From: Andrew Victor Date: Wed, 27 Sep 2006 12:23:00 +0000 (+0100) Subject: [ARM] 3867/1: AT91 GPIO update X-Git-Tag: v2.6.19-rc1~885^2~9 X-Git-Url: https://err.no/cgi-bin/gitweb.cgi?a=commitdiff_plain;h=f21738341ca330ec83ef978ee63ffa5ecf13f082;p=linux-2.6 [ARM] 3867/1: AT91 GPIO update This patch makes the AT91 gpio.c support processor-generic (AT91RM9200 and AT91SAM9xxx). The GPIO controllers supported by a particular AT91 processor are defined in the processor-specific file and are registered with gpio.c at startup. Signed-off-by: Andrew Victor Signed-off-by: Russell King --- diff --git a/arch/arm/mach-at91rm9200/at91rm9200.c b/arch/arm/mach-at91rm9200/at91rm9200.c index ae04cbdf0b..c32d0c996f 100644 --- a/arch/arm/mach-at91rm9200/at91rm9200.c +++ b/arch/arm/mach-at91rm9200/at91rm9200.c @@ -243,11 +243,34 @@ static void __init at91rm9200_register_clocks(void) clk_register(&pck3); } +/* -------------------------------------------------------------------- + * GPIO + * -------------------------------------------------------------------- */ + +static struct at91_gpio_bank at91rm9200_gpio[] = { + { + .id = AT91RM9200_ID_PIOA, + .offset = AT91_PIOA, + .clock = &pioA_clk, + }, { + .id = AT91RM9200_ID_PIOB, + .offset = AT91_PIOB, + .clock = &pioB_clk, + }, { + .id = AT91RM9200_ID_PIOC, + .offset = AT91_PIOC, + .clock = &pioC_clk, + }, { + .id = AT91RM9200_ID_PIOD, + .offset = AT91_PIOD, + .clock = &pioD_clk, + } +}; /* -------------------------------------------------------------------- * AT91RM9200 processor initialization * -------------------------------------------------------------------- */ -void __init at91rm9200_initialize(unsigned long main_clock) +void __init at91rm9200_initialize(unsigned long main_clock, unsigned short banks) { /* Map peripherals */ iotable_init(at91rm9200_io_desc, ARRAY_SIZE(at91rm9200_io_desc)); @@ -257,8 +280,16 @@ void __init at91rm9200_initialize(unsigned long main_clock) /* Register the processor-specific clocks */ at91rm9200_register_clocks(); + + /* Initialize GPIO subsystem */ + at91_gpio_init(at91rm9200_gpio, banks); } + +/* -------------------------------------------------------------------- + * Interrupt initialization + * -------------------------------------------------------------------- */ + /* * The default interrupt priority levels (0 = lowest, 7 = highest). */ @@ -297,10 +328,14 @@ static unsigned int at91rm9200_default_irq_priority[NR_AIC_IRQS] __initdata = { 0 /* Advanced Interrupt Controller (IRQ6) */ }; -void __init at91rm9200_init_irq(unsigned int priority[NR_AIC_IRQS]) +void __init at91rm9200_init_interrupts(unsigned int priority[NR_AIC_IRQS]) { if (!priority) priority = at91rm9200_default_irq_priority; + /* Initialize the AIC interrupt controller */ at91_aic_init(priority); + + /* Enable GPIO interrupts */ + at91_gpio_irq_setup(); } diff --git a/arch/arm/mach-at91rm9200/board-1arm.c b/arch/arm/mach-at91rm9200/board-1arm.c index d2aa9c4a8b..36eecd7161 100644 --- a/arch/arm/mach-at91rm9200/board-1arm.c +++ b/arch/arm/mach-at91rm9200/board-1arm.c @@ -39,14 +39,6 @@ #include "generic.h" -static void __init onearm_init_irq(void) -{ - /* Initialize AIC controller */ - at91rm9200_init_irq(NULL); - - /* Set up the GPIO interrupts */ - at91_gpio_irq_setup(PQFP_GPIO_BANKS); -} /* * Serial port configuration. @@ -62,12 +54,17 @@ static struct at91_uart_config __initdata onearm_uart_config = { static void __init onearm_map_io(void) { /* Initialize processor: 18.432 MHz crystal */ - at91rm9200_initialize(18432000); + at91rm9200_initialize(18432000, AT91RM9200_PQFP); /* Setup the serial ports and console */ at91_init_serial(&onearm_uart_config); } +static void __init onearm_init_irq(void) +{ + at91rm9200_init_interrupts(NULL); +} + static struct at91_eth_data __initdata onearm_eth_data = { .phy_irq_pin = AT91_PIN_PC4, .is_rmii = 1, diff --git a/arch/arm/mach-at91rm9200/board-carmeva.c b/arch/arm/mach-at91rm9200/board-carmeva.c index 6af252bcb0..50e513681a 100644 --- a/arch/arm/mach-at91rm9200/board-carmeva.c +++ b/arch/arm/mach-at91rm9200/board-carmeva.c @@ -40,14 +40,6 @@ #include "generic.h" -static void __init carmeva_init_irq(void) -{ - /* Initialize AIC controller */ - at91rm9200_init_irq(NULL); - - /* Set up the GPIO interrupts */ - at91_gpio_irq_setup(BGA_GPIO_BANKS); -} /* * Serial port configuration. @@ -63,12 +55,18 @@ static struct at91_uart_config __initdata carmeva_uart_config = { static void __init carmeva_map_io(void) { /* Initialize processor: 20.000 MHz crystal */ - at91rm9200_initialize(20000000); + at91rm9200_initialize(20000000, AT91RM9200_BGA); /* Setup the serial ports and console */ at91_init_serial(&carmeva_uart_config); } +static void __init carmeva_init_irq(void) +{ + at91rm9200_init_interrupts(NULL); +} + + static struct at91_eth_data __initdata carmeva_eth_data = { .phy_irq_pin = AT91_PIN_PC4, .is_rmii = 1, diff --git a/arch/arm/mach-at91rm9200/board-csb337.c b/arch/arm/mach-at91rm9200/board-csb337.c index f74b483329..8eeae491ce 100644 --- a/arch/arm/mach-at91rm9200/board-csb337.c +++ b/arch/arm/mach-at91rm9200/board-csb337.c @@ -39,14 +39,6 @@ #include "generic.h" -static void __init csb337_init_irq(void) -{ - /* Initialize AIC controller */ - at91rm9200_init_irq(NULL); - - /* Set up the GPIO interrupts */ - at91_gpio_irq_setup(BGA_GPIO_BANKS); -} /* * Serial port configuration. @@ -62,7 +54,7 @@ static struct at91_uart_config __initdata csb337_uart_config = { static void __init csb337_map_io(void) { /* Initialize processor: 3.6864 MHz crystal */ - at91rm9200_initialize(3686400); + at91rm9200_initialize(3686400, AT91RM9200_BGA); /* Setup the LEDs */ at91_init_leds(AT91_PIN_PB0, AT91_PIN_PB1); @@ -71,6 +63,11 @@ static void __init csb337_map_io(void) at91_init_serial(&csb337_uart_config); } +static void __init csb337_init_irq(void) +{ + at91rm9200_init_interrupts(NULL); +} + static struct at91_eth_data __initdata csb337_eth_data = { .phy_irq_pin = AT91_PIN_PC2, .is_rmii = 0, diff --git a/arch/arm/mach-at91rm9200/board-csb637.c b/arch/arm/mach-at91rm9200/board-csb637.c index 880350997a..a29fa0e822 100644 --- a/arch/arm/mach-at91rm9200/board-csb637.c +++ b/arch/arm/mach-at91rm9200/board-csb637.c @@ -38,14 +38,6 @@ #include "generic.h" -static void __init csb637_init_irq(void) -{ - /* Initialize AIC controller */ - at91rm9200_init_irq(NULL); - - /* Set up the GPIO interrupts */ - at91_gpio_irq_setup(BGA_GPIO_BANKS); -} /* * Serial port configuration. @@ -61,7 +53,7 @@ static struct at91_uart_config __initdata csb637_uart_config = { static void __init csb637_map_io(void) { /* Initialize processor: 3.6864 MHz crystal */ - at91rm9200_initialize(3686400); + at91rm9200_initialize(3686400, AT91RM9200_BGA); /* Setup the LEDs */ at91_init_leds(AT91_PIN_PB2, AT91_PIN_PB2); @@ -70,6 +62,11 @@ static void __init csb637_map_io(void) at91_init_serial(&csb637_uart_config); } +static void __init csb637_init_irq(void) +{ + at91rm9200_init_interrupts(NULL); +} + static struct at91_eth_data __initdata csb637_eth_data = { .phy_irq_pin = AT91_PIN_PC0, .is_rmii = 0, diff --git a/arch/arm/mach-at91rm9200/board-dk.c b/arch/arm/mach-at91rm9200/board-dk.c index 23ea9d63b9..54c32d00b6 100644 --- a/arch/arm/mach-at91rm9200/board-dk.c +++ b/arch/arm/mach-at91rm9200/board-dk.c @@ -42,14 +42,6 @@ #include "generic.h" -static void __init dk_init_irq(void) -{ - /* Initialize AIC controller */ - at91rm9200_init_irq(NULL); - - /* Set up the GPIO interrupts */ - at91_gpio_irq_setup(BGA_GPIO_BANKS); -} /* * Serial port configuration. @@ -65,7 +57,7 @@ static struct at91_uart_config __initdata dk_uart_config = { static void __init dk_map_io(void) { /* Initialize processor: 18.432 MHz crystal */ - at91rm9200_initialize(18432000); + at91rm9200_initialize(18432000, AT91RM9200_BGA); /* Setup the LEDs */ at91_init_leds(AT91_PIN_PB2, AT91_PIN_PB2); @@ -74,6 +66,11 @@ static void __init dk_map_io(void) at91_init_serial(&dk_uart_config); } +static void __init dk_init_irq(void) +{ + at91rm9200_init_interrupts(NULL); +} + static struct at91_eth_data __initdata dk_eth_data = { .phy_irq_pin = AT91_PIN_PC4, .is_rmii = 1, diff --git a/arch/arm/mach-at91rm9200/board-eb9200.c b/arch/arm/mach-at91rm9200/board-eb9200.c index 2ceb267585..c6e0d51fbe 100644 --- a/arch/arm/mach-at91rm9200/board-eb9200.c +++ b/arch/arm/mach-at91rm9200/board-eb9200.c @@ -40,14 +40,6 @@ #include "generic.h" -static void __init eb9200_init_irq(void) -{ - /* Initialize AIC controller */ - at91rm9200_init_irq(NULL); - - /* Set up the GPIO interrupts */ - at91_gpio_irq_setup(BGA_GPIO_BANKS); -} /* * Serial port configuration. @@ -63,12 +55,17 @@ static struct at91_uart_config __initdata eb9200_uart_config = { static void __init eb9200_map_io(void) { /* Initialize processor: 18.432 MHz crystal */ - at91rm9200_initialize(18432000); + at91rm9200_initialize(18432000, AT91RM9200_BGA); /* Setup the serial ports and console */ at91_init_serial(&eb9200_uart_config); } +static void __init eb9200_init_irq(void) +{ + at91rm9200_init_interrupts(NULL); +} + static struct at91_eth_data __initdata eb9200_eth_data = { .phy_irq_pin = AT91_PIN_PC4, .is_rmii = 1, diff --git a/arch/arm/mach-at91rm9200/board-ek.c b/arch/arm/mach-at91rm9200/board-ek.c index 8cd83364cd..830eb79321 100644 --- a/arch/arm/mach-at91rm9200/board-ek.c +++ b/arch/arm/mach-at91rm9200/board-ek.c @@ -42,14 +42,6 @@ #include "generic.h" -static void __init ek_init_irq(void) -{ - /* Initialize AIC controller */ - at91rm9200_init_irq(NULL); - - /* Set up the GPIO interrupts */ - at91_gpio_irq_setup(BGA_GPIO_BANKS); -} /* * Serial port configuration. @@ -65,7 +57,7 @@ static struct at91_uart_config __initdata ek_uart_config = { static void __init ek_map_io(void) { /* Initialize processor: 18.432 MHz crystal */ - at91rm9200_initialize(18432000); + at91rm9200_initialize(18432000, AT91RM9200_BGA); /* Setup the LEDs */ at91_init_leds(AT91_PIN_PB1, AT91_PIN_PB2); @@ -74,6 +66,11 @@ static void __init ek_map_io(void) at91_init_serial(&ek_uart_config); } +static void __init ek_init_irq(void) +{ + at91rm9200_init_interrupts(NULL); +} + static struct at91_eth_data __initdata ek_eth_data = { .phy_irq_pin = AT91_PIN_PC4, .is_rmii = 1, diff --git a/arch/arm/mach-at91rm9200/board-kafa.c b/arch/arm/mach-at91rm9200/board-kafa.c index d9a6b7e7d6..91e301924f 100644 --- a/arch/arm/mach-at91rm9200/board-kafa.c +++ b/arch/arm/mach-at91rm9200/board-kafa.c @@ -39,14 +39,6 @@ #include "generic.h" -static void __init kafa_init_irq(void) -{ - /* Initialize AIC controller */ - at91rm9200_init_irq(NULL); - - /* Set up the GPIO interrupts */ - at91_gpio_irq_setup(PQFP_GPIO_BANKS); -} /* * Serial port configuration. @@ -62,7 +54,7 @@ static struct at91_uart_config __initdata kafa_uart_config = { static void __init kafa_map_io(void) { /* Initialize processor: 18.432 MHz crystal */ - at91rm9200_initialize(18432000); + at91rm9200_initialize(18432000, AT91RM9200_PQFP); /* Set up the LEDs */ at91_init_leds(AT91_PIN_PB4, AT91_PIN_PB4); @@ -71,6 +63,11 @@ static void __init kafa_map_io(void) at91_init_serial(&kafa_uart_config); } +static void __init kafa_init_irq(void) +{ + at91rm9200_init_interrupts(NULL); +} + static struct at91_eth_data __initdata kafa_eth_data = { .phy_irq_pin = AT91_PIN_PC4, .is_rmii = 0, diff --git a/arch/arm/mach-at91rm9200/board-kb9202.c b/arch/arm/mach-at91rm9200/board-kb9202.c index 935238ffa3..55b08f9b95 100644 --- a/arch/arm/mach-at91rm9200/board-kb9202.c +++ b/arch/arm/mach-at91rm9200/board-kb9202.c @@ -40,14 +40,6 @@ #include "generic.h" -static void __init kb9202_init_irq(void) -{ - /* Initialize AIC controller */ - at91rm9200_init_irq(NULL); - - /* Set up the GPIO interrupts */ - at91_gpio_irq_setup(PQFP_GPIO_BANKS); -} /* * Serial port configuration. @@ -63,7 +55,7 @@ static struct at91_uart_config __initdata kb9202_uart_config = { static void __init kb9202_map_io(void) { /* Initialize processor: 10 MHz crystal */ - at91rm9200_initialize(10000000); + at91rm9200_initialize(10000000, AT91RM9200_PQFP); /* Set up the LEDs */ at91_init_leds(AT91_PIN_PC19, AT91_PIN_PC18); @@ -72,6 +64,11 @@ static void __init kb9202_map_io(void) at91_init_serial(&kb9202_uart_config); } +static void __init kb9202_init_irq(void) +{ + at91rm9200_init_interrupts(NULL); +} + static struct at91_eth_data __initdata kb9202_eth_data = { .phy_irq_pin = AT91_PIN_PB29, .is_rmii = 0, diff --git a/arch/arm/mach-at91rm9200/generic.h b/arch/arm/mach-at91rm9200/generic.h index c44e0e0746..694e411e28 100644 --- a/arch/arm/mach-at91rm9200/generic.h +++ b/arch/arm/mach-at91rm9200/generic.h @@ -9,12 +9,11 @@ */ /* Processors */ -extern void __init at91rm9200_initialize(unsigned long main_clock); +extern void __init at91rm9200_initialize(unsigned long main_clock, unsigned short banks); /* Interrupts */ -extern void __init at91rm9200_init_irq(unsigned int priority[]); +extern void __init at91rm9200_init_interrupts(unsigned int priority[]); extern void __init at91_aic_init(unsigned int priority[]); -extern void __init at91_gpio_irq_setup(unsigned banks); /* Timer */ struct sys_timer; @@ -29,3 +28,14 @@ extern void __init at91_clock_associate(const char *id, struct device *dev, cons extern void at91_irq_suspend(void); extern void at91_irq_resume(void); + /* GPIO */ +#define AT91RM9200_PQFP 3 /* AT91RM9200 PQFP package has 3 banks */ +#define AT91RM9200_BGA 4 /* AT91RM9200 BGA package has 4 banks */ + +struct at91_gpio_bank { + unsigned short id; /* peripheral ID */ + unsigned long offset; /* offset from system peripheral base */ + struct clk *clock; /* associated clock */ +}; +extern void __init at91_gpio_init(struct at91_gpio_bank *, int nr_banks); +extern void __init at91_gpio_irq_setup(void); diff --git a/arch/arm/mach-at91rm9200/gpio.c b/arch/arm/mach-at91rm9200/gpio.c index 8476cb8856..58c9bf5e95 100644 --- a/arch/arm/mach-at91rm9200/gpio.c +++ b/arch/arm/mach-at91rm9200/gpio.c @@ -9,6 +9,7 @@ * (at your option) any later version. */ +#include #include #include #include @@ -20,12 +21,12 @@ #include #include -static const u32 pio_controller_offset[4] = { - AT91_PIOA, - AT91_PIOB, - AT91_PIOC, - AT91_PIOD, -}; +#include "generic.h" + + +static struct at91_gpio_bank *gpio; +static int gpio_banks; + static inline void __iomem *pin_to_controller(unsigned pin) { @@ -33,8 +34,8 @@ static inline void __iomem *pin_to_controller(unsigned pin) pin -= PIN_BASE; pin /= 32; - if (likely(pin < BGA_GPIO_BANKS)) - return sys_base + pio_controller_offset[pin]; + if (likely(pin < gpio_banks)) + return sys_base + gpio[pin].offset; return NULL; } @@ -179,7 +180,6 @@ EXPORT_SYMBOL(at91_set_multi_drive); /*--------------------------------------------------------------------------*/ - /* * assuming the pin is muxed as a gpio output, set its value. */ @@ -216,8 +216,8 @@ EXPORT_SYMBOL(at91_get_gpio_value); #ifdef CONFIG_PM -static u32 wakeups[BGA_GPIO_BANKS]; -static u32 backups[BGA_GPIO_BANKS]; +static u32 wakeups[MAX_GPIO_BANKS]; +static u32 backups[MAX_GPIO_BANKS]; static int gpio_irq_set_wake(unsigned pin, unsigned state) { @@ -226,7 +226,7 @@ static int gpio_irq_set_wake(unsigned pin, unsigned state) pin -= PIN_BASE; pin /= 32; - if (unlikely(pin >= BGA_GPIO_BANKS)) + if (unlikely(pin >= MAX_GPIO_BANKS)) return -EINVAL; if (state) @@ -241,8 +241,8 @@ void at91_gpio_suspend(void) { int i; - for (i = 0; i < BGA_GPIO_BANKS; i++) { - u32 pio = pio_controller_offset[i]; + for (i = 0; i < gpio_banks; i++) { + u32 pio = gpio[i].offset; /* * Note: drivers should have disabled GPIO interrupts that @@ -257,14 +257,14 @@ void at91_gpio_suspend(void) * first place! */ backups[i] = at91_sys_read(pio + PIO_IMR); - at91_sys_write(pio_controller_offset[i] + PIO_IDR, backups[i]); - at91_sys_write(pio_controller_offset[i] + PIO_IER, wakeups[i]); + at91_sys_write(pio + PIO_IDR, backups[i]); + at91_sys_write(pio + PIO_IER, wakeups[i]); if (!wakeups[i]) { - disable_irq_wake(AT91RM9200_ID_PIOA + i); - at91_sys_write(AT91_PMC_PCDR, 1 << (AT91RM9200_ID_PIOA + i)); + disable_irq_wake(gpio[i].id); + at91_sys_write(AT91_PMC_PCDR, 1 << gpio[i].id); } else { - enable_irq_wake(AT91RM9200_ID_PIOA + i); + enable_irq_wake(gpio[i].id); #ifdef CONFIG_PM_DEBUG printk(KERN_DEBUG "GPIO-%c may wake for %08x\n", "ABCD"[i], wakeups[i]); #endif @@ -276,16 +276,13 @@ void at91_gpio_resume(void) { int i; - for (i = 0; i < BGA_GPIO_BANKS; i++) { - at91_sys_write(pio_controller_offset[i] + PIO_IDR, wakeups[i]); - at91_sys_write(pio_controller_offset[i] + PIO_IER, backups[i]); - } + for (i = 0; i < gpio_banks; i++) { + u32 pio = gpio[i].offset; - at91_sys_write(AT91_PMC_PCER, - (1 << AT91RM9200_ID_PIOA) - | (1 << AT91RM9200_ID_PIOB) - | (1 << AT91RM9200_ID_PIOC) - | (1 << AT91RM9200_ID_PIOD)); + at91_sys_write(pio + PIO_IDR, wakeups[i]); + at91_sys_write(pio + PIO_IER, backups[i]); + at91_sys_write(AT91_PMC_PCER, 1 << gpio[i].id); + } } #else @@ -377,20 +374,25 @@ static void gpio_irq_handler(unsigned irq, struct irqdesc *desc, struct pt_regs /* now it may re-trigger */ } -/* call this from board-specific init_irq */ -void __init at91_gpio_irq_setup(unsigned banks) +/*--------------------------------------------------------------------------*/ + +/* + * Called from the processor-specific init to enable GPIO interrupt support. + */ +void __init at91_gpio_irq_setup(void) { - unsigned pioc, pin, id; + unsigned pioc, pin; - if (banks > 4) - banks = 4; - for (pioc = 0, pin = PIN_BASE, id = AT91RM9200_ID_PIOA; - pioc < banks; - pioc++, id++) { + for (pioc = 0, pin = PIN_BASE; + pioc < gpio_banks; + pioc++) { void __iomem *controller; + unsigned id = gpio[pioc].id; unsigned i; - controller = (void __iomem *) AT91_VA_BASE_SYS + pio_controller_offset[pioc]; + clk_enable(gpio[pioc].clock); /* enable PIO controller's clock */ + + controller = (void __iomem *) AT91_VA_BASE_SYS + gpio[pioc].offset; __raw_writel(~0, controller + PIO_IDR); set_irq_data(id, (void *) pin); @@ -408,5 +410,16 @@ void __init at91_gpio_irq_setup(unsigned banks) set_irq_chained_handler(id, gpio_irq_handler); } - pr_info("AT91: %d gpio irqs in %d banks\n", pin - PIN_BASE, banks); + pr_info("AT91: %d gpio irqs in %d banks\n", pin - PIN_BASE, gpio_banks); +} + +/* + * Called from the processor-specific init to enable GPIO pin support. + */ +void __init at91_gpio_init(struct at91_gpio_bank *data, int nr_banks) +{ + BUG_ON(nr_banks > MAX_GPIO_BANKS); + + gpio = data; + gpio_banks = nr_banks; } diff --git a/arch/arm/mach-at91rm9200/irq.c b/arch/arm/mach-at91rm9200/irq.c index 8cd60a99c5..3e488117ca 100644 --- a/arch/arm/mach-at91rm9200/irq.c +++ b/arch/arm/mach-at91rm9200/irq.c @@ -34,8 +34,6 @@ #include #include -#include "generic.h" - static void at91_aic_mask_irq(unsigned int irq) { diff --git a/include/asm-arm/arch-at91rm9200/gpio.h b/include/asm-arm/arch-at91rm9200/gpio.h index 6243f28a0b..a011d27876 100644 --- a/include/asm-arm/arch-at91rm9200/gpio.h +++ b/include/asm-arm/arch-at91rm9200/gpio.h @@ -17,8 +17,7 @@ #define PIN_BASE NR_AIC_IRQS -#define PQFP_GPIO_BANKS 3 /* PQFP package has 3 banks */ -#define BGA_GPIO_BANKS 4 /* BGA package has 4 banks */ +#define MAX_GPIO_BANKS 4 /* these pin numbers double as IRQ numbers, like AT91xxx_ID_* values */ @@ -180,17 +179,18 @@ #ifndef __ASSEMBLY__ /* setup setup routines, called from board init or driver probe() */ -extern int at91_set_A_periph(unsigned pin, int use_pullup); -extern int at91_set_B_periph(unsigned pin, int use_pullup); -extern int at91_set_gpio_input(unsigned pin, int use_pullup); -extern int at91_set_gpio_output(unsigned pin, int value); -extern int at91_set_deglitch(unsigned pin, int is_on); -extern int at91_set_multi_drive(unsigned pin, int is_on); +extern int __init_or_module at91_set_A_periph(unsigned pin, int use_pullup); +extern int __init_or_module at91_set_B_periph(unsigned pin, int use_pullup); +extern int __init_or_module at91_set_gpio_input(unsigned pin, int use_pullup); +extern int __init_or_module at91_set_gpio_output(unsigned pin, int value); +extern int __init_or_module at91_set_deglitch(unsigned pin, int is_on); +extern int __init_or_module at91_set_multi_drive(unsigned pin, int is_on); /* callable at any time */ extern int at91_set_gpio_value(unsigned pin, int value); extern int at91_get_gpio_value(unsigned pin); +/* callable only from core power-management code */ extern void at91_gpio_suspend(void); extern void at91_gpio_resume(void); #endif