From: Stephen Hemminger Date: Wed, 22 Feb 2006 19:44:58 +0000 (-0800) Subject: [PATCH] sky2: yukon-ec-u chipset initialization X-Git-Tag: v2.6.16-rc5~53^2~1^2~10 X-Git-Url: https://err.no/cgi-bin/gitweb.cgi?a=commitdiff_plain;h=977bdf06ca8dd7ed081fab8d30249d9e6b1c24d3;p=linux-2.6 [PATCH] sky2: yukon-ec-u chipset initialization Add more complete setup code for Yukon EC_U chipset. Based on matching code in 8.31 code in SysKonnect vendor driver. Signed-off-by: Stephen Hemminger --- diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c index bfeba5b9cd..ce135b84a5 100644 --- a/drivers/net/sky2.c +++ b/drivers/net/sky2.c @@ -232,7 +232,17 @@ static int sky2_set_power_state(struct sky2_hw *hw, pci_power_t state) if (hw->ports > 1) reg1 |= PCI_Y2_PHY2_COMA; } + + if (hw->chip_id == CHIP_ID_YUKON_EC_U) { + pci_write_config_dword(hw->pdev, PCI_DEV_REG3, 0); + pci_read_config_dword(hw->pdev, PCI_DEV_REG4, ®1); + reg1 &= P_ASPM_CONTROL_MSK; + pci_write_config_dword(hw->pdev, PCI_DEV_REG4, reg1); + pci_write_config_dword(hw->pdev, PCI_DEV_REG5, 0); + } + pci_write_config_dword(hw->pdev, PCI_DEV_REG1, reg1); + break; case PCI_D3hot: @@ -463,16 +473,31 @@ static void sky2_phy_init(struct sky2_hw *hw, unsigned port) ledover |= PHY_M_LED_MO_RX(MO_LED_OFF); } - gm_phy_write(hw, port, PHY_MARV_LED_CTRL, ledctrl); + if (hw->chip_id == CHIP_ID_YUKON_EC_U && hw->chip_rev >= 2) { + /* apply fixes in PHY AFE */ + gm_phy_write(hw, port, 22, 255); + /* increase differential signal amplitude in 10BASE-T */ + gm_phy_write(hw, port, 24, 0xaa99); + gm_phy_write(hw, port, 23, 0x2011); - if (sky2->autoneg == AUTONEG_DISABLE || sky2->speed == SPEED_100) { - /* turn on 100 Mbps LED (LED_LINK100) */ - ledover |= PHY_M_LED_MO_100(MO_LED_ON); - } + /* fix for IEEE A/B Symmetry failure in 1000BASE-T */ + gm_phy_write(hw, port, 24, 0xa204); + gm_phy_write(hw, port, 23, 0x2002); - if (ledover) - gm_phy_write(hw, port, PHY_MARV_LED_OVER, ledover); + /* set page register to 0 */ + gm_phy_write(hw, port, 22, 0); + } else { + gm_phy_write(hw, port, PHY_MARV_LED_CTRL, ledctrl); + if (sky2->autoneg == AUTONEG_DISABLE || sky2->speed == SPEED_100) { + /* turn on 100 Mbps LED (LED_LINK100) */ + ledover |= PHY_M_LED_MO_100(MO_LED_ON); + } + + if (ledover) + gm_phy_write(hw, port, PHY_MARV_LED_OVER, ledover); + + } /* Enable phy interrupt on auto-negotiation complete (or link up) */ if (sky2->autoneg == AUTONEG_ENABLE) gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_IS_AN_COMPL); @@ -953,6 +978,12 @@ static int sky2_rx_start(struct sky2_port *sky2) sky2->rx_put = sky2->rx_next = 0; sky2_qset(hw, rxq); + + if (hw->chip_id == CHIP_ID_YUKON_EC_U && hw->chip_rev >= 2) { + /* MAC Rx RAM Read is controlled by hardware */ + sky2_write32(hw, Q_ADDR(rxq, Q_F), F_M_RX_RAM_DIS); + } + sky2_prefetch_init(hw, rxq, sky2->rx_le_map, RX_LE_SIZE - 1); rx_set_checksum(sky2); @@ -1035,9 +1066,10 @@ static int sky2_up(struct net_device *dev) RB_RST_SET); sky2_qset(hw, txqaddr[port]); - if (hw->chip_id == CHIP_ID_YUKON_EC_U) - sky2_write16(hw, Q_ADDR(txqaddr[port], Q_AL), 0x1a0); + /* Set almost empty threshold */ + if (hw->chip_id == CHIP_ID_YUKON_EC_U && hw->chip_rev == 1) + sky2_write16(hw, Q_ADDR(txqaddr[port], Q_AL), 0x1a0); sky2_prefetch_init(hw, txqaddr[port], sky2->tx_le_map, TX_RING_SIZE - 1); diff --git a/drivers/net/sky2.h b/drivers/net/sky2.h index fd12c289a2..d1c71f50d8 100644 --- a/drivers/net/sky2.h +++ b/drivers/net/sky2.h @@ -5,14 +5,22 @@ #define _SKY2_H /* PCI config registers */ -#define PCI_DEV_REG1 0x40 -#define PCI_DEV_REG2 0x44 -#define PCI_DEV_STATUS 0x7c -#define PCI_OS_PCI_X (1<<26) +enum { + PCI_DEV_REG1 = 0x40, + PCI_DEV_REG2 = 0x44, + PCI_DEV_STATUS = 0x7c, + PCI_DEV_REG3 = 0x80, + PCI_DEV_REG4 = 0x84, + PCI_DEV_REG5 = 0x88, +}; -#define PEX_LNK_STAT 0xf2 -#define PEX_UNC_ERR_STAT 0x104 -#define PEX_DEV_CTRL 0xe8 +enum { + PEX_DEV_CAP = 0xe4, + PEX_DEV_CTRL = 0xe8, + PEX_DEV_STA = 0xea, + PEX_LNK_STAT = 0xf2, + PEX_UNC_ERR_STAT= 0x104, +}; /* Yukon-2 */ enum pci_dev_reg_1 { @@ -37,6 +45,25 @@ enum pci_dev_reg_2 { PCI_USEDATA64 = 1<<0, /* Use 64Bit Data bus ext */ }; +/* PCI_OUR_REG_4 32 bit Our Register 4 (Yukon-ECU only) */ +enum pci_dev_reg_4 { + /* (Link Training & Status State Machine) */ + P_TIMER_VALUE_MSK = 0xffL<<16, /* Bit 23..16: Timer Value Mask */ + /* (Active State Power Management) */ + P_FORCE_ASPM_REQUEST = 1<<15, /* Force ASPM Request (A1 only) */ + P_ASPM_GPHY_LINK_DOWN = 1<<14, /* GPHY Link Down (A1 only) */ + P_ASPM_INT_FIFO_EMPTY = 1<<13, /* Internal FIFO Empty (A1 only) */ + P_ASPM_CLKRUN_REQUEST = 1<<12, /* CLKRUN Request (A1 only) */ + + P_ASPM_FORCE_CLKREQ_ENA = 1<<4, /* Force CLKREQ Enable (A1b only) */ + P_ASPM_CLKREQ_PAD_CTL = 1<<3, /* CLKREQ PAD Control (A1 only) */ + P_ASPM_A1_MODE_SELECT = 1<<2, /* A1 Mode Select (A1 only) */ + P_CLK_GATE_PEX_UNIT_ENA = 1<<1, /* Enable Gate PEX Unit Clock */ + P_CLK_GATE_ROOT_COR_ENA = 1<<0, /* Enable Gate Root Core Clock */ + P_ASPM_CONTROL_MSK = P_FORCE_ASPM_REQUEST | P_ASPM_GPHY_LINK_DOWN + | P_ASPM_CLKRUN_REQUEST | P_ASPM_INT_FIFO_EMPTY, +}; + #define PCI_STATUS_ERROR_BITS (PCI_STATUS_DETECTED_PARITY | \ PCI_STATUS_SIG_SYSTEM_ERROR | \ @@ -507,6 +534,16 @@ enum { }; #define Q_ADDR(reg, offs) (B8_Q_REGS + (reg) + (offs)) +/* Q_F 32 bit Flag Register */ +enum { + F_ALM_FULL = 1<<27, /* Rx FIFO: almost full */ + F_EMPTY = 1<<27, /* Tx FIFO: empty flag */ + F_FIFO_EOF = 1<<26, /* Tag (EOF Flag) bit in FIFO */ + F_WM_REACHED = 1<<25, /* Watermark reached */ + F_M_RX_RAM_DIS = 1<<24, /* MAC Rx RAM Read Port disable */ + F_FIFO_LEVEL = 0x1fL<<16, /* Bit 23..16: # of Qwords in FIFO */ + F_WATER_MARK = 0x0007ffL, /* Bit 10.. 0: Watermark */ +}; /* Queue Prefetch Unit Offsets, use Y2_QADDR() to address (Yukon-2 only)*/ enum { @@ -909,10 +946,12 @@ enum { PHY_BCOM_ID1_C0 = 0x6044, PHY_BCOM_ID1_C5 = 0x6047, - PHY_MARV_ID1_B0 = 0x0C23, /* Yukon (PHY 88E1011) */ + PHY_MARV_ID1_B0 = 0x0C23, /* Yukon (PHY 88E1011) */ PHY_MARV_ID1_B2 = 0x0C25, /* Yukon-Plus (PHY 88E1011) */ - PHY_MARV_ID1_C2 = 0x0CC2, /* Yukon-EC (PHY 88E1111) */ - PHY_MARV_ID1_Y2 = 0x0C91, /* Yukon-2 (PHY 88E1112) */ + PHY_MARV_ID1_C2 = 0x0CC2, /* Yukon-EC (PHY 88E1111) */ + PHY_MARV_ID1_Y2 = 0x0C91, /* Yukon-2 (PHY 88E1112) */ + PHY_MARV_ID1_FE = 0x0C83, /* Yukon-FE (PHY 88E3082 Rev.A1) */ + PHY_MARV_ID1_ECU= 0x0CB0, /* Yukon-ECU (PHY 88E1149 Rev.B2?) */ }; /* Advertisement register bits */