[Bluetooth] Add ignore parameters to the HCI USB driver
This patch adds the module parameters ignore_csr and ignore_sniffer
to the HCI USB driver. This allows an easier use of CSR ROM chips
that need an additional initialization routine and the Frontline
sniffers.
Pete Zaitcev [Thu, 1 Sep 2005 21:35:05 +0000 (14:35 -0700)]
[PATCH] USB: Usbmon setup DMA patch
Alan Stern sent me this patch. It goes on top of the patch the adds
mon_dmapeek:
http://ftp.kernel.org/pub/linux/kernel/people/gregkh/gregkh-2.6/gregkh-04-usb/usb-usbmon-dma-areas.patch
Please be warned about ordering requirements or the build may fail.
Actually, mon_dmapeek is generic enough to support SETUP packets too.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com> Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Thomas Sailer [Fri, 9 Sep 2005 08:43:50 +0000 (10:43 +0200)]
[PATCH] usb: fix uss720 schedule with interrupts off
This patch fixes the long standing schedule with interrupts off problem
of the uss720 driver. The problem is caused by the parport layer calling
the save and restore methods within a write_lock_irqsave guarded region.
The fix is to issue the control transaction requests required by save
and restore asynchronously.
Signed-off-by: Thomas Sailer, <sailer@ife.ee.ethz.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Harald Welte [Sat, 3 Sep 2005 09:27:08 +0000 (11:27 +0200)]
[PATCH] USB: fix usbdevice_fs header breakage
[USBDEVFS] fix inclusion of <linux/compat.h> to avoud header mess
Without moving the include of compat.h down, userspace programs that use
usbdevice_fs.h end up including half the kernel includes (and eventually
fail to compile).
Signed-off-by: Harald Welte <laforge@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Daniel Drake [Wed, 31 Aug 2005 15:38:41 +0000 (16:38 +0100)]
[PATCH] USB: usb-storage: Add unusual_devs entry for Neuros Audio MP3 player
Alan Stern wrote:
> If the device sometimes reports the correct values, then you should
> include NEED_OVERRIDE flag to prevent messages about unnecessary
> overrides showing up in the system log. Also, if bInterfaceSubclass
> is correct and only bInterfaceProtocol is wrong, then the entry should
> say US_SC_DEVICE instead of US_SC_SCSI.
Fair points, thanks.
When connected over USB2, this device reports a nonsense
bInterfaceProtocol value 6 and doesn't work with usb-storage. When
connected over USB1, the device reports the correct bInterfaceProtocol
value 0x50 (bulk) and works with no problems.
Signed-off-by: Daniel Drake <dsd@gentoo.org> Signed-off-by: Phil Dibowitz <phil@ipom.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds entries for several USB floppies that need
the US_FL_SINGLE_LUN flag. These were reported by
Sebastian Kapfer <sebastian_kapfer@gmx.net> and Olaf Hering
<olh@suse.de>, with rediffing and cleaning from me.
Reported-by: Sebastian Kapfer <sebastian_kapfer@gmx.net> Reported-by: Olaf Hering <olh@suse.de> Signed-off-by: Phil Dibowitz <phil@ipom.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Pete Zaitcev [Tue, 23 Aug 2005 14:46:13 +0000 (07:46 -0700)]
[PATCH] USB Storage: unusual_devs.h request for Transcend
The stick replies to the door lock commands with a check condition (e.g.
FAIL status in a normal bulk CSW), but the subsequent REQUEST SENSE
returns all-zero sense. The situation is documented in our Bugzilla,
including usbmon traces.
https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=162559
The error is purely cosmetic, data integrity is not in danger.
But I thought we might as well do it. It looks nicer that way.
I discussed this with Phil and he told me to submit directly.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com> Signed-off-by: Phil Dibowitz <phil@ipom.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Matthew Dharm [Fri, 26 Aug 2005 03:03:50 +0000 (20:03 -0700)]
[PATCH] USB: storage: Fix messed-up locking
This is patch as550 from Alan Stern.
Apparently someone changed the SCSI core so that it no longer holds the
host lock when doing a device or bus reset. usb-storage was updated at
the time, but the change was done carelessly. Some of the code depends
on that lock being held.
This patch reintroduces the host lock where needed and tries to clarify
the comments explaining why the lock is necessary. It also moves the
code that clears the TIMED_OUT and ABORTING bitflags so that it executes
as soon as the timed-out command has completed (and while the host lock
is held).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Wed, 31 Aug 2005 17:41:44 +0000 (10:41 -0700)]
[PATCH] USB: relax usbcore reset timings
This appears to help some folk, please merge.
This patch relaxes reset timings. There are some reports that it
helps make enumeration work better on some high speed devices.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Randy Dunlap [Fri, 9 Sep 2005 04:56:56 +0000 (21:56 -0700)]
[PATCH] USB: proc_usb_info.txt: add blank lines
Update Documentation/usb/proc_usb_info.txt:
- remove some trailing whitespace
- add a blank line before each T: line to match current kernel
and to make the text more readable.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Robert Spanton [Tue, 30 Aug 2005 22:38:23 +0000 (23:38 +0100)]
[PATCH] USB: PL2303: CA-42 Phone cable
This patch adds the product ID and vendor ID for a Nokia CA-42 USB cable
to the list of devices handled by the pl2303 driver. The patch is
against 2.6.13.
Signed-off-by: Robert Spanton <rds204@zepler.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Wed, 31 Aug 2005 18:54:09 +0000 (11:54 -0700)]
[PATCH] USB: OHCI, pxa27x OHCI port power tweaks
Now that it's in use on other boards, a bug in the original code needs fixing.
There is no need for the PXA27x OHCI to set usb power during init, since
the hub driver in usbcore handles that. Those platform-specific power
control functions are also incorrect, and should therefore be removed.
Add a check to clear the OTG pin hold bit until such times OTG is
properly implemented.
Signed-Off-By: Richard Purdie <rpurdie@rpsys.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Wed, 31 Aug 2005 18:52:57 +0000 (11:52 -0700)]
[PATCH] USB: OHCI relies less on NDP register
Some OHCI implementations have differences in the way the NDP register
(in roothub_a) reports the number of ports present. This patch allows the
platform specific code to optionally supply the number of ports. The
driver just reads the value at init (if not supplied) instead of reading
it every time its needed (except for an AMD756 bug workaround).
It also sets the value correctly for the ARM pxa27x architecture.
Signed-Off-By: Richard Purdie <rpurdie@rpsys.net> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Wed, 31 Aug 2005 17:47:20 +0000 (10:47 -0700)]
[PATCH] USB: OHCI irq tweak
Evidently there are some boards which care a lot about this, but
as a rule it's been hard to notice.
OHCI_INTR_RD wasn't always cleared in the ohci irq handler. On some
systems this means certain remote wakeup scenarios could seem to hang
(in an interrupt storm, RD never clearing).
From: "William Morrow" <William.Morrow@amd.com> Signed-off-by: Jordan Crouse <jordan.crouse@amd.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Wed, 31 Aug 2005 17:45:25 +0000 (10:45 -0700)]
[PATCH] USB: get rid of minor log spamming
Routine cases like handoff-to-companion shouldn't trigger diagnostics.
This gets rid of some recently added log spamming. It's routine for
hub_port_wait_reset() to return -ENOTCONN to indicate handoff from
highspeed hubs to companions, so an error message is incorrect.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Sat, 3 Sep 2005 01:58:09 +0000 (18:58 -0700)]
[PATCH] USB: EHCI workaround for NForce and mem > 2GB
NVidia reports (via Mark Overby) that some of their EHCI controllers
don't like certain data structure addresses beyond the 2GB mark.
He provided an earlier version of this patch.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Wed, 31 Aug 2005 17:55:38 +0000 (10:55 -0700)]
[PATCH] USB: EHCI port tweaks
One change may improve some S1 or S3 resume cases, and the other
seems mostly to explain some strange state "lsusb" would show.
Two fixes:
- On resume, don't think about resuming any unpowered port, or
resetting any port with OWNER set to the OHCI/UHCI companion.
This will make some S1 and S3 resume scenarios work better.
- PORT_CSC was not being cleared correctly in ehci_hub_status_data.
This was visible at least through current versions of "lsusb",
and might have caused some other hub related strangeness.
The fix addresses all three write-to-clear bits, using the same
approach that UHCI happens to use: a mask of bits that are
cleared in most writes to that port status register.
Original patch seems to have been from from William.Morrow@amd.com
and this version (from David) finishes the write-to-clear changes.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Mon, 5 Sep 2005 17:59:51 +0000 (13:59 -0400)]
[PATCH] USB UHCI: remove the FSBR kernel timer
This patch (as558) removes from the UHCI driver a kernel timer used for
checking Full Speed Bandwidth Reclamation (FSBR). The checking can be
done during normal root-hub polling; it doesn't need a separate timer.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Mon, 5 Sep 2005 17:55:23 +0000 (13:55 -0400)]
[PATCH] usbcore: small changes to HCD glue layer
This patch (as549) introduces two small changes in the HCD glue layer.
The first simply removes a redundant test. The second allows root-hub
polling to continue for a single iteration after a host controller dies;
this is needed for the patch that follows.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stelian Pop [Thu, 8 Sep 2005 08:19:48 +0000 (10:19 +0200)]
[PATCH] USB: add apple usb touchpad driver
This is a driver for the USB touchpad which can be found on post-February 2005
Apple PowerBooks.
This driver is derived from Johannes Berg's appletrackpad driver [1],
but it has been improved in some areas:
* appletouch is a full kernel driver, no userspace program is necessary
* appletouch can be interfaced with the synaptics X11 driver[2], in order
to have touchpad acceleration, scrolling, two/three finger tap, etc.
This driver has been tested by the readers of the 'debian-powerpc' mailing
list for a few weeks now and I believe it is now ready for inclusion into the
mainline kernel.
Credits go to Johannes Berg for reverse-engineering the touchpad protocol,
Frank Arnold for further improvements, and Alex Harper for some additional
information about the inner workings of the touchpad sensors.
Signed-off-by: Stelian Pop <stelian@popies.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
here is a new and extended version of the sisusbvga (previously: sisusb)
driver. The patch is against 2.6.13 and updates the driver to version 0.0.8.
Additions include complete VGA/EGA text console support and a build-in
display mode infrastructure for userland applications that don't know
about the graphics internals.
Fixes include some BE/LE issues and a get/put_dev bug in the previous
version.
Other changes include a change of the module name from "sisusb" to
"sisusbvga". The previous one was too generic IMHO.
Please note that the patch also affects the Makefile in
drivers/video/console as the driver requires the VGA 8x16 font in case
the text console part is selected.
Heavily tested, as usual. Please apply.
One thing though: I already prepared for removal of the "mode" field and
the changed "name" field in the usb_class_driver structure. This will
perhaps need some refinement depending on whether you/Linus merge the
respective core changes before or after 2.6.14.
Signed-off-by: Thomas Winischhofer <thomas@winischhofer.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is the same patch that went into i386 just before 2.6.13
came out. I still can't build 64-bit user apps, so I tested
with program (see below) in 32-bit mode on 64-bit kernel:
Before:
$ fpsig
handler: nr = 8, si = 0x0804bc90, vuc = 0x0804bd10
handler: altstack is at 0x0804b000, ebp = 0x0804bc7c
handler: si_signo = 8, si_errno = 0, si_code = 0 [unknown]
handler: fpu cwd = 0xb40, fpu swd = 0xbaa0
handler: i387 unmasked precision exception, rounded up
After:
$ fpsig
handler: nr = 8, si = 0x0804bc90, vuc = 0x0804bd10
handler: altstack is at 0x0804b000, ebp = 0x0804bc7c
handler: si_signo = 8, si_errno = 0, si_code = 6 [inexact result]
handler: fpu cwd = 0xb40, fpu swd = 0xbaa0
handler: i387 unmasked precision exception, rounded up
Jan Beulich [Mon, 12 Sep 2005 16:49:24 +0000 (18:49 +0200)]
[PATCH] x86-64: Fix CFI information
Being the foundation for reliable stack unwinding, this fixes CFI unwind
annotations in many low-level x86_64 routines, plus a config option
(available to all architectures, and also present in the previously sent
patch adding such annotations to i386 code) to enable them separatly
rather than only along with adding full debug information.
[PATCH] x86-64: Remove freeing of SMP trampoline pages
Nick points out it never worked because PageReserved was
set and it might cause problems later on. Also HOTPLUG_CPU
is much more common now so let's care not too much
about the !hotplug case.
Needed for some newer Opteron systems with E stepping and memory
relocation enabled. The node addresses are different in lower
bits now so the nodemap hash function needs to be enlarged.
If one of the arguments (in the _llseek syscall it's the arg4) is a pointer
which the syscall is expected to write to (to the memory pointed to by this
ptr), then this side-effect is not captured in the asm.
If anyone uses this macro to define it's own version of the syscall
(sometimes necessary when not using glibc) and it's inlined, then GCC
doesn't know that this asm write to "*dest", when called like so for instance:
out = 1;
llseek (fd, bla, blubb, &out, trara)
use (out);
Here nobody tells GCC that "out" actually is written to (just a pointer to it
is passed to the asm). Hence GCC might (and in the above bug did)
copy-propagate "1" into the second use of "out".
The easiest solution would be to add a "memory" clobber to the definition
of this syscall macro. As this is a syscall, it shouldn't inhibit too many
optimizations.
The generic TLB flush functions kept upto 506 pages per
CPU to avoid too frequent IPIs.
This value was done for the L1 cache of older x86 CPUs,
but with modern CPUs it does not make much sense anymore.
TLB flushing is slow enough that using the L2 cache is fine.
This patch increases the flush array on x86-64 to cache
5350 pages. That is roughly 20MB with 4K pages. It speeds
up large munmaps in multithreaded processes on SMP considerably.
The cost is roughly 42k of memory per CPU, which is reasonable.
I only increased it on x86-64 for now, but it would probably
make sense to increase it everywhere. Embedded architectures
with SMP may keep it smaller to save some memory per CPU.
[PATCH] x86-64: Make remote TLB flush more scalable
Instead of using a global spinlock to protect the state
of the remote TLB flush use a lock and state for each sending CPU.
To tell the receiver where to look for the state use 8 different
call vectors. Each CPU uses a specific vector to trigger flushes on other
CPUs. Depending on the received vector the target CPUs look into
the right per cpu variable for the flush data.
When the system has more than 8 CPUs they are hashed to the 8 available
vectors. The limited global vector space forces us to this right now.
In future when interrupts are split into per CPU domains this could be
fixed, at the cost of needing more IPIs in flat mode.
Also some minor cleanup in the smp flush code and remove some outdated
debug code.
Requires patch to move cpu_possible_map setup earlier.
If we use 64bit kernel on ia64/x86_64/s390 architecture, and we run
32bit binary on 32bit compatibility mode, sendfile system call seems be
not set offset argument.
This is because sendfile's return value is not zero but the code regards
the result by return value is zero or not.
This problem will be affect to ia64/x86_64/s390 and not affect to other
architecture does not affect other architecture (mips/parisc/ppc64/sparc64).
[PATCH] x86-64: Make lockless machine check record passing a bit more robust.
One machine is constantly throwing NMI watchdog timeouts in mce_log
This was one attempt to fix it.
(AK: this doesn't actually fix the bug I'm seeing unfortunately, probably
drop. I don't like it that the reader can spin forever now waiting
for a writer)
This leads to bootmem allocating first from node 0 instead
of from the last node. This avoids swiotlb allocating on the last node, which
doesn't really work on a machine with >4GB.
Note: there is a better patch around from someone else that gets
rid of the pgdat list completely.
[PATCH] x86-64: Avoid unnecessary double bouncing for swiotlb
PCI_DMA_BUS_IS_PHYS has to be zero even when the GART IOMMU is disabled
and the swiotlb is used. Otherwise the block layer does unnecessary
double bouncing.
[PATCH] x86-64: Support dualcore and 8 socket systems in k8 fallback node parsing
In particular on systems where the local APIC space and node space
is very different from the Linux CPU number space.
Previously the older NUMA setup code directly parsing the K8
northbridge registers had some issues on 8 socket or dual core
systems. This patch fixes them.
This is mainly done by fixing some confusion between Linux
CPU numbers and local APIC ids. We now pass the local APIC IDs
to later code, which avoids mismatches.
Also add some heuristics to detect cases where the Hypertransport
nodeids and the local APIC IDs don't match, but are shifted
by a constant offset.
This is still all quite hackish, hopefully BIOS writers fill
in correct SRATs instead.
[PATCH] x86-64: Don't assign CPU numbers in SRAT parsing
Do that later when the CPU boots. SRAT just stores the APIC<->Node
mapping node. This fixes problems on systems where the order
of SRAT entries does not match the MADT.
projects / linux-2.6 / log