From: Auke Kok <auke-jan.h.kok@intel.com>
Date: Fri, 5 Oct 2007 22:22:02 +0000 (-0700)
Subject: e1000e: restore flow control settings properly
X-Git-Tag: v2.6.24-rc1~1454^2~86
X-Git-Url: https://err.no/cgi-bin/gitweb.cgi?a=commitdiff_plain;h=309af40b5f4c2065c9a5f74a360ad3d3b0c9c9cd;p=linux-2.6

e1000e: restore flow control settings properly

After a cable unplug the forced flow control settings were lost
accidentally and the flow control settings fell back to the default
EEPROM determined values. This breaks for people who want to
run without fc enabled - after a cable reset the driver would
refuse to run with fc disabled.

Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
---

diff --git a/drivers/net/e1000e/ethtool.c b/drivers/net/e1000e/ethtool.c
index 2e8218fb05..b7a7e2ae5e 100644
--- a/drivers/net/e1000e/ethtool.c
+++ b/drivers/net/e1000e/ethtool.c
@@ -301,6 +301,7 @@ static int e1000_set_pauseparam(struct net_device *netdev,
 	hw->mac.original_fc = hw->mac.fc;
 
 	if (adapter->fc_autoneg == AUTONEG_ENABLE) {
+		hw->mac.fc = e1000_fc_default;
 		if (netif_running(adapter->netdev)) {
 			e1000e_down(adapter);
 			e1000e_up(adapter);
diff --git a/drivers/net/e1000e/lib.c b/drivers/net/e1000e/lib.c
index 3bbfe605e1..0bdeca30c7 100644
--- a/drivers/net/e1000e/lib.c
+++ b/drivers/net/e1000e/lib.c
@@ -639,9 +639,15 @@ s32 e1000e_setup_link(struct e1000_hw *hw)
 	if (e1000_check_reset_block(hw))
 		return 0;
 
-	ret_val = e1000_set_default_fc_generic(hw);
-	if (ret_val)
-		return ret_val;
+	/*
+	 * If flow control is set to default, set flow control based on
+	 * the EEPROM flow control settings.
+	 */
+	if (mac->fc == e1000_fc_default) {
+		ret_val = e1000_set_default_fc_generic(hw);
+		if (ret_val)
+			return ret_val;
+	}
 
 	/* We want to save off the original Flow Control configuration just
 	 * in case we get disconnected and then reconnected into a different
diff --git a/drivers/net/e1000e/netdev.c b/drivers/net/e1000e/netdev.c
index 600538bc93..033e124d1c 100644
--- a/drivers/net/e1000e/netdev.c
+++ b/drivers/net/e1000e/netdev.c
@@ -4195,6 +4195,7 @@ static int __devinit e1000_probe(struct pci_dev *pdev,
 
 	/* Initialize link parameters. User can change them with ethtool */
 	adapter->hw.mac.autoneg = 1;
+	adapter->fc_autoneg = 1;
 	adapter->hw.mac.original_fc = e1000_fc_default;
 	adapter->hw.mac.fc = e1000_fc_default;
 	adapter->hw.phy.autoneg_advertised = 0x2f;