This corrects an error in the computation of the open loss interval I_0:
* the interval length is (highest_seqno - start_seqno) + 1
* and not (highest_seqno - start_seqno).
This condition was not fully clear in RFC 3448, but reflects the current
revision state of rfc3448bis and is also consistent with RFC 4340, 6.1.1.
Further changes:
----------------
* variable renamed due to line length constraints;
* explicit typecast to `s64' to avoid implicit signed/unsigned casting.
This fixes a bug in the logic of the TFRC loss detection:
* new_loss_indicated() should not be called while a loss is pending;
* but the code allows this;
* thus, for two subsequent gaps in the sequence space, when loss_count
has not yet reached NDUPACK=3, the loss_count is falsely reduced to 1.
To avoid further and similar problems, all loss handling and loss detection is
now done inside tfrc_rx_hist_handle_loss(), using an appropriate routine to
track new losses.
Further changes:
----------------
* added a reminder that no RX history operations should be performed when
rx_handle_loss() has identified a (new) loss, since the function takes
care of packet reordering during loss detection;
* made tfrc_rx_hist_loss_pending() bool (thanks to an earlier suggestion
by Arnaldo);
* removed unused functions.
RFC 4340, 7.7 specifies up to 6 bytes for the NDP Count option, whereas the code
is currently limited to up to 3 bytes. This seems to be a relict of an earlier
draft version and is brought up to date by the patch.
The TFRC loss detection code used the wrong loss condition (RFC 4340, 7.7.1):
* the difference between sequence numbers s1 and s2 instead of
* the number of packets missing between s1 and s2 (one less than the distance).
Since this condition appears in many places of the code, it has been put into a
separate function, dccp_loss_free().
Further changes:
----------------
* tidied up incorrect typing (it was using `int' for u64/s64 types);
* optimised conditional statements for common case of non-reordered packets;
* rewrote comments/documentation to match the changes.
Max Krasnyansky [Thu, 10 Jul 2008 23:59:11 +0000 (16:59 -0700)]
tun: Persistent devices can get stuck in xoff state
The scenario goes like this. App stops reading from tun/tap.
TX queue gets full and driver does netif_stop_queue().
App closes fd and TX queue gets flushed as part of the cleanup.
Next time the app opens tun/tap and starts reading from it but
the xoff state is not cleared. We're stuck.
Normally xoff state is cleared when netdev is brought up. But
in the case of persistent devices this happens only during
initial setup.
The fix is trivial. If device is already up when an app opens
it we clear xoff state and that gets things moving again.
Signed-off-by: Max Krasnyansky <maxk@qualcomm.com> Tested-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
xfrm: Add a XFRM_STATE_AF_UNSPEC flag to xfrm_usersa_info
Add a XFRM_STATE_AF_UNSPEC flag to handle the AF_UNSPEC behavior for
the selector family. Userspace applications can set this flag to leave
the selector family of the xfrm_state unspecified. This can be used
to to handle inter family tunnels if the selector is not set from
userspace.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Thu, 10 Jul 2008 23:52:52 +0000 (16:52 -0700)]
ipv4: fib_trie: Fix lookup error return
In commit a07f5f508a4d9728c8e57d7f66294bf5b254ff7f "[IPV4] fib_trie: style
cleanup", the changes to check_leaf() and fn_trie_lookup() were wrong - where
fn_trie_lookup() would previously return a negative error value from
check_leaf(), it now returns 0.
Now fn_trie_lookup() doesn't appear to care about plen, so we can revert
check_leaf() to returning the error value.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Tested-by: William Boughton <bill@boughton.de> Acked-by: Stephen Heminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Take out the confusing language in tcp_frto, and organize the
undocumented values.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Acked-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: David S. Miller <davem@davemloft.net>
David Howells [Wed, 9 Jul 2008 22:06:45 +0000 (15:06 -0700)]
netfilter: nf_nat_snmp_basic: fix a range check in NAT for SNMP
Fix a range check in netfilter IP NAT for SNMP to always use a big enough size
variable that the compiler won't moan about comparing it to ULONG_MAX/8 on a
64-bit platform.
Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Wed, 9 Jul 2008 22:06:12 +0000 (15:06 -0700)]
netfilter: nf_conntrack_tcp: fix endless loop
When a conntrack entry is destroyed in process context and destruction
is interrupted by packet processing and the packet is an attempt to
reopen a closed connection, TCP conntrack tries to kill the old entry
itself and returns NF_REPEAT to pass the packet through the hook
again. This may lead to an endless loop: TCP conntrack repeatedly
finds the old entry, but can not kill it itself since destruction
is already in progress, but destruction in process context can not
complete since TCP conntrack is keeping the CPU busy.
Drop the packet in TCP conntrack if we can't kill the connection
ourselves to avoid this.
Reported by: hemao77@gmail.com [ Kernel bugzilla #11058 ] Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
If a mesh or ad-hoc interface is brought up and later it is replaced
by managed interface, the managed interface will keep transmitting
the beacons that were configured for the former interface. This patch
fixes that behaviour.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Tue, 8 Jul 2008 11:45:20 +0000 (13:45 +0200)]
rt2x00: Disable synchronization during initialization
As soon as init_registers() was called, the rt2400/rt2500
would start raising beacondone interrupts. Since this is highly
premature since no beacons were provided yet, we should
initialize the synchronization register to 0.
This will make all drivers initialize it to 0 regardless
if they are raising beacondone interrupts or not, since it only
makes sense to have it completely disabled.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes the fast_start parameter from the rc_pid parameters
information and instead uses the parameter macro when initializing
the rc_pid state. Since the parameter is only used on initialization,
there is no point of making exporting it via debugfs. This also fixes
uninitialized memory references to the fast_start and norm_offset
parameters detected by the kmemcheck utility. Thanks to Vegard Nossum
for reporting the bug.
Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
David S. Miller [Wed, 9 Jul 2008 05:49:00 +0000 (22:49 -0700)]
netdev: Kill qdisc_ingress, use netdev->rx_queue.qdisc instead.
Now that our qdisc management is bi-directional, per-queue, and fully
orthogonal, there is no reason to have a special ingress qdisc pointer
in struct net_device.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 9 Jul 2008 00:33:13 +0000 (17:33 -0700)]
netdev: The ingress_lock member is no longer needed.
Every qdisc is assosciated with a queue, and in the case of ingress
qdiscs that will now be netdev->rx_queue so using that queue's lock is
the thing to do.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 9 Jul 2008 00:18:23 +0000 (17:18 -0700)]
netdev: Move queue_lock into struct netdev_queue.
The lock is now an attribute of the device queue.
One thing to notice is that "suspicious" places
emerge which will need specific training about
multiple queue handling. They are so marked with
explicit "netdev->rx_queue" and "netdev->tx_queue"
references.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Acked-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Tue, 8 Jul 2008 22:36:57 +0000 (15:36 -0700)]
vlan: avoid header copying and linearisation where possible
- vlan_dev_reorder_header() is only called on the receive path after
calling skb_share_check(). This means we can use skb_cow() since
all we need is a writable header.
- vlan_dev_hard_header() includes a work-around for some apparently
broken out of tree MPLS code. The hard_header functions can expect
to always have a headroom of at least there own hard_header_len
available, so the reallocation check is unnecessary.
- __vlan_put_tag() can use skb_cow_head() to avoid the skb_unshare()
copy when the header is writable.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
After this we have an ifp->rt inserted into fib6 lists, but
queued for gc, which in turn can result in oopses in the
fib6_run_gc. Maybe some other nasty things, but we caught
only the oops in gc so far.
The solution is to disarm the ifp->timer before flushing the
rt from it.
Signed-off-by: Andrey Vagin <avagin@parallels.com> Signed-off-by: Pavel Emelyanov <xemul@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Although I only tested similar code (I don't use any of this wireless
code), the state maintainance between Netlink dump callback invocations
seems wrong here and should lead to an endless loop. There are also other
examples in the same file which might have the same problem. Perhaps someone
can actually test this (or refute my logic).
Take the simple example with only one element in the list (which should fit
into the message):
Larry Finger [Tue, 8 Jul 2008 14:43:43 +0000 (09:43 -0500)]
rtl8187: Change detection of RTL8187B with USB ID of 8187
Some early versions of RTL8187B devices have a USB ID of 0x8187
rather than the 0x8189 of later models. In addition, it appears
that these early units also must be programmed with lower power.
Previous patches used the Product ID string to detect this situation,
but did not address the low power question. This patch uses the
hardware version and sets the power accordingly.
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br> Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net> Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
rtl8187: change rtl8187_dev.c to support RTL8187B (part 2)
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br> Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net> Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
rtl8187: change rtl8187_dev.c to support RTL8187B (part 1)
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br> Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net> Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
rtl8187: updating rtl8187_rtl8225.c to support RTL8187B
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br> Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net> Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br> Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net> Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br> Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net> Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Fri, 4 Jul 2008 13:39:01 +0000 (08:39 -0500)]
b43legacy: Remove switch statement with 64-bit index
The gcc 3.4 fork used to compile the MN10300 port emits unwanted
__ucmpdi2() calls for switch statements that use a 64bit value.
This patch removes such a switch from b43legacy, and makes the code
more like that used in b43. Thanks to Adrian Bunk <bunk@kernel.org>
for reporting the problem.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Fri, 4 Jul 2008 14:14:59 +0000 (16:14 +0200)]
rt2x00: Report RX end time for rt2400pci
rt2400 is the only currently available rt2x00 driver which
supports reporting of the RX end time for frames.
Since mac80211 uses this information for IBSS syncing, it
is important that it is being reported.
v2: Complement 32 bits of RX timestamp with upper 32bits from TSF
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Fri, 4 Jul 2008 11:41:31 +0000 (13:41 +0200)]
rt2x00: Use ieee80211_hw->workqueue again
Remove the rt2x00 singlethreaded workqueue and move
the link tuner and packet filter scheduled work to
the ieee80211_hw->workqueue again.
The only exception is the interface scheduled work
handler which uses the mac80211 interface iterator
under the RTNL lock. This work needs to be handled
on the kernel workqueue to prevent lockdep issues.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Fri, 4 Jul 2008 12:56:07 +0000 (14:56 +0200)]
rt2x00: Decrease alignment headroom
We only need 4 bytes of headroom for alignment
purposes in the RX frame. It was previously higher
for optimization purposes which are no longer
possible due to DMA mappings.
v2: Fix patch error
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Fri, 4 Jul 2008 12:51:39 +0000 (14:51 +0200)]
rt2x00: Remove input_polldev requirements for rfkill
With the new rfkill interface there is no longer a need
for the input_polldev. Create a delayed_work structure
which we can put on the mac80211 workqueue and poll the
hardware every 1000ms.
v2: Decrease poll frequency from 100ms to 1000ms
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
rfkill: ignore errors from rfkill_toggle_radio in rfkill_add_switch
rfkill_add_switch() calls rfkill_toggle_radio() to set the state of a
recently registered rfkill class to the current global state [for that
rfkill->type].
The rfkill_toggle_radio() call is going to error out if the hardware is
RFKILL_STATE_HARD_BLOCKED, and the global state is RFKILL_STATE_UNBLOCKED.
That is a quite normal situation which I missed to account for. As things
stand, the error return from rfkill_toggle_radio ends up causing
rfkill_register to bail out with an error (de-registering the new switch in
the process), which is Not Nice.
Change rfkill_add_switch() to not return errors because of a failed call to
rfkill_toggle_radio(). We can go back to returning errors again (if that's
indeed the right thing to do) if we define the exact error codes the
rfkill->toggle_radio callbacks are to return in each situation, so that we
can ignore the right ones only.
Bug reported by "kionez <kionez@anche.no>".
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Cc: kionez <kionez@anche.no> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
rfkill: some minor kernel-doc changes for rfkill_toggle_radio
Improve rfkill_toggle_radio's kernel-doc header a bit.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211: add support for iwconfig wlanX frag auto
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Wed, 2 Jul 2008 22:27:13 +0000 (01:27 +0300)]
mac80211: call bss_info_change only once upon disassociation
This patch removes call of ieee80211_bss_info_change_notify from within
ieee80211_reset_erp_info. This allows gathering all bss info changes
into one call to the driver in the disassociation flow.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Harvey Harrison [Wed, 2 Jul 2008 18:05:34 +0000 (11:05 -0700)]
mac80211: move QOS control helpers into ieee80211.h
Also remove the WLAN_IS_QOS_DATA inline after removing the last
two users. This starts moving away from using rx->fc to using
the header frame_control directly.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211: remove MAC80211_DEBUG from net/mac80211/Kconfig.
This patch removes MAC80211_DEBUG from /net/mac80211/Kconfig
(in MAC80211_DEBUG_COUNTERS config entry), and replaces
MAC80211_DEBUG_MENU instead of MAC80211_DEBUG
(in MAC80211_VERBOSE_SPECT_MGMT_DEBUG config entry).
Signed-off-by: Rami Rosen <ramirose@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the iwlwifi rfkill. It removes the input device from iwl3945,
adds support for RFKILL_STATE_HARD_BLOCKED and calls rfkill_force_state() to
update the state rather than accessing it directly.
The calls to iwl|iwl3945_rfkill_set_hw_state() had to be moved because
rfkill_force_state() cannot be called from an atomic context.
Tested on iwl3945 and seems to work fine.
Cc: Randy Dunlap <randy.dunlap@oracle.com> Cc: Ivo van Doorn <ivdoorn@gmail.com> Cc: Fabien Crespel <fcrespel@gmail.com> Cc: Zhu Yi <yi.zhu@intel.com> Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Signed-off-by: Adel Gadllah <adel.gadllah@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Tue, 1 Jul 2008 07:44:50 +0000 (10:44 +0300)]
mac80211: fix warning: unused variable ifsta
This patch fixes warning unused variable ifsta
when compiling without CONFIG_MAC80211_VERBOSE_DEBUG
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ron Rindjunsky [Tue, 1 Jul 2008 07:44:51 +0000 (10:44 +0300)]
iwlwifi: request Tx of block ack request if necessary
This patch sets the block ack request flag if needed
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Tue, 1 Jul 2008 11:29:20 +0000 (14:29 +0300)]
mac80211: remove useless tid assignment for management and control frames
This patch removes useless tid assignment for management and control frames
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ron Rindjunsky [Tue, 1 Jul 2008 11:16:03 +0000 (14:16 +0300)]
mac80211: add block ack request capability
This patch adds block ack request capability
Signed-off-by: Ester Kummer <ester.kummer@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Tue, 1 Jul 2008 08:45:13 +0000 (10:45 +0200)]
mac80211: Don't request encryption for probe response
Probe responses shouldn't be encrypted, and mac80211 doesn't
set the crypto key accordingly. However it didn't set the
IEEE80211_TX_CTL_DO_NOT_ENCRYPT flag which means drivers
could make an attempt to encrypt it, and causing a NULL
pointer dereference when accessing the provided hw_key field.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patrick McHardy [Tue, 8 Jul 2008 10:24:44 +0000 (03:24 -0700)]
vlan: TCI related type and naming cleanups
The VLAN code contains multiple spots that use tag, id and tci as
identifiers for arguments and variables incorrectly and they actually
contain or are expected to contain something different. Additionally
types are used inconsistently (unsigned short vs u16) and identifiers
are sometimes capitalized.
- consistently use u16 for storing TCI, ID or QoS values
- consistently use vlan_id and vlan_tci for storing the respective values
- remove capitalization
- add kdoc comment to netif_hwaccel_{rx,receive_skb}
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Tue, 8 Jul 2008 10:23:57 +0000 (03:23 -0700)]
vlan: move struct vlan_dev_info to private header
Hide struct vlan_dev_info from drivers to prevent them from growing
more creative ways to use it. Provide accessors for the two drivers
that currently use it.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Tue, 8 Jul 2008 10:23:36 +0000 (03:23 -0700)]
vlan: uninline __vlan_hwaccel_rx
The function is huge and included at least once in every VLAN acceleration
capable driver. Uninline it; to avoid having drivers depend on the VLAN
module, the function is always built in statically when VLAN is enabled.
With all VLAN acceleration capable drivers that build on x86_64 enabled,
this results in:
text data bss dec hex filename 6515227 854044 343968 7713239 75b1d7 vmlinux.inlined 6505637 854044 343968 7703649 758c61 vmlinux.uninlined
----------------------------------------------------------
-9590
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Joonwoo Park [Tue, 8 Jul 2008 10:22:16 +0000 (03:22 -0700)]
vlan: Use is_vlan_dev()
Use simplified is_vlan_dev function.
Signed-off-by: Joonwoo Park <joonwpark81@gmail.com> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Tue, 8 Jul 2008 10:21:27 +0000 (03:21 -0700)]
vlan: fix network_header/mac_header adjustments
Lennert Buytenhek points out that the VLAN code incorrectly adjusts
skb->network_header to point in the middle of the VLAN header and
additionally tries to adjust skb->mac_header without checking for
validity.
The network_header should not be touched at all since we're only
adding headers in front of it, mac_header adjustments are not
necessary at all.
Based on patch by Lennert Buytenhek <buytenh@wantstofly.org>.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Some IRDA headers contain references to 'struct pm_dev' that are not
necessary any more and may be removed.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Pavel Machek <pavel@suse.cz> Signed-off-by: Samuel Ortiz <samuel@sortiz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Julius Volz [Tue, 8 Jul 2008 10:07:43 +0000 (03:07 -0700)]
irda: Fix netlink error path return value
Fix an incorrect return value check of genlmsg_put() in irda_nl_get_mode().
genlmsg_put() does not use ERR_PTR() to encode return values, it just
returns NULL on error.
Signed-off-by: Julius Volz <juliusv@google.com> Signed-off-by: Samuel Ortiz <samuel@sortiz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Ville Syrjala [Tue, 8 Jul 2008 10:07:16 +0000 (03:07 -0700)]
irda: New device ID for nsc-ircc
HP OmniBook 500's DSDT code changes the HID of the FIR device from
NSC6001 to HWPC224 when run under an "NT" operating system. Add the
new ID to the pnp device id table.
Signed-off-by: Ville Syrjala <syrjala@sci.fi> Signed-off-by: Samuel Ortiz <samuel@sortiz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Chen [Tue, 8 Jul 2008 10:06:46 +0000 (03:06 -0700)]
irda: via-ircc proper dma freeing
1. dma should be freed when dma2 request fail.
2. dma2 should be freed too when device close.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com> Signed-off-by: Samuel Ortiz <samuel@sortiz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-2.6 / log