Ctirad Fertr [Thu, 13 Dec 2007 15:27:13 +0000 (16:27 +0100)]
[ALSA] emu10k1 - 1616(M) cardbus improvements
This patch improves E-Mu 1616(M) cardbus support. It adds definitions of the
new Microdock and 1010 cardbus registers (thanks again for descriptions
James) and improves mixer for this card. Now you can use S/PDIF and ADAT on
Mirodock and also use headpohone output on host cardbus card as another
independent output.
Clemens Ladisch [Wed, 30 Jan 2008 07:38:30 +0000 (08:38 +0100)]
[ALSA] oxygen: revert SPI clock frequency change for AK4396/WM8785
While the AK4396 and WM8785 datasheets say that the SPI clock cycle
length must be at least 200 ns, 320 ns seems not to work reliably with
the controller, so we better use 160 ns.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Hermann Lauer [Wed, 30 Jan 2008 07:25:13 +0000 (08:25 +0100)]
[ALSA] es1938 - improve capture hw pointer reads
With the Solo1 (es1938) I got a lot of xrun's during capture on my machine.
Tracing that down it seems to be comming from reading ocassionaly bad hw
pointers from the chip. This patch uses more checking to avoid that false
pointer reads.
Failed reads are giving back the last good value read instead of spinning in
a tight loop, which seems more appropriate to me in an interrupt. I think I
saw this trick used in another driver
Signed-off-by: Hermann Lauer <Hermann.Lauer@iwr.uni-heidelberg.de> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Takashi Iwai [Mon, 28 Jan 2008 22:53:41 +0000 (23:53 +0100)]
[ALSA] Fix Oops with PCM OSS sync
The PCM OSS emulation can cause Oops at sync operation due to the wrong
data size calculation. Typically happening on Sparc64:
http://lkml.org/lkml/2008/1/24/426
Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Takashi Iwai [Mon, 28 Jan 2008 17:14:43 +0000 (18:14 +0100)]
[ALSA] hda-codec - Fix ALC262 HP-RP5700 model
Removed the PCM mixer elements conflicting with others.
Also renamed Master control to Headphone, which isn't a real master.
(The Master control is still created as a virtual master even after
this rename.)
Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Takashi Iwai [Mon, 28 Jan 2008 17:12:42 +0000 (18:12 +0100)]
[ALSA] hda-codec - Fix mixer controls with ALC262 HP T5735 model
The PCM mixer elements in HP T5735 model of ALC262 codec conflict
with Speaker and Headphone volumes. They should be removed.
Ditto for LineOut that is identical with Speaker.
Also, fixed/cleaned up the auto-mute callback to use the amp cache
correctly.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Takashi Iwai [Mon, 28 Jan 2008 11:30:17 +0000 (12:30 +0100)]
[ALSA] hda-codec - Add SPDIF output support to AD1986a laptop-eapd model
The SPDIF output on AD1986A laptop-eapd model is disabled although
some Samsung laptops have SPDIF output. Enable it after checking the
pin default config.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Matthew Ranostay [Fri, 25 Jan 2008 14:24:50 +0000 (15:24 +0100)]
[ALSA] hda: STAC92xx Line In/Mic as output check
This patch checks to see the Line In/Mic port have the ability
to do output before creating the the control switches.
The 92hd71bxx series of codecs has this issue with the port 0xe,
which only allows input.
Signed-off-by: Matthew Ranostay <mranostay@embededalley.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Takashi Iwai [Fri, 25 Jan 2008 10:35:17 +0000 (11:35 +0100)]
[ALSA] hda-codec - Add Conexant 5051 codec support
Added the support for Conexant 5051 audio codec.
Right now there are two preset models, laptop and hp.
The whole patch is based on the information from the base patch by
Linuxant.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Daniel Mack [Thu, 24 Jan 2008 17:46:42 +0000 (18:46 +0100)]
[ALSA] usb/caiaq: decrease period_bytes_min
This patch decreases the snd_pcm_hardware->period_bytes_min field in the
caiaq/usb audio driver. The hardware can actually handle as few as 128
bytes, depending on the system. So it makes no sense to keep
applications from actually using such values.
Signed-off-by: Daniel Mack <daniel@caiaq.de> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Andy Shevchenko [Thu, 24 Jan 2008 17:11:53 +0000 (18:11 +0100)]
[ALSA] fm801 - Add mute support for FM-only card with FM801 PCI to tuner bridge
This is improvement of the early support of the FM-only cards where the
fm801 chip represents the PCI to tuner bridge.
The tuner initialization isn't included the mute on as well as mute support
via V4L request. Proposed patch should fix this at least for 64-PCR model.
Signed-off-by: Andy Shevchenko <andy@smile.org.ua> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Takashi Iwai [Thu, 24 Jan 2008 14:31:36 +0000 (15:31 +0100)]
[ALSA] hda-codec - Fix handling of multiple capture streams
Fixed the bug that multiple capture streams conflict on Realtek codec
routines.
Also, this adds a framework to enable the alternative playback stream,
e.g. for VoIP. It's not fully implemented yet, though.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Randy Dunlap [Wed, 23 Jan 2008 10:52:38 +0000 (11:52 +0100)]
[ALSA] fix opti9xx/miro section mismatch
snd_opti93x_mixer() is only called by __devinit snd_opti93x_probe(),
so the former can also be __devinit.
snd_miro_mixer() is only called by __devinit snd_miro_probe(),
so the former can also be __devinit.
sound/isa/opti9xx/opti92x-ad1848.c:
WARNING: vmlinux.o(.text+0xf91cd7): Section mismatch: reference to .init.data:snd_opti93x_controls (between 'snd_opti93x_mixer' and 'snd_card_opti9xx_free')
WARNING: vmlinux.o(.text+0xf91d66): Section mismatch: reference to .init.data:snd_miro_controls (between 'snd_opti93x_mixer' and 'snd_card_opti9xx_free')
opti9xx/miro.c:
WARNING: vmlinux.o(.text+0xf926c2): Section mismatch: reference to .init.data:snd_miro_controls (between 'snd_miro_mixer' and 'snd_legacy_find_free_ioport')
WARNING: vmlinux.o(.text+0xf926e5): Section mismatch: reference to .init.data:snd_miro_eq_controls (between 'snd_miro_mixer' and 'snd_legacy_find_free_ioport')
WARNING: vmlinux.o(.text+0xf926f9): Section mismatch: reference to .init.data:snd_miro_line_control (between 'snd_miro_mixer' and 'snd_legacy_find_free_ioport')
WARNING: vmlinux.o(.text+0xf92716): Section mismatch: reference to .init.data:snd_miro_amp_control (between 'snd_miro_mixer' and 'snd_legacy_find_free_ioport')
WARNING: vmlinux.o(.text+0xf9273e): Section mismatch: reference to .init.data:snd_miro_preamp_control (between 'snd_miro_mixer' and 'snd_legacy_find_free_ioport')
WARNING: vmlinux.o(.text+0xf92764): Section mismatch: reference to .init.data:snd_miro_capture_control (between 'snd_miro_mixer' and 'snd_legacy_find_free_ioport')
WARNING: vmlinux.o(.text+0xf92783): Section mismatch: reference to .init.data:snd_miro_radio_control (between 'snd_miro_mixer' and 'snd_legacy_find_free_ioport')
WARNING: vmlinux.o(.text+0xf9279a): Section mismatch: reference to .init.data:snd_miro_eq_controls (between 'snd_miro_mixer' and 'snd_legacy_find_free_ioport')
WARNING: vmlinux.o(.text+0xf927b9): Section mismatch: reference to .init.data:snd_miro_radio_control (between 'snd_miro_mixer' and 'snd_legacy_find_free_ioport')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Randy Dunlap [Wed, 23 Jan 2008 10:52:06 +0000 (11:52 +0100)]
[ALSA] fix cs5535 section mismatch
snd_cs5535audio_mixer() is only called by __devinit snd_cs5535audio_probe(),
so the mixer function can also be __devinit.
WARNING: vmlinux.o(.text+0xfdbba0): Section mismatch: reference to .init.data:ac97_quirks (between 'snd_cs5535audio_mixer' and 'process_bm0_irq')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Mark Brown [Wed, 23 Jan 2008 07:41:46 +0000 (08:41 +0100)]
[ALSA] ASoC documentation updates
Update the ASoC documentation. Along with minor formatting and grammar
cleanups it moves the ASoC overview into the present tense to reflect
the fact that it has now been merged.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Takashi Iwai [Tue, 22 Jan 2008 14:37:13 +0000 (15:37 +0100)]
[ALSA] hda-codec - Don't query widget parameter for invalid NID
Don't query a widget parameter for an invalid NID in get_wcaps() but
rather returns zero (i.e. no attribute).
The read to an non-existing widget may result in a fatal codec
communication error.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Marc Boucher [Tue, 22 Jan 2008 14:15:59 +0000 (15:15 +0100)]
[ALSA] hda-codec - Fix laptop models for Cxt5045
Change laptop models to three different models, laptop-hpsense,
laptop-micsense and laptop-hpmicsense. The first two correspond to
the old 'laptop' and 'fujitsu' models.
Reassigned the quirk table for the new models.
Signed-off-by: Marc Boucher <marc@linuxant.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Mark Brown [Mon, 21 Jan 2008 13:33:37 +0000 (14:33 +0100)]
[ALSA] Fix lockdep warning in ASoC machine probe
Don't take the codec mutex during machine probe until we have registered
with ALSA, fixing a lockdep warning reported by Dmitry Baryshkov. Cc: Dmitry Baryshkov <dbaryshkov@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Clemens Ladisch [Mon, 21 Jan 2008 07:53:30 +0000 (08:53 +0100)]
[ALSA] oxygen: add 192 kHz SPDIF input support
Change the oxygen_spdif_input_bits_changed() function so that clock
changes on the SPDIF input are correctly detected. This means that
sample rates greater than 96 kHz are now supported.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Clemens Ladisch [Mon, 21 Jan 2008 07:51:55 +0000 (08:51 +0100)]
[ALSA] oxygen: move model-specific data out of common header
Instead of having model-specific fields in the common struct oxygen, put
them into a private structure that is allocated together with the card
structure.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Clemens Ladisch [Mon, 21 Jan 2008 07:45:37 +0000 (08:45 +0100)]
[ALSA] oxygen: remove MIDI autodetection
The MIDI bit in the MISC register is set by default and cannot be used
to detect the presence of a MIDI port. Instead, add a parameter to the
oxygen_pci_probe() function so that model drivers can specify this.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Takashi Iwai [Fri, 18 Jan 2008 14:32:32 +0000 (15:32 +0100)]
[ALSA] hda-intel - Make azx_get_response() a bit more robust
In azx_[rirb_]get_response(), the timeout is checked at the end of the loop.
It's better to be checked just after the check of the RIRB index to avoid
a bogus error with a too long msleep().
Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Takashi Iwai [Fri, 18 Jan 2008 12:36:07 +0000 (13:36 +0100)]
[ALSA] ice1712, ice1724 - Code clean up
Clean up ice1712/ice1724 codes. The board-specific data is allocated
locally in each code instead of having an ungly union in struct ice1712.
Also, fix coding issues in prodigy_hifi.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Andrew Paprocki [Fri, 18 Jan 2008 11:51:11 +0000 (12:51 +0100)]
[ALSA] hda_proc - Add a number of new settings to proc codec output
This patch adds additional output to the /proc codec#X info.
The following pieces of information are added to the output:
- Balanced, L/R swap, trigger, impedance sense pin capabilities
- Vref pin capabilities
- Current Vref pin widget control setting
- Default configuration association, sequence, and misc bit test
- EAPD/BTL bits conveying balanced mode, EAPD, and L/R swap
- Power state modified to show state name as well as setting vs actual value
- GPIO parameter output on Audio Function Group, including enumeration of IO
pins which are indicated present (Any I and O pins are not output at this
time)
- Stripe and L/R swap widget capabilities
- All digital converter bits: enable, validity, validity config, preemphasis,
copyright, non-audio, professional, generation level, and content category
- Converter stream and channel values for in/out widgets
- SDI select value for in widgets
- Unsolicited response widget capability tag and enabled bit
- Delay widget capability value
- Processing widget capability benign bit and number of coefficients
- Realtek Define Registers: processing coefficient, coefficient index
[Also, fixed space/tab issues and make codes a bit more readable
-- Takashi]
Signed-off-by: Andrew Paprocki <andrew@ishiboo.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Jiang zhe [Thu, 17 Jan 2008 10:19:26 +0000 (11:19 +0100)]
[ALSA] hda-codec - Fix capture source for Cx5045 codec
For codec conexant 5045, I found that the name of 'Capture Source Items'
is different from the name of mixer.
The mixer is:
HDA_CODEC_VOLUME('Ext Mic Playback Volume', 0x17, 0x2, HDA_INPUT),
HDA_CODEC_MUTE('Ext Mic Playback Switch', 0x17, 0x2, HDA_INPUT),
But the capture source item is :
static struct hda_input_mux cxt5045_capture_source = {
.num_items = 2,
.items = {
{ 'IntMic', 0x1 },
{ 'LineIn', 0x2 },
}
};
I think that it's better to change the name of capture_source to avoid
misunderstanding.
Jiang Zhe [Thu, 17 Jan 2008 10:18:41 +0000 (11:18 +0100)]
[ALSA] hda-codec - New model for conexant 5045 codec to support benq r55e
The benq r55e laptop have 3 jacks on the front panel.
One for HP, one for Line In and one for Mic In.
This patch implemented a new model to support it.
[ALSA] hda-codec - remove 11c1:1040 from patch_si3054.c id list
Codec with id 11c1:1040 sitting on hda bus isn't si3054-compatible.
It should be removed from patch_si3054.c id list.
The detailed information
http://archives.linmodems.org/26457
From: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Takashi Iwai [Wed, 16 Jan 2008 15:09:47 +0000 (16:09 +0100)]
[ALSA] hda-intel - Add workarounds for STAC codecs
Some machines with STAC codecs seem to have problems (e.g. no audible
playback) when the delay in codec-read routine is too short.
I still don't figure out which command sequence causes this problem
(due to lack of test hardware), but it's known that increasing the
delay fixes. So, added a stupid workaround here temporarily...
Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
T. H. Huth [Wed, 16 Jan 2008 14:57:08 +0000 (15:57 +0100)]
[ALSA] snd-powermac: handle dead DMA transfers
This patch provides the snd-powermac sound driver with the ability to handle
dead DMA transfers. If a dead DMA transfer is detected, the driver now sets
up a new DMA transfer to continue with the sound output at the point where the
old transfer died.
This dead DMA transfer handling has become necessary with recent kernels on
certain G4 PowerMacs. Please refer to the following URLs for more information:
https://bugtrack.alsa-project.org/alsa-bug/view.php?id=3126
https://bugs.launchpad.net/ubuntu/+source/linux-source-2.6.20/+bug/87652
http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=436723
The patch is based on the dead DMA transfer handling code from the old dmasound
driver which can be found in the file sound/oss/dmasound/dmasound_awacs.c in
the Linux source code.
Signed-off-by: T. H. Huth <th.huth@googlemail.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Randy Dunlap [Wed, 16 Jan 2008 13:56:04 +0000 (14:56 +0100)]
[ALSA] sound: fix caiaq section mismatches
Fix section mismatch in caiaq: these __devinit functions can be
called at any time so they should not be __devinit.
WARNING: vmlinux.o(.text+0x10a8dae): Section mismatch: reference to .init.text:snd_usb_caiaq_audio_init (between 'setup_card' and 'create_card')
WARNING: vmlinux.o(.text+0x10a8dd6): Section mismatch: reference to .init.text:snd_usb_caiaq_midi_init (between 'setup_card' and 'create_card')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Randy Dunlap [Wed, 16 Jan 2008 13:55:42 +0000 (14:55 +0100)]
[ALSA] sound: fix rme9652 section mismatch
Fix section mismatch in hdsp: snd_hdsp_proc_init() can be called from
an ioctl at any time.
WARNING: vmlinux.o(.text+0x1089bc2): Section mismatch: reference to .init.text: (between 'snd_hdsp_create_alsa_devices' and 'snd_hdsp_free')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Randy Dunlap [Wed, 16 Jan 2008 13:55:07 +0000 (14:55 +0100)]
[ALSA] sound: fix atiixp section mismatch
Fix section mismatch in atiixp by making some functions __devinit.
WARNING: vmlinux.o(.text+0xfd9304): Section mismatch: reference to .init.data:atiixp_quirks (between 'ac97_probing_bugs' and 'snd_atiixp_codec_detect')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Randy Dunlap [Wed, 16 Jan 2008 13:54:46 +0000 (14:54 +0100)]
[ALSA] sound: fix ad1889 section mismatch
Fix section mismatch in ad1889 by renaming the pci_driver variable to a
whitelisted variable name.
WARNING: vmlinux.o(.data+0x2e5ff0): Section mismatch: reference to .init.text:snd_ad1889_probe (between 'ad1889_pci' and 'index')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Randy Dunlap [Wed, 16 Jan 2008 13:54:21 +0000 (14:54 +0100)]
[ALSA] sound: fix mts64 section mismatches
Fix section mismatches in mts64 by making a static variable __devinitdata.
WARNING: vmlinux.o(.data+0x2e33f0): Section mismatch: reference to .init.data:mts64_ctl_smpte_switch (between 'control.19929' and 'snd_mts64_rawmidi_output_ops')
WARNING: vmlinux.o(.data+0x2e33f8): Section mismatch: reference to .init.data:mts64_ctl_smpte_time_hours (between 'control.19929' and 'snd_mts64_rawmidi_output_ops')
WARNING: vmlinux.o(.data+0x2e3400): Section mismatch: reference to .init.data:mts64_ctl_smpte_time_minutes (between 'control.19929' and 'snd_mts64_rawmidi_output_ops')
WARNING: vmlinux.o(.data+0x2e3408): Section mismatch: reference to .init.data:mts64_ctl_smpte_time_seconds (between 'control.19929' and 'snd_mts64_rawmidi_output_ops')
WARNING: vmlinux.o(.data+0x2e3410): Section mismatch: reference to .init.data:mts64_ctl_smpte_time_frames (between 'control.19929' and 'snd_mts64_rawmidi_output_ops')
WARNING: vmlinux.o(.data+0x2e3418): Section mismatch: reference to .init.data:mts64_ctl_smpte_fps (between 'control.19929' and 'snd_mts64_rawmidi_output_ops')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Takashi Iwai [Tue, 15 Jan 2008 10:41:41 +0000 (11:41 +0100)]
[ALSA] hda-codec - Disable PCBEEP mixer element in test model
It turned out that the PCBEEP element (0x1d) is disabled on some hardwares
although it's defined in the datasheet. Because of the error at info of
this element, the mixer gets totally unusable.
Since the PCBEEP isn't that important feature, it's safer to disable this.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
projects / linux-2.6 / log