From: H. Peter Anvin Date: Wed, 11 Jul 2007 19:18:58 +0000 (-0700) Subject: Remove old i386 setup code X-Git-Tag: v2.6.23-rc1~1113 X-Git-Url: https://err.no/cgi-bin/gitweb.cgi?a=commitdiff_plain;h=c39736823232bc3ca113c8228fa852c09fba300e;p=linux-2.6 Remove old i386 setup code This removes the old i386 setup code. This is done as a separate patch to avoid breaking git bisect as some of the i386 code was also used by the old x86-64 code. Signed-off-by: H. Peter Anvin Signed-off-by: Linus Torvalds --- diff --git a/arch/i386/boot/bootsect.S b/arch/i386/boot/bootsect.S deleted file mode 100644 index 011b7a4993..0000000000 --- a/arch/i386/boot/bootsect.S +++ /dev/null @@ -1,98 +0,0 @@ -/* - * bootsect.S Copyright (C) 1991, 1992 Linus Torvalds - * - * modified by Drew Eckhardt - * modified by Bruce Evans (bde) - * modified by Chris Noe (May 1999) (as86 -> gas) - * gutted by H. Peter Anvin (Jan 2003) - * - * BIG FAT NOTE: We're in real mode using 64k segments. Therefore segment - * addresses must be multiplied by 16 to obtain their respective linear - * addresses. To avoid confusion, linear addresses are written using leading - * hex while segment addresses are written as segment:offset. - * - */ - -#include - -SETUPSECTS = 4 /* default nr of setup-sectors */ -BOOTSEG = 0x07C0 /* original address of boot-sector */ -INITSEG = DEF_INITSEG /* we move boot here - out of the way */ -SETUPSEG = DEF_SETUPSEG /* setup starts here */ -SYSSEG = DEF_SYSSEG /* system loaded at 0x10000 (65536) */ -SYSSIZE = DEF_SYSSIZE /* system size: # of 16-byte clicks */ - /* to be loaded */ -ROOT_DEV = 0 /* ROOT_DEV is now written by "build" */ -SWAP_DEV = 0 /* SWAP_DEV is now written by "build" */ - -#ifndef SVGA_MODE -#define SVGA_MODE ASK_VGA -#endif - -#ifndef RAMDISK -#define RAMDISK 0 -#endif - -#ifndef ROOT_RDONLY -#define ROOT_RDONLY 1 -#endif - -.code16 -.text - -.global _start -_start: - - # Normalize the start address - jmpl $BOOTSEG, $start2 - -start2: - movw %cs, %ax - movw %ax, %ds - movw %ax, %es - movw %ax, %ss - movw $0x7c00, %sp - sti - cld - - movw $bugger_off_msg, %si - -msg_loop: - lodsb - andb %al, %al - jz die - movb $0xe, %ah - movw $7, %bx - int $0x10 - jmp msg_loop - -die: - # Allow the user to press a key, then reboot - xorw %ax, %ax - int $0x16 - int $0x19 - - # int 0x19 should never return. In case it does anyway, - # invoke the BIOS reset code... - ljmp $0xf000,$0xfff0 - - -bugger_off_msg: - .ascii "Direct booting from floppy is no longer supported.\r\n" - .ascii "Please use a boot loader program instead.\r\n" - .ascii "\n" - .ascii "Remove disk and press any key to reboot . . .\r\n" - .byte 0 - - - # Kernel attributes; used by setup - - .org 497 -setup_sects: .byte SETUPSECTS -root_flags: .word ROOT_RDONLY -syssize: .word SYSSIZE -swap_dev: .word SWAP_DEV -ram_size: .word RAMDISK -vid_mode: .word SVGA_MODE -root_dev: .word ROOT_DEV -boot_flag: .word 0xAA55 diff --git a/arch/i386/boot/edd.S b/arch/i386/boot/edd.S deleted file mode 100644 index 3432136801..0000000000 --- a/arch/i386/boot/edd.S +++ /dev/null @@ -1,231 +0,0 @@ -/* - * BIOS Enhanced Disk Drive support - * Copyright (C) 2002, 2003, 2004 Dell, Inc. - * by Matt Domsch October 2002 - * conformant to T13 Committee www.t13.org - * projects 1572D, 1484D, 1386D, 1226DT - * disk signature read by Matt Domsch - * and Andrew Wilks September 2003, June 2004 - * legacy CHS retrieval by Patrick J. LoPresti - * March 2004 - * Command line option parsing, Matt Domsch, November 2004 - */ - -#include -#include - -#if defined(CONFIG_EDD) || defined(CONFIG_EDD_MODULE) - -# It is assumed that %ds == INITSEG here - - movb $0, (EDD_MBR_SIG_NR_BUF) - movb $0, (EDDNR) - -# Check the command line for options: -# edd=of disables EDD completely (edd=off) -# edd=sk skips the MBR test (edd=skipmbr) -# edd=on re-enables EDD (edd=on) - - pushl %esi - movw $edd_mbr_sig_start, %di # Default to edd=on - - movl %cs:(cmd_line_ptr), %esi - andl %esi, %esi - jz old_cl # Old boot protocol? - -# Convert to a real-mode pointer in fs:si - movl %esi, %eax - shrl $4, %eax - movw %ax, %fs - andw $0xf, %si - jmp have_cl_pointer - -# Old-style boot protocol? -old_cl: - push %ds # aka INITSEG - pop %fs - - cmpw $0xa33f, (0x20) - jne done_cl # No command line at all? - movw (0x22), %si # Pointer relative to INITSEG - -# fs:si has the pointer to the command line now -have_cl_pointer: - -# Loop through kernel command line one byte at a time. Just in -# case the loader is buggy and failed to null-terminate the command line -# terminate if we get close enough to the end of the segment that we -# cannot fit "edd=XX"... -cl_atspace: - cmpw $-5, %si # Watch for segment wraparound - jae done_cl - movl %fs:(%si), %eax - andb %al, %al # End of line? - jz done_cl - cmpl $EDD_CL_EQUALS, %eax - jz found_edd_equals - cmpb $0x20, %al # <= space consider whitespace - ja cl_skipword - incw %si - jmp cl_atspace - -cl_skipword: - cmpw $-5, %si # Watch for segment wraparound - jae done_cl - movb %fs:(%si), %al # End of string? - andb %al, %al - jz done_cl - cmpb $0x20, %al - jbe cl_atspace - incw %si - jmp cl_skipword - -found_edd_equals: -# only looking at first two characters after equals -# late overrides early on the command line, so keep going after finding something - movw %fs:4(%si), %ax - cmpw $EDD_CL_OFF, %ax # edd=of - je do_edd_off - cmpw $EDD_CL_SKIP, %ax # edd=sk - je do_edd_skipmbr - cmpw $EDD_CL_ON, %ax # edd=on - je do_edd_on - jmp cl_skipword -do_edd_skipmbr: - movw $edd_start, %di - jmp cl_skipword -do_edd_off: - movw $edd_done, %di - jmp cl_skipword -do_edd_on: - movw $edd_mbr_sig_start, %di - jmp cl_skipword - -done_cl: - popl %esi - jmpw *%di - -# Read the first sector of each BIOS disk device and store the 4-byte signature -edd_mbr_sig_start: - movb $0x80, %dl # from device 80 - movw $EDD_MBR_SIG_BUF, %bx # store buffer ptr in bx -edd_mbr_sig_read: - movl $0xFFFFFFFF, %eax - movl %eax, (%bx) # assume failure - pushw %bx - movb $READ_SECTORS, %ah - movb $1, %al # read 1 sector - movb $0, %dh # at head 0 - movw $1, %cx # cylinder 0, sector 0 - pushw %es - pushw %ds - popw %es - movw $EDDBUF, %bx # disk's data goes into EDDBUF - pushw %dx # work around buggy BIOSes - stc # work around buggy BIOSes - int $0x13 - sti # work around buggy BIOSes - popw %dx - popw %es - popw %bx - jc edd_mbr_sig_done # on failure, we're done. - cmpb $0, %ah # some BIOSes do not set CF - jne edd_mbr_sig_done # on failure, we're done. - movl (EDDBUF+EDD_MBR_SIG_OFFSET), %eax # read sig out of the MBR - movl %eax, (%bx) # store success - incb (EDD_MBR_SIG_NR_BUF) # note that we stored something - incb %dl # increment to next device - addw $4, %bx # increment sig buffer ptr - cmpb $EDD_MBR_SIG_MAX, (EDD_MBR_SIG_NR_BUF) # Out of space? - jb edd_mbr_sig_read # keep looping -edd_mbr_sig_done: - -# Do the BIOS Enhanced Disk Drive calls -# This consists of two calls: -# int 13h ah=41h "Check Extensions Present" -# int 13h ah=48h "Get Device Parameters" -# int 13h ah=08h "Legacy Get Device Parameters" -# -# A buffer of size EDDMAXNR*(EDDEXTSIZE+EDDPARMSIZE) is reserved for our use -# in the boot_params at EDDBUF. The first four bytes of which are -# used to store the device number, interface support map and version -# results from fn41. The next four bytes are used to store the legacy -# cylinders, heads, and sectors from fn08. The following 74 bytes are used to -# store the results from fn48. Starting from device 80h, fn41, then fn48 -# are called and their results stored in EDDBUF+n*(EDDEXTSIZE+EDDPARMIZE). -# Then the pointer is incremented to store the data for the next call. -# This repeats until either a device doesn't exist, or until EDDMAXNR -# devices have been stored. -# The one tricky part is that ds:si always points EDDEXTSIZE bytes into -# the structure, and the fn41 and fn08 results are stored at offsets -# from there. This removes the need to increment the pointer for -# every store, and leaves it ready for the fn48 call. -# A second one-byte buffer, EDDNR, in the boot_params stores -# the number of BIOS devices which exist, up to EDDMAXNR. -# In setup.c, copy_edd() stores both boot_params buffers away -# for later use, as they would get overwritten otherwise. -# This code is sensitive to the size of the structs in edd.h -edd_start: - # %ds points to the bootsector - # result buffer for fn48 - movw $EDDBUF+EDDEXTSIZE, %si # in ds:si, fn41 results - # kept just before that - movb $0x80, %dl # BIOS device 0x80 - -edd_check_ext: - movb $CHECKEXTENSIONSPRESENT, %ah # Function 41 - movw $EDDMAGIC1, %bx # magic - int $0x13 # make the call - jc edd_done # no more BIOS devices - - cmpw $EDDMAGIC2, %bx # is magic right? - jne edd_next # nope, next... - - movb %dl, %ds:-8(%si) # store device number - movb %ah, %ds:-7(%si) # store version - movw %cx, %ds:-6(%si) # store extensions - incb (EDDNR) # note that we stored something - -edd_get_device_params: - movw $EDDPARMSIZE, %ds:(%si) # put size - movw $0x0, %ds:2(%si) # work around buggy BIOSes - movb $GETDEVICEPARAMETERS, %ah # Function 48 - int $0x13 # make the call - # Don't check for fail return - # it doesn't matter. -edd_get_legacy_chs: - xorw %ax, %ax - movw %ax, %ds:-4(%si) - movw %ax, %ds:-2(%si) - # Ralf Brown's Interrupt List says to set ES:DI to - # 0000h:0000h "to guard against BIOS bugs" - pushw %es - movw %ax, %es - movw %ax, %di - pushw %dx # legacy call clobbers %dl - movb $LEGACYGETDEVICEPARAMETERS, %ah # Function 08 - int $0x13 # make the call - jc edd_legacy_done # failed - movb %cl, %al # Low 6 bits are max - andb $0x3F, %al # sector number - movb %al, %ds:-1(%si) # Record max sect - movb %dh, %ds:-2(%si) # Record max head number - movb %ch, %al # Low 8 bits of max cyl - shr $6, %cl - movb %cl, %ah # High 2 bits of max cyl - movw %ax, %ds:-4(%si) - -edd_legacy_done: - popw %dx - popw %es - movw %si, %ax # increment si - addw $EDDPARMSIZE+EDDEXTSIZE, %ax - movw %ax, %si - -edd_next: - incb %dl # increment to next device - cmpb $EDDMAXNR, (EDDNR) # Out of space? - jb edd_check_ext # keep looping - -edd_done: -#endif diff --git a/arch/i386/boot/setup.S b/arch/i386/boot/setup.S deleted file mode 100644 index 6dbcc95b21..0000000000 --- a/arch/i386/boot/setup.S +++ /dev/null @@ -1,1075 +0,0 @@ -/* - * setup.S Copyright (C) 1991, 1992 Linus Torvalds - * - * setup.s is responsible for getting the system data from the BIOS, - * and putting them into the appropriate places in system memory. - * both setup.s and system has been loaded by the bootblock. - * - * This code asks the bios for memory/disk/other parameters, and - * puts them in a "safe" place: 0x90000-0x901FF, ie where the - * boot-block used to be. It is then up to the protected mode - * system to read them from there before the area is overwritten - * for buffer-blocks. - * - * Move PS/2 aux init code to psaux.c - * (troyer@saifr00.cfsat.Honeywell.COM) 03Oct92 - * - * some changes and additional features by Christoph Niemann, - * March 1993/June 1994 (Christoph.Niemann@linux.org) - * - * add APM BIOS checking by Stephen Rothwell, May 1994 - * (sfr@canb.auug.org.au) - * - * High load stuff, initrd support and position independency - * by Hans Lermen & Werner Almesberger, February 1996 - * , - * - * Video handling moved to video.S by Martin Mares, March 1996 - * - * - * Extended memory detection scheme retwiddled by orc@pell.chi.il.us (david - * parsons) to avoid loadlin confusion, July 1997 - * - * Transcribed from Intel (as86) -> AT&T (gas) by Chris Noe, May 1999. - * - * - * Fix to work around buggy BIOSes which don't use carry bit correctly - * and/or report extended memory in CX/DX for e801h memory size detection - * call. As a result the kernel got wrong figures. The int15/e801h docs - * from Ralf Brown interrupt list seem to indicate AX/BX should be used - * anyway. So to avoid breaking many machines (presumably there was a reason - * to orginally use CX/DX instead of AX/BX), we do a kludge to see - * if CX/DX have been changed in the e801 call and if so use AX/BX . - * Michael Miller, April 2001 - * - * New A20 code ported from SYSLINUX by H. Peter Anvin. AMD Elan bugfixes - * by Robert Schwebel, December 2001 - */ - -#include -#include -#include -#include -#include -#include -#include - -/* Signature words to ensure LILO loaded us right */ -#define SIG1 0xAA55 -#define SIG2 0x5A5A - -INITSEG = DEF_INITSEG # 0x9000, we move boot here, out of the way -SYSSEG = DEF_SYSSEG # 0x1000, system loaded at 0x10000 (65536). -SETUPSEG = DEF_SETUPSEG # 0x9020, this is the current segment - # ... and the former contents of CS - -DELTA_INITSEG = SETUPSEG - INITSEG # 0x0020 - -.code16 -.globl begtext, begdata, begbss, endtext, enddata, endbss - -.text -begtext: -.data -begdata: -.bss -begbss: -.text - -start: - jmp trampoline - -# This is the setup header, and it must start at %cs:2 (old 0x9020:2) - - .ascii "HdrS" # header signature - .word 0x0206 # header version number (>= 0x0105) - # or else old loadlin-1.5 will fail) -realmode_swtch: .word 0, 0 # default_switch, SETUPSEG -start_sys_seg: .word SYSSEG - .word kernel_version # pointing to kernel version string - # above section of header is compatible - # with loadlin-1.5 (header v1.5). Don't - # change it. - -type_of_loader: .byte 0 # = 0, old one (LILO, Loadlin, - # Bootlin, SYSLX, bootsect...) - # See Documentation/i386/boot.txt for - # assigned ids - -# flags, unused bits must be zero (RFU) bit within loadflags -loadflags: -LOADED_HIGH = 1 # If set, the kernel is loaded high -CAN_USE_HEAP = 0x80 # If set, the loader also has set - # heap_end_ptr to tell how much - # space behind setup.S can be used for - # heap purposes. - # Only the loader knows what is free -#ifndef __BIG_KERNEL__ - .byte 0 -#else - .byte LOADED_HIGH -#endif - -setup_move_size: .word 0x8000 # size to move, when setup is not - # loaded at 0x90000. We will move setup - # to 0x90000 then just before jumping - # into the kernel. However, only the - # loader knows how much data behind - # us also needs to be loaded. - -code32_start: # here loaders can put a different - # start address for 32-bit code. -#ifndef __BIG_KERNEL__ - .long 0x1000 # 0x1000 = default for zImage -#else - .long 0x100000 # 0x100000 = default for big kernel -#endif - -ramdisk_image: .long 0 # address of loaded ramdisk image - # Here the loader puts the 32-bit - # address where it loaded the image. - # This only will be read by the kernel. - -ramdisk_size: .long 0 # its size in bytes - -bootsect_kludge: - .long 0 # obsolete - -heap_end_ptr: .word modelist+1024 # (Header version 0x0201 or later) - # space from here (exclusive) down to - # end of setup code can be used by setup - # for local heap purposes. - -pad1: .word 0 -cmd_line_ptr: .long 0 # (Header version 0x0202 or later) - # If nonzero, a 32-bit pointer - # to the kernel command line. - # The command line should be - # located between the start of - # setup and the end of low - # memory (0xa0000), or it may - # get overwritten before it - # gets read. If this field is - # used, there is no longer - # anything magical about the - # 0x90000 segment; the setup - # can be located anywhere in - # low memory 0x10000 or higher. - -ramdisk_max: .long (-__PAGE_OFFSET-(512 << 20)-1) & 0x7fffffff - # (Header version 0x0203 or later) - # The highest safe address for - # the contents of an initrd - -kernel_alignment: .long CONFIG_PHYSICAL_ALIGN #physical addr alignment - #required for protected mode - #kernel -#ifdef CONFIG_RELOCATABLE -relocatable_kernel: .byte 1 -#else -relocatable_kernel: .byte 0 -#endif -pad2: .byte 0 -pad3: .word 0 - -cmdline_size: .long COMMAND_LINE_SIZE-1 #length of the command line, - #added with boot protocol - #version 2.06 - -trampoline: call start_of_setup - .align 16 - # The offset at this point is 0x240 - .space (0xeff-0x240+1) # E820 & EDD space (ending at 0xeff) -# End of setup header ##################################################### - -start_of_setup: -# Bootlin depends on this being done early - movw $0x01500, %ax - movb $0x81, %dl - int $0x13 - -#ifdef SAFE_RESET_DISK_CONTROLLER -# Reset the disk controller. - movw $0x0000, %ax - movb $0x80, %dl - int $0x13 -#endif - -# Set %ds = %cs, we know that SETUPSEG = %cs at this point - movw %cs, %ax # aka SETUPSEG - movw %ax, %ds -# Check signature at end of setup - cmpw $SIG1, setup_sig1 - jne bad_sig - - cmpw $SIG2, setup_sig2 - jne bad_sig - - jmp good_sig1 - -# Routine to print asciiz string at ds:si -prtstr: - lodsb - andb %al, %al - jz fin - - call prtchr - jmp prtstr - -fin: ret - -# Space printing -prtsp2: call prtspc # Print double space -prtspc: movb $0x20, %al # Print single space (note: fall-thru) - -# Part of above routine, this one just prints ascii al -prtchr: pushw %ax - pushw %cx - movw $7,%bx - movw $0x01, %cx - movb $0x0e, %ah - int $0x10 - popw %cx - popw %ax - ret - -beep: movb $0x07, %al - jmp prtchr - -no_sig_mess: .string "No setup signature found ..." - -good_sig1: - jmp good_sig - -# We now have to find the rest of the setup code/data -bad_sig: - movw %cs, %ax # SETUPSEG - subw $DELTA_INITSEG, %ax # INITSEG - movw %ax, %ds - xorb %bh, %bh - movb (497), %bl # get setup sect from bootsect - subw $4, %bx # LILO loads 4 sectors of setup - shlw $8, %bx # convert to words (1sect=2^8 words) - movw %bx, %cx - shrw $3, %bx # convert to segment - addw $SYSSEG, %bx - movw %bx, %cs:start_sys_seg -# Move rest of setup code/data to here - movw $2048, %di # four sectors loaded by LILO - subw %si, %si - pushw %cs - popw %es - movw $SYSSEG, %ax - movw %ax, %ds - rep - movsw - movw %cs, %ax # aka SETUPSEG - movw %ax, %ds - cmpw $SIG1, setup_sig1 - jne no_sig - - cmpw $SIG2, setup_sig2 - jne no_sig - - jmp good_sig - -no_sig: - lea no_sig_mess, %si - call prtstr - -no_sig_loop: - hlt - jmp no_sig_loop - -good_sig: - movw %cs, %ax # aka SETUPSEG - subw $DELTA_INITSEG, %ax # aka INITSEG - movw %ax, %ds -# Check if an old loader tries to load a big-kernel - testb $LOADED_HIGH, %cs:loadflags # Do we have a big kernel? - jz loader_ok # No, no danger for old loaders. - - cmpb $0, %cs:type_of_loader # Do we have a loader that - # can deal with us? - jnz loader_ok # Yes, continue. - - pushw %cs # No, we have an old loader, - popw %ds # die. - lea loader_panic_mess, %si - call prtstr - - jmp no_sig_loop - -loader_panic_mess: .string "Wrong loader, giving up..." - -# check minimum cpuid -# we do this here because it is the last place we can actually -# show a user visible error message. Later the video modus -# might be already messed up. -loader_ok: - call verify_cpu - testl %eax,%eax - jz cpu_ok - movw %cs,%ax # aka SETUPSEG - movw %ax,%ds - lea cpu_panic_mess,%si - call prtstr -1: jmp 1b - -cpu_panic_mess: - .asciz "PANIC: CPU too old for this kernel." - -#include "../kernel/verify_cpu.S" - -cpu_ok: -# Get memory size (extended mem, kB) - - xorl %eax, %eax - movl %eax, (0x1e0) -#ifndef STANDARD_MEMORY_BIOS_CALL - movb %al, (E820NR) -# Try three different memory detection schemes. First, try -# e820h, which lets us assemble a memory map, then try e801h, -# which returns a 32-bit memory size, and finally 88h, which -# returns 0-64m - -# method E820H: -# the memory map from hell. e820h returns memory classified into -# a whole bunch of different types, and allows memory holes and -# everything. We scan through this memory map and build a list -# of the first 32 memory areas, which we return at [E820MAP]. -# This is documented at http://www.acpi.info/, in the ACPI 2.0 specification. - -#define SMAP 0x534d4150 - -meme820: - xorl %ebx, %ebx # continuation counter - movw $E820MAP, %di # point into the whitelist - # so we can have the bios - # directly write into it. - -jmpe820: - movl $0x0000e820, %eax # e820, upper word zeroed - movl $SMAP, %edx # ascii 'SMAP' - movl $20, %ecx # size of the e820rec - pushw %ds # data record. - popw %es - int $0x15 # make the call - jc bail820 # fall to e801 if it fails - - cmpl $SMAP, %eax # check the return is `SMAP' - jne bail820 # fall to e801 if it fails - -# cmpl $1, 16(%di) # is this usable memory? -# jne again820 - - # If this is usable memory, we save it by simply advancing %di by - # sizeof(e820rec). - # -good820: - movb (E820NR), %al # up to 128 entries - cmpb $E820MAX, %al - jae bail820 - - incb (E820NR) - movw %di, %ax - addw $20, %ax - movw %ax, %di -again820: - cmpl $0, %ebx # check to see if - jne jmpe820 # %ebx is set to EOF -bail820: - - -# method E801H: -# memory size is in 1k chunksizes, to avoid confusing loadlin. -# we store the 0xe801 memory size in a completely different place, -# because it will most likely be longer than 16 bits. -# (use 1e0 because that's what Larry Augustine uses in his -# alternative new memory detection scheme, and it's sensible -# to write everything into the same place.) - -meme801: - stc # fix to work around buggy - xorw %cx,%cx # BIOSes which don't clear/set - xorw %dx,%dx # carry on pass/error of - # e801h memory size call - # or merely pass cx,dx though - # without changing them. - movw $0xe801, %ax - int $0x15 - jc mem88 - - cmpw $0x0, %cx # Kludge to handle BIOSes - jne e801usecxdx # which report their extended - cmpw $0x0, %dx # memory in AX/BX rather than - jne e801usecxdx # CX/DX. The spec I have read - movw %ax, %cx # seems to indicate AX/BX - movw %bx, %dx # are more reasonable anyway... - -e801usecxdx: - andl $0xffff, %edx # clear sign extend - shll $6, %edx # and go from 64k to 1k chunks - movl %edx, (0x1e0) # store extended memory size - andl $0xffff, %ecx # clear sign extend - addl %ecx, (0x1e0) # and add lower memory into - # total size. - -# Ye Olde Traditional Methode. Returns the memory size (up to 16mb or -# 64mb, depending on the bios) in ax. -mem88: - -#endif - movb $0x88, %ah - int $0x15 - movw %ax, (2) - -# Set the keyboard repeat rate to the max - movw $0x0305, %ax - xorw %bx, %bx - int $0x16 - -# Check for video adapter and its parameters and allow the -# user to browse video modes. - call video # NOTE: we need %ds pointing - # to bootsector - -# Get hd0 data... - xorw %ax, %ax - movw %ax, %ds - ldsw (4 * 0x41), %si - movw %cs, %ax # aka SETUPSEG - subw $DELTA_INITSEG, %ax # aka INITSEG - pushw %ax - movw %ax, %es - movw $0x0080, %di - movw $0x10, %cx - pushw %cx - cld - rep - movsb -# Get hd1 data... - xorw %ax, %ax - movw %ax, %ds - ldsw (4 * 0x46), %si - popw %cx - popw %es - movw $0x0090, %di - rep - movsb -# Check that there IS a hd1 :-) - movw $0x01500, %ax - movb $0x81, %dl - int $0x13 - jc no_disk1 - - cmpb $3, %ah - je is_disk1 - -no_disk1: - movw %cs, %ax # aka SETUPSEG - subw $DELTA_INITSEG, %ax # aka INITSEG - movw %ax, %es - movw $0x0090, %di - movw $0x10, %cx - xorw %ax, %ax - cld - rep - stosb -is_disk1: -# check for Micro Channel (MCA) bus - movw %cs, %ax # aka SETUPSEG - subw $DELTA_INITSEG, %ax # aka INITSEG - movw %ax, %ds - xorw %ax, %ax - movw %ax, (0xa0) # set table length to 0 - movb $0xc0, %ah - stc - int $0x15 # moves feature table to es:bx - jc no_mca - - pushw %ds - movw %es, %ax - movw %ax, %ds - movw %cs, %ax # aka SETUPSEG - subw $DELTA_INITSEG, %ax # aka INITSEG - movw %ax, %es - movw %bx, %si - movw $0xa0, %di - movw (%si), %cx - addw $2, %cx # table length is a short - cmpw $0x10, %cx - jc sysdesc_ok - - movw $0x10, %cx # we keep only first 16 bytes -sysdesc_ok: - rep - movsb - popw %ds -no_mca: -#ifdef CONFIG_X86_VOYAGER - movb $0xff, 0x40 # flag on config found - movb $0xc0, %al - mov $0xff, %ah - int $0x15 # put voyager config info at es:di - jc no_voyager - movw $0x40, %si # place voyager info in apm table - cld - movw $7, %cx -voyager_rep: - movb %es:(%di), %al - movb %al,(%si) - incw %di - incw %si - decw %cx - jnz voyager_rep -no_voyager: -#endif -# Check for PS/2 pointing device - movw %cs, %ax # aka SETUPSEG - subw $DELTA_INITSEG, %ax # aka INITSEG - movw %ax, %ds - movb $0, (0x1ff) # default is no pointing device - int $0x11 # int 0x11: equipment list - testb $0x04, %al # check if mouse installed - jz no_psmouse - - movb $0xAA, (0x1ff) # device present -no_psmouse: - -#if defined(CONFIG_X86_SPEEDSTEP_SMI) || defined(CONFIG_X86_SPEEDSTEP_SMI_MODULE) - movl $0x0000E980, %eax # IST Support - movl $0x47534943, %edx # Request value - int $0x15 - - movl %eax, (96) - movl %ebx, (100) - movl %ecx, (104) - movl %edx, (108) -#endif - -#if defined(CONFIG_APM) || defined(CONFIG_APM_MODULE) -# Then check for an APM BIOS... - # %ds points to the bootsector - movw $0, 0x40 # version = 0 means no APM BIOS - movw $0x05300, %ax # APM BIOS installation check - xorw %bx, %bx - int $0x15 - jc done_apm_bios # Nope, no APM BIOS - - cmpw $0x0504d, %bx # Check for "PM" signature - jne done_apm_bios # No signature, no APM BIOS - - andw $0x02, %cx # Is 32 bit supported? - je done_apm_bios # No 32-bit, no (good) APM BIOS - - movw $0x05304, %ax # Disconnect first just in case - xorw %bx, %bx - int $0x15 # ignore return code - movw $0x05303, %ax # 32 bit connect - xorl %ebx, %ebx - xorw %cx, %cx # paranoia :-) - xorw %dx, %dx # ... - xorl %esi, %esi # ... - xorw %di, %di # ... - int $0x15 - jc no_32_apm_bios # Ack, error. - - movw %ax, (66) # BIOS code segment - movl %ebx, (68) # BIOS entry point offset - movw %cx, (72) # BIOS 16 bit code segment - movw %dx, (74) # BIOS data segment - movl %esi, (78) # BIOS code segment lengths - movw %di, (82) # BIOS data segment length -# Redo the installation check as the 32 bit connect -# modifies the flags returned on some BIOSs - movw $0x05300, %ax # APM BIOS installation check - xorw %bx, %bx - xorw %cx, %cx # paranoia - int $0x15 - jc apm_disconnect # error -> shouldn't happen - - cmpw $0x0504d, %bx # check for "PM" signature - jne apm_disconnect # no sig -> shouldn't happen - - movw %ax, (64) # record the APM BIOS version - movw %cx, (76) # and flags - jmp done_apm_bios - -apm_disconnect: # Tidy up - movw $0x05304, %ax # Disconnect - xorw %bx, %bx - int $0x15 # ignore return code - - jmp done_apm_bios - -no_32_apm_bios: - andw $0xfffd, (76) # remove 32 bit support bit -done_apm_bios: -#endif - -#include "edd.S" - -# Now we want to move to protected mode ... - cmpw $0, %cs:realmode_swtch - jz rmodeswtch_normal - - lcall *%cs:realmode_swtch - - jmp rmodeswtch_end - -rmodeswtch_normal: - pushw %cs - call default_switch - -rmodeswtch_end: -# Now we move the system to its rightful place ... but we check if we have a -# big-kernel. In that case we *must* not move it ... - testb $LOADED_HIGH, %cs:loadflags - jz do_move0 # .. then we have a normal low - # loaded zImage - # .. or else we have a high - # loaded bzImage - jmp end_move # ... and we skip moving - -do_move0: - movw $0x100, %ax # start of destination segment - movw %cs, %bp # aka SETUPSEG - subw $DELTA_INITSEG, %bp # aka INITSEG - movw %cs:start_sys_seg, %bx # start of source segment - cld -do_move: - movw %ax, %es # destination segment - incb %ah # instead of add ax,#0x100 - movw %bx, %ds # source segment - addw $0x100, %bx - subw %di, %di - subw %si, %si - movw $0x800, %cx - rep - movsw - cmpw %bp, %bx # assume start_sys_seg > 0x200, - # so we will perhaps read one - # page more than needed, but - # never overwrite INITSEG - # because destination is a - # minimum one page below source - jb do_move - -end_move: -# then we load the segment descriptors - movw %cs, %ax # aka SETUPSEG - movw %ax, %ds - -# Check whether we need to be downward compatible with version <=201 - cmpl $0, cmd_line_ptr - jne end_move_self # loader uses version >=202 features - cmpb $0x20, type_of_loader - je end_move_self # bootsect loader, we know of it - -# Boot loader doesnt support boot protocol version 2.02. -# If we have our code not at 0x90000, we need to move it there now. -# We also then need to move the params behind it (commandline) -# Because we would overwrite the code on the current IP, we move -# it in two steps, jumping high after the first one. - movw %cs, %ax - cmpw $SETUPSEG, %ax - je end_move_self - - cli # make sure we really have - # interrupts disabled ! - # because after this the stack - # should not be used - subw $DELTA_INITSEG, %ax # aka INITSEG - movw %ss, %dx - cmpw %ax, %dx - jb move_self_1 - - addw $INITSEG, %dx - subw %ax, %dx # this will go into %ss after - # the move -move_self_1: - movw %ax, %ds - movw $INITSEG, %ax # real INITSEG - movw %ax, %es - movw %cs:setup_move_size, %cx - std # we have to move up, so we use - # direction down because the - # areas may overlap - movw %cx, %di - decw %di - movw %di, %si - subw $move_self_here+0x200, %cx - rep - movsb - ljmp $SETUPSEG, $move_self_here - -move_self_here: - movw $move_self_here+0x200, %cx - rep - movsb - movw $SETUPSEG, %ax - movw %ax, %ds - movw %dx, %ss -end_move_self: # now we are at the right place - -# -# Enable A20. This is at the very best an annoying procedure. -# A20 code ported from SYSLINUX 1.52-1.63 by H. Peter Anvin. -# AMD Elan bug fix by Robert Schwebel. -# - -#if defined(CONFIG_X86_ELAN) - movb $0x02, %al # alternate A20 gate - outb %al, $0x92 # this works on SC410/SC520 -a20_elan_wait: - call a20_test - jz a20_elan_wait - jmp a20_done -#endif - - -A20_TEST_LOOPS = 32 # Iterations per wait -A20_ENABLE_LOOPS = 255 # Total loops to try - - -#ifndef CONFIG_X86_VOYAGER -a20_try_loop: - - # First, see if we are on a system with no A20 gate. -a20_none: - call a20_test - jnz a20_done - - # Next, try the BIOS (INT 0x15, AX=0x2401) -a20_bios: - movw $0x2401, %ax - pushfl # Be paranoid about flags - int $0x15 - popfl - - call a20_test - jnz a20_done - - # Try enabling A20 through the keyboard controller -#endif /* CONFIG_X86_VOYAGER */ -a20_kbc: - call empty_8042 - -#ifndef CONFIG_X86_VOYAGER - call a20_test # Just in case the BIOS worked - jnz a20_done # but had a delayed reaction. -#endif - - movb $0xD1, %al # command write - outb %al, $0x64 - call empty_8042 - - movb $0xDF, %al # A20 on - outb %al, $0x60 - call empty_8042 - -#ifndef CONFIG_X86_VOYAGER - # Wait until a20 really *is* enabled; it can take a fair amount of - # time on certain systems; Toshiba Tecras are known to have this - # problem. -a20_kbc_wait: - xorw %cx, %cx -a20_kbc_wait_loop: - call a20_test - jnz a20_done - loop a20_kbc_wait_loop - - # Final attempt: use "configuration port A" -a20_fast: - inb $0x92, %al # Configuration Port A - orb $0x02, %al # "fast A20" version - andb $0xFE, %al # don't accidentally reset - outb %al, $0x92 - - # Wait for configuration port A to take effect -a20_fast_wait: - xorw %cx, %cx -a20_fast_wait_loop: - call a20_test - jnz a20_done - loop a20_fast_wait_loop - - # A20 is still not responding. Try frobbing it again. - # - decb (a20_tries) - jnz a20_try_loop - - movw $a20_err_msg, %si - call prtstr - -a20_die: - hlt - jmp a20_die - -a20_tries: - .byte A20_ENABLE_LOOPS - -a20_err_msg: - .ascii "linux: fatal error: A20 gate not responding!" - .byte 13, 10, 0 - - # If we get here, all is good -a20_done: - -#endif /* CONFIG_X86_VOYAGER */ -# set up gdt and idt and 32bit start address - lidt idt_48 # load idt with 0,0 - xorl %eax, %eax # Compute gdt_base - movw %ds, %ax # (Convert %ds:gdt to a linear ptr) - shll $4, %eax - addl %eax, code32 - addl $gdt, %eax - movl %eax, (gdt_48+2) - lgdt gdt_48 # load gdt with whatever is - # appropriate - -# make sure any possible coprocessor is properly reset.. - xorw %ax, %ax - outb %al, $0xf0 - call delay - - outb %al, $0xf1 - call delay - -# well, that went ok, I hope. Now we mask all interrupts - the rest -# is done in init_IRQ(). - movb $0xFF, %al # mask all interrupts for now - outb %al, $0xA1 - call delay - - movb $0xFB, %al # mask all irq's but irq2 which - outb %al, $0x21 # is cascaded - -# Well, that certainly wasn't fun :-(. Hopefully it works, and we don't -# need no steenking BIOS anyway (except for the initial loading :-). -# The BIOS-routine wants lots of unnecessary data, and it's less -# "interesting" anyway. This is how REAL programmers do it. -# -# Well, now's the time to actually move into protected mode. To make -# things as simple as possible, we do no register set-up or anything, -# we let the gnu-compiled 32-bit programs do that. We just jump to -# absolute address 0x1000 (or the loader supplied one), -# in 32-bit protected mode. -# -# Note that the short jump isn't strictly needed, although there are -# reasons why it might be a good idea. It won't hurt in any case. - movw $1, %ax # protected mode (PE) bit - lmsw %ax # This is it! - jmp flush_instr - -flush_instr: - xorw %bx, %bx # Flag to indicate a boot - xorl %esi, %esi # Pointer to real-mode code - movw %cs, %si - subw $DELTA_INITSEG, %si - shll $4, %esi # Convert to 32-bit pointer - -# jump to startup_32 in arch/i386/boot/compressed/head.S -# -# NOTE: For high loaded big kernels we need a -# jmpi 0x100000,__BOOT_CS -# -# but we yet haven't reloaded the CS register, so the default size -# of the target offset still is 16 bit. -# However, using an operand prefix (0x66), the CPU will properly -# take our 48 bit far pointer. (INTeL 80386 Programmer's Reference -# Manual, Mixing 16-bit and 32-bit code, page 16-6) - - .byte 0x66, 0xea # prefix + jmpi-opcode -code32: .long startup_32 # will be set to %cs+startup_32 - .word __BOOT_CS -.code32 -startup_32: - movl $(__BOOT_DS), %eax - movl %eax, %ds - movl %eax, %es - movl %eax, %fs - movl %eax, %gs - movl %eax, %ss - - xorl %eax, %eax -1: incl %eax # check that A20 really IS enabled - movl %eax, 0x00000000 # loop forever if it isn't - cmpl %eax, 0x00100000 - je 1b - - # Jump to the 32bit entry point - jmpl *(code32_start - start + (DELTA_INITSEG << 4))(%esi) -.code16 - -# Here's a bunch of information about your current kernel.. -kernel_version: .ascii UTS_RELEASE - .ascii " (" - .ascii LINUX_COMPILE_BY - .ascii "@" - .ascii LINUX_COMPILE_HOST - .ascii ") " - .ascii UTS_VERSION - .byte 0 - -# This is the default real mode switch routine. -# to be called just before protected mode transition -default_switch: - cli # no interrupts allowed ! - movb $0x80, %al # disable NMI for bootup - # sequence - outb %al, $0x70 - lret - - -#ifndef CONFIG_X86_VOYAGER -# This routine tests whether or not A20 is enabled. If so, it -# exits with zf = 0. -# -# The memory address used, 0x200, is the int $0x80 vector, which -# should be safe. - -A20_TEST_ADDR = 4*0x80 - -a20_test: - pushw %cx - pushw %ax - xorw %cx, %cx - movw %cx, %fs # Low memory - decw %cx - movw %cx, %gs # High memory area - movw $A20_TEST_LOOPS, %cx - movw %fs:(A20_TEST_ADDR), %ax - pushw %ax -a20_test_wait: - incw %ax - movw %ax, %fs:(A20_TEST_ADDR) - call delay # Serialize and make delay constant - cmpw %gs:(A20_TEST_ADDR+0x10), %ax - loope a20_test_wait - - popw %fs:(A20_TEST_ADDR) - popw %ax - popw %cx - ret - -#endif /* CONFIG_X86_VOYAGER */ - -# This routine checks that the keyboard command queue is empty -# (after emptying the output buffers) -# -# Some machines have delusions that the keyboard buffer is always full -# with no keyboard attached... -# -# If there is no keyboard controller, we will usually get 0xff -# to all the reads. With each IO taking a microsecond and -# a timeout of 100,000 iterations, this can take about half a -# second ("delay" == outb to port 0x80). That should be ok, -# and should also be plenty of time for a real keyboard controller -# to empty. -# - -empty_8042: - pushl %ecx - movl $100000, %ecx - -empty_8042_loop: - decl %ecx - jz empty_8042_end_loop - - call delay - - inb $0x64, %al # 8042 status port - testb $1, %al # output buffer? - jz no_output - - call delay - inb $0x60, %al # read it - jmp empty_8042_loop - -no_output: - testb $2, %al # is input buffer full? - jnz empty_8042_loop # yes - loop -empty_8042_end_loop: - popl %ecx - ret - -# Read the cmos clock. Return the seconds in al -gettime: - pushw %cx - movb $0x02, %ah - int $0x1a - movb %dh, %al # %dh contains the seconds - andb $0x0f, %al - movb %dh, %ah - movb $0x04, %cl - shrb %cl, %ah - aad - popw %cx - ret - -# Delay is needed after doing I/O -delay: - outb %al,$0x80 - ret - -# Descriptor tables -# -# NOTE: The intel manual says gdt should be sixteen bytes aligned for -# efficiency reasons. However, there are machines which are known not -# to boot with misaligned GDTs, so alter this at your peril! If you alter -# GDT_ENTRY_BOOT_CS (in asm/segment.h) remember to leave at least two -# empty GDT entries (one for NULL and one reserved). -# -# NOTE: On some CPUs, the GDT must be 8 byte aligned. This is -# true for the Voyager Quad CPU card which will not boot without -# This directive. 16 byte aligment is recommended by intel. -# - .align 16 -gdt: - .fill GDT_ENTRY_BOOT_CS,8,0 - - .word 0xFFFF # 4Gb - (0x100000*0x1000 = 4Gb) - .word 0 # base address = 0 - .word 0x9A00 # code read/exec - .word 0x00CF # granularity = 4096, 386 - # (+5th nibble of limit) - - .word 0xFFFF # 4Gb - (0x100000*0x1000 = 4Gb) - .word 0 # base address = 0 - .word 0x9200 # data read/write - .word 0x00CF # granularity = 4096, 386 - # (+5th nibble of limit) -gdt_end: - .align 4 - - .word 0 # alignment byte -idt_48: - .word 0 # idt limit = 0 - .word 0, 0 # idt base = 0L - - .word 0 # alignment byte -gdt_48: - .word gdt_end - gdt - 1 # gdt limit - .word 0, 0 # gdt base (filled in later) - -# Include video setup & detection code - -#include "video.S" - -# Setup signature -- must be last -setup_sig1: .word SIG1 -setup_sig2: .word SIG2 - -# After this point, there is some free space which is used by the video mode -# handling code to store the temporary mode table (not used by the kernel). - -modelist: - -.text -endtext: -.data -enddata: -.bss -endbss: diff --git a/arch/i386/boot/video.S b/arch/i386/boot/video.S deleted file mode 100644 index 8143c9516c..0000000000 --- a/arch/i386/boot/video.S +++ /dev/null @@ -1,2043 +0,0 @@ -/* video.S - * - * Display adapter & video mode setup, version 2.13 (14-May-99) - * - * Copyright (C) 1995 -- 1998 Martin Mares - * Based on the original setup.S code (C) Linus Torvalds and Mats Anderson - * - * Rewritten to use GNU 'as' by Chris Noe May 1999 - * - * For further information, look at Documentation/svga.txt. - * - */ - -/* Enable autodetection of SVGA adapters and modes. */ -#undef CONFIG_VIDEO_SVGA - -/* Enable autodetection of VESA modes */ -#define CONFIG_VIDEO_VESA - -/* Enable compacting of mode table */ -#define CONFIG_VIDEO_COMPACT - -/* Retain screen contents when switching modes */ -#define CONFIG_VIDEO_RETAIN - -/* Enable local mode list */ -#undef CONFIG_VIDEO_LOCAL - -/* Force 400 scan lines for standard modes (hack to fix bad BIOS behaviour */ -#undef CONFIG_VIDEO_400_HACK - -/* Hack that lets you force specific BIOS mode ID and specific dimensions */ -#undef CONFIG_VIDEO_GFX_HACK -#define VIDEO_GFX_BIOS_AX 0x4f02 /* 800x600 on ThinkPad */ -#define VIDEO_GFX_BIOS_BX 0x0102 -#define VIDEO_GFX_DUMMY_RESOLUTION 0x6425 /* 100x37 */ - -/* This code uses an extended set of video mode numbers. These include: - * Aliases for standard modes - * NORMAL_VGA (-1) - * EXTENDED_VGA (-2) - * ASK_VGA (-3) - * Video modes numbered by menu position -- NOT RECOMMENDED because of lack - * of compatibility when extending the table. These are between 0x00 and 0xff. - */ -#define VIDEO_FIRST_MENU 0x0000 - -/* Standard BIOS video modes (BIOS number + 0x0100) */ -#define VIDEO_FIRST_BIOS 0x0100 - -/* VESA BIOS video modes (VESA number + 0x0200) */ -#define VIDEO_FIRST_VESA 0x0200 - -/* Video7 special modes (BIOS number + 0x0900) */ -#define VIDEO_FIRST_V7 0x0900 - -/* Special video modes */ -#define VIDEO_FIRST_SPECIAL 0x0f00 -#define VIDEO_80x25 0x0f00 -#define VIDEO_8POINT 0x0f01 -#define VIDEO_80x43 0x0f02 -#define VIDEO_80x28 0x0f03 -#define VIDEO_CURRENT_MODE 0x0f04 -#define VIDEO_80x30 0x0f05 -#define VIDEO_80x34 0x0f06 -#define VIDEO_80x60 0x0f07 -#define VIDEO_GFX_HACK 0x0f08 -#define VIDEO_LAST_SPECIAL 0x0f09 - -/* Video modes given by resolution */ -#define VIDEO_FIRST_RESOLUTION 0x1000 - -/* The "recalculate timings" flag */ -#define VIDEO_RECALC 0x8000 - -/* Positions of various video parameters passed to the kernel */ -/* (see also include/linux/tty.h) */ -#define PARAM_CURSOR_POS 0x00 -#define PARAM_VIDEO_PAGE 0x04 -#define PARAM_VIDEO_MODE 0x06 -#define PARAM_VIDEO_COLS 0x07 -#define PARAM_VIDEO_EGA_BX 0x0a -#define PARAM_VIDEO_LINES 0x0e -#define PARAM_HAVE_VGA 0x0f -#define PARAM_FONT_POINTS 0x10 - -#define PARAM_LFB_WIDTH 0x12 -#define PARAM_LFB_HEIGHT 0x14 -#define PARAM_LFB_DEPTH 0x16 -#define PARAM_LFB_BASE 0x18 -#define PARAM_LFB_SIZE 0x1c -#define PARAM_LFB_LINELENGTH 0x24 -#define PARAM_LFB_COLORS 0x26 -#define PARAM_VESAPM_SEG 0x2e -#define PARAM_VESAPM_OFF 0x30 -#define PARAM_LFB_PAGES 0x32 -#define PARAM_VESA_ATTRIB 0x34 -#define PARAM_CAPABILITIES 0x36 - -/* Define DO_STORE according to CONFIG_VIDEO_RETAIN */ -#ifdef CONFIG_VIDEO_RETAIN -#define DO_STORE call store_screen -#else -#define DO_STORE -#endif /* CONFIG_VIDEO_RETAIN */ - -# This is the main entry point called by setup.S -# %ds *must* be pointing to the bootsector -video: pushw %ds # We use different segments - pushw %ds # FS contains original DS - popw %fs - pushw %cs # DS is equal to CS - popw %ds - pushw %cs # ES is equal to CS - popw %es - xorw %ax, %ax - movw %ax, %gs # GS is zero - cld - call basic_detect # Basic adapter type testing (EGA/VGA/MDA/CGA) -#ifdef CONFIG_VIDEO_SELECT - movw %fs:(0x01fa), %ax # User selected video mode - cmpw $ASK_VGA, %ax # Bring up the menu - jz vid2 - - call mode_set # Set the mode - jc vid1 - - leaw badmdt, %si # Invalid mode ID - call prtstr -vid2: call mode_menu -vid1: -#ifdef CONFIG_VIDEO_RETAIN - call restore_screen # Restore screen contents -#endif /* CONFIG_VIDEO_RETAIN */ - call store_edid -#endif /* CONFIG_VIDEO_SELECT */ - call mode_params # Store mode parameters - popw %ds # Restore original DS - ret - -# Detect if we have CGA, MDA, EGA or VGA and pass it to the kernel. -basic_detect: - movb $0, %fs:(PARAM_HAVE_VGA) - movb $0x12, %ah # Check EGA/VGA - movb $0x10, %bl - int $0x10 - movw %bx, %fs:(PARAM_VIDEO_EGA_BX) # Identifies EGA to the kernel - cmpb $0x10, %bl # No, it's a CGA/MDA/HGA card. - je basret - - incb adapter - movw $0x1a00, %ax # Check EGA or VGA? - int $0x10 - cmpb $0x1a, %al # 1a means VGA... - jne basret # anything else is EGA. - - incb %fs:(PARAM_HAVE_VGA) # We've detected a VGA - incb adapter -basret: ret - -# Store the video mode parameters for later usage by the kernel. -# This is done by asking the BIOS except for the rows/columns -# parameters in the default 80x25 mode -- these are set directly, -# because some very obscure BIOSes supply insane values. -mode_params: -#ifdef CONFIG_VIDEO_SELECT - cmpb $0, graphic_mode - jnz mopar_gr -#endif - movb $0x03, %ah # Read cursor position - xorb %bh, %bh - int $0x10 - movw %dx, %fs:(PARAM_CURSOR_POS) - movb $0x0f, %ah # Read page/mode/width - int $0x10 - movw %bx, %fs:(PARAM_VIDEO_PAGE) - movw %ax, %fs:(PARAM_VIDEO_MODE) # Video mode and screen width - cmpb $0x7, %al # MDA/HGA => segment differs - jnz mopar0 - - movw $0xb000, video_segment -mopar0: movw %gs:(0x485), %ax # Font size - movw %ax, %fs:(PARAM_FONT_POINTS) # (valid only on EGA/VGA) - movw force_size, %ax # Forced size? - orw %ax, %ax - jz mopar1 - - movb %ah, %fs:(PARAM_VIDEO_COLS) - movb %al, %fs:(PARAM_VIDEO_LINES) - ret - -mopar1: movb $25, %al - cmpb $0, adapter # If we are on CGA/MDA/HGA, the - jz mopar2 # screen must have 25 lines. - - movb %gs:(0x484), %al # On EGA/VGA, use the EGA+ BIOS - incb %al # location of max lines. -mopar2: movb %al, %fs:(PARAM_VIDEO_LINES) - ret - -#ifdef CONFIG_VIDEO_SELECT -# Fetching of VESA frame buffer parameters -mopar_gr: - leaw modelist+1024, %di - movb $0x23, %fs:(PARAM_HAVE_VGA) - movw 16(%di), %ax - movw %ax, %fs:(PARAM_LFB_LINELENGTH) - movw 18(%di), %ax - movw %ax, %fs:(PARAM_LFB_WIDTH) - movw 20(%di), %ax - movw %ax, %fs:(PARAM_LFB_HEIGHT) - movb 25(%di), %al - movb $0, %ah - movw %ax, %fs:(PARAM_LFB_DEPTH) - movb 29(%di), %al - movb $0, %ah - movw %ax, %fs:(PARAM_LFB_PAGES) - movl 40(%di), %eax - movl %eax, %fs:(PARAM_LFB_BASE) - movl 31(%di), %eax - movl %eax, %fs:(PARAM_LFB_COLORS) - movl 35(%di), %eax - movl %eax, %fs:(PARAM_LFB_COLORS+4) - movw 0(%di), %ax - movw %ax, %fs:(PARAM_VESA_ATTRIB) - -# get video mem size - leaw modelist+1024, %di - movw $0x4f00, %ax - int $0x10 - xorl %eax, %eax - movw 18(%di), %ax - movl %eax, %fs:(PARAM_LFB_SIZE) - -# store mode capabilities - movl 10(%di), %eax - movl %eax, %fs:(PARAM_CAPABILITIES) - -# switching the DAC to 8-bit is for <= 8 bpp only - movw %fs:(PARAM_LFB_DEPTH), %ax - cmpw $8, %ax - jg dac_done - -# get DAC switching capability - xorl %eax, %eax - movb 10(%di), %al - testb $1, %al - jz dac_set - -# attempt to switch DAC to 8-bit - movw $0x4f08, %ax - movw $0x0800, %bx - int $0x10 - cmpw $0x004f, %ax - jne dac_set - movb %bh, dac_size # store actual DAC size - -dac_set: -# set color size to DAC size - movb dac_size, %al - movb %al, %fs:(PARAM_LFB_COLORS+0) - movb %al, %fs:(PARAM_LFB_COLORS+2) - movb %al, %fs:(PARAM_LFB_COLORS+4) - movb %al, %fs:(PARAM_LFB_COLORS+6) - -# set color offsets to 0 - movb $0, %fs:(PARAM_LFB_COLORS+1) - movb $0, %fs:(PARAM_LFB_COLORS+3) - movb $0, %fs:(PARAM_LFB_COLORS+5) - movb $0, %fs:(PARAM_LFB_COLORS+7) - -dac_done: -# get protected mode interface informations - movw $0x4f0a, %ax - xorw %bx, %bx - xorw %di, %di - int $0x10 - cmp $0x004f, %ax - jnz no_pm - - movw %es, %fs:(PARAM_VESAPM_SEG) - movw %di, %fs:(PARAM_VESAPM_OFF) -no_pm: ret - -# The video mode menu -mode_menu: - leaw keymsg, %si # "Return/Space/Timeout" message - call prtstr - call flush -nokey: call getkt - - cmpb $0x0d, %al # ENTER ? - je listm # yes - manual mode selection - - cmpb $0x20, %al # SPACE ? - je defmd1 # no - repeat - - call beep - jmp nokey - -defmd1: ret # No mode chosen? Default 80x25 - -listm: call mode_table # List mode table -listm0: leaw name_bann, %si # Print adapter name - call prtstr - movw card_name, %si - orw %si, %si - jnz an2 - - movb adapter, %al - leaw old_name, %si - orb %al, %al - jz an1 - - leaw ega_name, %si - decb %al - jz an1 - - leaw vga_name, %si - jmp an1 - -an2: call prtstr - leaw svga_name, %si -an1: call prtstr - leaw listhdr, %si # Table header - call prtstr - movb $0x30, %dl # DL holds mode number - leaw modelist, %si -lm1: cmpw $ASK_VGA, (%si) # End? - jz lm2 - - movb %dl, %al # Menu selection number - call prtchr - call prtsp2 - lodsw - call prthw # Mode ID - call prtsp2 - movb 0x1(%si), %al - call prtdec # Rows - movb $0x78, %al # the letter 'x' - call prtchr - lodsw - call prtdec # Columns - movb $0x0d, %al # New line - call prtchr - movb $0x0a, %al - call prtchr - incb %dl # Next character - cmpb $0x3a, %dl - jnz lm1 - - movb $0x61, %dl - jmp lm1 - -lm2: leaw prompt, %si # Mode prompt - call prtstr - leaw edit_buf, %di # Editor buffer -lm3: call getkey - cmpb $0x0d, %al # Enter? - jz lment - - cmpb $0x08, %al # Backspace? - jz lmbs - - cmpb $0x20, %al # Printable? - jc lm3 - - cmpw $edit_buf+4, %di # Enough space? - jz lm3 - - stosb - call prtchr - jmp lm3 - -lmbs: cmpw $edit_buf, %di # Backspace - jz lm3 - - decw %di - movb $0x08, %al - call prtchr - call prtspc - movb $0x08, %al - call prtchr - jmp lm3 - -lment: movb $0, (%di) - leaw crlft, %si - call prtstr - leaw edit_buf, %si - cmpb $0, (%si) # Empty string = default mode - jz lmdef - - cmpb $0, 1(%si) # One character = menu selection - jz mnusel - - cmpw $0x6373, (%si) # "scan" => mode scanning - jnz lmhx - - cmpw $0x6e61, 2(%si) - jz lmscan - -lmhx: xorw %bx, %bx # Else => mode ID in hex -lmhex: lodsb - orb %al, %al - jz lmuse1 - - subb $0x30, %al - jc lmbad - - cmpb $10, %al - jc lmhx1 - - subb $7, %al - andb $0xdf, %al - cmpb $10, %al - jc lmbad - - cmpb $16, %al - jnc lmbad - -lmhx1: shlw $4, %bx - orb %al, %bl - jmp lmhex - -lmuse1: movw %bx, %ax - jmp lmuse - -mnusel: lodsb # Menu selection - xorb %ah, %ah - subb $0x30, %al - jc lmbad - - cmpb $10, %al - jc lmuse - - cmpb $0x61-0x30, %al - jc lmbad - - subb $0x61-0x30-10, %al - cmpb $36, %al - jnc lmbad - -lmuse: call mode_set - jc lmdef - -lmbad: leaw unknt, %si - call prtstr - jmp lm2 -lmscan: cmpb $0, adapter # Scanning only on EGA/VGA - jz lmbad - - movw $0, mt_end # Scanning of modes is - movb $1, scanning # done as new autodetection. - call mode_table - jmp listm0 -lmdef: ret - -# Additional parts of mode_set... (relative jumps, you know) -setv7: # Video7 extended modes - DO_STORE - subb $VIDEO_FIRST_V7>>8, %bh - movw $0x6f05, %ax - int $0x10 - stc - ret - -_setrec: jmp setrec # Ugly... -_set_80x25: jmp set_80x25 - -# Aliases for backward compatibility. -setalias: - movw $VIDEO_80x25, %ax - incw %bx - jz mode_set - - movb $VIDEO_8POINT-VIDEO_FIRST_SPECIAL, %al - incw %bx - jnz setbad # Fall-through! - -# Setting of user mode (AX=mode ID) => CF=success -mode_set: - movw %ax, %fs:(0x01fa) # Store mode for use in acpi_wakeup.S - movw %ax, %bx - cmpb $0xff, %ah - jz setalias - - testb $VIDEO_RECALC>>8, %ah - jnz _setrec - - cmpb $VIDEO_FIRST_RESOLUTION>>8, %ah - jnc setres - - cmpb $VIDEO_FIRST_SPECIAL>>8, %ah - jz setspc - - cmpb $VIDEO_FIRST_V7>>8, %ah - jz setv7 - - cmpb $VIDEO_FIRST_VESA>>8, %ah - jnc check_vesa - - orb %ah, %ah - jz setmenu - - decb %ah - jz setbios - -setbad: clc - movb $0, do_restore # The screen needn't be restored - ret - -setvesa: - DO_STORE - subb $VIDEO_FIRST_VESA>>8, %bh - movw $0x4f02, %ax # VESA BIOS mode set call - int $0x10 - cmpw $0x004f, %ax # AL=4f if implemented - jnz setbad # AH=0 if OK - - stc - ret - -setbios: - DO_STORE - int $0x10 # Standard BIOS mode set call - pushw %bx - movb $0x0f, %ah # Check if really set - int $0x10 - popw %bx - cmpb %bl, %al - jnz setbad - - stc - ret - -setspc: xorb %bh, %bh # Set special mode - cmpb $VIDEO_LAST_SPECIAL-VIDEO_FIRST_SPECIAL, %bl - jnc setbad - - addw %bx, %bx - jmp *spec_inits(%bx) - -setmenu: - orb %al, %al # 80x25 is an exception - jz _set_80x25 - - pushw %bx # Set mode chosen from menu - call mode_table # Build the mode table - popw %ax - shlw $2, %ax - addw %ax, %si - cmpw %di, %si - jnc setbad - - movw (%si), %ax # Fetch mode ID -_m_s: jmp mode_set - -setres: pushw %bx # Set mode chosen by resolution - call mode_table - popw %bx - xchgb %bl, %bh -setr1: lodsw - cmpw $ASK_VGA, %ax # End of the list? - jz setbad - - lodsw - cmpw %bx, %ax - jnz setr1 - - movw -4(%si), %ax # Fetch mode ID - jmp _m_s - -check_vesa: -#ifdef CONFIG_FIRMWARE_EDID - leaw modelist+1024, %di - movw $0x4f00, %ax - int $0x10 - cmpw $0x004f, %ax - jnz setbad - - movw 4(%di), %ax - movw %ax, vbe_version -#endif - leaw modelist+1024, %di - subb $VIDEO_FIRST_VESA>>8, %bh - movw %bx, %cx # Get mode information structure - movw $0x4f01, %ax - int $0x10 - addb $VIDEO_FIRST_VESA>>8, %bh - cmpw $0x004f, %ax - jnz setbad - - movb (%di), %al # Check capabilities. - andb $0x19, %al - cmpb $0x09, %al - jz setvesa # This is a text mode - - movb (%di), %al # Check capabilities. - andb $0x99, %al - cmpb $0x99, %al - jnz _setbad # Doh! No linear frame buffer. - - subb $VIDEO_FIRST_VESA>>8, %bh - orw $0x4000, %bx # Use linear frame buffer - movw $0x4f02, %ax # VESA BIOS mode set call - int $0x10 - cmpw $0x004f, %ax # AL=4f if implemented - jnz _setbad # AH=0 if OK - - movb $1, graphic_mode # flag graphic mode - movb $0, do_restore # no screen restore - stc - ret - -_setbad: jmp setbad # Ugly... - -# Recalculate vertical display end registers -- this fixes various -# inconsistencies of extended modes on many adapters. Called when -# the VIDEO_RECALC flag is set in the mode ID. - -setrec: subb $VIDEO_RECALC>>8, %ah # Set the base mode - call mode_set - jnc rct3 - - movw %gs:(0x485), %ax # Font size in pixels - movb %gs:(0x484), %bl # Number of rows - incb %bl - mulb %bl # Number of visible - decw %ax # scan lines - 1 - movw $0x3d4, %dx - movw %ax, %bx - movb $0x12, %al # Lower 8 bits - movb %bl, %ah - outw %ax, %dx - movb $0x07, %al # Bits 8 and 9 in the overflow register - call inidx - xchgb %al, %ah - andb $0xbd, %ah - shrb %bh - jnc rct1 - orb $0x02, %ah -rct1: shrb %bh - jnc rct2 - orb $0x40, %ah -rct2: movb $0x07, %al - outw %ax, %dx - stc -rct3: ret - -# Table of routines for setting of the special modes. -spec_inits: - .word set_80x25 - .word set_8pixel - .word set_80x43 - .word set_80x28 - .word set_current - .word set_80x30 - .word set_80x34 - .word set_80x60 - .word set_gfx - -# Set the 80x25 mode. If already set, do nothing. -set_80x25: - movw $0x5019, force_size # Override possibly broken BIOS -use_80x25: -#ifdef CONFIG_VIDEO_400_HACK - movw $0x1202, %ax # Force 400 scan lines - movb $0x30, %bl - int $0x10 -#else - movb $0x0f, %ah # Get current mode ID - int $0x10 - cmpw $0x5007, %ax # Mode 7 (80x25 mono) is the only one available - jz st80 # on CGA/MDA/HGA and is also available on EGAM - - cmpw $0x5003, %ax # Unknown mode, force 80x25 color - jnz force3 - -st80: cmpb $0, adapter # CGA/MDA/HGA => mode 3/7 is always 80x25 - jz set80 - - movb %gs:(0x0484), %al # This is EGA+ -- beware of 80x50 etc. - orb %al, %al # Some buggy BIOS'es set 0 rows - jz set80 - - cmpb $24, %al # It's hopefully correct - jz set80 -#endif /* CONFIG_VIDEO_400_HACK */ -force3: DO_STORE - movw $0x0003, %ax # Forced set - int $0x10 -set80: stc - ret - -# Set the 80x50/80x43 8-pixel mode. Simple BIOS calls. -set_8pixel: - DO_STORE - call use_80x25 # The base is 80x25 -set_8pt: - movw $0x1112, %ax # Use 8x8 font - xorb %bl, %bl - int $0x10 - movw $0x1200, %ax # Use alternate print screen - movb $0x20, %bl - int $0x10 - movw $0x1201, %ax # Turn off cursor emulation - movb $0x34, %bl - int $0x10 - movb $0x01, %ah # Define cursor scan lines 6-7 - movw $0x0607, %cx - int $0x10 -set_current: - stc - ret - -# Set the 80x28 mode. This mode works on all VGA's, because it's a standard -# 80x25 mode with 14-point fonts instead of 16-point. -set_80x28: - DO_STORE - call use_80x25 # The base is 80x25 -set14: movw $0x1111, %ax # Use 9x14 font - xorb %bl, %bl - int $0x10 - movb $0x01, %ah # Define cursor scan lines 11-12 - movw $0x0b0c, %cx - int $0x10 - stc - ret - -# Set the 80x43 mode. This mode is works on all VGA's. -# It's a 350-scanline mode with 8-pixel font. -set_80x43: - DO_STORE - movw $0x1201, %ax # Set 350 scans - movb $0x30, %bl - int $0x10 - movw $0x0003, %ax # Reset video mode - int $0x10 - jmp set_8pt # Use 8-pixel font - -# Set the 80x30 mode (all VGA's). 480 scanlines, 16-pixel font. -set_80x30: - call use_80x25 # Start with real 80x25 - DO_STORE - movw $0x3cc, %dx # Get CRTC port - inb %dx, %al - movb $0xd4, %dl - rorb %al # Mono or color? - jc set48a - - movb $0xb4, %dl -set48a: movw $0x0c11, %ax # Vertical sync end (also unlocks CR0-7) - call outidx - movw $0x0b06, %ax # Vertical total - call outidx - movw $0x3e07, %ax # (Vertical) overflow - call outidx - movw $0xea10, %ax # Vertical sync start - call outidx - movw $0xdf12, %ax # Vertical display end - call outidx - movw $0xe715, %ax # Vertical blank start - call outidx - movw $0x0416, %ax # Vertical blank end - call outidx - pushw %dx - movb $0xcc, %dl # Misc output register (read) - inb %dx, %al - movb $0xc2, %dl # (write) - andb $0x0d, %al # Preserve clock select bits and color bit - orb $0xe2, %al # Set correct sync polarity - outb %al, %dx - popw %dx - movw $0x501e, force_size - stc # That's all. - ret - -# Set the 80x34 mode (all VGA's). 480 scans, 14-pixel font. -set_80x34: - call set_80x30 # Set 480 scans - call set14 # And 14-pt font - movw $0xdb12, %ax # VGA vertical display end - movw $0x5022, force_size -setvde: call outidx - stc - ret - -# Set the 80x60 mode (all VGA's). 480 scans, 8-pixel font. -set_80x60: - call set_80x30 # Set 480 scans - call set_8pt # And 8-pt font - movw $0xdf12, %ax # VGA vertical display end - movw $0x503c, force_size - jmp setvde - -# Special hack for ThinkPad graphics -set_gfx: -#ifdef CONFIG_VIDEO_GFX_HACK - movw $VIDEO_GFX_BIOS_AX, %ax - movw $VIDEO_GFX_BIOS_BX, %bx - int $0x10 - movw $VIDEO_GFX_DUMMY_RESOLUTION, force_size - stc -#endif - ret - -#ifdef CONFIG_VIDEO_RETAIN - -# Store screen contents to temporary buffer. -store_screen: - cmpb $0, do_restore # Already stored? - jnz stsr - - testb $CAN_USE_HEAP, loadflags # Have we space for storing? - jz stsr - - pushw %ax - pushw %bx - pushw force_size # Don't force specific size - movw $0, force_size - call mode_params # Obtain params of current mode - popw force_size - movb %fs:(PARAM_VIDEO_LINES), %ah - movb %fs:(PARAM_VIDEO_COLS), %al - movw %ax, %bx # BX=dimensions - mulb %ah - movw %ax, %cx # CX=number of characters - addw %ax, %ax # Calculate image size - addw $modelist+1024+4, %ax - cmpw heap_end_ptr, %ax - jnc sts1 # Unfortunately, out of memory - - movw %fs:(PARAM_CURSOR_POS), %ax # Store mode params - leaw modelist+1024, %di - stosw - movw %bx, %ax - stosw - pushw %ds # Store the screen - movw video_segment, %ds - xorw %si, %si - rep - movsw - popw %ds - incb do_restore # Screen will be restored later -sts1: popw %bx - popw %ax -stsr: ret - -# Restore screen contents from temporary buffer. -restore_screen: - cmpb $0, do_restore # Has the screen been stored? - jz res1 - - call mode_params # Get parameters of current mode - movb %fs:(PARAM_VIDEO_LINES), %cl - movb %fs:(PARAM_VIDEO_COLS), %ch - leaw modelist+1024, %si # Screen buffer - lodsw # Set cursor position - movw %ax, %dx - cmpb %cl, %dh - jc res2 - - movb %cl, %dh - decb %dh -res2: cmpb %ch, %dl - jc res3 - - movb %ch, %dl - decb %dl -res3: movb $0x02, %ah - movb $0x00, %bh - int $0x10 - lodsw # Display size - movb %ah, %dl # DL=number of lines - movb $0, %ah # BX=phys. length of orig. line - movw %ax, %bx - cmpb %cl, %dl # Too many? - jc res4 - - pushw %ax - movb %dl, %al - subb %cl, %al - mulb %bl - addw %ax, %si - addw %ax, %si - popw %ax - movb %cl, %dl -res4: cmpb %ch, %al # Too wide? - jc res5 - - movb %ch, %al # AX=width of src. line -res5: movb $0, %cl - xchgb %ch, %cl - movw %cx, %bp # BP=width of dest. line - pushw %es - movw video_segment, %es - xorw %di, %di # Move the data - addw %bx, %bx # Convert BX and BP to _bytes_ - addw %bp, %bp -res6: pushw %si - pushw %di - movw %ax, %cx - rep - movsw - popw %di - popw %si - addw %bp, %di - addw %bx, %si - decb %dl - jnz res6 - - popw %es # Done -res1: ret -#endif /* CONFIG_VIDEO_RETAIN */ - -# Write to indexed VGA register (AL=index, AH=data, DX=index reg. port) -outidx: outb %al, %dx - pushw %ax - movb %ah, %al - incw %dx - outb %al, %dx - decw %dx - popw %ax - ret - -# Build the table of video modes (stored after the setup.S code at the -# `modelist' label. Each video mode record looks like: -# .word MODE-ID (our special mode ID (see above)) -# .byte rows (number of rows) -# .byte columns (number of columns) -# Returns address of the end of the table in DI, the end is marked -# with a ASK_VGA ID. -mode_table: - movw mt_end, %di # Already filled? - orw %di, %di - jnz mtab1x - - leaw modelist, %di # Store standard modes: - movl $VIDEO_80x25 + 0x50190000, %eax # The 80x25 mode (ALL) - stosl - movb adapter, %al # CGA/MDA/HGA -- no more modes - orb %al, %al - jz mtabe - - decb %al - jnz mtabv - - movl $VIDEO_8POINT + 0x502b0000, %eax # The 80x43 EGA mode - stosl - jmp mtabe - -mtab1x: jmp mtab1 - -mtabv: leaw vga_modes, %si # All modes for std VGA - movw $vga_modes_end-vga_modes, %cx - rep # I'm unable to use movsw as I don't know how to store a half - movsb # of the expression above to cx without using explicit shr. - - cmpb $0, scanning # Mode scan requested? - jz mscan1 - - call mode_scan -mscan1: - -#ifdef CONFIG_VIDEO_LOCAL - call local_modes -#endif /* CONFIG_VIDEO_LOCAL */ - -#ifdef CONFIG_VIDEO_VESA - call vesa_modes # Detect VESA VGA modes -#endif /* CONFIG_VIDEO_VESA */ - -#ifdef CONFIG_VIDEO_SVGA - cmpb $0, scanning # Bypass when scanning - jnz mscan2 - - call svga_modes # Detect SVGA cards & modes -mscan2: -#endif /* CONFIG_VIDEO_SVGA */ - -mtabe: - -#ifdef CONFIG_VIDEO_COMPACT - leaw modelist, %si - movw %di, %dx - movw %si, %di -cmt1: cmpw %dx, %si # Scan all modes - jz cmt2 - - leaw modelist, %bx # Find in previous entries - movw 2(%si), %cx -cmt3: cmpw %bx, %si - jz cmt4 - - cmpw 2(%bx), %cx # Found => don't copy this entry - jz cmt5 - - addw $4, %bx - jmp cmt3 - -cmt4: movsl # Copy entry - jmp cmt1 - -cmt5: addw $4, %si # Skip entry - jmp cmt1 - -cmt2: -#endif /* CONFIG_VIDEO_COMPACT */ - - movw $ASK_VGA, (%di) # End marker - movw %di, mt_end -mtab1: leaw modelist, %si # SI=mode list, DI=list end -ret0: ret - -# Modes usable on all standard VGAs -vga_modes: - .word VIDEO_8POINT - .word 0x5032 # 80x50 - .word VIDEO_80x43 - .word 0x502b # 80x43 - .word VIDEO_80x28 - .word 0x501c # 80x28 - .word VIDEO_80x30 - .word 0x501e # 80x30 - .word VIDEO_80x34 - .word 0x5022 # 80x34 - .word VIDEO_80x60 - .word 0x503c # 80x60 -#ifdef CONFIG_VIDEO_GFX_HACK - .word VIDEO_GFX_HACK - .word VIDEO_GFX_DUMMY_RESOLUTION -#endif - -vga_modes_end: -# Detect VESA modes. - -#ifdef CONFIG_VIDEO_VESA -vesa_modes: - cmpb $2, adapter # VGA only - jnz ret0 - - movw %di, %bp # BP=original mode table end - addw $0x200, %di # Buffer space - movw $0x4f00, %ax # VESA Get card info call - int $0x10 - movw %bp, %di - cmpw $0x004f, %ax # Successful? - jnz ret0 - - cmpw $0x4556, 0x200(%di) - jnz ret0 - - cmpw $0x4153, 0x202(%di) - jnz ret0 - - movw $vesa_name, card_name # Set name to "VESA VGA" - pushw %gs - lgsw 0x20e(%di), %si # GS:SI=mode list - movw $128, %cx # Iteration limit -vesa1: -# gas version 2.9.1, using BFD version 2.9.1.0.23 buggers the next inst. -# XXX: lodsw %gs:(%si), %ax # Get next mode in the list - gs; lodsw - cmpw $0xffff, %ax # End of the table? - jz vesar - - cmpw $0x0080, %ax # Check validity of mode ID - jc vesa2 - - orb %ah, %ah # Valid IDs: 0x0000-0x007f/0x0100-0x07ff - jz vesan # Certain BIOSes report 0x80-0xff! - - cmpw $0x0800, %ax - jnc vesae - -vesa2: pushw %cx - movw %ax, %cx # Get mode information structure - movw $0x4f01, %ax - int $0x10 - movw %cx, %bx # BX=mode number - addb $VIDEO_FIRST_VESA>>8, %bh - popw %cx - cmpw $0x004f, %ax - jnz vesan # Don't report errors (buggy BIOSES) - - movb (%di), %al # Check capabilities. We require - andb $0x19, %al # a color text mode. - cmpb $0x09, %al - jnz vesan - - cmpw $0xb800, 8(%di) # Standard video memory address required - jnz vesan - - testb $2, (%di) # Mode characteristics supplied? - movw %bx, (%di) # Store mode number - jz vesa3 - - xorw %dx, %dx - movw 0x12(%di), %bx # Width - orb %bh, %bh - jnz vesan - - movb %bl, 0x3(%di) - movw 0x14(%di), %ax # Height - orb %ah, %ah - jnz vesan - - movb %al, 2(%di) - mulb %bl - cmpw $8193, %ax # Small enough for Linux console driver? - jnc vesan - - jmp vesaok - -vesa3: subw $0x8108, %bx # This mode has no detailed info specified, - jc vesan # so it must be a standard VESA mode. - - cmpw $5, %bx - jnc vesan - - movw vesa_text_mode_table(%bx), %ax - movw %ax, 2(%di) -vesaok: addw $4, %di # The mode is valid. Store it. -vesan: loop vesa1 # Next mode. Limit exceeded => error -vesae: leaw vesaer, %si - call prtstr - movw %bp, %di # Discard already found modes. -vesar: popw %gs - ret - -# Dimensions of standard VESA text modes -vesa_text_mode_table: - .byte 60, 80 # 0108 - .byte 25, 132 # 0109 - .byte 43, 132 # 010A - .byte 50, 132 # 010B - .byte 60, 132 # 010C -#endif /* CONFIG_VIDEO_VESA */ - -# Scan for video modes. A bit dirty, but should work. -mode_scan: - movw $0x0100, %cx # Start with mode 0 -scm1: movb $0, %ah # Test the mode - movb %cl, %al - int $0x10 - movb $0x0f, %ah - int $0x10 - cmpb %cl, %al - jnz scm2 # Mode not set - - movw $0x3c0, %dx # Test if it's a text mode - movb $0x10, %al # Mode bits - call inidx - andb $0x03, %al - jnz scm2 - - movb $0xce, %dl # Another set of mode bits - movb $0x06, %al - call inidx - shrb %al - jc scm2 - - movb $0xd4, %dl # Cursor location - movb $0x0f, %al - call inidx - orb %al, %al - jnz scm2 - - movw %cx, %ax # Ok, store the mode - stosw - movb %gs:(0x484), %al # Number of rows - incb %al - stosb - movw %gs:(0x44a), %ax # Number of columns - stosb -scm2: incb %cl - jns scm1 - - movw $0x0003, %ax # Return back to mode 3 - int $0x10 - ret - -tstidx: outw %ax, %dx # OUT DX,AX and inidx -inidx: outb %al, %dx # Read from indexed VGA register - incw %dx # AL=index, DX=index reg port -> AL=data - inb %dx, %al - decw %dx - ret - -# Try to detect type of SVGA card and supply (usually approximate) video -# mode table for it. - -#ifdef CONFIG_VIDEO_SVGA -svga_modes: - leaw svga_table, %si # Test all known SVGA adapters -dosvga: lodsw - movw %ax, %bp # Default mode table - orw %ax, %ax - jz didsv1 - - lodsw # Pointer to test routine - pushw %si - pushw %di - pushw %es - movw $0xc000, %bx - movw %bx, %es - call *%ax # Call test routine - popw %es - popw %di - popw %si - orw %bp, %bp - jz dosvga - - movw %bp, %si # Found, copy the modes - movb svga_prefix, %ah -cpsvga: lodsb - orb %al, %al - jz didsv - - stosw - movsw - jmp cpsvga - -didsv: movw %si, card_name # Store pointer to card name -didsv1: ret - -# Table of all known SVGA cards. For each card, we store a pointer to -# a table of video modes supported by the card and a pointer to a routine -# used for testing of presence of the card. The video mode table is always -# followed by the name of the card or the chipset. -svga_table: - .word ati_md, ati_test - .word oak_md, oak_test - .word paradise_md, paradise_test - .word realtek_md, realtek_test - .word s3_md, s3_test - .word chips_md, chips_test - .word video7_md, video7_test - .word cirrus5_md, cirrus5_test - .word cirrus6_md, cirrus6_test - .word cirrus1_md, cirrus1_test - .word ahead_md, ahead_test - .word everex_md, everex_test - .word genoa_md, genoa_test - .word trident_md, trident_test - .word tseng_md, tseng_test - .word 0 - -# Test routines and mode tables: - -# S3 - The test algorithm was taken from the SuperProbe package -# for XFree86 1.2.1. Report bugs to Christoph.Niemann@linux.org -s3_test: - movw $0x0f35, %cx # we store some constants in cl/ch - movw $0x03d4, %dx - movb $0x38, %al - call inidx - movb %al, %bh # store current CRT-register 0x38 - movw $0x0038, %ax - call outidx # disable writing to special regs - movb %cl, %al # check whether we can write special reg 0x35 - call inidx - movb %al, %bl # save the current value of CRT reg 0x35 - andb $0xf0, %al # clear bits 0-3 - movb %al, %ah - movb %cl, %al # and write it to CRT reg 0x35 - call outidx - call inidx # now read it back - andb %ch, %al # clear the upper 4 bits - jz s3_2 # the first test failed. But we have a - - movb %bl, %ah # second chance - movb %cl, %al - call outidx - jmp s3_1 # do the other tests - -s3_2: movw %cx, %ax # load ah with 0xf and al with 0x35 - orb %bl, %ah # set the upper 4 bits of ah with the orig value - call outidx # write ... - call inidx # ... and reread - andb %cl, %al # turn off the upper 4 bits - pushw %ax - movb %bl, %ah # restore old value in register 0x35 - movb %cl, %al - call outidx - popw %ax - cmpb %ch, %al # setting lower 4 bits was successful => bad - je no_s3 # writing is allowed => this is not an S3 - -s3_1: movw $0x4838, %ax # allow writing to special regs by putting - call outidx # magic number into CRT-register 0x38 - movb %cl, %al # check whether we can write special reg 0x35 - call inidx - movb %al, %bl - andb $0xf0, %al - movb %al, %ah - movb %cl, %al - call outidx - call inidx - andb %ch, %al - jnz no_s3 # no, we can't write => no S3 - - movw %cx, %ax - orb %bl, %ah - call outidx - call inidx - andb %ch, %al - pushw %ax - movb %bl, %ah # restore old value in register 0x35 - movb %cl, %al - call outidx - popw %ax - cmpb %ch, %al - jne no_s31 # writing not possible => no S3 - movb $0x30, %al - call inidx # now get the S3 id ... - leaw idS3, %di - movw $0x10, %cx - repne - scasb - je no_s31 - - movb %bh, %ah - movb $0x38, %al - jmp s3rest - -no_s3: movb $0x35, %al # restore CRT register 0x35 - movb %bl, %ah - call outidx -no_s31: xorw %bp, %bp # Detection failed -s3rest: movb %bh, %ah - movb $0x38, %al # restore old value of CRT register 0x38 - jmp outidx - -idS3: .byte 0x81, 0x82, 0x90, 0x91, 0x92, 0x93, 0x94, 0x95 - .byte 0xa0, 0xa1, 0xa2, 0xa3, 0xa4, 0xa5, 0xa8, 0xb0 - -s3_md: .byte 0x54, 0x2b, 0x84 - .byte 0x55, 0x19, 0x84 - .byte 0 - .ascii "S3" - .byte 0 - -# ATI cards. -ati_test: - leaw idati, %si - movw $0x31, %di - movw $0x09, %cx - repe - cmpsb - je atiok - - xorw %bp, %bp -atiok: ret - -idati: .ascii "761295520" - -ati_md: .byte 0x23, 0x19, 0x84 - .byte 0x33, 0x2c, 0x84 - .byte 0x22, 0x1e, 0x64 - .byte 0x21, 0x19, 0x64 - .byte 0x58, 0x21, 0x50 - .byte 0x5b, 0x1e, 0x50 - .byte 0 - .ascii "ATI" - .byte 0 - -# AHEAD -ahead_test: - movw $0x200f, %ax - movw $0x3ce, %dx - outw %ax, %dx - incw %dx - inb %dx, %al - cmpb $0x20, %al - je isahed - - cmpb $0x21, %al - je isahed - - xorw %bp, %bp -isahed: ret - -ahead_md: - .byte 0x22, 0x2c, 0x84 - .byte 0x23, 0x19, 0x84 - .byte 0x24, 0x1c, 0x84 - .byte 0x2f, 0x32, 0xa0 - .byte 0x32, 0x22, 0x50 - .byte 0x34, 0x42, 0x50 - .byte 0 - .ascii "Ahead" - .byte 0 - -# Chips & Tech. -chips_test: - movw $0x3c3, %dx - inb %dx, %al - orb $0x10, %al - outb %al, %dx - movw $0x104, %dx - inb %dx, %al - movb %al, %bl - movw $0x3c3, %dx - inb %dx, %al - andb $0xef, %al - outb %al, %dx - cmpb $0xa5, %bl - je cantok - - xorw %bp, %bp -cantok: ret - -chips_md: - .byte 0x60, 0x19, 0x84 - .byte 0x61, 0x32, 0x84 - .byte 0 - .ascii "Chips & Technologies" - .byte 0 - -# Cirrus Logic 5X0 -cirrus1_test: - movw $0x3d4, %dx - movb $0x0c, %al - outb %al, %dx - incw %dx - inb %dx, %al - movb %al, %bl - xorb %al, %al - outb %al, %dx - decw %dx - movb $0x1f, %al - outb %al, %dx - incw %dx - inb %dx, %al - movb %al, %bh - xorb %ah, %ah - shlb $4, %al - movw %ax, %cx - movb %bh, %al - shrb $4, %al - addw %ax, %cx - shlw $8, %cx - addw $6, %cx - movw %cx, %ax - movw $0x3c4, %dx - outw %ax, %dx - incw %dx - inb %dx, %al - andb %al, %al - jnz nocirr - - movb %bh, %al - outb %al, %dx - inb %dx, %al - cmpb $0x01, %al - je iscirr - -nocirr: xorw %bp, %bp -iscirr: movw $0x3d4, %dx - movb %bl, %al - xorb %ah, %ah - shlw $8, %ax - addw $0x0c, %ax - outw %ax, %dx - ret - -cirrus1_md: - .byte 0x1f, 0x19, 0x84 - .byte 0x20, 0x2c, 0x84 - .byte 0x22, 0x1e, 0x84 - .byte 0x31, 0x25, 0x64 - .byte 0 - .ascii "Cirrus Logic 5X0" - .byte 0 - -# Cirrus Logic 54XX -cirrus5_test: - movw $0x3c4, %dx - movb $6, %al - call inidx - movb %al, %bl # BL=backup - movw $6, %ax - call tstidx - cmpb $0x0f, %al - jne c5fail - - movw $0x1206, %ax - call tstidx - cmpb $0x12, %al - jne c5fail - - movb $0x1e, %al - call inidx - movb %al, %bh - movb %bh, %ah - andb $0xc0, %ah - movb $0x1e, %al - call tstidx - andb $0x3f, %al - jne c5xx - - movb $0x1e, %al - movb %bh, %ah - orb $0x3f, %ah - call tstidx - xorb $0x3f, %al - andb $0x3f, %al -c5xx: pushf - movb $0x1e, %al - movb %bh, %ah - outw %ax, %dx - popf - je c5done - -c5fail: xorw %bp, %bp -c5done: movb $6, %al - movb %bl, %ah - outw %ax, %dx - ret - -cirrus5_md: - .byte 0x14, 0x19, 0x84 - .byte 0x54, 0x2b, 0x84 - .byte 0 - .ascii "Cirrus Logic 54XX" - .byte 0 - -# Cirrus Logic 64XX -- no known extra modes, but must be identified, because -# it's misidentified by the Ahead test. -cirrus6_test: - movw $0x3ce, %dx - movb $0x0a, %al - call inidx - movb %al, %bl # BL=backup - movw $0xce0a, %ax - call tstidx - orb %al, %al - jne c2fail - - movw $0xec0a, %ax - call tstidx - cmpb $0x01, %al - jne c2fail - - movb $0xaa, %al - call inidx # 4X, 5X, 7X and 8X are valid 64XX chip ID's. - shrb $4, %al - subb $4, %al - jz c6done - - decb %al - jz c6done - - subb $2, %al - jz c6done - - decb %al - jz c6done - -c2fail: xorw %bp, %bp -c6done: movb $0x0a, %al - movb %bl, %ah - outw %ax, %dx - ret - -cirrus6_md: - .byte 0 - .ascii "Cirrus Logic 64XX" - .byte 0 - -# Everex / Trident -everex_test: - movw $0x7000, %ax - xorw %bx, %bx - int $0x10 - cmpb $0x70, %al - jne noevrx - - shrw $4, %dx - cmpw $0x678, %dx - je evtrid - - cmpw $0x236, %dx - jne evrxok - -evtrid: leaw trident_md, %bp -evrxok: ret - -noevrx: xorw %bp, %bp - ret - -everex_md: - .byte 0x03, 0x22, 0x50 - .byte 0x04, 0x3c, 0x50 - .byte 0x07, 0x2b, 0x64 - .byte 0x08, 0x4b, 0x64 - .byte 0x0a, 0x19, 0x84 - .byte 0x0b, 0x2c, 0x84 - .byte 0x16, 0x1e, 0x50 - .byte 0x18, 0x1b, 0x64 - .byte 0x21, 0x40, 0xa0 - .byte 0x40, 0x1e, 0x84 - .byte 0 - .ascii "Everex/Trident" - .byte 0 - -# Genoa. -genoa_test: - leaw idgenoa, %si # Check Genoa 'clues' - xorw %ax, %ax - movb %es:(0x37), %al - movw %ax, %di - movw $0x04, %cx - decw %si - decw %di -l1: incw %si - incw %di - movb (%si), %al - testb %al, %al - jz l2 - - cmpb %es:(%di), %al -l2: loope l1 - orw %cx, %cx - je isgen - - xorw %bp, %bp -isgen: ret - -idgenoa: .byte 0x77, 0x00, 0x99, 0x66 - -genoa_md: - .byte 0x58, 0x20, 0x50 - .byte 0x5a, 0x2a, 0x64 - .byte 0x60, 0x19, 0x84 - .byte 0x61, 0x1d, 0x84 - .byte 0x62, 0x20, 0x84 - .byte 0x63, 0x2c, 0x84 - .byte 0x64, 0x3c, 0x84 - .byte 0x6b, 0x4f, 0x64 - .byte 0x72, 0x3c, 0x50 - .byte 0x74, 0x42, 0x50 - .byte 0x78, 0x4b, 0x64 - .byte 0 - .ascii "Genoa" - .byte 0 - -# OAK -oak_test: - leaw idoakvga, %si - movw $0x08, %di - movw $0x08, %cx - repe - cmpsb - je isoak - - xorw %bp, %bp -isoak: ret - -idoakvga: .ascii "OAK VGA " - -oak_md: .byte 0x4e, 0x3c, 0x50 - .byte 0x4f, 0x3c, 0x84 - .byte 0x50, 0x19, 0x84 - .byte 0x51, 0x2b, 0x84 - .byte 0 - .ascii "OAK" - .byte 0 - -# WD Paradise. -paradise_test: - leaw idparadise, %si - movw $0x7d, %di - movw $0x04, %cx - repe - cmpsb - je ispara - - xorw %bp, %bp -ispara: ret - -idparadise: .ascii "VGA=" - -paradise_md: - .byte 0x41, 0x22, 0x50 - .byte 0x47, 0x1c, 0x84 - .byte 0x55, 0x19, 0x84 - .byte 0x54, 0x2c, 0x84 - .byte 0 - .ascii "Paradise" - .byte 0 - -# Trident. -trident_test: - movw $0x3c4, %dx - movb $0x0e, %al - outb %al, %dx - incw %dx - inb %dx, %al - xchgb %al, %ah - xorb %al, %al - outb %al, %dx - inb %dx, %al - xchgb %ah, %al - movb %al, %bl # Strange thing ... in the book this wasn't - andb $0x02, %bl # necessary but it worked on my card which - jz setb2 # is a trident. Without it the screen goes - # blurred ... - andb $0xfd, %al - jmp clrb2 - -setb2: orb $0x02, %al -clrb2: outb %al, %dx - andb $0x0f, %ah - cmpb $0x02, %ah - je istrid - - xorw %bp, %bp -istrid: ret - -trident_md: - .byte 0x50, 0x1e, 0x50 - .byte 0x51, 0x2b, 0x50 - .byte 0x52, 0x3c, 0x50 - .byte 0x57, 0x19, 0x84 - .byte 0x58, 0x1e, 0x84 - .byte 0x59, 0x2b, 0x84 - .byte 0x5a, 0x3c, 0x84 - .byte 0 - .ascii "Trident" - .byte 0 - -# Tseng. -tseng_test: - movw $0x3cd, %dx - inb %dx, %al # Could things be this simple ! :-) - movb %al, %bl - movb $0x55, %al - outb %al, %dx - inb %dx, %al - movb %al, %ah - movb %bl, %al - outb %al, %dx - cmpb $0x55, %ah - je istsen - -isnot: xorw %bp, %bp -istsen: ret - -tseng_md: - .byte 0x26, 0x3c, 0x50 - .byte 0x2a, 0x28, 0x64 - .byte 0x23, 0x19, 0x84 - .byte 0x24, 0x1c, 0x84 - .byte 0x22, 0x2c, 0x84 - .byte 0x21, 0x3c, 0x84 - .byte 0 - .ascii "Tseng" - .byte 0 - -# Video7. -video7_test: - movw $0x3cc, %dx - inb %dx, %al - movw $0x3b4, %dx - andb $0x01, %al - jz even7 - - movw $0x3d4, %dx -even7: movb $0x0c, %al - outb %al, %dx - incw %dx - inb %dx, %al - movb %al, %bl - movb $0x55, %al - outb %al, %dx - inb %dx, %al - decw %dx - movb $0x1f, %al - outb %al, %dx - incw %dx - inb %dx, %al - movb %al, %bh - decw %dx - movb $0x0c, %al - outb %al, %dx - incw %dx - movb %bl, %al - outb %al, %dx - movb $0x55, %al - xorb $0xea, %al - cmpb %bh, %al - jne isnot - - movb $VIDEO_FIRST_V7>>8, svga_prefix # Use special mode switching - ret - -video7_md: - .byte 0x40, 0x2b, 0x50 - .byte 0x43, 0x3c, 0x50 - .byte 0x44, 0x3c, 0x64 - .byte 0x41, 0x19, 0x84 - .byte 0x42, 0x2c, 0x84 - .byte 0x45, 0x1c, 0x84 - .byte 0 - .ascii "Video 7" - .byte 0 - -# Realtek VGA -realtek_test: - leaw idrtvga, %si - movw $0x45, %di - movw $0x0b, %cx - repe - cmpsb - je isrt - - xorw %bp, %bp -isrt: ret - -idrtvga: .ascii "REALTEK VGA" - -realtek_md: - .byte 0x1a, 0x3c, 0x50 - .byte 0x1b, 0x19, 0x84 - .byte 0x1c, 0x1e, 0x84 - .byte 0x1d, 0x2b, 0x84 - .byte 0x1e, 0x3c, 0x84 - .byte 0 - .ascii "REALTEK" - .byte 0 - -#endif /* CONFIG_VIDEO_SVGA */ - -# User-defined local mode table (VGA only) -#ifdef CONFIG_VIDEO_LOCAL -local_modes: - leaw local_mode_table, %si -locm1: lodsw - orw %ax, %ax - jz locm2 - - stosw - movsw - jmp locm1 - -locm2: ret - -# This is the table of local video modes which can be supplied manually -# by the user. Each entry consists of mode ID (word) and dimensions -# (byte for column count and another byte for row count). These modes -# are placed before all SVGA and VESA modes and override them if table -# compacting is enabled. The table must end with a zero word followed -# by NUL-terminated video adapter name. -local_mode_table: - .word 0x0100 # Example: 40x25 - .byte 25,40 - .word 0 - .ascii "Local" - .byte 0 -#endif /* CONFIG_VIDEO_LOCAL */ - -# Read a key and return the ASCII code in al, scan code in ah -getkey: xorb %ah, %ah - int $0x16 - ret - -# Read a key with a timeout of 30 seconds. -# The hardware clock is used to get the time. -getkt: call gettime - addb $30, %al # Wait 30 seconds - cmpb $60, %al - jl lminute - - subb $60, %al -lminute: - movb %al, %cl -again: movb $0x01, %ah - int $0x16 - jnz getkey # key pressed, so get it - - call gettime - cmpb %cl, %al - jne again - - movb $0x20, %al # timeout, return `space' - ret - -# Flush the keyboard buffer -flush: movb $0x01, %ah - int $0x16 - jz empty - - xorb %ah, %ah - int $0x16 - jmp flush - -empty: ret - -# Print hexadecimal number. -prthw: pushw %ax - movb %ah, %al - call prthb - popw %ax -prthb: pushw %ax - shrb $4, %al - call prthn - popw %ax - andb $0x0f, %al -prthn: cmpb $0x0a, %al - jc prth1 - - addb $0x07, %al -prth1: addb $0x30, %al - jmp prtchr - -# Print decimal number in al -prtdec: pushw %ax - pushw %cx - xorb %ah, %ah - movb $0x0a, %cl - idivb %cl - cmpb $0x09, %al - jbe lt100 - - call prtdec - jmp skip10 - -lt100: addb $0x30, %al - call prtchr -skip10: movb %ah, %al - addb $0x30, %al - call prtchr - popw %cx - popw %ax - ret - -store_edid: -#ifdef CONFIG_FIRMWARE_EDID - pushw %es # just save all registers - pushw %ax - pushw %bx - pushw %cx - pushw %dx - pushw %di - - pushw %fs - popw %es - - movl $0x13131313, %eax # memset block with 0x13 - movw $32, %cx - movw $0x140, %di - cld - rep - stosl - - cmpw $0x0200, vbe_version # only do EDID on >= VBE2.0 - jl no_edid - - pushw %es # save ES - xorw %di, %di # Report Capability - pushw %di - popw %es # ES:DI must be 0:0 - movw $0x4f15, %ax - xorw %bx, %bx - xorw %cx, %cx - int $0x10 - popw %es # restore ES - - cmpb $0x00, %ah # call successful - jne no_edid - - cmpb $0x4f, %al # function supported - jne no_edid - - movw $0x4f15, %ax # do VBE/DDC - movw $0x01, %bx - movw $0x00, %cx - movw $0x00, %dx - movw $0x140, %di - int $0x10 - -no_edid: - popw %di # restore all registers - popw %dx - popw %cx - popw %bx - popw %ax - popw %es -#endif - ret - -# VIDEO_SELECT-only variables -mt_end: .word 0 # End of video mode table if built -edit_buf: .space 6 # Line editor buffer -card_name: .word 0 # Pointer to adapter name -scanning: .byte 0 # Performing mode scan -do_restore: .byte 0 # Screen contents altered during mode change -svga_prefix: .byte VIDEO_FIRST_BIOS>>8 # Default prefix for BIOS modes -graphic_mode: .byte 0 # Graphic mode with a linear frame buffer -dac_size: .byte 6 # DAC bit depth -vbe_version: .word 0 # VBE bios version - -# Status messages -keymsg: .ascii "Press to see video modes available, " - .ascii " to continue or wait 30 secs" - .byte 0x0d, 0x0a, 0 - -listhdr: .byte 0x0d, 0x0a - .ascii "Mode: COLSxROWS:" - -crlft: .byte 0x0d, 0x0a, 0 - -prompt: .byte 0x0d, 0x0a - .asciz "Enter mode number or `scan': " - -unknt: .asciz "Unknown mode ID. Try again." - -badmdt: .ascii "You passed an undefined mode number." - .byte 0x0d, 0x0a, 0 - -vesaer: .ascii "Error: Scanning of VESA modes failed. Please " - .ascii "report to ." - .byte 0x0d, 0x0a, 0 - -old_name: .asciz "CGA/MDA/HGA" - -ega_name: .asciz "EGA" - -svga_name: .ascii " " - -vga_name: .asciz "VGA" - -vesa_name: .asciz "VESA" - -name_bann: .asciz "Video adapter: " -#endif /* CONFIG_VIDEO_SELECT */ - -# Other variables: -adapter: .byte 0 # Video adapter: 0=CGA/MDA/HGA,1=EGA,2=VGA -video_segment: .word 0xb800 # Video memory segment -force_size: .word 0 # Use this size instead of the one in BIOS vars diff --git a/arch/i386/kernel/verify_cpu.S b/arch/i386/kernel/verify_cpu.S deleted file mode 100644 index fff4aa61d7..0000000000 --- a/arch/i386/kernel/verify_cpu.S +++ /dev/null @@ -1,94 +0,0 @@ -/* Check if CPU has some minimum CPUID bits - This runs in 16bit mode so that the caller can still use the BIOS - to output errors on the screen */ -#include -#include - -verify_cpu: - pushfl # Save caller passed flags - pushl $0 # Kill any dangerous flags - popfl - -#if CONFIG_X86_MINIMUM_CPU_FAMILY >= 4 - pushfl - pop %eax - orl $(1<<18),%eax # try setting AC - push %eax - popfl - pushfl - popl %eax - testl $(1<<18),%eax - jz bad -#endif -#if REQUIRED_MASK0 != 0 - pushfl # standard way to check for cpuid - popl %eax - movl %eax,%ebx - xorl $0x200000,%eax - pushl %eax - popfl - pushfl - popl %eax - cmpl %eax,%ebx - pushfl # standard way to check for cpuid - popl %eax - movl %eax,%ebx - xorl $0x200000,%eax - pushl %eax - popfl - pushfl - popl %eax - cmpl %eax,%ebx - jz bad # REQUIRED_MASK0 != 0 requires CPUID - - movl $0x0,%eax # See if cpuid 1 is implemented - cpuid - cmpl $0x1,%eax - jb bad # no cpuid 1 - -#if REQUIRED_MASK0 & NEED_CMPXCHG64 - /* Some VIA C3s need magic MSRs to enable CX64. Do this here */ - cmpl $0x746e6543,%ebx # Cent - jne 1f - cmpl $0x48727561,%edx # aurH - jne 1f - cmpl $0x736c7561,%ecx # auls - jne 1f - movl $1,%eax # check model - cpuid - movl %eax,%ebx - shr $8,%ebx - andl $0xf,%ebx - cmp $6,%ebx # check family == 6 - jne 1f - shr $4,%eax - andl $0xf,%eax - cmpl $6,%eax # check model >= 6 - jb 1f - # assume models >= 6 all support this MSR - movl $MSR_VIA_FCR,%ecx - rdmsr - orl $((1<<1)|(1<<7)),%eax # enable CMPXCHG64 and PGE - wrmsr -1: -#endif - movl $0x1,%eax # Does the cpu have what it takes - cpuid - -#if CONFIG_X86_MINIMUM_CPU_FAMILY > 4 -#error add proper model checking here -#endif - - andl $REQUIRED_MASK0,%edx - xorl $REQUIRED_MASK0,%edx - jnz bad -#endif /* REQUIRED_MASK0 */ - - popfl - xor %eax,%eax - ret - -bad: - popfl - movl $1,%eax - ret diff --git a/include/linux/edd.h b/include/linux/edd.h index b2b3e68aa5..7b647822d6 100644 --- a/include/linux/edd.h +++ b/include/linux/edd.h @@ -49,10 +49,6 @@ #define EDD_MBR_SIG_MAX 16 /* max number of signatures to store */ #define EDD_MBR_SIG_NR_BUF 0x1ea /* addr of number of MBR signtaures at EDD_MBR_SIG_BUF in boot_params - treat this as 1 byte */ -#define EDD_CL_EQUALS 0x3d646465 /* "edd=" */ -#define EDD_CL_OFF 0x666f /* "of" for off */ -#define EDD_CL_SKIP 0x6b73 /* "sk" for skipmbr */ -#define EDD_CL_ON 0x6e6f /* "on" for on */ #ifndef __ASSEMBLY__