to the kernel, you may specify one here. As a minimum, you should specify
the memory size and the root device (e.g., mem=8M, root=/dev/nfs).
-comment "Board Setup"
+comment "Clock/PLL Setup"
config CLKIN_HZ
int "Crystal Frequency in Hz"
help
The frequency of CLKIN crystal oscillator on the board in Hz.
+config BFIN_KERNEL_CLOCK
+ bool "Re-program Clocks while Kernel boots?"
+ default n
+ help
+ This option decides if kernel clocks are re-programed from the
+ bootloader settings. If the clocks are not set, the SDRAM settings
+ are also not changed, and the Bootloader does 100% of the hardware
+ configuration.
+
+config PLL_BYPASS
+ bool "Bypass PLL"
+ depends on BFIN_KERNEL_CLOCK
+ default n
+
+config CLKIN_HALF
+ bool "Half Clock In"
+ depends on BFIN_KERNEL_CLOCK && (! PLL_BYPASS)
+ default n
+ help
+ If this is set the clock will be divided by 2, before it goes to the PLL.
+
+config VCO_MULT
+ int "VCO Multiplier"
+ depends on BFIN_KERNEL_CLOCK && (! PLL_BYPASS)
+ range 1 64
+ default "22" if BFIN533_EZKIT
+ default "45" if BFIN533_STAMP
+ default "20" if BFIN537_STAMP
+ default "22" if BFIN533_BLUETECHNIX_CM
+ default "20" if BFIN537_BLUETECHNIX_CM
+ default "20" if BFIN561_BLUETECHNIX_CM
+ default "20" if BFIN561_EZKIT
+ help
+ This controls the frequency of the on-chip PLL. This can be between 1 and 64.
+ PLL Frequency = (Crystal Frequency) * (this setting)
+
+choice
+ prompt "Core Clock Divider"
+ depends on BFIN_KERNEL_CLOCK
+ default CCLK_DIV_1
+ help
+ This sets the frequency of the core. It can be 1, 2, 4 or 8
+ Core Frequency = (PLL frequency) / (this setting)
+
+config CCLK_DIV_1
+ bool "1"
+
+config CCLK_DIV_2
+ bool "2"
+
+config CCLK_DIV_4
+ bool "4"
+
+config CCLK_DIV_8
+ bool "8"
+endchoice
+
+config SCLK_DIV
+ int "System Clock Divider"
+ depends on BFIN_KERNEL_CLOCK
+ range 1 15
+ default 5 if BFIN533_EZKIT
+ default 5 if BFIN533_STAMP
+ default 4 if BFIN537_STAMP
+ default 5 if BFIN533_BLUETECHNIX_CM
+ default 4 if BFIN537_BLUETECHNIX_CM
+ default 4 if BFIN561_BLUETECHNIX_CM
+ default 5 if BFIN561_EZKIT
+ help
+ This sets the frequency of the system clock (including SDRAM or DDR).
+ This can be between 1 and 15
+ System Clock = (PLL frequency) / (this setting)
+
+#
+# Max & Min Speeds for various Chips
+#
+config MAX_VCO_HZ
+ int
+ default 600000000 if BF522
+ default 600000000 if BF525
+ default 600000000 if BF527
+ default 400000000 if BF531
+ default 400000000 if BF532
+ default 750000000 if BF533
+ default 500000000 if BF534
+ default 400000000 if BF536
+ default 600000000 if BF537
+ default 533000000 if BF538
+ default 533000000 if BF539
+ default 600000000 if BF542
+ default 533000000 if BF544
+ default 533000000 if BF549
+ default 600000000 if BF561
+
+config MIN_VCO_HZ
+ int
+ default 50000000
+
+config MAX_SCLK_HZ
+ int
+ default 133000000
+
+config MIN_SCLK_HZ
+ int
+ default 27000000
+
+comment "Kernel Timer/Scheduler"
+
+source kernel/Kconfig.hz
+
+comment "Memory Setup"
+
config MEM_SIZE
int "SDRAM Memory Size in MBytes"
default 32 if BFIN533_EZKIT
menu "Blackfin Kernel Optimizations"
-comment "Timer Tick"
-
-source kernel/Kconfig.hz
-
comment "Memory Optimizations"
config I_ENTRY_L1
Set the max memory pieces for the L1 SRAM allocation algorithm.
Min value is 16. Max value is 1024.
-menu "Clock Settings"
-
-
-config BFIN_KERNEL_CLOCK
- bool "Re-program Clocks while Kernel boots?"
- default n
- help
- This option decides if kernel clocks are re-programed from the
- bootloader settings. If the clocks are not set, the SDRAM settings
- are also not changed, and the Bootloader does 100% of the hardware
- configuration.
-
-config VCO_MULT
- int "VCO Multiplier"
- depends on BFIN_KERNEL_CLOCK
- default "22" if BFIN533_EZKIT
- default "45" if BFIN533_STAMP
- default "20" if BFIN537_STAMP
- default "22" if BFIN533_BLUETECHNIX_CM
- default "20" if BFIN537_BLUETECHNIX_CM
- default "20" if BFIN561_BLUETECHNIX_CM
- default "20" if BFIN561_EZKIT
-
-config CCLK_DIV
- int "Core Clock Divider"
- depends on BFIN_KERNEL_CLOCK
- default 1 if BFIN533_EZKIT
- default 1 if BFIN533_STAMP
- default 1 if BFIN537_STAMP
- default 1 if BFIN533_BLUETECHNIX_CM
- default 1 if BFIN537_BLUETECHNIX_CM
- default 1 if BFIN561_BLUETECHNIX_CM
- default 1 if BFIN561_EZKIT
-
-config SCLK_DIV
- int "System Clock Divider"
- depends on BFIN_KERNEL_CLOCK
- default 5 if BFIN533_EZKIT
- default 5 if BFIN533_STAMP
- default 4 if BFIN537_STAMP
- default 5 if BFIN533_BLUETECHNIX_CM
- default 4 if BFIN537_BLUETECHNIX_CM
- default 4 if BFIN561_BLUETECHNIX_CM
- default 5 if BFIN561_EZKIT
-
-config CLKIN_HALF
- bool "Half ClockIn"
- depends on BFIN_KERNEL_CLOCK
- default n
-
-config PLL_BYPASS
- bool "Bypass PLL"
- depends on BFIN_KERNEL_CLOCK
- default n
-
-endmenu
-
comment "Asynchonous Memory Configuration"
menu "EBIU_AMBCTL Global Control"
#include <asm/blackfin.h>
#include <asm/trace.h>
#if CONFIG_BFIN_KERNEL_CLOCK
+#include <asm/mach-common/clocks.h>
#include <asm/mach/mem_init.h>
#endif
#if CONFIG_DEBUG_KERNEL_START
#include <asm/trace.h>
#if CONFIG_BFIN_KERNEL_CLOCK
+#include <asm/mach-common/clocks.h>
#include <asm/mach/mem_init.h>
#endif
#include <asm/blackfin.h>
#include <asm/trace.h>
#if CONFIG_BFIN_KERNEL_CLOCK
+#include <asm/mach-common/clocks.h>
#include <asm/mach/mem_init.h>
#endif
#include <asm/trace.h>
#if CONFIG_BFIN_KERNEL_CLOCK
+#include <asm/mach-common/clocks.h>
#include <asm/mach/mem_init.h>
#endif
obj-y := \
cache.o cacheinit.o cplbhdlr.o cplbmgr.o entry.o \
- interrupt.o lock.o irqpanic.o
+ interrupt.o lock.o irqpanic.o arch_checks.o
obj-$(CONFIG_CPLB_INFO) += cplbinfo.o
obj-$(CONFIG_BFIN_SINGLE_CORE) += ints-priority-sc.o
--- /dev/null
+/*
+ * File: arch/blackfin/mach-common/arch_checks.c
+ * Based on:
+ * Author: Robin Getz <rgetz@blackfin.uclinux.org>
+ *
+ * Created: 25Jul07
+ * Description: Do some checking to make sure things are OK
+ *
+ * Modified:
+ * Copyright 2004-2007 Analog Devices Inc.
+ *
+ * Bugs: Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see the file COPYING, or write
+ * to the Free Software Foundation, Inc.,
+ * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <asm/mach/anomaly.h>
+#include <asm/mach-common/clocks.h>
+
+#ifdef CONFIG_BFIN_KERNEL_CLOCK
+
+# if (CONFIG_VCO_HZ > CONFIG_MAX_VCO_HZ)
+# error "VCO selected is more than maximum value. Please change the VCO multipler"
+# endif
+
+# if (CONFIG_SCLK_HZ > CONFIG_MAX_SCLK_HZ)
+# error "Sclk value selected is more than maximum. Please select a proper value for SCLK multiplier"
+# endif
+
+# if (CONFIG_SCLK_HZ < CONFIG_MIN_SCLK_HZ)
+# error "Sclk value selected is less than minimum. Please select a proper value for SCLK multiplier"
+# endif
+
+# if (ANOMALY_05000273) && (CONFIG_SCLK_HZ * 2 > CONFIG_CCLK_HZ)
+# error "ANOMALY 05000273, please make sure CCLK is at least 2x SCLK"
+# endif
+
+# if (CONFIG_SCLK_HZ > CONFIG_CCLK_HZ) && (CONFIG_SCLK_HZ != CONFIG_CLKIN_HZ) && (CONFIG_CCLK_HZ != CONFIG_CLKIN_HZ)
+# error "Please select sclk less than cclk"
+# endif
+
+#endif /* CONFIG_BFIN_KERNEL_CLOCK */
P0.H = hi(PLL_CTL);
P0.L = lo(PLL_CTL);
R5 = W[P0](z);
- R0.L = (MIN_VC/CONFIG_CLKIN_HZ) << 9;
+ R0.L = (CONFIG_MIN_VCO_HZ/CONFIG_CLKIN_HZ) << 9;
W[P0] = R0.l;
SSYNC;
#define AMGCTLVAL (V_AMBEN | V_AMCKEN | V_CDPRIO)
-#define MAX_VC 650000000
-#define MIN_VC 50000000
-
-#ifdef CONFIG_BFIN_KERNEL_CLOCK
-/********************************PLL Settings **************************************/
-#if (CONFIG_VCO_MULT < 0)
-#error "VCO Multiplier is less than 0. Please select a different value"
-#endif
-
-#if (CONFIG_VCO_MULT == 0)
-#error "VCO Multiplier should be greater than 0. Please select a different value"
-#endif
-
-#if (CONFIG_VCO_MULT > 64)
-#error "VCO Multiplier is more than 64. Please select a different value"
-#endif
-
-#ifndef CONFIG_CLKIN_HALF
-#define CONFIG_VCO_HZ (CONFIG_CLKIN_HZ * CONFIG_VCO_MULT)
-#else
-#define CONFIG_VCO_HZ ((CONFIG_CLKIN_HZ * CONFIG_VCO_MULT)/2)
-#endif
-
-#ifndef CONFIG_PLL_BYPASS
-#define CONFIG_CCLK_HZ (CONFIG_VCO_HZ/CONFIG_CCLK_DIV)
-#define CONFIG_SCLK_HZ (CONFIG_VCO_HZ/CONFIG_SCLK_DIV)
-#else
-#define CONFIG_CCLK_HZ CONFIG_CLKIN_HZ
-#define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ
-#endif
-
-#if (CONFIG_SCLK_DIV < 1)
-#error "SCLK DIV cannot be less than 1 or more than 15. Please select a proper value"
-#endif
-
-#if (CONFIG_SCLK_DIV > 15)
-#error "SCLK DIV cannot be less than 1 or more than 15. Please select a proper value"
-#endif
-
-#if (CONFIG_CCLK_DIV != 1)
-#if (CONFIG_CCLK_DIV != 2)
-#if (CONFIG_CCLK_DIV != 4)
-#if (CONFIG_CCLK_DIV != 8)
-#error "CCLK DIV can be 1,2,4 or 8 only. Please select a proper value"
-#endif
-#endif
-#endif
-#endif
-
-#if (CONFIG_VCO_HZ > MAX_VC)
-#error "VCO selected is more than maximum value. Please change the VCO multipler"
-#endif
-
-#if (CONFIG_SCLK_HZ > 133000000)
-#error "Sclk value selected is more than maximum. Please select a proper value for SCLK multiplier"
-#endif
-
-#if (CONFIG_SCLK_HZ < 27000000)
-#error "Sclk value selected is less than minimum. Please select a proper value for SCLK multiplier"
-#endif
-
-#if (CONFIG_SCLK_HZ > CONFIG_CCLK_HZ)
-#if (CONFIG_SCLK_HZ != CONFIG_CLKIN_HZ)
-#if (CONFIG_CCLK_HZ != CONFIG_CLKIN_HZ)
-#error "Please select sclk less than cclk"
-#endif
-#endif
-#endif
-
-#if (CONFIG_CCLK_DIV == 1)
-#define CONFIG_CCLK_ACT_DIV CCLK_DIV1
-#endif
-#if (CONFIG_CCLK_DIV == 2)
-#define CONFIG_CCLK_ACT_DIV CCLK_DIV2
-#endif
-#if (CONFIG_CCLK_DIV == 4)
-#define CONFIG_CCLK_ACT_DIV CCLK_DIV4
-#endif
-#if (CONFIG_CCLK_DIV == 8)
-#define CONFIG_CCLK_ACT_DIV CCLK_DIV8
-#endif
-#ifndef CONFIG_CCLK_ACT_DIV
-#define CONFIG_CCLK_ACT_DIV CONFIG_CCLK_DIV_not_defined_properly
-#endif
-
-#if ANOMALY_05000273 && (CONFIG_CCLK_DIV == 1)
-#error ANOMALY 05000273, please make sure CCLK is at least 2x SCLK
-#endif
-
-#endif /* CONFIG_BFIN_KERNEL_CLOCK */
-
#ifdef CONFIG_BF533
#define CPU "BF533"
#define CPUID 0x027a5000
#define AMGCTLVAL (V_AMBEN | V_AMCKEN | V_CDPRIO)
-#define MAX_VC 650000000
-#define MIN_VC 50000000
-
-/********************************PLL Settings **************************************/
-#ifdef CONFIG_BFIN_KERNEL_CLOCK
-#if (CONFIG_VCO_MULT < 0)
-#error "VCO Multiplier is less than 0. Please select a different value"
-#endif
-
-#if (CONFIG_VCO_MULT == 0)
-#error "VCO Multiplier should be greater than 0. Please select a different value"
-#endif
-
-#if (CONFIG_VCO_MULT > 64)
-#error "VCO Multiplier is more than 64. Please select a different value"
-#endif
-
-#ifndef CONFIG_CLKIN_HALF
-#define CONFIG_VCO_HZ (CONFIG_CLKIN_HZ * CONFIG_VCO_MULT)
-#else
-#define CONFIG_VCO_HZ ((CONFIG_CLKIN_HZ * CONFIG_VCO_MULT)/2)
-#endif
-
-#ifndef CONFIG_PLL_BYPASS
-#define CONFIG_CCLK_HZ (CONFIG_VCO_HZ/CONFIG_CCLK_DIV)
-#define CONFIG_SCLK_HZ (CONFIG_VCO_HZ/CONFIG_SCLK_DIV)
-#else
-#define CONFIG_CCLK_HZ CONFIG_CLKIN_HZ
-#define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ
-#endif
-
-#if (CONFIG_SCLK_DIV < 1)
-#error "SCLK DIV cannot be less than 1 or more than 15. Please select a proper value"
-#endif
-
-#if (CONFIG_SCLK_DIV > 15)
-#error "SCLK DIV cannot be less than 1 or more than 15. Please select a proper value"
-#endif
-
-#if (CONFIG_CCLK_DIV != 1)
-#if (CONFIG_CCLK_DIV != 2)
-#if (CONFIG_CCLK_DIV != 4)
-#if (CONFIG_CCLK_DIV != 8)
-#error "CCLK DIV can be 1,2,4 or 8 only. Please select a proper value"
-#endif
-#endif
-#endif
-#endif
-
-#if (CONFIG_VCO_HZ > MAX_VC)
-#error "VCO selected is more than maximum value. Please change the VCO multipler"
-#endif
-
-#if (CONFIG_SCLK_HZ > 133000000)
-#error "Sclk value selected is more than maximum. Please select a proper value for SCLK multiplier"
-#endif
-
-#if (CONFIG_SCLK_HZ < 27000000)
-#error "Sclk value selected is less than minimum. Please select a proper value for SCLK multiplier"
-#endif
-
-#if (CONFIG_SCLK_HZ >= CONFIG_CCLK_HZ)
-#if (CONFIG_SCLK_HZ != CONFIG_CLKIN_HZ)
-#if (CONFIG_CCLK_HZ != CONFIG_CLKIN_HZ)
-#error "Please select sclk less than cclk"
-#endif
-#endif
-#endif
-
-#if (CONFIG_CCLK_DIV == 1)
-#define CONFIG_CCLK_ACT_DIV CCLK_DIV1
-#endif
-#if (CONFIG_CCLK_DIV == 2)
-#define CONFIG_CCLK_ACT_DIV CCLK_DIV2
-#endif
-#if (CONFIG_CCLK_DIV == 4)
-#define CONFIG_CCLK_ACT_DIV CCLK_DIV4
-#endif
-#if (CONFIG_CCLK_DIV == 8)
-#define CONFIG_CCLK_ACT_DIV CCLK_DIV8
-#endif
-#ifndef CONFIG_CCLK_ACT_DIV
-#define CONFIG_CCLK_ACT_DIV CONFIG_CCLK_DIV_not_defined_properly
-#endif
-
-#if ANOMALY_05000273 && (CONFIG_CCLK_DIV == 1)
-#error ANOMALY 05000273, please make sure CCLK is at least 2x SCLK
-#endif
-
-#endif /* CONFIG_BFIN_KERNEL_CLOCK */
-
#ifdef CONFIG_BF537
#define CPU "BF537"
#define CPUID 0x027c8000
#define AMGCTLVAL (V_AMBEN | V_AMCKEN)
-#define MAX_VC 650000000
-#define MIN_VC 50000000
-
-/********************************PLL Settings **************************************/
-#ifdef CONFIG_BFIN_KERNEL_CLOCK
-#if (CONFIG_VCO_MULT < 0)
-#error "VCO Multiplier is less than 0. Please select a different value"
-#endif
-
-#if (CONFIG_VCO_MULT == 0)
-#error "VCO Multiplier should be greater than 0. Please select a different value"
-#endif
-
-#if (CONFIG_VCO_MULT > 64)
-#error "VCO Multiplier is more than 64. Please select a different value"
-#endif
-
-#ifndef CONFIG_CLKIN_HALF
-#define CONFIG_VCO_HZ (CONFIG_CLKIN_HZ * CONFIG_VCO_MULT)
-#else
-#define CONFIG_VCO_HZ ((CONFIG_CLKIN_HZ * CONFIG_VCO_MULT)/2)
-#endif
-
-#ifndef CONFIG_PLL_BYPASS
-#define CONFIG_CCLK_HZ (CONFIG_VCO_HZ/CONFIG_CCLK_DIV)
-#define CONFIG_SCLK_HZ (CONFIG_VCO_HZ/CONFIG_SCLK_DIV)
-#else
-#define CONFIG_CCLK_HZ CONFIG_CLKIN_HZ
-#define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ
-#endif
-
-#if (CONFIG_SCLK_DIV < 1)
-#error "SCLK DIV cannot be less than 1 or more than 15. Please select a proper value"
-#endif
-
-#if (CONFIG_SCLK_DIV > 15)
-#error "SCLK DIV cannot be less than 1 or more than 15. Please select a proper value"
-#endif
-
-#if (CONFIG_CCLK_DIV != 1)
-#if (CONFIG_CCLK_DIV != 2)
-#if (CONFIG_CCLK_DIV != 4)
-#if (CONFIG_CCLK_DIV != 8)
-#error "CCLK DIV can be 1,2,4 or 8 only. Please select a proper value"
-#endif
-#endif
-#endif
-#endif
-
-#if (CONFIG_VCO_HZ > MAX_VC)
-#error "VCO selected is more than maximum value. Please change the VCO multipler"
-#endif
-
-#if (CONFIG_SCLK_HZ > 133000000)
-#error "Sclk value selected is more than maximum. Please select a proper value for SCLK multiplier"
-#endif
-
-#if (CONFIG_SCLK_HZ < 27000000)
-#error "Sclk value selected is less than minimum. Please select a proper value for SCLK multiplier"
-#endif
-
-#if (CONFIG_SCLK_HZ >= CONFIG_CCLK_HZ)
-#if (CONFIG_SCLK_HZ != CONFIG_CLKIN_HZ)
-#if (CONFIG_CCLK_HZ != CONFIG_CLKIN_HZ)
-#error "Please select sclk less than cclk"
-#endif
-#endif
-#endif
-
-#if (CONFIG_CCLK_DIV == 1)
-#define CONFIG_CCLK_ACT_DIV CCLK_DIV1
-#endif
-#if (CONFIG_CCLK_DIV == 2)
-#define CONFIG_CCLK_ACT_DIV CCLK_DIV2
-#endif
-#if (CONFIG_CCLK_DIV == 4)
-#define CONFIG_CCLK_ACT_DIV CCLK_DIV4
-#endif
-#if (CONFIG_CCLK_DIV == 8)
-#define CONFIG_CCLK_ACT_DIV CCLK_DIV8
-#endif
-#ifndef CONFIG_CCLK_ACT_DIV
-#define CONFIG_CCLK_ACT_DIV CONFIG_CCLK_DIV_not_defined_properly
-#endif
-
-#endif /* CONFIG_BFIN_KERNEL_CLOCK */
-
#ifdef CONFIG_BF542
#define CPU "BF542"
#define CPUID 0x027c8000
#define AMGCTLVAL (V_AMBEN | V_AMCKEN | V_CDPRIO | V_B0PEN | V_B1PEN | V_B2PEN | V_B3PEN | 0x0002)
-#define MAX_VC 600000000
-#define MIN_VC 50000000
-
-/******************************* PLL Settings ********************************/
-#ifdef CONFIG_BFIN_KERNEL_CLOCK
-#if (CONFIG_VCO_MULT < 0)
-#error "VCO Multiplier is less than 0. Please select a different value"
-#endif
-
-#if (CONFIG_VCO_MULT == 0)
-#error "VCO Multiplier should be greater than 0. Please select a different value"
-#endif
-
-#ifndef CONFIG_CLKIN_HALF
-#define CONFIG_VCO_HZ (CONFIG_CLKIN_HZ * CONFIG_VCO_MULT)
-#else
-#define CONFIG_VCO_HZ ((CONFIG_CLKIN_HZ * CONFIG_VCO_MULT)/2)
-#endif
-
-#ifndef CONFIG_PLL_BYPASS
-#define CONFIG_CCLK_HZ (CONFIG_VCO_HZ/CONFIG_CCLK_DIV)
-#define CONFIG_SCLK_HZ (CONFIG_VCO_HZ/CONFIG_SCLK_DIV)
-#else
-#define CONFIG_CCLK_HZ CONFIG_CLKIN_HZ
-#define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ
-#endif
-
-#if (CONFIG_SCLK_DIV < 1)
-#error "SCLK DIV cannot be less than 1 or more than 15. Please select a proper value"
-#endif
-
-#if (CONFIG_SCLK_DIV > 15)
-#error "SCLK DIV cannot be less than 1 or more than 15. Please select a proper value"
-#endif
-
-#if (CONFIG_CCLK_DIV != 1)
-#if (CONFIG_CCLK_DIV != 2)
-#if (CONFIG_CCLK_DIV != 4)
-#if (CONFIG_CCLK_DIV != 8)
-#error "CCLK DIV can be 1,2,4 or 8 only. Please select a proper value"
-#endif
-#endif
-#endif
-#endif
-
-#if (CONFIG_VCO_HZ > MAX_VC)
-#error "VCO selected is more than maximum value. Please change the VCO multipler"
-#endif
-
-#if (CONFIG_SCLK_HZ > 133000000)
-#error "Sclk value selected is more than maximum. Please select a proper value for SCLK multiplier"
-#endif
-
-#if (CONFIG_SCLK_HZ < 27000000)
-#error "Sclk value selected is less than minimum. Please select a proper value for SCLK multiplier"
-#endif
-
-#if (CONFIG_SCLK_HZ >= CONFIG_CCLK_HZ)
-#if (CONFIG_SCLK_HZ != CONFIG_CLKIN_HZ)
-#if (CONFIG_CCLK_HZ != CONFIG_CLKIN_HZ)
-#error "Please select sclk less than cclk"
-#endif
-#endif
-#endif
-
-#if (CONFIG_CCLK_DIV == 1)
-#define CONFIG_CCLK_ACT_DIV CCLK_DIV1
-#endif
-#if (CONFIG_CCLK_DIV == 2)
-#define CONFIG_CCLK_ACT_DIV CCLK_DIV2
-#endif
-#if (CONFIG_CCLK_DIV == 4)
-#define CONFIG_CCLK_ACT_DIV CCLK_DIV4
-#endif
-#if (CONFIG_CCLK_DIV == 8)
-#define CONFIG_CCLK_ACT_DIV CCLK_DIV8
-#endif
-#ifndef CONFIG_CCLK_ACT_DIV
-#define CONFIG_CCLK_ACT_DIV CONFIG_CCLK_DIV_not_defined_properly
-#endif
-
-#if ANOMALY_05000273 && (CONFIG_CCLK_DIV == 1)
-#error ANOMALY 05000273, please make sure CCLK is at least 2x SCLK
-#endif
-
-#endif /* CONFIG_BFIN_KERNEL_CLOCK */
-
#ifdef CONFIG_BF561
#define CPU "BF561"
#define CPUID 0x027bb000
--- /dev/null
+/*
+ * File: include/asm-blackfin/mach-common/clocks.h
+ * Based on: include/asm-blackfin/mach-bf537/bf537.h
+ * Author: Robin Getz <rgetz@blackfin.uclinux.org>
+ *
+ * Created: 25Jul07
+ * Description: Common Clock definitions for various kernel files
+ *
+ * Modified:
+ * Copyright 2004-2007 Analog Devices Inc.
+ *
+ * Bugs: Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see the file COPYING, or write
+ * to the Free Software Foundation, Inc.,
+ * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+
+
+#ifdef CONFIG_CCLK_DIV_1
+# define CONFIG_CCLK_ACT_DIV CCLK_DIV1
+# define CONFIG_CCLK_DIV 1
+#endif
+
+#ifdef CONFIG_CCLK_DIV_2
+# define CONFIG_CCLK_ACT_DIV CCLK_DIV2
+# define CONFIG_CCLK_DIV 2
+#endif
+
+#ifdef CONFIG_CCLK_DIV_4
+# define CONFIG_CCLK_ACT_DIV CCLK_DIV4
+# define CONFIG_CCLK_DIV 4
+#endif
+
+#ifdef CONFIG_CCLK_DIV_8
+# define CONFIG_CCLK_ACT_DIV CCLK_DIV8
+# define CONFIG_CCLK_DIV 8
+#endif
+
+#ifndef CONFIG_PLL_BYPASS
+# ifndef CONFIG_CLKIN_HALF
+# define CONFIG_VCO_HZ (CONFIG_CLKIN_HZ * CONFIG_VCO_MULT)
+# else
+# define CONFIG_VCO_HZ ((CONFIG_CLKIN_HZ * CONFIG_VCO_MULT)/2)
+# endif
+
+# define CONFIG_CCLK_HZ (CONFIG_VCO_HZ/CONFIG_CCLK_DIV)
+# define CONFIG_SCLK_HZ (CONFIG_VCO_HZ/CONFIG_SCLK_DIV)
+
+#else
+# define CONFIG_VCO_HZ (CONFIG_CLKIN_HZ)
+# define CONFIG_CCLK_HZ (CONFIG_CLKIN_HZ)
+# define CONFIG_SCLK_HZ (CONFIG_CLKIN_HZ)
+# define CONFIG_VCO_MULT 0
+#endif
+
projects / linux-2.6 / commitdiff