Venki Pallipadi [Wed, 14 May 2008 23:05:51 +0000 (16:05 -0700)]
mprotect: prevent alteration of the PAT bits
There is a defect in mprotect, which lets the user change the page cache
type bits by-passing the kernel reserve_memtype and free_memtype
wrappers. Fix the problem by not letting mprotect change the PAT bits.
Eric Dumazet [Wed, 14 May 2008 23:05:51 +0000 (16:05 -0700)]
per_cpu: fix DEFINE_PER_CPU_SHARED_ALIGNED for modules
Current module loader lookups ".data.percpu" ELF section to perform
per_cpu relocation. But DEFINE_PER_CPU_SHARED_ALIGNED() uses another
section (".data.percpu.shared_aligned"), currently only handled in
vmlinux.lds, not by module loader.
To correct this problem, instead of adding logic into module loader, or
using at build time a module.lds file for all arches to group
".data.percpu.shared_aligned" into ".data.percpu", just use ".data.percpu"
for modules.
Alignment requirements are correctly handled by ld and module loader.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com> Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Fenghua Yu <fenghua.yu@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Geoff Levand [Wed, 14 May 2008 23:05:50 +0000 (16:05 -0700)]
memory_hotplug: check for walk_memory_resource() failure in online_pages()
Add a check to online_pages() to test for failure of
walk_memory_resource(). This fixes a condition where a failure
of walk_memory_resource() can lead to online_pages() returning
success without the requested pages being onlined.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com> Cc: Yasunori Goto <y-goto@jp.fujitsu.com> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Dave Hansen <haveblue@us.ibm.com> Cc: Keith Mannthey <kmannth@us.ibm.com> Cc: Christoph Lameter <clameter@sgi.com> Cc: Paul Jackson <pj@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tiger Yang [Wed, 14 May 2008 23:05:47 +0000 (16:05 -0700)]
ext3/4: fix uninitialized bs in ext3/4_xattr_set_handle()
This fix the uninitialized bs when we try to replace a xattr entry in
ibody with the new value which require more than free space.
This situation only happens we format ext3/4 with inode size more than 128 and
we have put xattr entries both in ibody and block. The consequences about
this bug is we will lost the xattr block which pointed by i_file_acl with all
xattr entires in it. We will alloc a new xattr block and put that large value
entry in it. The old xattr block will become orphan block.
Signed-off-by: Tiger Yang <tiger.yang@oracle.com> Cc: <linux-ext4@vger.kernel.org> Cc: Andreas Gruenbacher <agruen@suse.de> Acked-by: Andreas Dilger <adilger@sun.com> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Frysinger [Wed, 14 May 2008 23:05:42 +0000 (16:05 -0700)]
asm-{alpha,h8300,um,v850,xtensa}/param.h: unbreak HZ for userspace
I noticed this because alpha was broken due to the recent commit commit bdc807871d58285737d50dc6163d0feb72cb0dc2 ("avoid overflows in
kernel/time.c"). Most arches do something like this in their
asm/param.h:
A few arches though (namely alpha/h8300/um/v850/xtensa) either do no set
HZ at all for !__KERNEL__, or they set it wrongly. This should bring all
arches in line by setting up HZ for userspace.
Without this currently perl 5.10 doesn't build on alpha:
perl.c: In function 'perl_construct':
perl.c:388: error: 'CONFIG_HZ' undeclared (first use in this function)
-> http://buildd.debian.org/fetch.cgi?pkg=perl;ver=5.10.0-10;arch=alpha;stamp=1210252894
Signed-off-by: Mike Frysinger <vapier@gentoo.org> Cc: Richard Henderson <rth@twiddle.net> Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Cc: Jeff Dike <jdike@addtoit.com> Cc: Chris Zankel <chris@zankel.net> Cc: maximilian attems <max@stro.at> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[ HZ on alpha is 1024 for historical reasons. - Linus ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mingming Cao [Wed, 14 May 2008 23:05:41 +0000 (16:05 -0700)]
jbd: need to hold j_state_lock to updates to transaction t_state to T_COMMIT
Updating the current transaction's t_state is protected by j_state_lock. We
need to do the same when updating the t_state to T_COMMIT.
Signed-off-by: Mingming Cao <cmm@us.ibm.com> Acked-by: Jan Kara <jack@ucw.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Heiko Carstens [Wed, 14 May 2008 23:05:40 +0000 (16:05 -0700)]
memory hotplug: memmap_init_zone called twice
__add_zone calls memmap_init_zone twice if memory gets attached to an empty
zone. Once via init_currently_empty_zone and once explictly right after that
call.
Looks like this is currently not a bug, however the call is superfluous and
might lead to subtle bugs if memmap_init_zone gets changed. So make sure it
is called only once.
Nate Case [Wed, 14 May 2008 23:05:39 +0000 (16:05 -0700)]
ipmi: support I/O resources in OF driver
The current OF probing assumes that the resource is IORESOURCE_MEM. This
checks for the IORESOURCE_IO flag and behaves appropriately. An I/O resource
can exist with an ipmi device node on a legacy ISA bus.
Signed-off-by: Nate Case <ncase@xes-inc.com> Signed-off-by: Corey Minyard <cminyard@mvista.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nicolas Ferre [Wed, 14 May 2008 23:05:38 +0000 (16:05 -0700)]
atmel_lcdfb: fix initialization of a pre-allocated framebuffer
Fix initialization of framebuffer not calling ioremap_writecombine() function
and not using internal SRAM for at91sam9rl.
This is a little rework of the "Don't initialize a pre-allocated framebuffer"
patch that corrects the call to ioremap_writecombine() function.
It also cuts the use of internal SRAM for at91sam9rl : it is a bit small
for a framebuffer.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Andrew Victor <linux@maxim.org.za> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mm: fix fault vs invalidate race for linear mappings
Fix by reintroducing the wait_on_page_locked() after ->readpage() to make sure
the page is up-to-date before jumping back to the beginning of the function.
I've noticed this while testing nfs exporting on fuse. The patch
fixes it.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz> Cc: Nick Piggin <npiggin@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rene Herman [Wed, 14 May 2008 23:05:36 +0000 (16:05 -0700)]
pnp: add ISAPnP MPU option quirks
The AD181x and AZT230 chips don't support an IRQ-less MPU401 option but
work fine without one. This adds (priority functional) IRQ-less options
for each port option to help systems with few available IRQs.
The AD1815 quirk can't use pnp_register_irq_resource() due to doubly
penalizing the IRQ. Also, while not a practical issue due to no IRQ
option being present for the dependents, this needs to add in front, not
back.
Doesn't use pnp_register_port_resource() for symetry with above.
This does not delete the AD1815 independent option even though it should
be empty after the IRQ transfer due to AD1816 coming with an empty but
still present independent option by default.
Was tested on AD1815, AD1816 and AZT2320. The ALSA snd-ad1818a driver
also support the AZT2002 ID for MPU401 but this doesn't as I was unable to
test it.
Signed-off-by: Rene Herman <rene.herman@gmail.com> Tested-by: Uwe Bugla <uwe.bugla@gmx.de> Acked-by: Uwe Bugla <uwe.bugla@gmx.de> Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Cc: Takashi Iwai <tiwai@suse.de> Cc: Len Brown <len.brown@intel.com Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rene Herman [Wed, 14 May 2008 23:05:34 +0000 (16:05 -0700)]
pnp: add pnp_build_option() to the API
The subsequent AD181x quirk patch would like this as part of the API.
pnp_register_dependent_option() adds to the same dependent chain the quirk is
walking which is fairly unclean. This enables a private option chain build
which it can then just add onto the end when done.
Signed-off-by: Rene Herman <rene.herman@gmail.com> Tested-by: Uwe Bugla <uwe.bugla@gmx.de> Acked-by: Uwe Bugla <uwe.bugla@gmx.de> Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Cc: Takashi Iwai <tiwai@suse.de> Cc: Len Brown <len.brown@intel.com Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Extends the PLL frequency table of the AMD Geode-LX frame buffer driver to
make use of the DIV4 bit, thus adding support for dotclocks between 6 and 25
MHz. These are needed for small LCDs (e.g. 320x240). Also inserts some
intermediate steps between pre-existing frequencies.
The problem was the insertion of intermediate steps into the frequency
table; they would cause the wrong frequency to be matched. This patch
drops those intermediate frequencies while keeping the sub-25MHz
frequencies.
Signed-off-by: Andres Salomon <dilinger@debian.org> Signed-off-by: Jens Rottmann <JRottmann@LiPPERT-AT.de> Tested-by: Andres Salomon <dilinger@debian.org> Acked-by: Jordan Crouse <jordan.crouse@amd.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Eric Dumazet [Wed, 14 May 2008 23:05:31 +0000 (16:05 -0700)]
oprofile: don't request cache line alignment for cpu_buffer
Alignment was previously requested because cpu_buffer was an [NR_CPUS]
array, to avoid cache line sharing between CPUS.
After commit 608dfddd845da5ab6accef70154c8910529699f7 (oprofile: change
cpu_buffer from array to per_cpu variable ), we dont need to force an
alignement anymore since cpu_buffer sits in per_cpu zone.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com> Cc: Mike Travis <travis@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
cs5520: disable VDMA
ide/Kconfig: couple of fixes
alim15x3: remove WDC_ALI15X3 config option
alim15x3: add "wdc_udma" module parameter
alim15x3: remove stale warning about ATI RS100 northbridge
alim15x3: trivial cleanup for ali_set_pio_mode()
make ide-iops.c:SELECT_MASK() static
SWARM IDE: Fix up following changes to ide_hwif_t
Following recent changes to ide_hwif_t update the SWARM IDE driver to use
hw_regs_t to initialize port mapping. Plus minor layout adjustments along
the lines of other drivers.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Linus Torvalds [Wed, 14 May 2008 20:32:43 +0000 (13:32 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/cxgb3: Wrap the software send queue pointer as needed on flush
IB/ipath: Change ipath_devdata.ipath_sdma_status to be unsigned long
IB/ipath: Make ipath_portdata work with struct pid * not pid_t
IB/ipath: Fix RDMA read response sequence checking
IB/ipath: Fix many locking issues when switching to error state
IB/ipath: Fix RC and UC error handling
RDMA/nes: Fix up nes_lro_max_aggr module parameter
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-2.6:
Driver core: struct class remove children list
block: do_mounts - accept root=<non-existant partition>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (22 commits)
USB: atmel_usba_udc fixes, mostly disconnect()
USB: pxa27x_udc: minor fixes
usbtest: comment on why this code "expects" negative and positive errnos
USB: remove PICDEM FS USB demo (04d8:000c) device from ldusb
USB: option: add new Dell 5520 HSDPA variant
USB: unusual_devs: Add support for GI 0401 SD-Card interface
USB: serial gadget: descriptor cleanup
USB: serial gadget: simplify endpoint handling
USB: serial gadget: remove needless data structure
USB: serial gadget: cleanup/reorg
usb: fix compile warning in isp1760
USB: do not handle device 1410:5010 in 'option' driver
USB: Fix unusual_devs.h ordering
USB: add Zoom Telephonics Model 3095F V.92 USB Mini External modem to cdc-acm
USB: Support for the ET502HS HDSPA modem in option driver
USB: Support for the ET502HS HDSPA modem
usb: fix integer as NULL pointer warnings found by sparse
USB: isp1760: fix printk format
USB: add Telstra NextG CDMA id to option driver
USB: add association.h
...
Some devices, like md, may create partitions only at first access,
so allow root= to be set to a valid non-existant partition of an
existing disk. This applies only to non-initramfs root mounting.
This fixes a regression from 2.6.24 which did allow this to happen and
broke some users machines :(
Acked-by: Neil Brown <neilb@suse.de> Tested-by: Joao Luis Meloni Assirati <assirati@nonada.if.usp.br> Cc: stable <stable@kernel.org> Signed-off-by: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (73 commits)
net: Fix typo in net/core/sock.c.
ppp: Do not free not yet unregistered net device.
netfilter: xt_iprange: module aliases for xt_iprange
netfilter: ctnetlink: dump conntrack ID in event messages
irda: Fix a misalign access issue. (v2)
sctp: Fix use of uninitialized pointer
cipso: Relax too much careful cipso hash function.
tcp FRTO: work-around inorder receivers
tcp FRTO: Fix fallback to conventional recovery
New maintainer for Intel ethernet adapters
DM9000: Use delayed work to update MII PHY state
DM9000: Update and fix driver debugging messages
DM9000: Add __devinit and __devexit attributes to probe and remove
sky2: fix simple define thinko
[netdrvr] sfc: sfc: Add self-test support
[netdrvr] sfc: Increment rx_reset when reported as driver event
[netdrvr] sfc: Remove unused macro EFX_XAUI_RETRAIN_MAX
[netdrvr] sfc: Fix code formatting
[netdrvr] sfc: Remove kernel-doc comments for removed members of struct efx_nic
[netdrvr] sfc: Remove garbage from comment
...
Nick Piggin [Wed, 14 May 2008 04:37:36 +0000 (06:37 +0200)]
fix SMP data race in pagetable setup vs walking
There is a possible data race in the page table walking code. After the split
ptlock patches, it actually seems to have been introduced to the core code, but
even before that I think it would have impacted some architectures (powerpc
and sparc64, at least, walk the page tables without taking locks eg. see
find_linux_pte()).
The race is as follows:
The pte page is allocated, zeroed, and its struct page gets its spinlock
initialized. The mm-wide ptl is then taken, and then the pte page is inserted
into the pagetables.
At this point, the spinlock is not guaranteed to have ordered the previous
stores to initialize the pte page with the subsequent store to put it in the
page tables. So another Linux page table walker might be walking down (without
any locks, because we have split-leaf-ptls), and find that new pte we've
inserted. It might try to take the spinlock before the store from the other
CPU initializes it. And subsequently it might read a pte_t out before stores
from the other CPU have cleared the memory.
There are also similar races in higher levels of the page tables. They
obviously don't involve the spinlock, but could see uninitialized memory.
Arch code and hardware pagetable walkers that walk the pagetables without
locks could see similar uninitialized memory problems, regardless of whether
split ptes are enabled or not.
I prefer to put the barriers in core code, because that's where the higher
level logic happens, but the page table accessors are per-arch, and open-coding
them everywhere I don't think is an option. I'll put the read-side barriers
in alpha arch code for now (other architectures perform data-dependent loads
in order).
Signed-off-by: Nick Piggin <npiggin@suse.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nick Piggin [Wed, 14 May 2008 04:35:11 +0000 (06:35 +0200)]
read_barrier_depends arch fixlets
read_barrie_depends has always been a noop (not a compiler barrier) on all
architectures except SMP alpha. This brings UP alpha and frv into line with all
other architectures, and fixes incorrect documentation.
Signed-off-by: Nick Piggin <npiggin@suse.de> Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Brownell [Sun, 11 May 2008 05:46:38 +0000 (22:46 -0700)]
USB: atmel_usba_udc fixes, mostly disconnect()
Various fixes to Atmel's high speed UDC driver.
* Issue some missing disconnect() calls. Currently they are only made
when VBUS power goes away (on boards where the driver can sense such
changes), but that's not enough for gadget drivers to clean out all
the state that's needed. Missing calls were:
- After USB reset, before starting enumeration.
- When unregistering a gadget driver, before unbind().
* Don't assume gadget drivers provide disconnect callbacks; make sure
to not call through a null pointer!
* When the driver doesn't provide an unbind() callback, refuse to
unregister it.
Also remove two bogus "error" messages:
* Related to mis-handling of disconnect() ... don't emit error messages
for disconnect() handlers that disable endpoints. All of them should
be doing that; the problem is (unfixed) oddness in atmel_usba_udc.
* Don't emit a diagnostic for a curious and transient nonfatal error
that shows up sometimes with EP0.
Those messages spammed syslog, for no good reason.
Robert Jarzmik [Mon, 12 May 2008 17:47:56 +0000 (10:47 -0700)]
USB: pxa27x_udc: minor fixes
Minor fixes to pxa27x udc driver :
- don't clobber driver model bus_id field
- wrong endianess fix (no functional change; cpu is little-endian)
- double udc disable fix
- resume/suspend fix (OTG hold bit)
- make driver pxa27x dependant (check cpu at runtime)
Signed-off-by: Robert Jarzmik <rjarzmik@free.fr> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Marcin Slusarz [Mon, 12 May 2008 18:17:25 +0000 (20:17 +0200)]
usbtest: comment on why this code "expects" negative and positive errnos
On Mon, May 12, 2008 at 01:02:22AM -0700, David Brownell wrote:
> On Sunday 11 May 2008, Marcin Slusarz wrote:
> >
> > test_ctrl_queue expects (?) positive and negative errnos.
> > what is going on here?
>
> The sign is just a way to flag something:
>
> /* some faults are allowed, not required */
>
> The negative ones are required. Positive codes are optional,
> in the sense that, depending on how the peripheral happens
> to be implemented, they won't necessarily be triggered.
>
> For example, the test to fetch a device qualifier desriptor
> must succeed if the device is running at high speed. So that
> test is marked as negative. But when it's full speed, it
> could legitimately fail; marked as positive. And so on for
> other tests.
>
> Look at how the codes are *interpreted* to see it work.
Lets document it.
Based on comment from David Brownell <david-b@pacbell.net>.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Xiaofan Chen [Tue, 13 May 2008 13:52:00 +0000 (21:52 +0800)]
USB: remove PICDEM FS USB demo (04d8:000c) device from ldusb
Microchip has changed the PICDEM FS USB demo device (0x04d8:000c)
to use bulk transfer and not interrupt transfer. So I've updated the libusb
based program here (Post #31).
http://forum.microchip.com/tm.aspx?m=106426&mpage=2
So I believe that the in-kernel ldusb driver will no longer work with the
demo firmware. It should be removed.
Filip Aben [Thu, 8 May 2008 17:48:12 +0000 (10:48 -0700)]
USB: unusual_devs: Add support for GI 0401 SD-Card interface
Enables the SD-Card interface on the GI 0401 HSUPA card from Option.
The unusual_devs.h entry is necessary because the device descriptor is
vendor-specific. That prevents usb-storage from binding to it as an
interface driver.
This revised patch adds a small comment explaining why and reduces the
rev range.
David Brownell [Wed, 7 May 2008 21:27:37 +0000 (14:27 -0700)]
USB: serial gadget: descriptor cleanup
Bugfix some serial gadget descriptors:
- Stop mangling the low bits (controller type ID) of bcdDevice;
just use the high bits for a driver revision code.
- Serial numbers that aren't specific to individual devices
are useless; stop reporting "0" for this.
- Since it's not part of a CDC-conformant function, the "bulk only"
configuration shouldn't be using "CDC Data" as its interface class.
Switch over to using CLASS_VENDOR_SPEC (different value, 0xff).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Al Borchers <alborchers@steinerpoint.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Wed, 7 May 2008 21:25:24 +0000 (14:25 -0700)]
USB: serial gadget: simplify endpoint handling
Switch serial gadget away from a *very* old idiom: just remember
the endpoints we'll be using, instead of looking them up by name
each time. This is a net code and data (globals) shrink.
Also fix a small memory leak in the rmmod path, by working the
same as the disconnect code.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Al Borchers <alborchers@steinerpoint.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Wed, 7 May 2008 21:24:10 +0000 (14:24 -0700)]
USB: serial gadget: remove needless data structure
This removes a needless data structure from the serial gadget code;
it's a small code shrink, and a larger data shrink.
Since "struct usb_request" already has a "struct list_head" reserved
for use by gadget drivers, the serial gadget code doesn't need to
allocate wrapper structs to hold that list ... it can (and should!)
just use the list_head provided for that exact use.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Al Borchers <alborchers@steinerpoint.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Wed, 7 May 2008 23:00:36 +0000 (16:00 -0700)]
USB: serial gadget: cleanup/reorg
Some cleanup/reorg of g_serial ... simplifying it, and disentangling
its structure so morphing it into a "function" driver (combinable with
other interfaces) should be less painful.
- Remove most forward declarations
* put tty and gadget driver structs after their contents
* snug module init/exit decls next to their functions
* reordered some functions
- Other cleanup:
* convert a funky macro to an inline function
* snug up module params next to their declarations
* add missing driver.owner
* add separator lines between major driver sections
- Add comments re potential parameter/#define changes:
* only supports one port (shrank GS_NUM_PORTS)
* changing from 9600-8-N-1 affects multiple sites
- Remove net2280-specific optimization ... it was being done
way too late, can be done by net2280 module options, and in
any case doesn't matter at any sane serial data rates.
There are no behavioral changes, but the macro thing saves I-space.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Al Borchers <alborchers@steinerpoint.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After some time (ca. 5min) or if virtual CD is ejected, device id
changes to 1410:4400:
% lsusb -v -d 1410:4400 | grep InterfaceClass
bInterfaceClass 255 Vendor Specific Class
bInterfaceClass 255 Vendor Specific Class
Variable name says that 0x5010 is a Novatel U727, but searching in
internet shows, that this device also provides virtual CD that should be
ejected before use. Product id for serial port in this case is 0x4100.
Iain McFarlane [Sat, 3 May 2008 23:13:49 +0000 (00:13 +0100)]
USB: add Zoom Telephonics Model 3095F V.92 USB Mini External modem to cdc-acm
The patch below is a necessary workaround to support the Zoom Telephonics Model 3095F V.92 USB Mini External modem, which fails to initialise properly during normal probing thus:
May 3 22:53:00 imcfarla kernel: drivers/usb/class/cdc-acm.c: Zero length descriptor references
May 3 22:53:00 imcfarla kernel: cdc_acm: probe of 5-2:1.0 failed with error -22
Adding the patch below causes the probing section to be skipped, and the modem
then initialises correctly.
USB: Support for the ET502HS HDSPA modem in option driver
the proposed patch allows the ET502HS HDSPA modem to be handled by the
"option" driver. It has been tested for 1 month and works reliably (no
oopses, no hangs, 300KB/s throughput).
Harvey Harrison [Wed, 30 Apr 2008 22:03:41 +0000 (15:03 -0700)]
usb: fix integer as NULL pointer warnings found by sparse
drivers/usb/host/ohci-sm501.c:93:24: warning: Using plain integer as NULL pointer
drivers/usb/gadget/amd5536udc.c:3254:9: warning: Using plain integer as NULL pointer
drivers/usb/gadget/amd5536udc.c:3267:9: warning: Using plain integer as NULL pointer
drivers/usb/gadget/amd5536udc.c:3277:9: warning: Using plain integer as NULL pointer
drivers/usb/gadget/amd5536udc.c:3285:9: warning: Using plain integer as NULL pointer
drivers/usb/gadget/amd5536udc.c:3293:9: warning: Using plain integer as NULL pointer
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Randy Dunlap [Wed, 30 Apr 2008 20:53:54 +0000 (13:53 -0700)]
USB: isp1760: fix printk format
Fix printk format warnings in isp1760 (in linux-next):
next-20080430/drivers/usb/host/isp1760-hcd.c:994: warning: format '%d' expects type 'int', but argument 6 has type 'size_t'
next-20080430/drivers/usb/host/isp1760-hcd.c:1092: warning: format '%d' expects type 'int', but argument 3 has type 'size_t'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Wed, 30 Apr 2008 19:37:19 +0000 (15:37 -0400)]
USB: create attributes before sending uevent
This patch (as1087d) fixes a long-standing problem in usbcore: Device,
interface, and endpoint attributes aren't added until _after_ the
creation uevent has already been broadcast.
Unfortunately there are a few attributes which cannot be created that
early. The "descriptors" attribute is binary and so must be created
separately. The power-management attributes can't be created until
the dev/power/ group exists. And the interface string can vary from
one altsetting to another, so it has to be created dynamically.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Cc: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Phil Oester [Wed, 14 May 2008 06:27:48 +0000 (23:27 -0700)]
netfilter: xt_iprange: module aliases for xt_iprange
Using iptables 1.3.8 with kernel 2.6.25, rules which include '-m
iprange' don't automatically pull in xt_iprange module. Below patch
adds module aliases to fix that. Patch against latest -git, but seems
like a good candidate for -stable also.
Signed-off-by: Phil Oester <kernel@linuxace.com> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Leblond [Wed, 14 May 2008 06:27:11 +0000 (23:27 -0700)]
netfilter: ctnetlink: dump conntrack ID in event messages
Conntrack ID is not put (anymore ?) in event messages. This causes
current ulogd2 code to fail because it uses the ID to build a hash in
userspace. This hash is used to be able to output the starting time of
a connection.
Conntrack ID can be used in userspace application to maintain an easy
match between kernel connections list and userspace one. It may worth
to add it if there is no performance related issue.
[ Patrick: it was never included in events, but really should be ]
Signed-off-by: Eric Leblond <eric@inl.fr> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Wed, 14 May 2008 06:25:00 +0000 (23:25 -0700)]
sctp: Fix use of uninitialized pointer
Introduced by c4492586 (sctp: Add address type check while process
paramaters of ASCONF chunk):
net/sctp/sm_make_chunk.c: In function 'sctp_process_asconf':
net/sctp/sm_make_chunk.c:2828: warning: 'addr_param' may be used uninitialized in this function
net/sctp/sm_make_chunk.c:2828: note: 'addr_param' was declared here
Signed-off-by: Patrick McHardy <kaber@trash.net> Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Emelyanov [Wed, 14 May 2008 06:23:55 +0000 (23:23 -0700)]
cipso: Relax too much careful cipso hash function.
The cipso_v4_cache is allocated to contain CIPSO_V4_CACHE_BUCKETS
buckets. The CIPSO_V4_CACHE_BUCKETS = 1 << CIPSO_V4_CACHE_BUCKETBITS,
where CIPSO_V4_CACHE_BUCKETBITS = 7.
The bucket-selection function for this hash is calculated like this:
bkt = hash & (CIPSO_V4_CACHE_BUCKETBITS - 1);
^^^
i.e. picking only 4 buckets of possible 128 :)
Signed-off-by: Pavel Emelyanov <xemul@openvz.org> Acked-by: Paul Moore <paul.moore@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
V4L/DVB (7900): pvrusb: Fix Kconfig if DVB=m V4L_core=y
As reported by Ingo Molnar:
x86.git testing found the following build failure:
drivers/built-in.o: In function `pvr2_dvb_feed_thread':
pvrusb2-dvb.c:(.text+0x127e78): undefined reference to `dvb_dmx_swfilter'
drivers/built-in.o: In function `pvr2_dvb_adapter_exit':
pvrusb2-dvb.c:(.text+0x128357): undefined reference to `dvb_net_release'
pvrusb2-dvb.c:(.text+0x12836f): undefined reference to `dvb_dmxdev_release'
[...]
If one of DVB_CORE or VIDEO_DEV is a module, the modules that can be used by
both DVB and V4L cores should also be a module, otherwise, it will break its
dependencies. This Kconfig logic implements the following:
CONFIG_VIDEO_DEV CONFIG_DVB_CORE CONFIG_VIDEO_MEDIA
N N N
N M M
N Y Y
M N M
M M M
M Y M
Y N Y
Y M M
Y Y Y
Michael Krufky [Sat, 10 May 2008 17:34:09 +0000 (14:34 -0300)]
V4L/DVB (7893): xc5000: bug-fix: allow multiple devices in a single system
The current code passes a context pointer in the xc5000_config struct.
This context pointer is used in the tuner_callback function, used to
reset the device after firmware download.
The xc5000_config struct is a static structure, whose .priv member was
being assigned before calling xc5000_attach(). If there are more than
one of the same device type installed on a single system, the last one
to assign xc5000_config.priv will "win", and all others will cease to
function properly.
This patch passes the context pointer in xc5000_attach() rather that
storing it within the static struct xc5000_config.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Andy Walls [Mon, 12 May 2008 18:01:27 +0000 (15:01 -0300)]
V4L/DVB (7891): cx18/ivtv: fix open() kernel oops
Upon error conditions in cx18/ivtv_probe(), the code at the 'err:' label
leaves a NULL entry in cx18/ivtv_cards[]. This can cause a NULL pointer
de-reference in cx18/ivtv_v4l2_open() which is fixed by this patch.
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
V4L/DVB (7861): mt312: Prefix functions only with mt312_, Add zl10313 to kconfig description
This patch does some small cleanup to mt312.
It changes kconfig description to also list the ZL10313.
It does change some strange symbol names to be consistent with
module name mt312 and naming of all other functions in there.
* vp310_mt312_ops -> mt312_ops
* vp310_mt312_attach -> mt312_attach
Ingo Molnar [Mon, 5 May 2008 16:57:50 +0000 (13:57 -0300)]
V4L/DVB (7858): video: build fix for drivers/media/video/mt9v022.c
x86.git testing found the following build bug on latest -git:
CC [M] drivers/media/video/mt9v022.o
drivers/media/video/mt9v022.c: In function 'bus_switch_request':
drivers/media/video/mt9v022.c:199: error: implicit declaration of function 'gpio_is_valid'
drivers/media/video/mt9v022.c:201: error: implicit declaration of function 'gpio_request'
drivers/media/video/mt9v022.c:207: error: implicit declaration of function 'gpio_direction_output'
drivers/media/video/mt9v022.c:211: error: implicit declaration of function 'gpio_free'
drivers/media/video/mt9v022.c: In function 'bus_switch_act':
drivers/media/video/mt9v022.c:237: error: implicit declaration of function 'gpio_set_value_cansleep'
make[2]: *** [drivers/media/video] Error 2
make[1]: *** [drivers/media] Error 2
make[1]: *** Waiting for unfinished jobs....
make: *** [drivers] Error 2
the bug was that the driver uses GPIO functionality but only includes
the GPIO interface definitions for the CONFIG_MT9M001_PCA9536_SWITCH
case, which was not set in this config.
The quick fix seems to be to include linux/gpio.h unconditionally. (this
seems like a small cleanup as well as it removes and #ifdef is more
robust than an inclusion of asm/gpio.h) Not tested too much yet, so
please have another look in any case.
projects / linux-2.6 / log