From: Ben Cahill <ben.m.cahill@intel.com>
Date: Thu, 29 Nov 2007 03:10:01 +0000 (+0800)
Subject: iwlwifi: document temperature calculation
X-Git-Tag: v2.6.25-rc1~1162^2~489
X-Git-Url: https://err.no/cgi-bin/gitweb.cgi?a=commitdiff_plain;h=5991b419f04dee78c36d43de6b6ff2d27934d707;p=linux-2.6

iwlwifi: document temperature calculation

Document temperature calculation

Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
---

diff --git a/drivers/net/wireless/iwlwifi/iwl-4965-hw.h b/drivers/net/wireless/iwlwifi/iwl-4965-hw.h
index 3c09225c66..78d9854f75 100644
--- a/drivers/net/wireless/iwlwifi/iwl-4965-hw.h
+++ b/drivers/net/wireless/iwlwifi/iwl-4965-hw.h
@@ -645,21 +645,43 @@ static inline int iwl4965_hw_valid_rtc_data_addr(u32 addr)
 	       (addr < KDR_RTC_DATA_UPPER_BOUND);
 }
 
-/********************* START TXPOWER *****************************************/
-
-enum {
-	CALIB_CH_GROUP_1 = 0,
-	CALIB_CH_GROUP_2 = 1,
-	CALIB_CH_GROUP_3 = 2,
-	CALIB_CH_GROUP_4 = 3,
-	CALIB_CH_GROUP_5 = 4,
-	CALIB_CH_GROUP_MAX
-};
+/********************* START TEMPERATURE *************************************/
 
-/* Temperature calibration offset is 3% 0C in Kelvin */
+/*
+ * 4965 temperature calculation.
+ *
+ * The driver must calculate the device temperature before calculating
+ * a txpower setting (amplifier gain is temperature dependent).  The
+ * calculation uses 4 measurements, 3 of which (R1, R2, R3) are calibration
+ * values used for the life of the driver, and one of which (R4) is the
+ * real-time temperature indicator.
+ *
+ * uCode provides all 4 values to the driver via the "initialize alive"
+ * notification (see struct iwl4965_init_alive_resp).  After the runtime uCode
+ * image loads, uCode updates the R4 value via statistics notifications
+ * (see STATISTICS_NOTIFICATION), which occur after each received beacon
+ * when associated, or can be requested via REPLY_STATISTICS_CMD.
+ *
+ * NOTE:  uCode provides the R4 value as a 23-bit signed value.  Driver
+ *        must sign-extend to 32 bits before applying formula below.
+ *
+ * Formula:
+ *
+ * degrees Kelvin = ((97 * 259 * (R4 - R2) / (R3 - R1)) / 100) + 8
+ *
+ * NOTE:  The basic formula is 259 * (R4-R2) / (R3-R1).  The 97/100 is
+ * an additional correction, which should be centered around 0 degrees
+ * Celsius (273 degrees Kelvin).  The 8 (3 percent of 273) compensates for
+ * centering the 97/100 correction around 0 degrees K.
+ *
+ * Add 273 to Kelvin value to find degrees Celsius, for comparing current
+ * temperature with factory-measured temperatures when calculating txpower
+ * settings.
+ */
 #define TEMPERATURE_CALIB_KELVIN_OFFSET 8
 #define TEMPERATURE_CALIB_A_VAL 259
 
+/* Limit range of calculated temperature to be between these Kelvin values */
 #define IWL_TX_POWER_TEMPERATURE_MIN  (263)
 #define IWL_TX_POWER_TEMPERATURE_MAX  (410)
 
@@ -667,6 +689,19 @@ enum {
 	(((t) < IWL_TX_POWER_TEMPERATURE_MIN) || \
 	 ((t) > IWL_TX_POWER_TEMPERATURE_MAX))
 
+/********************* END TEMPERATURE ***************************************/
+
+/********************* START TXPOWER *****************************************/
+
+enum {
+	CALIB_CH_GROUP_1 = 0,
+	CALIB_CH_GROUP_2 = 1,
+	CALIB_CH_GROUP_3 = 2,
+	CALIB_CH_GROUP_4 = 3,
+	CALIB_CH_GROUP_5 = 4,
+	CALIB_CH_GROUP_MAX
+};
+
 #define IWL_TX_POWER_MIMO_REGULATORY_COMPENSATION (6)
 
 #define IWL_TX_POWER_TARGET_POWER_MIN       (0)	/* 0 dBm = 1 milliwatt */