Merge branch 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] vmlogrdr function annotation.
[S390] s390: rename CPU_IDLE to S390_CPU_IDLE
[S390] cio: Remove prototype for non-existing function cmf_reset().
[S390] zcrypt: fix request timeout handling
[S390] system call optimization.
[S390] dasd: Avoid compile warnings on !CONFIG_DASD_PROFILE
[S390] Remove volatile from atomic_t
[S390] Program check in diag 210 under 31 bit
[S390] Bogomips calculation for 64 bit.
[S390] smp: Merge smp_count_cpus() and smp_get_save_areas().
[S390] zcore: Fix __user annotation.
[S390] fixed cdl-format detection.
[S390] sclp: Test facility list before executing a service call.
[S390] sclp: introduce some new interfaces.
[S390] Fixed comment typo.
[S390] vmcp cleanup
Merge branch 'splice-2.6.23' of git://git.kernel.dk/data/git/linux-2.6-block
* 'splice-2.6.23' of git://git.kernel.dk/data/git/linux-2.6-block:
pipe: add documentation and comments
pipe: change the ->pin() operation to ->confirm()
Remove remnants of sendfile()
xip sendfile removal
splice: completely document external interface with kerneldoc
sendfile: remove bad_sendfile() from bad_file_ops
shmem: convert to using splice instead of sendfile()
relay: use splice_to_pipe() instead of open-coding the pipe loop
pipe: allow passing around of ops private pointer
splice: divorce the splice structure/function definitions from the pipe header
splice: relay support
sendfile: convert nfsd to splice_direct_to_actor()
sendfile: convert nfs to using splice_read()
loop: convert to using splice_direct_to_actor() instead of sendfile()
splice: add void cookie to the actor data
sendfile: kill generic_file_sendfile()
sendfile: remove .sendfile from filesystems that use generic_file_sendfile()
sys_sendfile: switch to using ->splice_read, if available
vmsplice: add vmsplice-to-user support
splice: abstract out actor data
Merge branch 'trivial-2.6.23' of git://git.kernel.dk/data/git/linux-2.6-block
* 'trivial-2.6.23' of git://git.kernel.dk/data/git/linux-2.6-block:
Documentation/block/barrier.txt is not in sync with the actual code: - blk_queue_ordered() no longer has a gfp_mask parameter - blk_queue_ordered_locked() no longer exists - sd_prepare_flush() looks slightly different
Use list_for_each_entry() instead of list_for_each() in the block device
Make a "menuconfig" out of the Kconfig objects "menu, ..., endmenu",
block/Kconfig already has its own "menuconfig" so remove these
Use menuconfigs instead of menus, so the whole menu can be disabled at once
cfq-iosched: fix async queue behaviour
unexport bio_{,un}map_user
Remove legacy CDROM drivers
[PATCH] fix request->cmd == INT cases
cciss: add new controller support for P700m
[PATCH] Remove acsi.c
[BLOCK] drop unnecessary bvec rewinding from flush_dry_bio_endio
[PATCH] cdrom_sysctl_info fix
blk_hw_contig_segment(): bad segment size checks
[TRIVIAL PATCH] Kill blk_congestion_wait() stub for !CONFIG_BLOCK
Robert P. J. Day [Tue, 10 Jul 2007 10:37:56 +0000 (06:37 -0400)]
[MIPS] PNX8550: Cleanup proc code.
Here's a slightly cleaner way of creating the /proc structure for the
pnx8850. mostly, it creates a directory with default mode 555, since the
one you're creating is mode 444, which is somewhat unusual for a directory
under /proc.
[MIPS] Change names of local variables to silence sparse
This patch is an workaround for these sparse warnings:
linux/include/linux/calc64.h:25:17: warning: symbol '__quot' shadows an earlier one
linux/include/linux/calc64.h:25:17: originally declared here
linux/include/linux/calc64.h:25:17: warning: symbol '__mod' shadows an earlier one
linux/include/linux/calc64.h:25:17: originally declared here
[MIPS] Add debugfs files to show fpuemu statistics
Export contents of struct mips_fpu_emulator_stats via debugfs.
There is no way to read these statistics for now but they (at least
the "emulated" count) might be sometimes useful for performance tuning
on FPU-less CPUs.
[MIPS] rbtx4938: Fix secondary PCIC and glue internal NICs
* Fix pci ops for secondary PCIC
* Do not reserve 1MB for PCI MEM region (leave PCIBIOS_MIN_MEM zero)
* Use platform_device to provide ethernet addresses for internal NICs.
(background: TX49XX SoCs include PCI NIC (TC35815 compatible)
connected via its internal PCI bus, but the NIC's PROM interface is
not connected to SEEPROM. So we must provide its ethernet address
by another way.)
* Check return value of early_read_config_word()
Atsushi Nemoto [Fri, 29 Jun 2007 13:34:53 +0000 (22:34 +0900)]
[MIPS] tc35815: Load MAC address via platform_device
TX49XX SoCs include PCI NIC (TC35815 compatible) connected via its
internal PCI bus, but the NIC's PROM interface is not connected to
SEEPROM. So we must provide its ethernet address by another way.
Atsushi Nemoto [Mon, 25 Jun 2007 16:14:01 +0000 (01:14 +0900)]
[MIPS] Make ioremap() work on TX39/49 special unmapped segment
TX39XX and TX49XX have "reserved" segment in CKSEG3 area.
0xff000000-0xff3fffff on TX49XX and 0xff000000-0xfffeffff on TX39XX
are reserved (unmapped, uncached). Controllers on these SoCs are
placed in this segment.
This patch add plat_ioremap() and plat_iounmap() to override default
behavior and implement these hooks for TX39/TX49.
- use RTC_CLASS instead of GEN_RTC
- get rid of ds1216 in favour of a RTC_CLASS driver
- use correct console device for older RM400
- use physical addresses for 82596 device
- use 128 byte L1 cache line size (this is needed because most of the
SNI caches are using 128 L2 cache lines)
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
[MIPS] Enable support for the userlocal hardware register
Which will cut down the cost of RDHWR $29 which is used to obtain the
TLS pointer and so far being emulated in software down to a single cycle
operation.
This is an optimised implementation of early printk() for the DECstation.
After the recent conversion to a MIPS-specific generic routine using a
character-by-character output the performance dropped significantly.
This change reverts to the previous speed -- even at 9600 bps of the
serial console the difference is visible with a naked eye; I presume for a
framebuffer it is even worse (it may depend on exactly which one is used
though).
Additionally the change includes a fix for a problem that the old
implementation had -- the format used would not actually limit the length
of the string output. This new implementation uses a local buffer to deal
with it -- even with this additional copying it is much faster than the
generic function.
Plus this driver is registered much earlier than the generic one,
allowing one to see critical messages, such as one about an incorrect CPU
setting used, that are produced beforehand. :-)
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Franck Bui-Huu [Mon, 4 Jun 2007 15:46:35 +0000 (17:46 +0200)]
[MIPS] Fix PHYS_OFFSET for 64-bits kernels with 32-bits symbols
The current implementation of __pa() for 64-bits kernels with 32-bits
symbols is broken. In this configuration, we need 2 values for
PAGE_OFFSET, one in XKPHYS and the other in CKSEG0 space.
When the value in CKSEG0 space is used, it doesn't take into account
of PHYS_OFFSET. Even worse we can't redefine this value.
The patch restores CPHYSADDR() but in __pa()'s implementation because
it removes the need of 2 PAGE_OFFSET.
OTOH, CPHYSADDR() is quite bad when dealing with mapped kernels. So
this patch assumes there's no need to deal with such kernel in 64-bits
world.
Franck Bui-Huu [Mon, 4 Jun 2007 15:46:33 +0000 (17:46 +0200)]
[MIPS] Make PAGE_OFFSET aware of PHYS_OFFSET
For platforms that use PHYS_OFFSET and do not use a mapped kernel,
this patch automatically adds PHYS_OFFSET into PAGE_OFFSET.
Therefore there are no more needs for them to redefine PAGE_OFFSET.
For mapped kernel, they need to redefine PAGE_OFFSET anyways.
No point in adding yet another #ifdef for Loongson since all this mask is
being used for is converting an XKPHYS address into a physical address
anyway. So replace all definitions by one with the highest architectural
possible value.
Florian Fainelli [Tue, 22 May 2007 19:44:42 +0000 (21:44 +0200)]
[MIPS] Add generic GPIO to Au1x00
This patch adds support for the generic GPIO API to Au1x00 boards. It requires
the generic GPIO patch for MIPS boards by Yoichi Yuasa. Now there is a MIPS
target using it, can you queue these patchset for 2.6.22 ? Thank you very
much in advance.
Atsushi Nemoto [Tue, 29 May 2007 15:38:07 +0000 (00:38 +0900)]
[MIPS] Simplify missing-syscalls for N32 and O32
Use standard missing-syscalls with EXTRA_CFLAGS instead of duplicating
the command. And move the archprepare rule before the archclean rule.
Suggested by Franck Bui-Huu. Also add "echo" to show the target ABI.
Documentation/block/barrier.txt is not in sync with the actual code: - blk_queue_ordered() no longer has a gfp_mask parameter - blk_queue_ordered_locked() no longer exists - sd_prepare_flush() looks slightly different
With the cfq_queue hash removal, we inadvertently got rid of the
async queue sharing. This was not intentional, in fact CFQ purposely
shares the async queue per priority level to get good merging for
async writes.
So put some logic in cfq_get_queue() to track the shared queues.
On Tue, 2007-07-10 at 10:06 +0100, Christoph Hellwig wrote:
> > -#define GFS2_LARGE_FH_SIZE 10
> > -
> > -struct gfs2_fh_obj {
> > - struct gfs2_inum_host this;
> > - u32 imode;
> > -};
> > +#define GFS2_LARGE_FH_SIZE 8
>
> Because gfs2_decode_fh only accepts file handles with GFS2_LARGE_FH_SIZE
> or GFS2_LARGE_FH_SIZE you don't accept filehandles sent out by and older
> gfs version anymore. Stale filehandles because of a new kernel version
> are a big no-no, so please add back code to handle the old filehandles
> on the decode side.
>
This should fix that problem I think since its only relating to end of
the fh we can just ignore that field in order to accept the older
format.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Wendy Cheng <wcheng@redhat.com>
Anton Vorontsov [Thu, 3 May 2007 20:45:39 +0000 (00:45 +0400)]
[BATTERY] 1-Wire ds2760 chip battery driver
This is driver for batteries with ds2760 chip inside, found inside
almost every HP iPaq and HTC PDAs/phones.
Signed-off-by: Anton Vorontsov <cbou@mail.ru> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Anton Vorontsov [Thu, 3 May 2007 20:32:17 +0000 (00:32 +0400)]
[BATTERY] pda_power platform driver
Common power driver for PDAs and phones with one or two external
power supplies (AC/USB) connected to main and backup batteries,
and optional builtin charger.
It's used to stop logic duplication through different embedded
devices. So, power supply *logic* is here. pda_power register
power supplies, and will take care about notifying batteries
about power changes through external power interface.
Currently, power consumption legal limits (including USB power
consumption) should be handled by platform code, inside set_charge
function.
Signed-off-by: Anton Vorontsov <cbou@mail.ru> Signed-off-by: Roman Moravcik <roman.moravcik@gmail.com> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Anton Vorontsov <cbou@mail.ru> Signed-off-by: David Woodhouse <dwmw2@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Use __init and __exit for vmlogrdr. Both functions are only referenced
by the module_init exit macros, so this change should be fine.
Acked-by: Stefan Weinhuber <wein@de.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
sched-cfs-v2.6.22-git-v18.patch introduces CPU_IDLE in sched.h.
This conflict with the already existing define in
include/asm-s390/processor.h
Just rename the s390 defines, since they will go away as soon as
we support CONFIG_NO_HZ instead of our own CONFIG_NO_IDLE_HZ.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Ralph Wuerthner [Tue, 10 Jul 2007 09:24:19 +0000 (11:24 +0200)]
[S390] zcrypt: fix request timeout handling
Under very high load zcrypt requests may timeout while waiting on the
request queue. Modify zcrypt that timeouts are based on crypto adapter
responses. A timeout occurs only if a crypto adapter does not respond
within a given time frame to sumitted requests.
Signed-off-by: Ralph Wuerthner <rwuerthn@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
After the in-kernel system call has been remove the system call path
can be optimized. The problem state bit of the old psw is always set
between system_call and sysc_do_svc. SAVE_ALL_SVC uses this information
to avoid two instructions.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
[S390] dasd: Avoid compile warnings on !CONFIG_DASD_PROFILE
drivers/s390/block/dasd_proc.c:33:
warning: 'dasd_get_user_string' defined but not used
drivers/s390/block/dasd_proc.c:172:
warning: 'dasd_statistics_array' defined but not used
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Michael Holzheu [Tue, 10 Jul 2007 09:24:15 +0000 (11:24 +0200)]
[S390] Program check in diag 210 under 31 bit
If a virtual address is passed to the diag210 function under 31 bit, we get a
programming exception, since diag 210 only works with physical addresses. To
fix this, the content of the diag210 data structure is copied to a local
structure and the physical address of that structure is passed to diagnose 210.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The bogomips calculation triggered via reading from /proc/cpuinfo
can return incorrect values if the qrnnd assembly is called with a
pointer in %r2 with any of the upper 32 bits set.
Fix this by using 64 bit division / remainder operation provided by
gcc instead of calling the assembly.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Jens Axboe [Thu, 14 Jun 2007 11:10:48 +0000 (13:10 +0200)]
pipe: change the ->pin() operation to ->confirm()
The name 'pin' was badly chosen, it doesn't pin a pipe buffer
in the most commonly used sense in the kernel. So change the
name to 'confirm', after debating this issue with Hugh
Dickins a bit.
A good return from ->confirm() means that the buffer is really
there, and that the contents are good.
projects / linux-2.6 / log