From: eric miao Date: Thu, 3 Jan 2008 03:25:56 +0000 (+0800) Subject: [ARM] pxa: make MFP configuration processor independent X-Git-Tag: v2.6.25-rc1~1175^2^2~18 X-Git-Url: https://err.no/cgi-bin/gitweb.cgi?a=commitdiff_plain;h=7f7c8a619253c83cf3b1071df3b001811d0c1a6c;p=linux-2.6 [ARM] pxa: make MFP configuration processor independent There are two reasons for making the MFP configuration to be processor independent, i.e. removing the relationship of configuration bits with actual MFPR register settings: 1. power management sometimes requires the MFP to be configured differently when in run mode or in low power mode 2. for future integration of pxa{25x,27x} GPIO configurations The modifications include: 1. introducing of processor independent MFP configuration bits, as defined in [include/asm-arm/arch-pxa/mfp.h]: bit 0.. 9 - MFP Pin Number (1024 Pins Maximum) bit 10..12 - Alternate Function Selection bit 13..15 - Drive Strength bit 16..18 - Low Power Mode State bit 19..20 - Low Power Mode Edge Detection bit 21..22 - Run Mode Pull State and so on, 2. moving the processor dependent code from mfp.h into mfp-pxa3xx.h 3. cleaning up of the MFPR bit definitions 4. mapping of processor independent MFP configuration into processor specific MFPR register settings is now totally encapsulated within pxa3xx_mfp_config() 5. using of "unsigned long" instead of invented type of "mfp_cfg_t" according to Documentation/CodingStyle Chapter 5, usage of this in platform code will be slowly removed in later patches Signed-off-by: eric miao Signed-off-by: Russell King --- diff --git a/arch/arm/mach-pxa/mfp.c b/arch/arm/mach-pxa/mfp.c index 785ae0ddb8..c66b1cd7df 100644 --- a/arch/arm/mach-pxa/mfp.c +++ b/arch/arm/mach-pxa/mfp.c @@ -20,6 +20,7 @@ #include #include +#include /* mfp_spin_lock is used to ensure that MFP register configuration * (most likely a read-modify-write operation) is atomic, and that @@ -28,43 +29,105 @@ static DEFINE_SPINLOCK(mfp_spin_lock); static void __iomem *mfpr_mmio_base = (void __iomem *)&__REG(MFPR_BASE); + +struct pxa3xx_mfp_pin { + unsigned long config; /* -1 for not configured */ + unsigned long mfpr_off; /* MFPRxx Register offset */ + unsigned long mfpr_run; /* Run-Mode Register Value */ + unsigned long mfpr_lpm; /* Low Power Mode Register Value */ +}; + static struct pxa3xx_mfp_pin mfp_table[MFP_PIN_MAX]; +/* mapping of MFP_LPM_* definitions to MFPR_LPM_* register bits */ +const static unsigned long mfpr_lpm[] = { + MFPR_LPM_INPUT, + MFPR_LPM_DRIVE_LOW, + MFPR_LPM_DRIVE_HIGH, + MFPR_LPM_PULL_LOW, + MFPR_LPM_PULL_HIGH, + MFPR_LPM_FLOAT, +}; + +/* mapping of MFP_PULL_* definitions to MFPR_PULL_* register bits */ +const static unsigned long mfpr_pull[] = { + MFPR_PULL_NONE, + MFPR_PULL_LOW, + MFPR_PULL_HIGH, + MFPR_PULL_BOTH, +}; + +/* mapping of MFP_LPM_EDGE_* definitions to MFPR_EDGE_* register bits */ +const static unsigned long mfpr_edge[] = { + MFPR_EDGE_NONE, + MFPR_EDGE_RISE, + MFPR_EDGE_FALL, + MFPR_EDGE_BOTH, +}; + #define mfpr_readl(off) \ __raw_readl(mfpr_mmio_base + (off)) #define mfpr_writel(off, val) \ __raw_writel(val, mfpr_mmio_base + (off)) +#define mfp_configured(p) ((p)->config != -1) + /* * perform a read-back of any MFPR register to make sure the * previous writings are finished */ #define mfpr_sync() (void)__raw_readl(mfpr_mmio_base + 0) -static inline void __mfp_config(int pin, unsigned long val) +static inline void __mfp_config_run(struct pxa3xx_mfp_pin *p) { - unsigned long off = mfp_table[pin].mfpr_off; + if (mfp_configured(p)) + mfpr_writel(p->mfpr_off, p->mfpr_run); +} - mfp_table[pin].mfpr_val = val; - mfpr_writel(off, val); +static inline void __mfp_config_lpm(struct pxa3xx_mfp_pin *p) +{ + if (mfp_configured(p) && p->mfpr_lpm != p->mfpr_run) + mfpr_writel(p->mfpr_off, p->mfpr_lpm); } -void pxa3xx_mfp_config(mfp_cfg_t *mfp_cfgs, int num) +void pxa3xx_mfp_config(unsigned long *mfp_cfgs, int num) { - int i, pin; - unsigned long val, flags; - mfp_cfg_t *mfp_cfg = mfp_cfgs; + unsigned long flags; + int i; spin_lock_irqsave(&mfp_spin_lock, flags); - for (i = 0; i < num; i++, mfp_cfg++) { - pin = MFP_CFG_PIN(*mfp_cfg); - val = MFP_CFG_VAL(*mfp_cfg); + for (i = 0; i < num; i++, mfp_cfgs++) { + unsigned long tmp, c = *mfp_cfgs; + struct pxa3xx_mfp_pin *p; + int pin, af, drv, lpm, edge, pull; + pin = MFP_PIN(c); BUG_ON(pin >= MFP_PIN_MAX); - - __mfp_config(pin, val); + p = &mfp_table[pin]; + + af = MFP_AF(c); + drv = MFP_DS(c); + lpm = MFP_LPM_STATE(c); + edge = MFP_LPM_EDGE(c); + pull = MFP_PULL(c); + + /* run-mode pull settings will conflict with MFPR bits of + * low power mode state, calculate mfpr_run and mfpr_lpm + * individually if pull != MFP_PULL_NONE + */ + tmp = MFPR_AF_SEL(af) | MFPR_DRIVE(drv); + + if (likely(pull == MFP_PULL_NONE)) { + p->mfpr_run = tmp | mfpr_lpm[lpm] | mfpr_edge[edge]; + p->mfpr_lpm = p->mfpr_run; + } else { + p->mfpr_lpm = tmp | mfpr_lpm[lpm] | mfpr_edge[edge]; + p->mfpr_run = tmp | mfpr_pull[pull]; + } + + p->config = c; __mfp_config_run(p); } mfpr_sync(); @@ -110,7 +173,8 @@ void __init pxa3xx_mfp_init_addr(struct pxa3xx_mfp_addr_map *map) do { mfp_table[i].mfpr_off = offset; - mfp_table[i].mfpr_val = 0; + mfp_table[i].mfpr_run = 0; + mfp_table[i].mfpr_lpm = 0; offset += 4; i++; } while ((i <= p->end) && (p->end != -1)); } @@ -120,5 +184,8 @@ void __init pxa3xx_mfp_init_addr(struct pxa3xx_mfp_addr_map *map) void __init pxa3xx_init_mfp(void) { - memset(mfp_table, 0, sizeof(mfp_table)); + int i; + + for (i = 0; i < ARRAY_SIZE(mfp_table); i++) + mfp_table[i].config = -1; } diff --git a/include/asm-arm/arch-pxa/mfp-pxa3xx.h b/include/asm-arm/arch-pxa/mfp-pxa3xx.h index 5da1857d54..1f6b35c015 100644 --- a/include/asm-arm/arch-pxa/mfp-pxa3xx.h +++ b/include/asm-arm/arch-pxa/mfp-pxa3xx.h @@ -1,6 +1,69 @@ #ifndef __ASM_ARCH_MFP_PXA3XX_H #define __ASM_ARCH_MFP_PXA3XX_H +#define MFPR_BASE (0x40e10000) +#define MFPR_SIZE (PAGE_SIZE) + +/* MFPR register bit definitions */ +#define MFPR_PULL_SEL (0x1 << 15) +#define MFPR_PULLUP_EN (0x1 << 14) +#define MFPR_PULLDOWN_EN (0x1 << 13) +#define MFPR_SLEEP_SEL (0x1 << 9) +#define MFPR_SLEEP_OE_N (0x1 << 7) +#define MFPR_EDGE_CLEAR (0x1 << 6) +#define MFPR_EDGE_FALL_EN (0x1 << 5) +#define MFPR_EDGE_RISE_EN (0x1 << 4) + +#define MFPR_SLEEP_DATA(x) ((x) << 8) +#define MFPR_DRIVE(x) (((x) & 0x7) << 10) +#define MFPR_AF_SEL(x) (((x) & 0x7) << 0) + +#define MFPR_EDGE_NONE (0) +#define MFPR_EDGE_RISE (MFPR_EDGE_RISE_EN) +#define MFPR_EDGE_FALL (MFPR_EDGE_FALL_EN) +#define MFPR_EDGE_BOTH (MFPR_EDGE_RISE | MFPR_EDGE_FALL) + +/* + * Table that determines the low power modes outputs, with actual settings + * used in parentheses for don't-care values. Except for the float output, + * the configured driven and pulled levels match, so if there is a need for + * non-LPM pulled output, the same configuration could probably be used. + * + * Output value sleep_oe_n sleep_data pullup_en pulldown_en pull_sel + * (bit 7) (bit 8) (bit 14) (bit 13) (bit 15) + * + * Input 0 X(0) X(0) X(0) 0 + * Drive 0 0 0 0 X(1) 0 + * Drive 1 0 1 X(1) 0 0 + * Pull hi (1) 1 X(1) 1 0 0 + * Pull lo (0) 1 X(0) 0 1 0 + * Z (float) 1 X(0) 0 0 0 + */ +#define MFPR_LPM_INPUT (0) +#define MFPR_LPM_DRIVE_LOW (MFPR_SLEEP_DATA(0) | MFPR_PULLDOWN_EN) +#define MFPR_LPM_DRIVE_HIGH (MFPR_SLEEP_DATA(1) | MFPR_PULLUP_EN) +#define MFPR_LPM_PULL_LOW (MFPR_LPM_DRIVE_LOW | MFPR_SLEEP_OE_N) +#define MFPR_LPM_PULL_HIGH (MFPR_LPM_DRIVE_HIGH | MFPR_SLEEP_OE_N) +#define MFPR_LPM_FLOAT (MFPR_SLEEP_OE_N) +#define MFPR_LPM_MASK (0xe080) + +/* + * The pullup and pulldown state of the MFP pin at run mode is by default + * determined by the selected alternate function. In case that some buggy + * devices need to override this default behavior, the definitions below + * indicates the setting of corresponding MFPR bits + * + * Definition pull_sel pullup_en pulldown_en + * MFPR_PULL_NONE 0 0 0 + * MFPR_PULL_LOW 1 0 1 + * MFPR_PULL_HIGH 1 1 0 + * MFPR_PULL_BOTH 1 1 1 + */ +#define MFPR_PULL_NONE (0) +#define MFPR_PULL_LOW (MFPR_PULL_SEL | MFPR_PULLDOWN_EN) +#define MFPR_PULL_BOTH (MFPR_PULL_LOW | MFPR_PULLUP_EN) +#define MFPR_PULL_HIGH (MFPR_PULL_SEL | MFPR_PULLUP_EN) + /* PXA3xx common MFP configurations - processor specific ones defined * in mfp-pxa300.h and mfp-pxa320.h */ @@ -134,4 +197,56 @@ #define GPIO5_2_GPIO MFP_CFG(GPIO5_2, AF0) #define GPIO6_2_GPIO MFP_CFG(GPIO6_2, AF0) +/* + * each MFP pin will have a MFPR register, since the offset of the + * register varies between processors, the processor specific code + * should initialize the pin offsets by pxa3xx_mfp_init_addr() + * + * pxa3xx_mfp_init_addr - accepts a table of "pxa3xx_mfp_addr_map" + * structure, which represents a range of MFP pins from "start" to + * "end", with the offset begining at "offset", to define a single + * pin, let "end" = -1 + * + * use + * + * MFP_ADDR_X() to define a range of pins + * MFP_ADDR() to define a single pin + * MFP_ADDR_END to signal the end of pin offset definitions + */ +struct pxa3xx_mfp_addr_map { + unsigned int start; + unsigned int end; + unsigned long offset; +}; + +#define MFP_ADDR_X(start, end, offset) \ + { MFP_PIN_##start, MFP_PIN_##end, offset } + +#define MFP_ADDR(pin, offset) \ + { MFP_PIN_##pin, -1, offset } + +#define MFP_ADDR_END { MFP_PIN_INVALID, 0 } + +/* + * pxa3xx_mfp_read()/pxa3xx_mfp_write() - for direct read/write access + * to the MFPR register + */ +unsigned long pxa3xx_mfp_read(int mfp); +void pxa3xx_mfp_write(int mfp, unsigned long mfpr_val); + +/* + * pxa3xx_mfp_config - configure the MFPR registers + * + * used by board specific initialization code + */ +void pxa3xx_mfp_config(unsigned long *mfp_cfgs, int num); + +/* + * pxa3xx_mfp_init_addr() - initialize the mapping between mfp pin + * index and MFPR register offset + * + * used by processor specific code + */ +void __init pxa3xx_mfp_init_addr(struct pxa3xx_mfp_addr_map *); +void __init pxa3xx_init_mfp(void); #endif /* __ASM_ARCH_MFP_PXA3XX_H */ diff --git a/include/asm-arm/arch-pxa/mfp.h b/include/asm-arm/arch-pxa/mfp.h index 60fbed1b2e..02f6157396 100644 --- a/include/asm-arm/arch-pxa/mfp.h +++ b/include/asm-arm/arch-pxa/mfp.h @@ -16,9 +16,6 @@ #ifndef __ASM_ARCH_MFP_H #define __ASM_ARCH_MFP_H -#define MFPR_BASE (0x40e10000) -#define MFPR_SIZE (PAGE_SIZE) - #define mfp_to_gpio(m) ((m) % 128) /* list of all the configurable MFP pins */ @@ -216,115 +213,22 @@ enum { MFP_PIN_MAX, }; -/* - * Table that determines the low power modes outputs, with actual settings - * used in parentheses for don't-care values. Except for the float output, - * the configured driven and pulled levels match, so if there is a need for - * non-LPM pulled output, the same configuration could probably be used. - * - * Output value sleep_oe_n sleep_data pullup_en pulldown_en pull_sel - * (bit 7) (bit 8) (bit 14d) (bit 13d) - * - * Drive 0 0 0 0 X (1) 0 - * Drive 1 0 1 X (1) 0 0 - * Pull hi (1) 1 X(1) 1 0 0 - * Pull lo (0) 1 X(0) 0 1 0 - * Z (float) 1 X(0) 0 0 0 - */ -#define MFP_LPM_DRIVE_LOW 0x8 -#define MFP_LPM_DRIVE_HIGH 0x6 -#define MFP_LPM_PULL_HIGH 0x7 -#define MFP_LPM_PULL_LOW 0x9 -#define MFP_LPM_FLOAT 0x1 -#define MFP_LPM_PULL_NEITHER 0x0 - -/* - * The pullup and pulldown state of the MFP pin is by default determined by - * selected alternate function. In case some buggy devices need to override - * this default behavior, pxa3xx_mfp_set_pull() can be invoked with one of - * the following definition as the parameter. - * - * Definition pull_sel pullup_en pulldown_en - * MFP_PULL_HIGH 1 1 0 - * MFP_PULL_LOW 1 0 1 - * MFP_PULL_BOTH 1 1 1 - * MFP_PULL_NONE 1 0 0 - * MFP_PULL_DEFAULT 0 X X - * - * NOTE: pxa3xx_mfp_set_pull() will modify the PULLUP_EN and PULLDOWN_EN - * bits, which will cause potential conflicts with the low power mode - * setting, device drivers should take care of this - */ -#define MFP_PULL_BOTH (0x7u) -#define MFP_PULL_HIGH (0x6u) -#define MFP_PULL_LOW (0x5u) -#define MFP_PULL_NONE (0x4u) -#define MFP_PULL_DEFAULT (0x0u) - -#define MFP_AF0 (0) -#define MFP_AF1 (1) -#define MFP_AF2 (2) -#define MFP_AF3 (3) -#define MFP_AF4 (4) -#define MFP_AF5 (5) -#define MFP_AF6 (6) -#define MFP_AF7 (7) - -#define MFP_DS01X (0) -#define MFP_DS02X (1) -#define MFP_DS03X (2) -#define MFP_DS04X (3) -#define MFP_DS06X (4) -#define MFP_DS08X (5) -#define MFP_DS10X (6) -#define MFP_DS12X (7) - -#define MFP_EDGE_BOTH 0x3 -#define MFP_EDGE_RISE 0x2 -#define MFP_EDGE_FALL 0x1 -#define MFP_EDGE_NONE 0x0 - -#define MFPR_AF_MASK 0x0007 -#define MFPR_DRV_MASK 0x1c00 -#define MFPR_RDH_MASK 0x0200 -#define MFPR_LPM_MASK 0xe180 -#define MFPR_PULL_MASK 0xe000 -#define MFPR_EDGE_MASK 0x0070 - -#define MFPR_ALT_OFFSET 0 -#define MFPR_ERE_OFFSET 4 -#define MFPR_EFE_OFFSET 5 -#define MFPR_EC_OFFSET 6 -#define MFPR_SON_OFFSET 7 -#define MFPR_SD_OFFSET 8 -#define MFPR_SS_OFFSET 9 -#define MFPR_DRV_OFFSET 10 -#define MFPR_PD_OFFSET 13 -#define MFPR_PU_OFFSET 14 -#define MFPR_PS_OFFSET 15 - -#define MFPR(af, drv, rdh, lpm, edge) \ - (((af) & 0x7) | (((drv) & 0x7) << 10) |\ - (((rdh) & 0x1) << 9) |\ - (((lpm) & 0x3) << 7) |\ - (((lpm) & 0x4) << 12)|\ - (((lpm) & 0x8) << 10)|\ - ((!(edge)) << 6) |\ - (((edge) & 0x1) << 5) |\ - (((edge) & 0x2) << 3)) - /* * a possible MFP configuration is represented by a 32-bit integer - * bit 0..15 - MFPR value (16-bit) - * bit 16..31 - mfp pin index (used to obtain the MFPR offset) + * + * bit 0.. 9 - MFP Pin Number (1024 Pins Maximum) + * bit 10..12 - Alternate Function Selection + * bit 13..15 - Drive Strength + * bit 16..18 - Low Power Mode State + * bit 19..20 - Low Power Mode Edge Detection + * bit 21..22 - Run Mode Pull State * * to facilitate the definition, the following macros are provided * - * MFPR_DEFAULT - default MFPR value, with + * MFP_CFG_DEFAULT - default MFP configuration value, with * alternate function = 0, - * drive strength = fast 1mA (MFP_DS01X) + * drive strength = fast 3mA (MFP_DS03X) * low power mode = default - * release dalay hold = false (RDH bit) * edge detection = none * * MFP_CFG - default MFPR value with alternate function @@ -334,104 +238,74 @@ enum { * low power mode * MFP_CFG_X - default MFPR value with alternate function, * pin drive strength and low power mode - * - * use - * - * MFP_CFG_PIN - to get the MFP pin index - * MFP_CFG_VAL - to get the corresponding MFPR value */ -typedef uint32_t mfp_cfg_t; - -#define MFP_CFG_PIN(mfp_cfg) (((mfp_cfg) >> 16) & 0xffff) -#define MFP_CFG_VAL(mfp_cfg) ((mfp_cfg) & 0xffff) - -/* - * MFP register defaults to - * drive strength fast 3mA (010'b) - * edge detection logic disabled - * alternate function 0 - */ -#define MFPR_DEFAULT (0x0840) +typedef unsigned long mfp_cfg_t; + +#define MFP_PIN(x) ((x) & 0x3ff) + +#define MFP_AF0 (0x0 << 10) +#define MFP_AF1 (0x1 << 10) +#define MFP_AF2 (0x2 << 10) +#define MFP_AF3 (0x3 << 10) +#define MFP_AF4 (0x4 << 10) +#define MFP_AF5 (0x5 << 10) +#define MFP_AF6 (0x6 << 10) +#define MFP_AF7 (0x7 << 10) +#define MFP_AF_MASK (0x7 << 10) +#define MFP_AF(x) (((x) >> 10) & 0x7) + +#define MFP_DS01X (0x0 << 13) +#define MFP_DS02X (0x1 << 13) +#define MFP_DS03X (0x2 << 13) +#define MFP_DS04X (0x3 << 13) +#define MFP_DS06X (0x4 << 13) +#define MFP_DS08X (0x5 << 13) +#define MFP_DS10X (0x6 << 13) +#define MFP_DS13X (0x7 << 13) +#define MFP_DS_MASK (0x7 << 13) +#define MFP_DS(x) (((x) >> 13) & 0x7) + +#define MFP_LPM_INPUT (0x0 << 16) +#define MFP_LPM_DRIVE_LOW (0x1 << 16) +#define MFP_LPM_DRIVE_HIGH (0x2 << 16) +#define MFP_LPM_PULL_LOW (0x3 << 16) +#define MFP_LPM_PULL_HIGH (0x4 << 16) +#define MFP_LPM_FLOAT (0x5 << 16) +#define MFP_LPM_STATE_MASK (0x7 << 16) +#define MFP_LPM_STATE(x) (((x) >> 16) & 0x7) + +#define MFP_LPM_EDGE_NONE (0x0 << 19) +#define MFP_LPM_EDGE_RISE (0x1 << 19) +#define MFP_LPM_EDGE_FALL (0x2 << 19) +#define MFP_LPM_EDGE_BOTH (0x3 << 19) +#define MFP_LPM_EDGE_MASK (0x3 << 19) +#define MFP_LPM_EDGE(x) (((x) >> 19) & 0x3) + +#define MFP_PULL_NONE (0x0 << 21) +#define MFP_PULL_LOW (0x1 << 21) +#define MFP_PULL_HIGH (0x2 << 21) +#define MFP_PULL_BOTH (0x3 << 21) +#define MFP_PULL_MASK (0x3 << 21) +#define MFP_PULL(x) (((x) >> 21) & 0x3) + +#define MFP_CFG_DEFAULT (MFP_AF0 | MFP_DS03X | MFP_LPM_INPUT |\ + MFP_LPM_EDGE_NONE | MFP_PULL_NONE) #define MFP_CFG(pin, af) \ - ((MFP_PIN_##pin << 16) | MFPR_DEFAULT | (MFP_##af)) + ((MFP_CFG_DEFAULT & ~MFP_AF_MASK) |\ + (MFP_PIN(MFP_PIN_##pin) | MFP_##af)) #define MFP_CFG_DRV(pin, af, drv) \ - ((MFP_PIN_##pin << 16) | (MFPR_DEFAULT & ~MFPR_DRV_MASK) |\ - ((MFP_##drv) << 10) | (MFP_##af)) + ((MFP_CFG_DEFAULT & ~(MFP_AF_MASK | MFP_DS_MASK)) |\ + (MFP_PIN(MFP_PIN_##pin) | MFP_##af | MFP_##drv)) #define MFP_CFG_LPM(pin, af, lpm) \ - ((MFP_PIN_##pin << 16) | (MFPR_DEFAULT & ~MFPR_LPM_MASK) |\ - (((MFP_LPM_##lpm) & 0x3) << 7) |\ - (((MFP_LPM_##lpm) & 0x4) << 12) |\ - (((MFP_LPM_##lpm) & 0x8) << 10) |\ - (MFP_##af)) + ((MFP_CFG_DEFAULT & ~(MFP_AF_MASK | MFP_LPM_STATE_MASK)) |\ + (MFP_PIN(MFP_PIN_##pin) | MFP_##af | MFP_LPM_##lpm)) #define MFP_CFG_X(pin, af, drv, lpm) \ - ((MFP_PIN_##pin << 16) |\ - (MFPR_DEFAULT & ~(MFPR_DRV_MASK | MFPR_LPM_MASK)) |\ - ((MFP_##drv) << 10) | (MFP_##af) |\ - (((MFP_LPM_##lpm) & 0x3) << 7) |\ - (((MFP_LPM_##lpm) & 0x4) << 12) |\ - (((MFP_LPM_##lpm) & 0x8) << 10)) - -/* - * each MFP pin will have a MFPR register, since the offset of the - * register varies between processors, the processor specific code - * should initialize the pin offsets by pxa3xx_mfp_init_addr() - * - * pxa3xx_mfp_init_addr - accepts a table of "pxa3xx_mfp_addr_map" - * structure, which represents a range of MFP pins from "start" to - * "end", with the offset begining at "offset", to define a single - * pin, let "end" = -1 - * - * use - * - * MFP_ADDR_X() to define a range of pins - * MFP_ADDR() to define a single pin - * MFP_ADDR_END to signal the end of pin offset definitions - */ -struct pxa3xx_mfp_addr_map { - unsigned int start; - unsigned int end; - unsigned long offset; -}; - -#define MFP_ADDR_X(start, end, offset) \ - { MFP_PIN_##start, MFP_PIN_##end, offset } - -#define MFP_ADDR(pin, offset) \ - { MFP_PIN_##pin, -1, offset } - -#define MFP_ADDR_END { MFP_PIN_INVALID, 0 } - -struct pxa3xx_mfp_pin { - unsigned long mfpr_off; /* MFPRxx register offset */ - unsigned long mfpr_val; /* MFPRxx register value */ -}; - -/* - * pxa3xx_mfp_read()/pxa3xx_mfp_write() - for direct read/write access - * to the MFPR register - */ -unsigned long pxa3xx_mfp_read(int mfp); -void pxa3xx_mfp_write(int mfp, unsigned long mfpr_val); - -/* - * pxa3xx_mfp_config - configure the MFPR registers - * - * used by board specific initialization code - */ -void pxa3xx_mfp_config(mfp_cfg_t *mfp_cfgs, int num); - -/* - * pxa3xx_mfp_init_addr() - initialize the mapping between mfp pin - * index and MFPR register offset - * - * used by processor specific code - */ -void __init pxa3xx_mfp_init_addr(struct pxa3xx_mfp_addr_map *); -void __init pxa3xx_init_mfp(void); + ((MFP_CFG_DEFAULT & ~(MFP_AF_MASK | MFP_DS_MASK | MFP_LPM_STATE_MASK)) |\ + (MFP_PIN(MFP_PIN_##pin) | MFP_##af | MFP_##drv | MFP_LPM_##lpm)) #endif /* __ASM_ARCH_MFP_H */