Dave Jones [Wed, 1 Jun 2005 02:03:46 +0000 (19:03 -0700)]
[CPUFREQ] dual-core powernow-k8
With the release of the dual-core AMD Opterons last week,
it's high time that cpufreq supported them. The attached
patch applies cleanly to 2.6.12-rc3 and updates powernow-k8
to support the latest Athlon 64 and Opteron processors.
Update the driver to version 1.40.0 and provide support
for dual-core processors.
Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com> Signed-off-by: Dave Jones <davej@redhat.com>
Dave Jones [Wed, 1 Jun 2005 02:03:45 +0000 (19:03 -0700)]
[CPUFREQ] Recalibrate cpu_khz [1/2]
We have to recalibrate cpu_khz in order to use the current FID instead the max
FID since some BIOS do not put the processor at maximum frequency at POST.
Also, some BIOS will change the processor frequency at our back after cpu_khz
was calibrate. Finally, this will fix a long standing bug when we do
something like this:
# rmmod powernow-k7
# modprobe powernow-k7
Signed-off-by: Bruno Ducrot <ducrot@poupinou.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Dave Jones <davej@redhat.com>
Dave Jones [Wed, 1 Jun 2005 02:03:44 +0000 (19:03 -0700)]
[CPUFREQ] speedstep-smi: it works on at least one P4M
The speedstep-smi driver actually works on >=1 notebook with a
Pentium 4-M CPU where all other cpufreq drivers fail. Therefore,
allow speedstep-smi on P4Ms again, but warn users of likely failure
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net> Signed-off-by: Dave Jones <davej@redhat.com>
Dave Jones [Wed, 1 Jun 2005 02:03:44 +0000 (19:03 -0700)]
[CPUFREQ] ondemand: trivial clean-ups
Trivial ondemand governor clean-ups:
- change from sampling_rate_in_HZ() to the official function
usecs_to_jiffies().
- use for_each_online_cpu() to instead of using "if (cpu_online(i))"
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net> Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net> Signed-off-by: Dave Jones <davej@redhat.com>
Dave Jones [Wed, 1 Jun 2005 02:03:43 +0000 (19:03 -0700)]
[CPUFREQ] speedstep-centrino: Pentium 4 - M (HT) support
The Pentium 4 - Ms (HT) with CPUID 0xF34 and 0xF41 seem to support
centrino-like enhanced speedstep; however, no "table" support is possible.
Therefore, put NULL entries into speedstep-centrino.c
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net> Signed-off-by: Dave Jones <davej@redhat.com>
Dave Jones [Wed, 1 Jun 2005 02:03:43 +0000 (19:03 -0700)]
[CPUFREQ] cpufreq-core: reduce warning messages.
cpufreq core is printing out messages at KERN_WARNING level that the core
recovers from without intervention, and that the system administrator can
do nothing about. Patch below reduces the severity of these messages to
debug.
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Dave Jones <davej@redhat.com>
Peter Chubb [Tue, 31 May 2005 21:39:30 +0000 (14:39 -0700)]
[PATCH] pcdp.c build fix
In file included from drivers/firmware/pcdp.c:18:
drivers/firmware/pcdp.h:48: error: field `addr' has incomplete type
drivers/firmware/pcdp.c: In function `setup_serial_console':
drivers/firmware/pcdp.c:27: error: `ACPI_ADR_SPACE_SYSTEM_MEMORY' undeclared (first use in this function)
Cc: <tony.luck@intel.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Roman Zippel [Tue, 31 May 2005 21:39:29 +0000 (14:39 -0700)]
[PATCH] flush icache in correct context
flush_icache_range() is used in two different situation - in binfmt_elf.c &
co for user space mappings and module.c for kernel modules. On m68k
flush_icache_range() doesn't know which data to flush, as it has separate
address spaces and the pointer argument can be valid in either address
space.
First I considered splitting flush_icache_range(), but this patch is
simpler. Setting the correct context gives flush_icache_range() enough
information to flush the correct data.
Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jens Axboe [Tue, 31 May 2005 15:47:36 +0000 (17:47 +0200)]
[PATCH] Relax idecd dma alignment check
Only the address needs alignment of mask bits, length should work with
a relaxed alignment check.
Signed-off-by: Jens Axboe <axboe@suse.de>
[ This is take 2: make the length check be for 16-byte alignment, not
just word alignment. That should hopefully keep everybody happy,
while still allowing CD writing with DMA ]
When I sent in the patch adding the code for the kernel to tell the
firmware about its capabilities on pSeries machines, I included the
function to give the capabilities to firmware but somehow forgot the
hunk that adds the call to the new function. This patch adds the
call.
Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Michael Ellerman [Mon, 30 May 2005 03:24:30 +0000 (20:24 -0700)]
[NET]: Add is_multicast_ether_addr() in include/linux/etherdevice.h
This patch adds is_multicast_ether_addr() to go along with
is_valid_ether_addr() and friends. It then changes
is_valid_ether_addr() to use the new macro, and fixes up the comment
on that function to move implementation details out of the API doco.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Harald Welte [Mon, 30 May 2005 03:23:46 +0000 (20:23 -0700)]
[IPV4]: Primary and secondary addresses
Add an option to make secondary IP addresses get promoted
when primary IP addresses are removed from the device.
It defaults to off to preserve existing behavior.
Signed-off-by: Harald Welte <laforge@gnumonks.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Sun, 29 May 2005 21:59:49 +0000 (14:59 -0700)]
[TG3]: Fix bug in tg3_load_firmware_cpu
Add tg3_nvram_lock() and tg3_nvram_unlock() calls around tg3_halt_cpu().
It is possible that the bootcode may be loading code from nvram during
this call and stopping the cpu without getting the lock may cause
uncompleted nvram data to be left in the nvram data register. Subsequent
calls to read/write nvram data will fail.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This improves the bridge local receive path by avoiding going
through another softirq. The bridge receive path is already being called
from a netif_receive_skb() there is no point in going through another
receiveq round trip.
Recursion is limited because bridge can never be a port of a bridge
so handle_bridge() always returns.
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid poisoning of the bridge forwarding table by frames that have been
dropped by filtering. This prevents spoofed source addresses on hostile
side of bridge from causing packet leakage, a small but possible security
risk.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Make features of the bridge pseudo-device be a subset of the underlying
devices. Motivated by Xen and others who use bridging to do failover.
Signed-off-by: Catalin BOIE <catab at umrella.ro> Signed-off-by: Stephen Hemminger <shemminger@osdl.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Resend of earlier patch (no changes) from Catalin used to provide
device feature change notification.
Signed-off-by: Catalin BOIE <catab at umbrella.ro> Acked-by: Stephen Hemminger <shemminger@osdl.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Kumar Gala [Sat, 28 May 2005 22:52:14 +0000 (15:52 -0700)]
[PATCH] ppc32: MPC834x BCSR_SIZE too small for use in a BAT.
The call to io_block_mapping was creating an invalid BAT entry because the
value of BCSR_SIZE (32K) is too small to be used in a BAT (128K min). This
change removes the io_block_mapping call since these registers can easily
be mapped using ioremap at the point of use.
Signed-off-by: Randy Vinson <rvinson@mvista.com> Signed-off-by: Kumar Gala <kumar.gala@freescale.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The error checking for emulation of load string instructions was overly
generous and would cause certain valid forms of the instructions to be
treated as illegal. We drop the range checking since the architecture
allows this to be boundedly undefined. Tests on CPUs that support these
instructions appear not do cause illegal instruction traps on range errors
and just allow the execution to occur.
Thanks to Kim Phillips for debugging this and figuring out what real HW was
doing.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Vitaly Bordug [Sat, 28 May 2005 22:52:09 +0000 (15:52 -0700)]
[PATCH] ppc32: Support for 82xx PQII on-chip PCI bridge
This patch adds on-chip PCI bridge support for the PQ2 family. The
incomplete existent code is updated with interrupt handling stuff and
board-specific bits for 8272ADS and PQ2FADS; the related files were renamed
(from m8260_pci to m82xx_pci) to be of more generic fashion. This is
tested with 8266ADS and 8272ADS, should work on PQ2FADS as well.
Kumar Gala [Sat, 28 May 2005 22:52:07 +0000 (15:52 -0700)]
[PATCH] ppc32: Add VIA IDE support to MPC8555 CDS platform
Add support for the VIA IDE controller that exists on the MPC8555 CDS
system. Updated the config for the system to enable support by default.
Signed-off-by: Scott Hall <shall@mvista.com> Signed-off-by: Kumar Gala <kumar.gala@freescale.com> Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Kumar Gala [Sat, 28 May 2005 22:52:06 +0000 (15:52 -0700)]
[PATCH] ppc32: Fix some minor issues related to FSL Book-E KGDB support
Some debug registers needed to be initialized early on to allow proper
support for KGDB. Additionally, we need to setup the
ppc.md_early_serial_map function pointer on boards that have serial support
for KGDB.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Kumar Gala [Sat, 28 May 2005 22:52:05 +0000 (15:52 -0700)]
[PATCH] ppc32: Fix uImage make target to report success correctly
The existing make rule when building a uImage would check to see if the
image file existed to report 'is ready' or 'not made'. However make
appeared to compute the file list before the rule was executed.
Signed-off-by: Chris Clark <cpclark@xmission.com> Signed-off-by: Kumar Gala <kumar.gala@freescale.com> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This var is currently useless, as it's apparent from reading the code. Until
2.6.11 it was used in some code related to jail mode, in the same proc.:
if(jail){
while(!reading) sched_yield();
}
jail mode has been dropped, together with that use, so let's finish dropping
this.
Also, remove some other useless definitions I met.
Acked-by: Jeff Dike <jdike@addtoit.com> Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix it a bit (after some cross checking with "man arch_prctl"). There were:
*) typos FS/GS and back
*) FS in place of FS_BASE (and the same for GS)
*) the procedure used put_user on &addr, where addr was the parameter (i.e.
changed its param with put_user, completely useless) rather than interpreting
addr as a pointer, as requested in this case (see the man page).
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
, I've also added a warning which should refuse compilation with insane values
for PREEMPT_ACTIVE... maybe we should simply move PREEMPT_ACTIVE out of
architectures using GENERIC_IRQS.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Paul Mundt [Sat, 28 May 2005 22:52:01 +0000 (15:52 -0700)]
[PATCH] sh: PREEMPT_ACTIVE fix
Port Paulus's ppc64 fix to sh:
When the generic IRQ stuff went in, it seems that HARDIRQ_BITS got bumped
from 9 (for ppc64) up to 12. Consequently, the PREEMPT_ACTIVE bit is now
within HARDIRQ_MASK, and I get in_interrupt() falsely returning true when
PREEMPT_ACTIVE is set, and thus a BUG_ON tripping in arch/ppc64/mm/tlb.c.
Signed-off-by: Paul Mundt <lethal@linux-sh.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] uml: split CONFIG_FRAME_POINTER from DEBUG_INFO
Until now, FRAME_POINTER was set = DEBUG_INFO for UML. Change it to be the
default way, so that it can be enabled alone (for instance to get better
backtraces on crashes). The call-trace dumper which uses the frame pointer is
not yet in, I'm going to introduce it in a separate patch.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a MODULE_LICENSE("GPL") to the driver, remove some unused macros and add
the GPL license (it's GPL-licensed anyway since it's a GPL-derivative, apart
that Jeff Dike releases GPL software, in case anybody is wondering).
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jeff Dike [Sat, 28 May 2005 22:51:54 +0000 (15:51 -0700)]
[PATCH] uml: remove 2_5compat.h
Remove old useless header that was used in Ye Olde Times during 2.4->2.5
porting to abstract differences. It's definitions are no more used anyway, so
let's finally kill it.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Jeff Dike <jdike@addtoit.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Manu Abraham [Sat, 28 May 2005 22:51:52 +0000 (15:51 -0700)]
[PATCH] dvb: Small cleanup
Miscellaneous cleanup
Signed-off-by: Manu Abraham <manu@kromtek.com> Cc: Johannes Stezenbach <js@linuxtv.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Manu Abraham [Sat, 28 May 2005 22:51:51 +0000 (15:51 -0700)]
[PATCH] dvb: Fix 22k tone control
Signed-off-by: Manu Abraham <manu@kromtek.com> Cc: Johannes Stezenbach <js@linuxtv.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Manu Abraham [Sat, 28 May 2005 22:51:51 +0000 (15:51 -0700)]
[PATCH] dvb: Fix LNB power switching
Signed-off-by: Manu Abraham <manu@kromtek.com> Cc: Johannes Stezenbach <js@linuxtv.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Manu Abraham [Sat, 28 May 2005 22:51:50 +0000 (15:51 -0700)]
[PATCH] dvb: Remove unnecessary casts
Cleanup unnecessary (and undesirable) casts, demodulator_priv is already a
void*. Suggestion from Andrew Morton
Signed-off-by: Manu Abraham <manu@kromtek.com> Cc: Johannes Stezenbach <js@linuxtv.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Manu Abraham [Sat, 28 May 2005 22:51:48 +0000 (15:51 -0700)]
[PATCH] dvb: Fix Mini DiSEqC bug
The bug was visible as a warning with gcc-3.4.4 (prerelease)
Message:
drivers/media/dvb/bt8xx/dst.c:1349: warning: initialization from
incompatible pointer type.
Signed-off-by: Manu Abraham <manu@kromtek.com> Cc: Johannes Stezenbach <js@linuxtv.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patrick McManus [Sat, 28 May 2005 22:51:46 +0000 (15:51 -0700)]
[PATCH] intelfb section fix
On Nov 16 2004 a change to intelfbdrv.c was commited (as part of 0.9.2 it
looks like) that added __initdata to all of the module param variables that
seems to create the opportunity for an oops.
I've recently been chasing an OOPS
(http://marc.theaimsgroup.com/?l=linux-kernel&m=111552250920370&w=2) I
created by reading every file on the /sys file system and I've traced it
back to this code in the intelfbdrv. Though I had root privs in my initial
problem report, it turns out they are un-necessary to generate the oops -
all you've got to do is "cat /sys/module/intelfb/parameters/mode" enough
times and eventually it will oops.
This is because sysfs automatically exports all module_param declarations
to the sysfs file system.. which means those variables can be dynamically
evaluated at any later time, which of course means marking them __initdata
is a bad idea ;).. when they happen to be char *'s it is an especially bad
idea ;).
Applying the patch below clears up the OOPS for me.
Signed-off-by: Patrick McManus <mcmanus@ducksong.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Pavel Machek [Fri, 27 May 2005 19:53:03 +0000 (12:53 -0700)]
[PATCH] fix jumpy mouse cursor on console
Do not send empty events to gpm. (Keyboards are assumed to have scroll
wheel these days, that makes them part-mouse. That means typing on
keyboard generates empty mouse events).
From: Dmitry Torokhov <dtor_core@ameritech.net> Signed-off-by: Pavel Machek <pavel@suse.cz> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Recent kernels occasionally trigger a PMU timeout on some mac laptops,
typically on wakeup from sleep. This seem to be caused by either a too big
latency caused by the cpufreq switch on wakeup from sleep or by an
interrupt beeing lost due to the reset of the interrupt controller done
during wakeup.
This patch makes that code more robust by stopping PMU auto poll activity
around cpufreq changes on machines that use the PMU for such changes (long
latency switching involving a CPU hard reset and flush of all caches) and
by removing the reset of the open pic interrupt controller on wakeup (that
can cause the loss of an interrupt and Darwin doesn't do it, so it must not
be necessary).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Siddha, Suresh B [Fri, 27 May 2005 19:53:01 +0000 (12:53 -0700)]
[PATCH] x86: fix smp_num_siblings on buggy BIOSes
This fixes 'smp_num_siblings' value on the systems with a buggy bios,
which sets number of siblings to '2' even when HT is disabled. (more
details are at http://bugzilla.kernel.org/show_bug.cgi?id=4359)
I am planning to do more cleanup in this area (like moving smp_num_siblings
to per cpuinfo) shortly.
John Hawkes [Fri, 27 May 2005 19:53:00 +0000 (12:53 -0700)]
[PATCH] drop note_interrupt() for per-CPU for proper scaling
The "unhandled interrupts" catcher, note_interrupt(), increments a global
desc->irq_count and grossly damages scaling of very large systems, e.g.,
>192p ia64 Altix, because of this highly contented cacheline, especially
for timer interrupts. 384p is severely crippled, and 512p is unuseable.
All calls to note_interrupt() can be disabled by booting with "noirqdebug",
but this disables the useful interrupt checking for all interrupts.
I propose eliminating note_interrupt() for all per-CPU interrupts. This
was the behavior of linux-2.6.10 and earlier, but in 2.6.11 a code
restructuring added a call to note_interrupt() for per-CPU interrupts.
Besides, note_interrupt() is a bit racy for concurrent CPU calls anyway, as
the desc->irq_count++ increment isn't atomic (which, if done, would make
scaling even worse).
Signed-off-by: John Hawkes <hawkes@sgi.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Stephen Rothwell [Fri, 27 May 2005 19:52:58 +0000 (12:52 -0700)]
[PATCH] ppc64 iSeries: make virtual DVD-RAMs writable again
It appears that another test has been added in the Uniform CDROM layer that
must be passed before a DVD-RAM is considered writeable. This patch
implements an emulation of the needed packet command for the viocd driver.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] ppc32: Fix Alsa PowerMac driver on old machines
The g5 support code broke some earlier models unfortunately as those bail
out early from the detect function, before the point where I added the code
to locate the PCI device for use with DMA allocations.
This patch fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds a missing attribute to pmac cpufreq so that
"scaling_available_frequencies" works. It also cleans up the duplicate
definitions for low and high speed constants.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: John Clemens <clemej@alum.rpi.edu> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Dmitry Torokhov [Sat, 28 May 2005 07:12:05 +0000 (02:12 -0500)]
Input: automatically disable MUX mode on Toshiba Satellite P10
because it interferes with ALPS touchpad detection and
causes horrible death on reboot. Since P10 does not have
external PS/2 ports MUX mode does not have any advantages
over legacy mode anyway.
projects / linux-2.6 / log