From: Ben Dooks Date: Sat, 24 Jun 2006 20:21:32 +0000 (+0100) Subject: [ARM] 3639/1: S3C2412: serial port support X-Git-Tag: v2.6.18-rc1~1071^2~1^2~6 X-Git-Url: https://err.no/cgi-bin/gitweb.cgi?a=commitdiff_plain;h=73e55cb3b3549d0174d1dadb755200938232e8d0;p=linux-2.6 [ARM] 3639/1: S3C2412: serial port support Patch from Ben Dooks Serial port support for the on-board UART blocks on the Samsung S3C2412 and S3C2413 UARTs. Signed-off-by: Ben Dooks Signed-off-by: Russell King --- diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig index bef4a9622e..5b48ac22c9 100644 --- a/drivers/serial/Kconfig +++ b/drivers/serial/Kconfig @@ -354,21 +354,24 @@ config SERIAL_CLPS711X_CONSOLE kernel at boot time.) config SERIAL_S3C2410 - tristate "Samsung S3C2410 Serial port support" + tristate "Samsung S3C2410/S3C2440/S3C2442/S3C2412 Serial port support" depends on ARM && ARCH_S3C2410 select SERIAL_CORE help - Support for the on-chip UARTs on the Samsung S3C2410X CPU, + Support for the on-chip UARTs on the Samsung S3C24XX series CPUs, providing /dev/ttySAC0, 1 and 2 (note, some machines may not provide all of these ports, depending on how the serial port pins are configured. + Currently this driver supports the UARTS on the S3C2410, S3C2440, + S3C2442, S3C2412 and S3C2413 CPUs. + config SERIAL_S3C2410_CONSOLE bool "Support for console on S3C2410 serial port" depends on SERIAL_S3C2410=y select SERIAL_CORE_CONSOLE help - Allow selection of the S3C2410 on-board serial ports for use as + Allow selection of the S3C24XX on-board serial ports for use as an virtual console. Even if you say Y here, the currently visible virtual console diff --git a/drivers/serial/s3c2410.c b/drivers/serial/s3c2410.c index 53c2465bad..837b6da520 100644 --- a/drivers/serial/s3c2410.c +++ b/drivers/serial/s3c2410.c @@ -872,6 +872,8 @@ static const char *s3c24xx_serial_type(struct uart_port *port) return "S3C2410"; case PORT_S3C2440: return "S3C2440"; + case PORT_S3C2412: + return "S3C2412"; default: return NULL; } @@ -1528,6 +1530,141 @@ static inline void s3c2440_serial_exit(void) #define s3c2440_uart_inf_at NULL #endif /* CONFIG_CPU_S3C2440 */ +#if defined(CONFIG_CPU_S3C2412) || defined(CONFIG_CPU_S3C2413) + +static int s3c2412_serial_setsource(struct uart_port *port, + struct s3c24xx_uart_clksrc *clk) +{ + unsigned long ucon = rd_regl(port, S3C2410_UCON); + + ucon &= ~S3C2412_UCON_CLKMASK; + + if (strcmp(clk->name, "uclk") == 0) + ucon |= S3C2440_UCON_UCLK; + else if (strcmp(clk->name, "pclk") == 0) + ucon |= S3C2440_UCON_PCLK; + else if (strcmp(clk->name, "usysclk") == 0) + ucon |= S3C2412_UCON_USYSCLK; + else { + printk(KERN_ERR "unknown clock source %s\n", clk->name); + return -EINVAL; + } + + wr_regl(port, S3C2410_UCON, ucon); + return 0; +} + + +static int s3c2412_serial_getsource(struct uart_port *port, + struct s3c24xx_uart_clksrc *clk) +{ + unsigned long ucon = rd_regl(port, S3C2410_UCON); + + switch (ucon & S3C2412_UCON_CLKMASK) { + case S3C2412_UCON_UCLK: + clk->divisor = 1; + clk->name = "uclk"; + break; + + case S3C2412_UCON_PCLK: + case S3C2412_UCON_PCLK2: + clk->divisor = 1; + clk->name = "pclk"; + break; + + case S3C2412_UCON_USYSCLK: + clk->divisor = 1; + clk->name = "usysclk"; + break; + } + + return 0; +} + +static int s3c2412_serial_resetport(struct uart_port *port, + struct s3c2410_uartcfg *cfg) +{ + unsigned long ucon = rd_regl(port, S3C2410_UCON); + + dbg("%s: port=%p (%08lx), cfg=%p\n", + __FUNCTION__, port, port->mapbase, cfg); + + /* ensure we don't change the clock settings... */ + + ucon &= S3C2412_UCON_CLKMASK; + + wr_regl(port, S3C2410_UCON, ucon | cfg->ucon); + wr_regl(port, S3C2410_ULCON, cfg->ulcon); + + /* reset both fifos */ + + wr_regl(port, S3C2410_UFCON, cfg->ufcon | S3C2410_UFCON_RESETBOTH); + wr_regl(port, S3C2410_UFCON, cfg->ufcon); + + return 0; +} + +static struct s3c24xx_uart_info s3c2412_uart_inf = { + .name = "Samsung S3C2412 UART", + .type = PORT_S3C2412, + .fifosize = 64, + .rx_fifomask = S3C2440_UFSTAT_RXMASK, + .rx_fifoshift = S3C2440_UFSTAT_RXSHIFT, + .rx_fifofull = S3C2440_UFSTAT_RXFULL, + .tx_fifofull = S3C2440_UFSTAT_TXFULL, + .tx_fifomask = S3C2440_UFSTAT_TXMASK, + .tx_fifoshift = S3C2440_UFSTAT_TXSHIFT, + .get_clksrc = s3c2412_serial_getsource, + .set_clksrc = s3c2412_serial_setsource, + .reset_port = s3c2412_serial_resetport, +}; + +/* device management */ + +static int s3c2412_serial_probe(struct platform_device *dev) +{ + dbg("s3c2440_serial_probe: dev=%p\n", dev); + return s3c24xx_serial_probe(dev, &s3c2440_uart_inf); +} + +static struct platform_driver s3c2412_serial_drv = { + .probe = s3c2412_serial_probe, + .remove = s3c24xx_serial_remove, + .suspend = s3c24xx_serial_suspend, + .resume = s3c24xx_serial_resume, + .driver = { + .name = "s3c2412-uart", + .owner = THIS_MODULE, + }, +}; + + +static inline int s3c2412_serial_init(void) +{ + return s3c24xx_serial_init(&s3c2412_serial_drv, &s3c2412_uart_inf); +} + +static inline void s3c2412_serial_exit(void) +{ + platform_driver_unregister(&s3c2412_serial_drv); +} + +#define s3c2412_uart_inf_at &s3c2412_uart_inf +#else + +static inline int s3c2412_serial_init(void) +{ + return 0; +} + +static inline void s3c2412_serial_exit(void) +{ +} + +#define s3c2412_uart_inf_at NULL +#endif /* CONFIG_CPU_S3C2440 */ + + /* module initialisation code */ static int __init s3c24xx_serial_modinit(void) @@ -1542,6 +1679,7 @@ static int __init s3c24xx_serial_modinit(void) s3c2400_serial_init(); s3c2410_serial_init(); + s3c2412_serial_init(); s3c2440_serial_init(); return 0; @@ -1551,6 +1689,7 @@ static void __exit s3c24xx_serial_modexit(void) { s3c2400_serial_exit(); s3c2410_serial_exit(); + s3c2412_serial_exit(); s3c2440_serial_exit(); uart_unregister_driver(&s3c24xx_uart_drv); @@ -1773,6 +1912,8 @@ static int s3c24xx_serial_initconsole(void) info = s3c2410_uart_inf_at; } else if (strcmp(dev->name, "s3c2440-uart") == 0) { info = s3c2440_uart_inf_at; + } else if (strcmp(dev->name, "s3c2412-uart") == 0) { + info = s3c2412_uart_inf_at; } else { printk(KERN_ERR "s3c24xx: no driver for %s\n", dev->name); return 0; @@ -1796,4 +1937,4 @@ console_initcall(s3c24xx_serial_initconsole); MODULE_LICENSE("GPL"); MODULE_AUTHOR("Ben Dooks "); -MODULE_DESCRIPTION("Samsung S3C2410/S3C2440 Serial port driver"); +MODULE_DESCRIPTION("Samsung S3C2410/S3C2440/S3C2412 Serial port driver"); diff --git a/include/asm-arm/arch-s3c2410/regs-serial.h b/include/asm-arm/arch-s3c2410/regs-serial.h index 83b01254c4..93f651ae29 100644 --- a/include/asm-arm/arch-s3c2410/regs-serial.h +++ b/include/asm-arm/arch-s3c2410/regs-serial.h @@ -82,6 +82,12 @@ #define S3C2440_UCON2_DIVMASK (7 << 12) #define S3C2440_UCON_DIVSHIFT (12) +#define S3C2412_UCON_CLKMASK (3<<10) +#define S3C2412_UCON_UCLK (1<<10) +#define S3C2412_UCON_USYSCLK (3<<10) +#define S3C2412_UCON_PCLK (0<<10) +#define S3C2412_UCON_PCLK2 (2<<10) + #define S3C2410_UCON_UCLK (1<<10) #define S3C2410_UCON_SBREAK (1<<4) @@ -124,6 +130,15 @@ #define S3C2410_UMCOM_AFC (1<<4) #define S3C2410_UMCOM_RTS_LOW (1<<0) +#define S3C2412_UMCON_AFC_63 (0<<5) +#define S3C2412_UMCON_AFC_56 (1<<5) +#define S3C2412_UMCON_AFC_48 (2<<5) +#define S3C2412_UMCON_AFC_40 (3<<5) +#define S3C2412_UMCON_AFC_32 (4<<5) +#define S3C2412_UMCON_AFC_24 (5<<5) +#define S3C2412_UMCON_AFC_16 (6<<5) +#define S3C2412_UMCON_AFC_8 (7<<5) + #define S3C2410_UFSTAT_TXFULL (1<<9) #define S3C2410_UFSTAT_RXFULL (1<<8) #define S3C2410_UFSTAT_TXMASK (15<<4) diff --git a/include/linux/serial_core.h b/include/linux/serial_core.h index 0ef50baa7d..951c4e8582 100644 --- a/include/linux/serial_core.h +++ b/include/linux/serial_core.h @@ -130,6 +130,9 @@ /* SUN4V Hypervisor Console */ #define PORT_SUNHV 72 +#define PORT_S3C2412 73 + + #ifdef __KERNEL__ #include