This option enables support for MIPS Technologies MIPSsim software
emulator.
-config DDB5477
- bool "NEC DDB Vrc-5477"
- select DDB5XXX_COMMON
- select DMA_NONCOHERENT
- select HW_HAS_PCI
- select I8259
- select IRQ_CPU
- select SYS_HAS_CPU_R5432
- select SYS_SUPPORTS_32BIT_KERNEL
- select SYS_SUPPORTS_64BIT_KERNEL if EXPERIMENTAL
- select SYS_SUPPORTS_KGDB
- select SYS_SUPPORTS_KGDB
- select SYS_SUPPORTS_LITTLE_ENDIAN
- help
- This enables support for the R5432-based NEC DDB Vrc-5477,
- or Rockhopper/SolutionGear boards with R5432/R5500 CPUs.
-
- Features : kernel debugging, serial terminal, NFS root fs, on-board
- ether port USB, AC97, PCI, etc.
-
config MARKEINS
bool "NEC EMMA2RH Mark-eins"
select DMA_NONCOHERENT
endchoice
source "arch/mips/au1000/Kconfig"
-source "arch/mips/ddb5xxx/Kconfig"
source "arch/mips/jazz/Kconfig"
source "arch/mips/pmc-sierra/Kconfig"
source "arch/mips/sgi-ip27/Kconfig"
config IRQ_MSP_CIC
bool
-config DDB5XXX_COMMON
- bool
- select SYS_SUPPORTS_KGDB
-
config MIPS_BOARDS_GEN
bool
cflags-$(CONFIG_BASLER_EXCITE) += -Iinclude/asm-mips/mach-excite
load-$(CONFIG_BASLER_EXCITE) += 0x80100000
-#
-# NEC DDB
-#
-core-$(CONFIG_DDB5XXX_COMMON) += arch/mips/ddb5xxx/common/
-
-#
-# NEC DDB Vrc-5477
-#
-core-$(CONFIG_DDB5477) += arch/mips/ddb5xxx/ddb5477/
-load-$(CONFIG_DDB5477) += 0xffffffff80100000
-
#
# Common VR41xx
#
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
-# CONFIG_DDB5477 is not set
# CONFIG_MACH_VR41XX is not set
# CONFIG_PMC_YOSEMITE is not set
# CONFIG_QEMU is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
-# CONFIG_DDB5477 is not set
# CONFIG_MACH_VR41XX is not set
# CONFIG_PMC_YOSEMITE is not set
# CONFIG_QEMU is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
-# CONFIG_DDB5477 is not set
CONFIG_MACH_VR41XX=y
# CONFIG_PMC_YOSEMITE is not set
# CONFIG_QEMU is not set
# CONFIG_MIPS_SIM is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
-# CONFIG_DDB5477 is not set
# CONFIG_MACH_VR41XX is not set
# CONFIG_PMC_YOSEMITE is not set
# CONFIG_QEMU is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
-# CONFIG_DDB5477 is not set
# CONFIG_MACH_VR41XX is not set
# CONFIG_PMC_YOSEMITE is not set
# CONFIG_QEMU is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
-# CONFIG_DDB5477 is not set
# CONFIG_MACH_VR41XX is not set
# CONFIG_PMC_YOSEMITE is not set
# CONFIG_QEMU is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
-# CONFIG_DDB5477 is not set
# CONFIG_MACH_VR41XX is not set
# CONFIG_PMC_YOSEMITE is not set
# CONFIG_QEMU is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
-# CONFIG_DDB5477 is not set
# CONFIG_MACH_VR41XX is not set
# CONFIG_PMC_YOSEMITE is not set
# CONFIG_QEMU is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
-# CONFIG_DDB5477 is not set
# CONFIG_MACH_VR41XX is not set
# CONFIG_PMC_YOSEMITE is not set
# CONFIG_QEMU is not set
+++ /dev/null
-#
-# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.20
-# Tue Feb 20 21:47:28 2007
-#
-CONFIG_MIPS=y
-
-#
-# Machine selection
-#
-CONFIG_ZONE_DMA=y
-# CONFIG_MIPS_MTX1 is not set
-# CONFIG_MIPS_BOSPORUS is not set
-# CONFIG_MIPS_PB1000 is not set
-# CONFIG_MIPS_PB1100 is not set
-# CONFIG_MIPS_PB1500 is not set
-# CONFIG_MIPS_PB1550 is not set
-# CONFIG_MIPS_PB1200 is not set
-# CONFIG_MIPS_DB1000 is not set
-# CONFIG_MIPS_DB1100 is not set
-# CONFIG_MIPS_DB1500 is not set
-# CONFIG_MIPS_DB1550 is not set
-# CONFIG_MIPS_DB1200 is not set
-# CONFIG_MIPS_MIRAGE is not set
-# CONFIG_BASLER_EXCITE is not set
-# CONFIG_MIPS_COBALT is not set
-# CONFIG_MACH_DECSTATION is not set
-# CONFIG_MACH_JAZZ is not set
-# CONFIG_MIPS_ATLAS is not set
-# CONFIG_MIPS_MALTA is not set
-# CONFIG_MIPS_SEAD is not set
-# CONFIG_WR_PPMC is not set
-# CONFIG_MIPS_SIM is not set
-# CONFIG_MOMENCO_JAGUAR_ATX is not set
-# CONFIG_MIPS_XXS1500 is not set
-# CONFIG_PNX8550_JBS is not set
-# CONFIG_PNX8550_STB810 is not set
-CONFIG_DDB5477=y
-# CONFIG_MACH_VR41XX is not set
-# CONFIG_PMC_YOSEMITE is not set
-# CONFIG_QEMU is not set
-# CONFIG_MARKEINS is not set
-# CONFIG_SGI_IP22 is not set
-# CONFIG_SGI_IP27 is not set
-# CONFIG_SGI_IP32 is not set
-# CONFIG_SIBYTE_BIGSUR is not set
-# CONFIG_SIBYTE_SWARM is not set
-# CONFIG_SIBYTE_SENTOSA is not set
-# CONFIG_SIBYTE_RHONE is not set
-# CONFIG_SIBYTE_CARMEL is not set
-# CONFIG_SIBYTE_PTSWARM is not set
-# CONFIG_SIBYTE_LITTLESUR is not set
-# CONFIG_SIBYTE_CRHINE is not set
-# CONFIG_SIBYTE_CRHONE is not set
-# CONFIG_SNI_RM is not set
-# CONFIG_TOSHIBA_JMR3927 is not set
-# CONFIG_TOSHIBA_RBTX4927 is not set
-# CONFIG_TOSHIBA_RBTX4938 is not set
-CONFIG_DDB5477_BUS_FREQUENCY=0
-CONFIG_RWSEM_GENERIC_SPINLOCK=y
-# CONFIG_ARCH_HAS_ILOG2_U32 is not set
-# CONFIG_ARCH_HAS_ILOG2_U64 is not set
-CONFIG_GENERIC_FIND_NEXT_BIT=y
-CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
-CONFIG_GENERIC_TIME=y
-CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
-# CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ is not set
-CONFIG_DMA_NONCOHERENT=y
-CONFIG_DMA_NEED_PCI_MAP_STATE=y
-CONFIG_I8259=y
-# CONFIG_CPU_BIG_ENDIAN is not set
-CONFIG_CPU_LITTLE_ENDIAN=y
-CONFIG_SYS_SUPPORTS_LITTLE_ENDIAN=y
-CONFIG_IRQ_CPU=y
-CONFIG_DDB5XXX_COMMON=y
-CONFIG_MIPS_L1_CACHE_SHIFT=5
-
-#
-# CPU selection
-#
-# CONFIG_CPU_MIPS32_R1 is not set
-# CONFIG_CPU_MIPS32_R2 is not set
-# CONFIG_CPU_MIPS64_R1 is not set
-# CONFIG_CPU_MIPS64_R2 is not set
-# CONFIG_CPU_R3000 is not set
-# CONFIG_CPU_TX39XX is not set
-# CONFIG_CPU_VR41XX is not set
-# CONFIG_CPU_R4300 is not set
-# CONFIG_CPU_R4X00 is not set
-# CONFIG_CPU_TX49XX is not set
-# CONFIG_CPU_R5000 is not set
-CONFIG_CPU_R5432=y
-# CONFIG_CPU_R6000 is not set
-# CONFIG_CPU_NEVADA is not set
-# CONFIG_CPU_R8000 is not set
-# CONFIG_CPU_R10000 is not set
-# CONFIG_CPU_RM7000 is not set
-# CONFIG_CPU_RM9000 is not set
-# CONFIG_CPU_SB1 is not set
-CONFIG_SYS_HAS_CPU_R5432=y
-CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y
-CONFIG_SYS_SUPPORTS_64BIT_KERNEL=y
-CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y
-CONFIG_CPU_SUPPORTS_64BIT_KERNEL=y
-
-#
-# Kernel type
-#
-CONFIG_32BIT=y
-# CONFIG_64BIT is not set
-CONFIG_PAGE_SIZE_4KB=y
-# CONFIG_PAGE_SIZE_8KB is not set
-# CONFIG_PAGE_SIZE_16KB is not set
-# CONFIG_PAGE_SIZE_64KB is not set
-CONFIG_MIPS_MT_DISABLED=y
-# CONFIG_MIPS_MT_SMP is not set
-# CONFIG_MIPS_MT_SMTC is not set
-# CONFIG_MIPS_VPE_LOADER is not set
-CONFIG_CPU_HAS_LLSC=y
-CONFIG_CPU_HAS_SYNC=y
-CONFIG_GENERIC_HARDIRQS=y
-CONFIG_GENERIC_IRQ_PROBE=y
-CONFIG_ARCH_FLATMEM_ENABLE=y
-CONFIG_SELECT_MEMORY_MODEL=y
-CONFIG_FLATMEM_MANUAL=y
-# CONFIG_DISCONTIGMEM_MANUAL is not set
-# CONFIG_SPARSEMEM_MANUAL is not set
-CONFIG_FLATMEM=y
-CONFIG_FLAT_NODE_MEM_MAP=y
-# CONFIG_SPARSEMEM_STATIC is not set
-CONFIG_SPLIT_PTLOCK_CPUS=4
-# CONFIG_RESOURCES_64BIT is not set
-CONFIG_ZONE_DMA_FLAG=1
-# CONFIG_HZ_48 is not set
-# CONFIG_HZ_100 is not set
-# CONFIG_HZ_128 is not set
-# CONFIG_HZ_250 is not set
-# CONFIG_HZ_256 is not set
-CONFIG_HZ_1000=y
-# CONFIG_HZ_1024 is not set
-CONFIG_SYS_SUPPORTS_ARBIT_HZ=y
-CONFIG_HZ=1000
-CONFIG_PREEMPT_NONE=y
-# CONFIG_PREEMPT_VOLUNTARY is not set
-# CONFIG_PREEMPT is not set
-# CONFIG_KEXEC is not set
-CONFIG_LOCKDEP_SUPPORT=y
-CONFIG_STACKTRACE_SUPPORT=y
-CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
-
-#
-# Code maturity level options
-#
-CONFIG_EXPERIMENTAL=y
-CONFIG_BROKEN_ON_SMP=y
-CONFIG_INIT_ENV_ARG_LIMIT=32
-
-#
-# General setup
-#
-CONFIG_LOCALVERSION=""
-CONFIG_LOCALVERSION_AUTO=y
-CONFIG_SWAP=y
-CONFIG_SYSVIPC=y
-# CONFIG_IPC_NS is not set
-CONFIG_SYSVIPC_SYSCTL=y
-# CONFIG_POSIX_MQUEUE is not set
-# CONFIG_BSD_PROCESS_ACCT is not set
-# CONFIG_TASKSTATS is not set
-# CONFIG_UTS_NS is not set
-# CONFIG_AUDIT is not set
-# CONFIG_IKCONFIG is not set
-CONFIG_SYSFS_DEPRECATED=y
-CONFIG_RELAY=y
-# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
-CONFIG_SYSCTL=y
-CONFIG_EMBEDDED=y
-CONFIG_SYSCTL_SYSCALL=y
-CONFIG_KALLSYMS=y
-# CONFIG_KALLSYMS_EXTRA_PASS is not set
-CONFIG_HOTPLUG=y
-CONFIG_PRINTK=y
-CONFIG_BUG=y
-CONFIG_ELF_CORE=y
-CONFIG_BASE_FULL=y
-CONFIG_FUTEX=y
-CONFIG_EPOLL=y
-CONFIG_SHMEM=y
-CONFIG_SLAB=y
-CONFIG_VM_EVENT_COUNTERS=y
-CONFIG_RT_MUTEXES=y
-# CONFIG_TINY_SHMEM is not set
-CONFIG_BASE_SMALL=0
-# CONFIG_SLOB is not set
-
-#
-# Loadable module support
-#
-# CONFIG_MODULES is not set
-
-#
-# Block layer
-#
-CONFIG_BLOCK=y
-# CONFIG_LBD is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
-# CONFIG_LSF is not set
-
-#
-# IO Schedulers
-#
-CONFIG_IOSCHED_NOOP=y
-CONFIG_IOSCHED_AS=y
-CONFIG_IOSCHED_DEADLINE=y
-CONFIG_IOSCHED_CFQ=y
-CONFIG_DEFAULT_AS=y
-# CONFIG_DEFAULT_DEADLINE is not set
-# CONFIG_DEFAULT_CFQ is not set
-# CONFIG_DEFAULT_NOOP is not set
-CONFIG_DEFAULT_IOSCHED="anticipatory"
-
-#
-# Bus options (PCI, PCMCIA, EISA, ISA, TC)
-#
-CONFIG_HW_HAS_PCI=y
-CONFIG_PCI=y
-CONFIG_MMU=y
-
-#
-# PCCARD (PCMCIA/CardBus) support
-#
-# CONFIG_PCCARD is not set
-
-#
-# PCI Hotplug Support
-#
-# CONFIG_HOTPLUG_PCI is not set
-
-#
-# Executable file formats
-#
-CONFIG_BINFMT_ELF=y
-# CONFIG_BINFMT_MISC is not set
-CONFIG_TRAD_SIGNALS=y
-
-#
-# Power management options
-#
-CONFIG_PM=y
-# CONFIG_PM_LEGACY is not set
-# CONFIG_PM_DEBUG is not set
-# CONFIG_PM_SYSFS_DEPRECATED is not set
-
-#
-# Networking
-#
-CONFIG_NET=y
-
-#
-# Networking options
-#
-# CONFIG_NETDEBUG is not set
-CONFIG_PACKET=y
-# CONFIG_PACKET_MMAP is not set
-CONFIG_UNIX=y
-CONFIG_XFRM=y
-CONFIG_XFRM_USER=y
-# CONFIG_XFRM_SUB_POLICY is not set
-CONFIG_XFRM_MIGRATE=y
-CONFIG_NET_KEY=y
-CONFIG_NET_KEY_MIGRATE=y
-CONFIG_INET=y
-# CONFIG_IP_MULTICAST is not set
-# CONFIG_IP_ADVANCED_ROUTER is not set
-CONFIG_IP_FIB_HASH=y
-CONFIG_IP_PNP=y
-# CONFIG_IP_PNP_DHCP is not set
-CONFIG_IP_PNP_BOOTP=y
-# CONFIG_IP_PNP_RARP is not set
-# CONFIG_NET_IPIP is not set
-# CONFIG_NET_IPGRE is not set
-# CONFIG_ARPD is not set
-# CONFIG_SYN_COOKIES is not set
-# CONFIG_INET_AH is not set
-# CONFIG_INET_ESP is not set
-# CONFIG_INET_IPCOMP is not set
-# CONFIG_INET_XFRM_TUNNEL is not set
-# CONFIG_INET_TUNNEL is not set
-CONFIG_INET_XFRM_MODE_TRANSPORT=y
-CONFIG_INET_XFRM_MODE_TUNNEL=y
-CONFIG_INET_XFRM_MODE_BEET=y
-CONFIG_INET_DIAG=y
-CONFIG_INET_TCP_DIAG=y
-# CONFIG_TCP_CONG_ADVANCED is not set
-CONFIG_TCP_CONG_CUBIC=y
-CONFIG_DEFAULT_TCP_CONG="cubic"
-CONFIG_TCP_MD5SIG=y
-# CONFIG_IPV6 is not set
-# CONFIG_INET6_XFRM_TUNNEL is not set
-# CONFIG_INET6_TUNNEL is not set
-CONFIG_NETWORK_SECMARK=y
-# CONFIG_NETFILTER is not set
-
-#
-# DCCP Configuration (EXPERIMENTAL)
-#
-# CONFIG_IP_DCCP is not set
-
-#
-# SCTP Configuration (EXPERIMENTAL)
-#
-# CONFIG_IP_SCTP is not set
-
-#
-# TIPC Configuration (EXPERIMENTAL)
-#
-# CONFIG_TIPC is not set
-# CONFIG_ATM is not set
-# CONFIG_BRIDGE is not set
-# CONFIG_VLAN_8021Q is not set
-# CONFIG_DECNET is not set
-# CONFIG_LLC2 is not set
-# CONFIG_IPX is not set
-# CONFIG_ATALK is not set
-# CONFIG_X25 is not set
-# CONFIG_LAPB is not set
-# CONFIG_ECONET is not set
-# CONFIG_WAN_ROUTER is not set
-
-#
-# QoS and/or fair queueing
-#
-# CONFIG_NET_SCHED is not set
-
-#
-# Network testing
-#
-# CONFIG_NET_PKTGEN is not set
-# CONFIG_HAMRADIO is not set
-# CONFIG_IRDA is not set
-# CONFIG_BT is not set
-CONFIG_IEEE80211=y
-# CONFIG_IEEE80211_DEBUG is not set
-CONFIG_IEEE80211_CRYPT_WEP=y
-CONFIG_IEEE80211_CRYPT_CCMP=y
-CONFIG_IEEE80211_SOFTMAC=y
-# CONFIG_IEEE80211_SOFTMAC_DEBUG is not set
-CONFIG_WIRELESS_EXT=y
-
-#
-# Device Drivers
-#
-
-#
-# Generic Driver Options
-#
-CONFIG_STANDALONE=y
-CONFIG_PREVENT_FIRMWARE_BUILD=y
-CONFIG_FW_LOADER=y
-# CONFIG_SYS_HYPERVISOR is not set
-
-#
-# Connector - unified userspace <-> kernelspace linker
-#
-CONFIG_CONNECTOR=y
-CONFIG_PROC_EVENTS=y
-
-#
-# Memory Technology Devices (MTD)
-#
-# CONFIG_MTD is not set
-
-#
-# Parallel port support
-#
-# CONFIG_PARPORT is not set
-
-#
-# Plug and Play support
-#
-# CONFIG_PNPACPI is not set
-
-#
-# Block devices
-#
-# CONFIG_BLK_CPQ_DA is not set
-# CONFIG_BLK_CPQ_CISS_DA is not set
-# CONFIG_BLK_DEV_DAC960 is not set
-# CONFIG_BLK_DEV_UMEM is not set
-# CONFIG_BLK_DEV_COW_COMMON is not set
-# CONFIG_BLK_DEV_LOOP is not set
-# CONFIG_BLK_DEV_NBD is not set
-# CONFIG_BLK_DEV_SX8 is not set
-# CONFIG_BLK_DEV_RAM is not set
-# CONFIG_BLK_DEV_INITRD is not set
-CONFIG_CDROM_PKTCDVD=y
-CONFIG_CDROM_PKTCDVD_BUFFERS=8
-# CONFIG_CDROM_PKTCDVD_WCACHE is not set
-CONFIG_ATA_OVER_ETH=y
-
-#
-# Misc devices
-#
-CONFIG_SGI_IOC4=y
-# CONFIG_TIFM_CORE is not set
-
-#
-# ATA/ATAPI/MFM/RLL support
-#
-# CONFIG_IDE is not set
-
-#
-# SCSI device support
-#
-CONFIG_RAID_ATTRS=y
-# CONFIG_SCSI is not set
-# CONFIG_SCSI_NETLINK is not set
-
-#
-# Serial ATA (prod) and Parallel ATA (experimental) drivers
-#
-# CONFIG_ATA is not set
-
-#
-# Multi-device support (RAID and LVM)
-#
-# CONFIG_MD is not set
-
-#
-# Fusion MPT device support
-#
-# CONFIG_FUSION is not set
-
-#
-# IEEE 1394 (FireWire) support
-#
-# CONFIG_IEEE1394 is not set
-
-#
-# I2O device support
-#
-# CONFIG_I2O is not set
-
-#
-# Network device support
-#
-CONFIG_NETDEVICES=y
-# CONFIG_DUMMY is not set
-# CONFIG_BONDING is not set
-# CONFIG_EQUALIZER is not set
-# CONFIG_TUN is not set
-
-#
-# ARCnet devices
-#
-# CONFIG_ARCNET is not set
-
-#
-# PHY device support
-#
-CONFIG_PHYLIB=y
-
-#
-# MII PHY device drivers
-#
-CONFIG_MARVELL_PHY=y
-CONFIG_DAVICOM_PHY=y
-CONFIG_QSEMI_PHY=y
-CONFIG_LXT_PHY=y
-CONFIG_CICADA_PHY=y
-CONFIG_VITESSE_PHY=y
-CONFIG_SMSC_PHY=y
-# CONFIG_BROADCOM_PHY is not set
-# CONFIG_FIXED_PHY is not set
-
-#
-# Ethernet (10 or 100Mbit)
-#
-CONFIG_NET_ETHERNET=y
-CONFIG_MII=y
-# CONFIG_HAPPYMEAL is not set
-# CONFIG_SUNGEM is not set
-# CONFIG_CASSINI is not set
-# CONFIG_NET_VENDOR_3COM is not set
-# CONFIG_DM9000 is not set
-
-#
-# Tulip family network device support
-#
-# CONFIG_NET_TULIP is not set
-# CONFIG_HP100 is not set
-CONFIG_NET_PCI=y
-CONFIG_PCNET32=y
-# CONFIG_PCNET32_NAPI is not set
-# CONFIG_AMD8111_ETH is not set
-# CONFIG_ADAPTEC_STARFIRE is not set
-# CONFIG_B44 is not set
-# CONFIG_FORCEDETH is not set
-# CONFIG_DGRS is not set
-# CONFIG_EEPRO100 is not set
-# CONFIG_E100 is not set
-# CONFIG_FEALNX is not set
-# CONFIG_NATSEMI is not set
-# CONFIG_NE2K_PCI is not set
-# CONFIG_8139CP is not set
-# CONFIG_8139TOO is not set
-# CONFIG_SIS900 is not set
-# CONFIG_EPIC100 is not set
-# CONFIG_SUNDANCE is not set
-# CONFIG_TLAN is not set
-# CONFIG_VIA_RHINE is not set
-# CONFIG_SC92031 is not set
-
-#
-# Ethernet (1000 Mbit)
-#
-# CONFIG_ACENIC is not set
-# CONFIG_DL2K is not set
-# CONFIG_E1000 is not set
-# CONFIG_NS83820 is not set
-# CONFIG_HAMACHI is not set
-# CONFIG_YELLOWFIN is not set
-# CONFIG_R8169 is not set
-# CONFIG_SIS190 is not set
-# CONFIG_SKGE is not set
-# CONFIG_SKY2 is not set
-# CONFIG_SK98LIN is not set
-# CONFIG_VIA_VELOCITY is not set
-# CONFIG_TIGON3 is not set
-# CONFIG_BNX2 is not set
-CONFIG_QLA3XXX=y
-# CONFIG_ATL1 is not set
-
-#
-# Ethernet (10000 Mbit)
-#
-# CONFIG_CHELSIO_T1 is not set
-CONFIG_CHELSIO_T3=y
-# CONFIG_IXGB is not set
-# CONFIG_S2IO is not set
-# CONFIG_MYRI10GE is not set
-CONFIG_NETXEN_NIC=y
-
-#
-# Token Ring devices
-#
-# CONFIG_TR is not set
-
-#
-# Wireless LAN (non-hamradio)
-#
-# CONFIG_NET_RADIO is not set
-
-#
-# Wan interfaces
-#
-# CONFIG_WAN is not set
-# CONFIG_FDDI is not set
-# CONFIG_HIPPI is not set
-# CONFIG_PPP is not set
-# CONFIG_SLIP is not set
-# CONFIG_SHAPER is not set
-# CONFIG_NETCONSOLE is not set
-# CONFIG_NETPOLL is not set
-# CONFIG_NET_POLL_CONTROLLER is not set
-
-#
-# ISDN subsystem
-#
-# CONFIG_ISDN is not set
-
-#
-# Telephony Support
-#
-# CONFIG_PHONE is not set
-
-#
-# Input device support
-#
-CONFIG_INPUT=y
-# CONFIG_INPUT_FF_MEMLESS is not set
-
-#
-# Userland interfaces
-#
-CONFIG_INPUT_MOUSEDEV=y
-CONFIG_INPUT_MOUSEDEV_PSAUX=y
-CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
-CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
-# CONFIG_INPUT_JOYDEV is not set
-# CONFIG_INPUT_TSDEV is not set
-# CONFIG_INPUT_EVDEV is not set
-# CONFIG_INPUT_EVBUG is not set
-
-#
-# Input Device Drivers
-#
-# CONFIG_INPUT_KEYBOARD is not set
-# CONFIG_INPUT_MOUSE is not set
-# CONFIG_INPUT_JOYSTICK is not set
-# CONFIG_INPUT_TOUCHSCREEN is not set
-# CONFIG_INPUT_MISC is not set
-
-#
-# Hardware I/O ports
-#
-CONFIG_SERIO=y
-# CONFIG_SERIO_I8042 is not set
-CONFIG_SERIO_SERPORT=y
-# CONFIG_SERIO_PCIPS2 is not set
-# CONFIG_SERIO_LIBPS2 is not set
-CONFIG_SERIO_RAW=y
-# CONFIG_GAMEPORT is not set
-
-#
-# Character devices
-#
-CONFIG_VT=y
-CONFIG_VT_CONSOLE=y
-CONFIG_HW_CONSOLE=y
-CONFIG_VT_HW_CONSOLE_BINDING=y
-# CONFIG_SERIAL_NONSTANDARD is not set
-
-#
-# Serial drivers
-#
-CONFIG_SERIAL_8250=y
-CONFIG_SERIAL_8250_CONSOLE=y
-CONFIG_SERIAL_8250_PCI=y
-CONFIG_SERIAL_8250_NR_UARTS=4
-CONFIG_SERIAL_8250_RUNTIME_UARTS=4
-# CONFIG_SERIAL_8250_EXTENDED is not set
-
-#
-# Non-8250 serial port support
-#
-CONFIG_SERIAL_CORE=y
-CONFIG_SERIAL_CORE_CONSOLE=y
-# CONFIG_SERIAL_JSM is not set
-CONFIG_UNIX98_PTYS=y
-CONFIG_LEGACY_PTYS=y
-CONFIG_LEGACY_PTY_COUNT=256
-
-#
-# IPMI
-#
-# CONFIG_IPMI_HANDLER is not set
-
-#
-# Watchdog Cards
-#
-# CONFIG_WATCHDOG is not set
-# CONFIG_HW_RANDOM is not set
-# CONFIG_RTC is not set
-# CONFIG_GEN_RTC is not set
-# CONFIG_DTLK is not set
-# CONFIG_R3964 is not set
-# CONFIG_APPLICOM is not set
-# CONFIG_DRM is not set
-# CONFIG_RAW_DRIVER is not set
-
-#
-# TPM devices
-#
-# CONFIG_TCG_TPM is not set
-
-#
-# I2C support
-#
-# CONFIG_I2C is not set
-
-#
-# SPI support
-#
-# CONFIG_SPI is not set
-# CONFIG_SPI_MASTER is not set
-
-#
-# Dallas's 1-wire bus
-#
-# CONFIG_W1 is not set
-
-#
-# Hardware Monitoring support
-#
-# CONFIG_HWMON is not set
-# CONFIG_HWMON_VID is not set
-
-#
-# Multimedia devices
-#
-# CONFIG_VIDEO_DEV is not set
-
-#
-# Digital Video Broadcasting Devices
-#
-# CONFIG_DVB is not set
-
-#
-# Graphics support
-#
-# CONFIG_FIRMWARE_EDID is not set
-# CONFIG_FB is not set
-
-#
-# Console display driver support
-#
-# CONFIG_VGA_CONSOLE is not set
-CONFIG_DUMMY_CONSOLE=y
-# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
-
-#
-# Sound
-#
-# CONFIG_SOUND is not set
-
-#
-# HID Devices
-#
-# CONFIG_HID is not set
-
-#
-# USB support
-#
-CONFIG_USB_ARCH_HAS_HCD=y
-CONFIG_USB_ARCH_HAS_OHCI=y
-CONFIG_USB_ARCH_HAS_EHCI=y
-# CONFIG_USB is not set
-
-#
-# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
-#
-
-#
-# USB Gadget Support
-#
-# CONFIG_USB_GADGET is not set
-
-#
-# MMC/SD Card support
-#
-# CONFIG_MMC is not set
-
-#
-# LED devices
-#
-# CONFIG_NEW_LEDS is not set
-
-#
-# LED drivers
-#
-
-#
-# LED Triggers
-#
-
-#
-# InfiniBand support
-#
-# CONFIG_INFINIBAND is not set
-
-#
-# EDAC - error detection and reporting (RAS) (EXPERIMENTAL)
-#
-
-#
-# Real Time Clock
-#
-# CONFIG_RTC_CLASS is not set
-
-#
-# DMA Engine support
-#
-# CONFIG_DMA_ENGINE is not set
-
-#
-# DMA Clients
-#
-
-#
-# DMA Devices
-#
-
-#
-# Auxiliary Display support
-#
-
-#
-# Virtualization
-#
-
-#
-# File systems
-#
-CONFIG_EXT2_FS=y
-# CONFIG_EXT2_FS_XATTR is not set
-# CONFIG_EXT2_FS_XIP is not set
-# CONFIG_EXT3_FS is not set
-# CONFIG_EXT4DEV_FS is not set
-# CONFIG_REISERFS_FS is not set
-# CONFIG_JFS_FS is not set
-# CONFIG_FS_POSIX_ACL is not set
-# CONFIG_XFS_FS is not set
-# CONFIG_GFS2_FS is not set
-# CONFIG_OCFS2_FS is not set
-# CONFIG_MINIX_FS is not set
-# CONFIG_ROMFS_FS is not set
-CONFIG_INOTIFY=y
-CONFIG_INOTIFY_USER=y
-# CONFIG_QUOTA is not set
-CONFIG_DNOTIFY=y
-CONFIG_AUTOFS_FS=y
-CONFIG_AUTOFS4_FS=y
-CONFIG_FUSE_FS=y
-
-#
-# CD-ROM/DVD Filesystems
-#
-# CONFIG_ISO9660_FS is not set
-# CONFIG_UDF_FS is not set
-
-#
-# DOS/FAT/NT Filesystems
-#
-# CONFIG_MSDOS_FS is not set
-# CONFIG_VFAT_FS is not set
-# CONFIG_NTFS_FS is not set
-
-#
-# Pseudo filesystems
-#
-CONFIG_PROC_FS=y
-CONFIG_PROC_KCORE=y
-CONFIG_PROC_SYSCTL=y
-CONFIG_SYSFS=y
-# CONFIG_TMPFS is not set
-# CONFIG_HUGETLB_PAGE is not set
-CONFIG_RAMFS=y
-CONFIG_CONFIGFS_FS=y
-
-#
-# Miscellaneous filesystems
-#
-# CONFIG_ADFS_FS is not set
-# CONFIG_AFFS_FS is not set
-# CONFIG_ECRYPT_FS is not set
-# CONFIG_HFS_FS is not set
-# CONFIG_HFSPLUS_FS is not set
-# CONFIG_BEFS_FS is not set
-# CONFIG_BFS_FS is not set
-# CONFIG_EFS_FS is not set
-# CONFIG_CRAMFS is not set
-# CONFIG_VXFS_FS is not set
-# CONFIG_HPFS_FS is not set
-# CONFIG_QNX4FS_FS is not set
-# CONFIG_SYSV_FS is not set
-# CONFIG_UFS_FS is not set
-
-#
-# Network File Systems
-#
-CONFIG_NFS_FS=y
-# CONFIG_NFS_V3 is not set
-# CONFIG_NFS_V4 is not set
-# CONFIG_NFS_DIRECTIO is not set
-CONFIG_NFSD=y
-# CONFIG_NFSD_V3 is not set
-# CONFIG_NFSD_TCP is not set
-CONFIG_ROOT_NFS=y
-CONFIG_LOCKD=y
-CONFIG_EXPORTFS=y
-CONFIG_NFS_COMMON=y
-CONFIG_SUNRPC=y
-# CONFIG_RPCSEC_GSS_KRB5 is not set
-# CONFIG_RPCSEC_GSS_SPKM3 is not set
-# CONFIG_SMB_FS is not set
-# CONFIG_CIFS is not set
-# CONFIG_NCP_FS is not set
-# CONFIG_CODA_FS is not set
-# CONFIG_AFS_FS is not set
-# CONFIG_9P_FS is not set
-
-#
-# Partition Types
-#
-# CONFIG_PARTITION_ADVANCED is not set
-CONFIG_MSDOS_PARTITION=y
-
-#
-# Native Language Support
-#
-# CONFIG_NLS is not set
-
-#
-# Distributed Lock Manager
-#
-CONFIG_DLM=y
-CONFIG_DLM_TCP=y
-# CONFIG_DLM_SCTP is not set
-# CONFIG_DLM_DEBUG is not set
-
-#
-# Profiling support
-#
-# CONFIG_PROFILING is not set
-
-#
-# Kernel hacking
-#
-CONFIG_TRACE_IRQFLAGS_SUPPORT=y
-# CONFIG_PRINTK_TIME is not set
-CONFIG_ENABLE_MUST_CHECK=y
-# CONFIG_MAGIC_SYSRQ is not set
-# CONFIG_UNUSED_SYMBOLS is not set
-# CONFIG_DEBUG_FS is not set
-# CONFIG_HEADERS_CHECK is not set
-# CONFIG_DEBUG_KERNEL is not set
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_CROSSCOMPILE=y
-CONFIG_CMDLINE="ip=any"
-CONFIG_SYS_SUPPORTS_KGDB=y
-
-#
-# Security options
-#
-CONFIG_KEYS=y
-CONFIG_KEYS_DEBUG_PROC_KEYS=y
-# CONFIG_SECURITY is not set
-
-#
-# Cryptographic options
-#
-CONFIG_CRYPTO=y
-CONFIG_CRYPTO_ALGAPI=y
-CONFIG_CRYPTO_BLKCIPHER=y
-CONFIG_CRYPTO_HASH=y
-CONFIG_CRYPTO_MANAGER=y
-CONFIG_CRYPTO_HMAC=y
-CONFIG_CRYPTO_XCBC=y
-CONFIG_CRYPTO_NULL=y
-CONFIG_CRYPTO_MD4=y
-CONFIG_CRYPTO_MD5=y
-CONFIG_CRYPTO_SHA1=y
-CONFIG_CRYPTO_SHA256=y
-CONFIG_CRYPTO_SHA512=y
-CONFIG_CRYPTO_WP512=y
-CONFIG_CRYPTO_TGR192=y
-CONFIG_CRYPTO_GF128MUL=y
-CONFIG_CRYPTO_ECB=y
-CONFIG_CRYPTO_CBC=y
-CONFIG_CRYPTO_PCBC=y
-CONFIG_CRYPTO_LRW=y
-CONFIG_CRYPTO_DES=y
-CONFIG_CRYPTO_FCRYPT=y
-CONFIG_CRYPTO_BLOWFISH=y
-CONFIG_CRYPTO_TWOFISH=y
-CONFIG_CRYPTO_TWOFISH_COMMON=y
-CONFIG_CRYPTO_SERPENT=y
-CONFIG_CRYPTO_AES=y
-CONFIG_CRYPTO_CAST5=y
-CONFIG_CRYPTO_CAST6=y
-CONFIG_CRYPTO_TEA=y
-CONFIG_CRYPTO_ARC4=y
-CONFIG_CRYPTO_KHAZAD=y
-CONFIG_CRYPTO_ANUBIS=y
-CONFIG_CRYPTO_DEFLATE=y
-CONFIG_CRYPTO_MICHAEL_MIC=y
-CONFIG_CRYPTO_CRC32C=y
-CONFIG_CRYPTO_CAMELLIA=y
-
-#
-# Hardware crypto devices
-#
-
-#
-# Library routines
-#
-CONFIG_BITREVERSE=y
-# CONFIG_CRC_CCITT is not set
-CONFIG_CRC16=y
-CONFIG_CRC32=y
-CONFIG_LIBCRC32C=y
-CONFIG_ZLIB_INFLATE=y
-CONFIG_ZLIB_DEFLATE=y
-CONFIG_PLIST=y
-CONFIG_HAS_IOMEM=y
-CONFIG_HAS_IOPORT=y
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
-# CONFIG_DDB5477 is not set
# CONFIG_MACH_VR41XX is not set
# CONFIG_PMC_YOSEMITE is not set
# CONFIG_QEMU is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
-# CONFIG_DDB5477 is not set
CONFIG_MACH_VR41XX=y
# CONFIG_PMC_YOSEMITE is not set
# CONFIG_QEMU is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
-# CONFIG_DDB5477 is not set
# CONFIG_MACH_VR41XX is not set
# CONFIG_PMC_YOSEMITE is not set
# CONFIG_QEMU is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
-# CONFIG_DDB5477 is not set
# CONFIG_MACH_VR41XX is not set
# CONFIG_PMC_YOSEMITE is not set
# CONFIG_QEMU is not set
# CONFIG_MIPS_SIM is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
-# CONFIG_DDB5477 is not set
# CONFIG_MACH_VR41XX is not set
# CONFIG_PMC_YOSEMITE is not set
# CONFIG_QEMU is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
-# CONFIG_DDB5477 is not set
# CONFIG_MACH_VR41XX is not set
# CONFIG_PMC_YOSEMITE is not set
# CONFIG_QEMU is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
-# CONFIG_DDB5477 is not set
# CONFIG_MACH_VR41XX is not set
# CONFIG_PMC_YOSEMITE is not set
# CONFIG_QEMU is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
-# CONFIG_DDB5477 is not set
# CONFIG_MACH_VR41XX is not set
# CONFIG_PMC_YOSEMITE is not set
# CONFIG_QEMU is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
-# CONFIG_DDB5477 is not set
# CONFIG_MACH_VR41XX is not set
# CONFIG_PMC_YOSEMITE is not set
# CONFIG_QEMU is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
-# CONFIG_DDB5477 is not set
# CONFIG_MACH_VR41XX is not set
# CONFIG_PMC_YOSEMITE is not set
# CONFIG_QEMU is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
-# CONFIG_DDB5477 is not set
# CONFIG_MACH_VR41XX is not set
# CONFIG_PMC_YOSEMITE is not set
# CONFIG_QEMU is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
-# CONFIG_DDB5477 is not set
# CONFIG_MACH_VR41XX is not set
# CONFIG_PMC_YOSEMITE is not set
# CONFIG_QEMU is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
-# CONFIG_DDB5477 is not set
CONFIG_MACH_VR41XX=y
# CONFIG_PMC_YOSEMITE is not set
# CONFIG_QEMU is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
-# CONFIG_DDB5477 is not set
# CONFIG_MACH_VR41XX is not set
CONFIG_PMC_MSP=y
# CONFIG_PMC_YOSEMITE is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
-# CONFIG_DDB5477 is not set
# CONFIG_MACH_VR41XX is not set
# CONFIG_PMC_YOSEMITE is not set
# CONFIG_QEMU is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
-# CONFIG_DDB5477 is not set
# CONFIG_MACH_VR41XX is not set
# CONFIG_PMC_YOSEMITE is not set
# CONFIG_QEMU is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
-# CONFIG_DDB5477 is not set
# CONFIG_MACH_VR41XX is not set
# CONFIG_PMC_YOSEMITE is not set
# CONFIG_QEMU is not set
# CONFIG_MIPS_XXS1500 is not set
CONFIG_PNX8550_JBS=y
# CONFIG_PNX8550_STB810 is not set
-# CONFIG_DDB5477 is not set
# CONFIG_MACH_VR41XX is not set
# CONFIG_PMC_YOSEMITE is not set
# CONFIG_QEMU is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
CONFIG_PNX8550_STB810=y
-# CONFIG_DDB5477 is not set
# CONFIG_MACH_VR41XX is not set
# CONFIG_PMC_YOSEMITE is not set
# CONFIG_QEMU is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
-# CONFIG_DDB5477 is not set
# CONFIG_MACH_VR41XX is not set
# CONFIG_PMC_YOSEMITE is not set
CONFIG_QEMU=y
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
-# CONFIG_DDB5477 is not set
# CONFIG_MACH_VR41XX is not set
# CONFIG_PMC_YOSEMITE is not set
# CONFIG_QEMU is not set
# CONFIG_MIPS_SIM is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
-# CONFIG_DDB5477 is not set
# CONFIG_MACH_VR41XX is not set
# CONFIG_PMC_MSP is not set
# CONFIG_PMC_YOSEMITE is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
-# CONFIG_DDB5477 is not set
# CONFIG_MACH_VR41XX is not set
# CONFIG_PMC_YOSEMITE is not set
# CONFIG_QEMU is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
-# CONFIG_DDB5477 is not set
# CONFIG_MACH_VR41XX is not set
# CONFIG_PMC_YOSEMITE is not set
# CONFIG_QEMU is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
-# CONFIG_DDB5477 is not set
# CONFIG_MACH_VR41XX is not set
# CONFIG_PMC_YOSEMITE is not set
# CONFIG_QEMU is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
-# CONFIG_DDB5477 is not set
CONFIG_MACH_VR41XX=y
# CONFIG_PMC_YOSEMITE is not set
# CONFIG_QEMU is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
-# CONFIG_DDB5477 is not set
CONFIG_MACH_VR41XX=y
# CONFIG_PMC_YOSEMITE is not set
# CONFIG_QEMU is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
-# CONFIG_DDB5477 is not set
CONFIG_MACH_VR41XX=y
# CONFIG_PMC_YOSEMITE is not set
# CONFIG_QEMU is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
-# CONFIG_DDB5477 is not set
CONFIG_MACH_VR41XX=y
# CONFIG_PMC_YOSEMITE is not set
# CONFIG_QEMU is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
-# CONFIG_DDB5477 is not set
# CONFIG_MACH_VR41XX is not set
# CONFIG_PMC_YOSEMITE is not set
# CONFIG_QEMU is not set
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
-# CONFIG_DDB5477 is not set
# CONFIG_MACH_VR41XX is not set
CONFIG_PMC_YOSEMITE=y
# CONFIG_QEMU is not set
+++ /dev/null
-config DDB5477_BUS_FREQUENCY
- int "bus frequency (in kHZ, 0 for auto-detect)"
- depends on DDB5477
- default 0
+++ /dev/null
-#
-# Makefile for the common code of NEC DDB-Vrc5xxx board
-#
-
-obj-y += nile4.o prom.o rtc_ds1386.o
-
-EXTRA_CFLAGS += -Werror
+++ /dev/null
-/*
- *
- * Copyright 2001 MontaVista Software Inc.
- * Author: jsun@mvista.com or jsun@junsun.net
- *
- * arch/mips/ddb5xxx/common/nile4.c
- * misc low-level routines for vrc-5xxx controllers.
- *
- * derived from original code by Geert Uytterhoeven <geert@sonycom.com>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- */
-#include <linux/types.h>
-#include <linux/kernel.h>
-
-#include <asm/ddb5xxx/ddb5xxx.h>
-
-u32
-ddb_calc_pdar(u32 phys, u32 size, int width,
- int on_memory_bus, int pci_visible)
-{
- u32 maskbits;
- u32 widthbits;
-
- switch (size) {
-#if 0 /* We don't support 4 GB yet */
- case 0x100000000: /* 4 GB */
- maskbits = 4;
- break;
-#endif
- case 0x80000000: /* 2 GB */
- maskbits = 5;
- break;
- case 0x40000000: /* 1 GB */
- maskbits = 6;
- break;
- case 0x20000000: /* 512 MB */
- maskbits = 7;
- break;
- case 0x10000000: /* 256 MB */
- maskbits = 8;
- break;
- case 0x08000000: /* 128 MB */
- maskbits = 9;
- break;
- case 0x04000000: /* 64 MB */
- maskbits = 10;
- break;
- case 0x02000000: /* 32 MB */
- maskbits = 11;
- break;
- case 0x01000000: /* 16 MB */
- maskbits = 12;
- break;
- case 0x00800000: /* 8 MB */
- maskbits = 13;
- break;
- case 0x00400000: /* 4 MB */
- maskbits = 14;
- break;
- case 0x00200000: /* 2 MB */
- maskbits = 15;
- break;
- case 0: /* OFF */
- maskbits = 0;
- break;
- default:
- panic("nile4_set_pdar: unsupported size %p", (void *) size);
- }
- switch (width) {
- case 8:
- widthbits = 0;
- break;
- case 16:
- widthbits = 1;
- break;
- case 32:
- widthbits = 2;
- break;
- case 64:
- widthbits = 3;
- break;
- default:
- panic("nile4_set_pdar: unsupported width %d", width);
- }
-
- return maskbits | (on_memory_bus ? 0x10 : 0) |
- (pci_visible ? 0x20 : 0) | (widthbits << 6) |
- (phys & 0xffe00000);
-}
-
-void
-ddb_set_pdar(u32 pdar, u32 phys, u32 size, int width,
- int on_memory_bus, int pci_visible)
-{
- u32 temp= ddb_calc_pdar(phys, size, width, on_memory_bus, pci_visible);
- ddb_out32(pdar, temp);
- ddb_out32(pdar + 4, 0);
-
- /*
- * When programming a PDAR, the register should be read immediately
- * after writing it. This ensures that address decoders are properly
- * configured.
- * [jsun] is this really necessary?
- */
- ddb_in32(pdar);
- ddb_in32(pdar + 4);
-}
-
-/*
- * routines that mess with PCIINITx registers
- */
-
-void ddb_set_pmr(u32 pmr, u32 type, u32 addr, u32 options)
-{
- switch (type) {
- case DDB_PCICMD_IACK: /* PCI Interrupt Acknowledge */
- case DDB_PCICMD_IO: /* PCI I/O Space */
- case DDB_PCICMD_MEM: /* PCI Memory Space */
- case DDB_PCICMD_CFG: /* PCI Configuration Space */
- break;
- default:
- panic("nile4_set_pmr: invalid type %d", type);
- }
- ddb_out32(pmr, (type << 1) | (addr & 0xffe00000) | options );
- ddb_out32(pmr + 4, 0);
-}
+++ /dev/null
-/*
- * Copyright 2001 MontaVista Software Inc.
- * Author: jsun@mvista.com or jsun@junsun.net
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- */
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/sched.h>
-#include <linux/bootmem.h>
-
-#include <asm/addrspace.h>
-#include <asm/bootinfo.h>
-#include <asm/ddb5xxx/ddb5xxx.h>
-#include <asm/debug.h>
-
-const char *get_system_type(void)
-{
- switch (mips_machtype) {
- case MACH_NEC_DDB5477: return "NEC DDB Vrc-5477";
- case MACH_NEC_ROCKHOPPER: return "NEC Rockhopper";
- case MACH_NEC_ROCKHOPPERII: return "NEC RockhopperII";
- default: return "Unknown NEC board";
- }
-}
-
-#if defined(CONFIG_DDB5477)
-void ddb5477_runtime_detection(void);
-#endif
-
-/* [jsun@junsun.net] PMON passes arguments in C main() style */
-void __init prom_init(void)
-{
- int argc = fw_arg0;
- char **arg = (char**) fw_arg1;
- int i;
-
- /* if user passes kernel args, ignore the default one */
- if (argc > 1)
- arcs_cmdline[0] = '\0';
-
- /* arg[0] is "g", the rest is boot parameters */
- for (i = 1; i < argc; i++) {
- if (strlen(arcs_cmdline) + strlen(arg[i] + 1)
- >= sizeof(arcs_cmdline))
- break;
- strcat(arcs_cmdline, arg[i]);
- strcat(arcs_cmdline, " ");
- }
-
- mips_machgroup = MACH_GROUP_NEC_DDB;
-
-#if defined(CONFIG_DDB5477)
- ddb5477_runtime_detection();
- add_memory_region(0, board_ram_size, BOOT_MEM_RAM);
-#endif
-}
-
-void __init prom_free_prom_memory(void)
-{
-}
-
-#if defined(CONFIG_DDB5477)
-
-#define DEFAULT_LCS1_BASE 0x19000000
-#define TESTVAL1 'K'
-#define TESTVAL2 'S'
-
-int board_ram_size;
-void ddb5477_runtime_detection(void)
-{
- volatile char *test_offset;
- char saved_test_byte;
-
- /* Determine if this is a DDB5477 board, or a BSB-VR0300
- base board. We can tell by checking for the location of
- the NVRAM. It lives at the beginning of LCS1 on the DDB5477,
- and the beginning of LCS1 on the BSB-VR0300 is flash memory.
- The first 2K of the NVRAM are reserved, so don't we'll poke
- around just after that.
- */
-
- /* We can only use the PCI bus to distinquish between
- the Rockhopper and RockhopperII backplanes and this must
- wait until ddb5477_board_init() in setup.c after the 5477
- is initialized. So, until then handle
- both Rockhopper and RockhopperII backplanes as Rockhopper 1
- */
-
- test_offset = (char *)KSEG1ADDR(DEFAULT_LCS1_BASE + 0x800);
- saved_test_byte = *test_offset;
-
- *test_offset = TESTVAL1;
- if (*test_offset != TESTVAL1) {
- /* We couldn't set our test value, so it must not be NVRAM,
- so it's a BSB_VR0300 */
- mips_machtype = MACH_NEC_ROCKHOPPER;
- } else {
- /* We may have gotten lucky, and the TESTVAL1 was already
- stored at the test location, so we must check a second
- test value */
- *test_offset = TESTVAL2;
- if (*test_offset != TESTVAL2) {
- /* OK, we couldn't set this value either, so it must
- definately be a BSB_VR0300 */
- mips_machtype = MACH_NEC_ROCKHOPPER;
- } else {
- /* We could change the value twice, so it must be
- NVRAM, so it's a DDB_VRC5477 */
- mips_machtype = MACH_NEC_DDB5477;
- }
- }
- /* Restore the original byte */
- *test_offset = saved_test_byte;
-
- /* before we know a better way, we will trust PMON for getting
- * RAM size
- */
- board_ram_size = 1 << (36 - (ddb_in32(DDB_SDRAM0) & 0xf));
-
- db_run(printk("DDB run-time detection : %s, %d MB RAM\n",
- mips_machtype == MACH_NEC_DDB5477 ?
- "DDB5477" : "Rockhopper",
- board_ram_size >> 20));
-
- /* we can't handle ram size > 128 MB */
- db_assert(board_ram_size <= (128 << 20));
-}
-#endif
+++ /dev/null
-/*
- * Copyright 2001 MontaVista Software Inc.
- * Author: jsun@mvista.com or jsun@junsun.net
- *
- * arch/mips/ddb5xxx/common/rtc_ds1386.c
- * low-level RTC hookups for s for Dallas 1396 chip.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- */
-
-
-/*
- * This file exports a function, rtc_ds1386_init(), which expects an
- * uncached base address as the argument. It will set the two function
- * pointers expected by the MIPS generic timer code.
- */
-
-#include <linux/types.h>
-#include <linux/time.h>
-#include <linux/bcd.h>
-
-#include <asm/time.h>
-#include <asm/addrspace.h>
-
-#include <asm/mc146818rtc.h>
-#include <asm/debug.h>
-
-#define EPOCH 2000
-
-#define READ_RTC(x) *(volatile unsigned char*)(rtc_base+x)
-#define WRITE_RTC(x, y) *(volatile unsigned char*)(rtc_base+x) = y
-
-static unsigned long rtc_base;
-
-static unsigned long
-rtc_ds1386_get_time(void)
-{
- u8 byte;
- u8 temp;
- unsigned int year, month, day, hour, minute, second;
- unsigned long flags;
-
- spin_lock_irqsave(&rtc_lock, flags);
- /* let us freeze external registers */
- byte = READ_RTC(0xB);
- byte &= 0x3f;
- WRITE_RTC(0xB, byte);
-
- /* read time data */
- year = BCD2BIN(READ_RTC(0xA)) + EPOCH;
- month = BCD2BIN(READ_RTC(0x9) & 0x1f);
- day = BCD2BIN(READ_RTC(0x8));
- minute = BCD2BIN(READ_RTC(0x2));
- second = BCD2BIN(READ_RTC(0x1));
-
- /* hour is special - deal with it later */
- temp = READ_RTC(0x4);
-
- /* enable time transfer */
- byte |= 0x80;
- WRITE_RTC(0xB, byte);
- spin_unlock_irqrestore(&rtc_lock, flags);
-
- /* calc hour */
- if (temp & 0x40) {
- /* 12 hour format */
- hour = BCD2BIN(temp & 0x1f);
- if (temp & 0x20) hour += 12; /* PM */
- } else {
- /* 24 hour format */
- hour = BCD2BIN(temp & 0x3f);
- }
-
- return mktime(year, month, day, hour, minute, second);
-}
-
-static int
-rtc_ds1386_set_time(unsigned long t)
-{
- struct rtc_time tm;
- u8 byte;
- u8 temp;
- u8 year, month, day, hour, minute, second;
- unsigned long flags;
-
- spin_lock_irqsave(&rtc_lock, flags);
- /* let us freeze external registers */
- byte = READ_RTC(0xB);
- byte &= 0x3f;
- WRITE_RTC(0xB, byte);
-
- /* convert */
- to_tm(t, &tm);
-
-
- /* check each field one by one */
- year = BIN2BCD(tm.tm_year - EPOCH);
- if (year != READ_RTC(0xA)) {
- WRITE_RTC(0xA, year);
- }
-
- temp = READ_RTC(0x9);
- month = BIN2BCD(tm.tm_mon+1); /* tm_mon starts from 0 to 11 */
- if (month != (temp & 0x1f)) {
- WRITE_RTC( 0x9,
- (month & 0x1f) | (temp & ~0x1f) );
- }
-
- day = BIN2BCD(tm.tm_mday);
- if (day != READ_RTC(0x8)) {
- WRITE_RTC(0x8, day);
- }
-
- temp = READ_RTC(0x4);
- if (temp & 0x40) {
- /* 12 hour format */
- hour = 0x40;
- if (tm.tm_hour > 12) {
- hour |= 0x20 | (BIN2BCD(hour-12) & 0x1f);
- } else {
- hour |= BIN2BCD(tm.tm_hour);
- }
- } else {
- /* 24 hour format */
- hour = BIN2BCD(tm.tm_hour) & 0x3f;
- }
- if (hour != temp) WRITE_RTC(0x4, hour);
-
- minute = BIN2BCD(tm.tm_min);
- if (minute != READ_RTC(0x2)) {
- WRITE_RTC(0x2, minute);
- }
-
- second = BIN2BCD(tm.tm_sec);
- if (second != READ_RTC(0x1)) {
- WRITE_RTC(0x1, second);
- }
- spin_unlock_irqrestore(&rtc_lock, flags);
-
- return 0;
-}
-
-void
-rtc_ds1386_init(unsigned long base)
-{
- unsigned char byte;
-
- /* remember the base */
- rtc_base = base;
- db_assert((rtc_base & 0xe0000000) == KSEG1);
-
- /* turn on RTC if it is not on */
- byte = READ_RTC(0x9);
- if (byte & 0x80) {
- byte &= 0x7f;
- WRITE_RTC(0x9, byte);
- }
-
- /* enable time transfer */
- byte = READ_RTC(0xB);
- byte |= 0x80;
- WRITE_RTC(0xB, byte);
-
- /* set the function pointers */
- rtc_mips_get_time = rtc_ds1386_get_time;
- rtc_mips_set_time = rtc_ds1386_set_time;
-}
+++ /dev/null
-#
-# Makefile for NEC DDB-Vrc5477 board
-#
-
-obj-y += ddb5477-platform.o irq.o irq_5477.o setup.o \
- lcd44780.o
-
-obj-$(CONFIG_RUNTIME_DEBUG) += debug.o
-obj-$(CONFIG_KGDB) += kgdb_io.o
-
-EXTRA_CFLAGS += -Werror
+++ /dev/null
-/*
- * This file is subject to the terms and conditions of the GNU General Public
- * License. See the file "COPYING" in the main directory of this archive
- * for more details.
- *
- * Copyright (C) 2007 Ralf Baechle (ralf@linux-mips.org)
- */
-#include <linux/init.h>
-#include <linux/module.h>
-#include <linux/serial_8250.h>
-
-#include <asm/ddb5xxx/ddb5477.h>
-
-#define DDB_UART_FLAGS (UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_IOREMAP)
-
-#define DDB5477_PORT(base, int) \
-{ \
- .mapbase = base, \
- .irq = int, \
- .uartclk = 1843200, \
- .iotype = UPIO_MEM, \
- .flags = DDB_UART_FLAGS, \
- .regshift = 3, \
-}
-
-static struct plat_serial8250_port uart8250_data[] = {
- DDB5477_PORT(0xbfa04200, VRC5477_IRQ_UART0),
- DDB5477_PORT(0xbfa04240, VRC5477_IRQ_UART1),
- { },
-};
-
-static struct platform_device uart8250_device = {
- .name = "serial8250",
- .id = PLAT8250_DEV_PLATFORM,
- .dev = {
- .platform_data = uart8250_data,
- },
-};
-
-static int __init uart8250_init(void)
-{
- return platform_device_register(&uart8250_device);
-}
-
-module_init(uart8250_init);
-
-MODULE_AUTHOR("Ralf Baechle <ralf@linux-mips.org>");
-MODULE_LICENSE("GPL");
-MODULE_DESCRIPTION("8250 UART probe driver for the NEC DDB5477");
+++ /dev/null
-/***********************************************************************
- *
- * Copyright 2001 MontaVista Software Inc.
- * Author: jsun@mvista.com or jsun@junsun.net
- *
- * arch/mips/ddb5xxx/ddb5477/debug.c
- * vrc5477 specific debug routines.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- ***********************************************************************
- */
-
-#include <linux/kernel.h>
-
-#include <asm/mipsregs.h>
-#include <asm/ddb5xxx/ddb5xxx.h>
-
-typedef struct {
- const char *regname;
- unsigned regaddr;
-} Register;
-
-void jsun_show_regs(char *name, Register *regs)
-{
- int i;
-
- printk("\nshow regs: %s\n", name);
- for(i=0;regs[i].regname!= NULL; i++) {
- printk("%-16s= %08x\t\t(@%08x)\n",
- regs[i].regname,
- *(unsigned *)(regs[i].regaddr),
- regs[i].regaddr);
- }
-}
-
-static Register int_regs[] = {
- {"DDB_INTCTRL0", DDB_BASE + DDB_INTCTRL0},
- {"DDB_INTCTRL1", DDB_BASE + DDB_INTCTRL1},
- {"DDB_INTCTRL2", DDB_BASE + DDB_INTCTRL2},
- {"DDB_INTCTRL3", DDB_BASE + DDB_INTCTRL3},
- {"DDB_INT0STAT", DDB_BASE + DDB_INT0STAT},
- {"DDB_INT1STAT", DDB_BASE + DDB_INT1STAT},
- {"DDB_INT2STAT", DDB_BASE + DDB_INT2STAT},
- {"DDB_INT3STAT", DDB_BASE + DDB_INT3STAT},
- {"DDB_INT4STAT", DDB_BASE + DDB_INT4STAT},
- {"DDB_NMISTAT", DDB_BASE + DDB_NMISTAT},
- {"DDB_INTPPES0", DDB_BASE + DDB_INTPPES0},
- {"DDB_INTPPES1", DDB_BASE + DDB_INTPPES1},
- {NULL, 0x0}
-};
-
-void vrc5477_show_int_regs()
-{
- jsun_show_regs("interrupt registers", int_regs);
- printk("CPU CAUSE = %08x\n", read_c0_cause());
- printk("CPU STATUS = %08x\n", read_c0_status());
-}
-static Register pdar_regs[] = {
- {"DDB_SDRAM0", DDB_BASE + DDB_SDRAM0},
- {"DDB_SDRAM1", DDB_BASE + DDB_SDRAM1},
- {"DDB_LCS0", DDB_BASE + DDB_LCS0},
- {"DDB_LCS1", DDB_BASE + DDB_LCS1},
- {"DDB_LCS2", DDB_BASE + DDB_LCS2},
- {"DDB_INTCS", DDB_BASE + DDB_INTCS},
- {"DDB_BOOTCS", DDB_BASE + DDB_BOOTCS},
- {"DDB_PCIW0", DDB_BASE + DDB_PCIW0},
- {"DDB_PCIW1", DDB_BASE + DDB_PCIW1},
- {"DDB_IOPCIW0", DDB_BASE + DDB_IOPCIW0},
- {"DDB_IOPCIW1", DDB_BASE + DDB_IOPCIW1},
- {NULL, 0x0}
-};
-void vrc5477_show_pdar_regs(void)
-{
- jsun_show_regs("PDAR regs", pdar_regs);
-}
-
-static Register bar_regs[] = {
- {"DDB_BARC0", DDB_BASE + DDB_BARC0},
- {"DDB_BARM010", DDB_BASE + DDB_BARM010},
- {"DDB_BARM230", DDB_BASE + DDB_BARM230},
- {"DDB_BAR00", DDB_BASE + DDB_BAR00},
- {"DDB_BAR10", DDB_BASE + DDB_BAR10},
- {"DDB_BAR20", DDB_BASE + DDB_BAR20},
- {"DDB_BAR30", DDB_BASE + DDB_BAR30},
- {"DDB_BAR40", DDB_BASE + DDB_BAR40},
- {"DDB_BAR50", DDB_BASE + DDB_BAR50},
- {"DDB_BARB0", DDB_BASE + DDB_BARB0},
- {"DDB_BARC1", DDB_BASE + DDB_BARC1},
- {"DDB_BARM011", DDB_BASE + DDB_BARM011},
- {"DDB_BARM231", DDB_BASE + DDB_BARM231},
- {"DDB_BAR01", DDB_BASE + DDB_BAR01},
- {"DDB_BAR11", DDB_BASE + DDB_BAR11},
- {"DDB_BAR21", DDB_BASE + DDB_BAR21},
- {"DDB_BAR31", DDB_BASE + DDB_BAR31},
- {"DDB_BAR41", DDB_BASE + DDB_BAR41},
- {"DDB_BAR51", DDB_BASE + DDB_BAR51},
- {"DDB_BARB1", DDB_BASE + DDB_BARB1},
- {NULL, 0x0}
-};
-void vrc5477_show_bar_regs(void)
-{
- jsun_show_regs("BAR regs", bar_regs);
-}
-
-static Register pci_regs[] = {
- {"DDB_PCIW0", DDB_BASE + DDB_PCIW0},
- {"DDB_PCIW1", DDB_BASE + DDB_PCIW1},
- {"DDB_PCIINIT00", DDB_BASE + DDB_PCIINIT00},
- {"DDB_PCIINIT10", DDB_BASE + DDB_PCIINIT10},
- {"DDB_PCICTL0_L", DDB_BASE + DDB_PCICTL0_L},
- {"DDB_PCICTL0_H", DDB_BASE + DDB_PCICTL0_H},
- {"DDB_PCIARB0_L", DDB_BASE + DDB_PCIARB0_L},
- {"DDB_PCIARB0_H", DDB_BASE + DDB_PCIARB0_H},
- {"DDB_PCISWP0", DDB_BASE + DDB_PCISWP0},
- {"DDB_PCIERR0", DDB_BASE + DDB_PCIERR0},
- {"DDB_IOPCIW0", DDB_BASE + DDB_IOPCIW0},
- {"DDB_IOPCIW1", DDB_BASE + DDB_IOPCIW1},
- {"DDB_PCIINIT01", DDB_BASE + DDB_PCIINIT01},
- {"DDB_PCIINIT11", DDB_BASE + DDB_PCIINIT11},
- {"DDB_PCICTL1_L", DDB_BASE + DDB_PCICTL1_L},
- {"DDB_PCICTL1_H", DDB_BASE + DDB_PCICTL1_H},
- {"DDB_PCIARB1_L", DDB_BASE + DDB_PCIARB1_L},
- {"DDB_PCIARB1_H", DDB_BASE + DDB_PCIARB1_H},
- {"DDB_PCISWP1", DDB_BASE + DDB_PCISWP1},
- {"DDB_PCIERR1", DDB_BASE + DDB_PCIERR1},
- {NULL, 0x0}
-};
-void vrc5477_show_pci_regs(void)
-{
- jsun_show_regs("PCI regs", pci_regs);
-}
-
-static Register lb_regs[] = {
- {"DDB_LCNFG", DDB_BASE + DDB_LCNFG},
- {"DDB_LCST0", DDB_BASE + DDB_LCST0},
- {"DDB_LCST1", DDB_BASE + DDB_LCST1},
- {"DDB_LCST2", DDB_BASE + DDB_LCST2},
- {"DDB_ERRADR", DDB_BASE + DDB_ERRADR},
- {"DDB_ERRCS", DDB_BASE + DDB_ERRCS},
- {"DDB_BTM", DDB_BASE + DDB_BTM},
- {"DDB_BCST", DDB_BASE + DDB_BCST},
- {NULL, 0x0}
-};
-void vrc5477_show_lb_regs(void)
-{
- jsun_show_regs("Local Bus regs", lb_regs);
-}
-
-void vrc5477_show_all_regs(void)
-{
- vrc5477_show_pdar_regs();
- vrc5477_show_pci_regs();
- vrc5477_show_bar_regs();
- vrc5477_show_int_regs();
- vrc5477_show_lb_regs();
-}
+++ /dev/null
-/*
- * Copyright 2001 MontaVista Software Inc.
- * Author: Jun Sun, jsun@mvista.com or jsun@junsun.net
- *
- * arch/mips/ddb5xxx/ddb5477/irq.c
- * The irq setup and misc routines for DDB5476.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- */
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/irq.h>
-#include <linux/types.h>
-#include <linux/ptrace.h>
-
-#include <asm/i8259.h>
-#include <asm/irq_cpu.h>
-#include <asm/system.h>
-#include <asm/mipsregs.h>
-#include <asm/debug.h>
-#include <asm/addrspace.h>
-#include <asm/bootinfo.h>
-
-#include <asm/ddb5xxx/ddb5xxx.h>
-
-
-/*
- * IRQ mapping
- *
- * 0-7: 8 CPU interrupts
- * 0 - software interrupt 0
- * 1 - software interrupt 1
- * 2 - most Vrc5477 interrupts are routed to this pin
- * 3 - (optional) some other interrupts routed to this pin for debugg
- * 4 - not used
- * 5 - not used
- * 6 - not used
- * 7 - cpu timer (used by default)
- *
- * 8-39: 32 Vrc5477 interrupt sources
- * (refer to the Vrc5477 manual)
- */
-
-#define PCI0 DDB_INTPPES0
-#define PCI1 DDB_INTPPES1
-
-#define ACTIVE_LOW 1
-#define ACTIVE_HIGH 0
-
-#define LEVEL_SENSE 2
-#define EDGE_TRIGGER 0
-
-#define INTA 0
-#define INTB 1
-#define INTC 2
-#define INTD 3
-#define INTE 4
-
-static inline void
-set_pci_int_attr(u32 pci, u32 intn, u32 active, u32 trigger)
-{
- u32 reg_value;
- u32 reg_bitmask;
-
- reg_value = ddb_in32(pci);
- reg_bitmask = 0x3 << (intn * 2);
-
- reg_value &= ~reg_bitmask;
- reg_value |= (active | trigger) << (intn * 2);
- ddb_out32(pci, reg_value);
-}
-
-extern void vrc5477_irq_init(u32 base);
-static struct irqaction irq_cascade = { no_action, 0, CPU_MASK_NONE, "cascade", NULL, NULL };
-
-void __init arch_init_irq(void)
-{
- /* by default, we disable all interrupts and route all vrc5477
- * interrupts to pin 0 (irq 2) */
- ddb_out32(DDB_INTCTRL0, 0);
- ddb_out32(DDB_INTCTRL1, 0);
- ddb_out32(DDB_INTCTRL2, 0);
- ddb_out32(DDB_INTCTRL3, 0);
-
- clear_c0_status(0xff00);
- set_c0_status(0x0400);
-
- /* setup PCI interrupt attributes */
- set_pci_int_attr(PCI0, INTA, ACTIVE_LOW, LEVEL_SENSE);
- set_pci_int_attr(PCI0, INTB, ACTIVE_LOW, LEVEL_SENSE);
- if (mips_machtype == MACH_NEC_ROCKHOPPERII)
- set_pci_int_attr(PCI0, INTC, ACTIVE_HIGH, LEVEL_SENSE);
- else
- set_pci_int_attr(PCI0, INTC, ACTIVE_LOW, LEVEL_SENSE);
- set_pci_int_attr(PCI0, INTD, ACTIVE_LOW, LEVEL_SENSE);
- set_pci_int_attr(PCI0, INTE, ACTIVE_LOW, LEVEL_SENSE);
-
- set_pci_int_attr(PCI1, INTA, ACTIVE_LOW, LEVEL_SENSE);
- set_pci_int_attr(PCI1, INTB, ACTIVE_LOW, LEVEL_SENSE);
- set_pci_int_attr(PCI1, INTC, ACTIVE_LOW, LEVEL_SENSE);
- set_pci_int_attr(PCI1, INTD, ACTIVE_LOW, LEVEL_SENSE);
- set_pci_int_attr(PCI1, INTE, ACTIVE_LOW, LEVEL_SENSE);
-
- /*
- * for debugging purpose, we enable several error interrupts
- * and route them to pin 1. (IP3)
- */
- /* cpu parity check - 0 */
- ll_vrc5477_irq_route(0, 1); ll_vrc5477_irq_enable(0);
- /* cpu no-target decode - 1 */
- ll_vrc5477_irq_route(1, 1); ll_vrc5477_irq_enable(1);
- /* local bus read time-out - 7 */
- ll_vrc5477_irq_route(7, 1); ll_vrc5477_irq_enable(7);
- /* PCI SERR# - 14 */
- ll_vrc5477_irq_route(14, 1); ll_vrc5477_irq_enable(14);
- /* PCI internal error - 15 */
- ll_vrc5477_irq_route(15, 1); ll_vrc5477_irq_enable(15);
- /* IOPCI SERR# - 30 */
- ll_vrc5477_irq_route(30, 1); ll_vrc5477_irq_enable(30);
- /* IOPCI internal error - 31 */
- ll_vrc5477_irq_route(31, 1); ll_vrc5477_irq_enable(31);
-
- /* init all controllers */
- init_i8259_irqs();
- mips_cpu_irq_init();
- vrc5477_irq_init(VRC5477_IRQ_BASE);
-
-
- /* setup cascade interrupts */
- setup_irq(VRC5477_IRQ_BASE + VRC5477_I8259_CASCADE, &irq_cascade);
- setup_irq(CPU_IRQ_BASE + CPU_VRC5477_CASCADE, &irq_cascade);
-}
-
-u8 i8259_interrupt_ack(void)
-{
- u8 irq;
- u32 reg;
-
- /* Set window 0 for interrupt acknowledge */
- reg = ddb_in32(DDB_PCIINIT10);
-
- ddb_set_pmr(DDB_PCIINIT10, DDB_PCICMD_IACK, 0, DDB_PCI_ACCESS_32);
- irq = *(volatile u8 *) KSEG1ADDR(DDB_PCI_IACK_BASE);
- ddb_out32(DDB_PCIINIT10, reg);
-
- return irq;
-}
-/*
- * the first level int-handler will jump here if it is a vrc5477 irq
- */
-#define NUM_5477_IRQS 32
-static void vrc5477_irq_dispatch(void)
-{
- u32 intStatus;
- u32 bitmask;
- u32 i;
-
- db_assert(ddb_in32(DDB_INT2STAT) == 0);
- db_assert(ddb_in32(DDB_INT3STAT) == 0);
- db_assert(ddb_in32(DDB_INT4STAT) == 0);
- db_assert(ddb_in32(DDB_NMISTAT) == 0);
-
- if (ddb_in32(DDB_INT1STAT) != 0) {
-#if defined(CONFIG_RUNTIME_DEBUG)
- vrc5477_show_int_regs();
-#endif
- panic("error interrupt has happened.");
- }
-
- intStatus = ddb_in32(DDB_INT0STAT);
-
- if (mips_machtype == MACH_NEC_ROCKHOPPERII) {
- /* check for i8259 interrupts */
- if (intStatus & (1 << VRC5477_I8259_CASCADE)) {
- int i8259_irq = i8259_interrupt_ack();
- do_IRQ(i8259_irq);
- return;
- }
- }
-
- for (i=0, bitmask=1; i<= NUM_5477_IRQS; bitmask <<=1, i++) {
- /* do we need to "and" with the int mask? */
- if (intStatus & bitmask) {
- do_IRQ(VRC5477_IRQ_BASE + i);
- return;
- }
- }
-}
-
-#define VR5477INTS (STATUSF_IP2|STATUSF_IP3|STATUSF_IP4|STATUSF_IP5|STATUSF_IP6)
-
-asmlinkage void plat_irq_dispatch(void)
-{
- unsigned int pending = read_c0_cause() & read_c0_status() & ST0_IM;
-
- if (pending & STATUSF_IP7)
- do_IRQ(CPU_IRQ_BASE + 7);
- else if (pending & VR5477INTS)
- vrc5477_irq_dispatch();
- else if (pending & STATUSF_IP0)
- do_IRQ(CPU_IRQ_BASE);
- else if (pending & STATUSF_IP1)
- do_IRQ(CPU_IRQ_BASE + 1);
- else
- spurious_interrupt();
-}
+++ /dev/null
-/*
- * Copyright 2001 MontaVista Software Inc.
- * Author: Jun Sun, jsun@mvista.com or jsun@junsun.net
- *
- * arch/mips/ddb5xxx/ddb5477/irq_5477.c
- * This file defines the irq handler for Vrc5477.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- */
-
-/*
- * Vrc5477 defines 32 IRQs.
- *
- * This file exports one function:
- * vrc5477_irq_init(u32 irq_base);
- */
-
-#include <linux/interrupt.h>
-#include <linux/types.h>
-#include <linux/ptrace.h>
-
-#include <asm/debug.h>
-
-#include <asm/ddb5xxx/ddb5xxx.h>
-
-/* number of total irqs supported by Vrc5477 */
-#define NUM_5477_IRQ 32
-
-static int vrc5477_irq_base = -1;
-
-
-static void
-vrc5477_irq_enable(unsigned int irq)
-{
- db_assert(vrc5477_irq_base != -1);
- db_assert(irq >= vrc5477_irq_base);
- db_assert(irq < vrc5477_irq_base+ NUM_5477_IRQ);
-
- ll_vrc5477_irq_enable(irq - vrc5477_irq_base);
-}
-
-static void
-vrc5477_irq_disable(unsigned int irq)
-{
- db_assert(vrc5477_irq_base != -1);
- db_assert(irq >= vrc5477_irq_base);
- db_assert(irq < vrc5477_irq_base + NUM_5477_IRQ);
-
- ll_vrc5477_irq_disable(irq - vrc5477_irq_base);
-}
-
-static void
-vrc5477_irq_ack(unsigned int irq)
-{
- db_assert(vrc5477_irq_base != -1);
- db_assert(irq >= vrc5477_irq_base);
- db_assert(irq < vrc5477_irq_base+ NUM_5477_IRQ);
-
- /* clear the interrupt bit */
- /* some irqs require the driver to clear the sources */
- ddb_out32(DDB_INTCLR32, 1 << (irq - vrc5477_irq_base));
-
- /* disable interrupt - some handler will re-enable the irq
- * and if the interrupt is leveled, we will have infinite loop
- */
- ll_vrc5477_irq_disable(irq - vrc5477_irq_base);
-}
-
-static void
-vrc5477_irq_end(unsigned int irq)
-{
- db_assert(vrc5477_irq_base != -1);
- db_assert(irq >= vrc5477_irq_base);
- db_assert(irq < vrc5477_irq_base + NUM_5477_IRQ);
-
- if(!(irq_desc[irq].status & (IRQ_DISABLED | IRQ_INPROGRESS)))
- ll_vrc5477_irq_enable( irq - vrc5477_irq_base);
-}
-
-struct irq_chip vrc5477_irq_controller = {
- .name = "vrc5477_irq",
- .ack = vrc5477_irq_ack,
- .mask = vrc5477_irq_disable,
- .mask_ack = vrc5477_irq_ack,
- .unmask = vrc5477_irq_enable,
- .end = vrc5477_irq_end
-};
-
-void __init vrc5477_irq_init(u32 irq_base)
-{
- u32 i;
-
- for (i= irq_base; i< irq_base+ NUM_5477_IRQ; i++)
- set_irq_chip(i, &vrc5477_irq_controller);
-
- vrc5477_irq_base = irq_base;
-}
-
-void ll_vrc5477_irq_route(int vrc5477_irq, int ip)
-{
- u32 reg_value;
- u32 reg_bitmask;
- u32 reg_index;
-
- db_assert(vrc5477_irq >= 0);
- db_assert(vrc5477_irq < NUM_5477_IRQ);
- db_assert(ip >= 0);
- db_assert((ip < 5) || (ip == 6));
-
- reg_index = DDB_INTCTRL0 + vrc5477_irq/8*4;
- reg_value = ddb_in32(reg_index);
- reg_bitmask = 7 << (vrc5477_irq % 8 * 4);
- reg_value &= ~reg_bitmask;
- reg_value |= ip << (vrc5477_irq % 8 * 4);
- ddb_out32(reg_index, reg_value);
-}
-
-void ll_vrc5477_irq_enable(int vrc5477_irq)
-{
- u32 reg_value;
- u32 reg_bitmask;
- u32 reg_index;
-
- db_assert(vrc5477_irq >= 0);
- db_assert(vrc5477_irq < NUM_5477_IRQ);
-
- reg_index = DDB_INTCTRL0 + vrc5477_irq/8*4;
- reg_value = ddb_in32(reg_index);
- reg_bitmask = 8 << (vrc5477_irq % 8 * 4);
- db_assert((reg_value & reg_bitmask) == 0);
- ddb_out32(reg_index, reg_value | reg_bitmask);
-}
-
-void ll_vrc5477_irq_disable(int vrc5477_irq)
-{
- u32 reg_value;
- u32 reg_bitmask;
- u32 reg_index;
-
- db_assert(vrc5477_irq >= 0);
- db_assert(vrc5477_irq < NUM_5477_IRQ);
-
- reg_index = DDB_INTCTRL0 + vrc5477_irq/8*4;
- reg_value = ddb_in32(reg_index);
- reg_bitmask = 8 << (vrc5477_irq % 8 * 4);
-
- /* we assert that the interrupt is enabled (perhaps over-zealous) */
- db_assert( (reg_value & reg_bitmask) != 0);
- ddb_out32(reg_index, reg_value & ~reg_bitmask);
-}
+++ /dev/null
-/*
- * kgdb io functions for DDB5477. We use the second serial port (upper one).
- *
- * Copyright (C) 2001 MontaVista Software Inc.
- * Author: jsun@mvista.com or jsun@junsun.net
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- */
-
-/* ======================= CONFIG ======================== */
-
-/* [jsun] we use the second serial port for kdb */
-#define BASE 0xbfa04240
-#define MAX_BAUD 115200
-
-/* distance in bytes between two serial registers */
-#define REG_OFFSET 8
-
-/*
- * 0 - kgdb does serial init
- * 1 - kgdb skip serial init
- */
-static int remoteDebugInitialized = 0;
-
-/*
- * the default baud rate *if* kgdb does serial init
- */
-#define BAUD_DEFAULT UART16550_BAUD_38400
-
-/* ======================= END OF CONFIG ======================== */
-
-typedef unsigned char uint8;
-typedef unsigned int uint32;
-
-#define UART16550_BAUD_2400 2400
-#define UART16550_BAUD_4800 4800
-#define UART16550_BAUD_9600 9600
-#define UART16550_BAUD_19200 19200
-#define UART16550_BAUD_38400 38400
-#define UART16550_BAUD_57600 57600
-#define UART16550_BAUD_115200 115200
-
-#define UART16550_PARITY_NONE 0
-#define UART16550_PARITY_ODD 0x08
-#define UART16550_PARITY_EVEN 0x18
-#define UART16550_PARITY_MARK 0x28
-#define UART16550_PARITY_SPACE 0x38
-
-#define UART16550_DATA_5BIT 0x0
-#define UART16550_DATA_6BIT 0x1
-#define UART16550_DATA_7BIT 0x2
-#define UART16550_DATA_8BIT 0x3
-
-#define UART16550_STOP_1BIT 0x0
-#define UART16550_STOP_2BIT 0x4
-
-/* register offset */
-#define OFS_RCV_BUFFER 0
-#define OFS_TRANS_HOLD 0
-#define OFS_SEND_BUFFER 0
-#define OFS_INTR_ENABLE (1*REG_OFFSET)
-#define OFS_INTR_ID (2*REG_OFFSET)
-#define OFS_DATA_FORMAT (3*REG_OFFSET)
-#define OFS_LINE_CONTROL (3*REG_OFFSET)
-#define OFS_MODEM_CONTROL (4*REG_OFFSET)
-#define OFS_RS232_OUTPUT (4*REG_OFFSET)
-#define OFS_LINE_STATUS (5*REG_OFFSET)
-#define OFS_MODEM_STATUS (6*REG_OFFSET)
-#define OFS_RS232_INPUT (6*REG_OFFSET)
-#define OFS_SCRATCH_PAD (7*REG_OFFSET)
-
-#define OFS_DIVISOR_LSB (0*REG_OFFSET)
-#define OFS_DIVISOR_MSB (1*REG_OFFSET)
-
-
-/* memory-mapped read/write of the port */
-#define UART16550_READ(y) (*((volatile uint8*)(BASE + y)))
-#define UART16550_WRITE(y, z) ((*((volatile uint8*)(BASE + y))) = z)
-
-void debugInit(uint32 baud, uint8 data, uint8 parity, uint8 stop)
-{
- /* disable interrupts */
- UART16550_WRITE(OFS_INTR_ENABLE, 0);
-
- /* set up baud rate */
- {
- uint32 divisor;
-
- /* set DIAB bit */
- UART16550_WRITE(OFS_LINE_CONTROL, 0x80);
-
- /* set divisor */
- divisor = MAX_BAUD / baud;
- UART16550_WRITE(OFS_DIVISOR_LSB, divisor & 0xff);
- UART16550_WRITE(OFS_DIVISOR_MSB, (divisor & 0xff00) >> 8);
-
- /* clear DIAB bit */
- UART16550_WRITE(OFS_LINE_CONTROL, 0x0);
- }
-
- /* set data format */
- UART16550_WRITE(OFS_DATA_FORMAT, data | parity | stop);
-}
-
-
-uint8 getDebugChar(void)
-{
- if (!remoteDebugInitialized) {
- remoteDebugInitialized = 1;
- debugInit(BAUD_DEFAULT,
- UART16550_DATA_8BIT,
- UART16550_PARITY_NONE, UART16550_STOP_1BIT);
- }
-
- while ((UART16550_READ(OFS_LINE_STATUS) & 0x1) == 0);
- return UART16550_READ(OFS_RCV_BUFFER);
-}
-
-
-int putDebugChar(uint8 byte)
-{
- if (!remoteDebugInitialized) {
- remoteDebugInitialized = 1;
- debugInit(BAUD_DEFAULT,
- UART16550_DATA_8BIT,
- UART16550_PARITY_NONE, UART16550_STOP_1BIT);
- }
-
- while ((UART16550_READ(OFS_LINE_STATUS) & 0x20) == 0);
- UART16550_WRITE(OFS_SEND_BUFFER, byte);
- return 1;
-}
+++ /dev/null
-/*
- * lcd44780.c
- * Simple "driver" for a memory-mapped 44780-style LCD display.
- *
- * Copyright 2001 Bradley D. LaRonde <brad@ltc.com>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- */
-
-#define LCD44780_COMMAND ((volatile unsigned char *)0xbe020000)
-#define LCD44780_DATA ((volatile unsigned char *)0xbe020001)
-
-#define LCD44780_4BIT_1LINE 0x20
-#define LCD44780_4BIT_2LINE 0x28
-#define LCD44780_8BIT_1LINE 0x30
-#define LCD44780_8BIT_2LINE 0x38
-#define LCD44780_MODE_DEC 0x04
-#define LCD44780_MODE_DEC_SHIFT 0x05
-#define LCD44780_MODE_INC 0x06
-#define LCD44780_MODE_INC_SHIFT 0x07
-#define LCD44780_SCROLL_LEFT 0x18
-#define LCD44780_SCROLL_RIGHT 0x1e
-#define LCD44780_CURSOR_UNDERLINE 0x0e
-#define LCD44780_CURSOR_BLOCK 0x0f
-#define LCD44780_CURSOR_OFF 0x0c
-#define LCD44780_CLEAR 0x01
-#define LCD44780_BLANK 0x08
-#define LCD44780_RESTORE 0x0c // Same as CURSOR_OFF
-#define LCD44780_HOME 0x02
-#define LCD44780_LEFT 0x10
-#define LCD44780_RIGHT 0x14
-
-void lcd44780_wait(void)
-{
- int i, j;
- for(i=0; i < 400; i++)
- for(j=0; j < 10000; j++);
-}
-
-void lcd44780_command(unsigned char c)
-{
- *LCD44780_COMMAND = c;
- lcd44780_wait();
-}
-
-void lcd44780_data(unsigned char c)
-{
- *LCD44780_DATA = c;
- lcd44780_wait();
-}
-
-void lcd44780_puts(const char* s)
-{
- int j;
- int pos = 0;
-
- lcd44780_command(LCD44780_CLEAR);
- while(*s) {
- lcd44780_data(*s);
- s++;
- pos++;
- if (pos == 8) {
- /* We must write 32 of spaces to get cursor to 2nd line */
- for (j=0; j<32; j++) {
- lcd44780_data(' ');
- }
- }
- if (pos == 16) {
- /* We have filled all 16 character positions, so stop
- outputing data */
- break;
- }
- }
-#ifdef LCD44780_PUTS_PAUSE
- {
- int i;
-
- for(i = 1; i < 2000; i++)
- lcd44780_wait();
- }
-#endif
-}
-
-void lcd44780_init(void)
-{
- // The display on the RockHopper is physically a single
- // 16 char line (two 8 char lines concatenated). bdl
- lcd44780_command(LCD44780_8BIT_2LINE);
- lcd44780_command(LCD44780_MODE_INC);
- lcd44780_command(LCD44780_CURSOR_BLOCK);
- lcd44780_command(LCD44780_CLEAR);
-}
+++ /dev/null
-/*
- * lcd44780.h
- * Simple "driver" for a memory-mapped 44780-style LCD display.
- *
- * Copyright 2001 Bradley D. LaRonde <brad@ltc.com>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- */
-
-void lcd44780_puts(const char* s);
-void lcd44780_init(void);
+++ /dev/null
-/*
- *
- * Copyright 2001 MontaVista Software Inc.
- * Author: jsun@mvista.com or jsun@junsun.net
- *
- * Copyright (C) 2004 by Ralf Baechle (ralf@linux-mips.org)
- *
- * arch/mips/ddb5xxx/ddb5477/setup.c
- * Setup file for DDB5477.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- */
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <linux/types.h>
-#include <linux/sched.h>
-#include <linux/pci.h>
-#include <linux/ide.h>
-#include <linux/irq.h>
-#include <linux/fs.h>
-#include <linux/ioport.h>
-#include <linux/param.h> /* for HZ */
-#include <linux/major.h>
-#include <linux/kdev_t.h>
-#include <linux/root_dev.h>
-#include <linux/pm.h>
-
-#include <asm/cpu.h>
-#include <asm/bootinfo.h>
-#include <asm/addrspace.h>
-#include <asm/time.h>
-#include <asm/bcache.h>
-#include <asm/irq.h>
-#include <asm/reboot.h>
-#include <asm/gdb-stub.h>
-#include <asm/traps.h>
-#include <asm/debug.h>
-
-#include <asm/ddb5xxx/ddb5xxx.h>
-
-#include "lcd44780.h"
-
-
-#define USE_CPU_COUNTER_TIMER /* whether we use cpu counter */
-
-#define SP_TIMER_BASE DDB_SPT1CTRL_L
-#define SP_TIMER_IRQ VRC5477_IRQ_SPT1
-
-static int bus_frequency = CONFIG_DDB5477_BUS_FREQUENCY*1000;
-
-static void ddb_machine_restart(char *command)
-{
- static void (*back_to_prom) (void) = (void (*)(void)) 0xbfc00000;
-
- u32 t;
-
- /* PCI cold reset */
- ddb_pci_reset_bus();
-
- /* CPU cold reset */
- t = ddb_in32(DDB_CPUSTAT);
- db_assert((t&1));
- ddb_out32(DDB_CPUSTAT, t);
-
- /* Call the PROM */
- back_to_prom();
-}
-
-static void ddb_machine_halt(void)
-{
- printk("DDB Vrc-5477 halted.\n");
- while (1);
-}
-
-static void ddb_machine_power_off(void)
-{
- printk("DDB Vrc-5477 halted. Please turn off the power.\n");
- while (1);
-}
-
-extern void rtc_ds1386_init(unsigned long base);
-
-static unsigned int __init detect_bus_frequency(unsigned long rtc_base)
-{
- unsigned int freq;
- unsigned char c;
- unsigned int t1, t2;
- unsigned i;
-
- ddb_out32(SP_TIMER_BASE, 0xffffffff);
- ddb_out32(SP_TIMER_BASE+4, 0x1);
- ddb_out32(SP_TIMER_BASE+8, 0xffffffff);
-
- /* check if rtc is running */
- c= *(volatile unsigned char*)rtc_base;
- for(i=0; (c == *(volatile unsigned char*)rtc_base) && (i<100000000); i++);
- if (c == *(volatile unsigned char*)rtc_base) {
- printk("Failed to detect bus frequency. Use default 83.3MHz.\n");
- return 83333000;
- }
-
- c= *(volatile unsigned char*)rtc_base;
- while (c == *(volatile unsigned char*)rtc_base);
- /* we are now at the turn of 1/100th second, if no error. */
- t1 = ddb_in32(SP_TIMER_BASE+8);
-
- for (i=0; i< 10; i++) {
- c= *(volatile unsigned char*)rtc_base;
- while (c == *(volatile unsigned char*)rtc_base);
- /* we are now at the turn of another 1/100th second */
- t2 = ddb_in32(SP_TIMER_BASE+8);
- }
-
- ddb_out32(SP_TIMER_BASE+4, 0x0); /* disable it again */
-
- freq = (t1 - t2)*10;
- printk("DDB bus frequency detection : %u \n", freq);
- return freq;
-}
-
-static void __init ddb_time_init(void)
-{
- unsigned long rtc_base;
- unsigned int i;
-
- /* we have ds1396 RTC chip */
- if (mips_machtype == MACH_NEC_ROCKHOPPER
- || mips_machtype == MACH_NEC_ROCKHOPPERII) {
- rtc_base = KSEG1ADDR(DDB_LCS2_BASE);
- } else {
- rtc_base = KSEG1ADDR(DDB_LCS1_BASE);
- }
- rtc_ds1386_init(rtc_base);
-
- /* do we need to do run-time detection of bus speed? */
- if (bus_frequency == 0) {
- bus_frequency = detect_bus_frequency(rtc_base);
- }
-
- /* mips_hpt_frequency is 1/2 of the cpu core freq */
- i = (read_c0_config() >> 28 ) & 7;
- if ((current_cpu_data.cputype == CPU_R5432) && (i == 3))
- i = 4;
- mips_hpt_frequency = bus_frequency*(i+4)/4;
-}
-
-void __init plat_timer_setup(struct irqaction *irq)
-{
-#if defined(USE_CPU_COUNTER_TIMER)
-
- /* we are using the cpu counter for timer interrupts */
- setup_irq(CPU_IRQ_BASE + 7, irq);
-
-#else
-
- /* if we use Special purpose timer 1 */
- ddb_out32(SP_TIMER_BASE, bus_frequency/HZ);
- ddb_out32(SP_TIMER_BASE+4, 0x1);
- setup_irq(SP_TIMER_IRQ, irq);
-
-#endif
-}
-
-static void ddb5477_board_init(void);
-
-extern struct pci_controller ddb5477_ext_controller;
-extern struct pci_controller ddb5477_io_controller;
-
-void __init plat_mem_setup(void)
-{
- /* initialize board - we don't trust the loader */
- ddb5477_board_init();
-
- set_io_port_base(KSEG1ADDR(DDB_PCI_IO_BASE));
-
- board_time_init = ddb_time_init;
-
- _machine_restart = ddb_machine_restart;
- _machine_halt = ddb_machine_halt;
- pm_power_off = ddb_machine_power_off;
-
- /* setup resource limits */
- ioport_resource.end = DDB_PCI0_IO_SIZE + DDB_PCI1_IO_SIZE - 1;
- iomem_resource.end = 0xffffffff;
-
- /* Reboot on panic */
- panic_timeout = 180;
-
- register_pci_controller (&ddb5477_ext_controller);
- register_pci_controller (&ddb5477_io_controller);
-}
-
-static void __init ddb5477_board_init(void)
-{
- /* ----------- setup PDARs ------------ */
-
- /* SDRAM should have been set */
- db_assert(ddb_in32(DDB_SDRAM0) ==
- ddb_calc_pdar(DDB_SDRAM_BASE, board_ram_size, 32, 0, 1));
-
- /* SDRAM1 should be turned off. What is this for anyway ? */
- db_assert( (ddb_in32(DDB_SDRAM1) & 0xf) == 0);
-
- /* Setup local bus. */
-
- /* Flash U12 PDAR and timing. */
- ddb_set_pdar(DDB_LCS0, DDB_LCS0_BASE, DDB_LCS0_SIZE, 16, 0, 0);
- ddb_out32(DDB_LCST0, 0x00090842);
-
- /* We need to setup LCS1 and LCS2 differently based on the
- board_version */
- if (mips_machtype == MACH_NEC_ROCKHOPPER) {
- /* Flash U13 PDAR and timing. */
- ddb_set_pdar(DDB_LCS1, DDB_LCS1_BASE, DDB_LCS1_SIZE, 16, 0, 0);
- ddb_out32(DDB_LCST1, 0x00090842);
-
- /* EPLD (NVRAM, switch, LCD, and mezzanie). */
- ddb_set_pdar(DDB_LCS2, DDB_LCS2_BASE, DDB_LCS2_SIZE, 8, 0, 0);
- } else {
- /* misc */
- ddb_set_pdar(DDB_LCS1, DDB_LCS1_BASE, DDB_LCS1_SIZE, 8, 0, 0);
- /* mezzanie (?) */
- ddb_set_pdar(DDB_LCS2, DDB_LCS2_BASE, DDB_LCS2_SIZE, 16, 0, 0);
- }
-
- /* verify VRC5477 base addr */
- db_assert(ddb_in32(DDB_VRC5477) ==
- ddb_calc_pdar(DDB_VRC5477_BASE, DDB_VRC5477_SIZE, 32, 0, 1));
-
- /* verify BOOT ROM addr */
- db_assert(ddb_in32(DDB_BOOTCS) ==
- ddb_calc_pdar(DDB_BOOTCS_BASE, DDB_BOOTCS_SIZE, 8, 0, 0));
-
- /* setup PCI windows - window0 for MEM/config, window1 for IO */
- ddb_set_pdar(DDB_PCIW0, DDB_PCI0_MEM_BASE, DDB_PCI0_MEM_SIZE, 32, 0, 1);
- ddb_set_pdar(DDB_PCIW1, DDB_PCI0_IO_BASE, DDB_PCI0_IO_SIZE, 32, 0, 1);
- ddb_set_pdar(DDB_IOPCIW0, DDB_PCI1_MEM_BASE, DDB_PCI1_MEM_SIZE, 32, 0, 1);
- ddb_set_pdar(DDB_IOPCIW1, DDB_PCI1_IO_BASE, DDB_PCI1_IO_SIZE, 32, 0, 1);
-
- /* ------------ reset PCI bus and BARs ----------------- */
- ddb_pci_reset_bus();
-
- ddb_out32(DDB_BARM010, 0x00000008);
- ddb_out32(DDB_BARM011, 0x00000008);
-
- ddb_out32(DDB_BARC0, 0xffffffff);
- ddb_out32(DDB_BARM230, 0xffffffff);
- ddb_out32(DDB_BAR00, 0xffffffff);
- ddb_out32(DDB_BAR10, 0xffffffff);
- ddb_out32(DDB_BAR20, 0xffffffff);
- ddb_out32(DDB_BAR30, 0xffffffff);
- ddb_out32(DDB_BAR40, 0xffffffff);
- ddb_out32(DDB_BAR50, 0xffffffff);
- ddb_out32(DDB_BARB0, 0xffffffff);
-
- ddb_out32(DDB_BARC1, 0xffffffff);
- ddb_out32(DDB_BARM231, 0xffffffff);
- ddb_out32(DDB_BAR01, 0xffffffff);
- ddb_out32(DDB_BAR11, 0xffffffff);
- ddb_out32(DDB_BAR21, 0xffffffff);
- ddb_out32(DDB_BAR31, 0xffffffff);
- ddb_out32(DDB_BAR41, 0xffffffff);
- ddb_out32(DDB_BAR51, 0xffffffff);
- ddb_out32(DDB_BARB1, 0xffffffff);
-
- /*
- * We use pci master register 0 for memory space / config space
- * And we use register 1 for IO space.
- * Note that for memory space, we bump up the pci base address
- * so that we have 1:1 mapping between PCI memory and cpu physical.
- * For PCI IO space, it starts from 0 in PCI IO space but with
- * DDB_xx_IO_BASE in CPU physical address space.
- */
- ddb_set_pmr(DDB_PCIINIT00, DDB_PCICMD_MEM, DDB_PCI0_MEM_BASE,
- DDB_PCI_ACCESS_32);
- ddb_set_pmr(DDB_PCIINIT10, DDB_PCICMD_IO, 0, DDB_PCI_ACCESS_32);
-
- ddb_set_pmr(DDB_PCIINIT01, DDB_PCICMD_MEM, DDB_PCI1_MEM_BASE,
- DDB_PCI_ACCESS_32);
- ddb_set_pmr(DDB_PCIINIT11, DDB_PCICMD_IO, DDB_PCI0_IO_SIZE,
- DDB_PCI_ACCESS_32);
-
-
- /* PCI cross window should be set properly */
- ddb_set_pdar(DDB_BARP00, DDB_PCI1_MEM_BASE, DDB_PCI1_MEM_SIZE, 32, 0, 1);
- ddb_set_pdar(DDB_BARP10, DDB_PCI1_IO_BASE, DDB_PCI1_IO_SIZE, 32, 0, 1);
- ddb_set_pdar(DDB_BARP01, DDB_PCI0_MEM_BASE, DDB_PCI0_MEM_SIZE, 32, 0, 1);
- ddb_set_pdar(DDB_BARP11, DDB_PCI0_IO_BASE, DDB_PCI0_IO_SIZE, 32, 0, 1);
-
- if (mips_machtype == MACH_NEC_ROCKHOPPER
- || mips_machtype == MACH_NEC_ROCKHOPPERII) {
- /* Disable bus diagnostics. */
- ddb_out32(DDB_PCICTL0_L, 0);
- ddb_out32(DDB_PCICTL0_H, 0);
- ddb_out32(DDB_PCICTL1_L, 0);
- ddb_out32(DDB_PCICTL1_H, 0);
- }
-
- if (mips_machtype == MACH_NEC_ROCKHOPPER) {
- u16 vid;
- struct pci_bus bus;
- struct pci_dev dev_m1533;
- extern struct pci_ops ddb5477_ext_pci_ops;
-
- bus.parent = NULL; /* we scan the top level only */
- bus.ops = &ddb5477_ext_pci_ops;
- dev_m1533.bus = &bus;
- dev_m1533.sysdata = NULL;
- dev_m1533.devfn = 7*8; // slot 7: M1533 SouthBridge.
- pci_read_config_word(&dev_m1533, 0, &vid);
- if (vid == PCI_VENDOR_ID_AL) {
- printk("Changing mips_machtype to MACH_NEC_ROCKHOPPERII\n");
- mips_machtype = MACH_NEC_ROCKHOPPERII;
- }
- }
-
- /* enable USB input buffers */
- ddb_out32(DDB_PIBMISC, 0x00000007);
-
- /* For dual-function pins, make them all non-GPIO */
- ddb_out32(DDB_GIUFUNSEL, 0x0);
- // ddb_out32(DDB_GIUFUNSEL, 0xfe0fcfff); /* NEC recommanded value */
-
- if (mips_machtype == MACH_NEC_ROCKHOPPERII) {
-
- /* enable IDE controller on Ali chip (south bridge) */
- u8 temp8;
- struct pci_bus bus;
- struct pci_dev dev_m1533;
- struct pci_dev dev_m5229;
- extern struct pci_ops ddb5477_ext_pci_ops;
-
- /* Setup M1535 registers */
- bus.parent = NULL; /* we scan the top level only */
- bus.ops = &ddb5477_ext_pci_ops;
- dev_m1533.bus = &bus;
- dev_m1533.sysdata = NULL;
- dev_m1533.devfn = 7*8; // slot 7: M1533 SouthBridge.
-
- /* setup IDE controller
- * enable IDE controller (bit 6 - 1)
- * IDE IDSEL to be addr:A15 (bit 4:5 - 11)
- * disable IDE ATA Secondary Bus Signal Pad Control (bit 3 - 0)
- * enable IDE ATA Primary Bus Signal Pad Control (bit 2 - 1)
- */
- pci_write_config_byte(&dev_m1533, 0x58, 0x74);
-
- /*
- * positive decode (bit6 -0)
- * enable IDE controler interrupt (bit 4 -1)
- * setup SIRQ to point to IRQ 14 (bit 3:0 - 1101)
- */
- pci_write_config_byte(&dev_m1533, 0x44, 0x1d);
-
- /* Setup M5229 registers */
- dev_m5229.bus = &bus;
- dev_m5229.sysdata = NULL;
- dev_m5229.devfn = 4*8; // slot 4 (AD15): M5229 IDE
-
- /*
- * enable IDE in the M5229 config register 0x50 (bit 0 - 1)
- * M5229 IDSEL is addr:15; see above setting
- */
- pci_read_config_byte(&dev_m5229, 0x50, &temp8);
- pci_write_config_byte(&dev_m5229, 0x50, temp8 | 0x1);
-
- /*
- * enable bus master (bit 2) and IO decoding (bit 0)
- */
- pci_read_config_byte(&dev_m5229, 0x04, &temp8);
- pci_write_config_byte(&dev_m5229, 0x04, temp8 | 0x5);
-
- /*
- * enable native, copied from arch/ppc/k2boot/head.S
- * TODO - need volatile, need to be portable
- */
- pci_write_config_byte(&dev_m5229, 0x09, 0xef);
-
- /* Set Primary Channel Command Block Timing */
- pci_write_config_byte(&dev_m5229, 0x59, 0x31);
-
- /*
- * Enable primary channel 40-pin cable
- * M5229 register 0x4a (bit 0)
- */
- pci_read_config_byte(&dev_m5229, 0x4a, &temp8);
- pci_write_config_byte(&dev_m5229, 0x4a, temp8 | 0x1);
- }
-
- if (mips_machtype == MACH_NEC_ROCKHOPPER
- || mips_machtype == MACH_NEC_ROCKHOPPERII) {
- printk("lcd44780: initializing\n");
- lcd44780_init();
- lcd44780_puts("MontaVista Linux");
- }
-}
# CONFIG_MIPS_XXS1500 is not set
# CONFIG_PNX8550_JBS is not set
# CONFIG_PNX8550_STB810 is not set
-# CONFIG_DDB5477 is not set
# CONFIG_MACH_VR41XX is not set
# CONFIG_PMC_YOSEMITE is not set
# CONFIG_QEMU is not set
# These are still pretty much in the old state, watch, go blind.
#
obj-$(CONFIG_BASLER_EXCITE) += ops-titan.o pci-excite.o fixup-excite.o
-obj-$(CONFIG_DDB5477) += fixup-ddb5477.o pci-ddb5477.o ops-ddb5477.o
obj-$(CONFIG_MIPS_ATLAS) += fixup-atlas.o
obj-$(CONFIG_MIPS_COBALT) += fixup-cobalt.o
obj-$(CONFIG_SOC_AU1500) += fixup-au1000.o ops-au1000.o
+++ /dev/null
-/*
- *
- * BRIEF MODULE DESCRIPTION
- * Board specific pci fixups.
- *
- * Copyright 2001, 2002, 2003 MontaVista Software Inc.
- * Author: Jun Sun, jsun@mvista.com or jsun@junsun.net
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/types.h>
-#include <linux/pci.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-
-static void ddb5477_fixup(struct pci_dev *dev)
-{
- u8 old;
-
- printk(KERN_NOTICE "Enabling ALI M1533/35 PS2 keyboard/mouse.\n");
- pci_read_config_byte(dev, 0x41, &old);
- pci_write_config_byte(dev, 0x41, old | 0xd0);
-}
-
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1533,
- ddb5477_fixup);
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1535,
- ddb5477_fixup);
-
-/*
- * Fixup baseboard AMD chip so that tx does not underflow.
- * bcr_18 |= 0x0800
- * This sets NOUFLO bit which makes tx not start until whole pkt
- * is fetched to the chip.
- */
-#define PCNET32_WIO_RDP 0x10
-#define PCNET32_WIO_RAP 0x12
-#define PCNET32_WIO_RESET 0x14
-#define PCNET32_WIO_BDP 0x16
-
-static void ddb5477_amd_lance_fixup(struct pci_dev *dev)
-{
- unsigned long ioaddr;
- u16 temp;
-
- ioaddr = pci_resource_start(dev, 0);
-
- inw(ioaddr + PCNET32_WIO_RESET); /* reset chip */
-
- /* bcr_18 |= 0x0800 */
- outw(18, ioaddr + PCNET32_WIO_RAP);
- temp = inw(ioaddr + PCNET32_WIO_BDP);
- temp |= 0x0800;
- outw(18, ioaddr + PCNET32_WIO_RAP);
- outw(temp, ioaddr + PCNET32_WIO_BDP);
-}
-
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_LANCE,
- ddb5477_amd_lance_fixup);
+++ /dev/null
-/***********************************************************************
- * Copyright 2001 MontaVista Software Inc.
- * Author: Jun Sun, jsun@mvista.com or jsun@junsun.net
- *
- * arch/mips/ddb5xxx/ddb5477/pci_ops.c
- * Define the pci_ops for DB5477.
- *
- * Much of the code is derived from the original DDB5074 port by
- * Geert Uytterhoeven <geert@sonycom.com>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- ***********************************************************************
- */
-
-/*
- * DDB5477 has two PCI channels, external PCI and IOPIC (internal)
- * Therefore we provide two sets of pci_ops.
- */
-#include <linux/pci.h>
-#include <linux/kernel.h>
-#include <linux/types.h>
-
-#include <asm/addrspace.h>
-#include <asm/debug.h>
-
-#include <asm/ddb5xxx/ddb5xxx.h>
-
-/*
- * config_swap structure records what set of pdar/pmr are used
- * to access pci config space. It also provides a place hold the
- * original values for future restoring.
- */
-struct pci_config_swap {
- u32 pdar;
- u32 pmr;
- u32 config_base;
- u32 config_size;
- u32 pdar_backup;
- u32 pmr_backup;
-};
-
-/*
- * On DDB5477, we have two sets of swap registers, for ext PCI and IOPCI.
- */
-struct pci_config_swap ext_pci_swap = {
- DDB_PCIW0,
- DDB_PCIINIT00,
- DDB_PCI0_CONFIG_BASE,
- DDB_PCI0_CONFIG_SIZE
-};
-struct pci_config_swap io_pci_swap = {
- DDB_IOPCIW0,
- DDB_PCIINIT01,
- DDB_PCI1_CONFIG_BASE,
- DDB_PCI1_CONFIG_SIZE
-};
-
-
-/*
- * access config space
- */
-static inline u32 ddb_access_config_base(struct pci_config_swap *swap, u32 bus, /* 0 means top level bus */
- u32 slot_num)
-{
- u32 pci_addr = 0;
- u32 pciinit_offset = 0;
- u32 virt_addr;
- u32 option;
-
- /* minimum pdar (window) size is 2MB */
- db_assert(swap->config_size >= (2 << 20));
-
- db_assert(slot_num < (1 << 5));
- db_assert(bus < (1 << 8));
-
- /* backup registers */
- swap->pdar_backup = ddb_in32(swap->pdar);
- swap->pmr_backup = ddb_in32(swap->pmr);
-
- /* set the pdar (pci window) register */
- ddb_set_pdar(swap->pdar, swap->config_base, swap->config_size, 32, /* 32 bit wide */
- 0, /* not on local memory bus */
- 0); /* not visible from PCI bus (N/A) */
-
- /*
- * calcuate the absolute pci config addr;
- * according to the spec, we start scanning from adr:11 (0x800)
- */
- if (bus == 0) {
- /* type 0 config */
- pci_addr = 0x800 << slot_num;
- } else {
- /* type 1 config */
- pci_addr = (bus << 16) | (slot_num << 11);
- }
-
- /*
- * if pci_addr is less than pci config window size, we set
- * pciinit_offset to 0 and adjust the virt_address.
- * Otherwise we will try to adjust pciinit_offset.
- */
- if (pci_addr < swap->config_size) {
- virt_addr = KSEG1ADDR(swap->config_base + pci_addr);
- pciinit_offset = 0;
- } else {
- db_assert((pci_addr & (swap->config_size - 1)) == 0);
- virt_addr = KSEG1ADDR(swap->config_base);
- pciinit_offset = pci_addr;
- }
-
- /* set the pmr register */
- option = DDB_PCI_ACCESS_32;
- if (bus != 0)
- option |= DDB_PCI_CFGTYPE1;
- ddb_set_pmr(swap->pmr, DDB_PCICMD_CFG, pciinit_offset, option);
-
- return virt_addr;
-}
-
-static inline void ddb_close_config_base(struct pci_config_swap *swap)
-{
- ddb_out32(swap->pdar, swap->pdar_backup);
- ddb_out32(swap->pmr, swap->pmr_backup);
-}
-
-static int read_config_dword(struct pci_config_swap *swap,
- struct pci_bus *bus, u32 devfn, u32 where,
- u32 * val)
-{
- u32 bus_num, slot_num, func_num;
- u32 base;
-
- db_assert((where & 3) == 0);
- db_assert(where < (1 << 8));
-
- /* check if the bus is top-level */
- if (bus->parent != NULL) {
- bus_num = bus->number;
- db_assert(bus_num != 0);
- } else {
- bus_num = 0;
- }
-
- slot_num = PCI_SLOT(devfn);
- func_num = PCI_FUNC(devfn);
- base = ddb_access_config_base(swap, bus_num, slot_num);
- *val = *(volatile u32 *) (base + (func_num << 8) + where);
- ddb_close_config_base(swap);
- return PCIBIOS_SUCCESSFUL;
-}
-
-static int read_config_word(struct pci_config_swap *swap,
- struct pci_bus *bus, u32 devfn, u32 where,
- u16 * val)
-{
- int status;
- u32 result;
-
- db_assert((where & 1) == 0);
-
- status = read_config_dword(swap, bus, devfn, where & ~3, &result);
- if (where & 2)
- result >>= 16;
- *val = result & 0xffff;
- return status;
-}
-
-static int read_config_byte(struct pci_config_swap *swap,
- struct pci_bus *bus, u32 devfn, u32 where,
- u8 * val)
-{
- int status;
- u32 result;
-
- status = read_config_dword(swap, bus, devfn, where & ~3, &result);
- if (where & 1)
- result >>= 8;
- if (where & 2)
- result >>= 16;
- *val = result & 0xff;
-
- return status;
-}
-
-static int write_config_dword(struct pci_config_swap *swap,
- struct pci_bus *bus, u32 devfn, u32 where,
- u32 val)
-{
- u32 bus_num, slot_num, func_num;
- u32 base;
-
- db_assert((where & 3) == 0);
- db_assert(where < (1 << 8));
-
- /* check if the bus is top-level */
- if (bus->parent != NULL) {
- bus_num = bus->number;
- db_assert(bus_num != 0);
- } else {
- bus_num = 0;
- }
-
- slot_num = PCI_SLOT(devfn);
- func_num = PCI_FUNC(devfn);
- base = ddb_access_config_base(swap, bus_num, slot_num);
- *(volatile u32 *) (base + (func_num << 8) + where) = val;
- ddb_close_config_base(swap);
- return PCIBIOS_SUCCESSFUL;
-}
-
-static int write_config_word(struct pci_config_swap *swap,
- struct pci_bus *bus, u32 devfn, u32 where, u16 val)
-{
- int status, shift = 0;
- u32 result;
-
- db_assert((where & 1) == 0);
-
- status = read_config_dword(swap, bus, devfn, where & ~3, &result);
- if (status != PCIBIOS_SUCCESSFUL)
- return status;
-
- if (where & 2)
- shift += 16;
- result &= ~(0xffff << shift);
- result |= val << shift;
- return write_config_dword(swap, bus, devfn, where & ~3, result);
-}
-
-static int write_config_byte(struct pci_config_swap *swap,
- struct pci_bus *bus, u32 devfn, u32 where, u8 val)
-{
- int status, shift = 0;
- u32 result;
-
- status = read_config_dword(swap, bus, devfn, where & ~3, &result);
- if (status != PCIBIOS_SUCCESSFUL)
- return status;
-
- if (where & 2)
- shift += 16;
- if (where & 1)
- shift += 8;
- result &= ~(0xff << shift);
- result |= val << shift;
- return write_config_dword(swap, bus, devfn, where & ~3, result);
-}
-
-#define MAKE_PCI_OPS(prefix, rw, pciswap, star) \
-static int prefix##_##rw##_config(struct pci_bus *bus, unsigned int devfn, int where, int size, u32 star val) \
-{ \
- if (size == 1) \
- return rw##_config_byte(pciswap, bus, devfn, where, (u8 star)val); \
- else if (size == 2) \
- return rw##_config_word(pciswap, bus, devfn, where, (u16 star)val); \
- /* Size must be 4 */ \
- return rw##_config_dword(pciswap, bus, devfn, where, val); \
-}
-
-MAKE_PCI_OPS(extpci, read, &ext_pci_swap, *)
-MAKE_PCI_OPS(extpci, write, &ext_pci_swap,)
-
-MAKE_PCI_OPS(iopci, read, &io_pci_swap, *)
-MAKE_PCI_OPS(iopci, write, &io_pci_swap,)
-
-struct pci_ops ddb5477_ext_pci_ops = {
- .read = extpci_read_config,
- .write = extpci_write_config
-};
-
-
-struct pci_ops ddb5477_io_pci_ops = {
- .read = iopci_read_config,
- .write = iopci_write_config
-};
+++ /dev/null
-/*
- * PCI code for DDB5477.
- *
- * Copyright (C) 2001 MontaVista Software Inc.
- * Author: Jun Sun, jsun@mvista.com or jsun@junsun.net
- *
- * Copyright (C) 2004 by Ralf Baechle (ralf@linux-mips.org)
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- */
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/types.h>
-#include <linux/pci.h>
-
-#include <asm/bootinfo.h>
-#include <asm/debug.h>
-
-#include <asm/ddb5xxx/ddb5xxx.h>
-
-static struct resource extpci_io_resource = {
- .start = DDB_PCI0_IO_BASE - DDB_PCI_IO_BASE + 0x4000,
- .end = DDB_PCI0_IO_BASE - DDB_PCI_IO_BASE + DDB_PCI0_IO_SIZE - 1,
- .name = "ext pci IO space",
- .flags = IORESOURCE_IO
-};
-
-static struct resource extpci_mem_resource = {
- .start = DDB_PCI0_MEM_BASE + 0x100000,
- .end = DDB_PCI0_MEM_BASE + DDB_PCI0_MEM_SIZE - 1,
- .name = "ext pci memory space",
- .flags = IORESOURCE_MEM
-};
-
-static struct resource iopci_io_resource = {
- .start = DDB_PCI1_IO_BASE - DDB_PCI_IO_BASE,
- .end = DDB_PCI1_IO_BASE - DDB_PCI_IO_BASE + DDB_PCI1_IO_SIZE - 1,
- .name = "io pci IO space",
- .flags = IORESOURCE_IO
-};
-
-static struct resource iopci_mem_resource = {
- .start = DDB_PCI1_MEM_BASE,
- .end = DDB_PCI1_MEM_BASE + DDB_PCI1_MEM_SIZE - 1,
- .name = "ext pci memory space",
- .flags = IORESOURCE_MEM
-};
-
-extern struct pci_ops ddb5477_ext_pci_ops;
-extern struct pci_ops ddb5477_io_pci_ops;
-
-struct pci_controller ddb5477_ext_controller = {
- .pci_ops = &ddb5477_ext_pci_ops,
- .io_resource = &extpci_io_resource,
- .mem_resource = &extpci_mem_resource
-};
-
-struct pci_controller ddb5477_io_controller = {
- .pci_ops = &ddb5477_io_pci_ops,
- .io_resource = &iopci_io_resource,
- .mem_resource = &iopci_mem_resource
-};
-
-
-
-/*
- * we fix up irqs based on the slot number.
- * The first entry is at AD:11.
- * Fortunately this works because, although we have two pci buses,
- * they all have different slot numbers (except for rockhopper slot 20
- * which is handled below).
- *
- */
-
-/*
- * irq mapping : device -> pci int # -> vrc4377 irq# ,
- * ddb5477 board manual page 4 and vrc5477 manual page 46
- */
-
-/*
- * based on ddb5477 manual page 11
- */
-#define MAX_SLOT_NUM 21
-static unsigned char irq_map[MAX_SLOT_NUM] = {
- /* SLOT: 0, AD:11 */ 0xff,
- /* SLOT: 1, AD:12 */ 0xff,
- /* SLOT: 2, AD:13 */ 0xff,
- /* SLOT: 3, AD:14 */ 0xff,
- /* SLOT: 4, AD:15 */ VRC5477_IRQ_INTA, /* onboard tulip */
- /* SLOT: 5, AD:16 */ VRC5477_IRQ_INTB, /* slot 1 */
- /* SLOT: 6, AD:17 */ VRC5477_IRQ_INTC, /* slot 2 */
- /* SLOT: 7, AD:18 */ VRC5477_IRQ_INTD, /* slot 3 */
- /* SLOT: 8, AD:19 */ VRC5477_IRQ_INTE, /* slot 4 */
- /* SLOT: 9, AD:20 */ 0xff,
- /* SLOT: 10, AD:21 */ 0xff,
- /* SLOT: 11, AD:22 */ 0xff,
- /* SLOT: 12, AD:23 */ 0xff,
- /* SLOT: 13, AD:24 */ 0xff,
- /* SLOT: 14, AD:25 */ 0xff,
- /* SLOT: 15, AD:26 */ 0xff,
- /* SLOT: 16, AD:27 */ 0xff,
- /* SLOT: 17, AD:28 */ 0xff,
- /* SLOT: 18, AD:29 */ VRC5477_IRQ_IOPCI_INTC, /* vrc5477 ac97 */
- /* SLOT: 19, AD:30 */ VRC5477_IRQ_IOPCI_INTB, /* vrc5477 usb peri */
- /* SLOT: 20, AD:31 */ VRC5477_IRQ_IOPCI_INTA, /* vrc5477 usb host */
-};
-static unsigned char rockhopperII_irq_map[MAX_SLOT_NUM] = {
- /* SLOT: 0, AD:11 */ 0xff,
- /* SLOT: 1, AD:12 */ VRC5477_IRQ_INTB, /* onboard AMD PCNET */
- /* SLOT: 2, AD:13 */ 0xff,
- /* SLOT: 3, AD:14 */ 0xff,
- /* SLOT: 4, AD:15 */ 14, /* M5229 ide ISA irq */
- /* SLOT: 5, AD:16 */ VRC5477_IRQ_INTD, /* slot 3 */
- /* SLOT: 6, AD:17 */ VRC5477_IRQ_INTA, /* slot 4 */
- /* SLOT: 7, AD:18 */ VRC5477_IRQ_INTD, /* slot 5 */
- /* SLOT: 8, AD:19 */ 0, /* M5457 modem nop */
- /* SLOT: 9, AD:20 */ VRC5477_IRQ_INTA, /* slot 2 */
- /* SLOT: 10, AD:21 */ 0xff,
- /* SLOT: 11, AD:22 */ 0xff,
- /* SLOT: 12, AD:23 */ 0xff,
- /* SLOT: 13, AD:24 */ 0xff,
- /* SLOT: 14, AD:25 */ 0xff,
- /* SLOT: 15, AD:26 */ 0xff,
- /* SLOT: 16, AD:27 */ 0xff,
- /* SLOT: 17, AD:28 */ 0, /* M7101 PMU nop */
- /* SLOT: 18, AD:29 */ VRC5477_IRQ_IOPCI_INTC, /* vrc5477 ac97 */
- /* SLOT: 19, AD:30 */ VRC5477_IRQ_IOPCI_INTB, /* vrc5477 usb peri */
- /* SLOT: 20, AD:31 */ VRC5477_IRQ_IOPCI_INTA, /* vrc5477 usb host */
-};
-
-int __init pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
-{
- int slot_num;
- unsigned char *slot_irq_map;
- unsigned char irq;
-
- /*
- * We ignore the swizzled slot and pin values. The original
- * pci_fixup_irq() codes largely base irq number on the dev slot
- * numbers because except for one case they are unique even
- * though there are multiple pci buses.
- */
-
- if (mips_machtype == MACH_NEC_ROCKHOPPERII)
- slot_irq_map = rockhopperII_irq_map;
- else
- slot_irq_map = irq_map;
-
- slot_num = PCI_SLOT(dev->devfn);
- irq = slot_irq_map[slot_num];
-
- db_assert(slot_num < MAX_SLOT_NUM);
-
- db_assert(irq != 0xff);
-
- pci_write_config_byte(dev, PCI_INTERRUPT_LINE, irq);
-
- if (mips_machtype == MACH_NEC_ROCKHOPPERII) {
- /* hack to distinquish overlapping slot 20s, one
- * on bus 0 (ALI USB on the M1535 on the backplane),
- * and one on bus 2 (NEC USB controller on the CPU board)
- * Make the M1535 USB - ISA IRQ number 9.
- */
- if (slot_num == 20 && dev->bus->number == 0) {
- pci_write_config_byte(dev,
- PCI_INTERRUPT_LINE,
- 9);
- irq = 9;
- }
-
- }
-
- return irq;
-}
-
-/* Do platform specific device initialization at pci_enable_device() time */
-int pcibios_plat_dev_init(struct pci_dev *dev)
-{
- return 0;
-}
-
-void ddb_pci_reset_bus(void)
-{
- u32 temp;
-
- /*
- * I am not sure about the "official" procedure, the following
- * steps work as far as I know:
- * We first set PCI cold reset bit (bit 31) in PCICTRL-H.
- * Then we clear the PCI warm reset bit (bit 30) to 0 in PCICTRL-H.
- * The same is true for both PCI channels.
- */
- temp = ddb_in32(DDB_PCICTL0_H);
- temp |= 0x80000000;
- ddb_out32(DDB_PCICTL0_H, temp);
- temp &= ~0xc0000000;
- ddb_out32(DDB_PCICTL0_H, temp);
-
- temp = ddb_in32(DDB_PCICTL1_H);
- temp |= 0x80000000;
- ddb_out32(DDB_PCICTL1_H, temp);
- temp &= ~0xc0000000;
- ddb_out32(DDB_PCICTL1_H, temp);
-}
#define MACH_GROUP_COBALT 7 /* Cobalt servers */
#define MACH_COBALT_27 0 /* Proto "27" hardware */
-/*
- * Valid machtype for group NEC DDB
- */
-#define MACH_GROUP_NEC_DDB 8 /* NEC DDB */
-#define MACH_NEC_DDB5074 0 /* NEC DDB Vrc-5074 */
-#define MACH_NEC_DDB5476 1 /* NEC DDB Vrc-5476 */
-#define MACH_NEC_DDB5477 2 /* NEC DDB Vrc-5477 */
-#define MACH_NEC_ROCKHOPPER 3 /* Rockhopper base board */
-#define MACH_NEC_ROCKHOPPERII 4 /* Rockhopper II base board */
-
/*
* Valid machtype for group BAGET
*/
+++ /dev/null
-/***********************************************************************
- *
- * Copyright 2001 MontaVista Software Inc.
- * Author: jsun@mvista.com or jsun@junsun.net
- *
- * include/asm-mips/ddb5xxx/ddb5477.h
- * DDB 5477 specific definitions and macros.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- ***********************************************************************
- */
-
-#ifndef __ASM_DDB5XXX_DDB5477_H
-#define __ASM_DDB5XXX_DDB5477_H
-
-#include <irq.h>
-
-/*
- * This contains macros that are specific to DDB5477 or renamed from
- * DDB5476.
- */
-
-/*
- * renamed PADRs
- */
-#define DDB_LCS0 DDB_DCS2
-#define DDB_LCS1 DDB_DCS3
-#define DDB_LCS2 DDB_DCS4
-#define DDB_VRC5477 DDB_INTCS
-
-/*
- * New CPU interface registers
- */
-#define DDB_INTCTRL0 0x0400 /* Interrupt Control 0 */
-#define DDB_INTCTRL1 0x0404 /* Interrupt Control 1 */
-#define DDB_INTCTRL2 0x0408 /* Interrupt Control 2 */
-#define DDB_INTCTRL3 0x040c /* Interrupt Control 3 */
-
-#define DDB_INT0STAT 0x0420 /* INT0 Status [R] */
-#define DDB_INT1STAT 0x0428 /* INT1 Status [R] */
-#define DDB_INT2STAT 0x0430 /* INT2 Status [R] */
-#define DDB_INT3STAT 0x0438 /* INT3 Status [R] */
-#define DDB_INT4STAT 0x0440 /* INT4 Status [R] */
-#define DDB_NMISTAT 0x0450 /* NMI Status [R] */
-
-#define DDB_INTCLR32 0x0468 /* Interrupt Clear */
-
-#define DDB_INTPPES0 0x0470 /* PCI0 Interrupt Control */
-#define DDB_INTPPES1 0x0478 /* PCI1 Interrupt Control */
-
-#undef DDB_CPUSTAT /* duplicate in Vrc-5477 */
-#define DDB_CPUSTAT 0x0480 /* CPU Status [R] */
-#define DDB_BUSCTRL 0x0488 /* Internal Bus Control */
-
-
-/*
- * Timer registers
- */
-#define DDB_REFCTRL_L DDB_T0CTRL
-#define DDB_REFCTRL_H (DDB_T0CTRL+4)
-#define DDB_REFCNTR DDB_T0CNTR
-#define DDB_SPT0CTRL_L DDB_T1CTRL
-#define DDB_SPT0CTRL_H (DDB_T1CTRL+4)
-#define DDB_SPT1CTRL_L DDB_T2CTRL
-#define DDB_SPT1CTRL_H (DDB_T2CTRL+4)
-#define DDB_SPT1CNTR DDB_T1CTRL
-#define DDB_WDTCTRL_L DDB_T3CTRL
-#define DDB_WDTCTRL_H (DDB_T3CTRL+4)
-#define DDB_WDTCNTR DDB_T3CNTR
-
-/*
- * DMA registers are moved. We don't care about it for now. TODO.
- */
-
-/*
- * BARs for ext PCI (PCI0)
- */
-#undef DDB_BARC
-#undef DDB_BARB
-
-#define DDB_BARC0 0x0210 /* PCI0 Control */
-#define DDB_BARM010 0x0218 /* PCI0 SDRAM bank01 */
-#define DDB_BARM230 0x0220 /* PCI0 SDRAM bank23 */
-#define DDB_BAR00 0x0240 /* PCI0 LDCS0 */
-#define DDB_BAR10 0x0248 /* PCI0 LDCS1 */
-#define DDB_BAR20 0x0250 /* PCI0 LDCS2 */
-#define DDB_BAR30 0x0258 /* PCI0 LDCS3 */
-#define DDB_BAR40 0x0260 /* PCI0 LDCS4 */
-#define DDB_BAR50 0x0268 /* PCI0 LDCS5 */
-#define DDB_BARB0 0x0280 /* PCI0 BOOT */
-#define DDB_BARP00 0x0290 /* PCI0 for IOPCI Window0 */
-#define DDB_BARP10 0x0298 /* PCI0 for IOPCI Window1 */
-
-/*
- * BARs for IOPIC (PCI1)
- */
-#define DDB_BARC1 0x0610 /* PCI1 Control */
-#define DDB_BARM011 0x0618 /* PCI1 SDRAM bank01 */
-#define DDB_BARM231 0x0620 /* PCI1 SDRAM bank23 */
-#define DDB_BAR01 0x0640 /* PCI1 LDCS0 */
-#define DDB_BAR11 0x0648 /* PCI1 LDCS1 */
-#define DDB_BAR21 0x0650 /* PCI1 LDCS2 */
-#define DDB_BAR31 0x0658 /* PCI1 LDCS3 */
-#define DDB_BAR41 0x0660 /* PCI1 LDCS4 */
-#define DDB_BAR51 0x0668 /* PCI1 LDCS5 */
-#define DDB_BARB1 0x0680 /* PCI1 BOOT */
-#define DDB_BARP01 0x0690 /* PCI1 for ext PCI Window0 */
-#define DDB_BARP11 0x0698 /* PCI1 for ext PCI Window1 */
-
-/*
- * Other registers for ext PCI (PCI0)
- */
-#define DDB_PCIINIT00 0x02f0 /* PCI0 Initiator 0 */
-#define DDB_PCIINIT10 0x02f8 /* PCI0 Initiator 1 */
-
-#define DDB_PCISWP0 0x02b0 /* PCI0 Swap */
-#define DDB_PCIERR0 0x02b8 /* PCI0 Error */
-
-#define DDB_PCICTL0_L 0x02e0 /* PCI0 Control-L */
-#define DDB_PCICTL0_H 0x02e4 /* PCI0 Control-H */
-#define DDB_PCIARB0_L 0x02e8 /* PCI0 Arbitration-L */
-#define DDB_PCIARB0_H 0x02ec /* PCI0 Arbitration-H */
-
-/*
- * Other registers for IOPCI (PCI1)
- */
-#define DDB_IOPCIW0 0x00d0 /* PCI Address Window 0 [R/W] */
-#define DDB_IOPCIW1 0x00d8 /* PCI Address Window 1 [R/W] */
-
-#define DDB_PCIINIT01 0x06f0 /* PCI1 Initiator 0 */
-#define DDB_PCIINIT11 0x06f8 /* PCI1 Initiator 1 */
-
-#define DDB_PCISWP1 0x06b0 /* PCI1 Swap */
-#define DDB_PCIERR1 0x06b8 /* PCI1 Error */
-
-#define DDB_PCICTL1_L 0x06e0 /* PCI1 Control-L */
-#define DDB_PCICTL1_H 0x06e4 /* PCI1 Control-H */
-#define DDB_PCIARB1_L 0x06e8 /* PCI1 Arbitration-L */
-#define DDB_PCIARB1_H 0x06ec /* PCI1 Arbitration-H */
-
-/*
- * Local Bus
- */
-#define DDB_LCST0 0x0110 /* LB Chip Select Timing 0 */
-#define DDB_LCST1 0x0118 /* LB Chip Select Timing 1 */
-#undef DDB_LCST2
-#define DDB_LCST2 0x0120 /* LB Chip Select Timing 2 */
-#undef DDB_LCST3
-#undef DDB_LCST4
-#undef DDB_LCST5
-#undef DDB_LCST6
-#undef DDB_LCST7
-#undef DDB_LCST8
-#define DDB_ERRADR 0x0150 /* Error Address Register */
-#define DDB_ERRCS 0x0160
-#define DDB_BTM 0x0170 /* Boot Time Mode value */
-
-/*
- * MISC registers
- */
-#define DDB_GIUFUNSEL 0x4040 /* select dual-func pins */
-#define DDB_PIBMISC 0x0750 /* USB buffer enable / power saving */
-
-/*
- * Memory map (physical address)
- *
- * Note most of the following address must be properly aligned by the
- * corresponding size. For example, if PCI_IO_SIZE is 16MB, then
- * PCI_IO_BASE must be aligned along 16MB boundary.
- */
-
-/* the actual ram size is detected at run-time */
-#define DDB_SDRAM_BASE 0x00000000
-#define DDB_MAX_SDRAM_SIZE 0x08000000 /* less than 128MB */
-
-#define DDB_PCI0_MEM_BASE 0x08000000
-#define DDB_PCI0_MEM_SIZE 0x08000000 /* 128 MB */
-
-#define DDB_PCI1_MEM_BASE 0x10000000
-#define DDB_PCI1_MEM_SIZE 0x08000000 /* 128 MB */
-
-#define DDB_PCI0_CONFIG_BASE 0x18000000
-#define DDB_PCI0_CONFIG_SIZE 0x01000000 /* 16 MB */
-
-#define DDB_PCI1_CONFIG_BASE 0x19000000
-#define DDB_PCI1_CONFIG_SIZE 0x01000000 /* 16 MB */
-
-#define DDB_PCI_IO_BASE 0x1a000000 /* we concatenate two IOs */
-#define DDB_PCI0_IO_BASE 0x1a000000
-#define DDB_PCI0_IO_SIZE 0x01000000 /* 16 MB */
-#define DDB_PCI1_IO_BASE 0x1b000000
-#define DDB_PCI1_IO_SIZE 0x01000000 /* 16 MB */
-
-#define DDB_LCS0_BASE 0x1c000000 /* flash memory */
-#define DDB_LCS0_SIZE 0x01000000 /* 16 MB */
-
-#define DDB_LCS1_BASE 0x1d000000 /* misc */
-#define DDB_LCS1_SIZE 0x01000000 /* 16 MB */
-
-#define DDB_LCS2_BASE 0x1e000000 /* Mezzanine */
-#define DDB_LCS2_SIZE 0x01000000 /* 16 MB */
-
-#define DDB_VRC5477_BASE 0x1fa00000 /* VRC5477 control regs */
-#define DDB_VRC5477_SIZE 0x00200000 /* 2MB */
-
-#define DDB_BOOTCS_BASE 0x1fc00000 /* Boot ROM / EPROM /Flash */
-#define DDB_BOOTCS_SIZE 0x00200000 /* 2 MB - doc says 4MB */
-
-#define DDB_LED DDB_LCS1_BASE + 0x10000
-
-
-/*
- * DDB5477 specific functions
- */
-#ifndef __ASSEMBLY__
-extern void ddb5477_irq_setup(void);
-
-/* route irq to cpu int pin */
-extern void ll_vrc5477_irq_route(int vrc5477_irq, int ip);
-
-/* low-level routine for enabling vrc5477 irq, bypassing high-level */
-extern void ll_vrc5477_irq_enable(int vrc5477_irq);
-extern void ll_vrc5477_irq_disable(int vrc5477_irq);
-#endif /* !__ASSEMBLY__ */
-
-/* PCI intr ack share PCIW0 with PCI IO */
-#define DDB_PCI_IACK_BASE DDB_PCI_IO_BASE
-
-/*
- * Interrupt mapping
- *
- * We have three interrupt controllers:
- *
- * . CPU itself - 8 sources
- * . i8259 - 16 sources
- * . vrc5477 - 32 sources
- *
- * They connected as follows:
- * all vrc5477 interrupts are routed to cpu IP2 (by software setting)
- * all i8359 are routed to INTC in vrc5477 (by hardware connection)
- *
- * All VRC5477 PCI interrupts are level-triggered (no ack needed).
- * All PCI irq but INTC are active low.
- */
-
-/*
- * irq number block assignment
- */
-
-#define NUM_CPU_IRQ 8
-#define NUM_VRC5477_IRQ 32
-
-#define CPU_IRQ_BASE MIPS_CPU_IRQ_BASE
-#define VRC5477_IRQ_BASE (CPU_IRQ_BASE + NUM_CPU_IRQ)
-
-/*
- * vrc5477 irq defs
- */
-
-#define VRC5477_IRQ_CPCE (0 + VRC5477_IRQ_BASE) /* cpu parity error */
-#define VRC5477_IRQ_CNTD (1 + VRC5477_IRQ_BASE) /* cpu no target */
-#define VRC5477_IRQ_I2C (2 + VRC5477_IRQ_BASE) /* I2C */
-#define VRC5477_IRQ_DMA (3 + VRC5477_IRQ_BASE) /* DMA */
-#define VRC5477_IRQ_UART0 (4 + VRC5477_IRQ_BASE)
-#define VRC5477_IRQ_WDOG (5 + VRC5477_IRQ_BASE) /* watchdog timer */
-#define VRC5477_IRQ_SPT1 (6 + VRC5477_IRQ_BASE) /* special purpose timer 1 */
-#define VRC5477_IRQ_LBRT (7 + VRC5477_IRQ_BASE) /* local bus read timeout */
-#define VRC5477_IRQ_INTA (8 + VRC5477_IRQ_BASE) /* PCI INT #A */
-#define VRC5477_IRQ_INTB (9 + VRC5477_IRQ_BASE) /* PCI INT #B */
-#define VRC5477_IRQ_INTC (10 + VRC5477_IRQ_BASE) /* PCI INT #C */
-#define VRC5477_IRQ_INTD (11 + VRC5477_IRQ_BASE) /* PCI INT #D */
-#define VRC5477_IRQ_INTE (12 + VRC5477_IRQ_BASE) /* PCI INT #E */
-#define VRC5477_IRQ_RESERVED_13 (13 + VRC5477_IRQ_BASE) /* reserved */
-#define VRC5477_IRQ_PCIS (14 + VRC5477_IRQ_BASE) /* PCI SERR # */
-#define VRC5477_IRQ_PCI (15 + VRC5477_IRQ_BASE) /* PCI internal error */
-#define VRC5477_IRQ_IOPCI_INTA (16 + VRC5477_IRQ_BASE) /* USB-H */
-#define VRC5477_IRQ_IOPCI_INTB (17 + VRC5477_IRQ_BASE) /* USB-P */
-#define VRC5477_IRQ_IOPCI_INTC (18 + VRC5477_IRQ_BASE) /* AC97 */
-#define VRC5477_IRQ_IOPCI_INTD (19 + VRC5477_IRQ_BASE) /* Reserved */
-#define VRC5477_IRQ_UART1 (20 + VRC5477_IRQ_BASE)
-#define VRC5477_IRQ_SPT0 (21 + VRC5477_IRQ_BASE) /* special purpose timer 0 */
-#define VRC5477_IRQ_GPT0 (22 + VRC5477_IRQ_BASE) /* general purpose timer 0 */
-#define VRC5477_IRQ_GPT1 (23 + VRC5477_IRQ_BASE) /* general purpose timer 1 */
-#define VRC5477_IRQ_GPT2 (24 + VRC5477_IRQ_BASE) /* general purpose timer 2 */
-#define VRC5477_IRQ_GPT3 (25 + VRC5477_IRQ_BASE) /* general purpose timer 3 */
-#define VRC5477_IRQ_GPIO (26 + VRC5477_IRQ_BASE)
-#define VRC5477_IRQ_SIO0 (27 + VRC5477_IRQ_BASE)
-#define VRC5477_IRQ_SIO1 (28 + VRC5477_IRQ_BASE)
-#define VRC5477_IRQ_RESERVED_29 (29 + VRC5477_IRQ_BASE) /* reserved */
-#define VRC5477_IRQ_IOPCISERR (30 + VRC5477_IRQ_BASE) /* IO PCI SERR # */
-#define VRC5477_IRQ_IOPCI (31 + VRC5477_IRQ_BASE)
-
-/*
- * i2859 irq assignment
- */
-#define I8259_IRQ_RESERVED_0 (0 + I8259A_IRQ_BASE)
-#define I8259_IRQ_KEYBOARD (1 + I8259A_IRQ_BASE) /* M1543 default */
-#define I8259_IRQ_CASCADE (2 + I8259A_IRQ_BASE)
-#define I8259_IRQ_UART_B (3 + I8259A_IRQ_BASE) /* M1543 default, may conflict with RTC according to schematic diagram */
-#define I8259_IRQ_UART_A (4 + I8259A_IRQ_BASE) /* M1543 default */
-#define I8259_IRQ_PARALLEL (5 + I8259A_IRQ_BASE) /* M1543 default */
-#define I8259_IRQ_RESERVED_6 (6 + I8259A_IRQ_BASE)
-#define I8259_IRQ_RESERVED_7 (7 + I8259A_IRQ_BASE)
-#define I8259_IRQ_RTC (8 + I8259A_IRQ_BASE) /* who set this? */
-#define I8259_IRQ_USB (9 + I8259A_IRQ_BASE) /* ddb_setup */
-#define I8259_IRQ_PMU (10 + I8259A_IRQ_BASE) /* ddb_setup */
-#define I8259_IRQ_RESERVED_11 (11 + I8259A_IRQ_BASE)
-#define I8259_IRQ_RESERVED_12 (12 + I8259A_IRQ_BASE) /* m1543_irq_setup */
-#define I8259_IRQ_RESERVED_13 (13 + I8259A_IRQ_BASE)
-#define I8259_IRQ_HDC1 (14 + I8259A_IRQ_BASE) /* default and ddb_setup */
-#define I8259_IRQ_HDC2 (15 + I8259A_IRQ_BASE) /* default */
-
-
-/*
- * misc
- */
-#define VRC5477_I8259_CASCADE (VRC5477_IRQ_INTC - VRC5477_IRQ_BASE)
-#define CPU_VRC5477_CASCADE 2
-
-/*
- * debug routines
- */
-#ifndef __ASSEMBLY__
-#if defined(CONFIG_RUNTIME_DEBUG)
-extern void vrc5477_show_pdar_regs(void);
-extern void vrc5477_show_pci_regs(void);
-extern void vrc5477_show_bar_regs(void);
-extern void vrc5477_show_int_regs(void);
-extern void vrc5477_show_all_regs(void);
-#endif
-
-/*
- * RAM size
- */
-extern int board_ram_size;
-#endif /* !__ASSEMBLY__ */
-
-#endif /* __ASM_DDB5XXX_DDB5477_H */
+++ /dev/null
-/*
- * Copyright 2001 MontaVista Software Inc.
- * Author: jsun@mvista.com or jsun@junsun.net
- *
- * Copyright (C) 2000 Geert Uytterhoeven <geert@sonycom.com>
- * Sony Software Development Center Europe (SDCE), Brussels
- *
- * include/asm-mips/ddb5xxx/ddb5xxx.h
- * Common header for all NEC DDB 5xxx boards, including 5074, 5476, 5477.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- */
-
-#ifndef __ASM_DDB5XXX_DDB5XXX_H
-#define __ASM_DDB5XXX_DDB5XXX_H
-
-#include <linux/types.h>
-
-/*
- * This file is based on the following documentation:
- *
- * NEC Vrc 5074 System Controller Data Sheet, June 1998
- *
- * [jsun] It is modified so that this file only contains the macros
- * that are true for all DDB 5xxx boards. The modification is based on
- *
- * uPD31577(VRC5477) VR5432-SDRAM/PCI Bridge (Luke)
- * Preliminary Specification Decoment, Rev 1.1, 27 Dec, 2000
- *
- */
-
-
-#define DDB_BASE 0xbfa00000
-#define DDB_SIZE 0x00200000 /* 2 MB */
-
-
-/*
- * Physical Device Address Registers (PDARs)
- */
-
-#define DDB_SDRAM0 0x0000 /* SDRAM Bank 0 [R/W] */
-#define DDB_SDRAM1 0x0008 /* SDRAM Bank 1 [R/W] */
-#define DDB_DCS2 0x0010 /* Device Chip-Select 2 [R/W] */
-#define DDB_DCS3 0x0018 /* Device Chip-Select 3 [R/W] */
-#define DDB_DCS4 0x0020 /* Device Chip-Select 4 [R/W] */
-#define DDB_DCS5 0x0028 /* Device Chip-Select 5 [R/W] */
-#define DDB_DCS6 0x0030 /* Device Chip-Select 6 [R/W] */
-#define DDB_DCS7 0x0038 /* Device Chip-Select 7 [R/W] */
-#define DDB_DCS8 0x0040 /* Device Chip-Select 8 [R/W] */
-#define DDB_PCIW0 0x0060 /* PCI Address Window 0 [R/W] */
-#define DDB_PCIW1 0x0068 /* PCI Address Window 1 [R/W] */
-#define DDB_INTCS 0x0070 /* Controller Internal Registers and Devices */
- /* [R/W] */
-#define DDB_BOOTCS 0x0078 /* Boot ROM Chip-Select [R/W] */
-/* Vrc5477 has two more, IOPCIW0, IOPCIW1 */
-
-/*
- * CPU Interface Registers
- */
-#define DDB_CPUSTAT 0x0080 /* CPU Status [R/W] */
-#define DDB_INTCTRL 0x0088 /* Interrupt Control [R/W] */
-#define DDB_INTSTAT0 0x0090 /* Interrupt Status 0 [R] */
-#define DDB_INTSTAT1 0x0098 /* Interrupt Status 1 and CPU Interrupt */
- /* Enable [R/W] */
-#define DDB_INTCLR 0x00A0 /* Interrupt Clear [R/W] */
-#define DDB_INTPPES 0x00A8 /* PCI Interrupt Control [R/W] */
-
-
-/*
- * Memory-Interface Registers
- */
-#define DDB_MEMCTRL 0x00C0 /* Memory Control */
-#define DDB_ACSTIME 0x00C8 /* Memory Access Timing [R/W] */
-#define DDB_CHKERR 0x00D0 /* Memory Check Error Status [R] */
-
-
-/*
- * PCI-Bus Registers
- */
-#define DDB_PCICTRL 0x00E0 /* PCI Control [R/W] */
-#define DDB_PCIARB 0x00E8 /* PCI Arbiter [R/W] */
-#define DDB_PCIINIT0 0x00F0 /* PCI Master (Initiator) 0 [R/W] */
-#define DDB_PCIINIT1 0x00F8 /* PCI Master (Initiator) 1 [R/W] */
-#define DDB_PCIERR 0x00B8 /* PCI Error [R/W] */
-
-
-/*
- * Local-Bus Registers
- */
-#define DDB_LCNFG 0x0100 /* Local Bus Configuration [R/W] */
-#define DDB_LCST2 0x0110 /* Local Bus Chip-Select Timing 2 [R/W] */
-#define DDB_LCST3 0x0118 /* Local Bus Chip-Select Timing 3 [R/W] */
-#define DDB_LCST4 0x0120 /* Local Bus Chip-Select Timing 4 [R/W] */
-#define DDB_LCST5 0x0128 /* Local Bus Chip-Select Timing 5 [R/W] */
-#define DDB_LCST6 0x0130 /* Local Bus Chip-Select Timing 6 [R/W] */
-#define DDB_LCST7 0x0138 /* Local Bus Chip-Select Timing 7 [R/W] */
-#define DDB_LCST8 0x0140 /* Local Bus Chip-Select Timing 8 [R/W] */
-#define DDB_DCSFN 0x0150 /* Device Chip-Select Muxing and Output */
- /* Enables [R/W] */
-#define DDB_DCSIO 0x0158 /* Device Chip-Selects As I/O Bits [R/W] */
-#define DDB_BCST 0x0178 /* Local Boot Chip-Select Timing [R/W] */
-
-
-/*
- * DMA Registers
- */
-#define DDB_DMACTRL0 0x0180 /* DMA Control 0 [R/W] */
-#define DDB_DMASRCA0 0x0188 /* DMA Source Address 0 [R/W] */
-#define DDB_DMADESA0 0x0190 /* DMA Destination Address 0 [R/W] */
-#define DDB_DMACTRL1 0x0198 /* DMA Control 1 [R/W] */
-#define DDB_DMASRCA1 0x01A0 /* DMA Source Address 1 [R/W] */
-#define DDB_DMADESA1 0x01A8 /* DMA Destination Address 1 [R/W] */
-
-
-/*
- * Timer Registers
- */
-#define DDB_T0CTRL 0x01C0 /* SDRAM Refresh Control [R/W] */
-#define DDB_T0CNTR 0x01C8 /* SDRAM Refresh Counter [R/W] */
-#define DDB_T1CTRL 0x01D0 /* CPU-Bus Read Time-Out Control [R/W] */
-#define DDB_T1CNTR 0x01D8 /* CPU-Bus Read Time-Out Counter [R/W] */
-#define DDB_T2CTRL 0x01E0 /* General-Purpose Timer Control [R/W] */
-#define DDB_T2CNTR 0x01E8 /* General-Purpose Timer Counter [R/W] */
-#define DDB_T3CTRL 0x01F0 /* Watchdog Timer Control [R/W] */
-#define DDB_T3CNTR 0x01F8 /* Watchdog Timer Counter [R/W] */
-
-
-/*
- * PCI Configuration Space Registers
- */
-#define DDB_PCI_BASE 0x0200
-
-#define DDB_VID 0x0200 /* PCI Vendor ID [R] */
-#define DDB_DID 0x0202 /* PCI Device ID [R] */
-#define DDB_PCICMD 0x0204 /* PCI Command [R/W] */
-#define DDB_PCISTS 0x0206 /* PCI Status [R/W] */
-#define DDB_REVID 0x0208 /* PCI Revision ID [R] */
-#define DDB_CLASS 0x0209 /* PCI Class Code [R] */
-#define DDB_CLSIZ 0x020C /* PCI Cache Line Size [R/W] */
-#define DDB_MLTIM 0x020D /* PCI Latency Timer [R/W] */
-#define DDB_HTYPE 0x020E /* PCI Header Type [R] */
-#define DDB_BIST 0x020F /* BIST [R] (unimplemented) */
-#define DDB_BARC 0x0210 /* PCI Base Address Register Control [R/W] */
-#define DDB_BAR0 0x0218 /* PCI Base Address Register 0 [R/W] */
-#define DDB_BAR1 0x0220 /* PCI Base Address Register 1 [R/W] */
-#define DDB_CIS 0x0228 /* PCI Cardbus CIS Pointer [R] */
- /* (unimplemented) */
-#define DDB_SSVID 0x022C /* PCI Sub-System Vendor ID [R/W] */
-#define DDB_SSID 0x022E /* PCI Sub-System ID [R/W] */
-#define DDB_ROM 0x0230 /* Expansion ROM Base Address [R] */
- /* (unimplemented) */
-#define DDB_INTLIN 0x023C /* PCI Interrupt Line [R/W] */
-#define DDB_INTPIN 0x023D /* PCI Interrupt Pin [R] */
-#define DDB_MINGNT 0x023E /* PCI Min_Gnt [R] (unimplemented) */
-#define DDB_MAXLAT 0x023F /* PCI Max_Lat [R] (unimplemented) */
-#define DDB_BAR2 0x0240 /* PCI Base Address Register 2 [R/W] */
-#define DDB_BAR3 0x0248 /* PCI Base Address Register 3 [R/W] */
-#define DDB_BAR4 0x0250 /* PCI Base Address Register 4 [R/W] */
-#define DDB_BAR5 0x0258 /* PCI Base Address Register 5 [R/W] */
-#define DDB_BAR6 0x0260 /* PCI Base Address Register 6 [R/W] */
-#define DDB_BAR7 0x0268 /* PCI Base Address Register 7 [R/W] */
-#define DDB_BAR8 0x0270 /* PCI Base Address Register 8 [R/W] */
-#define DDB_BARB 0x0278 /* PCI Base Address Register BOOT [R/W] */
-
-
-/*
- * Nile 4 Register Access
- */
-
-static inline void ddb_sync(void)
-{
- volatile u32 *p = (volatile u32 *)0xbfc00000;
- (void)(*p);
-}
-
-static inline void ddb_out32(u32 offset, u32 val)
-{
- *(volatile u32 *)(DDB_BASE+offset) = val;
- ddb_sync();
-}
-
-static inline u32 ddb_in32(u32 offset)
-{
- u32 val = *(volatile u32 *)(DDB_BASE+offset);
- ddb_sync();
- return val;
-}
-
-static inline void ddb_out16(u32 offset, u16 val)
-{
- *(volatile u16 *)(DDB_BASE+offset) = val;
- ddb_sync();
-}
-
-static inline u16 ddb_in16(u32 offset)
-{
- u16 val = *(volatile u16 *)(DDB_BASE+offset);
- ddb_sync();
- return val;
-}
-
-static inline void ddb_out8(u32 offset, u8 val)
-{
- *(volatile u8 *)(DDB_BASE+offset) = val;
- ddb_sync();
-}
-
-static inline u8 ddb_in8(u32 offset)
-{
- u8 val = *(volatile u8 *)(DDB_BASE+offset);
- ddb_sync();
- return val;
-}
-
-
-/*
- * Physical Device Address Registers
- */
-
-extern u32
-ddb_calc_pdar(u32 phys, u32 size, int width, int on_memory_bus, int pci_visible);
-extern void
-ddb_set_pdar(u32 pdar, u32 phys, u32 size, int width,
- int on_memory_bus, int pci_visible);
-
-/*
- * PCI Master Registers
- */
-
-#define DDB_PCICMD_IACK 0 /* PCI Interrupt Acknowledge */
-#define DDB_PCICMD_IO 1 /* PCI I/O Space */
-#define DDB_PCICMD_MEM 3 /* PCI Memory Space */
-#define DDB_PCICMD_CFG 5 /* PCI Configuration Space */
-
-/*
- * additional options for pci init reg (no shifting needed)
- */
-#define DDB_PCI_CFGTYPE1 0x200 /* for pci init0/1 regs */
-#define DDB_PCI_ACCESS_32 0x10 /* for pci init0/1 regs */
-
-
-extern void ddb_set_pmr(u32 pmr, u32 type, u32 addr, u32 options);
-
-/*
- * we need to reset pci bus when we start up and shutdown
- */
-extern void ddb_pci_reset_bus(void);
-
-
-/*
- * include the board dependent part
- */
-#if defined(CONFIG_DDB5477)
-#include <asm/ddb5xxx/ddb5477.h>
-#else
-#error "Unknown DDB board!"
-#endif
-
-#endif /* __ASM_DDB5XXX_DDB5XXX_H */
projects / linux-2.6 / commitdiff