From: Alan Cox Date: Thu, 26 Apr 2007 07:19:25 +0000 (-0700) Subject: pata_hpt3x2n: Add HPT371N support and other bits X-Git-Tag: v2.6.22-rc1~1111^2~3 X-Git-Url: https://err.no/cgi-bin/gitweb.cgi?a=commitdiff_plain;h=28e21c8c0d44cd63bad4c62f94ef0c5a1cb8402c;p=linux-2.6 pata_hpt3x2n: Add HPT371N support and other bits Yes its no longer 3x2n but 3xxn, I can rename it if you want Jeff - Don't reset both ports each time (Sergei) - If we can't get a DPLL then abort entirely - Use ioport access for clock (from drivers/ide) - Add HPT371N support (from drivers/ide) Signed-off-by: Alan Cox Signed-off-by: Andrew Morton Signed-off-by: Jeff Garzik --- diff --git a/drivers/ata/pata_hpt3x2n.c b/drivers/ata/pata_hpt3x2n.c index 7832392314..6a34521b9e 100644 --- a/drivers/ata/pata_hpt3x2n.c +++ b/drivers/ata/pata_hpt3x2n.c @@ -8,10 +8,10 @@ * Copyright (C) 1999-2003 Andre Hedrick * Portions Copyright (C) 2001 Sun Microsystems, Inc. * Portions Copyright (C) 2003 Red Hat Inc + * Portions Copyright (C) 2005-2006 MontaVista Software, Inc. * * * TODO - * 371N * Work out best PLL policy */ @@ -142,6 +142,7 @@ static int hpt3x2n_cable_detect(struct ata_port *ap) /** * hpt3x2n_pre_reset - reset the hpt3x2n bus * @ap: ATA port to reset + * @deadline: deadline jiffies for the operation * * Perform the initial reset handling for the 3x2n series controllers. * Reset the hardware and state machine, @@ -151,8 +152,7 @@ static int hpt3xn_pre_reset(struct ata_port *ap) { struct pci_dev *pdev = to_pci_dev(ap->host->dev); /* Reset the state machine */ - pci_write_config_byte(pdev, 0x50, 0x37); - pci_write_config_byte(pdev, 0x54, 0x37); + pci_write_config_byte(pdev, 0x50 + 4 * ap->port_no, 0x37); udelay(100); return ata_std_prereset(ap); } @@ -433,8 +433,9 @@ static int hpt3x2n_pci_clock(struct pci_dev *pdev) { unsigned long freq; u32 fcnt; + unsigned long iobase = pci_resource_start(pdev, 4); - pci_read_config_dword(pdev, 0x70/*CHECKME*/, &fcnt); + fcnt = inl(iobase + 0x90); /* Not PCI readable for some chips */ if ((fcnt >> 12) != 0xABCDE) { printk(KERN_WARNING "hpt3xn: BIOS clock data not set.\n"); return 33; /* Not BIOS set */ @@ -503,6 +504,7 @@ static int hpt3x2n_init_one(struct pci_dev *dev, const struct pci_device_id *id) unsigned int pci_mhz; unsigned int f_low, f_high; int adjust; + unsigned long iobase = pci_resource_start(dev, 4); pci_read_config_dword(dev, PCI_CLASS_REVISION, &class_rev); class_rev &= 0xFF; @@ -512,6 +514,11 @@ static int hpt3x2n_init_one(struct pci_dev *dev, const struct pci_device_id *id) if (class_rev < 6) return -ENODEV; break; + case PCI_DEVICE_ID_TTI_HPT371: + if (class_rev < 2) + return -ENODEV; + /* 371N if rev > 1 */ + break; case PCI_DEVICE_ID_TTI_HPT372: /* 372N if rev >= 1*/ if (class_rev == 0) @@ -539,6 +546,19 @@ static int hpt3x2n_init_one(struct pci_dev *dev, const struct pci_device_id *id) irqmask &= ~0x10; pci_write_config_byte(dev, 0x5a, irqmask); + /* + * HPT371 chips physically have only one channel, the secondary one, + * but the primary channel registers do exist! Go figure... + * So, we manually disable the non-existing channel here + * (if the BIOS hasn't done this already). + */ + if (dev->device == PCI_DEVICE_ID_TTI_HPT371) { + u8 mcr1; + pci_read_config_byte(dev, 0x50, &mcr1); + mcr1 &= ~0x04; + pci_write_config_byte(dev, 0x50, mcr1); + } + /* Tune the PLL. HPT recommend using 75 for SATA, 66 for UDMA133 or 50 for UDMA100. Right now we always use 66 */ @@ -557,14 +577,24 @@ static int hpt3x2n_init_one(struct pci_dev *dev, const struct pci_device_id *id) break; pci_write_config_dword(dev, 0x5C, (f_high << 16) | f_low); } - if (adjust == 8) - printk(KERN_WARNING "hpt3xn: DPLL did not stabilize.\n"); + if (adjust == 8) { + printk(KERN_WARNING "hpt3x2n: DPLL did not stabilize.\n"); + return -ENODEV; + } /* Set our private data up. We only need a few flags so we use it directly */ port->private_data = NULL; - if (pci_mhz > 60) + if (pci_mhz > 60) { port->private_data = (void *)PCI66; + /* + * On HPT371N, if ATA clock is 66 MHz we must set bit 2 in + * the MISC. register to stretch the UltraDMA Tss timing. + * NOTE: This register is only writeable via I/O space. + */ + if (dev->device == PCI_DEVICE_ID_TTI_HPT371) + outb(inb(iobase + 0x9c) | 0x04, iobase + 0x9c); + } /* Now kick off ATA set up */ port_info[0] = port_info[1] = port; @@ -573,6 +603,7 @@ static int hpt3x2n_init_one(struct pci_dev *dev, const struct pci_device_id *id) static const struct pci_device_id hpt3x2n[] = { { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT366), }, + { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT371), }, { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT372), }, { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT302), }, { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT372N), },