Make some TX3927 SoC specific code independent from board specific code.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
obj-y += setup.o
obj-$(CONFIG_PCI) += pci.o
+obj-$(CONFIG_SOC_TX3927) += setup_tx3927.o irq_tx3927.o
obj-$(CONFIG_SOC_TX4927) += mem_tx4927.o setup_tx4927.o irq_tx4927.o
obj-$(CONFIG_SOC_TX4938) += mem_tx4927.o setup_tx4938.o irq_tx4938.o
obj-$(CONFIG_TOSHIBA_FPCIB0) += smsc_fdc37m81x.o
--- /dev/null
+/*
+ * Common tx3927 irq handler
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright 2001 MontaVista Software Inc.
+ * Copyright (C) 2000-2001 Toshiba Corporation
+ */
+#include <linux/init.h>
+#include <asm/txx9irq.h>
+#include <asm/txx9/tx3927.h>
+
+void __init tx3927_irq_init(void)
+{
+ int i;
+
+ txx9_irq_init(TX3927_IRC_REG);
+ /* raise priority for timers, sio */
+ for (i = 0; i < TX3927_NR_TMR; i++)
+ txx9_irq_set_pri(TX3927_IR_TMR(i), 6);
+ for (i = 0; i < TX3927_NR_SIO; i++)
+ txx9_irq_set_pri(TX3927_IR_SIO(i), 7);
+}
--- /dev/null
+/*
+ * TX3927 setup routines
+ * Based on linux/arch/mips/txx9/jmr3927/setup.c
+ *
+ * Copyright 2001 MontaVista Software Inc.
+ * Copyright (C) 2000-2001 Toshiba Corporation
+ * Copyright (C) 2007 Ralf Baechle (ralf@linux-mips.org)
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+#include <linux/init.h>
+#include <linux/ioport.h>
+#include <linux/delay.h>
+#include <linux/serial_core.h>
+#include <linux/param.h>
+#include <asm/mipsregs.h>
+#include <asm/txx9irq.h>
+#include <asm/txx9tmr.h>
+#include <asm/txx9pio.h>
+#include <asm/txx9/generic.h>
+#include <asm/txx9/tx3927.h>
+
+void __init tx3927_wdt_init(void)
+{
+ txx9_wdt_init(TX3927_TMR_REG(2));
+}
+
+void __init tx3927_setup(void)
+{
+ int i;
+ unsigned int conf;
+
+ /* don't enable - see errata */
+ txx9_ccfg_toeon = 0;
+ if (strstr(prom_getcmdline(), "toeon") != NULL)
+ txx9_ccfg_toeon = 1;
+
+ txx9_reg_res_init(TX3927_REV_PCODE(), TX3927_REG_BASE,
+ TX3927_REG_SIZE);
+
+ /* SDRAMC,ROMC are configured by PROM */
+ for (i = 0; i < 8; i++) {
+ if (!(tx3927_romcptr->cr[i] & 0x8))
+ continue; /* disabled */
+ txx9_ce_res[i].start = (unsigned long)TX3927_ROMC_BA(i);
+ txx9_ce_res[i].end =
+ txx9_ce_res[i].start + TX3927_ROMC_SIZE(i) - 1;
+ request_resource(&iomem_resource, &txx9_ce_res[i]);
+ }
+
+ /* clocks */
+ txx9_gbus_clock = txx9_cpu_clock / 2;
+ /* change default value to udelay/mdelay take reasonable time */
+ loops_per_jiffy = txx9_cpu_clock / HZ / 2;
+
+ /* CCFG */
+ /* enable Timeout BusError */
+ if (txx9_ccfg_toeon)
+ tx3927_ccfgptr->ccfg |= TX3927_CCFG_TOE;
+
+ /* clear BusErrorOnWrite flag */
+ tx3927_ccfgptr->ccfg &= ~TX3927_CCFG_BEOW;
+ if (read_c0_conf() & TX39_CONF_WBON)
+ /* Disable PCI snoop */
+ tx3927_ccfgptr->ccfg &= ~TX3927_CCFG_PSNP;
+ else
+ /* Enable PCI SNOOP - with write through only */
+ tx3927_ccfgptr->ccfg |= TX3927_CCFG_PSNP;
+ /* do reset on watchdog */
+ tx3927_ccfgptr->ccfg |= TX3927_CCFG_WR;
+
+ printk(KERN_INFO "TX3927 -- CRIR:%08lx CCFG:%08lx PCFG:%08lx\n",
+ tx3927_ccfgptr->crir,
+ tx3927_ccfgptr->ccfg, tx3927_ccfgptr->pcfg);
+
+ /* TMR */
+ for (i = 0; i < TX3927_NR_TMR; i++)
+ txx9_tmr_init(TX3927_TMR_REG(i));
+
+ /* DMA */
+ tx3927_dmaptr->mcr = 0;
+ for (i = 0; i < ARRAY_SIZE(tx3927_dmaptr->ch); i++) {
+ /* reset channel */
+ tx3927_dmaptr->ch[i].ccr = TX3927_DMA_CCR_CHRST;
+ tx3927_dmaptr->ch[i].ccr = 0;
+ }
+ /* enable DMA */
+#ifdef __BIG_ENDIAN
+ tx3927_dmaptr->mcr = TX3927_DMA_MCR_MSTEN;
+#else
+ tx3927_dmaptr->mcr = TX3927_DMA_MCR_MSTEN | TX3927_DMA_MCR_LE;
+#endif
+
+ /* PIO */
+ __raw_writel(0, &tx3927_pioptr->maskcpu);
+ __raw_writel(0, &tx3927_pioptr->maskext);
+ txx9_gpio_init(TX3927_PIO_REG, 0, 16);
+
+ conf = read_c0_conf();
+ if (!(conf & TX39_CONF_ICE))
+ printk(KERN_INFO "TX3927 I-Cache disabled.\n");
+ if (!(conf & TX39_CONF_DCE))
+ printk(KERN_INFO "TX3927 D-Cache disabled.\n");
+ else if (!(conf & TX39_CONF_WBON))
+ printk(KERN_INFO "TX3927 D-Cache WriteThrough.\n");
+ else if (!(conf & TX39_CONF_CWFON))
+ printk(KERN_INFO "TX3927 D-Cache WriteBack.\n");
+ else
+ printk(KERN_INFO "TX3927 D-Cache WriteBack (CWF) .\n");
+}
+
+void __init tx3927_time_init(unsigned int evt_tmrnr, unsigned int src_tmrnr)
+{
+ txx9_clockevent_init(TX3927_TMR_REG(evt_tmrnr),
+ TXX9_IRQ_BASE + TX3927_IR_TMR(evt_tmrnr),
+ TXX9_IMCLK);
+ txx9_clocksource_init(TX3927_TMR_REG(src_tmrnr), TXX9_IMCLK);
+}
+
+void __init tx3927_setup_serial(unsigned int cts_mask)
+{
+#ifdef CONFIG_SERIAL_TXX9
+ int i;
+ struct uart_port req;
+
+ for (i = 0; i < 2; i++) {
+ memset(&req, 0, sizeof(req));
+ req.line = i;
+ req.iotype = UPIO_MEM;
+ req.membase = (unsigned char __iomem *)TX3927_SIO_REG(i);
+ req.mapbase = TX3927_SIO_REG(i);
+ req.irq = TXX9_IRQ_BASE + TX3927_IR_SIO(i);
+ if (!((1 << i) & cts_mask))
+ req.flags |= UPF_BUGGY_UART /*HAVE_CTS_LINE*/;
+ req.uartclk = TXX9_IMCLK;
+ early_serial_txx9_setup(&req);
+ }
+#endif /* CONFIG_SERIAL_TXX9 */
+}
#error JMR3927_IRQ_END > NR_IRQS
#endif
-static unsigned char irc_level[TX3927_NUM_IR] = {
- 5, 5, 5, 5, 5, 5, /* INT[5:0] */
- 7, 7, /* SIO */
- 5, 5, 5, 0, 0, /* DMA, PIO, PCI */
- 6, 6, 6 /* TMR */
-};
-
/*
* CP0_STATUS is a thread's resource (saved/restored on context switch).
* So disable_irq/enable_irq MUST handle IOC/IRC registers.
return irq;
}
-static void __init jmr3927_irq_init(void);
+static struct irq_chip jmr3927_irq_ioc = {
+ .name = "jmr3927_ioc",
+ .ack = mask_irq_ioc,
+ .mask = mask_irq_ioc,
+ .mask_ack = mask_irq_ioc,
+ .unmask = unmask_irq_ioc,
+};
void __init jmr3927_irq_setup(void)
{
+ int i;
+
txx9_irq_dispatch = jmr3927_irq_dispatch;
/* Now, interrupt control disabled, */
/* all IRC interrupts are masked, */
/* clear PCI Reset interrupts */
jmr3927_ioc_reg_out(0, JMR3927_IOC_RESET_ADDR);
- jmr3927_irq_init();
+ tx3927_irq_init();
+ for (i = JMR3927_IRQ_IOC; i < JMR3927_IRQ_IOC + JMR3927_NR_IRQ_IOC; i++)
+ set_irq_chip_and_handler(i, &jmr3927_irq_ioc, handle_level_irq);
/* setup IOC interrupt 1 (PCI, MODEM) */
set_irq_chained_handler(JMR3927_IRQ_IOCINT, handle_simple_irq);
-
- /* enable all CPU interrupt bits. */
- set_c0_status(ST0_IM); /* IE bit is still 0. */
-}
-
-static struct irq_chip jmr3927_irq_ioc = {
- .name = "jmr3927_ioc",
- .ack = mask_irq_ioc,
- .mask = mask_irq_ioc,
- .mask_ack = mask_irq_ioc,
- .unmask = unmask_irq_ioc,
-};
-
-static void __init jmr3927_irq_init(void)
-{
- u32 i;
-
- txx9_irq_init(TX3927_IRC_REG);
- for (i = 0; i < TXx9_MAX_IR; i++)
- txx9_irq_set_pri(i, irc_level[i]);
- for (i = JMR3927_IRQ_IOC; i < JMR3927_IRQ_IOC + JMR3927_NR_IRQ_IOC; i++)
- set_irq_chip_and_handler(i, &jmr3927_irq_ioc, handle_level_irq);
}
#include <linux/delay.h>
#include <linux/platform_device.h>
#include <linux/gpio.h>
-#ifdef CONFIG_SERIAL_TXX9
-#include <linux/serial_core.h>
-#endif
-#include <asm/txx9tmr.h>
-#include <asm/txx9pio.h>
#include <asm/reboot.h>
+#include <asm/txx9pio.h>
#include <asm/txx9/generic.h>
#include <asm/txx9/pci.h>
#include <asm/txx9/jmr3927.h>
#include <asm/mipsregs.h>
-/* don't enable - see errata */
-static int jmr3927_ccfg_toeon;
-
static void jmr3927_machine_restart(char *command)
{
local_irq_disable();
static void __init jmr3927_time_init(void)
{
- txx9_clockevent_init(TX3927_TMR_REG(0),
- JMR3927_IRQ_IRC_TMR(0),
- JMR3927_IMCLK);
- txx9_clocksource_init(TX3927_TMR_REG(1), JMR3927_IMCLK);
+ tx3927_time_init(0, 1);
}
#define DO_WRITE_THROUGH
jmr3927_board_init();
argptr = prom_getcmdline();
-
- if ((argptr = strstr(argptr, "toeon")) != NULL)
- jmr3927_ccfg_toeon = 1;
- argptr = prom_getcmdline();
if ((argptr = strstr(argptr, "ip=")) == NULL) {
argptr = prom_getcmdline();
strcat(argptr, " ip=bootp");
}
-#ifdef CONFIG_SERIAL_TXX9
- {
- extern int early_serial_txx9_setup(struct uart_port *port);
- int i;
- struct uart_port req;
- for(i = 0; i < 2; i++) {
- memset(&req, 0, sizeof(req));
- req.line = i;
- req.iotype = UPIO_MEM;
- req.membase = (unsigned char __iomem *)TX3927_SIO_REG(i);
- req.mapbase = TX3927_SIO_REG(i);
- req.irq = i == 0 ?
- JMR3927_IRQ_IRC_SIO0 : JMR3927_IRQ_IRC_SIO1;
- if (i == 0)
- req.flags |= UPF_BUGGY_UART /*HAVE_CTS_LINE*/;
- req.uartclk = JMR3927_IMCLK;
- early_serial_txx9_setup(&req);
- }
- }
+ tx3927_setup_serial(1 << 1); /* ch1: noCTS */
#ifdef CONFIG_SERIAL_TXX9_CONSOLE
argptr = prom_getcmdline();
if ((argptr = strstr(argptr, "console=")) == NULL) {
strcat(argptr, " console=ttyS1,115200");
}
#endif
-#endif
}
-static void tx3927_setup(void);
-
static void __init jmr3927_pci_setup(void)
{
#ifdef CONFIG_PCI
static void __init jmr3927_board_init(void)
{
- tx3927_setup();
- jmr3927_pci_setup();
-
- /* SIO0 DTR on */
- jmr3927_ioc_reg_out(0, JMR3927_IOC_DTR_ADDR);
-
- jmr3927_led_set(0);
-
- printk("JMR-TX3927 (Rev %d) --- IOC(Rev %d) DIPSW:%d,%d,%d,%d\n",
- jmr3927_ioc_reg_in(JMR3927_IOC_BREV_ADDR) & JMR3927_REV_MASK,
- jmr3927_ioc_reg_in(JMR3927_IOC_REV_ADDR) & JMR3927_REV_MASK,
- jmr3927_dipsw1(), jmr3927_dipsw2(),
- jmr3927_dipsw3(), jmr3927_dipsw4());
-}
-
-static void __init tx3927_setup(void)
-{
- int i;
-
txx9_cpu_clock = JMR3927_CORECLK;
- txx9_gbus_clock = JMR3927_GBUSCLK;
/* SDRAMC are configured by PROM */
/* ROMC */
tx3927_romcptr->cr[3] = JMR3927_ROMCE3 | 0x0003f698;
tx3927_romcptr->cr[5] = JMR3927_ROMCE5 | 0x0000f218;
- /* CCFG */
- /* enable Timeout BusError */
- if (jmr3927_ccfg_toeon)
- tx3927_ccfgptr->ccfg |= TX3927_CCFG_TOE;
-
- /* clear BusErrorOnWrite flag */
- tx3927_ccfgptr->ccfg &= ~TX3927_CCFG_BEOW;
- /* Disable PCI snoop */
- tx3927_ccfgptr->ccfg &= ~TX3927_CCFG_PSNP;
- /* do reset on watchdog */
- tx3927_ccfgptr->ccfg |= TX3927_CCFG_WR;
-
-#ifdef DO_WRITE_THROUGH
- /* Enable PCI SNOOP - with write through only */
- tx3927_ccfgptr->ccfg |= TX3927_CCFG_PSNP;
-#endif
-
/* Pin selection */
tx3927_ccfgptr->pcfg &= ~TX3927_PCFG_SELALL;
tx3927_ccfgptr->pcfg |=
TX3927_PCFG_SELSIOC(0) | TX3927_PCFG_SELSIO_ALL |
(TX3927_PCFG_SELDMA_ALL & ~TX3927_PCFG_SELDMA(1));
- printk("TX3927 -- CRIR:%08lx CCFG:%08lx PCFG:%08lx\n",
- tx3927_ccfgptr->crir,
- tx3927_ccfgptr->ccfg, tx3927_ccfgptr->pcfg);
-
- /* TMR */
- for (i = 0; i < TX3927_NR_TMR; i++)
- txx9_tmr_init(TX3927_TMR_REG(i));
-
- /* DMA */
- tx3927_dmaptr->mcr = 0;
- for (i = 0; i < ARRAY_SIZE(tx3927_dmaptr->ch); i++) {
- /* reset channel */
- tx3927_dmaptr->ch[i].ccr = TX3927_DMA_CCR_CHRST;
- tx3927_dmaptr->ch[i].ccr = 0;
- }
- /* enable DMA */
-#ifdef __BIG_ENDIAN
- tx3927_dmaptr->mcr = TX3927_DMA_MCR_MSTEN;
-#else
- tx3927_dmaptr->mcr = TX3927_DMA_MCR_MSTEN | TX3927_DMA_MCR_LE;
-#endif
+ tx3927_setup();
- /* PIO */
/* PIO[15:12] connected to LEDs */
__raw_writel(0x0000f000, &tx3927_pioptr->dir);
- __raw_writel(0, &tx3927_pioptr->maskcpu);
- __raw_writel(0, &tx3927_pioptr->maskext);
- txx9_gpio_init(TX3927_PIO_REG, 0, 16);
gpio_request(11, "dipsw1");
gpio_request(10, "dipsw2");
- {
- unsigned int conf;
- conf = read_c0_conf();
- if (!(conf & TX39_CONF_ICE))
- printk("TX3927 I-Cache disabled.\n");
- if (!(conf & TX39_CONF_DCE))
- printk("TX3927 D-Cache disabled.\n");
- else if (!(conf & TX39_CONF_WBON))
- printk("TX3927 D-Cache WriteThrough.\n");
- else if (!(conf & TX39_CONF_CWFON))
- printk("TX3927 D-Cache WriteBack.\n");
- else
- printk("TX3927 D-Cache WriteBack (CWF) .\n");
- }
+ jmr3927_pci_setup();
+
+ /* SIO0 DTR on */
+ jmr3927_ioc_reg_out(0, JMR3927_IOC_DTR_ADDR);
+
+ jmr3927_led_set(0);
+
+ printk(KERN_INFO
+ "JMR-TX3927 (Rev %d) --- IOC(Rev %d) DIPSW:%d,%d,%d,%d\n",
+ jmr3927_ioc_reg_in(JMR3927_IOC_BREV_ADDR) & JMR3927_REV_MASK,
+ jmr3927_ioc_reg_in(JMR3927_IOC_REV_ADDR) & JMR3927_REV_MASK,
+ jmr3927_dipsw1(), jmr3927_dipsw2(),
+ jmr3927_dipsw3(), jmr3927_dipsw4());
}
/* This trick makes rtc-ds1742 driver usable as is. */
return IS_ERR(dev) ? PTR_ERR(dev) : 0;
}
-static void __init tx3927_wdt_init(void)
-{
- txx9_wdt_init(TX3927_TMR_REG(2));
-}
-
static void __init jmr3927_device_init(void)
{
__swizzle_addr_b = jmr3927_swizzle_addr_b;
/* Clocks */
#define JMR3927_CORECLK 132710400 /* 132.7MHz */
-#define JMR3927_GBUSCLK (JMR3927_CORECLK / 2) /* 66.35MHz */
-#define JMR3927_IMCLK (JMR3927_CORECLK / 4) /* 33.17MHz */
/*
* TX3927 Pin Configuration:
#include <asm/txx9/txx927.h>
#define TX3927_REG_BASE 0xfffe0000UL
+#define TX3927_REG_SIZE 0x00010000
#define TX3927_SDRAMC_REG (TX3927_REG_BASE + 0x8000)
#define TX3927_ROMC_REG (TX3927_REG_BASE + 0x9000)
#define TX3927_DMA_REG (TX3927_REG_BASE + 0xb000)
#define tx3927_dmaptr ((struct tx3927_dma_reg *)TX3927_DMA_REG)
#define tx3927_pcicptr ((struct tx3927_pcic_reg *)TX3927_PCIC_REG)
#define tx3927_ccfgptr ((struct tx3927_ccfg_reg *)TX3927_CCFG_REG)
-#define tx3927_tmrptr(ch) ((struct txx927_tmr_reg *)TX3927_TMR_REG(ch))
#define tx3927_sioptr(ch) ((struct txx927_sio_reg *)TX3927_SIO_REG(ch))
#define tx3927_pioptr ((struct txx9_pio_reg __iomem *)TX3927_PIO_REG)
+#define TX3927_REV_PCODE() (tx3927_ccfgptr->crir >> 16)
+#define TX3927_ROMC_BA(ch) (tx3927_romcptr->cr[(ch)] & 0xfff00000)
+#define TX3927_ROMC_SIZE(ch) \
+ (0x00100000 << ((tx3927_romcptr->cr[(ch)] >> 8) & 0xf))
+
+void tx3927_wdt_init(void);
+void tx3927_setup(void);
+void tx3927_time_init(unsigned int evt_tmrnr, unsigned int src_tmrnr);
+void tx3927_setup_serial(unsigned int cts_mask);
struct pci_controller;
void __init tx3927_pcic_setup(struct pci_controller *channel,
unsigned long sdram_size, int extarb);
void tx3927_setup_pcierr_irq(void);
+void tx3927_irq_init(void);
#endif /* __ASM_TXX9_TX3927_H */
projects / linux-2.6 / commitdiff