Hans Verkuil [Sat, 25 Nov 2006 12:40:28 +0000 (09:40 -0300)]
V4L/DVB (4885): Improve saa711x check
The old code would accept any device on the same i2c address as the
saa711x chips as an saa711x. However, this fails with saa717x chips,
which use that same address and so are misdetected as a saa7111. Now
check whether the chip is really a saa711x model.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Ira Snyder [Mon, 20 Nov 2006 10:20:48 +0000 (07:20 -0300)]
V4L/DVB (4849): Add missing spin_unlock to saa6588 decoder driver
Sparse noticed a lock imbalance in read_from_buf(). Further inspection shows
that the lock should not be held when the function exits.
This adds a spin_unlock_irqrestore(), so that every exit path of the
read_from_buf() function is consistent. The unlock was missing on an error
path.
Signed-off-by: Ira W. Snyder <devel@irasnyder.com> Signed-off-by: Hans J. Koch <koch@hjk-az.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Oliver Endriss [Sun, 19 Nov 2006 05:15:37 +0000 (02:15 -0300)]
V4L/DVB (4840): Budget: diseqc_method module parameter for cards with subsystem-id 13c2:1003
New module parameter diseqc_method for cards with subsystem-id 13c2:1003.
- 0: unreliable method, can be used by all board revisions (default)
- 1: reliable method, works for newer board layouts only
The parameter has no effect for cards with other subsystem-ids.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Reimplement execvp for our purposes - after we call fork() it is fundamentally
unsafe to use the kernel allocator - current is not valid there. So we simply
pass to our modified execvp() a preallocated buffer. This fixes a real bug
and works very well in testing (I've seen indirectly warning messages from the
forked thread - they went on the pipe connected to its stdout and where read
as a number by UML, when calling read_output(). I verified the obtained
number corresponded to "BUG:").
The added use of __cant_sleep() is not a new bug since __cant_sleep() is
already used in the same function - passing an atomicity parameter would be
better but it would require huge change, stating that this function must not
be called in atomic context and can sleep is a better idea (will make sure of
this gradually).
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Acked-by: Jeff Dike <jdike@addtoit.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[akpm@osdl.org: two compile fixes] Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Jiri Kosina <jikos@jikos.cz> Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Acked-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Alexey Dobriyan [Sat, 25 Nov 2006 19:09:36 +0000 (11:09 -0800)]
[PATCH] Enforce "unsigned long flags;" when spinlocking
Make it break or warn if you pass to spin_lock_irqsave() and friends
something different from "unsigned long flags;". Suprisingly large amount
of these was caught by recent commit c53421b18f205c5f97c604ae55c6a921f034b0f6 and others.
Idea is largely from FRV typechecking. Suggestions from Andrew Morton.
All stupid typos in first version fixed.
Passes allmodconfig on i386, x86_64, alpha, arm as well as my usual config.
Note #1: checking with sparse is still needed, because a driver can save
and pass around flags or something. So far patch is very intrusive.
Note #2: techically, we should break only if
sizeof(flags) < sizeof(unsigned long),
however, the more pain for getting suspicious code into kernel,
the better.
Jeremy Higdon [Sat, 25 Nov 2006 19:09:33 +0000 (11:09 -0800)]
[PATCH] sgiioc4: Disable module unload
This patch removes a module_exit function that sgiioc4 should not have had.
It seems that the IDE layer doesn't support submodule unloading. sgiioc4 was
the only driver in drivers/ide/pci that had an exit function. After an
unload, the devices would stay around and the next attempt to reference would
crash...
Signed-off-by: Jeremy Higdon <jeremy@sgi.com> Acked-by: "Bartlomiej Zolnierkiewicz" <bzolnier@gmail.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Roman Zippel [Sat, 25 Nov 2006 19:09:32 +0000 (11:09 -0800)]
[PATCH] fix menuconfig colours with TERM=vt100
On Mon, 13 Nov 2006, Phil Oester wrote:
> In commit 350b5b76384e77bcc58217f00455fdbec5cac594, the default menuconfig
> color scheme was changed to bluetitle. This breaks the highlighting
> of the selected item for me with TERM=vt100. The only way I can see
> which item is selected is via:
>
> make MENUCONFIG_COLOR=mono menuconfig
>
> Which restores the pre-2.6.19 white on black highlighting.
Fix.
Cc: Phil Oester <kernel@linuxace.com> Signed-off-by: Roman Zippel <zippel@linux-m68k.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
David Brownell [Sat, 25 Nov 2006 19:09:28 +0000 (11:09 -0800)]
[PATCH] rtc class locking bugfixes
I got a lockdep warning when running "rtctest" so I though it'd be good
to see what was up.
- The warning was for rtc->irq_task_lock, gotten from rtc_update_irq()
by irq handlerss ... but in a handful of other cases, grabbed without
blocking IRQs.
- Some callers to rtc_update_irq() were not ensuring IRQs were blocked,
yet the routine expects that; make sure all callers block IRQs.
It would appear that RTC API tests haven't been part of anyone's kernel
regression test suite recently, at least not with lockdep running.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
David Brownell [Sat, 25 Nov 2006 19:09:27 +0000 (11:09 -0800)]
[PATCH] rtc framework handles periodic irqs
The RTC framework has an irq_set_freq() method that should be used to manage
the periodic IRQ frequency, but the current ioctl logic doesn't know how to do
that. This patch teaches it how.
This means that drivers implementing irq_set_freq() will automatically support
RTC_IRQP_{READ,SET} ioctls; that logic doesn't need duplication within the
driver.
[akpm@osdl.org: export rtc_irq_set_freq] Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This updates the RTC documentation to summarize the two APIs now available:
the old PC/AT one, and the new RTC class drivers. It also updates the
included "rtctest.c" file to better meet Linux style guidelines, and to work
with the new RTC drivers.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Miklos Szeredi [Sat, 25 Nov 2006 19:09:20 +0000 (11:09 -0800)]
[PATCH] fuse: fix Oops in lookup
Fix bug in certain error paths of lookup routines. The request object was
reused for sending FORGET, which is illegal. This bug could cause an Oops
in 2.6.18. In earlier versions it might silently corrupt memory, but this
is very unlikely.
These error paths are never triggered by libfuse, so this wasn't noticed
even with the 2.6.18 kernel, only with a filesystem using the raw kernel
interface.
Thanks to Russ Cox for the bug report and test filesystem.
Thomas Chou [Sat, 25 Nov 2006 19:09:18 +0000 (11:09 -0800)]
[PATCH] initramfs: handle more than one source dir or file list
Fix bug 7401.
Handle more than one source dir or file list to the initramfs gen scripts.
The Kconfig help for INITRAMFS_SOURCE claims that you can specify multiple
space-separated sources in order to allow unprivileged users to build an
image. There are two bugs in the current implementation that prevent this
from working.
First, we pass "file1 dir2" to the gen_initramfs_list.sh script, which it
obviously can't open.
Second, gen_initramfs_list.sh -l outputs multiple definitions for
deps_initramfs -- one for each argument.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Cc: Sam Ravnborg <sam@ravnborg.org> Acked-by: Matthew Wilcox <matthew@wil.cx> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Mel Gorman [Thu, 23 Nov 2006 12:01:41 +0000 (12:01 +0000)]
[PATCH] x86_64: fix bad page state in process 'swapper'
find_min_pfn_for_node() and find_min_pfn_with_active_regions() both
depend on a sorted early_node_map[]. However, sort_node_map() is being
called after fin_min_pfn_with_active_regions() in
free_area_init_nodes().
In most cases, this is ok, but on at least one x86_64, the SRAT table
caused the E820 ranges to be registered out of order. This gave the
wrong values for the min PFN range resulting in some pages not being
initialised.
This patch sorts the early_node_map in find_min_pfn_for_node(). It has
been boot tested on x86, x86_64, ppc64 and ia64.
Dave Jones [Thu, 23 Nov 2006 01:42:01 +0000 (20:42 -0500)]
[PATCH] Correct bound checking from the value returned from _PPC method.
processor_perflib.c::acpi_processor_ppc_notifier() check if the value
returned by the processor's _PPC method is 0 and return failed if so.
This is wrong since 0 indicate that the bios think the processor can go
to the highest frequency. This patch for example fix the HP NX 6125 to
allow its highest frequency to be available.
Signed-off-by: Bruno Ducrot <ducrot@poupinou.org> Cc: "Pallipadi, Venkatesh" <venkatesh.pallipadi@intel.com> Signed-off-by: Dave Jones <davej@redhat.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Linus Torvalds [Thu, 23 Nov 2006 17:17:16 +0000 (09:17 -0800)]
Merge branch 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 3941/1: [Jornada7xx] - Addition to MAINTAINERS
[ARM] 3942/1: ARM: comment: consistent_sync should not be called directly
[ARM] ebsa110: fix warnings generated by asm/arch/io.h
[ARM] 3933/1: Source drivers/ata/Kconfig
Manuel Lauss [Wed, 22 Nov 2006 13:51:32 +0000 (14:51 +0100)]
[PATCH] make au1xxx-ide compile again
The Au1xx IDE controller driver doesn't compile:
CC drivers/ide/mips/au1xxx-ide.o
/linux-2.6.19-rc6-work/drivers/ide/mips/au1xxx-ide.c:480: error: conflicting types for 'auide_ddma_tx_callback'
include2/asm/mach-au1x00/au1xxx_ide.h:174: error: previous declaration of 'auide_ddma_tx_callback' was here
/linux-2.6.19-rc6-work/drivers/ide/mips/au1xxx-ide.c:486: error: conflicting types for 'auide_ddma_rx_callback'
include2/asm/mach-au1x00/au1xxx_ide.h:176: error: previous declaration of 'auide_ddma_rx_callback' was here
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Thiemo Seufer [Thu, 16 Nov 2006 22:13:54 +0000 (22:13 +0000)]
[MIPS] Hack for SB1 cache issues
Removing flush_icache_page a while ago broke SB1 which was using an empty
flush_data_cache_page function. This glues things well enough so a more
efficient but also more intrusive solution can be found later.
Linus Torvalds [Wed, 22 Nov 2006 22:55:29 +0000 (14:55 -0800)]
[AGP] Allocate AGP pages with GFP_DMA32 by default
Not all graphic page remappers support physical addresses over the 4GB
mark for remapping, so while some do (the AMD64 GART always did, and I
just fixed the i965 to do so properly), we're safest off just forcing
GFP_DMA32 allocations to make sure graphics pages get allocated in the
low 32-bit address space by default.
AGP sub-drivers that really care, and can do better, could just choose
to implement their own allocator (or we could add another "64-bit safe"
default allocator for their use), but quite frankly, you're not likely
to care in practice.
So for now, this trivial change means that we won't be allocating pages
that we can't map correctly by mistake on x86-64.
[ On traditional 32-bit x86, this could never happen, because GFP_KERNEL
would never allocate any highmem memory anyway ]
Acked-by: Andi Kleen <ak@suse.de> Acked-by: Dave Jones <davej@redhat.com> Cc: Eric Anholt <eric@anholt.net> Cc: Keith Packard <keithp@keithp.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Dan Williams [Tue, 21 Nov 2006 21:57:23 +0000 (22:57 +0100)]
[ARM] 3942/1: ARM: comment: consistent_sync should not be called directly
/*
* Note: Drivers should NOT use this function directly, as it will break
* platforms with CONFIG_DMABOUNCE.
* Use the driver DMA support - see dma-mapping.h (dma_sync_*)
*/
Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linus Torvalds [Wed, 22 Nov 2006 17:37:54 +0000 (09:37 -0800)]
[AGP] Fix intel 965 AGP memory mapping function
This introduces a i965-specific "mask_memory()" function that knows
about the extended physical addresses that the i965 supports. This
allows us to correctly map in physical memory in the >4GB range into the
GTT.
Also simplify/clean-up the i965 case for the aperture sizing by just
returning the fixed 512kB size from "fetch_size()". We don't really
care that not all of the aperture may be visible - the only thing that
cares about the aperture size is the Intel "stolen memory" calculation,
which depends on the fixed size.
Cc: Keith Packard <keithp@keithp.com> Cc: Eric Anholt <eric@anholt.net> Cc: Dave Jones <davej@redhat.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Linus Torvalds [Wed, 22 Nov 2006 17:32:06 +0000 (09:32 -0800)]
Don't call "note_interrupt()" with irq descriptor lock held
This reverts commit f72fa707604c015a6625e80f269506032d5430dc, and solves
the problem that it tried to fix by simply making "__do_IRQ()" call the
note_interrupt() function without the lock held, the way everybody else
does.
It should be noted that all interrupt handling code must never allow the
descriptor actors to be entered "recursively" (that's why we do all the
magic IRQ_PENDING stuff in the first place), so there actually is
exclusion at that much higher level, even in the absense of locking.
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[TG3]: Add missing unlock in tg3_open() error path.
[IPV6]: Fix address/interface handling in UDP and DCCP, according to the scoping architecture.
[IRDA]: Lockdep fix.
[BLUETOOTH]: Fix unaligned access in hci_send_to_sock.
[XFRM]: nlmsg length not computed correctly in the presence of subpolicies
[XFRM]: Sub-policies broke policy events
[IGMP]: Fix IGMPV3_EXP() normalization bit shift value.
[Bluetooth] Ignore L2CAP config requests on disconnect
[Bluetooth] Always include MTU in L2CAP config responses
[Bluetooth] Check if RFCOMM session is still attached to the TTY
[Bluetooth] Handling pending connect attempts after inquiry
[Bluetooth] Attach low-level connections to the Bluetooth bus
[IPV6] IP6TUNNEL: Add missing nf_reset() on input path.
[IPV6] IP6TUNNEL: Delete all tunnel device when unloading module.
[IPV6] ROUTE: Do not enable router reachability probing in router mode.
[IPV6] ROUTE: Prefer reachable nexthop only if the caller requests.
[IPV6] ROUTE: Try to use router which is not known unreachable.
Kim Phillips [Wed, 22 Nov 2006 00:19:42 +0000 (18:19 -0600)]
[POWERPC] Fix ucc_geth of_device discovery on mpc832x
mpc832x, as in mpc8360, needs to explicitly find and create the
platform device for ucc_geth in 2.6.19. This code will likely be
readapted to Benh's new of_ methods for 2.6.20.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Ira W. Snyder [Wed, 22 Nov 2006 01:44:31 +0000 (17:44 -0800)]
[TG3]: Add missing unlock in tg3_open() error path.
Sparse noticed a locking imbalance in tg3_open(). This patch adds an
unlock to one of the error paths, so that tg3_open() always exits
without the lock held.
Signed-off-by: Ira W. Snyder <kernel@irasnyder.com> Signed-off-by: David S. Miller <davem@davemloft.net>
/* Careful for priority inversions here !
* irlmp->links is never taken while another IrDA
* spinlock is held, so we are safe. Jean II */
So, under the assumption the author was right, it just needs a lockdep
annotation.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Acked-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Jamal Hadi Salim [Sun, 19 Nov 2006 22:55:30 +0000 (14:55 -0800)]
[XFRM]: nlmsg length not computed correctly in the presence of subpolicies
I actually dont have a test case for these; i just found them by
inspection. Refer to patch "[XFRM]: Sub-policies broke policy events"
for more info
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca> Acked-by: Masahide NAKAMURA <nakam@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Jamal Hadi Salim [Sun, 19 Nov 2006 22:53:07 +0000 (14:53 -0800)]
[XFRM]: Sub-policies broke policy events
XFRM policy events are broken when sub-policy feature is turned on.
A simple test to verify this:
run ip xfrm mon on one window and add then delete a policy on another
window ..
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca> Acked-by: Masahide NAKAMURA <nakam@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Marcel Holtmann [Sat, 18 Nov 2006 21:15:20 +0000 (22:15 +0100)]
[Bluetooth] Ignore L2CAP config requests on disconnect
Any L2CAP connection in disconnecting state shall not response
to any further config requests from the remote side. So in case
such a request is received, ignore it.
Signed-off-by: Ville Tervo <ville.tervo@nokia.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Marcel Holtmann [Sat, 18 Nov 2006 21:15:00 +0000 (22:15 +0100)]
[Bluetooth] Always include MTU in L2CAP config responses
When sending a positive config response it shall include the actual
MTU to be used on this channel. This differs from the Bluetooth 1.1
specification where it was enough to acknowledge the config request.
Marcel Holtmann [Sat, 18 Nov 2006 21:14:05 +0000 (22:14 +0100)]
[Bluetooth] Attach low-level connections to the Bluetooth bus
To receive uvents for the low-level ACL and SCO links, they must be
assigned to a subsystem. It is enough to attach them to the already
established Bluetooth bus.
[IPV6] ROUTE: Try to use router which is not known unreachable.
Only routers in "FAILED" state should be considered unreachable.
Otherwise, we do not try to use speicific routes unless all least specific
routers are considered unreachable.
Vivek Goyal [Mon, 20 Nov 2006 16:29:09 +0000 (11:29 -0500)]
[PATCH] x86_64: Align data segment to PAGE_SIZE boundary
o Explicitly align data segment to PAGE_SIZE boundary otherwise depending on
config options and tool chain it might be placed on a non PAGE_SIZE aligned
boundary and vmlinux loaders like kexec fail when they encounter a
PT_LOAD type segment which is not aligned to PAGE_SIZE boundary.
Linus Torvalds [Mon, 20 Nov 2006 19:47:18 +0000 (11:47 -0800)]
Add "pure_initcall" for static variable initialization
This is a quick hack to overcome the fact that SRCU currently does not
allow static initializers, and we need to sometimes initialize those
things before any other initializers (even "core" ones) can do so.
Currently we don't allow this at all for modules, and the only user that
needs is right now is cpufreq. As reported by Thomas Gleixner:
"Commit b4dfdbb3c707474a2254c5b4d7e62be31a4b7da9 ("[PATCH] cpufreq:
make the transition_notifier chain use SRCU breaks cpu frequency
notification users, which register the callback > on core_init
level."
Cc: Thomas Gleixner <tglx@timesys.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Arjan van de Ven <arjan@infradead.org> Cc: Andrew Morton <akpm@osdl.org>, Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Randy Dunlap [Sun, 19 Nov 2006 06:19:41 +0000 (22:19 -0800)]
[PATCH] ftape: fix printk format warnings
Fix printk format warnings:
drivers/char/ftape/zftape/zftape-buffers.c:87: warning: format '%d' expects type
'int', but argument 3 has type 'size_t'
drivers/char/ftape/zftape/zftape-buffers.c:104: warning: format '%d' expects type
'int', but argument 3 has type 'size_t'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Yasunori Goto [Sun, 19 Nov 2006 06:19:40 +0000 (22:19 -0800)]
[PATCH] x86_64: fix memory hotplug build with NUMA=n
This is to fix compile error of x86-64 memory hotplug without any NUMA
option.
CC arch/x86_64/mm/init.o
arch/x86_64/mm/init.c:501: error: redefinition of 'memory_add_physaddr_to_nid'
include/linux/memory_hotplug.h:71: error: previous definition of 'memory_add_phys
addr_to_nid' was here
arch/x86_64/mm/init.c:509: error: redefinition of 'memory_add_physaddr_to_nid'
arch/x86_64/mm/init.c:501: error: previous definition of 'memory_add_physaddr_to_
nid' was here
I confirmed compile completion with !NUMA, (NUMA & !ACPI_NUMA),
or (NUMA & ACPI_NUMA).
Daniel Ritz [Sun, 19 Nov 2006 06:19:34 +0000 (22:19 -0800)]
[PATCH] pcmcia: fix 'rmmod pcmcia' with unbound devices
Having unbound PCMCIA devices: doing a 'find /sys' after a 'rmmod pcmcia'
gives an oops because the pcmcia_device is not unregisterd from the driver
core.
fixes bugzilla #7481
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Dominik Brodowski <linux@dominikbrodowski.net> Cc: Pavol Gono <Palo.Gono@gmail.com> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Martin Michlmayr [Thu, 16 Nov 2006 23:14:35 +0000 (00:14 +0100)]
[ARM] 3933/1: Source drivers/ata/Kconfig
ARM doesn't source drivers/Kconfig like most architectures do, so the
newly added drivers/ata is currently not made available on ARM. SATA
is used on some ARM machines, like the Thecus N2100, so we need to
source drivers/ata/Kconfig.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
David Weinehall [Sat, 18 Nov 2006 02:58:58 +0000 (03:58 +0100)]
[PATCH] Update my CREDITS entry
I moved from Sweden to Finland 2.5 years ago, thought it might be time
to update my CREDITS entry (simply removing the address completely
seemed the sanest option).
Signed-off-by: David Weinehall <tao@kernel.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We must NOT try to queue up notify handlers to another thread than the
normal ACPI execution thread, because the notifications on some systems
seem to just keep on accumulating until we run out of memory and/or
threads.
Keeping events within the one deferred execution thread automatically
throttles the events properly.
At least the Compaq N620c will lock up completely on the first thermal
event without this patch reverted.
Cc: David Brownell <david-b@pacbell.net> Cc: Len Brown <len.brown@intel.com> Cc: Alexey Starikovskiy <alexey.y.starikovskiy@linux.intel.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Linus Torvalds [Fri, 17 Nov 2006 19:14:56 +0000 (11:14 -0800)]
x86: be more careful when walking back the frame pointer chain
When showing the stack backtrace, make sure that we never accept not
only an unchanging frame pointer, but also a frame pointer that moves
back down the stack frame. It must always grow up (toward older stack
frames).
I doubt this has triggered, but a subtly corrupt stack with extremely
unlucky contents could cause us to loop forever on a bogus endless frame
pointer chain.
This review was triggered by much worse problems happening in some of
the other stack unwinding code.
Steven Rostedt found the bug: static_obj() check did not take
PERCPU_ENOUGH_ROOM into account, so in-module DEFINE_PER_CPU-area locks
were triggering this message.
Ingo Molnar [Fri, 17 Nov 2006 13:26:18 +0000 (14:26 +0100)]
[PATCH] i386/x86_64: ACPI cpu_idle_wait() fix
The scheduler on Andreas Friedrich's hyperthreading system stopped
working properly: the scheduler would never move tasks to another CPU!
The lask known working kernel was 2.6.8.
After a couple of attempts to corner the bug, the following smoking gun
was found:
a quick look at cpu_idle_wait() shows how broken that code is
on i386: it changes the init task's affinity map but never
restores it ...
and because all userspace tasks get forked by init, they all
inherited that single-CPU affinity mask. x86_64 cloned this
bug too.
Signed-off-by: Ingo Molnar <mingo@elte.hu> Cc: Andreas Friedrich <andreas.friedrich@fujitsu-siemens.com> Cc: Wolfgang Erig <Wolfgang.Erig@fujitsu-siemens.com> Cc: Andrew Morton <akpm@osdl.org> Cc: Adrian Bunk <bunk@stusta.de> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
this crash happened because it did not sanitize the dwarf2 data it
got, and got an unaligned stack pointer - which happily walked past
the process stack (and eventually reached the end of kernel memory
and pagefaulted there) due to this naive iteration condition:
I moved to a different town and my old snail-mail address is invalid
now. Also, there's no need at all to have any address like that in
the sources, so remove it completely.
Linus Torvalds [Fri, 17 Nov 2006 06:18:28 +0000 (22:18 -0800)]
Fix generic fb_ddc i2c edid probe msg
Benh points out that the msgs[0].flags entry never got initialized, and
since it's an automatic stack allocation, it could have any random
value, which is bad.
Rewrite the initializer to explicitly initialize all fields of the small
i2c_msg structure array we generate. Just to keep it all obvious, let's
handle msgs[1].buf in the same initializer while we're at it, instead of
initializing that one separately later.
When radeonfb was changed to use the new "generic" ddc, a bit of
code initializing the GPIO lines was lost, causing it to not work
if the firmware didn't configure them properly, which seems to
happen on some cards.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6:
aoe: Add forgotten NULL at end of attribute list in aoeblk.c
debugfs: check return value correctly
W1: ioremap balanced with iounmap
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: auerswald possible memleak fix
USB: ipaq: Add HTC Modem Support
USB: Fixed outdated usb_get_device_descriptor() documentation
usb-storage: Remove duplicated unusual_devs.h entries for Sony Ericsson P990i
USB: hid-core: Add quirk for new Apple keyboard/trackpad
USB Storage: unusual_devs.h entry for Sony Ericsson P990i
USB: correct keymapping on Powerbook built-in USB ISO keyboards
USB: OHCI: fix root-hub resume bug
USB: Fix UCR-61S2B unusual_dev entry
USB: ftdi driver pid for dmx-interfaces
USB: ftdi_sio: adds vendor/product id for a RFID construction kit
OHCI: disallow autostop when wakeup is not available
usb_get_device_descriptor() used to convert several descriptor fields to host
CPU's byte order. Now that it doesn't convert them anymore, update the
documentation to reflect this.
Sergey Vlasov [Mon, 6 Nov 2006 13:33:07 +0000 (16:33 +0300)]
usb-storage: Remove duplicated unusual_devs.h entries for Sony Ericsson P990i
For some reason the unusual_devs.h entry for Sony Ericsson P990i had
three identical copies in a wrong place in the file in addition to the
correct entry.
projects / linux-2.6 / log