From: Thomas Gleixner <tglx@linutronix.de>
Date: Fri, 2 May 2008 19:24:30 +0000 (+0200)
Subject: x86: undo visws/numaq build changes
X-Git-Tag: v2.6.26-rc2~76^2~12
X-Git-Url: https://err.no/cgi-bin/gitweb.cgi?a=commitdiff_plain;h=48b83d2425d7781bb625b1c37b5f2a8963b6e23b;p=linux-2.6

x86: undo visws/numaq build changes

arch/x86/pci/Makefile_32 has a nasty detail. VISWS and NUMAQ build
override the generic pci-y rules. This needs a proper cleanup, but
that needs more thoughts. Undo

commit 895d30935ebe05f192e844792668bf8d19deaae7
    x86: numaq fix
    do not override the existing pci-y rule when adding visws or
    numaq rules.

There is also a stupid init function ordering problem vs. acpi.o

Add comments to the Makefile to avoid tripping over this again.

Remove the srat stub code in discontig_32.c to allow a proper NUMAQ
build.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---

diff --git a/arch/x86/mm/discontig_32.c b/arch/x86/mm/discontig_32.c
index 18378850e2..914ccf9836 100644
--- a/arch/x86/mm/discontig_32.c
+++ b/arch/x86/mm/discontig_32.c
@@ -476,29 +476,3 @@ int memory_add_physaddr_to_nid(u64 addr)
 
 EXPORT_SYMBOL_GPL(memory_add_physaddr_to_nid);
 #endif
-
-#ifndef CONFIG_HAVE_ARCH_PARSE_SRAT
-/*
- * XXX FIXME: Make SLIT table parsing available to 32-bit NUMA
- *
- * These stub functions are needed to compile 32-bit NUMA when SRAT is
- * not set. There are functions in srat_64.c for parsing this table
- * and it may be possible to make them common functions.
- */
-void acpi_numa_slit_init (struct acpi_table_slit *slit)
-{
-	printk(KERN_INFO "ACPI: No support for parsing SLIT table\n");
-}
-
-void acpi_numa_processor_affinity_init (struct acpi_srat_cpu_affinity *pa)
-{
-}
-
-void acpi_numa_memory_affinity_init (struct acpi_srat_mem_affinity *ma)
-{
-}
-
-void acpi_numa_arch_fixup(void)
-{
-}
-#endif /* CONFIG_HAVE_ARCH_PARSE_SRAT */
diff --git a/arch/x86/pci/Makefile_32 b/arch/x86/pci/Makefile_32
index 7fa519868d..89ec35d00e 100644
--- a/arch/x86/pci/Makefile_32
+++ b/arch/x86/pci/Makefile_32
@@ -6,11 +6,19 @@ obj-$(CONFIG_PCI_DIRECT)	+= direct.o
 obj-$(CONFIG_PCI_OLPC)		+= olpc.o
 
 pci-y				:= fixup.o
+
+# Do not change the ordering here. There is a nasty init function
+# ordering dependency which breaks when you move acpi.o below
+# legacy/irq.o
 pci-$(CONFIG_ACPI)		+= acpi.o
 pci-y				+= legacy.o irq.o
 
-pci-$(CONFIG_X86_VISWS)		+= visws.o fixup.o
-pci-$(CONFIG_X86_NUMAQ)		+= numa.o irq.o
+# Careful: VISWS and NUMAQ overrule the pci-y above. The colons are
+# therefor correct. This needs a proper fix by distangling the code.
+pci-$(CONFIG_X86_VISWS)		:= visws.o fixup.o
+pci-$(CONFIG_X86_NUMAQ)		:= numa.o irq.o
+
+# Necessary for NUMAQ as well
 pci-$(CONFIG_NUMA)		+= mp_bus_to_node.o
 
 obj-y				+= $(pci-y) common.o early.o