David S. Miller [Tue, 14 Feb 2006 02:09:44 +0000 (18:09 -0800)]
[SPARC64]: More SUN4V PCI work.
Get bus range from child of PCI controller root nexus.
This is actually a hack, but the PCI-E bridge sitting
at the top of the PCI tree responds to PCI config cycles
for every device number, so best to just ignore it for now.
Preliminary PCI irq routing, needs lots of work.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 11 Feb 2006 08:29:34 +0000 (00:29 -0800)]
[SPARC64]: Simplify sun4v TLB handling using macros.
There was also a bug in sun4v_itlb_miss, it loaded the
MMU Fault Status base into %g3 instead of %g2.
This pointed out a fast path for TSB miss processing,
since we have %g2 with the MMU Fault Status base, we
can use that to quickly load up the PGD phys address.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 10 Feb 2006 23:39:51 +0000 (15:39 -0800)]
[SPARC64]: Use ASI_SCRATCHPAD address 0x0 properly.
This is where the virtual address of the fault status
area belongs.
To set it up we don't make a hypervisor call, instead
we call OBP's SUNW,set-trap-table with the real address
of the fault status area as the second argument. And
right before that call we write the virtual address into
ASI_SCRATCHPAD vaddr 0x0.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 10 Feb 2006 00:12:22 +0000 (16:12 -0800)]
[SPARC64]: Implement sun4v TSB miss handlers.
When we register a TSB with the hypervisor, so that it or hardware can
handle TLB misses and do the TSB walk for us, the hypervisor traps
down to these trap when it incurs a TSB miss.
Processing is simple, we load the missing virtual address and context,
and do a full page table walk.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 8 Feb 2006 10:53:50 +0000 (02:53 -0800)]
[SPARC64]: Sun4v interrupt handling.
Sun4v has 4 interrupt queues: cpu, device, resumable errors,
and non-resumable errors. A set of head/tail offset pointers
help maintain a work queue in physical memory. The entries
are 64-bytes in size.
Each queue is allocated then registered with the hypervisor
as we bring cpus up.
The two error queues each get a kernel side buffer that we
use to quickly empty the main interrupt queue before we
call up to C code to log the event and possibly take evasive
action.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 6 Feb 2006 06:27:28 +0000 (22:27 -0800)]
[SPARC64]: Sanitize %pstate writes for sun4v.
If we're just switching between different alternate global
sets, nop it out on sun4v. Also, get rid of all of the
alternate global save/restore in the OBP CIF trampoline code.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 6 Feb 2006 04:47:26 +0000 (20:47 -0800)]
[SPARC64]: Fill dead cycles on trap entry with real work.
As we save trap state onto the stack, the store buffer fills up
mid-way through and we stall for several cycles as the store buffer
trickles out to the L2 cache. Meanwhile we can do some privileged
register reads and other calculations, essentially for free.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 4 Feb 2006 08:10:01 +0000 (00:10 -0800)]
[SPARC64]: Refine register window trap handling.
When saving and restoing trap state, do the window spill/fill
handling inline so that we never trap deeper than 2 trap levels.
This is important for chips like Niagara.
The window fixup code is massively simplified, and many more
improvements are now possible.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 27 Feb 2006 07:27:19 +0000 (23:27 -0800)]
[SPARC64]: Refine code sequences to get the cpu id.
On uniprocessor, it's always zero for optimize that.
On SMP, the jmpl to the stub kills the return address stack in the cpu
branch prediction logic, so expand the code sequence inline and use a
code patching section to fix things up. This also always better and
explicit register selection, which will be taken advantage of in a
future changeset.
The hard_smp_processor_id() function is big, so do not inline it.
Fix up tests for Jalapeno to also test for Serrano chips too. These
tests want "jbus Ultra-IIIi" cases to match, so that is what we should
test for.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 3 Feb 2006 00:16:24 +0000 (16:16 -0800)]
[SPARC64]: Turn off TSB growing for now.
There are several tricky races involved with growing the TSB. So just
use base-size TSBs for user contexts and we can revisit enabling this
later.
One part of the SMP problems is that tsb_context_switch() can see
partially updated TSB configuration state if tsb_grow() is running in
parallel. That's easily solved with a seqlock taken as a writer by
tsb_grow() and taken as a reader to capture all the TSB config state
in tsb_context_switch().
Then there is flush_tsb_user() running in parallel with a tsb_grow().
In theory we could take the seqlock as a reader there too, and just
resample the TSB pointer and reflush but that looks really ugly.
Lastly, I believe there is a case with threads that results in a TSB
entry lock bit being set spuriously which will cause the next access
to that TSB entry to wedge the cpu (since the TSB entry lock bit will
never clear). It's either copy_tsb() or some bug elsewhere in the TSB
assembly.
Signed-off-by: David S. Miller <davem@davemloft.net>
The are distrupting, which by the sparc v9 definition means they
can only occur when interrupts are enabled in the %pstate register.
This never occurs in any of the trap handling code running at
trap levels > 0.
So just mark it as an unexpected trap.
This allows us to kill off the cee_stuff member of struct thread_info.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 1 Feb 2006 23:55:21 +0000 (15:55 -0800)]
[SPARC64]: Access TSB with physical addresses when possible.
This way we don't need to lock the TSB into the TLB.
The trick is that every TSB load/store is registered into
a special instruction patch section. The default uses
virtual addresses, and the patch instructions use physical
address load/stores.
We can't do this on all chips because only cheetah+ and later
have the physical variant of the atomic quad load.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 1 Feb 2006 02:35:05 +0000 (18:35 -0800)]
[SPARC64]: Don't clobber alt-global %g4 on window fixups.
If we are returning back to kernel mode, %g4 could be live
(for example, in the case where we window spill in the etrap
code). So do not change it's value if going back to kernel.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 1 Feb 2006 02:34:51 +0000 (18:34 -0800)]
[SPARC64]: Fix race in LOAD_PER_CPU_BASE()
Since we use %g5 itself as a temporary, it can get clobbered
if we take an interrupt mid-stream and thus cause end up with
the final %g5 value too early as a result of rtrap processing.
Set %g5 at the very end, atomically, to avoid this problem.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 1 Feb 2006 02:34:21 +0000 (18:34 -0800)]
[SPARC64]: Fix too early reference to %g6
%g6 is not necessarily set to current_thread_info()
at sparc64_realfault_common. So store the fault
code and address after we invoke etrap and %g6 is
properly set up.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 1 Feb 2006 02:33:00 +0000 (18:33 -0800)]
[SPARC64]: Fix bogus flush instruction usage.
Some of the trap code was still assuming that alternate
global %g6 was hard coded with current_thread_info().
Let's just consistently flush at KERNBASE when we need
a pipeline synchronization. That's locked into the TLB
and will always work.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 1 Feb 2006 02:31:20 +0000 (18:31 -0800)]
[SPARC64]: Add infrastructure for dynamic TSB sizing.
This also cleans up tsb_context_switch(). The assembler
routine is now __tsb_context_switch() and the former is
an inline function that picks out the bits from the mm_struct
and passes it into the assembler code as arguments.
setup_tsb_parms() computes the locked TLB entry to map the
TSB. Later when we support using the physical address quad
load instructions of Cheetah+ and later, we'll simply use
the physical address for the TSB register value and set
the map virtual and PTE both to zero.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 1 Feb 2006 02:31:06 +0000 (18:31 -0800)]
[SPARC64]: TSB refinements.
Move {init_new,destroy}_context() out of line.
Do not put huge pages into the TSB, only base page size translations.
There are some clever things we could do here, but for now let's be
correct instead of fancy.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 27 Feb 2006 07:24:22 +0000 (23:24 -0800)]
[SPARC64]: Elminate all usage of hard-coded trap globals.
UltraSPARC has special sets of global registers which are switched to
for certain trap types. There is one set for MMU related traps, one
set of Interrupt Vector processing, and another set (called the
Alternate globals) for all other trap types.
For what seems like forever we've hard coded the values in some of
these trap registers. Some examples include:
1) Interrupt Vector global %g6 holds current processors interrupt
work struct where received interrupts are managed for IRQ handler
dispatch.
2) MMU global %g7 holds the base of the page tables of the currently
active address space.
3) Alternate global %g6 held the current_thread_info() value.
Such hardcoding has resulted in some serious issues in many areas.
There are some code sequences where having another register available
would help clean up the implementation. Taking traps such as
cross-calls from the OBP firmware requires some trick code sequences
wherein we have to save away and restore all of the special sets of
global registers when we enter/exit OBP.
We were also using the IMMU TSB register on SMP to hold the per-cpu
area base address, which doesn't work any longer now that we actually
use the TSB facility of the cpu.
The implementation is pretty straight forward. One tricky bit is
getting the current processor ID as that is different on different cpu
variants. We use a stub with a fancy calling convention which we
patch at boot time. The calling convention is that the stub is
branched to and the (PC - 4) to return to is in register %g1. The cpu
number is left in %g6. This stub can be invoked by using the
__GET_CPUID macro.
We use an array of per-cpu trap state to store the current thread and
physical address of the current address space's page tables. The
TRAP_LOAD_THREAD_REG loads %g6 with the current thread from this
table, it uses __GET_CPUID and also clobbers %g1.
TRAP_LOAD_IRQ_WORK is used by the interrupt vector processing to load
the current processor's IRQ software state into %g6. It also uses
__GET_CPUID and clobbers %g1.
Finally, TRAP_LOAD_PGD_PHYS loads the physical address base of the
current address space's page tables into %g7, it clobbers %g1 and uses
__GET_CPUID.
Many refinements are possible, as well as some tuning, with this stuff
in place.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 1 Feb 2006 02:29:18 +0000 (18:29 -0800)]
[SPARC64]: Move away from virtual page tables, part 1.
We now use the TSB hardware assist features of the UltraSPARC
MMUs.
SMP is currently knowingly broken, we need to find another place
to store the per-cpu base pointers. We hid them away in the TSB
base register, and that obviously will not work any more :-)
Another known broken case is non-8KB base page size.
Also noticed that flush_tlb_all() is not referenced anywhere, only
the internal __flush_tlb_all() (local cpu only) is used by the
sparc64 port, so we can get rid of flush_tlb_all().
The kernel gets it's own 8KB TSB (swapper_tsb) and each address space
gets it's own private 8K TSB. Later we can add code to dynamically
increase the size of per-process TSB as the RSS grows. An 8KB TSB is
good enough for up to about a 4MB RSS, after which the TSB starts to
incur many capacity and conflict misses.
We even accumulate OBP translations into the kernel TSB.
Another area for refinement is large page size support. We could use
a secondary address space TSB to handle those.
Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-2.6 / log