From: Linus Walleij Date: Fri, 14 Apr 2006 23:03:33 +0000 (-0700) Subject: [IRDA]: smsc-ircc2, smcinit support for ALi ISA bridges X-Git-Tag: v2.6.17-rc2~28^2~1 X-Git-Url: https://err.no/cgi-bin/gitweb.cgi?a=commitdiff_plain;h=08d099974a09faf4cb11ffc46da87073fa132fc0;p=linux-2.6 [IRDA]: smsc-ircc2, smcinit support for ALi ISA bridges From: Linus Walleij This patch enables support for ALi ISA bridges when we run the smcinit code. It is needed to properly configure some Toshiba laptops. Signed-off-by: Samuel Ortiz Signed-off-by: David S. Miller --- diff --git a/drivers/net/irda/smsc-ircc2.c b/drivers/net/irda/smsc-ircc2.c index bbcfc8ec35..58f76cefbc 100644 --- a/drivers/net/irda/smsc-ircc2.c +++ b/drivers/net/irda/smsc-ircc2.c @@ -225,6 +225,8 @@ static int __init smsc_superio_lpc(unsigned short cfg_base); #ifdef CONFIG_PCI static int __init preconfigure_smsc_chip(struct smsc_ircc_subsystem_configuration *conf); static int __init preconfigure_through_82801(struct pci_dev *dev, struct smsc_ircc_subsystem_configuration *conf); +static void __init preconfigure_ali_port(struct pci_dev *dev, + unsigned short port); static int __init preconfigure_through_ali(struct pci_dev *dev, struct smsc_ircc_subsystem_configuration *conf); static int __init smsc_ircc_preconfigure_subsystems(unsigned short ircc_cfg, unsigned short ircc_fir, @@ -2327,9 +2329,14 @@ static int __init smsc_superio_lpc(unsigned short cfg_base) * pre-configuration not properly done by the BIOS (especially laptops) * This code is based in part on smcinit.c, tosh1800-smcinit.c * and tosh2450-smcinit.c. The table lists the device entries - * for ISA bridges with an LPC (Local Peripheral Configurator) - * that are in turn used to configure the SMSC device with default - * SIR and FIR I/O ports, DMA and IRQ. + * for ISA bridges with an LPC (Low Pin Count) controller which + * handles the communication with the SMSC device. After the LPC + * controller is initialized through PCI, the SMSC device is initialized + * through a dedicated port in the ISA port-mapped I/O area, this latter + * area is used to configure the SMSC device with default + * SIR and FIR I/O ports, DMA and IRQ. Different vendors have + * used different sets of parameters and different control port + * addresses making a subsystem device table necessary. */ #ifdef CONFIG_PCI #define PCIID_VENDOR_INTEL 0x8086 @@ -2340,9 +2347,10 @@ static struct smsc_ircc_subsystem_configuration subsystem_configurations[] __dev .device = 0x24cc, .subvendor = 0x103c, .subdevice = 0x088c, - .sir_io = 0x02f8, /* Quite certain these are the same for nc8000 as for nc6000 */ + /* Quite certain these are the same for nc8000 as for nc6000 */ + .sir_io = 0x02f8, .fir_io = 0x0130, - .fir_irq = 0x09, + .fir_irq = 0x05, .fir_dma = 0x03, .cfg_base = 0x004e, .preconfigure = preconfigure_through_82801, @@ -2355,60 +2363,79 @@ static struct smsc_ircc_subsystem_configuration subsystem_configurations[] __dev .subdevice = 0x0890, .sir_io = 0x02f8, .fir_io = 0x0130, - .fir_irq = 0x09, + .fir_irq = 0x05, .fir_dma = 0x03, .cfg_base = 0x004e, .preconfigure = preconfigure_through_82801, .name = "HP nc6000", }, { - .vendor = PCIID_VENDOR_INTEL, /* Intel 82801DB/DBL (ICH4/ICH4-L) LPC Interface Bridge */ + /* Intel 82801DB/DBL (ICH4/ICH4-L) LPC Interface Bridge */ + .vendor = PCIID_VENDOR_INTEL, .device = 0x24c0, .subvendor = 0x1179, - .subdevice = 0xffff, /* 0xffff is "any", Not sure, 0x0001 or 0x0002 */ + .subdevice = 0xffff, /* 0xffff is "any" */ .sir_io = 0x03f8, .fir_io = 0x0130, .fir_irq = 0x07, .fir_dma = 0x01, .cfg_base = 0x002e, .preconfigure = preconfigure_through_82801, - .name = "Toshiba Satellite 2450", + .name = "Toshiba laptop with Intel 82801DB/DBL LPC bridge", }, { .vendor = PCIID_VENDOR_INTEL, /* Intel 82801CAM ISA bridge */ - .device = 0x248c, /* Some use 24cc? */ + .device = 0x248c, .subvendor = 0x1179, - .subdevice = 0xffff, /* 0xffff is "any", Not sure, 0x0001 or 0x0002 */ + .subdevice = 0xffff, /* 0xffff is "any" */ .sir_io = 0x03f8, .fir_io = 0x0130, .fir_irq = 0x03, .fir_dma = 0x03, .cfg_base = 0x002e, .preconfigure = preconfigure_through_82801, - .name = "Toshiba Satellite 5100/5200, Tecra 9100", + .name = "Toshiba laptop with Intel 82801CAM ISA bridge", }, { - .vendor = PCIID_VENDOR_ALI, /* ALi M1533/M1535 PCI to ISA Bridge [Aladdin IV/V/V+] */ + /* 82801DBM (ICH4-M) LPC Interface Bridge */ + .vendor = PCIID_VENDOR_INTEL, + .device = 0x24cc, + .subvendor = 0x1179, + .subdevice = 0xffff, /* 0xffff is "any" */ + .sir_io = 0x03f8, + .fir_io = 0x0130, + .fir_irq = 0x03, + .fir_dma = 0x03, + .cfg_base = 0x002e, + .preconfigure = preconfigure_through_82801, + .name = "Toshiba laptop with Intel 8281DBM LPC bridge", + }, + { + /* ALi M1533/M1535 PCI to ISA Bridge [Aladdin IV/V/V+] */ + .vendor = PCIID_VENDOR_ALI, .device = 0x1533, .subvendor = 0x1179, - .subdevice = 0xffff, /* 0xffff is "any", Not sure, 0x0001 or 0x0002 */ + .subdevice = 0xffff, /* 0xffff is "any" */ .sir_io = 0x02e8, .fir_io = 0x02f8, .fir_irq = 0x07, .fir_dma = 0x03, .cfg_base = 0x002e, .preconfigure = preconfigure_through_ali, - .name = "Toshiba Satellite 1800", + .name = "Toshiba laptop with ALi ISA bridge", }, { } // Terminator }; /* - * This sets up the basic SMSC parameters (FIR port, SIR port, FIR DMA, FIR IRQ) + * This sets up the basic SMSC parameters + * (FIR port, SIR port, FIR DMA, FIR IRQ) * through the chip configuration port. */ -static int __init preconfigure_smsc_chip(struct smsc_ircc_subsystem_configuration *conf) +static int __init preconfigure_smsc_chip(struct + smsc_ircc_subsystem_configuration + *conf) { unsigned short iobase = conf->cfg_base; unsigned char tmpbyte; @@ -2416,7 +2443,9 @@ static int __init preconfigure_smsc_chip(struct smsc_ircc_subsystem_configuratio outb(LPC47N227_CFGACCESSKEY, iobase); // enter configuration state outb(SMSCSIOFLAT_DEVICEID_REG, iobase); // set for device ID tmpbyte = inb(iobase +1); // Read device ID - IRDA_DEBUG(0, "Detected Chip id: 0x%02x, setting up registers...\n",tmpbyte); + IRDA_DEBUG(0, + "Detected Chip id: 0x%02x, setting up registers...\n", + tmpbyte); /* Disable UART1 and set up SIR I/O port */ outb(0x24, iobase); // select CR24 - UART1 base addr @@ -2426,6 +2455,7 @@ static int __init preconfigure_smsc_chip(struct smsc_ircc_subsystem_configuratio tmpbyte = inb(iobase + 1); if (tmpbyte != (conf->sir_io >> 2) ) { IRDA_WARNING("ERROR: could not configure SIR ioport.\n"); + IRDA_WARNING("Try to supply ircc_cfg argument.\n"); return -ENXIO; } @@ -2461,7 +2491,8 @@ static int __init preconfigure_smsc_chip(struct smsc_ircc_subsystem_configuratio outb(SMSCSIOFLAT_UARTMODE0C_REG, iobase); // CR0C - UART mode tmpbyte = inb(iobase + 1); - tmpbyte &= ~SMSCSIOFLAT_UART2MODE_MASK | SMSCSIOFLAT_UART2MODE_VAL_IRDA; + tmpbyte &= ~SMSCSIOFLAT_UART2MODE_MASK | + SMSCSIOFLAT_UART2MODE_VAL_IRDA; outb(tmpbyte, iobase + 1); // enable IrDA (HPSIR) mode, high speed outb(LPC47N227_APMBOOTDRIVE_REG, iobase); // CR07 - Auto Pwr Mgt/boot drive sel @@ -2486,53 +2517,226 @@ static int __init preconfigure_smsc_chip(struct smsc_ircc_subsystem_configuratio return 0; } -/* 82801CAM registers */ +/* 82801CAM generic registers */ #define VID 0x00 #define DID 0x02 -#define PIRQA_ROUT 0x60 +#define PIRQ_A_D_ROUT 0x60 +#define SIRQ_CNTL 0x64 +#define PIRQ_E_H_ROUT 0x68 #define PCI_DMA_C 0x90 +/* LPC-specific registers */ #define COM_DEC 0xe0 +#define GEN1_DEC 0xe4 #define LPC_EN 0xe6 #define GEN2_DEC 0xec /* - * Sets up the I/O range using the 82801CAM ISA bridge, 82801DBM LPC bridge or - * Intel 82801DB/DBL (ICH4/ICH4-L) LPC Interface Bridge. They all work the same way! + * Sets up the I/O range using the 82801CAM ISA bridge, 82801DBM LPC bridge + * or Intel 82801DB/DBL (ICH4/ICH4-L) LPC Interface Bridge. + * They all work the same way! */ static int __init preconfigure_through_82801(struct pci_dev *dev, - struct smsc_ircc_subsystem_configuration *conf) + struct + smsc_ircc_subsystem_configuration + *conf) { unsigned short tmpword; - int ret; + unsigned char tmpbyte; - IRDA_MESSAGE("Setting up the SMSC device via the 82801 controller.\n"); - pci_write_config_byte(dev, COM_DEC, 0x10); + IRDA_MESSAGE("Setting up Intel 82801 controller and SMSC device\n"); + /* + * Select the range for the COMA COM port (SIR) + * Register COM_DEC: + * Bit 7: reserved + * Bit 6-4, COMB decode range + * Bit 3: reserved + * Bit 2-0, COMA decode range + * + * Decode ranges: + * 000 = 0x3f8-0x3ff (COM1) + * 001 = 0x2f8-0x2ff (COM2) + * 010 = 0x220-0x227 + * 011 = 0x228-0x22f + * 100 = 0x238-0x23f + * 101 = 0x2e8-0x2ef (COM4) + * 110 = 0x338-0x33f + * 111 = 0x3e8-0x3ef (COM3) + */ + pci_read_config_byte(dev, COM_DEC, &tmpbyte); + tmpbyte &= 0xf8; /* mask COMA bits */ + switch(conf->sir_io) { + case 0x3f8: + tmpbyte |= 0x00; + break; + case 0x2f8: + tmpbyte |= 0x01; + break; + case 0x220: + tmpbyte |= 0x02; + break; + case 0x228: + tmpbyte |= 0x03; + break; + case 0x238: + tmpbyte |= 0x04; + break; + case 0x2e8: + tmpbyte |= 0x05; + break; + case 0x338: + tmpbyte |= 0x06; + break; + case 0x3e8: + tmpbyte |= 0x07; + break; + default: + tmpbyte |= 0x01; /* COM2 default */ + } + IRDA_DEBUG(1, "COM_DEC (write): 0x%02x\n", tmpbyte); + pci_write_config_byte(dev, COM_DEC, tmpbyte); - /* Enable LPC */ - pci_read_config_word(dev, LPC_EN, &tmpword); /* LPC_EN register */ - tmpword &= 0xfffd; /* mask bit 1 */ - tmpword |= 0x0001; /* set bit 0 : COMA addr range enable */ + /* Enable Low Pin Count interface */ + pci_read_config_word(dev, LPC_EN, &tmpword); + /* These seem to be set up at all times, + * just make sure it is properly set. + */ + switch(conf->cfg_base) { + case 0x04e: + tmpword |= 0x2000; + break; + case 0x02e: + tmpword |= 0x1000; + break; + case 0x062: + tmpword |= 0x0800; + break; + case 0x060: + tmpword |= 0x0400; + break; + default: + IRDA_WARNING("Uncommon I/O base address: 0x%04x\n", + conf->cfg_base); + break; + } + tmpword &= 0xfffd; /* disable LPC COMB */ + tmpword |= 0x0001; /* set bit 0 : enable LPC COMA addr range (GEN2) */ + IRDA_DEBUG(1, "LPC_EN (write): 0x%04x\n", tmpword); pci_write_config_word(dev, LPC_EN, tmpword); - /* Setup DMA */ - pci_write_config_word(dev, PCI_DMA_C, 0xc0c0); /* LPC I/F DMA on, channel 3 -- rtm (?? PCI DMA ?) */ - pci_write_config_word(dev, GEN2_DEC, 0x131); /* LPC I/F 2nd decode range */ + /* + * Configure LPC DMA channel + * PCI_DMA_C bits: + * Bit 15-14: DMA channel 7 select + * Bit 13-12: DMA channel 6 select + * Bit 11-10: DMA channel 5 select + * Bit 9-8: Reserved + * Bit 7-6: DMA channel 3 select + * Bit 5-4: DMA channel 2 select + * Bit 3-2: DMA channel 1 select + * Bit 1-0: DMA channel 0 select + * 00 = Reserved value + * 01 = PC/PCI DMA + * 10 = Reserved value + * 11 = LPC I/F DMA + */ + pci_read_config_word(dev, PCI_DMA_C, &tmpword); + switch(conf->fir_dma) { + case 0x07: + tmpword |= 0xc000; + break; + case 0x06: + tmpword |= 0x3000; + break; + case 0x05: + tmpword |= 0x0c00; + break; + case 0x03: + tmpword |= 0x00c0; + break; + case 0x02: + tmpword |= 0x0030; + break; + case 0x01: + tmpword |= 0x000c; + break; + case 0x00: + tmpword |= 0x0003; + break; + default: + break; /* do not change settings */ + } + IRDA_DEBUG(1, "PCI_DMA_C (write): 0x%04x\n", tmpword); + pci_write_config_word(dev, PCI_DMA_C, tmpword); + + /* + * GEN2_DEC bits: + * Bit 15-4: Generic I/O range + * Bit 3-1: reserved (read as 0) + * Bit 0: enable GEN2 range on LPC I/F + */ + tmpword = conf->fir_io & 0xfff8; + tmpword |= 0x0001; + IRDA_DEBUG(1, "GEN2_DEC (write): 0x%04x\n", tmpword); + pci_write_config_word(dev, GEN2_DEC, tmpword); /* Pre-configure chip */ - ret = preconfigure_smsc_chip(conf); + return preconfigure_smsc_chip(conf); +} - /* Disable LPC */ - pci_read_config_word(dev, LPC_EN, &tmpword); /* LPC_EN register */ - tmpword &= 0xfffc; /* mask bit 1 and bit 0, COMA addr range disable */ - pci_write_config_word(dev, LPC_EN, tmpword); - return ret; +/* + * Pre-configure a certain port on the ALi 1533 bridge. + * This is based on reverse-engineering since ALi does not + * provide any data sheet for the 1533 chip. + */ +static void __init preconfigure_ali_port(struct pci_dev *dev, + unsigned short port) +{ + unsigned char reg; + /* These bits obviously control the different ports */ + unsigned char mask; + unsigned char tmpbyte; + + switch(port) { + case 0x0130: + case 0x0178: + reg = 0xb0; + mask = 0x80; + break; + case 0x03f8: + reg = 0xb4; + mask = 0x80; + break; + case 0x02f8: + reg = 0xb4; + mask = 0x30; + break; + case 0x02e8: + reg = 0xb4; + mask = 0x08; + break; + default: + IRDA_ERROR("Failed to configure unsupported port on ALi 1533 bridge: 0x%04x\n", port); + return; + } + + pci_read_config_byte(dev, reg, &tmpbyte); + /* Turn on the right bits */ + tmpbyte |= mask; + pci_write_config_byte(dev, reg, tmpbyte); + IRDA_MESSAGE("Activated ALi 1533 ISA bridge port 0x%04x.\n", port); + return; } static int __init preconfigure_through_ali(struct pci_dev *dev, - struct smsc_ircc_subsystem_configuration *conf) + struct + smsc_ircc_subsystem_configuration + *conf) { - /* TODO: put in ALi 1533 configuration here. */ - IRDA_MESSAGE("SORRY: %s has an unsupported bridge controller (ALi): not pre-configured.\n", conf->name); - return -ENODEV; + /* Configure the two ports on the ALi 1533 */ + preconfigure_ali_port(dev, conf->sir_io); + preconfigure_ali_port(dev, conf->fir_io); + + /* Pre-configure chip */ + return preconfigure_smsc_chip(conf); } static int __init smsc_ircc_preconfigure_subsystems(unsigned short ircc_cfg, @@ -2552,9 +2756,10 @@ static int __init smsc_ircc_preconfigure_subsystems(unsigned short ircc_cfg, struct smsc_ircc_subsystem_configuration *conf; /* - * Cache the subsystem vendor/device: some manufacturers fail to set - * this for all components, so we save it in case there is just - * 0x0000 0x0000 on the device we want to check. + * Cache the subsystem vendor/device: + * some manufacturers fail to set this for all components, + * so we save it in case there is just 0x0000 0x0000 on the + * device we want to check. */ if (dev->subsystem_vendor != 0x0000U) { ss_vendor = dev->subsystem_vendor; @@ -2564,13 +2769,20 @@ static int __init smsc_ircc_preconfigure_subsystems(unsigned short ircc_cfg, for( ; conf->subvendor; conf++) { if(conf->vendor == dev->vendor && conf->device == dev->device && - conf->subvendor == ss_vendor && /* Sometimes these are cached values */ - (conf->subdevice == ss_device || conf->subdevice == 0xffff)) { - struct smsc_ircc_subsystem_configuration tmpconf; + conf->subvendor == ss_vendor && + /* Sometimes these are cached values */ + (conf->subdevice == ss_device || + conf->subdevice == 0xffff)) { + struct smsc_ircc_subsystem_configuration + tmpconf; - memcpy(&tmpconf, conf, sizeof(struct smsc_ircc_subsystem_configuration)); + memcpy(&tmpconf, conf, + sizeof(struct smsc_ircc_subsystem_configuration)); - /* Override the default values with anything passed in as parameter */ + /* + * Override the default values with anything + * passed in as parameter + */ if (ircc_cfg != 0) tmpconf.cfg_base = ircc_cfg; if (ircc_fir != 0)