t.base
Now that dcr_host_t contains the base address, we can use that in the
axon_msi code, rather than storing it separately.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Michael Ellerman [Mon, 17 Sep 2007 06:05:01 +0000 (16:05 +1000)]
[POWERPC] Update mpic to use dcr_host_t.base
Now that dcr_host_t contains the base address, we can use that in the mpic
code, rather than storing it separately.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Michael Ellerman [Mon, 17 Sep 2007 06:05:00 +0000 (16:05 +1000)]
[POWERPC] Store the base address in dcr_host_t
In its current form, dcr_map() doesn't remember the base address you passed
it, which means you need to store it somewhere else. Rather than adding the
base to another struct it seems simpler to store it in the dcr_host_t.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Adrian Bunk [Tue, 2 Oct 2007 20:30:09 +0000 (13:30 -0700)]
[POWERPC] Select proper defconfig for crosscompiles
The trick for finding the right defconfig is neat, but you forgot to
provide an i686_defconfig. ;-)
More seriously, cross compiling the defconfig is often useful, e.g. for
testing the compilation of patches that touch multiple architectures,
and this patch therefore chooses g5_defconfig if $(CROSS_COMPILE) is
non-empty.
Signed-off-by: Adrian Bunk <bunk@kernel.org> Acked-by: Sam Ravnborg <sam@ravnborg.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Olof Johansson <olof@lixom.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Cyrill Gorcunov [Tue, 2 Oct 2007 20:30:08 +0000 (13:30 -0700)]
[POWERPC] Sky Cpu: use C99 style for struct init
This changes structure item init format to C99, and removes useless
structure items init.
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Kumar Gala <galak@gate.crashing.org> Cc: Brian Waite <waite@skycomputers.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Cyrill Gorcunov [Tue, 2 Oct 2007 20:30:07 +0000 (13:30 -0700)]
[POWERPC] Sky Cpu and Nexus: check for create_proc_entry ret code
Adds checking of create_proc_entry call to prevent possible NULL
pointer usage.
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Kumar Gala <galak@gate.crashing.org> Cc: Brian Waite <waite@skycomputers.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Cyrill Gorcunov [Tue, 2 Oct 2007 20:30:06 +0000 (13:30 -0700)]
[POWERPC] Sky Cpu and Nexus: check for platform_get_resource retcode
Add adds checking for platform_get_resource() return code to prevent
possible NULL pointer usage.
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Kumar Gala <galak@gate.crashing.org> Cc: Brian Waite <waite@skycomputers.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Cyrill Gorcunov [Tue, 2 Oct 2007 20:30:06 +0000 (13:30 -0700)]
[POWERPC] Sky Cpu and Nexus: include io.h
Add #include <asm/io.h> directive to properly declare ioremap() and
writel().
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Kumar Gala <galak@gate.crashing.org> Cc: Brian Waite <waite@skycomputers.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Cyrill Gorcunov [Tue, 2 Oct 2007 20:30:05 +0000 (13:30 -0700)]
[POWERPC] Sky Cpu and Nexus: code style improvement
Remove useless spaces and adds some empty lines to make code more
readable. Also marker for printk is added.
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Kumar Gala <galak@gate.crashing.org> Cc: Brian Waite <waite@skycomputers.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Roland McGrath [Tue, 2 Oct 2007 20:30:04 +0000 (13:30 -0700)]
[POWERPC] powerpc vDSO: install unstripped copies on disk
This keeps an unstripped copy of the vDSO images built before they are
stripped and embedded in the kernel. The unstripped copies get installed in
$(MODLIB)/vdso/ by "make install". These files can be useful when they
contain source-level debugging information.
Signed-off-by: Roland McGrath <roland@redhat.com> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Fixes this powerpc build error in 2.6.22-rc6-mm1 for powerpc 64 with
CONFIG_SWAP=n :
In file included from include2/asm/tlb.h:60,
from /home/compudj/git/linux-2.6-lttng/arch/powerpc/mm/init_64.
c:56:
/home/compudj/git/linux-2.6-lttng/include/asm-generic/tlb.h: In function 'tlb_flush_mmu':
/home/compudj/git/linux-2.6-lttng/include/asm-generic/tlb.h:76: error: implicit declaration of function 'release_pages'
/home/compudj/git/linux-2.6-lttng/include/asm-generic/tlb.h: In function 'tlb_remove_page':
/home/compudj/git/linux-2.6-lttng/include/asm-generic/tlb.h:105: error: implicit declaration of function 'page_cache_release'
make[2]: *** [arch/powerpc/mm/init_64.o] Error 1
release_pages is declared in linux/pagemap.h, but cannot be included in
linux/swap.h because of a sparc related comment:
/* only sparc can not include linux/pagemap.h in this file
* so leave page_cache_release and release_pages undeclared... */
#define free_page_and_swap_cache(page) \
page_cache_release(page)
#define free_pages_and_swap_cache(pages, nr) \
release_pages((pages), (nr), 0);
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Hugh Dickins [Tue, 31 Oct 2006 18:44:54 +0000 (05:44 +1100)]
[POWERPC] ppc64: support CONFIG_DEBUG_PREEMPT
Add CONFIG_DEBUG_PREEMPT support to ppc64: it was useful for testing
get_paca() preemption. Cheat a little, just use debug_smp_processor_id()
in the debug version of get_paca(): it contains all the right checks and
reporting, though get_paca() doesn't really use smp_processor_id().
Use local_paca for what might have been called __raw_get_paca().
Silence harmless warnings from io.h and lparcfg.c with local_paca -
it is okay for iseries_lparcfg_data to be referencing shared_proc
with preemption enabled: all cpus should show the same value for
shared_proc.
Why do other architectures need TRACE_IRQFLAGS_SUPPORT for DEBUG_PREEMPT?
I don't know, ppc64 appears to get along fine without it.
Signed-off-by: Hugh Dickins <hugh@veritas.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Scott Wood [Thu, 27 Sep 2007 18:38:55 +0000 (04:38 +1000)]
[POWERPC] Make instruction dumping work in real mode
On non-book-E, exceptions execute in real mode. If a fault happens
that leads to a register dump, the kernel currently prints XXXXXXXX
because it doesn't realize that PC is a physical address.
This patch checks whether instruction address translation is turned
on, and if not converts PC into a virtual address.
Signed-off-by: Scott Wood <scottwood@freescale.com> Acked-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Olof Johansson <olof@lixom.net> Signed-off-by: Paul Mackerras <paulus@samba.org>
The /proc/bus/pci/* files list PCI domain numbers only for
devices that claim to be on a multi-domain system. The check
for this is broken on powerpc, because the buid value is
truncated to 32 bits.
There is at least one machine (IBM QS21) that only uses
the high-order bits of the buid, so the return value
of pci_proc_domain() ends up being always zero, which
makes /proc/bus/pci useless.
Change the logic to always return '1' for a nonzero
buid value.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Roland McGrath [Mon, 24 Sep 2007 23:50:52 +0000 (09:50 +1000)]
[POWERPC] Add CHECK_FULL_REGS in several places in ptrace code
This restores the CHECK_FULL_REGS sanity check to every place that can
access the nonvolatile GPRs for ptrace. This is already done for
native-bitwidth PTRACE_PEEKUSR, but was omitted for many other cases
(32-bit ptrace, PTRACE_GETREGS, etc.); I think there may have been more
uniform checks before that were lost in the recent cleanup of GETREGS et al.
Signed-off-by: Roland McGrath <roland@redhat.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Scott Wood [Mon, 24 Sep 2007 20:09:49 +0000 (06:09 +1000)]
[POWERPC] bootwrapper: Add PlanetCore firmware support
This is a library that board code can use to extract information from the
PlanetCore configuration keys. PlanetCore is used on various boards from
Embedded Planet.
Signed-off-by: Scott Wood <scottwood@freescale.com> Acked-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
Scott Wood [Mon, 24 Sep 2007 20:09:11 +0000 (06:09 +1000)]
[POWERPC] bootwrapper: Factor out dt_set_mac_address()
This allows callers to set addresses one at a time when that would be more
convenient.
Signed-off-by: Scott Wood <scottwood@freescale.com> Acked-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
Ed Swarthout [Fri, 21 Sep 2007 02:53:02 +0000 (12:53 +1000)]
[POWERPC] Add memory regions to the kcore list for 32-bit machines
The entries are only 32-bit, so restrict the virtual address to stay
below 0xffff_ffff. With KERNELBASE set to 0xc000_0000, this in effect
restricts access to the first 1GB of real memory.
Make setup_kcore conditional on CONFIG_PROC_KCORE for both 32/64.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Paul Mackerras [Fri, 21 Sep 2007 01:52:36 +0000 (11:52 +1000)]
[POWERPC] Disable power management for arch/ppc
Currently the prep_defconfig in arch/ppc won't build due to swsusp
being broken. This patch avoids the problem by essentially disabling
all power management on those platforms left in arch/ppc.
Stephen Rothwell [Fri, 21 Sep 2007 00:16:20 +0000 (10:16 +1000)]
[POWERPC] Create and use CONFIG_WORD_SIZE
Linus made this suggestion for the x86 merge and this starts the process
for powerpc. We assume that CONFIG_PPC64 implies CONFIG_PPC_MERGE and
CONFIG_PPC_STD_MMU_32 implies CONFIG_PPC_STD_MMU.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
Domen Puncer [Thu, 20 Sep 2007 14:00:11 +0000 (00:00 +1000)]
[POWERPC] clk.h interface for platforms
This provides an implementation of the <linux/clk.h> interface for
arch/powerpc using a set of function pointers in clk_functions.
Platforms that want to support this interface should fill
clk_functions and select CONFIG_PPC_CLOCK in Kconfig.
Signed-off-by: Domen Puncer <domen.puncer@telargo.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Michael Ellerman [Thu, 20 Sep 2007 06:36:51 +0000 (16:36 +1000)]
[POWERPC] Inline u3msi_compose_msi_msg()
In the MPIC U3 MSI code, we call u3msi_compose_msi_msg() once for each MSI.
This is overkill, as the address is per pci device, not per MSI. So setup
the address once, and just set the data per MSI.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently rtas_change_msi() returns either the error code from RTAS, or if
the RTAS call succeeded the number of irqs that were configured by RTAS.
This makes checking the return value more complicated than it needs to be.
Instead, have rtas_change_msi() check that the number of irqs configured by
RTAS is equal to what we requested - and return an error otherwise. This makes
the return semantics match the usual 0 for success, something else for error.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
Michael Ellerman [Thu, 20 Sep 2007 06:36:48 +0000 (16:36 +1000)]
[POWERPC] Simplify error logic in rtas_setup_msi_irqs()
rtas_setup_msi_irqs() doesn't need to call teardown() itself, the
generic code will do this for us as long as we return a non-zero
value.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Michael Ellerman [Thu, 20 Sep 2007 06:36:47 +0000 (16:36 +1000)]
[POWERPC] Simplify error logic in u3msi_setup_msi_irqs()
u3msi_setup_msi_irqs() doesn't need to call teardown() itself,
the generic code will do this for us as long as we return a non
zero value.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Michael Ellerman [Mon, 17 Sep 2007 06:03:45 +0000 (16:03 +1000)]
[POWERPC] Make sure to of_node_get() the result of pci_device_to_OF_node()
pci_device_to_OF_node() returns the device node attached to a PCI device,
but doesn't actually grab a reference - we need to do it ourselves.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Arnd Bergmann [Wed, 29 Aug 2007 23:11:24 +0000 (09:11 +1000)]
[POWERPC] Move embedded6xx into multiplatform
The various embedded 6xx systems can easily coexist in one kernel
together with the other 6xx based systems, so there is no strict
reason to keep them separate.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Paul Mackerras <paulus@samba.org>
Linus Torvalds [Tue, 2 Oct 2007 17:35:28 +0000 (10:35 -0700)]
Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Fix missing load-twin usage in Niagara-1 memcpy.
[SPARC64]: Fix put_user() calls in binfmt_aout32.c
[SPARC]: Fix EBUS use of uninitialized variable.
Linus Torvalds [Tue, 2 Oct 2007 17:34:49 +0000 (10:34 -0700)]
Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[IEEE80211]: avoid integer underflow for runt rx frames
[TCP]: secure_tcp_sequence_number() should not use a too fast clock
[SFQ]: Remove artificial limitation for queue limit.
Dale Farnsworth [Mon, 1 Oct 2007 23:02:18 +0000 (16:02 -0700)]
mv643xx_eth: Do not modify struct netdev tx_queue_len
This driver erroneously zeros dev->tx_queue_len, since
mp->tx_ring_size has not yet been initialized. Actually,
the driver shouldn't modify tx_queue_len at all and should
leave the value set by alloc_etherdev(), currently 1000.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Linas Vepstas [Thu, 9 Aug 2007 23:27:00 +0000 (09:27 +1000)]
[POWERPC] pseries: device node status can be "ok" or "okay"
It seems that some versions of firmware will report a device
node status as the string "okay". As we are not expecting this
string, the device node will be ignored by the EEH subsystem.
Which means EEH will not be enabled.
When EEH is not enabled, PCI errors will be converted into
Machine Check exceptions, and we'll have a very unhappy system.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
David S. Miller [Tue, 2 Oct 2007 08:03:09 +0000 (01:03 -0700)]
[SPARC64]: Fix missing load-twin usage in Niagara-1 memcpy.
For the case where the source is not aligned modulo 8
we don't use load-twins to suck the data in and this
kills performance since normal loads allocate in the
L1 cache (unlike load-twin) and thus big memcpys swipe
the entire L1 D-cache.
We need to allocate a register window to implement this
properly, but that actually simplifies a lot of things
as a nice side-effect.
Signed-off-by: David S. Miller <davem@davemloft.net>
[IEEE80211]: avoid integer underflow for runt rx frames
Reported by Chris Evans <scarybeasts@gmail.com>:
> The summary is that an evil 80211 frame can crash out a victim's
> machine. It only applies to drivers using the 80211 wireless code, and
> only then to certain drivers (and even then depends on a card's
> firmware not dropping a dubious packet). I must confess I'm not
> keeping track of Linux wireless support, and the different protocol
> stacks etc.
>
> Details are as follows:
>
> ieee80211_rx() does not explicitly check that "skb->len >= hdrlen".
> There are other skb->len checks, but not enough to prevent a subtle
> off-by-two error if the frame has the IEEE80211_STYPE_QOS_DATA flag
> set.
>
> This leads to integer underflow and crash here:
>
> if (frag != 0)
> flen -= hdrlen;
>
> (flen is subsequently used as a memcpy length parameter).
How about this?
Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 1 Oct 2007 20:58:36 +0000 (13:58 -0700)]
[TCP]: secure_tcp_sequence_number() should not use a too fast clock
TCP V4 sequence numbers are 32bits, and RFC 793 assumed a 250 KHz clock.
In order to follow network speed increase, we can use a faster clock, but
we should limit this clock so that the delay between two rollovers is
greater than MSL (TCP Maximum Segment Lifetime : 2 minutes)
Choosing a 64 nsec clock should be OK, since the rollovers occur every
274 seconds.
[SFQ]: Remove artificial limitation for queue limit.
This is followup to Patrick's patch. A little optimization to enqueue
routine allows to remove artificial limitation on queue length.
Plus, testing showed that hash function used by SFQ is too bad or even worse.
It does not even sweep the whole range of hash values.
Switched to Jenkins' hash.
Signed-off-by: Alexey Kuznetsov <kaber@ms2.inr.ac.ru> Signed-off-by: David S. Miller <davem@davemloft.net>
Andi Kleen [Mon, 1 Oct 2007 08:20:08 +0000 (01:20 -0700)]
x86_64: increase VDSO_TEXT_OFFSET for ancient binutils
For some reason old binutils genertate larger headers so increase the text
offset of the vdso to avoid linker errors.
Roland McGrath explains:
"There are extra symbols in the '.dynsym' section that are responsible
for the size difference (They also cause corresponding inflation in
'.gnu.version')
Older ld's wrongly generated these unneeded symbols in .dynsym. This
was fixed not all that long ago (2006); binutils-2.17.50.0.6 might be
the first fixed version, but I have not verified for sure where the
cutoff was.
The unneeded symbols et al from old ld add almost 700 bytes excess.
This limits fairly tightly the amount by which the actual text and
data in the vDSO can grow in the future without pushing the whole
file over 4kb. If it does grow later on, we should consider changing
the layout with a config option or something to pack it better
without that padding, when building the kernel with newer binutils."
Signed-off-by: Andi Kleen <ak@suse.de> Cc: Roland McGrath <roland@redhat.com> Cc: Badari Pulavarty <pbadari@us.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In a desperate attempt to get a changelog entry in 2.6.23, I took a look
into it.
It turns out we are passing a real and not a virtual irq into
get_irq_server. This works for the case where hwirq < NR_IRQS and we
set virq = hwirq. In my case however hwirq = 590082 and we try and
access irq_desc[590082], slightly past the end at 512 entries.
Lucky we ship lots of memory with our machines.
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Linus Torvalds [Mon, 1 Oct 2007 20:17:28 +0000 (13:17 -0700)]
Fix possible splice() mmap_sem deadlock
Nick Piggin points out that splice isn't being good about the mmap
semaphore: while two readers can nest inside each others, it does leave
a possible deadlock if a writer (ie a new mmap()) comes in during that
nesting.
Original "just move the locking" patch by Nick, replaced by one by me
based on an optimistic pagefault_disable(). And then Jens tested and
updated that patch.
Reported-by: Nick Piggin <npiggin@suse.de> Tested-by: Jens Axboe <jens.axboe@oracle.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Lachlan McIlroy says:
It tried to fix an issue where log replay is replaying an inode cluster
initialisation transaction that should not be replayed because the inode
cluster on disk is more up to date. Since we don't log file sizes (we
rely on inode flushing to get them to disk) then we can't just replay
all the transations in the log and expect the inode to be completely
restored. We lose file size updates. Unfortunately this fix is causing
more (serious) problems than it is fixing.
Calling handle_futex_death in exit_robust_list for the different robust
mutexes of a thread basically frees the mutex. Another thread might grab
the lock immediately which updates the next pointer of the mutex.
fetch_robust_entry over the next pointer might therefore branch into the
robust mutex list of a different thread. This can cause two problems: 1)
some mutexes held by the dead thread are not getting freed and 2) some
mutexs held by a different thread are freed.
The next point need to be read before calling handle_futex_death.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Acked-by: Ingo Molnar <mingo@elte.hu> Acked-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Samuel Ortiz [Mon, 1 Oct 2007 08:20:12 +0000 (01:20 -0700)]
VT ioctl race fix
When calling the RELDISP VT ioctl, we are reading vt_newvt while the
console workqueue could be messing with it (through change_console()). We
fix this race by taking the console semaphore before reading vt_newvt.
Signed-off-by: Samuel Ortiz <sameo@openedhand.com> Acked-by: Antonino Daplas <adaplas@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mark Lord [Mon, 1 Oct 2007 08:20:10 +0000 (01:20 -0700)]
Fix SMP poweroff hangs
We need to disable all CPUs other than the boot CPU (usually 0) before
attempting to power-off modern SMP machines. This fixes the
hang-on-poweroff issue on my MythTV SMP box, and also on Thomas Gleixner's
new toybox.
Signed-off-by: Mark Lord <mlord@pobox.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> Cc: "Rafael J. Wysocki" <rjw@sisk.pl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ralf Baechle [Mon, 1 Oct 2007 08:20:10 +0000 (01:20 -0700)]
hugetlb: fix clear_user_highpage arguments
The virtual address space argument of clear_user_highpage is supposed to be
the virtual address where the page being cleared will eventually be mapped.
This allows architectures with virtually indexed caches a few clever
tricks. That sort of trick falls over in painful ways if the virtual
address argument is wrong.
projects / linux-2.6 / log