Bjorn Helgaas [Tue, 4 Mar 2008 18:56:48 +0000 (11:56 -0700)]
PCI: alpha: use generic pci_enable_resources()
Use the generic pci_enable_resources() instead of the arch-specific code.
Unlike this arch-specific code, the generic version:
- skips resources unless requested in "mask"
- skips ROM resources unless IORESOURCE_ROM_ENABLE is set
- checks for resource collisions with "!r->parent"
Bjorn Helgaas [Tue, 4 Mar 2008 18:56:47 +0000 (11:56 -0700)]
PCI: add generic pci_enable_resources()
Each architecture has its own pcibios_enable_resources() implementation.
These differ in many minor ways that have nothing to do with actual
architectural differences. Follow-on patches will make most arches
use this generic version instead.
This version is based on powerpc, which seemed most up-to-date. The only
functional difference from the x86 version is that this uses "!r->parent"
to check for resource collisions instead of "!r->start && r->end".
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: David Howells <dhowells@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Shaohua Li [Mon, 25 Feb 2008 01:46:41 +0000 (09:46 +0800)]
PCI: add PCI Express ASPM support
PCI Express ASPM defines a protocol for PCI Express components in the D0
state to reduce Link power by placing their Links into a low power state
and instructing the other end of the Link to do likewise. This
capability allows hardware-autonomous, dynamic Link power reduction
beyond what is achievable by software-only controlled power management.
However, The device should be configured by software appropriately.
Enabling ASPM will save power, but will introduce device latency.
This patch adds ASPM support in Linux. It introduces a global policy for
ASPM, a sysfs file /sys/module/pcie_aspm/parameters/policy can control
it. The interface can be used as a boot option too. Currently we have
below setting:
-default, BIOS default setting
-powersave, highest power saving mode, enable all available ASPM
state and clock power management
-performance, highest performance, disable ASPM and clock power
management
By default, the 'default' policy is used currently.
In my test, power difference between powersave mode and performance mode
is about 1.3w in a system with 3 PCIE links.
Note: some devices might not work well with aspm, either because chipset
issue or device issue. The patch provide API (pci_disable_link_state),
driver can disable ASPM for specific device.
Signed-off-by: Shaohua Li <shaohua.li@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Gary Hade [Fri, 8 Feb 2008 22:00:52 +0000 (14:00 -0800)]
PCI: Include PCI domain in PCI bus names on x86/x86_64
The PCI bus names included in /proc/iomem and /proc/ioports are
of the form 'PCI Bus #XX' where XX is the bus number. This patch
changes the naming to 'PCI Bus XXXX:YY' where XXXX is the domain
number and YY is the bus number. For example, PCI bus 14 in
domain 0 will show as 'PCI Bus 0000:14' instead of 'PCI Bus #14'.
This change makes the naming consistent with other architectures
such as ia64 where multiple PCI domain support has been around
longer.
Signed-off-by: Gary Hade <garyhade@us.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Yinghai Lu [Sun, 3 Feb 2008 06:24:47 +0000 (22:24 -0800)]
PCI: pcie AER: don't check _OSC when acpi is disabled
[PATCH] pcie AER: don't check _OSC when acpi is disabled
when acpi=off or pci=noacpi, get warning
AER service couldn't init device 0000:00:0a.0:pcie01 - no _OSC support
AER service couldn't init device 0000:00:0e.0:pcie01 - no _OSC support
AER service couldn't init device 0000:00:0f.0:pcie01 - no _OSC support
AER service couldn't init device 0000:80:0b.0:pcie01 - no _OSC support
AER service couldn't init device 0000:80:0e.0:pcie01 - no _OSC support
AER service couldn't init device 0000:80:0f.0:pcie01 - no _OSC support
so don't check _OSC in aer_osc_setup
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch finally removes the global list of PCI devices. We are
relying entirely on the list held in the driver core now, and do not
need a separate "shadow" list as no one uses it.
This function was obviously never being used since early 2.5 days as any
device that it would try to remove would never really be removed from
the system due to the PCI device list being held in the driver core, not
the general list of PCI devices.
As we have not had a single report of a problem here in 4 years, I think
it's safe to remove now.
This lets us check if the device is really added to the driver core or
not, which is what we need when walking some of the bus lists. The flag
is there in anticipation of getting rid of the other PCI device list,
which is what we used to check in this situation.
PCI: remove initial bios sort of PCI devices on x86
We currently keep 2 lists of PCI devices in the system, one in the
driver core, and one all on its own. This second list is sorted at boot
time, in "BIOS" order, to try to remain compatible with older kernels
(2.2 and earlier days). There was also a "nosort" option to turn this
sorting off, to remain compatible with even older kernel versions, but
that just ends up being what we have been doing from 2.5 days...
Unfortunately, the second list of devices is not really ever used to
determine the probing order of PCI devices or drivers[1]. That is done
using the driver core list instead. This change happened back in the
early 2.5 days.
Relying on BIOS ording for the binding of drivers to specific device
names is problematic for many reasons, and userspace tools like udev
exist to properly name devices in a persistant manner if that is needed,
no reliance on the BIOS is needed.
Matt Domsch and others at Dell noticed this back in 2006, and added a
boot option to sort the PCI device lists (both of them) in a
breadth-first manner to help remain compatible with the 2.4 order, if
needed for any reason. This option is not going away, as some systems
rely on them.
This patch removes the sorting of the internal PCI device list in "BIOS"
mode, as it's not needed at all anymore, and hasn't for many years.
I've also removed the PCI flags for this from some other arches that for
some reason defined them, but never used them.
This should not change the ordering of any drivers or device probing.
[1] The old-style pci_get_device and pci_find_device() still used this
sorting order, but there are very few drivers that use these functions,
as they are deprecated for use in this manner. If for some reason, a
driver rely on the order and uses these functions, the breadth-first
boot option will resolve any problem.
Cc: Matt Domsch <Matt_Domsch@dell.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This cleans up the search.c file, now using the pci list of devices that
are created for the driver core, instead of relying on our separate list
of devices. It's better to use the functions already created for this
kind of thing, instead of rolling our own all the time.
This work is done in anticipation of getting rid of that second list of
pci devices all together.
And it ends up saving code, always a nice benefit.
This also removes one compiler warning for when CONFIG_PCI_LEGACY is
enabled as we no longer internally use the deprecated functions anymore.
This removes the pci_get_device_reverse function as there should not be
any need to walk pci devices backwards anymore. All users of this call
are now gone from the tree, so it is safe to remove it.
PCI: remove pci_get_device_reverse from calgary driver
This isn't needed, we can just walk the devices in bus order with no
problems at all, as we really want to remove pci_get_device_reverse from
the kernel tree.
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
security: fix up documentation for security_module_enable
Security: Introduce security= boot parameter
Audit: Final renamings and cleanup
SELinux: use new audit hooks, remove redundant exports
Audit: internally use the new LSM audit hooks
LSM/Audit: Introduce generic Audit LSM hooks
SELinux: remove redundant exports
Netlink: Use generic LSM hook
Audit: use new LSM hooks instead of SELinux exports
SELinux: setup new inode/ipc getsecid hooks
LSM: Introduce inode_getsecid and ipc_getsecid hooks
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6.26: (1090 commits)
[NET]: Fix and allocate less memory for ->priv'less netdevices
[IPV6]: Fix dangling references on error in fib6_add().
[NETLABEL]: Fix NULL deref in netlbl_unlabel_staticlist_gen() if ifindex not found
[PKT_SCHED]: Fix datalen check in tcf_simp_init().
[INET]: Uninline the __inet_inherit_port call.
[INET]: Drop the inet_inherit_port() call.
SCTP: Initialize partial_bytes_acked to 0, when all of the data is acked.
[netdrvr] forcedeth: internal simplifications; changelog removal
phylib: factor out get_phy_id from within get_phy_device
PHY: add BCM5464 support to broadcom PHY driver
cxgb3: Fix __must_check warning with dev_dbg.
tc35815: Statistics cleanup
natsemi: fix MMIO for PPC 44x platforms
[TIPC]: Cleanup of TIPC reference table code
[TIPC]: Optimized initialization of TIPC reference table
[TIPC]: Remove inlining of reference table locking routines
e1000: convert uint16_t style integers to u16
ixgb: convert uint16_t style integers to u16
sb1000.c: make const arrays static
sb1000.c: stop inlining largish static functions
...
Add the security= boot parameter. This is done to avoid LSM
registration clashes in case of more than one bult-in module.
User can choose a security module to enable at boot. If no
security= boot parameter is specified, only the first LSM
asking for registration will be loaded. An invalid security
module name will be treated as if no module has been chosen.
LSM modules must check now if they are allowed to register
by calling security_module_enable(ops) first. Modify SELinux
and SMACK to do so.
Do not let SMACK register smackfs if it was not chosen on
boot. Smackfs assumes that smack hooks are registered and
the initial task security setup (swapper->security) is done.
Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com> Acked-by: James Morris <jmorris@namei.org>
Ahmed S. Darwish [Fri, 18 Apr 2008 23:59:43 +0000 (09:59 +1000)]
Audit: Final renamings and cleanup
Rename the se_str and se_rule audit fields elements to
lsm_str and lsm_rule to avoid confusion.
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com> Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com> Acked-by: James Morris <jmorris@namei.org>
SELinux: use new audit hooks, remove redundant exports
Setup the new Audit LSM hooks for SELinux.
Remove the now redundant exported SELinux Audit interface.
Audit: Export 'audit_krule' and 'audit_field' to the public
since their internals are needed by the implementation of the
new LSM hook 'audit_rule_known'.
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com> Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com> Acked-by: James Morris <jmorris@namei.org>
instad of (respectively) :
selinux_audit_rule_init
selinux_audit_rule_free
audit_rule_has_selinux
selinux_audit_rule_match
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com> Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com> Acked-by: James Morris <jmorris@namei.org>
Those hooks are only available if CONFIG_AUDIT is enabled.
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com> Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com> Acked-by: James Morris <jmorris@namei.org> Reviewed-by: Paul Moore <paul.moore@hp.com>
Remove the following exported SELinux interfaces:
selinux_get_inode_sid(inode, sid)
selinux_get_ipc_sid(ipcp, sid)
selinux_get_task_sid(tsk, sid)
selinux_sid_to_string(sid, ctx, len)
They can be substitued with the following generic equivalents
respectively:
new LSM hook, inode_getsecid(inode, secid)
new LSM hook, ipc_getsecid*(ipcp, secid)
LSM hook, task_getsecid(tsk, secid)
LSM hook, sid_to_secctx(sid, ctx, len)
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com> Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com> Acked-by: James Morris <jmorris@namei.org> Reviewed-by: Paul Moore <paul.moore@hp.com>
Don't use SELinux exported selinux_get_task_sid symbol.
Use the generic LSM equivalent instead.
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com> Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com> Acked-by: James Morris <jmorris@namei.org> Acked-by: David S. Miller <davem@davemloft.net> Reviewed-by: Paul Moore <paul.moore@hp.com>
Audit: use new LSM hooks instead of SELinux exports
Stop using the following exported SELinux interfaces:
selinux_get_inode_sid(inode, sid)
selinux_get_ipc_sid(ipcp, sid)
selinux_get_task_sid(tsk, sid)
selinux_sid_to_string(sid, ctx, len)
kfree(ctx)
and use following generic LSM equivalents respectively:
security_inode_getsecid(inode, secid)
security_ipc_getsecid*(ipcp, secid)
security_task_getsecid(tsk, secid)
security_sid_to_secctx(sid, ctx, len)
security_release_secctx(ctx, len)
Call security_release_secctx only if security_secid_to_secctx
succeeded.
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com> Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com> Acked-by: James Morris <jmorris@namei.org> Reviewed-by: Paul Moore <paul.moore@hp.com>
Setup the new inode_getsecid and ipc_getsecid() LSM hooks
for SELinux.
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com> Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com> Acked-by: James Morris <jmorris@namei.org> Reviewed-by: Paul Moore <paul.moore@hp.com>
LSM: Introduce inode_getsecid and ipc_getsecid hooks
Introduce inode_getsecid(inode, secid) and ipc_getsecid(ipcp, secid)
LSM hooks. These hooks will be used instead of similar exported
SELinux interfaces.
Let {inode,ipc,task}_getsecid hooks set the secid to 0 by default
if CONFIG_SECURITY is not defined or if the hook is set to
NULL (dummy). This is done to notify the caller that no valid
secid exists.
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com> Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com> Acked-by: James Morris <jmorris@namei.org> Reviewed-by: Paul Moore <paul.moore@hp.com>
[NET]: Fix and allocate less memory for ->priv'less netdevices
This patch effectively reverts commit d0498d9ae1a5cebac363e38907266d5cd2eedf89
aka "[NET]: Do not allocate unneeded memory for dev->priv alignment."
It was found to be buggy because of final unconditional += NETDEV_ALIGN_CONST
removal.
For example, for sizeof(struct net_device) being 2048 bytes, "alloc_size"
was also 2048 bytes, but allocator with debugging options turned on started
giving out !32-byte aligned memory resulting in redzones overwrites.
Patch does small optimization in ->priv'less case: bumping size to next
32-byte boundary was always done to ensure ->priv will also be aligned.
But, no ->priv, no need to do that.
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru> Signed-off-by: David S. Miller <davem@davemloft.net>
do not return a -EINVAL when mmap()-ing PCI holes.
Signed-off-by: Ingo Molnar <mingo@elte.hu> Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Acked-by: Suresh Siddha <suresh.b.siddha@intel.com> Acked-by: H. Peter Anvin <hpa@zytor.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Arjan van de Ven <arjan@linux.intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (137 commits)
[SCSI] iscsi: bidi support for iscsi_tcp
[SCSI] iscsi: bidi support at the generic libiscsi level
[SCSI] iscsi: extended cdb support
[SCSI] zfcp: Fix error handling for blocked unit for send FCP command
[SCSI] zfcp: Remove zfcp_erp_wait from slave destory handler to fix deadlock
[SCSI] zfcp: fix 31 bit compile warnings
[SCSI] bsg: no need to set BSG_F_BLOCK bit in bsg_complete_all_commands
[SCSI] bsg: remove minor in struct bsg_device
[SCSI] bsg: use better helper list functions
[SCSI] bsg: replace kobject_get with blk_get_queue
[SCSI] bsg: takes a ref to struct device in fops->open
[SCSI] qla1280: remove version check
[SCSI] libsas: fix endianness bug in sas_ata
[SCSI] zfcp: fix compiler warning caused by poking inside new semaphore (linux-next)
[SCSI] aacraid: Do not describe check_reset parameter with its value
[SCSI] aacraid: Fix down_interruptible() to check the return value
[SCSI] sun3_scsi_vme: add MODULE_LICENSE
[SCSI] st: rename flush_write_buffer()
[SCSI] tgt: use KMEM_CACHE macro
[SCSI] initio: fix big endian problems for auto request sense
...
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6: (43 commits)
firewire: cleanups
firewire: fix synchronization of gap counts
firewire: wait until PHY configuration packet was transmitted (fix bus reset loop)
firewire: remove unused struct member
firewire: use bitwise and to get reg in handle_registers
firewire: replace more hex values with defined csr constants
firewire: reread config ROM when device reset the bus
firewire: replace static ROM cache by allocated cache
firewire: fw-ohci: work around generation bug in TI controllers (fix AV/C and more)
firewire: fw-ohci: extend logging of bus generations and node ID
firewire: fw-ohci: conditionally log busReset interrupts
firewire: fw-ohci: don't append to AT context when it's not active
firewire: fw-ohci: log regAccessFail events
firewire: fw-ohci: make sure HCControl register LPS bit is set
firewire: fw-ohci: missing PPC PMac feature calls in failure path
firewire: fw-ohci: untangle a mixed unsigned/signed expression
firewire: debug interrupt events
firewire: fw-ohci: catch self_id_count == 0
firewire: fw-ohci: add self ID error check
firewire: fw-ohci: refactor probe, remove, suspend, resume
...
James Bottomley [Fri, 18 Apr 2008 18:18:48 +0000 (13:18 -0500)]
libata: fix boot panic with SATAPI devices on non-SFF HBAs
The kernel now panics reliably on boot if you have a SATAPI device
connected.
The problem was introduced by the libata merge trying to pull out all
the SFF code into a separate module. Unfortunately, if you're a satapi
device you usually need to call atapi_request_sense, which has a bare
invocation of a SFF callback which is NULL on non-SFF HBAs. Fix this by
making the call conditional.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2: (64 commits)
ocfs2/net: Add debug interface to o2net
ocfs2: Only build ocfs2/dlm with the o2cb stack module
ocfs2/cluster: Get rid of arguments to the timeout routines
ocfs2: Put tree in MAINTAINERS
ocfs2: Use BUG_ON
ocfs2: Convert ocfs2 over to unlocked_ioctl
ocfs2: Improve rename locking
fs/ocfs2/aops.c: test for IS_ERR rather than 0
ocfs2: Add inode stealing for ocfs2_reserve_new_inode
ocfs2: Add ac_alloc_slot in ocfs2_alloc_context
ocfs2: Add a new parameter for ocfs2_reserve_suballoc_bits
ocfs2: Enable cross extent block merge.
ocfs2: Add support for cross extent block
ocfs2: Move /sys/o2cb to /sys/fs/o2cb
sysfs: Allow removal of symlinks in the sysfs root
ocfs2: Reconnect after idle time out.
ocfs2/dlm: Cleanup lockres print
ocfs2/dlm: Fix lockname in lockres print function
ocfs2/dlm: Move dlm_print_one_mle() from dlmmaster.c to dlmdebug.c
ocfs2/dlm: Dumps the purgelist into a debugfs file
...
* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-nmw: (49 commits)
[GFS2] fix assertion in log_refund()
[GFS2] fix GFP_KERNEL misuses
[GFS2] test for IS_ERR rather than 0
[GFS2] Invalidate cache at correct point
[GFS2] fs/gfs2/recovery.c: suppress warnings
[GFS2] Faster gfs2_bitfit algorithm
[GFS2] Streamline quota lock/check for no-quota case
[GFS2] Remove drop of module ref where not needed
[GFS2] gfs2_adjust_quota has broken unstuffing code
[GFS2] possible null pointer dereference fixup
[GFS2] Need to ensure that sector_t is 64bits for GFS2
[GFS2] re-support special inode
[GFS2] remove gfs2_dev_iops
[GFS2] fix file_system_type leak on gfs2meta mount
[GFS2] Allow bmap to allocate extents
[GFS2] Fix a page lock / glock deadlock
[GFS2] proper extern for gfs2/locking/dlm/mount.c:gdlm_ops
[GFS2] gfs2/ops_file.c should #include "ops_inode.h"
[GFS2] be*_add_cpu conversion
[GFS2] Fix bug where we called drop_bh incorrectly
...
[SCSI] iscsi: bidi support at the generic libiscsi level
- prepare the additional bidi_read rlength header.
- access the right scsi_in() and/or scsi_out() side of things.
also for resid.
- Handle BIDI underflow overflow from target
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com> Reviewed-by: Pete Wyckoff <pw@osc.edu> Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Martin Peschke [Fri, 18 Apr 2008 10:51:55 +0000 (12:51 +0200)]
[SCSI] zfcp: fix 31 bit compile warnings
drivers/s390/scsi/zfcp_aux.c: In function ‘zfcp_fsf_incoming_els_rscn’:
drivers/s390/scsi/zfcp_aux.c:1379: warning: cast from pointer to integer of
different size
drivers/s390/scsi/zfcp_aux.c: In function ‘zfcp_fsf_incoming_els_plogi’:
drivers/s390/scsi/zfcp_aux.c:1432: warning: cast from pointer to integer of
different size
drivers/s390/scsi/zfcp_aux.c: In function ‘zfcp_fsf_incoming_els_logo’:
drivers/s390/scsi/zfcp_aux.c:1457: warning: cast from pointer to integer of
different size
..
Just passing pointers rids us of these warnings and improves readability.
Signed-off-by: Martin Peschke <mp3@de.ibm.com> Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
FUJITA Tomonori [Mon, 31 Mar 2008 01:03:41 +0000 (10:03 +0900)]
[SCSI] bsg: remove minor in struct bsg_device
minor in struct bsg_device is used as identifier to find the
corresponding struct bsg_device_class. However, request_queuse can be
used as identifier for that and the minor in struct bsg_device is
unnecessary.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
FUJITA Tomonori [Mon, 31 Mar 2008 01:03:38 +0000 (10:03 +0900)]
[SCSI] bsg: takes a ref to struct device in fops->open
bsg_register_queue() takes a ref to struct device that a caller
passes. For example, bsg takes a ref to the sdev_gendev for scsi
devices. However, bsg doesn't inrease the refcount in fops->open. So
while an application opens a bsg device, the scsi device that the bsg
device holds can go away (bsg also takes a ref to a queue, but it
doesn't prevent the device from going away).
With this patch, bsg increases the refcount of struct device in
fops->open and decreases it in fops->release.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch exposes o2net information via debugfs. The information includes
the list of sockets (sock_containers) as well as the list of outstanding
messages (send_tracking). Useful for o2dlm debugging.
(This patch is derived from an earlier one written by Zach Brown that
exposed the same information via /proc.)
[Mark: checkpatch fixes]
Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com> Reviewed-by: Joel Becker <joel.becker@oracle.com> Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Mark Fasheh [Fri, 4 Apr 2008 19:45:55 +0000 (12:45 -0700)]
ocfs2: Only build ocfs2/dlm with the o2cb stack module
fs/ocfs2/dlm/ocfs2_dlm.ko and fs/ocfs2/dlm/ocfs2_dlmfs.ko get built if
CONFIG_FS_OCFS2 is specified. This isn't quite how it should happen any more
- the "o2cb" dlm modules should only be built if CONFIG_FS_OCFS2_O2CB is
set, so update the dlm Makefile accordingly.
Signed-off-by: Mark Fasheh <mfasheh@suse.com> Acked-by: Randy Dunlap <randy.dunlap@oracle.com> Acked-by: Joel Becker <joel.becker@oracle.com>
Jeff Mahoney [Fri, 28 Mar 2008 23:44:13 +0000 (16:44 -0700)]
ocfs2/cluster: Get rid of arguments to the timeout routines
We keep seeing bug reports related to NULL pointer derefs in
o2net_set_nn_state(). When I originally wrote up the configurable timeout
patch, I had tried to plan for multiple clusters. This was silly.
The timeout routines all use o2nm_single_cluster so there's no point in
passing an argument at all. This patch removes the arguments and kills those
bugs dead.
Signed-off-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Julia Lawall [Fri, 28 Mar 2008 21:43:10 +0000 (14:43 -0700)]
fs/ocfs2/aops.c: test for IS_ERR rather than 0
The function ocfs2_start_trans always returns either a valid pointer or a
value made with ERR_PTR, so its result should be tested with IS_ERR, not
with a test for 0.
Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Tao Ma [Wed, 5 Mar 2008 08:11:46 +0000 (16:11 +0800)]
ocfs2: Add inode stealing for ocfs2_reserve_new_inode
Inode allocation is modified to look in other nodes allocators during
extreme out of space situations. We retry our own slot when space is freed
back to the global bitmap, or whenever we've allocated more than 1024 inodes
from another slot.
Signed-off-by: Tao Ma <tao.ma@oracle.com> Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Tao Ma [Mon, 3 Mar 2008 09:12:30 +0000 (17:12 +0800)]
ocfs2: Add ac_alloc_slot in ocfs2_alloc_context
In inode stealing, we no longer restrict the allocation to
happen in the local node. So it is neccessary for us to add
a new member in ocfs2_alloc_context to indicate which slot
we are using for allocation. We also modify the process of
local alloc so that this member can be used there also.
Signed-off-by: Tao Ma <tao.ma@oracle.com> Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com> Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Tao Ma [Mon, 3 Mar 2008 09:12:09 +0000 (17:12 +0800)]
ocfs2: Add a new parameter for ocfs2_reserve_suballoc_bits
In some cases(Inode stealing from other nodes), we may not want
ocfs2_reserve_suballoc_bits to allocate new groups from the
global_bitmap since it may already be full. So add a new parameter
for this.
Signed-off-by: Tao Ma <tao.ma@oracle.com> Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com> Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Tao Ma [Wed, 30 Jan 2008 06:21:32 +0000 (14:21 +0800)]
ocfs2: Enable cross extent block merge.
In ocfs2_figure_merge_contig_type, we judge whether there exists
a cross extent block merge and enable it by setting CONTIG_LEFT
and CONTIG_RIGHT accordingly.
Signed-off-by: Tao Ma <tao.ma@oracle.com> Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Tao Ma [Wed, 30 Jan 2008 06:21:05 +0000 (14:21 +0800)]
ocfs2: Add support for cross extent block
In ocfs2_merge_rec_left, when we find the merge extent is "CONTIG_RIGHT"
with the first extent record of the next extent block, we will merge it to
the next extent block and change all the related extent blocks accordingly.
In ocfs2_merge_rec_right, when we find the merge extent is "CONTIG_LEFT"
with the last extent record of the previous extent block, we will merge
it to the prevoius extent block and change all the related extent blocks
accordingly.
As for CONTIG_LEFTRIGHT, we will handle CONTIG_RIGHT first so that when
the index is zero, the merge process will be more efficient and easier.
Signed-off-by: Tao Ma <tao.ma@oracle.com> Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Mark Fasheh [Wed, 30 Jan 2008 01:08:26 +0000 (17:08 -0800)]
ocfs2: Move /sys/o2cb to /sys/fs/o2cb
/sys/fs is where we really want file system specific sysfs objects.
Ocfs2-tools has been updated to look in /sys/fs/o2cb. We can maintain
backwards compatibility with old ocfs2-tools by using a sysfs symlink. After
some time (2 years), the symlink can be safely removed. This patch also adds
documentation to make it easier for people to figure out what /sys/fs/o2cb
is used for.
Mark Fasheh [Tue, 29 Jan 2008 22:35:18 +0000 (14:35 -0800)]
sysfs: Allow removal of symlinks in the sysfs root
Allow callers of sysfs_remove_link() to pass a NULL kobj, in which case
sysfs_root will be used as the parent directory. This allows us to tear down
top level symlinks created via sysfs_create_link(), which already has
similar handling of a NULL parent object.
Signed-off-by: Mark Fasheh <mfasheh@suse.com> Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Tao Ma [Wed, 5 Mar 2008 07:50:12 +0000 (15:50 +0800)]
ocfs2: Reconnect after idle time out.
Currently, o2net connects to a node on hb_up and disconnects on
hb_down and net timeout.
It disconnects on net timeout is ok, but it should attempt to
reconnect back. This is because sometimes nodes get overloaded
enough that the network connection breaks but the disk hb does not.
And if we get into that situation, we either fence (unnecessarily)
or wait for its disk hb to die (and sometimes hang in the process).
So in this updated scheme, when the network disconnects, we keep
attempting to reconnect till we succeed or we get a disk hb down
event.
If the other node is really dead, then we will eventually get a
node down event. If not, we should be able to connect again and
continue.
Signed-off-by: Tao Ma <tao.ma@oracle.com> Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Sunil Mushran [Fri, 14 Mar 2008 18:18:24 +0000 (11:18 -0700)]
ocfs2/dlm: Cleanup lockres print
A previous patch added KERN_NOTICE to printks printing the lockres that
cluttered the output. This patch removes the log level. For people concerned
with syslog clutter, please note we now use this facility to print lockres
only during an error.
Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com> Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Sunil Mushran [Mon, 10 Mar 2008 22:16:29 +0000 (15:16 -0700)]
ocfs2/dlm: Fix lockname in lockres print function
__dlm_print_one_lock_resource was printing lockname incorrectly.
Also, we now use printk directly instead of mlog as the latter prints
the line context which is not useful for this print.
Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com> Signed-off-by: Joel Becker <joel.becker@oracle.com> Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Sunil Mushran [Mon, 10 Mar 2008 22:16:25 +0000 (15:16 -0700)]
ocfs2/dlm: Move struct dlm_master_list_entry to dlmcommon.h
This patch moves some mle related definitions from dlmmaster.c
to dlmcommon.h. Future patches need these definitions to dump mle
debugging information.
Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com> Signed-off-by: Joel Becker <joel.beckeroracle.com> Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Sunil Mushran [Mon, 10 Mar 2008 22:16:21 +0000 (15:16 -0700)]
ocfs2/dlm: Link all lockres' to a tracking list
This patch links all the lockres' to a tracking list in dlm_ctxt.
We will use this in an upcoming patch that will walk the entire
list and to dump the lockres states to a debugfs file.
Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com> Signed-off-by: Joel Becker <joel.becker@oracle.com> Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Sunil Mushran [Mon, 10 Mar 2008 22:16:20 +0000 (15:16 -0700)]
ocfs2/dlm: Create slabcaches for lock and lockres
This patch makes the o2dlm allocate memory for lockres, lockname and lock
structures from slabcaches rather than kmalloc. This allows us to not only
make these allocs more efficient but also allows us to track the memory being
consumed by these structures.
Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com> Signed-off-by: Joel Becker <joel.becker@oracle.com> Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Joel Becker [Wed, 5 Mar 2008 01:58:56 +0000 (17:58 -0800)]
ocfs2: Allow selection of cluster plug-ins.
ocfs2 now supports plug-ins for the classic O2CB stack as well as
userspace cluster stacks in conjunction with fs/dlm. This allows zero,
one, or both of the plug-ins to be selected in Kconfig. For local mounts
(non-clustered), neither plug-in is needed. Both plugins can be loaded
at one time, the runtime will select the one needed for the cluster
systme in use.
Signed-off-by: Joel Becker <joel.becker@oracle.com> Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Joel Becker [Wed, 5 Mar 2008 00:09:39 +0000 (16:09 -0800)]
ocfs2: Change mlog_bug_on to BUG_ON in ocfs2_lockid.h
The masklog code is in the o2cb stack, but ocfs2_lockid.h now needs to
be included by the user stack. The BUG() in ocfs2_lock_type_string()
does not need masklog support, so change it to a regular BUG_ON().
Signed-off-by: Joel Becker <joel.becker@oracle.com> Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Joel Becker [Wed, 20 Feb 2008 23:39:44 +0000 (15:39 -0800)]
ocfs2: Add the 'set version' message to the ocfs2_control device.
The "SETV" message sets the filesystem locking protocol version as
negotiated by the client. The client negotiates based on the maximum
version advertised in /sys/fs/ocfs2/max_locking_protocol.
Signed-off-by: Joel Becker <joel.becker@oracle.com> Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Joel Becker [Wed, 20 Feb 2008 22:44:34 +0000 (14:44 -0800)]
ocfs2: Add the local node id to the handshake.
This is the second part of the ocfs2_control handshake. After
negotiating the ocfs2_control protocol, the daemon tells the filesystem
what the local node id is via the SETN message.
Signed-off-by: Joel Becker <joel.becker@oracle.com> Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Joel Becker [Tue, 19 Feb 2008 03:40:12 +0000 (19:40 -0800)]
ocfs2: Start the ocfs2_control handshake.
When a control daemon opens the ocfs2_control device, it must perform a
handshake to tell the filesystem it is something capable of monitoring
cluster status. Only after the handshake is complete will the filesystem
allow mounts.
This is the first part of the handshake. The daemon reads all supported
ocfs2_control protocols, then writes in the protocol it will use.
Signed-off-by: Joel Becker <joel.becker@oracle.com> Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Joel Becker [Fri, 1 Feb 2008 23:17:30 +0000 (15:17 -0800)]
ocfs2: Add the 'cluster_stack' sysfs file.
Userspace can now query and specify the cluster stack in use via the
/sys/fs/ocfs2/cluster_stack file. By default, it is 'o2cb', which is
the classic stack. Thus, old tools that do not know how to modify this
file will work just fine. The stack cannot be modified if there is a
live filesystem.
ocfs2_cluster_connect() now takes the expected cluster stack as an
argument. This way, the filesystem and the stack glue ensure they are
speaking to the same backend.
If the stack is 'o2cb', the o2cb stack plugin is used. For any other
value, the fsdlm stack plugin is selected.
Signed-off-by: Joel Becker <joel.becker@oracle.com> Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Joel Becker [Fri, 1 Feb 2008 23:08:23 +0000 (15:08 -0800)]
ocfs2: Add the USERSPACE_STACK incompat bit.
The filesystem gains the USERSPACE_STACK incomat bit and the
s_cluster_info field on the superblock. When a userspace stack is in
use, the name of the stack is stored on-disk for mount-time
verification.
The "cluster_stack" option is added to mount(2) processing. The mount
process needs to pass the matching stack name. If the passed name and
the on-disk name do not match, the mount is failed.
When using the classic o2cb stack, the incompat bit is *not* set and no
mount option is used other than the usual heartbeat=local. Thus, the
filesystem is compatible with older tools.
Signed-off-by: Joel Becker <joel.becker@oracle.com> Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Joel Becker [Fri, 1 Feb 2008 07:56:17 +0000 (23:56 -0800)]
ocfs2: Create stack glue sysfs files.
Introduce a set of sysfs files that describe the current stack glue
state. The files live under /sys/fs/ocfs2. The locking_protocol file
displays the version of ocfs2's locking code. The
loaded_cluster_plugins file displays all of the currently loaded stack
plugins. When filesystems are mounted, the active_cluster_plugin file
will display the plugin in use.
Signed-off-by: Joel Becker <joel.becker@oracle.com> Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Joel Becker [Fri, 1 Feb 2008 23:03:57 +0000 (15:03 -0800)]
ocfs2: Break out stackglue into modules.
We define the ocfs2_stack_plugin structure to represent a stack driver.
The o2cb stack code is split into stack_o2cb.c. This becomes the
ocfs2_stack_o2cb.ko module.
The stackglue generic functions are similarly split into the
ocfs2_stackglue.ko module. This module now provides an interface to
register drivers. The ocfs2_stack_o2cb driver registers itself. As
part of this interface, ocfs2_stackglue can load drivers on demand.
This is accomplished in ocfs2_cluster_connect().
ocfs2_cluster_disconnect() is now notified when a _hangup() is pending.
If a hangup is pending, it will not release the driver module and will
let _hangup() do that.
Signed-off-by: Joel Becker <joel.becker@oracle.com>
Joel Becker [Fri, 1 Feb 2008 23:02:36 +0000 (15:02 -0800)]
ocfs2: Create ocfs2_stack_operations and split out the o2cb stack.
Define the ocfs2_stack_operations structure. Build o2cb_stack_ops from
all of the o2cb-specific stack functions. Change the generic stack glue
functions to call the stack_ops instead of the o2cb functions directly.
The o2cb functions are moved to stack_o2cb.c. The headers are cleaned up
to where only needed headers are included.
In this code, stackglue.c and stack_o2cb.c refer to some shared
extern variables. When they become modules, that will change.
Signed-off-by: Joel Becker <joel.becker@oracle.com> Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Joel Becker [Fri, 1 Feb 2008 22:51:03 +0000 (14:51 -0800)]
ocfs2: Split o2cb code from generic stack functions.
Split off the o2cb-specific funtionality from the generic stack glue
calls. This is a precurser to wrapping the o2cb functionality in an
operations vector.
Signed-off-by: Joel Becker <joel.becker@oracle.com> Signed-off-by: Mark Fasheh <mfasheh@suse.com>
projects / linux-2.6 / log