From: sedji gaouaou Date: Thu, 10 Jul 2008 09:15:35 +0000 (+0100) Subject: [ARM] 5130/4: Support for the at91sam9g20 X-Git-Tag: v2.6.27-rc1~850^2~2^2~1 X-Git-Url: https://err.no/cgi-bin/gitweb.cgi?a=commitdiff_plain;h=613526677a74c2b3d1b1696ea7334b2cf35155b3;p=linux-2.6 [ARM] 5130/4: Support for the at91sam9g20 Support for the at91sam9g20 : Atmel 400Mhz ARM 926ej-s SOC. AT91sam9g20 is an evolution of the at91sam9260 with a faster clock speed. We created a new board for this device but based the chip support directly on 9260 files with little updates. Here is the chip page on Atmel wabsite: http://atmel.com/dyn/products/product_card.asp?part_id=4337 Signed-off-by: Sedji Gaouaou Signed-off-by: Justin Waters Acked-by: Andrew Victor Signed-off-by: Russell King --- diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig index cae5c67dc3..5bad6b9b00 100644 --- a/arch/arm/mach-at91/Kconfig +++ b/arch/arm/mach-at91/Kconfig @@ -30,6 +30,11 @@ config ARCH_AT91SAM9RL select GENERIC_TIME select GENERIC_CLOCKEVENTS +config ARCH_AT91SAM9G20 + bool "AT91SAM9G20" + select GENERIC_TIME + select GENERIC_CLOCKEVENTS + config ARCH_AT91CAP9 bool "AT91CAP9" select GENERIC_TIME @@ -239,6 +244,20 @@ endif # ---------------------------------------------------------- +if ARCH_AT91SAM9G20 + +comment "AT91SAM9G20 Board Type" + +config MACH_AT91SAM9G20EK + bool "Atmel AT91SAM9G20-EK Evaluation Kit" + depends on ARCH_AT91SAM9G20 + help + Select this if you are using Atmel's AT91SAM9G20-EK Evaluation Kit. + +endif + +# ---------------------------------------------------------- + if ARCH_AT91CAP9 comment "AT91CAP9 Board Type" @@ -274,13 +293,13 @@ comment "AT91 Board Options" config MTD_AT91_DATAFLASH_CARD bool "Enable DataFlash Card support" - depends on (ARCH_AT91RM9200DK || MACH_AT91RM9200EK || MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9263EK || MACH_AT91CAP9ADK || MACH_SAM9_L9260 || MACH_ECBAT91) + depends on (ARCH_AT91RM9200DK || MACH_AT91RM9200EK || MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9263EK || MACH_AT91SAM9G20EK || MACH_ECBAT91 || MACH_SAM9_L9260 || MACH_AT91CAP9ADK) help Enable support for the DataFlash card. config MTD_NAND_AT91_BUSWIDTH_16 bool "Enable 16-bit data bus interface to NAND flash" - depends on (MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9263EK || MACH_AT91CAP9ADK) + depends on (MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9263EK || MACH_AT91SAM9G20EK || MACH_AT91CAP9ADK) help On AT91SAM926x boards both types of NAND flash can be present (8 and 16 bit data bus width). @@ -329,15 +348,15 @@ config AT91_EARLY_USART2 config AT91_EARLY_USART3 bool "USART3" - depends on (ARCH_AT91RM9200 || ARCH_AT91SAM9RL || ARCH_AT91SAM9260) + depends on (ARCH_AT91RM9200 || ARCH_AT91SAM9RL || ARCH_AT91SAM9260 || ARCH_AT91SAM9G20) config AT91_EARLY_USART4 bool "USART4" - depends on ARCH_AT91SAM9260 + depends on ARCH_AT91SAM9260 || ARCH_AT91SAM9G20 config AT91_EARLY_USART5 bool "USART5" - depends on ARCH_AT91SAM9260 + depends on ARCH_AT91SAM9260 || ARCH_AT91SAM9G20 endchoice diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile index 932d17109e..7d641f9751 100644 --- a/arch/arm/mach-at91/Makefile +++ b/arch/arm/mach-at91/Makefile @@ -15,6 +15,7 @@ obj-$(CONFIG_ARCH_AT91SAM9260) += at91sam9260.o at91sam926x_time.o at91sam9260_d obj-$(CONFIG_ARCH_AT91SAM9261) += at91sam9261.o at91sam926x_time.o at91sam9261_devices.o obj-$(CONFIG_ARCH_AT91SAM9263) += at91sam9263.o at91sam926x_time.o at91sam9263_devices.o obj-$(CONFIG_ARCH_AT91SAM9RL) += at91sam9rl.o at91sam926x_time.o at91sam9rl_devices.o +obj-$(CONFIG_ARCH_AT91SAM9G20) += at91sam9260.o at91sam926x_time.o at91sam9260_devices.o obj-$(CONFIG_ARCH_AT91CAP9) += at91cap9.o at91sam926x_time.o at91cap9_devices.o obj-$(CONFIG_ARCH_AT91X40) += at91x40.o at91x40_time.o @@ -49,6 +50,9 @@ obj-$(CONFIG_MACH_USB_A9263) += board-usb-a9263.o # AT91SAM9RL board-specific support obj-$(CONFIG_MACH_AT91SAM9RLEK) += board-sam9rlek.o +# AT91SAM9G20 board-specific support +obj-$(CONFIG_MACH_AT91SAM9G20EK) += board-sam9g20ek.o + # AT91CAP9 board-specific support obj-$(CONFIG_MACH_AT91CAP9ADK) += board-cap9adk.o diff --git a/arch/arm/mach-at91/at91sam9260.c b/arch/arm/mach-at91/at91sam9260.c index ee26550cdc..380f12a122 100644 --- a/arch/arm/mach-at91/at91sam9260.c +++ b/arch/arm/mach-at91/at91sam9260.c @@ -47,6 +47,20 @@ static struct map_desc at91sam9260_sram_desc[] __initdata = { } }; +static struct map_desc at91sam9g20_sram_desc[] __initdata = { + { + .virtual = AT91_IO_VIRT_BASE - AT91SAM9G20_SRAM0_SIZE, + .pfn = __phys_to_pfn(AT91SAM9G20_SRAM0_BASE), + .length = AT91SAM9G20_SRAM0_SIZE, + .type = MT_DEVICE, + }, { + .virtual = AT91_IO_VIRT_BASE - AT91SAM9G20_SRAM0_SIZE - AT91SAM9G20_SRAM1_SIZE, + .pfn = __phys_to_pfn(AT91SAM9G20_SRAM1_BASE), + .length = AT91SAM9G20_SRAM1_SIZE, + .type = MT_DEVICE, + } +}; + static struct map_desc at91sam9xe_sram_desc[] __initdata = { { .pfn = __phys_to_pfn(AT91SAM9XE_SRAM_BASE), @@ -307,6 +321,8 @@ void __init at91sam9260_initialize(unsigned long main_clock) if (cpu_is_at91sam9xe()) at91sam9xe_initialize(); + else if (cpu_is_at91sam9g20()) + iotable_init(at91sam9g20_sram_desc, ARRAY_SIZE(at91sam9g20_sram_desc)); else iotable_init(at91sam9260_sram_desc, ARRAY_SIZE(at91sam9260_sram_desc)); diff --git a/arch/arm/mach-at91/at91sam9260_devices.c b/arch/arm/mach-at91/at91sam9260_devices.c index 26f5cacbec..86cba4ac29 100644 --- a/arch/arm/mach-at91/at91sam9260_devices.c +++ b/arch/arm/mach-at91/at91sam9260_devices.c @@ -18,6 +18,7 @@ #include #include +#include #include #include #include @@ -320,20 +321,41 @@ void __init at91_add_device_nand(struct at91_nand_data *data) csa = at91_sys_read(AT91_MATRIX_EBICSA); at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA); - /* set the bus interface characteristics */ - at91_sys_write(AT91_SMC_SETUP(3), AT91_SMC_NWESETUP_(1) | AT91_SMC_NCS_WRSETUP_(0) - | AT91_SMC_NRDSETUP_(1) | AT91_SMC_NCS_RDSETUP_(0)); + if (cpu_is_at91sam9260()) { + /* Timing for sam9260 */ + /* set the bus interface characteristics */ + at91_sys_write(AT91_SMC_SETUP(3), AT91_SMC_NWESETUP_(1) | AT91_SMC_NCS_WRSETUP_(0) + | AT91_SMC_NRDSETUP_(1) | AT91_SMC_NCS_RDSETUP_(0)); - at91_sys_write(AT91_SMC_PULSE(3), AT91_SMC_NWEPULSE_(3) | AT91_SMC_NCS_WRPULSE_(3) - | AT91_SMC_NRDPULSE_(3) | AT91_SMC_NCS_RDPULSE_(3)); + at91_sys_write(AT91_SMC_PULSE(3), AT91_SMC_NWEPULSE_(3) | AT91_SMC_NCS_WRPULSE_(3) + | AT91_SMC_NRDPULSE_(3) | AT91_SMC_NCS_RDPULSE_(3)); - at91_sys_write(AT91_SMC_CYCLE(3), AT91_SMC_NWECYCLE_(5) | AT91_SMC_NRDCYCLE_(5)); + at91_sys_write(AT91_SMC_CYCLE(3), AT91_SMC_NWECYCLE_(5) | AT91_SMC_NRDCYCLE_(5)); - if (data->bus_width_16) - mode = AT91_SMC_DBW_16; - else - mode = AT91_SMC_DBW_8; - at91_sys_write(AT91_SMC_MODE(3), mode | AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_TDF_(2)); + if (data->bus_width_16) + mode = AT91_SMC_DBW_16; + else + mode = AT91_SMC_DBW_8; + at91_sys_write(AT91_SMC_MODE(3), mode | AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_TDF_(2)); + } + + if (cpu_is_at91sam9g20()) { + /* Timing for sam9g20 */ + /* set the bus interface characteristics */ + at91_sys_write(AT91_SMC_SETUP(3), AT91_SMC_NWESETUP_(2) | AT91_SMC_NCS_WRSETUP_(0) + | AT91_SMC_NRDSETUP_(2) | AT91_SMC_NCS_RDSETUP_(0)); + + at91_sys_write(AT91_SMC_PULSE(3), AT91_SMC_NWEPULSE_(4) | AT91_SMC_NCS_WRPULSE_(4) + | AT91_SMC_NRDPULSE_(4) | AT91_SMC_NCS_RDPULSE_(4)); + + at91_sys_write(AT91_SMC_CYCLE(3), AT91_SMC_NWECYCLE_(7) | AT91_SMC_NRDCYCLE_(7)); + + if (data->bus_width_16) + mode = AT91_SMC_DBW_16; + else + mode = AT91_SMC_DBW_8; + at91_sys_write(AT91_SMC_MODE(3), mode | AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_TDF_(3)); + } /* enable pin */ if (data->enable_pin) diff --git a/arch/arm/mach-at91/board-sam9g20ek.c b/arch/arm/mach-at91/board-sam9g20ek.c new file mode 100644 index 0000000000..45617c2012 --- /dev/null +++ b/arch/arm/mach-at91/board-sam9g20ek.c @@ -0,0 +1,218 @@ +/* + * Copyright (C) 2005 SAN People + * Copyright (C) 2008 Atmel + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include + +#include +#include +#include + +#include +#include + +#include "generic.h" + + +static void __init ek_map_io(void) +{ + /* Initialize processor: 18.432 MHz crystal */ + at91sam9260_initialize(18432000); + + /* DGBU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS + | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD + | ATMEL_UART_RI); + + /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */ + at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS); + + /* set serial console to ttyS0 (ie, DBGU) */ + at91_set_serial_console(0); +} + +static void __init ek_init_irq(void) +{ + at91sam9260_init_interrupts(NULL); +} + + +/* + * USB Host port + */ +static struct at91_usbh_data __initdata ek_usbh_data = { + .ports = 2, +}; + +/* + * USB Device port + */ +static struct at91_udc_data __initdata ek_udc_data = { + .vbus_pin = AT91_PIN_PC5, + .pullup_pin = 0, /* pull-up driven by UDC */ +}; + + +/* + * SPI devices. + */ +static struct spi_board_info ek_spi_devices[] = { +#if !defined(CONFIG_MMC_AT91) + { /* DataFlash chip */ + .modalias = "mtd_dataflash", + .chip_select = 1, + .max_speed_hz = 15 * 1000 * 1000, + .bus_num = 0, + }, +#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD) + { /* DataFlash card */ + .modalias = "mtd_dataflash", + .chip_select = 0, + .max_speed_hz = 15 * 1000 * 1000, + .bus_num = 0, + }, +#endif +#endif +}; + + +/* + * MACB Ethernet device + */ +static struct at91_eth_data __initdata ek_macb_data = { + .phy_irq_pin = AT91_PIN_PA7, + .is_rmii = 1, +}; + + +/* + * NAND flash + */ +static struct mtd_partition __initdata ek_nand_partition[] = { + { + .name = "Bootstrap", + .offset = 0, + .size = 4 * 1024 * 1024, + }, + { + .name = "Partition 1", + .offset = 4 * 1024 * 1024, + .size = 60 * 1024 * 1024, + }, + { + .name = "Partition 2", + .offset = 64 * 1024 * 1024, + .size = MTDPART_SIZ_FULL, + }, +}; + +static struct mtd_partition * __init nand_partitions(int size, int *num_partitions) +{ + *num_partitions = ARRAY_SIZE(ek_nand_partition); + return ek_nand_partition; +} + +/* det_pin is not connected */ +static struct at91_nand_data __initdata ek_nand_data = { + .ale = 21, + .cle = 22, + .rdy_pin = AT91_PIN_PC13, + .enable_pin = AT91_PIN_PC14, + .partition_info = nand_partitions, +#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16) + .bus_width_16 = 1, +#else + .bus_width_16 = 0, +#endif +}; + + +/* + * MCI (SD/MMC) + * det_pin, wp_pin and vcc_pin are not connected + */ +static struct at91_mmc_data __initdata ek_mmc_data = { + .slot_b = 1, + .wire4 = 1, +}; + + +/* + * LEDs + */ +static struct gpio_led ek_leds[] = { + { /* "bottom" led, green, userled1 to be defined */ + .name = "ds5", + .gpio = AT91_PIN_PA6, + .active_low = 1, + .default_trigger = "none", + }, + { /* "power" led, yellow */ + .name = "ds1", + .gpio = AT91_PIN_PA9, + .default_trigger = "heartbeat", + } +}; + +static void __init ek_board_init(void) +{ + /* Serial */ + at91_add_device_serial(); + /* USB Host */ + at91_add_device_usbh(&ek_usbh_data); + /* USB Device */ + at91_add_device_udc(&ek_udc_data); + /* SPI */ + at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices)); + /* NAND */ + at91_add_device_nand(&ek_nand_data); + /* Ethernet */ + at91_add_device_eth(&ek_macb_data); + /* MMC */ + at91_add_device_mmc(0, &ek_mmc_data); + /* I2C */ + at91_add_device_i2c(NULL, 0); + /* LEDs */ + at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds)); +} + +MACHINE_START(AT91SAM9G20EK, "Atmel AT91SAM9G20-EK") + /* Maintainer: Atmel */ + .phys_io = AT91_BASE_SYS, + .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, + .boot_params = AT91_SDRAM_BASE + 0x100, + .timer = &at91sam926x_timer, + .map_io = ek_map_io, + .init_irq = ek_init_irq, + .init_machine = ek_board_init, +MACHINE_END diff --git a/arch/arm/mach-at91/clock.c b/arch/arm/mach-at91/clock.c index e8ce8f0f3e..464bdbbf74 100644 --- a/arch/arm/mach-at91/clock.c +++ b/arch/arm/mach-at91/clock.c @@ -515,14 +515,19 @@ static unsigned __init at91_pll_calc(unsigned main_freq, unsigned out_freq) /* * PLL input between 1MHz and 32MHz per spec, but lower * frequences seem necessary in some cases so allow 100K. + * Warning: some newer products need 2MHz min. */ input = main_freq / i; + if (cpu_is_at91sam9g20() && input < 2000000) + continue; if (input < 100000) continue; if (input > 32000000) continue; mul1 = out_freq / input; + if (cpu_is_at91sam9g20() && mul > 63) + continue; if (mul1 > 2048) continue; if (mul1 < 2) @@ -582,7 +587,8 @@ int __init at91_clock_init(unsigned long main_clock) /* report if PLLA is more than mildly overclocked */ plla.rate_hz = at91_pll_rate(&plla, main_clock, at91_sys_read(AT91_CKGR_PLLAR)); - if (plla.rate_hz > 209000000) + if ((!cpu_is_at91sam9g20() && plla.rate_hz > 209000000) + || (cpu_is_at91sam9g20() && plla.rate_hz > 800000000)) pr_info("Clocks: PLLA overclocked, %ld MHz\n", plla.rate_hz / 1000000); /* @@ -597,7 +603,7 @@ int __init at91_clock_init(unsigned long main_clock) uhpck.pmc_mask = AT91RM9200_PMC_UHP; udpck.pmc_mask = AT91RM9200_PMC_UDP; at91_sys_write(AT91_PMC_SCER, AT91RM9200_PMC_MCKUDP); - } else if (cpu_is_at91sam9260() || cpu_is_at91sam9261() || cpu_is_at91sam9263()) { + } else if (cpu_is_at91sam9260() || cpu_is_at91sam9261() || cpu_is_at91sam9263() || cpu_is_at91sam9g20()) { uhpck.pmc_mask = AT91SAM926x_PMC_UHP; udpck.pmc_mask = AT91SAM926x_PMC_UDP; } else if (cpu_is_at91cap9()) { @@ -629,8 +635,13 @@ int __init at91_clock_init(unsigned long main_clock) freq /= (1 << ((mckr & AT91_PMC_PRES) >> 2)); /* prescale */ if (cpu_is_at91rm9200()) mck.rate_hz = freq / (1 + ((mckr & AT91_PMC_MDIV) >> 8)); /* mdiv */ - else - mck.rate_hz = freq / (1 << ((mckr & AT91_PMC_MDIV) >> 8)); /* mdiv */ + else if (cpu_is_at91sam9g20()) { + mck.rate_hz = (mckr & AT91_PMC_MDIV) ? + freq / ((mckr & AT91_PMC_MDIV) >> 7) : freq; /* mdiv ; (x >> 7) = ((x >> 8) * 2) */ + if (mckr & AT91_PMC_PDIV) + freq /= 2; /* processor clock division */ + } else + mck.rate_hz = freq / (1 << ((mckr & AT91_PMC_MDIV) >> 8)); /* mdiv */ /* Register the PMC's standard clocks */ for (i = 0; i < ARRAY_SIZE(standard_pmc_clocks); i++) diff --git a/arch/arm/mach-at91/pm.c b/arch/arm/mach-at91/pm.c index aa863c1577..8ab4feb1ec 100644 --- a/arch/arm/mach-at91/pm.c +++ b/arch/arm/mach-at91/pm.c @@ -202,7 +202,7 @@ static int at91_pm_verify_clocks(void) pr_debug("AT91: PM - Suspend-to-RAM with USB still active\n"); return 0; } - } else if (cpu_is_at91sam9260() || cpu_is_at91sam9261() || cpu_is_at91sam9263()) { + } else if (cpu_is_at91sam9260() || cpu_is_at91sam9261() || cpu_is_at91sam9263() || cpu_is_at91sam9g20()) { if ((scsr & (AT91SAM926x_PMC_UHP | AT91SAM926x_PMC_UDP)) != 0) { pr_debug("AT91: PM - Suspend-to-RAM with USB still active\n"); return 0; diff --git a/arch/arm/mm/Kconfig b/arch/arm/mm/Kconfig index 33ed048502..750d895cd2 100644 --- a/arch/arm/mm/Kconfig +++ b/arch/arm/mm/Kconfig @@ -180,8 +180,8 @@ config CPU_ARM925T # ARM926T config CPU_ARM926T bool "Support ARM926T processor" - depends on ARCH_INTEGRATOR || ARCH_VERSATILE_PB || MACH_VERSATILE_AB || ARCH_OMAP730 || ARCH_OMAP16XX || MACH_REALVIEW_EB || ARCH_PNX4008 || ARCH_NETX || CPU_S3C2412 || ARCH_AT91SAM9260 || ARCH_AT91SAM9261 || ARCH_AT91SAM9263 || ARCH_AT91SAM9RL || ARCH_AT91CAP9 || ARCH_NS9XXX || ARCH_DAVINCI - default y if ARCH_VERSATILE_PB || MACH_VERSATILE_AB || ARCH_OMAP730 || ARCH_OMAP16XX || ARCH_PNX4008 || ARCH_NETX || CPU_S3C2412 || ARCH_AT91SAM9260 || ARCH_AT91SAM9261 || ARCH_AT91SAM9263 || ARCH_AT91SAM9RL || ARCH_AT91CAP9 || ARCH_NS9XXX || ARCH_DAVINCI + depends on ARCH_INTEGRATOR || ARCH_VERSATILE_PB || MACH_VERSATILE_AB || ARCH_OMAP730 || ARCH_OMAP16XX || MACH_REALVIEW_EB || ARCH_PNX4008 || ARCH_NETX || CPU_S3C2412 || ARCH_AT91SAM9260 || ARCH_AT91SAM9261 || ARCH_AT91SAM9263 || ARCH_AT91SAM9RL || ARCH_AT91SAM9G20 || ARCH_AT91CAP9 || ARCH_NS9XXX || ARCH_DAVINCI + default y if ARCH_VERSATILE_PB || MACH_VERSATILE_AB || ARCH_OMAP730 || ARCH_OMAP16XX || ARCH_PNX4008 || ARCH_NETX || CPU_S3C2412 || ARCH_AT91SAM9260 || ARCH_AT91SAM9261 || ARCH_AT91SAM9263 || ARCH_AT91SAM9RL || ARCH_AT91SAM9G20 || ARCH_AT91CAP9 || ARCH_NS9XXX || ARCH_DAVINCI select CPU_32v5 select CPU_ABRT_EV5TJ select CPU_PABRT_NOIFAR diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig index 9f6cc8a560..be3b13cf41 100644 --- a/drivers/net/Kconfig +++ b/drivers/net/Kconfig @@ -217,7 +217,7 @@ config MII config MACB tristate "Atmel MACB support" - depends on AVR32 || ARCH_AT91SAM9260 || ARCH_AT91SAM9263 || ARCH_AT91CAP9 + depends on AVR32 || ARCH_AT91SAM9260 || ARCH_AT91SAM9263 || ARCH_AT91SAM9G20 || ARCH_AT91CAP9 select PHYLIB help The Atmel MACB ethernet interface is found on many AT32 and AT91 diff --git a/drivers/usb/gadget/at91_udc.c b/drivers/usb/gadget/at91_udc.c index 274c60a970..b6b2a0a5ba 100644 --- a/drivers/usb/gadget/at91_udc.c +++ b/drivers/usb/gadget/at91_udc.c @@ -888,7 +888,7 @@ static void pullup(struct at91_udc *udc, int is_on) at91_udp_write(udc, AT91_UDP_TXVC, 0); if (cpu_is_at91rm9200()) gpio_set_value(udc->board.pullup_pin, active); - else if (cpu_is_at91sam9260() || cpu_is_at91sam9263()) { + else if (cpu_is_at91sam9260() || cpu_is_at91sam9263() || cpu_is_at91sam9g20()) { u32 txvc = at91_udp_read(udc, AT91_UDP_TXVC); txvc |= AT91_UDP_TXVC_PUON; @@ -906,7 +906,7 @@ static void pullup(struct at91_udc *udc, int is_on) at91_udp_write(udc, AT91_UDP_TXVC, AT91_UDP_TXVC_TXVDIS); if (cpu_is_at91rm9200()) gpio_set_value(udc->board.pullup_pin, !active); - else if (cpu_is_at91sam9260() || cpu_is_at91sam9263()) { + else if (cpu_is_at91sam9260() || cpu_is_at91sam9263() || cpu_is_at91sam9g20()) { u32 txvc = at91_udp_read(udc, AT91_UDP_TXVC); txvc &= ~AT91_UDP_TXVC_PUON; diff --git a/include/asm-arm/arch-at91/at91sam9260.h b/include/asm-arm/arch-at91/at91sam9260.h index c8934fe34d..889872a3f2 100644 --- a/include/asm-arm/arch-at91/at91sam9260.h +++ b/include/asm-arm/arch-at91/at91sam9260.h @@ -6,6 +6,8 @@ * Common definitions. * Based on AT91SAM9260 datasheet revision A (Preliminary). * + * Includes also definitions for AT91SAM9XE and AT91SAM9G families + * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation; either version 2 of the License, or @@ -123,5 +125,14 @@ #define AT91SAM9XE_FLASH_BASE 0x00200000 /* Internal FLASH base address */ #define AT91SAM9XE_SRAM_BASE 0x00300000 /* Internal SRAM base address */ +#define AT91SAM9G20_ROM_BASE 0x00100000 /* Internal ROM base address */ +#define AT91SAM9G20_ROM_SIZE SZ_32K /* Internal ROM size (32Kb) */ + +#define AT91SAM9G20_SRAM0_BASE 0x00200000 /* Internal SRAM 0 base address */ +#define AT91SAM9G20_SRAM0_SIZE SZ_16K /* Internal SRAM 0 size (16Kb) */ +#define AT91SAM9G20_SRAM1_BASE 0x00300000 /* Internal SRAM 1 base address */ +#define AT91SAM9G20_SRAM1_SIZE SZ_16K /* Internal SRAM 1 size (16Kb) */ + +#define AT91SAM9G20_UHP_BASE 0x00500000 /* USB Host controller */ #endif diff --git a/include/asm-arm/arch-at91/board.h b/include/asm-arm/arch-at91/board.h index 1f24702868..94de788da7 100644 --- a/include/asm-arm/arch-at91/board.h +++ b/include/asm-arm/arch-at91/board.h @@ -77,7 +77,7 @@ struct at91_eth_data { }; extern void __init at91_add_device_eth(struct at91_eth_data *data); -#if defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9263) || defined(CONFIG_ARCH_AT91CAP9) +#if defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9263) || defined(CONFIG_ARCH_AT91SAM9G20) || defined(CONFIG_ARCH_AT91CAP9) #define eth_platform_data at91_eth_data #endif diff --git a/include/asm-arm/arch-at91/cpu.h b/include/asm-arm/arch-at91/cpu.h index 7145166826..52df794205 100644 --- a/include/asm-arm/arch-at91/cpu.h +++ b/include/asm-arm/arch-at91/cpu.h @@ -21,6 +21,7 @@ #define ARCH_ID_AT91SAM9260 0x019803a0 #define ARCH_ID_AT91SAM9261 0x019703a0 #define ARCH_ID_AT91SAM9263 0x019607a0 +#define ARCH_ID_AT91SAM9G20 0x019905a0 #define ARCH_ID_AT91SAM9RL64 0x019b03a0 #define ARCH_ID_AT91CAP9 0x039A03A0 @@ -63,6 +64,12 @@ static inline unsigned long at91_arch_identify(void) #define cpu_is_at91sam9260() (0) #endif +#ifdef CONFIG_ARCH_AT91SAM9G20 +#define cpu_is_at91sam9g20() (at91_cpu_identify() == ARCH_ID_AT91SAM9G20) +#else +#define cpu_is_at91sam9g20() (0) +#endif + #ifdef CONFIG_ARCH_AT91SAM9261 #define cpu_is_at91sam9261() (at91_cpu_identify() == ARCH_ID_AT91SAM9261) #else diff --git a/include/asm-arm/arch-at91/hardware.h b/include/asm-arm/arch-at91/hardware.h index 2c826d8247..016a3a3f66 100644 --- a/include/asm-arm/arch-at91/hardware.h +++ b/include/asm-arm/arch-at91/hardware.h @@ -18,7 +18,7 @@ #if defined(CONFIG_ARCH_AT91RM9200) #include -#elif defined(CONFIG_ARCH_AT91SAM9260) +#elif defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9G20) #include #elif defined(CONFIG_ARCH_AT91SAM9261) #include diff --git a/include/asm-arm/arch-at91/timex.h b/include/asm-arm/arch-at91/timex.h index 6e084eb839..298d8313cd 100644 --- a/include/asm-arm/arch-at91/timex.h +++ b/include/asm-arm/arch-at91/timex.h @@ -57,6 +57,11 @@ #define AT91SAM9_MASTER_CLOCK 100000000 #define CLOCK_TICK_RATE (AT91SAM9_MASTER_CLOCK/16) +#elif defined(CONFIG_ARCH_AT91SAM9G20) + +#define AT91SAM9_MASTER_CLOCK 132096000 +#define CLOCK_TICK_RATE (AT91SAM9_MASTER_CLOCK/16) + #elif defined(CONFIG_ARCH_AT91CAP9) #define AT91CAP9_MASTER_CLOCK 100000000 diff --git a/sound/soc/at91/at91-ssc.c b/sound/soc/at91/at91-ssc.c index bc35d00a38..1a42609501 100644 --- a/sound/soc/at91/at91-ssc.c +++ b/sound/soc/at91/at91-ssc.c @@ -41,7 +41,7 @@ #define DBG(x...) #endif -#if defined(CONFIG_ARCH_AT91SAM9260) +#if defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9G20) #define NUM_SSC_DEVICES 1 #else #define NUM_SSC_DEVICES 3