David S. Miller [Mon, 4 Aug 2008 06:56:28 +0000 (23:56 -0700)]
sparc64: Call xcall_deliver() directly in some cases.
For these cases the callers make sure:
1) The cpus indicated are online.
2) The current cpu is not in the list of indicated cpus.
Therefore we can pass a pointer to the mask directly.
One of the motivations in this transformation is to make use of
"&cpumask_of_cpu(cpu)" which evaluates to a pointer to constant
data in the kernel and thus takes up no stack space.
Hopefully someone in the future will change the interface of
arch_send_call_function_ipi() such that it passes a const cpumask_t
pointer so that this will optimize ever further.
Signed-off-by: David S. Miller <davem@davemloft.net>
Tomas Winkler [Mon, 4 Aug 2008 08:00:47 +0000 (16:00 +0800)]
iwlwifi: grap nic access before accessing periphery registers
We need to grap nic access before accessing periphery registers.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlwifi: decrement rx skb counter in scan abort handler
This patch decrements rx skb counter in scan abort handler.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Mon, 4 Aug 2008 08:00:43 +0000 (16:00 +0800)]
iwlwifi: fix unhandled interrupt when HW rfkill is on
This patch fixes unhandled interrupt when HW rfkill is on during
devices start up. The behavior changes, now open is successful even
when rfkill is on. This is to align with the situation when rfkill
is set on after opening.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch optimizes memory allocation. The cmd member of
iwl_tx_queue was allocated previously as a continuous block
of memory. This patch allocates separate memory chunks for each command
and maps/unmaps these chunks in the run time.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Mon, 4 Aug 2008 08:00:39 +0000 (16:00 +0800)]
iwlwifi: HW bug fixes
This patch adds few HW bug fixes.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Sun, 3 Aug 2008 22:58:36 +0000 (17:58 -0500)]
p54: Fix potential concurrent access to private data
Experience with the rtl8187 driver has shown that mac80211 can make
calls to the config callback routine in rapid succession. This patch
creates a mutex that protects the private data in several of the routines
called by mac80211.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Sun, 3 Aug 2008 21:36:01 +0000 (23:36 +0200)]
rt2x00: Disable link tuning in rt2500usb
In the legacy rt2570 driver the link tuner was never
really called. And now the reason has finally become
apparent: It breaks TX capabilities
As soon as the device has been associated all following
TX frames will be queued in the hardware and never transmitted
to the air. Disabling sections of the link tuner did not
have the expected result, but completely disabling the
link tuner did have the right result (Both of my rt2570 devices
came back to life).
This should fix Fedora bug: 411481
v2: Fix typos
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sven Wegener [Fri, 1 Aug 2008 19:57:16 +0000 (21:57 +0200)]
iwlwifi: Don't use buffer allocated on the stack for led names
Having the buffer on the stack and even re-using it for all led devices is bad.
Not being able to resolve the name member of the led device structure to a
meaningful value leads to confusion during ad-hoc debugging and potential
breakage in the future, if we ever decide to access the name member outside of
the registration function. Move the buffer to our private per led device
structures so that it is accessible after registration.
A quick grep didn't yield any occurence of using the led device name parameter
outside of the led device registration function, so currently we should already
be safe for normal operation.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net> Cc: Richard Purdie <rpurdie@rpsys.net> Acked-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Daniel Drake [Sat, 19 Jul 2008 22:31:17 +0000 (23:31 +0100)]
mac80211: automatic IBSS channel selection
When joining an ad-hoc network, the user is currently required to specify
the channel. The network will not be joined otherwise, unless it happens
to be sitting on the currently active channel.
This patch implements automatic channel selection when the user has not
locked the interface onto a specific channel.
Signed-off-by: Daniel Drake <dsd@gentoo.org> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Sat, 19 Jul 2008 01:41:24 +0000 (04:41 +0300)]
iwlwifi: use dtim_period from association, and set listen_interval
This patch uses dtim_period from association, and sets the listen_interval.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlwifi: RS small compile warnings without CONFIG_IWLWIFI_DEBUG
iwl-agn-rs.c: In function 'rs_clear':
iwl-agn-rs.c:2405: warning: unused variable 'priv
Signed-off-by: Denis V. Lunev <den@openvz.org> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug in AGG flow:
u64 bitmap = 0;
bitmap |= 1 << 32 results to be 0xffffffff80000000.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Esti Kummer [Fri, 18 Jul 2008 05:53:07 +0000 (13:53 +0800)]
iwlwifi: set led register in disassociation
This patch sets the led register in disassociation flow according to
rf-kill state : off - in case of rf_kill, on - otherwise.
Signed-off-by: Esti Kummer <ester.kummer@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Fri, 18 Jul 2008 05:53:06 +0000 (13:53 +0800)]
iwlwifi: kill iwl4965_fill_rs_info
iwl4965_fill_rs_info was used in sysfs. This info is already present
in iwl-agn-rs debugfs.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Fri, 18 Jul 2008 05:53:05 +0000 (13:53 +0800)]
iwlwifi: rename iwl-4695-rs to iwl-agn-rs
This patch renames iwl-4965-rs to iwl-agn-rs as it provides
rate scale capability for all AGN capable iwlwifi drivers.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Fri, 18 Jul 2008 05:53:04 +0000 (13:53 +0800)]
iwlwifi: move iwl4965_set_pwr_src to iwl4965-base.c
This patch moves iwl4965_set_pwr_src to iwl4965-base.c.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Fri, 18 Jul 2008 05:53:03 +0000 (13:53 +0800)]
iwlwifi: move beacon handling to iwl4965-base.c
This patch concentrates becaon handling in iwl4965-base.c.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Fri, 18 Jul 2008 05:53:02 +0000 (13:53 +0800)]
iwlwifi: move iwl4965_mac_ampdu_action to iwl4965-base.c
This patch moves iwl4965_mac_ampdu_action to iwl4965-base.c.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Fri, 18 Jul 2008 05:53:00 +0000 (13:53 +0800)]
mac80211: make listen_interval be limited by low level driver
This patch makes possible for a driver to specify maximal listen interval
The possibility for user to configure listen interval is not implemented
yet, currently the maximum provided by the driver or 1 is used.
Mac80211 uses config handler to set listen interval for to the driver.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds the dtim_period in ieee80211_bss_conf, this allows the low
level driver to know the dtim_period, and to plan power save accordingly.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Esti Kummer [Fri, 18 Jul 2008 05:52:58 +0000 (13:52 +0800)]
iwlwifi: corrects power_level in sysfs
This patch corrects power_level in sysfs.
Signed-off-by: Esti Kummer <ester.kummer@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohamed Abbas [Fri, 18 Jul 2008 05:52:57 +0000 (13:52 +0800)]
iwlwifi: add power save to 5000 HW
This patch adds support for power save for 5000 HW.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
zhangxiliang [Sat, 2 Aug 2008 02:56:37 +0000 (10:56 +0800)]
Re: [PATCH] Fix the kernel panic of audit_filter_task when key field is set
Sorry, I miss a blank between if and "(".
And I add "unlikely" to check "ctx" in audit_match_perm() and audit_match_filetype().
This is a new patch for it.
Signed-off-by: Zhang Xiliang <zhangxiliang@cn.fujitsu.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Paul Mundt [Mon, 4 Aug 2008 07:01:47 +0000 (16:01 +0900)]
nommu: Provide vmalloc_exec().
Now that SH has switched to vmalloc_exec() for PAGE_KERNEL_EXEC usage,
it's apparent that nommu has no vmalloc_exec() definition of its own.
Stub in the one from mm/vmalloc.c.
Takashi Yoshii [Mon, 4 Aug 2008 05:28:38 +0000 (14:28 +0900)]
add addrespace definition for sh2a.
Newfile: arch/sh/include/cpu-sh2a/cpu/addrspace.h
This file seems had be removed to use fallback (cpu-common/cpu/addrspace.h),
but, I'd like to add sh2a specific file here, because
1. the values defined there are not suitable for sh2a.
2. I don't think there is "common" definition for these values.
Values are chosen by consideration of followings...
P1 is 0. perhaps no question.
P2 is from hardware manual, which says no-cache area starts at 20000000.
It means that P? space size=20000000.
P3 is P2+size since asm/ptrace.h uses P3 as a end of P2.
P4 is P3+size since asm/fixup.h uses P4 as a end of P3.
Signed-off-by: Takashi YOSHII <yoshii.takashi@renesas.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Paul Mundt [Mon, 4 Aug 2008 05:18:53 +0000 (14:18 +0900)]
sh: Kill off ARCH_SUPPORTS_AOUT and remnants of a.out support.
SH never really supported a.out, so this was all just copied over blindly
from x86 way back when. As we don't reference linux/a.out.h anywhere in
the tree, these can now safely be killed off.
Avoid the overhead of atomic increment/decrement on each received packet.
This helps performance of non-NAPI devices (like loopback).
Use cleanup function to walk queue on each cpu and clean out any
left over packets.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Mon, 4 Aug 2008 04:15:59 +0000 (21:15 -0700)]
ipv6: Do not drop packet if skb->local_df is set to true
The old code will drop IPv6 packet if ipfragok is not set, since
ipfragok is obsoleted, will be instead by used skb->local_df, so this
check must be changed to skb->local_df.
This patch fix this problem and not drop packet if skb->local_df is
set to true.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Mon, 4 Aug 2008 04:15:08 +0000 (21:15 -0700)]
sctp: Drop ipfargok in sctp_xmit function
The ipfragok flag controls whether the packet may be fragmented
either on the local host on beyond. The latter is only valid on
IPv4.
In fact, we never want to do the latter even on IPv4 when PMTU is
enabled. This is because even though we can't fragment packets
within SCTP due to the prtocol's inherent faults, we can still
fragment it at IP layer. By setting the DF bit we will improve
the PMTU process.
RFC 2960 only says that we SHOULD clear the DF bit in this case,
so we're compliant even if we set the DF bit. In fact RFC 4960
no longer has this statement.
Once we make this change, we only need to control the local
fragmentation. There is already a bit in the skb which controls
that, local_df. So this patch sets that instead of using the
ipfragok argument.
The only complication is that there isn't a struct sock object
per transport, so for IPv4 we have to resort to changing the
pmtudisc field for every packet. This should be safe though
as the protocol is single-threaded.
Note that after this patch we can remove ipfragok from the rest
of the stack too.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Kumar Gala [Fri, 1 Aug 2008 16:44:11 +0000 (02:44 +1000)]
powerpc: Remove use of CONFIG_PPC_MERGE
Now that arch/ppc is gone and CONFIG_PPC_MERGE is always set, remove
the dead code associated with !CONFIG_PPC_MERGE from arch/powerpc
and include/asm-powerpc.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Followed by a few documentation/comment fixups and a couple of places
where <asm-powepc/...> was being used explicitly. Of the latter only
one was outside the arch code and it is a driver only built for powerpc.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
Yang Hongyang [Mon, 4 Aug 2008 01:16:15 +0000 (18:16 -0700)]
ipv6: Fix the return value of Set Hop-by-Hop options header with NULL data pointer
When Set Hop-by-Hop options header with NULL data
pointer and optlen is not zero use setsockopt(),
the kernel successfully return 0 instead of
return error EINVAL or EFAULT.
This patch fix the problem.
Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Adrian McMenamin [Wed, 30 Jul 2008 19:31:38 +0000 (12:31 -0700)]
maple: allow removal and reinsertion of keyboard driver module
Allow the removal (and subsequent reinsertion) of the maple_keyb (maple
keyboard) driver by adding a working removal function.
Also tidy long lines.
Signed-off-by: Adrian McMenamin <adrian@mcmen.demon.co.uk> Cc: Dmitry Torokhov <dtor@mail.ru> Cc: Paul Mundt <lethal@linux-sh.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Sven Wegener [Sun, 3 Aug 2008 21:06:44 +0000 (14:06 -0700)]
net: Add missing extra2 parameter for ip_default_ttl sysctl
Commit 76e6ebfb40a2455c18234dcb0f9df37533215461 ("netns: add namespace
parameter to rt_cache_flush") acceses the extra2 parameter of the
ip_default_ttl ctl_table, but it is never set to a meaningful
value. When e84f84f276473dcc673f360e8ff3203148bdf0e2 ("netns: place
rt_genid into struct net") is applied, we'll oops in
rt_cache_invalidate(). Set extra2 to init_net, to avoid that.
Reported-by: Marcin Slusarz <marcin.slusarz@gmail.com> Signed-off-by: Sven Wegener <sven.wegener@stealer.net> Tested-by: Marcin Slusarz <marcin.slusarz@gmail.com> Acked-by: Denis V. Lunev <den@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 3 Aug 2008 17:50:44 +0000 (10:50 -0700)]
Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: remove write-only variables from ext4_ordered_write_end
ext4: unexport jbd2_journal_update_superblock
ext4: Cleanup whitespace and other miscellaneous style issues
ext4: improve ext4_fill_flex_info() a bit
ext4: Cleanup the block reservation code path
ext4: don't assume extents can't cross block groups when truncating
ext4: Fix lack of credits BUG() when deleting a badly fragmented inode
ext4: Fix ext4_ext_journal_restart()
ext4: fix ext4_da_write_begin error path
jbd2: don't abort if flushing file data failed
ext4: don't read inode block if the buffer has a write error
ext4: Don't allow lg prealloc list to be grow large.
ext4: Convert the usage of NR_CPUS to nr_cpu_ids.
ext4: Improve error handling in mballoc
ext4: lock block groups when initializing
ext4: sync up block and inode bitmap reading functions
ext4: Allow read/only mounts with corrupted block group checksums
ext4: Fix data corruption when writing to prealloc area
In file included from arch/arm/mach-pxa/pcm990-baseboard.c:25:
include/linux/ide.h:645: error: 'CONFIG_IDE_MAX_HWIFS' undeclared here (not in a function)
Fix it by removing unneeded header include.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com> Cc: Tim Bird <tim.bird@am.sony.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
net: use software GSO for SG+CSUM capable netdevices
If a netdevice does not support hardware GSO, allowing the stack to
use GSO anyway and then splitting the GSO skb into MSS-sized pieces
as it is handed to the netdevice for transmitting is likely still
a win as far as throughput and/or CPU usage are concerned, since it
reduces the number of trips through the output path.
This patch enables the use of GSO on any netdevice that supports SG.
If a GSO skb is then sent to a netdevice that supports SG but does not
support hardware GSO, net/core/dev.c:dev_hard_start_xmit() will take
care of doing the necessary GSO segmentation in software.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Chris Larson [Sun, 3 Aug 2008 08:10:55 +0000 (01:10 -0700)]
net: fix missing pneigh entries in the neighbor seq_file code
When pneigh entries exist, but the user's read buffer isn't sufficient to
hold them all, one of the pneigh entries will be missing from the results.
In neigh_get_idx_any, the number of elements which neigh_get_idx
encountered is not correctly subtracted from the position number before
the call to pneigh_get_idx. neigh_get_idx reduces the position by 1 for
each call to neigh_get_next, but it does not reduce it by one for the
first element (neigh_get_first). The patch alters the neigh_get_idx and
pneigh_get_idx functions to subtract one from pos, for the first element,
when pos is non-zero.
Signed-off-by: Chris Larson <clarson@mvista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Chris Larson [Sun, 3 Aug 2008 08:02:41 +0000 (01:02 -0700)]
net: in the first call to neigh_seq_next, call neigh_get_first, not neigh_get_idx.
neigh_seq_next won't be called both with *pos > 0 && v ==
SEQ_START_TOKEN, so there's no point calling neigh_get_idx when we're
on the start token, just call neigh_get_first directly.
Signed-off-by: Chris Larson <clarson@mvista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Sat, 2 Aug 2008 21:33:18 +0000 (22:33 +0100)]
[ARM] Fix explicit asm(-arm)?/arch-foo references
No file should be explicitly referencing its own platform headers
by specifying an absolute include path. Fix these paths to use
standard <asm/arch/...> includes.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Marc Zyngier [Sat, 2 Aug 2008 17:12:23 +0000 (19:12 +0200)]
Fix IHEX firmware generation/loading
Fix both the IHEX firmware generation (len field always null, and EOF
marker a byte too short) and loading (struct ihex_binrec needs to be
packed to reflect the on-disk structure).
Signed-off-by: Marc Zyngier <maz@misterjones.org> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* git://git.infradead.org/users/dwmw2/random-2.6:
[MTD] Fix !CONFIG_BLOCK compile for mtdsuper.c
firmware: silence __fw_modbuild and __fw_modinst 'Nothing to be done' messages
Miklos Szeredi [Fri, 1 Aug 2008 18:28:47 +0000 (20:28 +0200)]
mm: dont clear PG_uptodate on truncate/invalidate
Brian Wang reported that a FUSE filesystem exported through NFS could
return I/O errors on read. This was traced to splice_direct_to_actor()
returning a short or zero count when racing with page invalidation.
However this is not FUSE or NFSD specific, other filesystems (notably
NFS) also call invalidate_inode_pages2() to purge stale data from the
cache.
If this happens while such pages are sitting in a pipe buffer, then
splice(2) from the pipe can return zero, and read(2) from the pipe can
return ENODATA.
The zero return is especially bad, since it implies end-of-file or
disconnected pipe/socket, and is documented as such for splice. But
returning an error for read() is also nasty, when in fact there was no
error (data becoming stale is not an error).
The same problems can be triggered by "hole punching" with
madvise(MADV_REMOVE).
Fix this by not clearing the PG_uptodate flag on truncation and
invalidation.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz> Acked-by: Nick Piggin <nickpiggin@yahoo.com.au> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Jens Axboe <jens.axboe@oracle.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Karsten Keil [Sat, 2 Aug 2008 14:35:53 +0000 (16:35 +0200)]
Fix remaining big endian issue of hfcmulti
The driver was not so bad at big endian at all, only the optimised fifo
read/write functions need a fix, with this fix the driver works on
a pegasus PPC machine.
Ivo van Doorn [Sat, 2 Aug 2008 08:31:09 +0000 (01:31 -0700)]
rt2x00: Fix compile warning
rt2x00usb_vendor_request_large_buff is write-only, so it is
safe to make the argument a const.
Fixes compile warning:
drivers/net/wireless/rt2x00/rt73usb.c: In function 'rt73usb_load_firmware':
drivers/net/wireless/rt2x00/rt73usb.c:916: warning: passing argument 5 of 'rt2x00usb_vendor_request_large_buff' discards qualifiers from pointer target typ
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Woodhouse [Fri, 1 Aug 2008 23:01:21 +0000 (00:01 +0100)]
[MTD] Fix !CONFIG_BLOCK compile for mtdsuper.c
As reported by Adrian Bunk, commit d5686b444ff3f72808d2b3fbd58672a86cdf38e7
(switch mtd and dm-table to lookup_bdev()) causes the following compile
error with CONFIG_BLOCK=n:
CC drivers/mtd/mtdsuper.o
drivers/mtd/mtdsuper.c: In function `get_sb_mtd':
drivers/mtd/mtdsuper.c:184: error: implicit declaration of function 'lookup_bdev'
drivers/mtd/mtdsuper.c:184: warning: assignment makes pointer from integer without a cast
drivers/mtd/mtdsuper.c:197: error: implicit declaration of function 'bdput'
make[3]: *** [drivers/mtd/mtdsuper.o] Error 1
Fix it by putting the block device lookup inside #ifdef CONFIG_BLOCK
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
David Woodhouse [Fri, 1 Aug 2008 22:58:36 +0000 (23:58 +0100)]
firmware: silence __fw_modbuild and __fw_modinst 'Nothing to be done' messages
People don't like them and think they're errors.
Leave the __fw_install one though; when 'make firmware_install' does
nothing, it's best to have a 'Nothing to be done for...' message rather
than just doing nothing.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Adrian Bunk [Fri, 1 Aug 2008 22:13:44 +0000 (01:13 +0300)]
sh: fix LIBGCC
Commit f15cbe6f1a4b4d9df59142fc8e4abb973302cf44
(sh: migrate to arch/sh/include/) moved KBUILD_CFLAGS
(which is used by LIBGCC) below LIBGCC, causing build
errors like the following:
<-- snip -->
...
LD .tmp_vmlinux1
arch/sh/kernel/built-in.o: In function `module_clk_recalc':
clock-sh4.c:(.text+0x80f0): undefined reference to `__udivsi3_i4i'
...
make[1]: *** [.tmp_vmlinux1] Error 1
<-- snip -->
Reported-by: Adrian Bunk <bunk@kernel.org> Signed-off-by: Adrian Bunk <bunk@kernel.org> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Paul Mundt [Fri, 1 Aug 2008 22:14:09 +0000 (07:14 +0900)]
sh: Revert the location change of auto-generated asm/machtypes.h
This ended up causing build breakage on O= builds, as reported by Adrian:
<-- snip -->
...
CC init/main.o
In file included from /home/bunk/linux/kernel-2.6/git/linux-2.6/arch/sh/include/asm/irq.h:4,
from /home/bunk/linux/kernel-2.6/git/linux-2.6/include/linux/irq.h:23,
from /home/bunk/linux/kernel-2.6/git/linux-2.6/arch/sh/include/asm/hardirq.h:5,
from /home/bunk/linux/kernel-2.6/git/linux-2.6/include/linux/hardirq.h:7,
from /home/bunk/linux/kernel-2.6/git/linux-2.6/include/asm-generic/local.h:5,
from /home/bunk/linux/kernel-2.6/git/linux-2.6/arch/sh/include/asm/local.h:4,
from /home/bunk/linux/kernel-2.6/git/linux-2.6/include/linux/module.h:19,
from /home/bunk/linux/kernel-2.6/git/linux-2.6/init/main.c:13:
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/sh/include/asm/machvec.h:15:27:
error: asm/machtypes.h: No such file or directory
make[2]: *** [init/main.o] Error 1
<-- snip -->
So we simply move machtypes.h back to its original place. asm-offsets.h is
still generated there regardless, until such a time that we find a better place
to stash auto-generated files.
Reported-by: Adrian Bunk <bunk@kernel.org> Signed-off-by: Paul Mundt <lethal@linux-sh.org>