From: Mark Lord Date: Fri, 2 May 2008 06:07:51 +0000 (-0400) Subject: sata_mv more cosmetic changes X-Git-Tag: v2.6.26-rc2~59^2~23 X-Git-Url: https://err.no/cgi-bin/gitweb.cgi?a=commitdiff_plain;h=8e7decdb8b132ee970a2636931b7653dec6af472;p=linux-2.6 sata_mv more cosmetic changes More cosmetic changes; no code changes. -- try and improve consistency of naming. -- add missing _OFS to tails of register offset definitions. -- rename mv_setup_ifctl() to mv_setup_ifcfg(), since that's what it really does. -- remove/move some dead comments Signed-off-by: Mark Lord Signed-off-by: Jeff Garzik --- diff --git a/drivers/ata/sata_mv.c b/drivers/ata/sata_mv.c index 842b1a15b7..4eabb737a4 100644 --- a/drivers/ata/sata_mv.c +++ b/drivers/ata/sata_mv.c @@ -91,9 +91,9 @@ enum { MV_IRQ_COAL_TIME_THRESHOLD = (MV_IRQ_COAL_REG_BASE + 0xd0), MV_SATAHC0_REG_BASE = 0x20000, - MV_FLASH_CTL = 0x1046c, - MV_GPIO_PORT_CTL = 0x104f0, - MV_RESET_CFG = 0x180d8, + MV_FLASH_CTL_OFS = 0x1046c, + MV_GPIO_PORT_CTL_OFS = 0x104f0, + MV_RESET_CFG_OFS = 0x180d8, MV_PCI_REG_SZ = MV_MAJOR_REG_AREA_SZ, MV_SATAHC_REG_SZ = MV_MAJOR_REG_AREA_SZ, @@ -147,18 +147,21 @@ enum { /* PCI interface registers */ PCI_COMMAND_OFS = 0xc00, + PCI_COMMAND_MRDTRIG = (1 << 7), /* PCI Master Read Trigger */ PCI_MAIN_CMD_STS_OFS = 0xd30, STOP_PCI_MASTER = (1 << 2), PCI_MASTER_EMPTY = (1 << 3), GLOB_SFT_RST = (1 << 4), - MV_PCI_MODE = 0xd00, + MV_PCI_MODE_OFS = 0xd00, + MV_PCI_MODE_MASK = 0x30, + MV_PCI_EXP_ROM_BAR_CTL = 0xd2c, MV_PCI_DISC_TIMER = 0xd04, MV_PCI_MSI_TRIGGER = 0xc38, MV_PCI_SERR_MASK = 0xc28, - MV_PCI_XBAR_TMOUT = 0x1d04, + MV_PCI_XBAR_TMOUT_OFS = 0x1d04, MV_PCI_ERR_LOW_ADDRESS = 0x1d40, MV_PCI_ERR_HIGH_ADDRESS = 0x1d44, MV_PCI_ERR_ATTRIBUTE = 0x1d48, @@ -225,16 +228,18 @@ enum { PHY_MODE4 = 0x314, PHY_MODE2 = 0x330, SATA_IFCTL_OFS = 0x344, + SATA_TESTCTL_OFS = 0x348, SATA_IFSTAT_OFS = 0x34c, VENDOR_UNIQUE_FIS_OFS = 0x35c, - FIS_CFG_OFS = 0x360, - FIS_CFG_SINGLE_SYNC = (1 << 16), /* SYNC on DMA activation */ + FISCFG_OFS = 0x360, + FISCFG_WAIT_DEV_ERR = (1 << 8), /* wait for host on DevErr */ + FISCFG_SINGLE_SYNC = (1 << 16), /* SYNC on DMA activation */ MV5_PHY_MODE = 0x74, - MV5_LT_MODE = 0x30, - MV5_PHY_CTL = 0x0C, - SATA_INTERFACE_CFG = 0x050, + MV5_LTMODE_OFS = 0x30, + MV5_PHY_CTL_OFS = 0x0C, + SATA_INTERFACE_CFG_OFS = 0x050, MV_M2_PREAMP_MASK = 0x7e0, @@ -332,10 +337,16 @@ enum { EDMA_CMD_OFS = 0x28, /* EDMA command register */ EDMA_EN = (1 << 0), /* enable EDMA */ EDMA_DS = (1 << 1), /* disable EDMA; self-negated */ - ATA_RST = (1 << 2), /* reset trans/link/phy */ + EDMA_RESET = (1 << 2), /* reset eng/trans/link/phy */ + + EDMA_STATUS_OFS = 0x30, /* EDMA engine status */ + EDMA_STATUS_CACHE_EMPTY = (1 << 6), /* GenIIe command cache empty */ + EDMA_STATUS_IDLE = (1 << 7), /* GenIIe EDMA enabled/idle */ - EDMA_IORDY_TMOUT = 0x34, - EDMA_ARB_CFG = 0x38, + EDMA_IORDY_TMOUT_OFS = 0x34, + EDMA_ARB_CFG_OFS = 0x38, + + EDMA_HALTCOND_OFS = 0x60, /* GenIIe halt conditions */ GEN_II_NCQ_MAX_SECTORS = 256, /* max sects/io on Gen2 w/NCQ */ @@ -359,6 +370,7 @@ enum { #define IS_GEN_I(hpriv) ((hpriv)->hp_flags & MV_HP_GEN_I) #define IS_GEN_II(hpriv) ((hpriv)->hp_flags & MV_HP_GEN_II) #define IS_GEN_IIE(hpriv) ((hpriv)->hp_flags & MV_HP_GEN_IIE) +#define IS_PCIE(hpriv) ((hpriv)->hp_flags & MV_HP_PCIE) #define HAS_PCI(host) (!((host)->ports[0]->flags & MV_FLAG_SOC)) #define WINDOW_CTRL(i) (0x20030 + ((i) << 4)) @@ -1059,22 +1071,22 @@ static void mv6_dev_config(struct ata_device *adev) static void mv_config_fbs(void __iomem *port_mmio, int enable_fbs) { - u32 old_fcfg, new_fcfg, old_ltmode, new_ltmode; + u32 old_fiscfg, new_fiscfg, old_ltmode, new_ltmode; /* * Various bit settings required for operation * in FIS-based switching (fbs) mode on GenIIe: */ - old_fcfg = readl(port_mmio + FIS_CFG_OFS); + old_fiscfg = readl(port_mmio + FISCFG_OFS); old_ltmode = readl(port_mmio + LTMODE_OFS); if (enable_fbs) { - new_fcfg = old_fcfg | FIS_CFG_SINGLE_SYNC; + new_fiscfg = old_fiscfg | FISCFG_SINGLE_SYNC; new_ltmode = old_ltmode | LTMODE_BIT8; } else { /* disable fbs */ - new_fcfg = old_fcfg & ~FIS_CFG_SINGLE_SYNC; + new_fiscfg = old_fiscfg & ~FISCFG_SINGLE_SYNC; new_ltmode = old_ltmode & ~LTMODE_BIT8; } - if (new_fcfg != old_fcfg) - writelfl(new_fcfg, port_mmio + FIS_CFG_OFS); + if (new_fiscfg != old_fiscfg) + writelfl(new_fiscfg, port_mmio + FISCFG_OFS); if (new_ltmode != old_ltmode) writelfl(new_ltmode, port_mmio + LTMODE_OFS); } @@ -1894,7 +1906,7 @@ static void mv5_reset_bus(struct ata_host *host, void __iomem *mmio) static void mv5_reset_flash(struct mv_host_priv *hpriv, void __iomem *mmio) { - writel(0x0fcfffff, mmio + MV_FLASH_CTL); + writel(0x0fcfffff, mmio + MV_FLASH_CTL_OFS); } static void mv5_read_preamp(struct mv_host_priv *hpriv, int idx, @@ -1913,7 +1925,7 @@ static void mv5_enable_leds(struct mv_host_priv *hpriv, void __iomem *mmio) { u32 tmp; - writel(0, mmio + MV_GPIO_PORT_CTL); + writel(0, mmio + MV_GPIO_PORT_CTL_OFS); /* FIXME: handle MV_HP_ERRATA_50XXB2 errata */ @@ -1931,14 +1943,14 @@ static void mv5_phy_errata(struct mv_host_priv *hpriv, void __iomem *mmio, int fix_apm_sq = (hpriv->hp_flags & MV_HP_ERRATA_50XXB0); if (fix_apm_sq) { - tmp = readl(phy_mmio + MV5_LT_MODE); + tmp = readl(phy_mmio + MV5_LTMODE_OFS); tmp |= (1 << 19); - writel(tmp, phy_mmio + MV5_LT_MODE); + writel(tmp, phy_mmio + MV5_LTMODE_OFS); - tmp = readl(phy_mmio + MV5_PHY_CTL); + tmp = readl(phy_mmio + MV5_PHY_CTL_OFS); tmp &= ~0x3; tmp |= 0x1; - writel(tmp, phy_mmio + MV5_PHY_CTL); + writel(tmp, phy_mmio + MV5_PHY_CTL_OFS); } tmp = readl(phy_mmio + MV5_PHY_MODE); @@ -1956,11 +1968,6 @@ static void mv5_reset_hc_port(struct mv_host_priv *hpriv, void __iomem *mmio, { void __iomem *port_mmio = mv_port_base(mmio, port); - /* - * The datasheet warns against setting ATA_RST when EDMA is active - * (but doesn't say what the problem might be). So we first try - * to disable the EDMA engine before doing the ATA_RST operation. - */ mv_reset_channel(hpriv, mmio, port); ZERO(0x028); /* command */ @@ -1975,7 +1982,7 @@ static void mv5_reset_hc_port(struct mv_host_priv *hpriv, void __iomem *mmio, ZERO(0x024); /* respq outp */ ZERO(0x020); /* respq inp */ ZERO(0x02c); /* test control */ - writel(0xbc, port_mmio + EDMA_IORDY_TMOUT); + writel(0xbc, port_mmio + EDMA_IORDY_TMOUT_OFS); } #undef ZERO @@ -2021,13 +2028,13 @@ static void mv_reset_pci_bus(struct ata_host *host, void __iomem *mmio) struct mv_host_priv *hpriv = host->private_data; u32 tmp; - tmp = readl(mmio + MV_PCI_MODE); + tmp = readl(mmio + MV_PCI_MODE_OFS); tmp &= 0xff00ffff; - writel(tmp, mmio + MV_PCI_MODE); + writel(tmp, mmio + MV_PCI_MODE_OFS); ZERO(MV_PCI_DISC_TIMER); ZERO(MV_PCI_MSI_TRIGGER); - writel(0x000100ff, mmio + MV_PCI_XBAR_TMOUT); + writel(0x000100ff, mmio + MV_PCI_XBAR_TMOUT_OFS); ZERO(PCI_HC_MAIN_IRQ_MASK_OFS); ZERO(MV_PCI_SERR_MASK); ZERO(hpriv->irq_cause_ofs); @@ -2045,10 +2052,10 @@ static void mv6_reset_flash(struct mv_host_priv *hpriv, void __iomem *mmio) mv5_reset_flash(hpriv, mmio); - tmp = readl(mmio + MV_GPIO_PORT_CTL); + tmp = readl(mmio + MV_GPIO_PORT_CTL_OFS); tmp &= 0x3; tmp |= (1 << 5) | (1 << 6); - writel(tmp, mmio + MV_GPIO_PORT_CTL); + writel(tmp, mmio + MV_GPIO_PORT_CTL_OFS); } /** @@ -2121,7 +2128,7 @@ static void mv6_read_preamp(struct mv_host_priv *hpriv, int idx, void __iomem *port_mmio; u32 tmp; - tmp = readl(mmio + MV_RESET_CFG); + tmp = readl(mmio + MV_RESET_CFG_OFS); if ((tmp & (1 << 0)) == 0) { hpriv->signal[idx].amps = 0x7 << 8; hpriv->signal[idx].pre = 0x1 << 5; @@ -2137,7 +2144,7 @@ static void mv6_read_preamp(struct mv_host_priv *hpriv, int idx, static void mv6_enable_leds(struct mv_host_priv *hpriv, void __iomem *mmio) { - writel(0x00000060, mmio + MV_GPIO_PORT_CTL); + writel(0x00000060, mmio + MV_GPIO_PORT_CTL_OFS); } static void mv6_phy_errata(struct mv_host_priv *hpriv, void __iomem *mmio, @@ -2235,11 +2242,6 @@ static void mv_soc_reset_hc_port(struct mv_host_priv *hpriv, { void __iomem *port_mmio = mv_port_base(mmio, port); - /* - * The datasheet warns against setting ATA_RST when EDMA is active - * (but doesn't say what the problem might be). So we first try - * to disable the EDMA engine before doing the ATA_RST operation. - */ mv_reset_channel(hpriv, mmio, port); ZERO(0x028); /* command */ @@ -2254,7 +2256,7 @@ static void mv_soc_reset_hc_port(struct mv_host_priv *hpriv, ZERO(0x024); /* respq outp */ ZERO(0x020); /* respq inp */ ZERO(0x02c); /* test control */ - writel(0xbc, port_mmio + EDMA_IORDY_TMOUT); + writel(0xbc, port_mmio + EDMA_IORDY_TMOUT_OFS); } #undef ZERO @@ -2297,38 +2299,39 @@ static void mv_soc_reset_bus(struct ata_host *host, void __iomem *mmio) return; } -static void mv_setup_ifctl(void __iomem *port_mmio, int want_gen2i) +static void mv_setup_ifcfg(void __iomem *port_mmio, int want_gen2i) { - u32 ifctl = readl(port_mmio + SATA_INTERFACE_CFG); + u32 ifcfg = readl(port_mmio + SATA_INTERFACE_CFG_OFS); - ifctl = (ifctl & 0xf7f) | 0x9b1000; /* from chip spec */ + ifcfg = (ifcfg & 0xf7f) | 0x9b1000; /* from chip spec */ if (want_gen2i) - ifctl |= (1 << 7); /* enable gen2i speed */ - writelfl(ifctl, port_mmio + SATA_INTERFACE_CFG); + ifcfg |= (1 << 7); /* enable gen2i speed */ + writelfl(ifcfg, port_mmio + SATA_INTERFACE_CFG_OFS); } -/* - * Caller must ensure that EDMA is not active, - * by first doing mv_stop_edma() where needed. - */ static void mv_reset_channel(struct mv_host_priv *hpriv, void __iomem *mmio, unsigned int port_no) { void __iomem *port_mmio = mv_port_base(mmio, port_no); + /* + * The datasheet warns against setting EDMA_RESET when EDMA is active + * (but doesn't say what the problem might be). So we first try + * to disable the EDMA engine before doing the EDMA_RESET operation. + */ mv_stop_edma_engine(port_mmio); - writelfl(ATA_RST, port_mmio + EDMA_CMD_OFS); + writelfl(EDMA_RESET, port_mmio + EDMA_CMD_OFS); if (!IS_GEN_I(hpriv)) { - /* Enable 3.0gb/s link speed */ - mv_setup_ifctl(port_mmio, 1); + /* Enable 3.0gb/s link speed: this survives EDMA_RESET */ + mv_setup_ifcfg(port_mmio, 1); } /* - * Strobing ATA_RST here causes a hard reset of the SATA transport, + * Strobing EDMA_RESET here causes a hard reset of the SATA transport, * link, and physical layers. It resets all SATA interface registers * (except for SATA_INTERFACE_CFG), and issues a COMRESET to the dev. */ - writelfl(ATA_RST, port_mmio + EDMA_CMD_OFS); + writelfl(EDMA_RESET, port_mmio + EDMA_CMD_OFS); udelay(25); /* allow reset propagation */ writelfl(0, port_mmio + EDMA_CMD_OFS); @@ -2392,7 +2395,7 @@ static int mv_hardreset(struct ata_link *link, unsigned int *class, sata_scr_read(link, SCR_STATUS, &sstatus); if (!IS_GEN_I(hpriv) && ++attempts >= 5 && sstatus == 0x121) { /* Force 1.5gb/s link speed and try again */ - mv_setup_ifctl(mv_ap_base(ap), 0); + mv_setup_ifcfg(mv_ap_base(ap), 0); if (time_after(jiffies + HZ, deadline)) extra = HZ; /* only extend it once, max */ } @@ -2590,6 +2593,7 @@ static int mv_chip_id(struct ata_host *host, unsigned int board_idx) " and avoid the final two gigabytes on" " all RocketRAID BIOS initialized drives.\n"); } + /* drop through */ case chip_6042: hpriv->ops = &mv6xxx_ops; hp_flags |= MV_HP_GEN_IIE;