- Make FE_READ_UNCORRECTED_BLOCKS reset the count after each call,
thus returning a momentary value like all other demods do,
instead of an absolute, ever increasing count.
Signed-off-by: Stephen Williams <stephen.williams@gmail.com> Signed-off-by: Johannes Stezenbach <js@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
V4L/DVB (3118): Enable remote control on AVERTV STUDIO 303
- Enable remote control on AVERTV STUDIO 303
- This patch adapted from a patch found on a website posted by
an anonymous user. Thanks to original anonymous author for
creating this patch. Tested successfully by George Gazurkoff.
Signed-off-by: George Gazurkoff <gazurkoff@gmail.com> Signed-off-by: Michael Krufky <mkrufky@m1k.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Set the tuner takeover point to 0x10 for NTSC/radio and 0x14 for PAL/SECAM.
- Allow override through TDA9887_SET_CONFIG
- PAL-N belongs with PAL-BG as does PAL-H. PAL-Nc belongs to PAL-M
- Add SECAM-BGH
- Set video freq to cVideoIF_38_90 for DK standards.
- Add cTunerGainLow to radio, change deemphasis to 75 for mono.
- Add ntsc module param for 'M' and 'J' (Japanese) standards.
- Fix module handling for 2.4.
- Now able to select all standards through pal/secam/ntsc module options
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Steven Toth [Mon, 9 Jan 2006 17:25:17 +0000 (15:25 -0200)]
V4L/DVB (3112): Several fixes for Hauppauge Roselyn Design (blackbird)
- This patch adds eeprom awareness for the Roslyn. In effect, the
blackbird will query the tuner V4L2_STD_xxxx definitions to determine
whether it's connected to a NTSC or PAL tuner. Based on that, various
default values will change for blackbird encoding.
- Fixes back panel SVIDEO/COMPOSITE with audio, work properly.
- Fixes a problem with lip sync issues, due to bad framerate vs
audio rate assumptions.
- Fixed a problem with the GPIO configuration in cx88-cards.
- Removed the comments in cx88-cards that made no sense.
Signed-off-by: Steven Toth <stoth@hauppauge.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Otavio Salvador [Mon, 9 Jan 2006 17:25:17 +0000 (15:25 -0200)]
V4L/DVB (3110): Replace all uses of pci_module_init with pci_register_driver
This patch replace all calls to pci_module_init, that's deprecated and
will be removed in future, with pci_register_driver that should be
the used function now.
Signed-off-by: Otavio Salvador <otavio@debian.org> Signed-off-by: Michael Krufky <mkrufky@m1k.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Hans Verkuil [Mon, 9 Jan 2006 17:25:14 +0000 (15:25 -0200)]
V4L/DVB (3100): fix compile error, remove dead code and volume scaling
- Fix compile error (missing '}') in em28xx-video.c. Remove dead code and
volume scaling from msp3400.c. Volume scaling does not belong there, it should
be done in the driver for the card that uses the msp3400 if needed, not in the
msp3400.c source. The volume scaling code gave problems with the ivtv driver
which does not need to do any scaling.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Noone Important [Mon, 9 Jan 2006 17:25:09 +0000 (15:25 -0200)]
DVB (2390): Adds a time-delay to IR remote button presses for av7110 ir input,
- Adds a time-delay to IR remote button presses for av7110_ir input,
such that it acts more like a keyboard. A short press will be treated
as a single button press. Holding down a button on the remote will
respond like holding down a key on the keyboard, and result in a
key-repeat. This just introduces a delay between the 1st press, and
going into key-repeat so that it is possible to get a single 'up'.
Signed-off-by: Noone Important <nxhxzi702 at sneakemail.com> Signed-off-by: Oliver Endriss <o.endriss@gmx.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Vadim Catana [Mon, 9 Jan 2006 17:25:08 +0000 (15:25 -0200)]
DVB (2451): Add support for KWorld DVB-S 100, based on the same chips as Hauppauge
- Add support for KWorld DVB-S 100, based on the same chips as Hauppauge
Nova-S Plus (CX23883/CX24123/CX24109), without the Intersil ISL6421,
which is used for LNB control.
- LNB voltage and tone are controled by LNBDC and LNBTone bits from
register 0x29 of the CX24123 demodulator.
- The MO_GP0_IO register from CX23883 is used to turn LNB power on and off.
Signed-off-by: Vadim Catana <skystar@moldova.cc> Acked-by: Johannes Stezenbach <js@linuxtv.org> Signed-off-by: Michael Krufky <mkrufky@m1k.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Dr. Werner Fink [Mon, 9 Jan 2006 17:25:07 +0000 (15:25 -0200)]
DVB (2441): Driver support for live-ac3, firmware >= 2621 required.
- Driver support for live-ac3, firmware >= 2621 required.
Signed-off-by: Dr. Werner Fink <werner@suse.de> Signed-off-by: Oliver Endriss <o.endriss@gmx.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Oliver Endriss [Mon, 9 Jan 2006 17:25:06 +0000 (15:25 -0200)]
DVB (2432): LNB power can now be switched off for Activy Budget-S rev GR/AL.
- LNB power can now be switched off for Activy Budget-S rev GR/AL.
Dishnetwork support fixed for Nova-S with bsbe1/lnbp21 frontend and
Activy Budget-S rev AL.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
DVB (2420): Makes integration of future devices easier
- To make the integration of future devices easier
- modified the dvb-usb-part to allow a device-specific firmware download
- added an option to specify whether a device reconnects after a firmware download or not.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
V4L (0988): Tuner cleanups by removing Video IF from tuners struct
- Video IF was removed from tuners struct.
- Each Video standard have its own Video IF frequency, so it
is related to video standard. Of course tuner also needs
saw filters for IF, but this way, similar tuners can be grouped
into just one entry, if they have the same cut-off freqs and
the same switch config and global config.
Vadim Catana [Mon, 9 Jan 2006 17:25:02 +0000 (15:25 -0200)]
V4L (1007): Add support for KWorld DVB-S 100
- Add support for KWorld DVB-S 100, based on the same chips as Hauppauge
Nova-S Plus (CX23883/CX24123/CX24109), without the Intersil ISL6421,
which is used for LNB control.
- LNB voltage and tone are controled by LNBDC and LNBTone bits from
register 0x29 of the CX24123 demodulator.
- The MO_GP0_IO register from CX23883 is used to turn LNB power on and off.
Signed-off-by: Vadim Catana <skystar@moldova.cc> Acked-by: Johannes Stezenbach <js@linuxtv.org> Signed-off-by: Michael Krufky <mkrufky@m1k.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Steven Toth [Mon, 9 Jan 2006 17:25:02 +0000 (15:25 -0200)]
V4L (0979): Added V4L support for the Nova-S-Plus and Nova-SE2 DVB-S products
- Added V4L support for the Nova-S-Plus and Nova-SE2 DVB-S products.
- Basic DVB-S support is working, analog video inputs work.
- It has one or two fixme comments, primarily analog GPIOs (audio) and eeprom parsing.
- CX24123 code (in cx88-dvb.c) disabled until the
- cx24123 module is added to dvb-kernel cvs.
Signed-off-by: Steven Toth <stoth@hauppauge.com> Signed-off-by: Michael Krufky <mkrufky@m1k.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Arnd Bergmann [Mon, 9 Jan 2006 17:24:57 +0000 (15:24 -0200)]
V4L (926_2): Moves compat32 functions from fs to v4l subsystem
This moves the 32 bit ioctl compatibility handlers for
Video4Linux into a new file and adds explicit calls to them
to each v4l device driver.
Unfortunately, there does not seem to be any code handling
the v4l2 ioctls, so quite often the code goes through two
separate conversions, first from 32 bit v4l to 64 bit v4l,
and from there to 64 bit v4l2. My patch does not change
that, so there is still much room for improvement.
Also, some drivers have additional ioctl numbers, for
which the conversion should be handled internally to
that driver.
Dan Williams [Mon, 9 Jan 2006 16:04:31 +0000 (11:04 -0500)]
[patch] ipw2100: support WEXT-18 enc_capa v3
This patch allows ipw2100 driver to advertise the WPA-related encryption
options that it does really support. It's necessary to work correctly
with NetworkManager and other programs that actually check driver & card
capabilities.
Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Denis Vlasenko [Fri, 6 Jan 2006 06:45:47 +0000 (22:45 -0800)]
[PATCH] fix a few "warning: 'cleanup_card' defined but not used"
These warnings are emitted if non-modular network drivers are built.
Fixes just move cleanup_card() definitions into #ifdef MODULE region.
/.1/usr/srcdevel/kernel/linux-2.6.15-rc7.src/drivers/net/wd.c:131: warning: 'cleanup_card' defined but not used
/.1/usr/srcdevel/kernel/linux-2.6.15-rc7.src/drivers/net/3c503.c:152: warning: 'cleanup_card' defined but not used
/.1/usr/srcdevel/kernel/linux-2.6.15-rc7.src/drivers/net/ne.c:216: warning: 'cleanup_card' defined but not used
/.1/usr/srcdevel/kernel/linux-2.6.15-rc7.src/drivers/net/hp.c:106: warning: 'cleanup_card' defined but not used
/.1/usr/srcdevel/kernel/linux-2.6.15-rc7.src/drivers/net/hp-plus.c:142: warning: 'cleanup_card' defined but not used
/.1/usr/srcdevel/kernel/linux-2.6.15-rc7.src/drivers/net/smc-ultra.c:172: warning: 'cleanup_card' defined but not used
/.1/usr/srcdevel/kernel/linux-2.6.15-rc7.src/drivers/net/e2100.c:144: warning: 'cleanup_card' defined but not used
/.1/usr/srcdevel/kernel/linux-2.6.15-rc7.src/drivers/net/es3210.c:159: warning: 'cleanup_card' defined but not used
/.1/usr/srcdevel/kernel/linux-2.6.15-rc7.src/drivers/net/lne390.c:149: warning: 'cleanup_card' defined but not used
/.1/usr/srcdevel/kernel/linux-2.6.15-rc7.src/drivers/net/lance.c:313: warning: 'cleanup_card' defined but not used
/.1/usr/srcdevel/kernel/linux-2.6.15-rc7.src/drivers/net/ac3200.c:127: warning: 'cleanup_card' defined but not used
Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Ayaz Abdulla [Fri, 6 Jan 2006 06:45:45 +0000 (22:45 -0800)]
[PATCH] forcedeth: TSO fix for large buffers
This contains a bug fix for large buffers. Originally, if a tx buffer to
be sent was larger then the maximum size of the tx descriptor, it would
overwrite other control bits. In this patch, the buffer is split over
multiple descriptors. Also, the fragments are now setup in forward order.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com> Signed-off-by: Manfred Spraul <manfred@colorfullife.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Olaf Hering [Fri, 6 Jan 2006 06:45:45 +0000 (22:45 -0800)]
[PATCH] remove bouncing mail address of mv643xx_eth maintainer
Remove bouncing mail address of mv643xx maintainer.
Signed-off-by: Olaf Hering <olh@suse.de> Cc: Jeff Garzik <jgarzik@pobox.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de> Cc: "David S. Miller" <davem@davemloft.net> Cc: Jeff Garzik <jgarzik@pobox.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de> Cc: "David S. Miller" <davem@davemloft.net> Cc: Jeff Garzik <jgarzik@pobox.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Adrian Bunk [Fri, 6 Jan 2006 06:45:41 +0000 (22:45 -0800)]
[PATCH] drivers/net/Kconfig: indentation fix
This patch fixes a wrong indentation.
Signed-off-by: Adrian Bunk <bunk@stusta.de> Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Eric Paris [Fri, 6 Jan 2006 16:57:11 +0000 (11:57 -0500)]
[PATCH] update bonding.txt to not show ip address on slaves
ifenslave, as of abi version 2, does not set the ip address on the slave
interfaces. The documentation example however still shows that the
ensalved interfaces should have the same IP as the master. The patch
simply removes the lines from the example which should no longer appear.
Signed-off-by: Eric Paris <eparis@redhat.com>
bonding.txt | 2 --
1 files changed, 2 deletions(-) Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
[PATCH] tulip: enable multiport NIC BIOS fixups for x86_64
A BIOS bug affecting some multiport tulip NICs requires an irq fixup
in tulip_core.c. This has only been enabled for i686, but it is
needed for x86_64 as well.
Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Andrew Chew [Thu, 5 Jan 2006 03:13:04 +0000 (19:13 -0800)]
[PATCH] sata_nv, spurious interrupts at system startup with MAXTOR 6H500F0 drive
This patch works around a problem with spurious interrupts seen at boot time when
a MAXTOR 6H500F0 drive is present. An ATA interrupt condition is mysteriously
present at start of day. If we took too long in issuing the first command,
the kernel would basically get tired of the spurious interrupts and turn the interrupt
off. Issuing the first command essentially causes the interrupt condition to
get acknowledged.
I haven't seen this happen with any other drives.
What I basically do is ack ATA status by reading it regardless of whether we're
expecting to have to handle an interrupt. This clears the start-of-day anomalous
interrupt condition, and keeps the kernel from disabling that interrupt due to
too many spurious interrupts.
Also, I fixed a bug where hotplug interrupts weren't getting acknowledged as handled
in the ISR. This was not the cause of the spurious interrupts, but it's the right
thing to do anyway.
Signed-Off-By: Andrew Chew Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Eugene Surovegin [Tue, 27 Dec 2005 20:36:41 +0000 (12:36 -0800)]
[PATCH] PPC44x EMAC driver: disable TX status deferral in half-duplex mode
Disable TX status deferral (EMACx_MR[MWSW=001]) in half-duplex mode.
I have two reports when EMAC stops transmitting when connected to a
hub. TX ring debug printouts show complete mess when this happens,
probably hardware collision handling doesn't work quite well in this
mode.
This is relevant only for SoCs with EMAC4 core (440GX, 440SP, 440SPe).
Tested on 440GX.
Signed-off-by: Eugene Surovegin <ebs@ebshome.net> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Johannes Berg [Sat, 31 Dec 2005 10:35:20 +0000 (11:35 +0100)]
[PATCH] ieee80211: enable hw wep where host has to build IV
This patch fixes some of the ieee80211 crypto related code so that
instead of having the host fully do crypto operations, the host_build_iv
flag works properly (for WEP in this patch) which, if turned on,
requires the hardware to do all crypto operations, but the ieee80211
layer builds the IV. The hardware also has to build the ICV.
Previously, the host_build_iv flag couldn't be used at all for WEP, and
not alone (with both host_decrypt and host_encrypt disabled) because the
crypto algorithm wasn't assigned. This is also fixed.
I have tested this patch both in host crypto mode and in hw crypto mode
(with the Broadcom chipset).
[resent, signing digitally caused it to be MIME-junked, sorry]
Signed-Off-By: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
[PATCH] sk98lin: error handling on dual port board
Sk98lin driver error recovery on two port boards is bad.
If it fails the second allocation, it will not release resources
properly. Also it registers the second port in the pci driver data
If second port fails, might as well go with one port.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Sk98lin 64bit memory handling is wrong. It doesn't set the
highdma flag; i.e. the kernel always does bounce buffers.
It doesn't fallback to 32 bit mask if it can't get 64 bit mask.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
[PATCH] sk98lin: routine called from probe marked __init
Sk98lin driver has a routine marked __init that is called from
the probe code. If using pci hotplug, this could be called after
the initialization so it needs to be marked __devinit.
So if you hot added a sk98lin board, the kernel would crash.
I don't have hot plug hardware to actually try this feat.
Also, there are two routines, only called from SkGeBoardInit that can
be marked __devinit.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Jens Axboe [Mon, 9 Jan 2006 15:03:35 +0000 (16:03 +0100)]
[IDE] Use the block layer deferred softirq request completion
This patch makes IDE use the new blk_complete_request() interface.
There's still room for improvement, as __ide_end_request() really
could drop the lock after getting HWGROUP->rq (why does it need to
hold it in the first place? If ->rq access isn't serialized, we are
screwed anyways).
Jens Axboe [Mon, 9 Jan 2006 15:02:34 +0000 (16:02 +0100)]
[BLOCK] ll_rw_blk: Enable out-of-order request completions through softirq
Request completion can be a quite heavy process, since it needs to
iterate through the entire request and complete the bio's it holds.
This patch adds blk_complete_request() which moves this processing
into a dedicated block softirq.
Jens Axboe [Mon, 9 Jan 2006 14:30:20 +0000 (15:30 +0100)]
[BLOCK] Kill blk_attempt_remerge()
It's a broken interface, it's done way too late. And apparently it triggers
slab problems in recent kernels as well (most likely after the generic dispatch
code was merged). So kill it, ide-cd is the only user of it.
Paul Mackerras [Mon, 9 Jan 2006 09:17:01 +0000 (20:17 +1100)]
powerpc: set CONFIG_PPC_OF=y always for ARCH=powerpc
The CONFIG_PPC_OF symbol is used to mean that the firmware device tree
access functions are available. Since we always have a device tree
with ARCH=powerpc, make CONFIG_PPC_OF always Y for ARCH=powerpc.
This fixes some compile errors reported by Kumar Gala, but in a
different way to his patch. This also makes prom_parse.o be compiled
only if CONFIG_PPC_OF so that non-OF ARCH=ppc platforms will compile.
Anton Blanchard [Mon, 9 Jan 2006 04:47:04 +0000 (15:47 +1100)]
[PATCH] powerpc: DABR exceptions should report the address not the PC
When taking a DABR exception we were reporting the PC. It makes more
sense to report the address that caused the exception, and the gdb guys
would like it that way.
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Anton Blanchard [Mon, 9 Jan 2006 04:41:31 +0000 (15:41 +1100)]
[PATCH] ppc64: Fix oprofile when compiled as a module
My recent changes to oprofile broke it when built as a module. Fix it by
using an enum instead of a function pointer. This way we still retain
the oprofile configuration in the cputable.
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
[PATCH] 4/5 powerpc: Add cpufreq support for all desktop G5
This patch adds cpufreq support for all desktop "tower" G5 models. The
only G5 models still lacking cpufreq support at this point are the
Xserve and possibly the new iMac iSight (not tested). I'll have those
added soon. That patch uses the new platform functions interpreter to
implement frequency and voltage switching on most models.
Note that in order to find the low frequency value, I had to hack
something that might now work properly on all models, so if the
frequency value reported when running low speed looks bogus to you,
please report it to me. (Appart from a bogus reported value, things
should work fine).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
This is the platform function interpreter itself along with the backends
for UniN/U3/U4, mac-io, GPIOs and i2c. It adds the ability to execute
those do-platform-* scripts in the device-tree (at least for most
devices for which a backend is provided). This should replace the clock
spreading hacks properly. It might also have an impact on all sort of
machines since some of the scripts marked "at init" will now be executed
on boot (or some other on sleep/wakeup), those will possibly do things
that the kernel didn't do at all, like setting some values into some i2c
devices (changing thermal sensor calibration or conversion rate) etc...
Thus regression testing is MUCH welcome. Also loook for errors in dmesg.
That's also why I've left rather verbose debugging enabled in this
version of the patch.
(I do expect some Windtunnel G4s to show some errors as they have an i2c
clock chip on the PMU bus that uses some primitives that the i2c backend
doesn't implement yet. I really need users that have one of those
machine to come back to me so we can get that done right, though the
errors themselves should be harmless, I suspect the machine might not
run at full speed).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
This is the continuation of the previous patch. This one removes the old
PowerMac i2c drivers (i2c-keywest and i2c-pmac-smu) and replaces them
both with a single stub driver that uses the new PowerMac low i2c layer.
Now that i2c-keywest is gone, the low-i2c code is extended to support
interrupt driver transfers. All i2c busses now appear as platform
devices. Compatibility with existing drivers should be maintained as the
i2c bus names have been kept identical, except for the SMU bus but in
that later case, all users has been fixed.
With that patch added, matching a device node to an i2c_adapter becomes
trivial.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
This is the first part of a rework of the PowerMac i2c code. It
completely reworks the "low_i2c" layer. It is now more flexible,
supports KeyWest, SMU and PMU i2c busses, and provides functions to
match device nodes to i2c busses and adapters.
This patch also extends & fix some bugs in the SMU driver related to i2c
support and removes the clock spreading hacks from the pmac feature code
rather than adapting them to the new API since they'll be replaced by
the platform function code completely in patch 3/5
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Anton Blanchard [Fri, 6 Jan 2006 13:49:49 +0000 (00:49 +1100)]
[PATCH] ppc64: fix time syscall
ppc64 has its own version of sys_time. It looks pretty scary, touching
a whole bunch of variables without any locking or memory ordering.
In fact, a recent bugreport has shown it can actually go backwards. Time
to remove it and just use the generic sys_time, which is implemented on
top of do_gettimeofday.
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
The addition of the .text section definition in the definition of
_GLOBAL overrides the .relocate_code section definition. As a result,
these two functions don't end up in .relocate_code, so they don't get
relocated correctly, and the boot fails.
There's another suspicious-looking usage at kernel/swsusp.S:37 that
someone should look into. I did not exhaustively search the source
tree, though.
The following is the minimal patch that fixes the immediate problem.
I could easily be convinced that the _GLOBAL definition should be
modified to remove the ".text;" line either instead of, or in addition
to, this fix.
Signed-off-by: Paul Janzen <pcj@linux.sez.to> Signed-off-by: Paul Mackerras <paulus@samba.org>
Arnd Bergmann [Thu, 5 Jan 2006 14:05:29 +0000 (14:05 +0000)]
[PATCH] spufs: set irq affinity for running threads
For far, all SPU triggered interrupts always end up on
the first SMT thread, which is a bad solution.
This patch implements setting the affinity to the
CPU that was running last when entering execution on
an SPU. This should result in a significant reduction
in IPI calls and better cache locality for SPE thread
specific data.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Arnd Bergmann [Wed, 4 Jan 2006 19:31:32 +0000 (20:31 +0100)]
[PATCH] spufs: fix allocation on 64k pages
The size of the local store is architecture defined
and independent from the page size, so it should
not be defined in terms of pages in the first place.
This mistake broke a few places when building for
64kb pages.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Arnd Bergmann [Wed, 4 Jan 2006 19:31:30 +0000 (20:31 +0100)]
[PATCH] spufs: abstract priv1 register access.
In a hypervisor based setup, direct access to the first
priviledged register space can typically not be allowed
to the kernel and has to be implemented through hypervisor
calls.
As suggested by Masato Noguchi, let's abstract the register
access trough a number of function calls. Since there is
currently no public specification of actual hypervisor
calls to implement this, I only provide a place that
makes it easier to hook into.
Arnd Bergmann [Wed, 4 Jan 2006 19:31:29 +0000 (20:31 +0100)]
[PATCH] spufs: move spu_run call to its own file
The logic for sys_spu_run keeps growing and it does
not really belong into file.c any more since we
moved away from using regular file operations to our
own syscall.
No functional change in here.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>