From: Brice Goglin Date: Tue, 23 May 2006 10:10:15 +0000 (-0400) Subject: [PATCH] Add Myri-10G Ethernet driver X-Git-Tag: v2.6.18-rc1~1115^2~63 X-Git-Url: https://err.no/cgi-bin/gitweb.cgi?a=commitdiff_plain;h=0da34b6dfe55810ae60db57e08e2af8a808c0a55;p=linux-2.6 [PATCH] Add Myri-10G Ethernet driver Signed-off-by: Brice Goglin Signed-off-by: Andrew J. Gallatin drivers/net/Kconfig | 17 drivers/net/Makefile | 1 drivers/net/myri10ge/Makefile | 5 drivers/net/myri10ge/myri10ge.c | 2851 +++++++++++++++ drivers/net/myri10ge/myri10ge_mcp.h | 205 + drivers/net/myri10ge/myri10ge_mcp_gen_header.h | 58 include/linux/pci_ids.h | 1 7 files changed, 3138 insertions(+) Signed-off-by: Jeff Garzik --- diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig index 68bc073b8b..f499a3bc62 100644 --- a/drivers/net/Kconfig +++ b/drivers/net/Kconfig @@ -2327,6 +2327,23 @@ config S2IO_NAPI If in doubt, say N. +config MYRI10GE + tristate "Myricom Myri-10G Ethernet support" + depends on PCI + select FW_LOADER + select CRC32 + ---help--- + This driver supports Myricom Myri-10G Dual Protocol interface in + Ethernet mode. If the eeprom on your board is not recent enough, + you will need a newer firmware image. + You may get this image or more information, at: + + + + To compile this driver as a module, choose M here and read + . The module + will be called myri10ge. + endmenu source "drivers/net/tokenring/Kconfig" diff --git a/drivers/net/Makefile b/drivers/net/Makefile index b01cc9a3cb..1eced32875 100644 --- a/drivers/net/Makefile +++ b/drivers/net/Makefile @@ -192,6 +192,7 @@ obj-$(CONFIG_R8169) += r8169.o obj-$(CONFIG_AMD8111_ETH) += amd8111e.o obj-$(CONFIG_IBMVETH) += ibmveth.o obj-$(CONFIG_S2IO) += s2io.o +obj-$(CONFIG_MYRI10GE) += myri10ge/ obj-$(CONFIG_SMC91X) += smc91x.o obj-$(CONFIG_SMC911X) += smc911x.o obj-$(CONFIG_DM9000) += dm9000.o diff --git a/drivers/net/myri10ge/Makefile b/drivers/net/myri10ge/Makefile new file mode 100644 index 0000000000..5df891647a --- /dev/null +++ b/drivers/net/myri10ge/Makefile @@ -0,0 +1,5 @@ +# +# Makefile for the Myricom Myri-10G ethernet driver +# + +obj-$(CONFIG_MYRI10GE) += myri10ge.o diff --git a/drivers/net/myri10ge/myri10ge.c b/drivers/net/myri10ge/myri10ge.c new file mode 100644 index 0000000000..87933cba7e --- /dev/null +++ b/drivers/net/myri10ge/myri10ge.c @@ -0,0 +1,2851 @@ +/************************************************************************* + * myri10ge.c: Myricom Myri-10G Ethernet driver. + * + * Copyright (C) 2005, 2006 Myricom, Inc. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in the + * documentation and/or other materials provided with the distribution. + * 3. Neither the name of Myricom, Inc. nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND + * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + * ARE DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY + * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF + * SUCH DAMAGE. + * + * + * If the eeprom on your board is not recent enough, you will need to get a + * newer firmware image at: + * http://www.myri.com/scs/download-Myri10GE.html + * + * Contact Information: + * + * Myricom, Inc., 325N Santa Anita Avenue, Arcadia, CA 91006 + *************************************************************************/ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#ifdef CONFIG_MTRR +#include +#endif + +#include "myri10ge_mcp.h" +#include "myri10ge_mcp_gen_header.h" + +#define MYRI10GE_VERSION_STR "0.9.0" + +MODULE_DESCRIPTION("Myricom 10G driver (10GbE)"); +MODULE_AUTHOR("Maintainer: help@myri.com"); +MODULE_VERSION(MYRI10GE_VERSION_STR); +MODULE_LICENSE("Dual BSD/GPL"); + +#define MYRI10GE_MAX_ETHER_MTU 9014 + +#define MYRI10GE_ETH_STOPPED 0 +#define MYRI10GE_ETH_STOPPING 1 +#define MYRI10GE_ETH_STARTING 2 +#define MYRI10GE_ETH_RUNNING 3 +#define MYRI10GE_ETH_OPEN_FAILED 4 + +#define MYRI10GE_EEPROM_STRINGS_SIZE 256 +#define MYRI10GE_MAX_SEND_DESC_TSO ((65536 / 2048) * 2) + +#define MYRI10GE_NO_CONFIRM_DATA 0xffffffff +#define MYRI10GE_NO_RESPONSE_RESULT 0xffffffff + +struct myri10ge_rx_buffer_state { + struct sk_buff *skb; + DECLARE_PCI_UNMAP_ADDR(bus) + DECLARE_PCI_UNMAP_LEN(len) +}; + +struct myri10ge_tx_buffer_state { + struct sk_buff *skb; + int last; + DECLARE_PCI_UNMAP_ADDR(bus) + DECLARE_PCI_UNMAP_LEN(len) +}; + +struct myri10ge_cmd { + u32 data0; + u32 data1; + u32 data2; +}; + +struct myri10ge_rx_buf { + struct mcp_kreq_ether_recv __iomem *lanai; /* lanai ptr for recv ring */ + u8 __iomem *wc_fifo; /* w/c rx dma addr fifo address */ + struct mcp_kreq_ether_recv *shadow; /* host shadow of recv ring */ + struct myri10ge_rx_buffer_state *info; + int cnt; + int alloc_fail; + int mask; /* number of rx slots -1 */ +}; + +struct myri10ge_tx_buf { + struct mcp_kreq_ether_send __iomem *lanai; /* lanai ptr for sendq */ + u8 __iomem *wc_fifo; /* w/c send fifo address */ + struct mcp_kreq_ether_send *req_list; /* host shadow of sendq */ + char *req_bytes; + struct myri10ge_tx_buffer_state *info; + int mask; /* number of transmit slots -1 */ + int boundary; /* boundary transmits cannot cross */ + int req ____cacheline_aligned; /* transmit slots submitted */ + int pkt_start; /* packets started */ + int done ____cacheline_aligned; /* transmit slots completed */ + int pkt_done; /* packets completed */ +}; + +struct myri10ge_rx_done { + struct mcp_slot *entry; + dma_addr_t bus; + int cnt; + int idx; +}; + +struct myri10ge_priv { + int running; /* running? */ + int csum_flag; /* rx_csums? */ + struct myri10ge_tx_buf tx; /* transmit ring */ + struct myri10ge_rx_buf rx_small; + struct myri10ge_rx_buf rx_big; + struct myri10ge_rx_done rx_done; + int small_bytes; + struct net_device *dev; + struct net_device_stats stats; + u8 __iomem *sram; + int sram_size; + unsigned long board_span; + unsigned long iomem_base; + u32 __iomem *irq_claim; + u32 __iomem *irq_deassert; + char *mac_addr_string; + struct mcp_cmd_response *cmd; + dma_addr_t cmd_bus; + struct mcp_irq_data *fw_stats; + dma_addr_t fw_stats_bus; + struct pci_dev *pdev; + int msi_enabled; + unsigned int link_state; + unsigned int rdma_tags_available; + int intr_coal_delay; + u32 __iomem *intr_coal_delay_ptr; + int mtrr; + int wake_queue; + int stop_queue; + int down_cnt; + wait_queue_head_t down_wq; + struct work_struct watchdog_work; + struct timer_list watchdog_timer; + int watchdog_tx_done; + int watchdog_resets; + int tx_linearized; + int pause; + char *fw_name; + char eeprom_strings[MYRI10GE_EEPROM_STRINGS_SIZE]; + char fw_version[128]; + u8 mac_addr[6]; /* eeprom mac address */ + unsigned long serial_number; + int vendor_specific_offset; + u32 devctl; + u16 msi_flags; + u32 pm_state[16]; + u32 read_dma; + u32 write_dma; + u32 read_write_dma; +}; + +static char *myri10ge_fw_unaligned = "myri10ge_ethp_z8e.dat"; +static char *myri10ge_fw_aligned = "myri10ge_eth_z8e.dat"; + +static char *myri10ge_fw_name = NULL; +module_param(myri10ge_fw_name, charp, S_IRUGO | S_IWUSR); +MODULE_PARM_DESC(myri10ge_fw_name, "Firmware image name\n"); + +static int myri10ge_ecrc_enable = 1; +module_param(myri10ge_ecrc_enable, int, S_IRUGO); +MODULE_PARM_DESC(myri10ge_ecrc_enable, "Enable Extended CRC on PCI-E\n"); + +static int myri10ge_max_intr_slots = 1024; +module_param(myri10ge_max_intr_slots, int, S_IRUGO); +MODULE_PARM_DESC(myri10ge_max_intr_slots, "Interrupt queue slots\n"); + +static int myri10ge_small_bytes = -1; /* -1 == auto */ +module_param(myri10ge_small_bytes, int, S_IRUGO | S_IWUSR); +MODULE_PARM_DESC(myri10ge_small_bytes, "Threshold of small packets\n"); + +static int myri10ge_msi = 1; /* enable msi by default */ +module_param(myri10ge_msi, int, S_IRUGO); +MODULE_PARM_DESC(myri10ge_msi, "Enable Message Signalled Interrupts\n"); + +static int myri10ge_intr_coal_delay = 25; +module_param(myri10ge_intr_coal_delay, int, S_IRUGO); +MODULE_PARM_DESC(myri10ge_intr_coal_delay, "Interrupt coalescing delay\n"); + +static int myri10ge_flow_control = 1; +module_param(myri10ge_flow_control, int, S_IRUGO); +MODULE_PARM_DESC(myri10ge_flow_control, "Pause parameter\n"); + +static int myri10ge_deassert_wait = 1; +module_param(myri10ge_deassert_wait, int, S_IRUGO | S_IWUSR); +MODULE_PARM_DESC(myri10ge_deassert_wait, + "Wait when deasserting legacy interrupts\n"); + +static int myri10ge_force_firmware = 0; +module_param(myri10ge_force_firmware, int, S_IRUGO); +MODULE_PARM_DESC(myri10ge_force_firmware, + "Force firmware to assume aligned completions\n"); + +static int myri10ge_skb_cross_4k = 0; +module_param(myri10ge_skb_cross_4k, int, S_IRUGO | S_IWUSR); +MODULE_PARM_DESC(myri10ge_skb_cross_4k, + "Can a small skb cross a 4KB boundary?\n"); + +static int myri10ge_initial_mtu = MYRI10GE_MAX_ETHER_MTU - ETH_HLEN; +module_param(myri10ge_initial_mtu, int, S_IRUGO); +MODULE_PARM_DESC(myri10ge_initial_mtu, "Initial MTU\n"); + +static int myri10ge_napi_weight = 64; +module_param(myri10ge_napi_weight, int, S_IRUGO); +MODULE_PARM_DESC(myri10ge_napi_weight, "Set NAPI weight\n"); + +static int myri10ge_watchdog_timeout = 1; +module_param(myri10ge_watchdog_timeout, int, S_IRUGO); +MODULE_PARM_DESC(myri10ge_watchdog_timeout, "Set watchdog timeout\n"); + +static int myri10ge_max_irq_loops = 1048576; +module_param(myri10ge_max_irq_loops, int, S_IRUGO); +MODULE_PARM_DESC(myri10ge_max_irq_loops, + "Set stuck legacy IRQ detection threshold\n"); + +#define MYRI10GE_FW_OFFSET 1024*1024 +#define MYRI10GE_HIGHPART_TO_U32(X) \ +(sizeof (X) == 8) ? ((u32)((u64)(X) >> 32)) : (0) +#define MYRI10GE_LOWPART_TO_U32(X) ((u32)(X)) + +#define myri10ge_pio_copy(to,from,size) __iowrite64_copy(to,from,size/8) + +static int +myri10ge_send_cmd(struct myri10ge_priv *mgp, u32 cmd, + struct myri10ge_cmd *data, int atomic) +{ + struct mcp_cmd *buf; + char buf_bytes[sizeof(*buf) + 8]; + struct mcp_cmd_response *response = mgp->cmd; + char __iomem *cmd_addr = mgp->sram + MXGEFW_CMD_OFFSET; + u32 dma_low, dma_high, result, value; + int sleep_total = 0; + + /* ensure buf is aligned to 8 bytes */ + buf = (struct mcp_cmd *)ALIGN((unsigned long)buf_bytes, 8); + + buf->data0 = htonl(data->data0); + buf->data1 = htonl(data->data1); + buf->data2 = htonl(data->data2); + buf->cmd = htonl(cmd); + dma_low = MYRI10GE_LOWPART_TO_U32(mgp->cmd_bus); + dma_high = MYRI10GE_HIGHPART_TO_U32(mgp->cmd_bus); + + buf->response_addr.low = htonl(dma_low); + buf->response_addr.high = htonl(dma_high); + response->result = MYRI10GE_NO_RESPONSE_RESULT; + mb(); + myri10ge_pio_copy(cmd_addr, buf, sizeof(*buf)); + + /* wait up to 15ms. Longest command is the DMA benchmark, + * which is capped at 5ms, but runs from a timeout handler + * that runs every 7.8ms. So a 15ms timeout leaves us with + * a 2.2ms margin + */ + if (atomic) { + /* if atomic is set, do not sleep, + * and try to get the completion quickly + * (1ms will be enough for those commands) */ + for (sleep_total = 0; + sleep_total < 1000 + && response->result == MYRI10GE_NO_RESPONSE_RESULT; + sleep_total += 10) + udelay(10); + } else { + /* use msleep for most command */ + for (sleep_total = 0; + sleep_total < 15 + && response->result == MYRI10GE_NO_RESPONSE_RESULT; + sleep_total++) + msleep(1); + } + + result = ntohl(response->result); + value = ntohl(response->data); + if (result != MYRI10GE_NO_RESPONSE_RESULT) { + if (result == 0) { + data->data0 = value; + return 0; + } else { + dev_err(&mgp->pdev->dev, + "command %d failed, result = %d\n", + cmd, result); + return -ENXIO; + } + } + + dev_err(&mgp->pdev->dev, "command %d timed out, result = %d\n", + cmd, result); + return -EAGAIN; +} + +/* + * The eeprom strings on the lanaiX have the format + * SN=x\0 + * MAC=x:x:x:x:x:x\0 + * PT:ddd mmm xx xx:xx:xx xx\0 + * PV:ddd mmm xx xx:xx:xx xx\0 + */ +static int myri10ge_read_mac_addr(struct myri10ge_priv *mgp) +{ + char *ptr, *limit; + int i; + + ptr = mgp->eeprom_strings; + limit = mgp->eeprom_strings + MYRI10GE_EEPROM_STRINGS_SIZE; + + while (*ptr != '\0' && ptr < limit) { + if (memcmp(ptr, "MAC=", 4) == 0) { + ptr += 4; + mgp->mac_addr_string = ptr; + for (i = 0; i < 6; i++) { + if ((ptr + 2) > limit) + goto abort; + mgp->mac_addr[i] = + simple_strtoul(ptr, &ptr, 16); + ptr += 1; + } + } + if (memcmp((const void *)ptr, "SN=", 3) == 0) { + ptr += 3; + mgp->serial_number = simple_strtoul(ptr, &ptr, 10); + } + while (ptr < limit && *ptr++) ; + } + + return 0; + +abort: + dev_err(&mgp->pdev->dev, "failed to parse eeprom_strings\n"); + return -ENXIO; +} + +/* + * Enable or disable periodic RDMAs from the host to make certain + * chipsets resend dropped PCIe messages + */ + +static void myri10ge_dummy_rdma(struct myri10ge_priv *mgp, int enable) +{ + char __iomem *submit; + u32 buf[16]; + u32 dma_low, dma_high; + int i; + + /* clear confirmation addr */ + mgp->cmd->data = 0; + mb(); + + /* send a rdma command to the PCIe engine, and wait for the + * response in the confirmation address. The firmware should + * write a -1 there to indicate it is alive and well + */ + dma_low = MYRI10GE_LOWPART_TO_U32(mgp->cmd_bus); + dma_high = MYRI10GE_HIGHPART_TO_U32(mgp->cmd_bus); + + buf[0] = htonl(dma_high); /* confirm addr MSW */ + buf[1] = htonl(dma_low); /* confirm addr LSW */ + buf[2] = htonl(MYRI10GE_NO_CONFIRM_DATA); /* confirm data */ + buf[3] = htonl(dma_high); /* dummy addr MSW */ + buf[4] = htonl(dma_low); /* dummy addr LSW */ + buf[5] = htonl(enable); /* enable? */ + + submit = mgp->sram + 0xfc01c0; + + myri10ge_pio_copy(submit, &buf, sizeof(buf)); + for (i = 0; mgp->cmd->data != MYRI10GE_NO_CONFIRM_DATA && i < 20; i++) + msleep(1); + if (mgp->cmd->data != MYRI10GE_NO_CONFIRM_DATA) + dev_err(&mgp->pdev->dev, "dummy rdma %s failed\n", + (enable ? "enable" : "disable")); +} + +static int +myri10ge_validate_firmware(struct myri10ge_priv *mgp, + struct mcp_gen_header *hdr) +{ + struct device *dev = &mgp->pdev->dev; + int major, minor; + + /* check firmware type */ + if (ntohl(hdr->mcp_type) != MCP_TYPE_ETH) { + dev_err(dev, "Bad firmware type: 0x%x\n", ntohl(hdr->mcp_type)); + return -EINVAL; + } + + /* save firmware version for ethtool */ + strncpy(mgp->fw_version, hdr->version, sizeof(mgp->fw_version)); + + sscanf(mgp->fw_version, "%d.%d", &major, &minor); + + if (!(major == MXGEFW_VERSION_MAJOR && minor == MXGEFW_VERSION_MINOR)) { + dev_err(dev, "Found firmware version %s\n", mgp->fw_version); + dev_err(dev, "Driver needs %d.%d\n", MXGEFW_VERSION_MAJOR, + MXGEFW_VERSION_MINOR); + return -EINVAL; + } + return 0; +} + +static int myri10ge_load_hotplug_firmware(struct myri10ge_priv *mgp, u32 * size) +{ + unsigned crc, reread_crc; + const struct firmware *fw; + struct device *dev = &mgp->pdev->dev; + struct mcp_gen_header *hdr; + size_t hdr_offset; + int status; + + if ((status = request_firmware(&fw, mgp->fw_name, dev)) < 0) { + dev_err(dev, "Unable to load %s firmware image via hotplug\n", + mgp->fw_name); + status = -EINVAL; + goto abort_with_nothing; + } + + /* check size */ + + if (fw->size >= mgp->sram_size - MYRI10GE_FW_OFFSET || + fw->size < MCP_HEADER_PTR_OFFSET + 4) { + dev_err(dev, "Firmware size invalid:%d\n", (int)fw->size); + status = -EINVAL; + goto abort_with_fw; + } + + /* check id */ + hdr_offset = ntohl(*(u32 *) (fw->data + MCP_HEADER_PTR_OFFSET)); + if ((hdr_offset & 3) || hdr_offset + sizeof(*hdr) > fw->size) { + dev_err(dev, "Bad firmware file\n"); + status = -EINVAL; + goto abort_with_fw; + } + hdr = (void *)(fw->data + hdr_offset); + + status = myri10ge_validate_firmware(mgp, hdr); + if (status != 0) + goto abort_with_fw; + + crc = crc32(~0, fw->data, fw->size); + memcpy_toio(mgp->sram + MYRI10GE_FW_OFFSET, fw->data, fw->size); + /* corruption checking is good for parity recovery and buggy chipset */ + memcpy_fromio(fw->data, mgp->sram + MYRI10GE_FW_OFFSET, fw->size); + reread_crc = crc32(~0, fw->data, fw->size); + if (crc != reread_crc) { + dev_err(dev, "CRC failed(fw-len=%u), got 0x%x (expect 0x%x)\n", + (unsigned)fw->size, reread_crc, crc); + status = -EIO; + goto abort_with_fw; + } + *size = (u32) fw->size; + +abort_with_fw: + release_firmware(fw); + +abort_with_nothing: + return status; +} + +static int myri10ge_adopt_running_firmware(struct myri10ge_priv *mgp) +{ + struct mcp_gen_header *hdr; + struct device *dev = &mgp->pdev->dev; + const size_t bytes = sizeof(struct mcp_gen_header); + size_t hdr_offset; + int status; + + /* find running firmware header */ + hdr_offset = ntohl(__raw_readl(mgp->sram + MCP_HEADER_PTR_OFFSET)); + + if ((hdr_offset & 3) || hdr_offset + sizeof(*hdr) > mgp->sram_size) { + dev_err(dev, "Running firmware has bad header offset (%d)\n", + (int)hdr_offset); + return -EIO; + } + + /* copy header of running firmware from SRAM to host memory to + * validate firmware */ + hdr = kmalloc(bytes, GFP_KERNEL); + if (hdr == NULL) { + dev_err(dev, "could not malloc firmware hdr\n"); + return -ENOMEM; + } + memcpy_fromio(hdr, mgp->sram + hdr_offset, bytes); + status = myri10ge_validate_firmware(mgp, hdr); + kfree(hdr); + return status; +} + +static int myri10ge_load_firmware(struct myri10ge_priv *mgp) +{ + char __iomem *submit; + u32 buf[16]; + u32 dma_low, dma_high, size; + int status, i; + + status = myri10ge_load_hotplug_firmware(mgp, &size); + if (status) { + dev_warn(&mgp->pdev->dev, "hotplug firmware loading failed\n"); + + /* Do not attempt to adopt firmware if there + * was a bad crc */ + if (status == -EIO) + return status; + + status = myri10ge_adopt_running_firmware(mgp); + if (status != 0) { + dev_err(&mgp->pdev->dev, + "failed to adopt running firmware\n"); + return status; + } + dev_info(&mgp->pdev->dev, + "Successfully adopted running firmware\n"); + if (mgp->tx.boundary == 4096) { + dev_warn(&mgp->pdev->dev, + "Using firmware currently running on NIC" + ". For optimal\n"); + dev_warn(&mgp->pdev->dev, + "performance consider loading optimized " + "firmware\n"); + dev_warn(&mgp->pdev->dev, "via hotplug\n"); + } + + mgp->fw_name = "adopted"; + mgp->tx.boundary = 2048; + return status; + } + + /* clear confirmation addr */ + mgp->cmd->data = 0; + mb(); + + /* send a reload command to the bootstrap MCP, and wait for the + * response in the confirmation address. The firmware should + * write a -1 there to indicate it is alive and well + */ + dma_low = MYRI10GE_LOWPART_TO_U32(mgp->cmd_bus); + dma_high = MYRI10GE_HIGHPART_TO_U32(mgp->cmd_bus); + + buf[0] = htonl(dma_high); /* confirm addr MSW */ + buf[1] = htonl(dma_low); /* confirm addr LSW */ + buf[2] = htonl(MYRI10GE_NO_CONFIRM_DATA); /* confirm data */ + + /* FIX: All newest firmware should un-protect the bottom of + * the sram before handoff. However, the very first interfaces + * do not. Therefore the handoff copy must skip the first 8 bytes + */ + buf[3] = htonl(MYRI10GE_FW_OFFSET + 8); /* where the code starts */ + buf[4] = htonl(size - 8); /* length of code */ + buf[5] = htonl(8); /* where to copy to */ + buf[6] = htonl(0); /* where to jump to */ + + submit = mgp->sram + 0xfc0000; + + myri10ge_pio_copy(submit, &buf, sizeof(buf)); + mb(); + msleep(1); + mb(); + i = 0; + while (mgp->cmd->data != MYRI10GE_NO_CONFIRM_DATA && i < 20) { + msleep(1); + i++; + } + if (mgp->cmd->data != MYRI10GE_NO_CONFIRM_DATA) { + dev_err(&mgp->pdev->dev, "handoff failed\n"); + return -ENXIO; + } + dev_info(&mgp->pdev->dev, "handoff confirmed\n"); + myri10ge_dummy_rdma(mgp, mgp->tx.boundary != 4096); + + return 0; +} + +static int myri10ge_update_mac_address(struct myri10ge_priv *mgp, u8 * addr) +{ + struct myri10ge_cmd cmd; + int status; + + cmd.data0 = ((addr[0] << 24) | (addr[1] << 16) + | (addr[2] << 8) | addr[3]); + + cmd.data1 = ((addr[4] << 8) | (addr[5])); + + status = myri10ge_send_cmd(mgp, MXGEFW_SET_MAC_ADDRESS, &cmd, 0); + return status; +} + +static int myri10ge_change_pause(struct myri10ge_priv *mgp, int pause) +{ + struct myri10ge_cmd cmd; + int status, ctl; + + ctl = pause ? MXGEFW_ENABLE_FLOW_CONTROL : MXGEFW_DISABLE_FLOW_CONTROL; + status = myri10ge_send_cmd(mgp, ctl, &cmd, 0); + + if (status) { + printk(KERN_ERR + "myri10ge: %s: Failed to set flow control mode\n", + mgp->dev->name); + return status; + } + mgp->pause = pause; + return 0; +} + +static void +myri10ge_change_promisc(struct myri10ge_priv *mgp, int promisc, int atomic) +{ + struct myri10ge_cmd cmd; + int status, ctl; + + ctl = promisc ? MXGEFW_ENABLE_PROMISC : MXGEFW_DISABLE_PROMISC; + status = myri10ge_send_cmd(mgp, ctl, &cmd, atomic); + if (status) + printk(KERN_ERR "myri10ge: %s: Failed to set promisc mode\n", + mgp->dev->name); +} + +static int myri10ge_reset(struct myri10ge_priv *mgp) +{ + struct myri10ge_cmd cmd; + int status; + size_t bytes; + u32 len; + + /* try to send a reset command to the card to see if it + * is alive */ + memset(&cmd, 0, sizeof(cmd)); + status = myri10ge_send_cmd(mgp, MXGEFW_CMD_RESET, &cmd, 0); + if (status != 0) { + dev_err(&mgp->pdev->dev, "failed reset\n"); + return -ENXIO; + } + + /* Now exchange information about interrupts */ + + bytes = myri10ge_max_intr_slots * sizeof(*mgp->rx_done.entry); + memset(mgp->rx_done.entry, 0, bytes); + cmd.data0 = (u32) bytes; + status = myri10ge_send_cmd(mgp, MXGEFW_CMD_SET_INTRQ_SIZE, &cmd, 0); + cmd.data0 = MYRI10GE_LOWPART_TO_U32(mgp->rx_done.bus); + cmd.data1 = MYRI10GE_HIGHPART_TO_U32(mgp->rx_done.bus); + status |= myri10ge_send_cmd(mgp, MXGEFW_CMD_SET_INTRQ_DMA, &cmd, 0); + + status |= + myri10ge_send_cmd(mgp, MXGEFW_CMD_GET_IRQ_ACK_OFFSET, &cmd, 0); + mgp->irq_claim = (__iomem u32 *) (mgp->sram + cmd.data0); + if (!mgp->msi_enabled) { + status |= myri10ge_send_cmd + (mgp, MXGEFW_CMD_GET_IRQ_DEASSERT_OFFSET, &cmd, 0); + mgp->irq_deassert = (__iomem u32 *) (mgp->sram + cmd.data0); + + } + status |= myri10ge_send_cmd + (mgp, MXGEFW_CMD_GET_INTR_COAL_DELAY_OFFSET, &cmd, 0); + mgp->intr_coal_delay_ptr = (__iomem u32 *) (mgp->sram + cmd.data0); + if (status != 0) { + dev_err(&mgp->pdev->dev, "failed set interrupt parameters\n"); + return status; + } + __raw_writel(htonl(mgp->intr_coal_delay), mgp->intr_coal_delay_ptr); + + /* Run a small DMA test. + * The magic multipliers to the length tell the firmware + * to do DMA read, write, or read+write tests. The + * results are returned in cmd.data0. The upper 16 + * bits or the return is the number of transfers completed. + * The lower 16 bits is the time in 0.5us ticks that the + * transfers took to complete. + */ + + len = mgp->tx.boundary; + + cmd.data0 = MYRI10GE_LOWPART_TO_U32(mgp->rx_done.bus); + cmd.data1 = MYRI10GE_HIGHPART_TO_U32(mgp->rx_done.bus); + cmd.data2 = len * 0x10000; + status = myri10ge_send_cmd(mgp, MXGEFW_DMA_TEST, &cmd, 0); + if (status == 0) + mgp->read_dma = ((cmd.data0 >> 16) * len * 2) / + (cmd.data0 & 0xffff); + else + dev_warn(&mgp->pdev->dev, "DMA read benchmark failed: %d\n", + status); + cmd.data0 = MYRI10GE_LOWPART_TO_U32(mgp->rx_done.bus); + cmd.data1 = MYRI10GE_HIGHPART_TO_U32(mgp->rx_done.bus); + cmd.data2 = len * 0x1; + status = myri10ge_send_cmd(mgp, MXGEFW_DMA_TEST, &cmd, 0); + if (status == 0) + mgp->write_dma = ((cmd.data0 >> 16) * len * 2) / + (cmd.data0 & 0xffff); + else + dev_warn(&mgp->pdev->dev, "DMA write benchmark failed: %d\n", + status); + + cmd.data0 = MYRI10GE_LOWPART_TO_U32(mgp->rx_done.bus); + cmd.data1 = MYRI10GE_HIGHPART_TO_U32(mgp->rx_done.bus); + cmd.data2 = len * 0x10001; + status = myri10ge_send_cmd(mgp, MXGEFW_DMA_TEST, &cmd, 0); + if (status == 0) + mgp->read_write_dma = ((cmd.data0 >> 16) * len * 2 * 2) / + (cmd.data0 & 0xffff); + else + dev_warn(&mgp->pdev->dev, + "DMA read/write benchmark failed: %d\n", status); + + memset(mgp->rx_done.entry, 0, bytes); + + /* reset mcp/driver shared state back to 0 */ + mgp->tx.req = 0; + mgp->tx.done = 0; + mgp->tx.pkt_start = 0; + mgp->tx.pkt_done = 0; + mgp->rx_big.cnt = 0; + mgp->rx_small.cnt = 0; + mgp->rx_done.idx = 0; + mgp->rx_done.cnt = 0; + status = myri10ge_update_mac_address(mgp, mgp->dev->dev_addr); + myri10ge_change_promisc(mgp, 0, 0); + myri10ge_change_pause(mgp, mgp->pause); + return status; +} + +static inline void +myri10ge_submit_8rx(struct mcp_kreq_ether_recv __iomem * dst, + struct mcp_kreq_ether_recv *src) +{ + u32 low; + + low = src->addr_low; + src->addr_low = DMA_32BIT_MASK; + myri10ge_pio_copy(dst, src, 8 * sizeof(*src)); + mb(); + src->addr_low = low; + __raw_writel(low, &dst->addr_low); + mb(); +} + +/* + * Set of routunes to get a new receive buffer. Any buffer which + * crosses a 4KB boundary must start on a 4KB boundary due to PCIe + * wdma restrictions. We also try to align any smaller allocation to + * at least a 16 byte boundary for efficiency. We assume the linux + * memory allocator works by powers of 2, and will not return memory + * smaller than 2KB which crosses a 4KB boundary. If it does, we fall + * back to allocating 2x as much space as required. + * + * We intend to replace large (>4KB) skb allocations by using + * pages directly and building a fraglist in the near future. + */ + +static inline struct sk_buff *myri10ge_alloc_big(int bytes) +{ + struct sk_buff *skb; + unsigned long data, roundup; + + skb = dev_alloc_skb(bytes + 4096 + MXGEFW_PAD); + if (skb == NULL) + return NULL; + + /* Correct skb->truesize so that socket buffer + * accounting is not confused the rounding we must + * do to satisfy alignment constraints. + */ + skb->truesize -= 4096; + + data = (unsigned long)(skb->data); + roundup = (-data) & (4095); + skb_reserve(skb, roundup); + return skb; +} + +/* Allocate 2x as much space as required and use whichever portion + * does not cross a 4KB boundary */ +static inline struct sk_buff *myri10ge_alloc_small_safe(unsigned int bytes) +{ + struct sk_buff *skb; + unsigned long data, boundary; + + skb = dev_alloc_skb(2 * (bytes + MXGEFW_PAD) - 1); + if (unlikely(skb == NULL)) + return NULL; + + /* Correct skb->truesize so that socket buffer + * accounting is not confused the rounding we must + * do to satisfy alignment constraints. + */ + skb->truesize -= bytes + MXGEFW_PAD; + + data = (unsigned long)(skb->data); + boundary = (data + 4095UL) & ~4095UL; + if ((boundary - data) >= (bytes + MXGEFW_PAD)) + return skb; + + skb_reserve(skb, boundary - data); + return skb; +} + +/* Allocate just enough space, and verify that the allocated + * space does not cross a 4KB boundary */ +static inline struct sk_buff *myri10ge_alloc_small(int bytes) +{ + struct sk_buff *skb; + unsigned long roundup, data, end; + + skb = dev_alloc_skb(bytes + 16 + MXGEFW_PAD); + if (unlikely(skb == NULL)) + return NULL; + + /* Round allocated buffer to 16 byte boundary */ + data = (unsigned long)(skb->data); + roundup = (-data) & 15UL; + skb_reserve(skb, roundup); + /* Verify that the data buffer does not cross a page boundary */ + data = (unsigned long)(skb->data); + end = data + bytes + MXGEFW_PAD - 1; + if (unlikely(((end >> 12) != (data >> 12)) && (data & 4095UL))) { + printk(KERN_NOTICE + "myri10ge_alloc_small: small skb crossed 4KB boundary\n"); + myri10ge_skb_cross_4k = 1; + dev_kfree_skb_any(skb); + skb = myri10ge_alloc_small_safe(bytes); + } + return skb; +} + +static inline int +myri10ge_getbuf(struct myri10ge_rx_buf *rx, struct pci_dev *pdev, int bytes, + int idx) +{ + struct sk_buff *skb; + dma_addr_t bus; + int len, retval = 0; + + bytes += VLAN_HLEN; /* account for 802.1q vlan tag */ + + if ((bytes + MXGEFW_PAD) > (4096 - 16) /* linux overhead */ ) + skb = myri10ge_alloc_big(bytes); + else if (myri10ge_skb_cross_4k) + skb = myri10ge_alloc_small_safe(bytes); + else + skb = myri10ge_alloc_small(bytes); + + if (unlikely(skb == NULL)) { + rx->alloc_fail++; + retval = -ENOBUFS; + goto done; + } + + /* set len so that it only covers the area we + * need mapped for DMA */ + len = bytes + MXGEFW_PAD; + + bus = pci_map_single(pdev, skb->data, len, PCI_DMA_FROMDEVICE); + rx->info[idx].skb = skb; + pci_unmap_addr_set(&rx->info[idx], bus, bus); + pci_unmap_len_set(&rx->info[idx], len, len); + rx->shadow[idx].addr_low = htonl(MYRI10GE_LOWPART_TO_U32(bus)); + rx->shadow[idx].addr_high = htonl(MYRI10GE_HIGHPART_TO_U32(bus)); + +done: + /* copy 8 descriptors (64-bytes) to the mcp at a time */ + if ((idx & 7) == 7) { + if (rx->wc_fifo == NULL) + myri10ge_submit_8rx(&rx->lanai[idx - 7], + &rx->shadow[idx - 7]); + else { + mb(); + myri10ge_pio_copy(rx->wc_fifo, + &rx->shadow[idx - 7], 64); + } + } + return retval; +} + +static inline void myri10ge_vlan_ip_csum(struct sk_buff *skb, u16 hw_csum) +{ + struct vlan_hdr *vh = (struct vlan_hdr *)(skb->data); + + if ((skb->protocol == ntohs(ETH_P_8021Q)) && + (vh->h_vlan_encapsulated_proto == htons(ETH_P_IP) || + vh->h_vlan_encapsulated_proto == htons(ETH_P_IPV6))) { + skb->csum = hw_csum; + skb->ip_summed = CHECKSUM_HW; + } +} + +static inline unsigned long +myri10ge_rx_done(struct myri10ge_priv *mgp, struct myri10ge_rx_buf *rx, + int bytes, int len, int csum) +{ + dma_addr_t bus; + struct sk_buff *skb; + int idx, unmap_len; + + idx = rx->cnt & rx->mask; + rx->cnt++; + + /* save a pointer to the received skb */ + skb = rx->info[idx].skb; + bus = pci_unmap_addr(&rx->info[idx], bus); + unmap_len = pci_unmap_len(&rx->info[idx], len); + + /* try to replace the received skb */ + if (myri10ge_getbuf(rx, mgp->pdev, bytes, idx)) { + /* drop the frame -- the old skbuf is re-cycled */ + mgp->stats.rx_dropped += 1; + return 0; + } + + /* unmap the recvd skb */ + pci_unmap_single(mgp->pdev, bus, unmap_len, PCI_DMA_FROMDEVICE); + + /* mcp implicitly skips 1st bytes so that packet is properly + * aligned */ + skb_reserve(skb, MXGEFW_PAD); + + /* set the length of the frame */ + skb_put(skb, len); + + skb->protocol = eth_type_trans(skb, mgp->dev); + skb->dev = mgp->dev; + if (mgp->csum_flag) { + if ((skb->protocol == ntohs(ETH_P_IP)) || + (skb->protocol == ntohs(ETH_P_IPV6))) { + skb->csum = ntohs((u16) csum); + skb->ip_summed = CHECKSUM_HW; + } else + myri10ge_vlan_ip_csum(skb, ntohs((u16) csum)); + } + + netif_receive_skb(skb); + mgp->dev->last_rx = jiffies; + return 1; +} + +static inline void myri10ge_tx_done(struct myri10ge_priv *mgp, int mcp_index) +{ + struct pci_dev *pdev = mgp->pdev; + struct myri10ge_tx_buf *tx = &mgp->tx; + struct sk_buff *skb; + int idx, len; + int limit = 0; + + while (tx->pkt_done != mcp_index) { + idx = tx->done & tx->mask; + skb = tx->info[idx].skb; + + /* Mark as free */ + tx->info[idx].skb = NULL; + if (tx->info[idx].last) { + tx->pkt_done++; + tx->info[idx].last = 0; + } + tx->done++; + len = pci_unmap_len(&tx->info[idx], len); + pci_unmap_len_set(&tx->info[idx], len, 0); + if (skb) { + mgp->stats.tx_bytes += skb->len; + mgp->stats.tx_packets++; + dev_kfree_skb_irq(skb); + if (len) + pci_unmap_single(pdev, + pci_unmap_addr(&tx->info[idx], + bus), len, + PCI_DMA_TODEVICE); + } else { + if (len) + pci_unmap_page(pdev, + pci_unmap_addr(&tx->info[idx], + bus), len, + PCI_DMA_TODEVICE); + } + + /* limit potential for livelock by only handling + * 2 full tx rings per call */ + if (unlikely(++limit > 2 * tx->mask)) + break; + } + /* start the queue if we've stopped it */ + if (netif_queue_stopped(mgp->dev) + && tx->req - tx->done < (tx->mask >> 1)) { + mgp->wake_queue++; + netif_wake_queue(mgp->dev); + } +} + +static inline void myri10ge_clean_rx_done(struct myri10ge_priv *mgp, int *limit) +{ + struct myri10ge_rx_done *rx_done = &mgp->rx_done; + unsigned long rx_bytes = 0; + unsigned long rx_packets = 0; + unsigned long rx_ok; + + int idx = rx_done->idx; + int cnt = rx_done->cnt; + u16 length; + u16 checksum; + + while (rx_done->entry[idx].length != 0 && *limit != 0) { + length = ntohs(rx_done->entry[idx].length); + rx_done->entry[idx].length = 0; + checksum = ntohs(rx_done->entry[idx].checksum); + if (length <= mgp->small_bytes) + rx_ok = myri10ge_rx_done(mgp, &mgp->rx_small, + mgp->small_bytes, + length, checksum); + else + rx_ok = myri10ge_rx_done(mgp, &mgp->rx_big, + mgp->dev->mtu + ETH_HLEN, + length, checksum); + rx_packets += rx_ok; + rx_bytes += rx_ok * (unsigned long)length; + cnt++; + idx = cnt & (myri10ge_max_intr_slots - 1); + + /* limit potential for livelock by only handling a + * limited number of frames. */ + (*limit)--; + } + rx_done->idx = idx; + rx_done->cnt = cnt; + mgp->stats.rx_packets += rx_packets; + mgp->stats.rx_bytes += rx_bytes; +} + +static inline void myri10ge_check_statblock(struct myri10ge_priv *mgp) +{ + struct mcp_irq_data *stats = mgp->fw_stats; + + if (unlikely(stats->stats_updated)) { + if (mgp->link_state != stats->link_up) { + mgp->link_state = stats->link_up; + if (mgp->link_state) { + printk(KERN_INFO "myri10ge: %s: link up\n", + mgp->dev->name); + netif_carrier_on(mgp->dev); + } else { + printk(KERN_INFO "myri10ge: %s: link down\n", + mgp->dev->name); + netif_carrier_off(mgp->dev); + } + } + if (mgp->rdma_tags_available != + ntohl(mgp->fw_stats->rdma_tags_available)) { + mgp->rdma_tags_available = + ntohl(mgp->fw_stats->rdma_tags_available); + printk(KERN_WARNING "myri10ge: %s: RDMA timed out! " + "%d tags left\n", mgp->dev->name, + mgp->rdma_tags_available); + } + mgp->down_cnt += stats->link_down; + if (stats->link_down) + wake_up(&mgp->down_wq); + } +} + +static int myri10ge_poll(struct net_device *netdev, int *budget) +{ + struct myri10ge_priv *mgp = netdev_priv(netdev); + struct myri10ge_rx_done *rx_done = &mgp->rx_done; + int limit, orig_limit, work_done; + + /* process as many rx events as NAPI will allow */ + limit = min(*budget, netdev->quota); + orig_limit = limit; + myri10ge_clean_rx_done(mgp, &limit); + work_done = orig_limit - limit; + *budget -= work_done; + netdev->quota -= work_done; + + if (rx_done->entry[rx_done->idx].length == 0 || !netif_running(netdev)) { + netif_rx_complete(netdev); + __raw_writel(htonl(3), mgp->irq_claim); + return 0; + } + return 1; +} + +static irqreturn_t myri10ge_intr(int irq, void *arg, struct pt_regs *regs) +{ + struct myri10ge_priv *mgp = arg; + struct mcp_irq_data *stats = mgp->fw_stats; + struct myri10ge_tx_buf *tx = &mgp->tx; + u32 send_done_count; + int i; + + /* make sure it is our IRQ, and that the DMA has finished */ + if (unlikely(!stats->valid)) + return (IRQ_NONE); + + /* low bit indicates receives are present, so schedule + * napi poll handler */ + if (stats->valid & 1) + netif_rx_schedule(mgp->dev); + + if (!mgp->msi_enabled) { + __raw_writel(0, mgp->irq_deassert); + if (!myri10ge_deassert_wait) + stats->valid = 0; + mb(); + } else + stats->valid = 0; + + /* Wait for IRQ line to go low, if using INTx */ + i = 0; + while (1) { + i++; + /* check for transmit completes and receives */ + send_done_count = ntohl(stats->send_done_count); + if (send_done_count != tx->pkt_done) + myri10ge_tx_done(mgp, (int)send_done_count); + if (unlikely(i > myri10ge_max_irq_loops)) { + printk(KERN_WARNING "myri10ge: %s: irq stuck?\n", + mgp->dev->name); + stats->valid = 0; + schedule_work(&mgp->watchdog_work); + } + if (likely(stats->valid == 0)) + break; + cpu_relax(); + barrier(); + } + + myri10ge_check_statblock(mgp); + + __raw_writel(htonl(3), mgp->irq_claim + 1); + return (IRQ_HANDLED); +} + +static int +myri10ge_get_settings(struct net_device *netdev, struct ethtool_cmd *cmd) +{ + cmd->autoneg = AUTONEG_DISABLE; + cmd->speed = SPEED_10000; + cmd->duplex = DUPLEX_FULL; + return 0; +} + +static void +myri10ge_get_drvinfo(struct net_device *netdev, struct ethtool_drvinfo *info) +{ + struct myri10ge_priv *mgp = netdev_priv(netdev); + + strlcpy(info->driver, "myri10ge", sizeof(info->driver)); + strlcpy(info->version, MYRI10GE_VERSION_STR, sizeof(info->version)); + strlcpy(info->fw_version, mgp->fw_version, sizeof(info->fw_version)); + strlcpy(info->bus_info, pci_name(mgp->pdev), sizeof(info->bus_info)); +} + +static int +myri10ge_get_coalesce(struct net_device *netdev, struct ethtool_coalesce *coal) +{ + struct myri10ge_priv *mgp = netdev_priv(netdev); + coal->rx_coalesce_usecs = mgp->intr_coal_delay; + return 0; +} + +static int +myri10ge_set_coalesce(struct net_device *netdev, struct ethtool_coalesce *coal) +{ + struct myri10ge_priv *mgp = netdev_priv(netdev); + + mgp->intr_coal_delay = coal->rx_coalesce_usecs; + __raw_writel(htonl(mgp->intr_coal_delay), mgp->intr_coal_delay_ptr); + return 0; +} + +static void +myri10ge_get_pauseparam(struct net_device *netdev, + struct ethtool_pauseparam *pause) +{ + struct myri10ge_priv *mgp = netdev_priv(netdev); + + pause->autoneg = 0; + pause->rx_pause = mgp->pause; + pause->tx_pause = mgp->pause; +} + +static int +myri10ge_set_pauseparam(struct net_device *netdev, + struct ethtool_pauseparam *pause) +{ + struct myri10ge_priv *mgp = netdev_priv(netdev); + + if (pause->tx_pause != mgp->pause) + return myri10ge_change_pause(mgp, pause->tx_pause); + if (pause->rx_pause != mgp->pause) + return myri10ge_change_pause(mgp, pause->tx_pause); + if (pause->autoneg != 0) + return -EINVAL; + return 0; +} + +static void +myri10ge_get_ringparam(struct net_device *netdev, + struct ethtool_ringparam *ring) +{ + struct myri10ge_priv *mgp = netdev_priv(netdev); + + ring->rx_mini_max_pending = mgp->rx_small.mask + 1; + ring->rx_max_pending = mgp->rx_big.mask + 1; + ring->rx_jumbo_max_pending = 0; + ring->tx_max_pending = mgp->rx_small.mask + 1; + ring->rx_mini_pending = ring->rx_mini_max_pending; + ring->rx_pending = ring->rx_max_pending; + ring->rx_jumbo_pending = ring->rx_jumbo_max_pending; + ring->tx_pending = ring->tx_max_pending; +} + +static u32 myri10ge_get_rx_csum(struct net_device *netdev) +{ + struct myri10ge_priv *mgp = netdev_priv(netdev); + if (mgp->csum_flag) + return 1; + else + return 0; +} + +static int myri10ge_set_rx_csum(struct net_device *netdev, u32 csum_enabled) +{ + struct myri10ge_priv *mgp = netdev_priv(netdev); + if (csum_enabled) + mgp->csum_flag = MXGEFW_FLAGS_CKSUM; + else + mgp->csum_flag = 0; + return 0; +} + +static const char myri10ge_gstrings_stats[][ETH_GSTRING_LEN] = { + "rx_packets", "tx_packets", "rx_bytes", "tx_bytes", "rx_errors", + "tx_errors", "rx_dropped", "tx_dropped", "multicast", "collisions", + "rx_length_errors", "rx_over_errors", "rx_crc_errors", + "rx_frame_errors", "rx_fifo_errors", "rx_missed_errors", + "tx_aborted_errors", "tx_carrier_errors", "tx_fifo_errors", + "tx_heartbeat_errors", "tx_window_errors", + /* device-specific stats */ + "read_dma_bw_MBs", "write_dma_bw_MBs", "read_write_dma_bw_MBs", + "serial_number", "tx_pkt_start", "tx_pkt_done", + "tx_req", "tx_done", "rx_small_cnt", "rx_big_cnt", + "wake_queue", "stop_queue", "watchdog_resets", "tx_linearized", + "link_up", "dropped_link_overflow", "dropped_link_error_or_filtered", + "dropped_runt", "dropped_overrun", "dropped_no_small_buffer", + "dropped_no_big_buffer" +}; + +#define MYRI10GE_NET_STATS_LEN 21 +#define MYRI10GE_STATS_LEN sizeof(myri10ge_gstrings_stats) / ETH_GSTRING_LEN + +static void +myri10ge_get_strings(struct net_device *netdev, u32 stringset, u8 * data) +{ + switch (stringset) { + case ETH_SS_STATS: + memcpy(data, *myri10ge_gstrings_stats, + sizeof(myri10ge_gstrings_stats)); + break; + } +} + +static int myri10ge_get_stats_count(struct net_device *netdev) +{ + return MYRI10GE_STATS_LEN; +} + +static void +myri10ge_get_ethtool_stats(struct net_device *netdev, + struct ethtool_stats *stats, u64 * data) +{ + struct myri10ge_priv *mgp = netdev_priv(netdev); + int i; + + for (i = 0; i < MYRI10GE_NET_STATS_LEN; i++) + data[i] = ((unsigned long *)&mgp->stats)[i]; + + data[i++] = (unsigned int)mgp->read_dma; + data[i++] = (unsigned int)mgp->write_dma; + data[i++] = (unsigned int)mgp->read_write_dma; + data[i++] = (unsigned int)mgp->serial_number; + data[i++] = (unsigned int)mgp->tx.pkt_start; + data[i++] = (unsigned int)mgp->tx.pkt_done; + data[i++] = (unsigned int)mgp->tx.req; + data[i++] = (unsigned int)mgp->tx.done; + data[i++] = (unsigned int)mgp->rx_small.cnt; + data[i++] = (unsigned int)mgp->rx_big.cnt; + data[i++] = (unsigned int)mgp->wake_queue; + data[i++] = (unsigned int)mgp->stop_queue; + data[i++] = (unsigned int)mgp->watchdog_resets; + data[i++] = (unsigned int)mgp->tx_linearized; + data[i++] = (unsigned int)ntohl(mgp->fw_stats->link_up); + data[i++] = (unsigned int)ntohl(mgp->fw_stats->dropped_link_overflow); + data[i++] = + (unsigned int)ntohl(mgp->fw_stats->dropped_link_error_or_filtered); + data[i++] = (unsigned int)ntohl(mgp->fw_stats->dropped_runt); + data[i++] = (unsigned int)ntohl(mgp->fw_stats->dropped_overrun); + data[i++] = (unsigned int)ntohl(mgp->fw_stats->dropped_no_small_buffer); + data[i++] = (unsigned int)ntohl(mgp->fw_stats->dropped_no_big_buffer); +} + +static struct ethtool_ops myri10ge_ethtool_ops = { + .get_settings = myri10ge_get_settings, + .get_drvinfo = myri10ge_get_drvinfo, + .get_coalesce = myri10ge_get_coalesce, + .set_coalesce = myri10ge_set_coalesce, + .get_pauseparam = myri10ge_get_pauseparam, + .set_pauseparam = myri10ge_set_pauseparam, + .get_ringparam = myri10ge_get_ringparam, + .get_rx_csum = myri10ge_get_rx_csum, + .set_rx_csum = myri10ge_set_rx_csum, + .get_tx_csum = ethtool_op_get_tx_csum, + .set_tx_csum = ethtool_op_set_tx_csum, + .get_sg = ethtool_op_get_sg, + .set_sg = ethtool_op_set_sg, +#ifdef NETIF_F_TSO + .get_tso = ethtool_op_get_tso, + .set_tso = ethtool_op_set_tso, +#endif + .get_strings = myri10ge_get_strings, + .get_stats_count = myri10ge_get_stats_count, + .get_ethtool_stats = myri10ge_get_ethtool_stats +}; + +static int myri10ge_allocate_rings(struct net_device *dev) +{ + struct myri10ge_priv *mgp; + struct myri10ge_cmd cmd; + int tx_ring_size, rx_ring_size; + int tx_ring_entries, rx_ring_entries; + int i, status; + size_t bytes; + + mgp = netdev_priv(dev); + + /* get ring sizes */ + + status = myri10ge_send_cmd(mgp, MXGEFW_CMD_GET_SEND_RING_SIZE, &cmd, 0); + tx_ring_size = cmd.data0; + status |= myri10ge_send_cmd(mgp, MXGEFW_CMD_GET_RX_RING_SIZE, &cmd, 0); + rx_ring_size = cmd.data0; + + tx_ring_entries = tx_ring_size / sizeof(struct mcp_kreq_ether_send); + rx_ring_entries = rx_ring_size / sizeof(struct mcp_dma_addr); + mgp->tx.mask = tx_ring_entries - 1; + mgp->rx_small.mask = mgp->rx_big.mask = rx_ring_entries - 1; + + /* allocate the host shadow rings */ + + bytes = 8 + (MYRI10GE_MAX_SEND_DESC_TSO + 4) + * sizeof(*mgp->tx.req_list); + mgp->tx.req_bytes = kzalloc(bytes, GFP_KERNEL); + if (mgp->tx.req_bytes == NULL) + goto abort_with_nothing; + + /* ensure req_list entries are aligned to 8 bytes */ + mgp->tx.req_list = (struct mcp_kreq_ether_send *) + ALIGN((unsigned long)mgp->tx.req_bytes, 8); + + bytes = rx_ring_entries * sizeof(*mgp->rx_small.shadow); + mgp->rx_small.shadow = kzalloc(bytes, GFP_KERNEL); + if (mgp->rx_small.shadow == NULL) + goto abort_with_tx_req_bytes; + + bytes = rx_ring_entries * sizeof(*mgp->rx_big.shadow); + mgp->rx_big.shadow = kzalloc(bytes, GFP_KERNEL); + if (mgp->rx_big.shadow == NULL) + goto abort_with_rx_small_shadow; + + /* allocate the host info rings */ + + bytes = tx_ring_entries * sizeof(*mgp->tx.info); + mgp->tx.info = kzalloc(bytes, GFP_KERNEL); + if (mgp->tx.info == NULL) + goto abort_with_rx_big_shadow; + + bytes = rx_ring_entries * sizeof(*mgp->rx_small.info); + mgp->rx_small.info = kzalloc(bytes, GFP_KERNEL); + if (mgp->rx_small.info == NULL) + goto abort_with_tx_info; + + bytes = rx_ring_entries * sizeof(*mgp->rx_big.info); + mgp->rx_big.info = kzalloc(bytes, GFP_KERNEL); + if (mgp->rx_big.info == NULL) + goto abort_with_rx_small_info; + + /* Fill the receive rings */ + + for (i = 0; i <= mgp->rx_small.mask; i++) { + status = myri10ge_getbuf(&mgp->rx_small, mgp->pdev, + mgp->small_bytes, i); + if (status) { + printk(KERN_ERR + "myri10ge: %s: alloced only %d small bufs\n", + dev->name, i); + goto abort_with_rx_small_ring; + } + } + + for (i = 0; i <= mgp->rx_big.mask; i++) { + status = + myri10ge_getbuf(&mgp->rx_big, mgp->pdev, + dev->mtu + ETH_HLEN, i); + if (status) { + printk(KERN_ERR + "myri10ge: %s: alloced only %d big bufs\n", + dev->name, i); + goto abort_with_rx_big_ring; + } + } + + return 0; + +abort_with_rx_big_ring: + for (i = 0; i <= mgp->rx_big.mask; i++) { + if (mgp->rx_big.info[i].skb != NULL) + dev_kfree_skb_any(mgp->rx_big.info[i].skb); + if (pci_unmap_len(&mgp->rx_big.info[i], len)) + pci_unmap_single(mgp->pdev, + pci_unmap_addr(&mgp->rx_big.info[i], + bus), + pci_unmap_len(&mgp->rx_big.info[i], + len), + PCI_DMA_FROMDEVICE); + } + +abort_with_rx_small_ring: + for (i = 0; i <= mgp->rx_small.mask; i++) { + if (mgp->rx_small.info[i].skb != NULL) + dev_kfree_skb_any(mgp->rx_small.info[i].skb); + if (pci_unmap_len(&mgp->rx_small.info[i], len)) + pci_unmap_single(mgp->pdev, + pci_unmap_addr(&mgp->rx_small.info[i], + bus), + pci_unmap_len(&mgp->rx_small.info[i], + len), + PCI_DMA_FROMDEVICE); + } + kfree(mgp->rx_big.info); + +abort_with_rx_small_info: + kfree(mgp->rx_small.info); + +abort_with_tx_info: + kfree(mgp->tx.info); + +abort_with_rx_big_shadow: + kfree(mgp->rx_big.shadow); + +abort_with_rx_small_shadow: + kfree(mgp->rx_small.shadow); + +abort_with_tx_req_bytes: + kfree(mgp->tx.req_bytes); + mgp->tx.req_bytes = NULL; + mgp->tx.req_list = NULL; + +abort_with_nothing: + return status; +} + +static void myri10ge_free_rings(struct net_device *dev) +{ + struct myri10ge_priv *mgp; + struct sk_buff *skb; + struct myri10ge_tx_buf *tx; + int i, len, idx; + + mgp = netdev_priv(dev); + + for (i = 0; i <= mgp->rx_big.mask; i++) { + if (mgp->rx_big.info[i].skb != NULL) + dev_kfree_skb_any(mgp->rx_big.info[i].skb); + if (pci_unmap_len(&mgp->rx_big.info[i], len)) + pci_unmap_single(mgp->pdev, + pci_unmap_addr(&mgp->rx_big.info[i], + bus), + pci_unmap_len(&mgp->rx_big.info[i], + len), + PCI_DMA_FROMDEVICE); + } + + for (i = 0; i <= mgp->rx_small.mask; i++) { + if (mgp->rx_small.info[i].skb != NULL) + dev_kfree_skb_any(mgp->rx_small.info[i].skb); + if (pci_unmap_len(&mgp->rx_small.info[i], len)) + pci_unmap_single(mgp->pdev, + pci_unmap_addr(&mgp->rx_small.info[i], + bus), + pci_unmap_len(&mgp->rx_small.info[i], + len), + PCI_DMA_FROMDEVICE); + } + + tx = &mgp->tx; + while (tx->done != tx->req) { + idx = tx->done & tx->mask; + skb = tx->info[idx].skb; + + /* Mark as free */ + tx->info[idx].skb = NULL; + tx->done++; + len = pci_unmap_len(&tx->info[idx], len); + pci_unmap_len_set(&tx->info[idx], len, 0); + if (skb) { + mgp->stats.tx_dropped++; + dev_kfree_skb_any(skb); + if (len) + pci_unmap_single(mgp->pdev, + pci_unmap_addr(&tx->info[idx], + bus), len, + PCI_DMA_TODEVICE); + } else { + if (len) + pci_unmap_page(mgp->pdev, + pci_unmap_addr(&tx->info[idx], + bus), len, + PCI_DMA_TODEVICE); + } + } + kfree(mgp->rx_big.info); + + kfree(mgp->rx_small.info); + + kfree(mgp->tx.info); + + kfree(mgp->rx_big.shadow); + + kfree(mgp->rx_small.shadow); + + kfree(mgp->tx.req_bytes); + mgp->tx.req_bytes = NULL; + mgp->tx.req_list = NULL; +} + +static int myri10ge_open(struct net_device *dev) +{ + struct myri10ge_priv *mgp; + struct myri10ge_cmd cmd; + int status, big_pow2; + + mgp = netdev_priv(dev); + + if (mgp->running != MYRI10GE_ETH_STOPPED) + return -EBUSY; + + mgp->running = MYRI10GE_ETH_STARTING; + status = myri10ge_reset(mgp); + if (status != 0) { + printk(KERN_ERR "myri10ge: %s: failed reset\n", dev->name); + mgp->running = MYRI10GE_ETH_STOPPED; + return -ENXIO; + } + + /* decide what small buffer size to use. For good TCP rx + * performance, it is important to not receive 1514 byte + * frames into jumbo buffers, as it confuses the socket buffer + * accounting code, leading to drops and erratic performance. + */ + + if (dev->mtu <= ETH_DATA_LEN) + mgp->small_bytes = 128; /* enough for a TCP header */ + else + mgp->small_bytes = ETH_FRAME_LEN; /* enough for an ETH_DATA_LEN frame */ + + /* Override the small buffer size? */ + if (myri10ge_small_bytes > 0) + mgp->small_bytes = myri10ge_small_bytes; + + /* If the user sets an obscenely small MTU, adjust the small + * bytes down to nearly nothing */ + if (mgp->small_bytes >= (dev->mtu + ETH_HLEN)) + mgp->small_bytes = 64; + + /* get the lanai pointers to the send and receive rings */ + + status |= myri10ge_send_cmd(mgp, MXGEFW_CMD_GET_SEND_OFFSET, &cmd, 0); + mgp->tx.lanai = + (struct mcp_kreq_ether_send __iomem *)(mgp->sram + cmd.data0); + + status |= + myri10ge_send_cmd(mgp, MXGEFW_CMD_GET_SMALL_RX_OFFSET, &cmd, 0); + mgp->rx_small.lanai = + (struct mcp_kreq_ether_recv __iomem *)(mgp->sram + cmd.data0); + + status |= myri10ge_send_cmd(mgp, MXGEFW_CMD_GET_BIG_RX_OFFSET, &cmd, 0); + mgp->rx_big.lanai = + (struct mcp_kreq_ether_recv __iomem *)(mgp->sram + cmd.data0); + + if (status != 0) { + printk(KERN_ERR + "myri10ge: %s: failed to get ring sizes or locations\n", + dev->name); + mgp->running = MYRI10GE_ETH_STOPPED; + return -ENXIO; + } + + if (mgp->mtrr >= 0) { + mgp->tx.wc_fifo = (u8 __iomem *) mgp->sram + 0x200000; + mgp->rx_small.wc_fifo = (u8 __iomem *) mgp->sram + 0x300000; + mgp->rx_big.wc_fifo = (u8 __iomem *) mgp->sram + 0x340000; + } else { + mgp->tx.wc_fifo = NULL; + mgp->rx_small.wc_fifo = NULL; + mgp->rx_big.wc_fifo = NULL; + } + + status = myri10ge_allocate_rings(dev); + if (status != 0) + goto abort_with_nothing; + + /* Firmware needs the big buff size as a power of 2. Lie and + * tell him the buffer is larger, because we only use 1 + * buffer/pkt, and the mtu will prevent overruns. + */ + big_pow2 = dev->mtu + ETH_HLEN + MXGEFW_PAD; + while ((big_pow2 & (big_pow2 - 1)) != 0) + big_pow2++; + + /* now give firmware buffers sizes, and MTU */ + cmd.data0 = dev->mtu + ETH_HLEN + VLAN_HLEN; + status = myri10ge_send_cmd(mgp, MXGEFW_CMD_SET_MTU, &cmd, 0); + cmd.data0 = mgp->small_bytes; + status |= + myri10ge_send_cmd(mgp, MXGEFW_CMD_SET_SMALL_BUFFER_SIZE, &cmd, 0); + cmd.data0 = big_pow2; + status |= + myri10ge_send_cmd(mgp, MXGEFW_CMD_SET_BIG_BUFFER_SIZE, &cmd, 0); + if (status) { + printk(KERN_ERR "myri10ge: %s: Couldn't set buffer sizes\n", + dev->name); + goto abort_with_rings; + } + + cmd.data0 = MYRI10GE_LOWPART_TO_U32(mgp->fw_stats_bus); + cmd.data1 = MYRI10GE_HIGHPART_TO_U32(mgp->fw_stats_bus); + status = myri10ge_send_cmd(mgp, MXGEFW_CMD_SET_STATS_DMA, &cmd, 0); + if (status) { + printk(KERN_ERR "myri10ge: %s: Couldn't set stats DMA\n", + dev->name); + goto abort_with_rings; + } + + mgp->link_state = -1; + mgp->rdma_tags_available = 15; + + netif_poll_enable(mgp->dev); /* must happen prior to any irq */ + + status = myri10ge_send_cmd(mgp, MXGEFW_CMD_ETHERNET_UP, &cmd, 0); + if (status) { + printk(KERN_ERR "myri10ge: %s: Couldn't bring up link\n", + dev->name); + goto abort_with_rings; + } + + mgp->wake_queue = 0; + mgp->stop_queue = 0; + mgp->running = MYRI10GE_ETH_RUNNING; + mgp->watchdog_timer.expires = jiffies + myri10ge_watchdog_timeout * HZ; + add_timer(&mgp->watchdog_timer); + netif_wake_queue(dev); + return 0; + +abort_with_rings: + myri10ge_free_rings(dev); + +abort_with_nothing: + mgp->running = MYRI10GE_ETH_STOPPED; + return -ENOMEM; +} + +static int myri10ge_close(struct net_device *dev) +{ + struct myri10ge_priv *mgp; + struct myri10ge_cmd cmd; + int status, old_down_cnt; + + mgp = netdev_priv(dev); + + if (mgp->running != MYRI10GE_ETH_RUNNING) + return 0; + + if (mgp->tx.req_bytes == NULL) + return 0; + + del_timer_sync(&mgp->watchdog_timer); + mgp->running = MYRI10GE_ETH_STOPPING; + netif_poll_disable(mgp->dev); + netif_carrier_off(dev); + netif_stop_queue(dev); + old_down_cnt = mgp->down_cnt; + mb(); + status = myri10ge_send_cmd(mgp, MXGEFW_CMD_ETHERNET_DOWN, &cmd, 0); + if (status) + printk(KERN_ERR "myri10ge: %s: Couldn't bring down link\n", + dev->name); + + wait_event_timeout(mgp->down_wq, old_down_cnt != mgp->down_cnt, HZ); + if (old_down_cnt == mgp->down_cnt) + printk(KERN_ERR "myri10ge: %s never got down irq\n", dev->name); + + netif_tx_disable(dev); + + myri10ge_free_rings(dev); + + mgp->running = MYRI10GE_ETH_STOPPED; + return 0; +} + +/* copy an array of struct mcp_kreq_ether_send's to the mcp. Copy + * backwards one at a time and handle ring wraps */ + +static inline void +myri10ge_submit_req_backwards(struct myri10ge_tx_buf *tx, + struct mcp_kreq_ether_send *src, int cnt) +{ + int idx, starting_slot; + starting_slot = tx->req; + while (cnt > 1) { + cnt--; + idx = (starting_slot + cnt) & tx->mask; + myri10ge_pio_copy(&tx->lanai[idx], &src[cnt], sizeof(*src)); + mb(); + } +} + +/* + * copy an array of struct mcp_kreq_ether_send's to the mcp. Copy + * at most 32 bytes at a time, so as to avoid involving the software + * pio handler in the nic. We re-write the first segment's flags + * to mark them valid only after writing the entire chain. + */ + +static inline void +myri10ge_submit_req(struct myri10ge_tx_buf *tx, struct mcp_kreq_ether_send *src, + int cnt) +{ + int idx, i; + struct mcp_kreq_ether_send __iomem *dstp, *dst; + struct mcp_kreq_ether_send *srcp; + u8 last_flags; + + idx = tx->req & tx->mask; + + last_flags = src->flags; + src->flags = 0; + mb(); + dst = dstp = &tx->lanai[idx]; + srcp = src; + + if ((idx + cnt) < tx->mask) { + for (i = 0; i < (cnt - 1); i += 2) { + myri10ge_pio_copy(dstp, srcp, 2 * sizeof(*src)); + mb(); /* force write every 32 bytes */ + srcp += 2; + dstp += 2; + } + } else { + /* submit all but the first request, and ensure + * that it is submitted below */ + myri10ge_submit_req_backwards(tx, src, cnt); + i = 0; + } + if (i < cnt) { + /* submit the first request */ + myri10ge_pio_copy(dstp, srcp, sizeof(*src)); + mb(); /* barrier before setting valid flag */ + } + + /* re-write the last 32-bits with the valid flags */ + src->flags = last_flags; + __raw_writel(*((u32 *) src + 3), (u32 __iomem *) dst + 3); + tx->req += cnt; + mb(); +} + +static inline void +myri10ge_submit_req_wc(struct myri10ge_tx_buf *tx, + struct mcp_kreq_ether_send *src, int cnt) +{ + tx->req += cnt; + mb(); + while (cnt >= 4) { + myri10ge_pio_copy(tx->wc_fifo, src, 64); + mb(); + src += 4; + cnt -= 4; + } + if (cnt > 0) { + /* pad it to 64 bytes. The src is 64 bytes bigger than it + * needs to be so that we don't overrun it */ + myri10ge_pio_copy(tx->wc_fifo + (cnt << 18), src, 64); + mb(); + } +} + +/* + * Transmit a packet. We need to split the packet so that a single + * segment does not cross myri10ge->tx.boundary, so this makes segment + * counting tricky. So rather than try to count segments up front, we + * just give up if there are too few segments to hold a reasonably + * fragmented packet currently available. If we run + * out of segments while preparing a packet for DMA, we just linearize + * it and try again. + */ + +static int myri10ge_xmit(struct sk_buff *skb, struct net_device *dev) +{ + struct myri10ge_priv *mgp = netdev_priv(dev); + struct mcp_kreq_ether_send *req; + struct myri10ge_tx_buf *tx = &mgp->tx; + struct skb_frag_struct *frag; + dma_addr_t bus; + u32 low, high_swapped; + unsigned int len; + int idx, last_idx, avail, frag_cnt, frag_idx, count, mss, max_segments; + u16 pseudo_hdr_offset, cksum_offset; + int cum_len, seglen, boundary, rdma_count; + u8 flags, odd_flag; + +again: + req = tx->req_list; + avail = tx->mask - 1 - (tx->req - tx->done); + + mss = 0; + max_segments = MXGEFW_MAX_SEND_DESC; + +#ifdef NETIF_F_TSO + if (skb->len > (dev->mtu + ETH_HLEN)) { + mss = skb_shinfo(skb)->tso_size; + if (mss != 0) + max_segments = MYRI10GE_MAX_SEND_DESC_TSO; + } +#endif /*NETIF_F_TSO */ + + if ((unlikely(avail < max_segments))) { + /* we are out of transmit resources */ + mgp->stop_queue++; + netif_stop_queue(dev); + return 1; + } + + /* Setup checksum offloading, if needed */ + cksum_offset = 0; + pseudo_hdr_offset = 0; + odd_flag = 0; + flags = (MXGEFW_FLAGS_NO_TSO | MXGEFW_FLAGS_FIRST); + if (likely(skb->ip_summed == CHECKSUM_HW)) { + cksum_offset = (skb->h.raw - skb->data); + pseudo_hdr_offset = (skb->h.raw + skb->csum) - skb->data; + /* If the headers are excessively large, then we must + * fall back to a software checksum */ + if (unlikely(cksum_offset > 255 || pseudo_hdr_offset > 127)) { + if (skb_checksum_help(skb, 0)) + goto drop; + cksum_offset = 0; + pseudo_hdr_offset = 0; + } else { + pseudo_hdr_offset = htons(pseudo_hdr_offset); + odd_flag = MXGEFW_FLAGS_ALIGN_ODD; + flags |= MXGEFW_FLAGS_CKSUM; + } + } + + cum_len = 0; + +#ifdef NETIF_F_TSO + if (mss) { /* TSO */ + /* this removes any CKSUM flag from before */ + flags = (MXGEFW_FLAGS_TSO_HDR | MXGEFW_FLAGS_FIRST); + + /* negative cum_len signifies to the + * send loop that we are still in the + * header portion of the TSO packet. + * TSO header must be at most 134 bytes long */ + cum_len = -((skb->h.raw - skb->data) + (skb->h.th->doff << 2)); + + /* for TSO, pseudo_hdr_offset holds mss. + * The firmware figures out where to put + * the checksum by parsing the header. */ + pseudo_hdr_offset = htons(mss); + } else +#endif /*NETIF_F_TSO */ + /* Mark small packets, and pad out tiny packets */ + if (skb->len <= MXGEFW_SEND_SMALL_SIZE) { + flags |= MXGEFW_FLAGS_SMALL; + + /* pad frames to at least ETH_ZLEN bytes */ + if (unlikely(skb->len < ETH_ZLEN)) { + skb = skb_padto(skb, ETH_ZLEN); + if (skb == NULL) { + /* The packet is gone, so we must + * return 0 */ + mgp->stats.tx_dropped += 1; + return 0; + } + /* adjust the len to account for the zero pad + * so that the nic can know how long it is */ + skb->len = ETH_ZLEN; + } + } + + /* map the skb for DMA */ + len = skb->len - skb->data_len; + idx = tx->req & tx->mask; + tx->info[idx].skb = skb; + bus = pci_map_single(mgp->pdev, skb->data, len, PCI_DMA_TODEVICE); + pci_unmap_addr_set(&tx->info[idx], bus, bus); + pci_unmap_len_set(&tx->info[idx], len, len); + + frag_cnt = skb_shinfo(skb)->nr_frags; + frag_idx = 0; + count = 0; + rdma_count = 0; + + /* "rdma_count" is the number of RDMAs belonging to the + * current packet BEFORE the current send request. For + * non-TSO packets, this is equal to "count". + * For TSO packets, rdma_count needs to be reset + * to 0 after a segment cut. + * + * The rdma_count field of the send request is + * the number of RDMAs of the packet starting at + * that request. For TSO send requests with one ore more cuts + * in the middle, this is the number of RDMAs starting + * after the last cut in the request. All previous + * segments before the last cut implicitly have 1 RDMA. + * + * Since the number of RDMAs is not known beforehand, + * it must be filled-in retroactively - after each + * segmentation cut or at the end of the entire packet. + */ + + while (1) { + /* Break the SKB or Fragment up into pieces which + * do not cross mgp->tx.boundary */ + low = MYRI10GE_LOWPART_TO_U32(bus); + high_swapped = htonl(MYRI10GE_HIGHPART_TO_U32(bus)); + while (len) { + u8 flags_next; + int cum_len_next; + + if (unlikely(count == max_segments)) + goto abort_linearize; + + boundary = (low + tx->boundary) & ~(tx->boundary - 1); + seglen = boundary - low; + if (seglen > len) + seglen = len; + flags_next = flags & ~MXGEFW_FLAGS_FIRST; + cum_len_next = cum_len + seglen; +#ifdef NETIF_F_TSO + if (mss) { /* TSO */ + (req - rdma_count)->rdma_count = rdma_count + 1; + + if (likely(cum_len >= 0)) { /* payload */ + int next_is_first, chop; + + chop = (cum_len_next > mss); + cum_len_next = cum_len_next % mss; + next_is_first = (cum_len_next == 0); + flags |= chop * MXGEFW_FLAGS_TSO_CHOP; + flags_next |= next_is_first * + MXGEFW_FLAGS_FIRST; + rdma_count |= -(chop | next_is_first); + rdma_count += chop & !next_is_first; + } else if (likely(cum_len_next >= 0)) { /* header ends */ + int small; + + rdma_count = -1; + cum_len_next = 0; + seglen = -cum_len; + small = (mss <= MXGEFW_SEND_SMALL_SIZE); + flags_next = MXGEFW_FLAGS_TSO_PLD | + MXGEFW_FLAGS_FIRST | + (small * MXGEFW_FLAGS_SMALL); + } + } +#endif /* NETIF_F_TSO */ + req->addr_high = high_swapped; + req->addr_low = htonl(low); + req->pseudo_hdr_offset = pseudo_hdr_offset; + req->pad = 0; /* complete solid 16-byte block; does this matter? */ + req->rdma_count = 1; + req->length = htons(seglen); + req->cksum_offset = cksum_offset; + req->flags = flags | ((cum_len & 1) * odd_flag); + + low += seglen; + len -= seglen; + cum_len = cum_len_next; + flags = flags_next; + req++; + count++; + rdma_count++; + if (unlikely(cksum_offset > seglen)) + cksum_offset -= seglen; + else + cksum_offset = 0; + } + if (frag_idx == frag_cnt) + break; + + /* map next fragment for DMA */ + idx = (count + tx->req) & tx->mask; + frag = &skb_shinfo(skb)->frags[frag_idx]; + frag_idx++; + len = frag->size; + bus = pci_map_page(mgp->pdev, frag->page, frag->page_offset, + len, PCI_DMA_TODEVICE); + pci_unmap_addr_set(&tx->info[idx], bus, bus); + pci_unmap_len_set(&tx->info[idx], len, len); + } + + (req - rdma_count)->rdma_count = rdma_count; +#ifdef NETIF_F_TSO + if (mss) + do { + req--; + req->flags |= MXGEFW_FLAGS_TSO_LAST; + } while (!(req->flags & (MXGEFW_FLAGS_TSO_CHOP | + MXGEFW_FLAGS_FIRST))); +#endif + idx = ((count - 1) + tx->req) & tx->mask; + tx->info[idx].last = 1; + if (tx->wc_fifo == NULL) + myri10ge_submit_req(tx, tx->req_list, count); + else + myri10ge_submit_req_wc(tx, tx->req_list, count); + tx->pkt_start++; + if ((avail - count) < MXGEFW_MAX_SEND_DESC) { + mgp->stop_queue++; + netif_stop_queue(dev); + } + dev->trans_start = jiffies; + return 0; + +abort_linearize: + /* Free any DMA resources we've alloced and clear out the skb + * slot so as to not trip up assertions, and to avoid a + * double-free if linearizing fails */ + + last_idx = (idx + 1) & tx->mask; + idx = tx->req & tx->mask; + tx->info[idx].skb = NULL; + do { + len = pci_unmap_len(&tx->info[idx], len); + if (len) { + if (tx->info[idx].skb != NULL) + pci_unmap_single(mgp->pdev, + pci_unmap_addr(&tx->info[idx], + bus), len, + PCI_DMA_TODEVICE); + else + pci_unmap_page(mgp->pdev, + pci_unmap_addr(&tx->info[idx], + bus), len, + PCI_DMA_TODEVICE); + pci_unmap_len_set(&tx->info[idx], len, 0); + tx->info[idx].skb = NULL; + } + idx = (idx + 1) & tx->mask; + } while (idx != last_idx); + if (skb_shinfo(skb)->tso_size) { + printk(KERN_ERR + "myri10ge: %s: TSO but wanted to linearize?!?!?\n", + mgp->dev->name); + goto drop; + } + + if (skb_linearize(skb, GFP_ATOMIC)) + goto drop; + + mgp->tx_linearized++; + goto again; + +drop: + dev_kfree_skb_any(skb); + mgp->stats.tx_dropped += 1; + return 0; + +} + +static struct net_device_stats *myri10ge_get_stats(struct net_device *dev) +{ + struct myri10ge_priv *mgp = netdev_priv(dev); + return &mgp->stats; +} + +static void myri10ge_set_multicast_list(struct net_device *dev) +{ + /* can be called from atomic contexts, + * pass 1 to force atomicity in myri10ge_send_cmd() */ + myri10ge_change_promisc(netdev_priv(dev), dev->flags & IFF_PROMISC, 1); +} + +static int myri10ge_set_mac_address(struct net_device *dev, void *addr) +{ + struct sockaddr *sa = addr; + struct myri10ge_priv *mgp = netdev_priv(dev); + int status; + + if (!is_valid_ether_addr(sa->sa_data)) + return -EADDRNOTAVAIL; + + status = myri10ge_update_mac_address(mgp, sa->sa_data); + if (status != 0) { + printk(KERN_ERR + "myri10ge: %s: changing mac address failed with %d\n", + dev->name, status); + return status; + } + + /* change the dev structure */ + memcpy(dev->dev_addr, sa->sa_data, 6); + return 0; +} + +static int myri10ge_change_mtu(struct net_device *dev, int new_mtu) +{ + struct myri10ge_priv *mgp = netdev_priv(dev); + int error = 0; + + if ((new_mtu < 68) || (ETH_HLEN + new_mtu > MYRI10GE_MAX_ETHER_MTU)) { + printk(KERN_ERR "myri10ge: %s: new mtu (%d) is not valid\n", + dev->name, new_mtu); + return -EINVAL; + } + printk(KERN_INFO "%s: changing mtu from %d to %d\n", + dev->name, dev->mtu, new_mtu); + if (mgp->running) { + /* if we change the mtu on an active device, we must + * reset the device so the firmware sees the change */ + myri10ge_close(dev); + dev->mtu = new_mtu; + myri10ge_open(dev); + } else + dev->mtu = new_mtu; + + return error; +} + +/* + * Enable ECRC to align PCI-E Completion packets on an 8-byte boundary. + * Only do it if the bridge is a root port since we don't want to disturb + * any other device, except if forced with myri10ge_ecrc_enable > 1. + */ + +#define PCI_DEVICE_ID_NVIDIA_NFORCE_CK804_PCIE 0x005d + +static void myri10ge_enable_ecrc(struct myri10ge_priv *mgp) +{ + struct pci_dev *bridge = mgp->pdev->bus->self; + struct device *dev = &mgp->pdev->dev; + unsigned cap; + unsigned err_cap; + u16 val; + u8 ext_type; + int ret; + + if (!myri10ge_ecrc_enable || !bridge) + return; + + /* check that the bridge is a root port */ + cap = pci_find_capability(bridge, PCI_CAP_ID_EXP); + pci_read_config_word(bridge, cap + PCI_CAP_FLAGS, &val); + ext_type = (val & PCI_EXP_FLAGS_TYPE) >> 4; + if (ext_type != PCI_EXP_TYPE_ROOT_PORT) { + if (myri10ge_ecrc_enable > 1) { + struct pci_dev *old_bridge = bridge; + + /* Walk the hierarchy up to the root port + * where ECRC has to be enabled */ + do { + bridge = bridge->bus->self; + if (!bridge) { + dev_err(dev, + "Failed to find root port" + " to force ECRC\n"); + return; + } + cap = + pci_find_capability(bridge, PCI_CAP_ID_EXP); + pci_read_config_word(bridge, + cap + PCI_CAP_FLAGS, &val); + ext_type = (val & PCI_EXP_FLAGS_TYPE) >> 4; + } while (ext_type != PCI_EXP_TYPE_ROOT_PORT); + + dev_info(dev, + "Forcing ECRC on non-root port %s" + " (enabling on root port %s)\n", + pci_name(old_bridge), pci_name(bridge)); + } else { + dev_err(dev, + "Not enabling ECRC on non-root port %s\n", + pci_name(bridge)); + return; + } + } + + cap = pci_find_ext_capability(bridge, PCI_EXT_CAP_ID_ERR); + /* nvidia ext cap is not always linked in ext cap chain */ + if (!cap + && bridge->vendor == PCI_VENDOR_ID_NVIDIA + && bridge->device == PCI_DEVICE_ID_NVIDIA_NFORCE_CK804_PCIE) + cap = 0x160; + + if (!cap) + return; + + ret = pci_read_config_dword(bridge, cap + PCI_ERR_CAP, &err_cap); + if (ret) { + dev_err(dev, "failed reading ext-conf-space of %s\n", + pci_name(bridge)); + dev_err(dev, "\t pci=nommconf in use? " + "or buggy/incomplete/absent ACPI MCFG attr?\n"); + return; + } + if (!(err_cap & PCI_ERR_CAP_ECRC_GENC)) + return; + + err_cap |= PCI_ERR_CAP_ECRC_GENE; + pci_write_config_dword(bridge, cap + PCI_ERR_CAP, err_cap); + dev_info(dev, "Enabled ECRC on upstream bridge %s\n", pci_name(bridge)); + mgp->tx.boundary = 4096; + mgp->fw_name = myri10ge_fw_aligned; +} + +/* + * The Lanai Z8E PCI-E interface achieves higher Read-DMA throughput + * when the PCI-E Completion packets are aligned on an 8-byte + * boundary. Some PCI-E chip sets always align Completion packets; on + * the ones that do not, the alignment can be enforced by enabling + * ECRC generation (if supported). + * + * When PCI-E Completion packets are not aligned, it is actually more + * efficient to limit Read-DMA transactions to 2KB, rather than 4KB. + * + * If the driver can neither enable ECRC nor verify that it has + * already been enabled, then it must use a firmware image which works + * around unaligned completion packets (myri10ge_ethp_z8e.dat), and it + * should also ensure that it never gives the device a Read-DMA which is + * larger than 2KB by setting the tx.boundary to 2KB. If ECRC is + * enabled, then the driver should use the aligned (myri10ge_eth_z8e.dat) + * firmware image, and set tx.boundary to 4KB. + */ + +#define PCI_DEVICE_ID_SERVERWORKS_HT2000_PCIE 0x0132 + +static void myri10ge_select_firmware(struct myri10ge_priv *mgp) +{ + struct pci_dev *bridge = mgp->pdev->bus->self; + + mgp->tx.boundary = 2048; + mgp->fw_name = myri10ge_fw_unaligned; + + if (myri10ge_force_firmware == 0) { + myri10ge_enable_ecrc(mgp); + + /* Check to see if the upstream bridge is known to + * provide aligned completions */ + if (bridge + /* ServerWorks HT2000/HT1000 */ + && bridge->vendor == PCI_VENDOR_ID_SERVERWORKS + && bridge->device == + PCI_DEVICE_ID_SERVERWORKS_HT2000_PCIE) { + dev_info(&mgp->pdev->dev, + "Assuming aligned completions (0x%x:0x%x)\n", + bridge->vendor, bridge->device); + mgp->tx.boundary = 4096; + mgp->fw_name = myri10ge_fw_aligned; + } + } else { + if (myri10ge_force_firmware == 1) { + dev_info(&mgp->pdev->dev, + "Assuming aligned completions (forced)\n"); + mgp->tx.boundary = 4096; + mgp->fw_name = myri10ge_fw_aligned; + } else { + dev_info(&mgp->pdev->dev, + "Assuming unaligned completions (forced)\n"); + mgp->tx.boundary = 2048; + mgp->fw_name = myri10ge_fw_unaligned; + } + } + if (myri10ge_fw_name != NULL) { + dev_info(&mgp->pdev->dev, "overriding firmware to %s\n", + myri10ge_fw_name); + mgp->fw_name = myri10ge_fw_name; + } +} + +static void myri10ge_save_state(struct myri10ge_priv *mgp) +{ + struct pci_dev *pdev = mgp->pdev; + int cap; + + pci_save_state(pdev); + /* now save PCIe and MSI state that Linux will not + * save for us */ + cap = pci_find_capability(pdev, PCI_CAP_ID_EXP); + pci_read_config_dword(pdev, cap + PCI_EXP_DEVCTL, &mgp->devctl); + cap = pci_find_capability(pdev, PCI_CAP_ID_MSI); + pci_read_config_word(pdev, cap + PCI_MSI_FLAGS, &mgp->msi_flags); +} + +static void myri10ge_restore_state(struct myri10ge_priv *mgp) +{ + struct pci_dev *pdev = mgp->pdev; + int cap; + + /* restore PCIe and MSI state that linux will not */ + cap = pci_find_capability(pdev, PCI_CAP_ID_EXP); + pci_write_config_dword(pdev, cap + PCI_CAP_ID_EXP, mgp->devctl); + cap = pci_find_capability(pdev, PCI_CAP_ID_MSI); + pci_write_config_word(pdev, cap + PCI_MSI_FLAGS, mgp->msi_flags); + + pci_restore_state(pdev); +} + +#ifdef CONFIG_PM + +static int myri10ge_suspend(struct pci_dev *pdev, pm_message_t state) +{ + struct myri10ge_priv *mgp; + struct net_device *netdev; + + mgp = pci_get_drvdata(pdev); + if (mgp == NULL) + return -EINVAL; + netdev = mgp->dev; + + netif_device_detach(netdev); + if (netif_running(netdev)) { + printk(KERN_INFO "myri10ge: closing %s\n", netdev->name); + rtnl_lock(); + myri10ge_close(netdev); + rtnl_unlock(); + } + myri10ge_dummy_rdma(mgp, 0); + free_irq(pdev->irq, mgp); + myri10ge_save_state(mgp); + pci_disable_device(pdev); + pci_set_power_state(pdev, pci_choose_state(pdev, state)); + return 0; +} + +static int myri10ge_resume(struct pci_dev *pdev) +{ + struct myri10ge_priv *mgp; + struct net_device *netdev; + int status; + u16 vendor; + + mgp = pci_get_drvdata(pdev); + if (mgp == NULL) + return -EINVAL; + netdev = mgp->dev; + pci_set_power_state(pdev, 0); /* zeros conf space as a side effect */ + msleep(5); /* give card time to respond */ + pci_read_config_word(mgp->pdev, PCI_VENDOR_ID, &vendor); + if (vendor == 0xffff) { + printk(KERN_ERR "myri10ge: %s: device disappeared!\n", + mgp->dev->name); + return -EIO; + } + myri10ge_restore_state(mgp); + pci_enable_device(pdev); + pci_set_master(pdev); + + status = request_irq(pdev->irq, myri10ge_intr, SA_SHIRQ, + netdev->name, mgp); + if (status != 0) { + dev_err(&pdev->dev, "failed to allocate IRQ\n"); + goto abort_with_msi; + } + + myri10ge_reset(mgp); + myri10ge_dummy_rdma(mgp, mgp->tx.boundary != 4096); + + /* Save configuration space to be restored if the + * nic resets due to a parity error */ + myri10ge_save_state(mgp); + + if (netif_running(netdev)) { + rtnl_lock(); + myri10ge_open(netdev); + rtnl_unlock(); + } + netif_device_attach(netdev); + + return 0; + +abort_with_msi: + return -EIO; + +} + +#endif /* CONFIG_PM */ + +static u32 myri10ge_read_reboot(struct myri10ge_priv *mgp) +{ + struct pci_dev *pdev = mgp->pdev; + int vs = mgp->vendor_specific_offset; + u32 reboot; + + /*enter read32 mode */ + pci_write_config_byte(pdev, vs + 0x10, 0x3); + + /*read REBOOT_STATUS (0xfffffff0) */ + pci_write_config_dword(pdev, vs + 0x18, 0xfffffff0); + pci_read_config_dword(pdev, vs + 0x14, &reboot); + return reboot; +} + +/* + * This watchdog is used to check whether the board has suffered + * from a parity error and needs to be recovered. + */ +static void myri10ge_watchdog(void *arg) +{ + struct myri10ge_priv *mgp = arg; + u32 reboot; + int status; + u16 cmd, vendor; + + mgp->watchdog_resets++; + pci_read_config_word(mgp->pdev, PCI_COMMAND, &cmd); + if ((cmd & PCI_COMMAND_MASTER) == 0) { + /* Bus master DMA disabled? Check to see + * if the card rebooted due to a parity error + * For now, just report it */ + reboot = myri10ge_read_reboot(mgp); + printk(KERN_ERR + "myri10ge: %s: NIC rebooted (0x%x), resetting\n", + mgp->dev->name, reboot); + /* + * A rebooted nic will come back with config space as + * it was after power was applied to PCIe bus. + * Attempt to restore config space which was saved + * when the driver was loaded, or the last time the + * nic was resumed from power saving mode. + */ + myri10ge_restore_state(mgp); + } else { + /* if we get back -1's from our slot, perhaps somebody + * powered off our card. Don't try to reset it in + * this case */ + if (cmd == 0xffff) { + pci_read_config_word(mgp->pdev, PCI_VENDOR_ID, &vendor); + if (vendor == 0xffff) { + printk(KERN_ERR + "myri10ge: %s: device disappeared!\n", + mgp->dev->name); + return; + } + } + /* Perhaps it is a software error. Try to reset */ + + printk(KERN_ERR "myri10ge: %s: device timeout, resetting\n", + mgp->dev->name); + printk(KERN_INFO "myri10ge: %s: %d %d %d %d %d\n", + mgp->dev->name, mgp->tx.req, mgp->tx.done, + mgp->tx.pkt_start, mgp->tx.pkt_done, + (int)ntohl(mgp->fw_stats->send_done_count)); + msleep(2000); + printk(KERN_INFO "myri10ge: %s: %d %d %d %d %d\n", + mgp->dev->name, mgp->tx.req, mgp->tx.done, + mgp->tx.pkt_start, mgp->tx.pkt_done, + (int)ntohl(mgp->fw_stats->send_done_count)); + } + rtnl_lock(); + myri10ge_close(mgp->dev); + status = myri10ge_load_firmware(mgp); + if (status != 0) + printk(KERN_ERR "myri10ge: %s: failed to load firmware\n", + mgp->dev->name); + else + myri10ge_open(mgp->dev); + rtnl_unlock(); +} + +/* + * We use our own timer routine rather than relying upon + * netdev->tx_timeout because we have a very large hardware transmit + * queue. Due to the large queue, the netdev->tx_timeout function + * cannot detect a NIC with a parity error in a timely fashion if the + * NIC is lightly loaded. + */ +static void myri10ge_watchdog_timer(unsigned long arg) +{ + struct myri10ge_priv *mgp; + + mgp = (struct myri10ge_priv *)arg; + if (mgp->tx.req != mgp->tx.done && + mgp->tx.done == mgp->watchdog_tx_done) + /* nic seems like it might be stuck.. */ + schedule_work(&mgp->watchdog_work); + else + /* rearm timer */ + mod_timer(&mgp->watchdog_timer, + jiffies + myri10ge_watchdog_timeout * HZ); + + mgp->watchdog_tx_done = mgp->tx.done; +} + +static int myri10ge_probe(struct pci_dev *pdev, const struct pci_device_id *ent) +{ + struct net_device *netdev; + struct myri10ge_priv *mgp; + struct device *dev = &pdev->dev; + size_t bytes; + int i; + int status = -ENXIO; + int cap; + int dac_enabled; + u16 val; + + netdev = alloc_etherdev(sizeof(*mgp)); + if (netdev == NULL) { + dev_err(dev, "Could not allocate ethernet device\n"); + return -ENOMEM; + } + + mgp = netdev_priv(netdev); + memset(mgp, 0, sizeof(*mgp)); + mgp->dev = netdev; + mgp->pdev = pdev; + mgp->csum_flag = MXGEFW_FLAGS_CKSUM; + mgp->pause = myri10ge_flow_control; + mgp->intr_coal_delay = myri10ge_intr_coal_delay; + init_waitqueue_head(&mgp->down_wq); + + if (pci_enable_device(pdev)) { + dev_err(&pdev->dev, "pci_enable_device call failed\n"); + status = -ENODEV; + goto abort_with_netdev; + } + myri10ge_select_firmware(mgp); + + /* Find the vendor-specific cap so we can check + * the reboot register later on */ + mgp->vendor_specific_offset + = pci_find_capability(pdev, PCI_CAP_ID_VNDR); + + /* Set our max read request to 4KB */ + cap = pci_find_capability(pdev, PCI_CAP_ID_EXP); + if (cap < 64) { + dev_err(&pdev->dev, "Bad PCI_CAP_ID_EXP location %d\n", cap); + goto abort_with_netdev; + } + status = pci_read_config_word(pdev, cap + PCI_EXP_DEVCTL, &val); + if (status != 0) { + dev_err(&pdev->dev, "Error %d reading PCI_EXP_DEVCTL\n", + status); + goto abort_with_netdev; + } + val = (val & ~PCI_EXP_DEVCTL_READRQ) | (5 << 12); + status = pci_write_config_word(pdev, cap + PCI_EXP_DEVCTL, val); + if (status != 0) { + dev_err(&pdev->dev, "Error %d writing PCI_EXP_DEVCTL\n", + status); + goto abort_with_netdev; + } + + pci_set_master(pdev); + dac_enabled = 1; + status = pci_set_dma_mask(pdev, DMA_64BIT_MASK); + if (status != 0) { + dac_enabled = 0; + dev_err(&pdev->dev, + "64-bit pci address mask was refused, trying 32-bit"); + status = pci_set_dma_mask(pdev, DMA_32BIT_MASK); + } + if (status != 0) { + dev_err(&pdev->dev, "Error %d setting DMA mask\n", status); + goto abort_with_netdev; + } + mgp->cmd = pci_alloc_consistent(pdev, sizeof(*mgp->cmd), &mgp->cmd_bus); + if (mgp->cmd == NULL) + goto abort_with_netdev; + + mgp->fw_stats = pci_alloc_consistent(pdev, sizeof(*mgp->fw_stats), + &mgp->fw_stats_bus); + if (mgp->fw_stats == NULL) + goto abort_with_cmd; + + mgp->board_span = pci_resource_len(pdev, 0); + mgp->iomem_base = pci_resource_start(pdev, 0); + mgp->mtrr = -1; +#ifdef CONFIG_MTRR + mgp->mtrr = mtrr_add(mgp->iomem_base, mgp->board_span, + MTRR_TYPE_WRCOMB, 1); +#endif + /* Hack. need to get rid of these magic numbers */ + mgp->sram_size = + 2 * 1024 * 1024 - (2 * (48 * 1024) + (32 * 1024)) - 0x100; + if (mgp->sram_size > mgp->board_span) { + dev_err(&pdev->dev, "board span %ld bytes too small\n", + mgp->board_span); + goto abort_with_wc; + } + mgp->sram = ioremap(mgp->iomem_base, mgp->board_span); + if (mgp->sram == NULL) { + dev_err(&pdev->dev, "ioremap failed for %ld bytes at 0x%lx\n", + mgp->board_span, mgp->iomem_base); + status = -ENXIO; + goto abort_with_wc; + } + memcpy_fromio(mgp->eeprom_strings, + mgp->sram + mgp->sram_size - MYRI10GE_EEPROM_STRINGS_SIZE, + MYRI10GE_EEPROM_STRINGS_SIZE); + memset(mgp->eeprom_strings + MYRI10GE_EEPROM_STRINGS_SIZE - 2, 0, 2); + status = myri10ge_read_mac_addr(mgp); + if (status) + goto abort_with_ioremap; + + for (i = 0; i < ETH_ALEN; i++) + netdev->dev_addr[i] = mgp->mac_addr[i]; + + /* allocate rx done ring */ + bytes = myri10ge_max_intr_slots * sizeof(*mgp->rx_done.entry); + mgp->rx_done.entry = + pci_alloc_consistent(pdev, bytes, &mgp->rx_done.bus); + if (mgp->rx_done.entry == NULL) + goto abort_with_ioremap; + memset(mgp->rx_done.entry, 0, bytes); + + status = myri10ge_load_firmware(mgp); + if (status != 0) { + dev_err(&pdev->dev, "failed to load firmware\n"); + goto abort_with_rx_done; + } + + status = myri10ge_reset(mgp); + if (status != 0) { + dev_err(&pdev->dev, "failed reset\n"); + goto abort_with_firmware; + } + + if (myri10ge_msi) { + status = pci_enable_msi(pdev); + if (status != 0) + dev_err(&pdev->dev, + "Error %d setting up MSI; falling back to xPIC\n", + status); + else + mgp->msi_enabled = 1; + } + + status = request_irq(pdev->irq, myri10ge_intr, SA_SHIRQ, + netdev->name, mgp); + if (status != 0) { + dev_err(&pdev->dev, "failed to allocate IRQ\n"); + goto abort_with_firmware; + } + + pci_set_drvdata(pdev, mgp); + if ((myri10ge_initial_mtu + ETH_HLEN) > MYRI10GE_MAX_ETHER_MTU) + myri10ge_initial_mtu = MYRI10GE_MAX_ETHER_MTU - ETH_HLEN; + if ((myri10ge_initial_mtu + ETH_HLEN) < 68) + myri10ge_initial_mtu = 68; + netdev->mtu = myri10ge_initial_mtu; + netdev->open = myri10ge_open; + netdev->stop = myri10ge_close; + netdev->hard_start_xmit = myri10ge_xmit; + netdev->get_stats = myri10ge_get_stats; + netdev->base_addr = mgp->iomem_base; + netdev->irq = pdev->irq; + netdev->change_mtu = myri10ge_change_mtu; + netdev->set_multicast_list = myri10ge_set_multicast_list; + netdev->set_mac_address = myri10ge_set_mac_address; + netdev->features = NETIF_F_SG | NETIF_F_HW_CSUM | NETIF_F_TSO; + if (dac_enabled) + netdev->features |= NETIF_F_HIGHDMA; + netdev->poll = myri10ge_poll; + netdev->weight = myri10ge_napi_weight; + + /* Save configuration space to be restored if the + * nic resets due to a parity error */ + myri10ge_save_state(mgp); + /* Restore state immediately since pci_save_msi_state disables MSI */ + myri10ge_restore_state(mgp); + + /* Setup the watchdog timer */ + setup_timer(&mgp->watchdog_timer, myri10ge_watchdog_timer, + (unsigned long)mgp); + + SET_ETHTOOL_OPS(netdev, &myri10ge_ethtool_ops); + INIT_WORK(&mgp->watchdog_work, myri10ge_watchdog, mgp); + status = register_netdev(netdev); + if (status != 0) { + dev_err(&pdev->dev, "register_netdev failed: %d\n", status); + goto abort_with_irq; + } + + printk(KERN_INFO "myri10ge: %s: %s IRQ %d, tx bndry %d, fw %s, WC %s\n", + netdev->name, (mgp->msi_enabled ? "MSI" : "xPIC"), + pdev->irq, mgp->tx.boundary, mgp->fw_name, + (mgp->mtrr >= 0 ? "Enabled" : "Disabled")); + + return 0; + +abort_with_irq: + free_irq(pdev->irq, mgp); + if (mgp->msi_enabled) + pci_disable_msi(pdev); + +abort_with_firmware: + myri10ge_dummy_rdma(mgp, 0); + +abort_with_rx_done: + bytes = myri10ge_max_intr_slots * sizeof(*mgp->rx_done.entry); + pci_free_consistent(pdev, bytes, mgp->rx_done.entry, mgp->rx_done.bus); + +abort_with_ioremap: + iounmap(mgp->sram); + +abort_with_wc: +#ifdef CONFIG_MTRR + if (mgp->mtrr >= 0) + mtrr_del(mgp->mtrr, mgp->iomem_base, mgp->board_span); +#endif + pci_free_consistent(pdev, sizeof(*mgp->fw_stats), + mgp->fw_stats, mgp->fw_stats_bus); + +abort_with_cmd: + pci_free_consistent(pdev, sizeof(*mgp->cmd), mgp->cmd, mgp->cmd_bus); + +abort_with_netdev: + + free_netdev(netdev); + return status; +} + +/* + * myri10ge_remove + * + * Does what is necessary to shutdown one Myrinet device. Called + * once for each Myrinet card by the kernel when a module is + * unloaded. + */ +static void myri10ge_remove(struct pci_dev *pdev) +{ + struct myri10ge_priv *mgp; + struct net_device *netdev; + size_t bytes; + + mgp = pci_get_drvdata(pdev); + if (mgp == NULL) + return; + + flush_scheduled_work(); + netdev = mgp->dev; + unregister_netdev(netdev); + free_irq(pdev->irq, mgp); + if (mgp->msi_enabled) + pci_disable_msi(pdev); + + myri10ge_dummy_rdma(mgp, 0); + + bytes = myri10ge_max_intr_slots * sizeof(*mgp->rx_done.entry); + pci_free_consistent(pdev, bytes, mgp->rx_done.entry, mgp->rx_done.bus); + + iounmap(mgp->sram); + +#ifdef CONFIG_MTRR + if (mgp->mtrr >= 0) + mtrr_del(mgp->mtrr, mgp->iomem_base, mgp->board_span); +#endif + pci_free_consistent(pdev, sizeof(*mgp->fw_stats), + mgp->fw_stats, mgp->fw_stats_bus); + + pci_free_consistent(pdev, sizeof(*mgp->cmd), mgp->cmd, mgp->cmd_bus); + + free_netdev(netdev); + pci_set_drvdata(pdev, NULL); +} + +#define PCI_DEVICE_ID_MYIRCOM_MYRI10GE_Z8E 0x0008 + +static struct pci_device_id myri10ge_pci_tbl[] = { + {PCI_DEVICE(PCI_VENDOR_ID_MYRICOM, PCI_DEVICE_ID_MYIRCOM_MYRI10GE_Z8E)}, + {0}, +}; + +static struct pci_driver myri10ge_driver = { + .name = "myri10ge", + .probe = myri10ge_probe, + .remove = myri10ge_remove, + .id_table = myri10ge_pci_tbl, +#ifdef CONFIG_PM + .suspend = myri10ge_suspend, + .resume = myri10ge_resume, +#endif +}; + +static __init int myri10ge_init_module(void) +{ + printk(KERN_INFO "%s: Version %s\n", myri10ge_driver.name, + MYRI10GE_VERSION_STR); + return pci_register_driver(&myri10ge_driver); +} + +module_init(myri10ge_init_module); + +static __exit void myri10ge_cleanup_module(void) +{ + pci_unregister_driver(&myri10ge_driver); +} + +module_exit(myri10ge_cleanup_module); diff --git a/drivers/net/myri10ge/myri10ge_mcp.h b/drivers/net/myri10ge/myri10ge_mcp.h new file mode 100644 index 0000000000..ac23e18db6 --- /dev/null +++ b/drivers/net/myri10ge/myri10ge_mcp.h @@ -0,0 +1,205 @@ +#ifndef __MYRI10GE_MCP_H__ +#define __MYRI10GE_MCP_H__ + +#define MXGEFW_VERSION_MAJOR 1 +#define MXGEFW_VERSION_MINOR 4 + +/* 8 Bytes */ +struct mcp_dma_addr { + u32 high; + u32 low; +}; + +/* 4 Bytes */ +struct mcp_slot { + u16 checksum; + u16 length; +}; + +/* 64 Bytes */ +struct mcp_cmd { + u32 cmd; + u32 data0; /* will be low portion if data > 32 bits */ + /* 8 */ + u32 data1; /* will be high portion if data > 32 bits */ + u32 data2; /* currently unused.. */ + /* 16 */ + struct mcp_dma_addr response_addr; + /* 24 */ + u8 pad[40]; +}; + +/* 8 Bytes */ +struct mcp_cmd_response { + u32 data; + u32 result; +}; + +/* + * flags used in mcp_kreq_ether_send_t: + * + * The SMALL flag is only needed in the first segment. It is raised + * for packets that are total less or equal 512 bytes. + * + * The CKSUM flag must be set in all segments. + * + * The PADDED flags is set if the packet needs to be padded, and it + * must be set for all segments. + * + * The MXGEFW_FLAGS_ALIGN_ODD must be set if the cumulative + * length of all previous segments was odd. + */ + +#define MXGEFW_FLAGS_SMALL 0x1 +#define MXGEFW_FLAGS_TSO_HDR 0x1 +#define MXGEFW_FLAGS_FIRST 0x2 +#define MXGEFW_FLAGS_ALIGN_ODD 0x4 +#define MXGEFW_FLAGS_CKSUM 0x8 +#define MXGEFW_FLAGS_TSO_LAST 0x8 +#define MXGEFW_FLAGS_NO_TSO 0x10 +#define MXGEFW_FLAGS_TSO_CHOP 0x10 +#define MXGEFW_FLAGS_TSO_PLD 0x20 + +#define MXGEFW_SEND_SMALL_SIZE 1520 +#define MXGEFW_MAX_MTU 9400 + +union mcp_pso_or_cumlen { + u16 pseudo_hdr_offset; + u16 cum_len; +}; + +#define MXGEFW_MAX_SEND_DESC 12 +#define MXGEFW_PAD 2 + +/* 16 Bytes */ +struct mcp_kreq_ether_send { + u32 addr_high; + u32 addr_low; + u16 pseudo_hdr_offset; + u16 length; + u8 pad; + u8 rdma_count; + u8 cksum_offset; /* where to start computing cksum */ + u8 flags; /* as defined above */ +}; + +/* 8 Bytes */ +struct mcp_kreq_ether_recv { + u32 addr_high; + u32 addr_low; +}; + +/* Commands */ + +#define MXGEFW_CMD_OFFSET 0xf80000 + +enum myri10ge_mcp_cmd_type { + MXGEFW_CMD_NONE = 0, + /* Reset the mcp, it is left in a safe state, waiting + * for the driver to set all its parameters */ + MXGEFW_CMD_RESET, + + /* get the version number of the current firmware.. + * (may be available in the eeprom strings..? */ + MXGEFW_GET_MCP_VERSION, + + /* Parameters which must be set by the driver before it can + * issue MXGEFW_CMD_ETHERNET_UP. They persist until the next + * MXGEFW_CMD_RESET is issued */ + + MXGEFW_CMD_SET_INTRQ_DMA, + MXGEFW_CMD_SET_BIG_BUFFER_SIZE, /* in bytes, power of 2 */ + MXGEFW_CMD_SET_SMALL_BUFFER_SIZE, /* in bytes */ + + /* Parameters which refer to lanai SRAM addresses where the + * driver must issue PIO writes for various things */ + + MXGEFW_CMD_GET_SEND_OFFSET, + MXGEFW_CMD_GET_SMALL_RX_OFFSET, + MXGEFW_CMD_GET_BIG_RX_OFFSET, + MXGEFW_CMD_GET_IRQ_ACK_OFFSET, + MXGEFW_CMD_GET_IRQ_DEASSERT_OFFSET, + + /* Parameters which refer to rings stored on the MCP, + * and whose size is controlled by the mcp */ + + MXGEFW_CMD_GET_SEND_RING_SIZE, /* in bytes */ + MXGEFW_CMD_GET_RX_RING_SIZE, /* in bytes */ + + /* Parameters which refer to rings stored in the host, + * and whose size is controlled by the host. Note that + * all must be physically contiguous and must contain + * a power of 2 number of entries. */ + + MXGEFW_CMD_SET_INTRQ_SIZE, /* in bytes */ + + /* command to bring ethernet interface up. Above parameters + * (plus mtu & mac address) must have been exchanged prior + * to issuing this command */ + MXGEFW_CMD_ETHERNET_UP, + + /* command to bring ethernet interface down. No further sends + * or receives may be processed until an MXGEFW_CMD_ETHERNET_UP + * is issued, and all interrupt queues must be flushed prior + * to ack'ing this command */ + + MXGEFW_CMD_ETHERNET_DOWN, + + /* commands the driver may issue live, without resetting + * the nic. Note that increasing the mtu "live" should + * only be done if the driver has already supplied buffers + * sufficiently large to handle the new mtu. Decreasing + * the mtu live is safe */ + + MXGEFW_CMD_SET_MTU, + MXGEFW_CMD_GET_INTR_COAL_DELAY_OFFSET, /* in microseconds */ + MXGEFW_CMD_SET_STATS_INTERVAL, /* in microseconds */ + MXGEFW_CMD_SET_STATS_DMA, + + MXGEFW_ENABLE_PROMISC, + MXGEFW_DISABLE_PROMISC, + MXGEFW_SET_MAC_ADDRESS, + + MXGEFW_ENABLE_FLOW_CONTROL, + MXGEFW_DISABLE_FLOW_CONTROL, + + /* do a DMA test + * data0,data1 = DMA address + * data2 = RDMA length (MSH), WDMA length (LSH) + * command return data = repetitions (MSH), 0.5-ms ticks (LSH) + */ + MXGEFW_DMA_TEST +}; + +enum myri10ge_mcp_cmd_status { + MXGEFW_CMD_OK = 0, + MXGEFW_CMD_UNKNOWN, + MXGEFW_CMD_ERROR_RANGE, + MXGEFW_CMD_ERROR_BUSY, + MXGEFW_CMD_ERROR_EMPTY, + MXGEFW_CMD_ERROR_CLOSED, + MXGEFW_CMD_ERROR_HASH_ERROR, + MXGEFW_CMD_ERROR_BAD_PORT, + MXGEFW_CMD_ERROR_RESOURCES +}; + +/* 40 Bytes */ +struct mcp_irq_data { + u32 send_done_count; + + u32 link_up; + u32 dropped_link_overflow; + u32 dropped_link_error_or_filtered; + u32 dropped_runt; + u32 dropped_overrun; + u32 dropped_no_small_buffer; + u32 dropped_no_big_buffer; + u32 rdma_tags_available; + + u8 tx_stopped; + u8 link_down; + u8 stats_updated; + u8 valid; +}; + +#endif /* __MYRI10GE_MCP_H__ */ diff --git a/drivers/net/myri10ge/myri10ge_mcp_gen_header.h b/drivers/net/myri10ge/myri10ge_mcp_gen_header.h new file mode 100644 index 0000000000..1d3a35f107 --- /dev/null +++ b/drivers/net/myri10ge/myri10ge_mcp_gen_header.h @@ -0,0 +1,58 @@ +#ifndef __MYRI10GE_MCP_GEN_HEADER_H__ +#define __MYRI10GE_MCP_GEN_HEADER_H__ + +/* this file define a standard header used as a first entry point to + * exchange information between firmware/driver and driver. The + * header structure can be anywhere in the mcp. It will usually be in + * the .data section, because some fields needs to be initialized at + * compile time. + * The 32bit word at offset MX_HEADER_PTR_OFFSET in the mcp must + * contains the location of the header. + * + * Typically a MCP will start with the following: + * .text + * .space 52 ! to help catch MEMORY_INT errors + * bt start ! jump to real code + * nop + * .long _gen_mcp_header + * + * The source will have a definition like: + * + * mcp_gen_header_t gen_mcp_header = { + * .header_length = sizeof(mcp_gen_header_t), + * .mcp_type = MCP_TYPE_XXX, + * .version = "something $Id: mcp_gen_header.h,v 1.2 2006/05/13 10:04:35 bgoglin Exp $", + * .mcp_globals = (unsigned)&Globals + * }; + */ + +#define MCP_HEADER_PTR_OFFSET 0x3c + +#define MCP_TYPE_MX 0x4d582020 /* "MX " */ +#define MCP_TYPE_PCIE 0x70636965 /* "PCIE" pcie-only MCP */ +#define MCP_TYPE_ETH 0x45544820 /* "ETH " */ +#define MCP_TYPE_MCP0 0x4d435030 /* "MCP0" */ + +struct mcp_gen_header { + /* the first 4 fields are filled at compile time */ + unsigned header_length; + unsigned mcp_type; + char version[128]; + unsigned mcp_globals; /* pointer to mcp-type specific structure */ + + /* filled by the MCP at run-time */ + unsigned sram_size; + unsigned string_specs; /* either the original STRING_SPECS or a superset */ + unsigned string_specs_len; + + /* Fields above this comment are guaranteed to be present. + * + * Fields below this comment are extensions added in later versions + * of this struct, drivers should compare the header_length against + * offsetof(field) to check wether a given MCP implements them. + * + * Never remove any field. Keep everything naturally align. + */ +}; + +#endif /* __MYRI10GE_MCP_GEN_HEADER_H__ */ diff --git a/include/linux/pci_ids.h b/include/linux/pci_ids.h index 563eeadbea..151549a69e 100644 --- a/include/linux/pci_ids.h +++ b/include/linux/pci_ids.h @@ -1827,6 +1827,7 @@ #define PCI_VENDOR_ID_SAMSUNG 0x144d +#define PCI_VENDOR_ID_MYRICOM 0x14c1 #define PCI_VENDOR_ID_TITAN 0x14D2 #define PCI_DEVICE_ID_TITAN_010L 0x8001