From: Evgeniy Polyakov Date: Tue, 6 Dec 2005 10:38:28 +0000 (+0300) Subject: [PATCH] W1: Add the DS2482 I2C-to-w1 bridge driver. X-Git-Tag: v2.6.17-rc1~990 X-Git-Url: https://err.no/cgi-bin/gitweb.cgi?a=commitdiff_plain;h=baf12ae29ab4cc6381e21b2e1a3af75a6a8f7566;p=linux-2.6 [PATCH] W1: Add the DS2482 I2C-to-w1 bridge driver. Signed-off-by: Ben Gardner Signed-off-by: Evgeniy Polyakov Signed-off-by: Greg Kroah-Hartman --- diff --git a/Documentation/w1/masters/ds2482 b/Documentation/w1/masters/ds2482 new file mode 100644 index 0000000000..c5d5478d90 --- /dev/null +++ b/Documentation/w1/masters/ds2482 @@ -0,0 +1,31 @@ +Kernel driver ds2482 +==================== + +Supported chips: + * Maxim DS2482-100, Maxim DS2482-800 + Prefix: 'ds2482' + Addresses scanned: None + Datasheets: + http://pdfserv.maxim-ic.com/en/ds/DS2482-100-DS2482S-100.pdf + http://pdfserv.maxim-ic.com/en/ds/DS2482-800-DS2482S-800.pdf + +Author: Ben Gardner + + +Description +----------- + +The Maixm/Dallas Semiconductor DS2482 is a I2C device that provides +one (DS2482-100) or eight (DS2482-800) 1-wire busses. + + +General Remarks +--------------- + +Valid addresses are 0x18, 0x19, 0x1a, and 0x1b. +However, the device cannot be detected without writing to the i2c bus, so no +detection is done. +You should force the device address. + +$ modprobe ds2482 force=0,0x18 + diff --git a/drivers/w1/masters/Kconfig b/drivers/w1/masters/Kconfig index 51bd64d0e5..1ff11b5a3a 100644 --- a/drivers/w1/masters/Kconfig +++ b/drivers/w1/masters/Kconfig @@ -34,5 +34,15 @@ config W1_MASTER_DS9490_BRIDGE This support is also available as a module. If so, the module will be called ds_w1_bridge.ko. +config W1_MASTER_DS2482 + tristate "Maxim DS2482 I2C to 1-Wire bridge" + depends on I2C && W1 && EXPERIMENTAL + help + If you say yes here you get support for the Maxim DS2482 + I2C to 1-Wire bridge. + + This driver can also be built as a module. If so, the module + will be called ds2482. + endmenu diff --git a/drivers/w1/masters/Makefile b/drivers/w1/masters/Makefile index d9b84e522d..1f3c8b983d 100644 --- a/drivers/w1/masters/Makefile +++ b/drivers/w1/masters/Makefile @@ -9,3 +9,5 @@ ds9490r-objs := dscore.o obj-$(CONFIG_W1_MASTER_DS9490_BRIDGE) += ds_w1_bridge.o +obj-$(CONFIG_W1_MASTER_DS2482) += ds2482.o + diff --git a/drivers/w1/masters/ds2482.c b/drivers/w1/masters/ds2482.c new file mode 100644 index 0000000000..d1cacd2357 --- /dev/null +++ b/drivers/w1/masters/ds2482.c @@ -0,0 +1,564 @@ +/** + * ds2482.c - provides i2c to w1-master bridge(s) + * Copyright (C) 2005 Ben Gardner + * + * The DS2482 is a sensor chip made by Dallas Semiconductor (Maxim). + * It is a I2C to 1-wire bridge. + * There are two variations: -100 and -800, which have 1 or 8 1-wire ports. + * The complete datasheet can be obtained from MAXIM's website at: + * http://www.maxim-ic.com/quick_view2.cfm/qv_pk/4382 + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; version 2 of the License. + */ + +#include +#include +#include +#include +#include +#include + +#include "../w1.h" +#include "../w1_int.h" + +/** + * Address is selected using 2 pins, resulting in 4 possible addresses. + * 0x18, 0x19, 0x1a, 0x1b + * However, the chip cannot be detected without doing an i2c write, + * so use the force module parameter. + */ +static unsigned short normal_i2c[] = {I2C_CLIENT_END}; + +/** + * Insmod parameters + */ +I2C_CLIENT_INSMOD_1(ds2482); + +/** + * The DS2482 registers - there are 3 registers that are addressed by a read + * pointer. The read pointer is set by the last command executed. + * + * To read the data, issue a register read for any address + */ +#define DS2482_CMD_RESET 0xF0 /* No param */ +#define DS2482_CMD_SET_READ_PTR 0xE1 /* Param: DS2482_PTR_CODE_xxx */ +#define DS2482_CMD_CHANNEL_SELECT 0xC3 /* Param: Channel byte - DS2482-800 only */ +#define DS2482_CMD_WRITE_CONFIG 0xD2 /* Param: Config byte */ +#define DS2482_CMD_1WIRE_RESET 0xB4 /* Param: None */ +#define DS2482_CMD_1WIRE_SINGLE_BIT 0x87 /* Param: Bit byte (bit7) */ +#define DS2482_CMD_1WIRE_WRITE_BYTE 0xA5 /* Param: Data byte */ +#define DS2482_CMD_1WIRE_READ_BYTE 0x96 /* Param: None */ +/* Note to read the byte, Set the ReadPtr to Data then read (any addr) */ +#define DS2482_CMD_1WIRE_TRIPLET 0x78 /* Param: Dir byte (bit7) */ + +/* Values for DS2482_CMD_SET_READ_PTR */ +#define DS2482_PTR_CODE_STATUS 0xF0 +#define DS2482_PTR_CODE_DATA 0xE1 +#define DS2482_PTR_CODE_CHANNEL 0xD2 /* DS2482-800 only */ +#define DS2482_PTR_CODE_CONFIG 0xC3 + +/** + * Configure Register bit definitions + * The top 4 bits always read 0. + * To write, the top nibble must be the 1's compl. of the low nibble. + */ +#define DS2482_REG_CFG_1WS 0x08 +#define DS2482_REG_CFG_SPU 0x04 +#define DS2482_REG_CFG_PPM 0x02 +#define DS2482_REG_CFG_APU 0x01 + + +/** + * Write and verify codes for the CHANNEL_SELECT command (DS2482-800 only). + * To set the channel, write the value at the index of the channel. + * Read and compare against the corresponding value to verify the change. + */ +static const u8 ds2482_chan_wr[8] = + { 0xF0, 0xE1, 0xD2, 0xC3, 0xB4, 0xA5, 0x96, 0x87 }; +static const u8 ds2482_chan_rd[8] = + { 0xB8, 0xB1, 0xAA, 0xA3, 0x9C, 0x95, 0x8E, 0x87 }; + + +/** + * Status Register bit definitions (read only) + */ +#define DS2482_REG_STS_DIR 0x80 +#define DS2482_REG_STS_TSB 0x40 +#define DS2482_REG_STS_SBR 0x20 +#define DS2482_REG_STS_RST 0x10 +#define DS2482_REG_STS_LL 0x08 +#define DS2482_REG_STS_SD 0x04 +#define DS2482_REG_STS_PPD 0x02 +#define DS2482_REG_STS_1WB 0x01 + + +static int ds2482_attach_adapter(struct i2c_adapter *adapter); +static int ds2482_detect(struct i2c_adapter *adapter, int address, int kind); +static int ds2482_detach_client(struct i2c_client *client); + + +/** + * Driver data (common to all clients) + */ +static struct i2c_driver ds2482_driver = { + .driver = { + .owner = THIS_MODULE, + .name = "ds2482", + }, + .attach_adapter = ds2482_attach_adapter, + .detach_client = ds2482_detach_client, +}; + +/* + * Client data (each client gets its own) + */ + +struct ds2482_data; + +struct ds2482_w1_chan { + struct ds2482_data *pdev; + u8 channel; + struct w1_bus_master w1_bm; +}; + +struct ds2482_data { + struct i2c_client client; + struct semaphore access_lock; + + /* 1-wire interface(s) */ + int w1_count; /* 1 or 8 */ + struct ds2482_w1_chan w1_ch[8]; + + /* per-device values */ + u8 channel; + u8 read_prt; /* see DS2482_PTR_CODE_xxx */ + u8 reg_config; +}; + + +/** + * Sets the read pointer. + * @param pdev The ds2482 client pointer + * @param read_ptr see DS2482_PTR_CODE_xxx above + * @return -1 on failure, 0 on success + */ +static inline int ds2482_select_register(struct ds2482_data *pdev, u8 read_ptr) +{ + if (pdev->read_prt != read_ptr) { + if (i2c_smbus_write_byte_data(&pdev->client, + DS2482_CMD_SET_READ_PTR, + read_ptr) < 0) + return -1; + + pdev->read_prt = read_ptr; + } + return 0; +} + +/** + * Sends a command without a parameter + * @param pdev The ds2482 client pointer + * @param cmd DS2482_CMD_RESET, + * DS2482_CMD_1WIRE_RESET, + * DS2482_CMD_1WIRE_READ_BYTE + * @return -1 on failure, 0 on success + */ +static inline int ds2482_send_cmd(struct ds2482_data *pdev, u8 cmd) +{ + if (i2c_smbus_write_byte(&pdev->client, cmd) < 0) + return -1; + + pdev->read_prt = DS2482_PTR_CODE_STATUS; + return 0; +} + +/** + * Sends a command with a parameter + * @param pdev The ds2482 client pointer + * @param cmd DS2482_CMD_WRITE_CONFIG, + * DS2482_CMD_1WIRE_SINGLE_BIT, + * DS2482_CMD_1WIRE_WRITE_BYTE, + * DS2482_CMD_1WIRE_TRIPLET + * @param byte The data to send + * @return -1 on failure, 0 on success + */ +static inline int ds2482_send_cmd_data(struct ds2482_data *pdev, + u8 cmd, u8 byte) +{ + if (i2c_smbus_write_byte_data(&pdev->client, cmd, byte) < 0) + return -1; + + /* all cmds leave in STATUS, except CONFIG */ + pdev->read_prt = (cmd != DS2482_CMD_WRITE_CONFIG) ? + DS2482_PTR_CODE_STATUS : DS2482_PTR_CODE_CONFIG; + return 0; +} + + +/* + * 1-Wire interface code + */ + +#define DS2482_WAIT_IDLE_TIMEOUT 100 + +/** + * Waits until the 1-wire interface is idle (not busy) + * + * @param pdev Pointer to the device structure + * @return the last value read from status or -1 (failure) + */ +static int ds2482_wait_1wire_idle(struct ds2482_data *pdev) +{ + int temp = -1; + int retries = 0; + + if (!ds2482_select_register(pdev, DS2482_PTR_CODE_STATUS)) { + do { + temp = i2c_smbus_read_byte(&pdev->client); + } while ((temp >= 0) && (temp & DS2482_REG_STS_1WB) && + (++retries > DS2482_WAIT_IDLE_TIMEOUT)); + } + + if (retries > DS2482_WAIT_IDLE_TIMEOUT) + printk(KERN_ERR "%s: timeout on channel %d\n", + __func__, pdev->channel); + + return temp; +} + +/** + * Selects a w1 channel. + * The 1-wire interface must be idle before calling this function. + * + * @param pdev The ds2482 client pointer + * @param channel 0-7 + * @return -1 (failure) or 0 (success) + */ +static int ds2482_set_channel(struct ds2482_data *pdev, u8 channel) +{ + if (i2c_smbus_write_byte_data(&pdev->client, DS2482_CMD_CHANNEL_SELECT, + ds2482_chan_wr[channel]) < 0) + return -1; + + pdev->read_prt = DS2482_PTR_CODE_CHANNEL; + pdev->channel = -1; + if (i2c_smbus_read_byte(&pdev->client) == ds2482_chan_rd[channel]) { + pdev->channel = channel; + return 0; + } + return -1; +} + + +/** + * Performs the touch-bit function, which writes a 0 or 1 and reads the level. + * + * @param data The ds2482 channel pointer + * @param bit The level to write: 0 or non-zero + * @return The level read: 0 or 1 + */ +static u8 ds2482_w1_touch_bit(void *data, u8 bit) +{ + struct ds2482_w1_chan *pchan = data; + struct ds2482_data *pdev = pchan->pdev; + int status = -1; + + down(&pdev->access_lock); + + /* Select the channel */ + ds2482_wait_1wire_idle(pdev); + if (pdev->w1_count > 1) + ds2482_set_channel(pdev, pchan->channel); + + /* Send the touch command, wait until 1WB == 0, return the status */ + if (!ds2482_send_cmd_data(pdev, DS2482_CMD_1WIRE_SINGLE_BIT, + bit ? 0xFF : 0)) + status = ds2482_wait_1wire_idle(pdev); + + up(&pdev->access_lock); + + return (status & DS2482_REG_STS_SBR) ? 1 : 0; +} + +/** + * Performs the triplet function, which reads two bits and writes a bit. + * The bit written is determined by the two reads: + * 00 => dbit, 01 => 0, 10 => 1 + * + * @param data The ds2482 channel pointer + * @param dbit The direction to choose if both branches are valid + * @return b0=read1 b1=read2 b3=bit written + */ +static u8 ds2482_w1_triplet(void *data, u8 dbit) +{ + struct ds2482_w1_chan *pchan = data; + struct ds2482_data *pdev = pchan->pdev; + int status = (3 << 5); + + down(&pdev->access_lock); + + /* Select the channel */ + ds2482_wait_1wire_idle(pdev); + if (pdev->w1_count > 1) + ds2482_set_channel(pdev, pchan->channel); + + /* Send the triplet command, wait until 1WB == 0, return the status */ + if (!ds2482_send_cmd_data(pdev, DS2482_CMD_1WIRE_TRIPLET, + dbit ? 0xFF : 0)) + status = ds2482_wait_1wire_idle(pdev); + + up(&pdev->access_lock); + + /* Decode the status */ + return (status >> 5); +} + +/** + * Performs the write byte function. + * + * @param data The ds2482 channel pointer + * @param byte The value to write + */ +static void ds2482_w1_write_byte(void *data, u8 byte) +{ + struct ds2482_w1_chan *pchan = data; + struct ds2482_data *pdev = pchan->pdev; + + down(&pdev->access_lock); + + /* Select the channel */ + ds2482_wait_1wire_idle(pdev); + if (pdev->w1_count > 1) + ds2482_set_channel(pdev, pchan->channel); + + /* Send the write byte command */ + ds2482_send_cmd_data(pdev, DS2482_CMD_1WIRE_WRITE_BYTE, byte); + + up(&pdev->access_lock); +} + +/** + * Performs the read byte function. + * + * @param data The ds2482 channel pointer + * @return The value read + */ +static u8 ds2482_w1_read_byte(void *data) +{ + struct ds2482_w1_chan *pchan = data; + struct ds2482_data *pdev = pchan->pdev; + int result; + + down(&pdev->access_lock); + + /* Select the channel */ + ds2482_wait_1wire_idle(pdev); + if (pdev->w1_count > 1) + ds2482_set_channel(pdev, pchan->channel); + + /* Send the read byte command */ + ds2482_send_cmd(pdev, DS2482_CMD_1WIRE_READ_BYTE); + + /* Wait until 1WB == 0 */ + ds2482_wait_1wire_idle(pdev); + + /* Select the data register */ + ds2482_select_register(pdev, DS2482_PTR_CODE_DATA); + + /* Read the data byte */ + result = i2c_smbus_read_byte(&pdev->client); + + up(&pdev->access_lock); + + return result; +} + + +/** + * Sends a reset on the 1-wire interface + * + * @param data The ds2482 channel pointer + * @return 0=Device present, 1=No device present or error + */ +static u8 ds2482_w1_reset_bus(void *data) +{ + struct ds2482_w1_chan *pchan = data; + struct ds2482_data *pdev = pchan->pdev; + int err; + u8 retval = 1; + + down(&pdev->access_lock); + + /* Select the channel */ + ds2482_wait_1wire_idle(pdev); + if (pdev->w1_count > 1) + ds2482_set_channel(pdev, pchan->channel); + + /* Send the reset command */ + err = ds2482_send_cmd(pdev, DS2482_CMD_1WIRE_RESET); + if (err >= 0) { + /* Wait until the reset is complete */ + err = ds2482_wait_1wire_idle(pdev); + retval = !(err & DS2482_REG_STS_PPD); + + /* If the chip did reset since detect, re-config it */ + if (err & DS2482_REG_STS_RST) + ds2482_send_cmd_data(pdev, DS2482_CMD_WRITE_CONFIG, + 0xF0); + } + + up(&pdev->access_lock); + + return retval; +} + + +/** + * Called to see if the device exists on an i2c bus. + */ +static int ds2482_attach_adapter(struct i2c_adapter *adapter) +{ + return i2c_probe(adapter, &addr_data, ds2482_detect); +} + + +/* + * The following function does more than just detection. If detection + * succeeds, it also registers the new chip. + */ +static int ds2482_detect(struct i2c_adapter *adapter, int address, int kind) +{ + struct ds2482_data *data; + struct i2c_client *new_client; + int err = 0; + int temp1; + int idx; + + if (!i2c_check_functionality(adapter, + I2C_FUNC_SMBUS_WRITE_BYTE_DATA | + I2C_FUNC_SMBUS_BYTE)) + goto exit; + + if (!(data = kzalloc(sizeof(struct ds2482_data), GFP_KERNEL))) { + err = -ENOMEM; + goto exit; + } + + new_client = &data->client; + i2c_set_clientdata(new_client, data); + new_client->addr = address; + new_client->driver = &ds2482_driver; + new_client->adapter = adapter; + + /* Reset the device (sets the read_ptr to status) */ + if (ds2482_send_cmd(data, DS2482_CMD_RESET) < 0) { + dev_dbg(&adapter->dev, "DS2482 reset failed at 0x%02x.\n", + address); + goto exit_free; + } + + /* Sleep at least 525ns to allow the reset to complete */ + ndelay(525); + + /* Read the status byte - only reset bit and line should be set */ + temp1 = i2c_smbus_read_byte(new_client); + if (temp1 != (DS2482_REG_STS_LL | DS2482_REG_STS_RST)) { + dev_dbg(&adapter->dev, "DS2482 (0x%02x) reset status " + "0x%02X - not a DS2482\n", address, temp1); + goto exit_free; + } + + /* Detect the 8-port version */ + data->w1_count = 1; + if (ds2482_set_channel(data, 7) == 0) + data->w1_count = 8; + + /* Set all config items to 0 (off) */ + ds2482_send_cmd_data(data, DS2482_CMD_WRITE_CONFIG, 0xF0); + + /* We can fill in the remaining client fields */ + snprintf(new_client->name, sizeof(new_client->name), "ds2482-%d00", + data->w1_count); + + init_MUTEX(&data->access_lock); + + /* Tell the I2C layer a new client has arrived */ + if ((err = i2c_attach_client(new_client))) + goto exit_free; + + /* Register 1-wire interface(s) */ + for (idx = 0; idx < data->w1_count; idx++) { + data->w1_ch[idx].pdev = data; + data->w1_ch[idx].channel = idx; + + /* Populate all the w1 bus master stuff */ + data->w1_ch[idx].w1_bm.data = &data->w1_ch[idx]; + data->w1_ch[idx].w1_bm.read_byte = ds2482_w1_read_byte; + data->w1_ch[idx].w1_bm.write_byte = ds2482_w1_write_byte; + data->w1_ch[idx].w1_bm.touch_bit = ds2482_w1_touch_bit; + data->w1_ch[idx].w1_bm.triplet = ds2482_w1_triplet; + data->w1_ch[idx].w1_bm.reset_bus = ds2482_w1_reset_bus; + + err = w1_add_master_device(&data->w1_ch[idx].w1_bm); + if (err) { + data->w1_ch[idx].pdev = NULL; + goto exit_w1_remove; + } + } + + return 0; + +exit_w1_remove: + i2c_detach_client(new_client); + + for (idx = 0; idx < data->w1_count; idx++) { + if (data->w1_ch[idx].pdev != NULL) + w1_remove_master_device(&data->w1_ch[idx].w1_bm); + } +exit_free: + kfree(data); +exit: + return err; +} + +static int ds2482_detach_client(struct i2c_client *client) +{ + struct ds2482_data *data = i2c_get_clientdata(client); + int err, idx; + + /* Unregister the 1-wire bridge(s) */ + for (idx = 0; idx < data->w1_count; idx++) { + if (data->w1_ch[idx].pdev != NULL) + w1_remove_master_device(&data->w1_ch[idx].w1_bm); + } + + /* Detach the i2c device */ + if ((err = i2c_detach_client(client))) { + dev_err(&client->dev, + "Deregistration failed, client not detached.\n"); + return err; + } + + /* Free the memory */ + kfree(data); + return 0; +} + +static int __init sensors_ds2482_init(void) +{ + return i2c_add_driver(&ds2482_driver); +} + +static void __exit sensors_ds2482_exit(void) +{ + i2c_del_driver(&ds2482_driver); +} + +MODULE_AUTHOR("Ben Gardner "); +MODULE_DESCRIPTION("DS2482 driver"); +MODULE_LICENSE("GPL"); + +module_init(sensors_ds2482_init); +module_exit(sensors_ds2482_exit);