From: Jim Cromie Date: Mon, 26 Jun 2006 07:25:19 +0000 (-0700) Subject: [PATCH] GTOD: add scx200 HRT clocksource X-Git-Tag: v2.6.18-rc1~783 X-Git-Url: https://err.no/cgi-bin/gitweb.cgi?a=commitdiff_plain;h=6ae7440e6b7a46f4c119c60580aa9384c1b463f7;p=linux-2.6 [PATCH] GTOD: add scx200 HRT clocksource Add a GTOD clocksource driver based on the Geode SCx200's Hi-Res Timer. Signed-off-by: Jim Cromie Cc: Roman Zippel Cc: john stultz Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- diff --git a/arch/i386/Kconfig b/arch/i386/Kconfig index db1f8b4060..374fb50608 100644 --- a/arch/i386/Kconfig +++ b/arch/i386/Kconfig @@ -1050,13 +1050,23 @@ config SCx200 tristate "NatSemi SCx200 support" depends on !X86_VOYAGER help - This provides basic support for the National Semiconductor SCx200 - processor. Right now this is just a driver for the GPIO pins. + This provides basic support for National Semiconductor's + (now AMD's) Geode processors. The driver probes for the + PCI-IDs of several on-chip devices, so its a good dependency + for other scx200_* drivers. - If you don't know what to do here, say N. + If compiled as a module, the driver is named scx200. - This support is also available as a module. If compiled as a - module, it will be called scx200. +config SCx200HR_TIMER + tristate "NatSemi SCx200 27MHz High-Resolution Timer Support" + depends on SCx200 && GENERIC_TIME + default y + help + This driver provides a clocksource built upon the on-chip + 27MHz high-resolution timer. Its also a workaround for + NSC Geode SC-1100's buggy TSC, which loses time when the + processor goes idle (as is done by the scheduler). The + other workaround is idle=poll boot option. source "drivers/pcmcia/Kconfig" diff --git a/drivers/clocksource/Makefile b/drivers/clocksource/Makefile index be3511a308..a522254702 100644 --- a/drivers/clocksource/Makefile +++ b/drivers/clocksource/Makefile @@ -1,2 +1,3 @@ -obj-$(CONFIG_X86_CYCLONE_TIMER) += cyclone.o -obj-$(CONFIG_X86_PM_TIMER) += acpi_pm.o +obj-$(CONFIG_X86_CYCLONE_TIMER) += cyclone.o +obj-$(CONFIG_X86_PM_TIMER) += acpi_pm.o +obj-$(CONFIG_SCx200HR_TIMER) += scx200_hrt.o diff --git a/drivers/clocksource/scx200_hrt.c b/drivers/clocksource/scx200_hrt.c new file mode 100644 index 0000000000..d418b82972 --- /dev/null +++ b/drivers/clocksource/scx200_hrt.c @@ -0,0 +1,101 @@ +/* + * Copyright (C) 2006 Jim Cromie + * + * This is a clocksource driver for the Geode SCx200's 1 or 27 MHz + * high-resolution timer. The Geode SC-1100 (at least) has a buggy + * time stamp counter (TSC), which loses time unless 'idle=poll' is + * given as a boot-arg. In its absence, the Generic Timekeeping code + * will detect and de-rate the bad TSC, allowing this timer to take + * over timekeeping duties. + * + * Based on work by John Stultz, and Ted Phelps (in a 2.6.12-rc6 patch) + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + */ + +#include +#include +#include +#include +#include + +#define NAME "scx200_hrt" + +static int mhz27; +module_param(mhz27, int, 0); /* load time only */ +MODULE_PARM_DESC(mhz27, "count at 27.0 MHz (default is 1.0 MHz)"); + +static int ppm; +module_param(ppm, int, 0); /* load time only */ +MODULE_PARM_DESC(ppm, "+-adjust to actual XO freq (ppm)"); + +/* HiRes Timer configuration register address */ +#define SCx200_TMCNFG_OFFSET (SCx200_TIMER_OFFSET + 5) + +/* and config settings */ +#define HR_TMEN (1 << 0) /* timer interrupt enable */ +#define HR_TMCLKSEL (1 << 1) /* 1|0 counts at 27|1 MHz */ +#define HR_TM27MPD (1 << 2) /* 1 turns off input clock (power-down) */ + +/* The base timer frequency, * 27 if selected */ +#define HRT_FREQ 1000000 + +static cycle_t read_hrt(void) +{ + /* Read the timer value */ + return (cycle_t) inl(scx200_cb_base + SCx200_TIMER_OFFSET); +} + +#define HRT_SHIFT_1 22 +#define HRT_SHIFT_27 26 + +static struct clocksource cs_hrt = { + .name = "scx200_hrt", + .rating = 250, + .read = read_hrt, + .mask = CLOCKSOURCE_MASK(32), + .is_continuous = 1, + /* mult, shift are set based on mhz27 flag */ +}; + +static int __init init_hrt_clocksource(void) +{ + /* Make sure scx200 has initializedd the configuration block */ + if (!scx200_cb_present()) + return -ENODEV; + + /* Reserve the timer's ISA io-region for ourselves */ + if (!request_region(scx200_cb_base + SCx200_TIMER_OFFSET, + SCx200_TIMER_SIZE, + "NatSemi SCx200 High-Resolution Timer")) { + printk(KERN_WARNING NAME ": unable to lock timer region\n"); + return -ENODEV; + } + + /* write timer config */ + outb(HR_TMEN | (mhz27) ? HR_TMCLKSEL : 0, + scx200_cb_base + SCx200_TMCNFG_OFFSET); + + if (mhz27) { + cs_hrt.shift = HRT_SHIFT_27; + cs_hrt.mult = clocksource_hz2mult((HRT_FREQ + ppm) * 27, + cs_hrt.shift); + } else { + cs_hrt.shift = HRT_SHIFT_1; + cs_hrt.mult = clocksource_hz2mult(HRT_FREQ + ppm, + cs_hrt.shift); + } + printk(KERN_INFO "enabling scx200 high-res timer (%s MHz +%d ppm)\n", + mhz27 ? "27":"1", ppm); + + return clocksource_register(&cs_hrt); +} + +module_init(init_hrt_clocksource); + +MODULE_AUTHOR("Jim Cromie "); +MODULE_DESCRIPTION("clocksource on SCx200 HiRes Timer"); +MODULE_LICENSE("GPL");