CRIS v10: Correct and cleanup boot/rescue/kimagerescue.S

- Correct include path for sv_addr_ag.h, should be included from asm/arch/
- Remove useless CVS id tag.
- Correct whitespace errors and some formatting.

diff --git a/arch/cris/arch-v10/boot/rescue/kimagerescue.S b/arch/cris/arch-v10/boot/rescue/kimagerescue.S
index cbccd6316d3908ab12179b52be0bdf6fbd0cc74c..55eeff8bb08ea6ca5d6c36278cadf34688597b43 100644 (file)
--- a/arch/cris/arch-v10/boot/rescue/kimagerescue.S
+++ b/arch/cris/arch-v10/boot/rescue/kimagerescue.S
@@ -1,5 +1,4 @@
-/* $Id: kimagerescue.S,v 1.1 2001/12/17 13:59:27 bjornw Exp $
- * 
+/*
  * Rescue code to be prepended on a kimage and copied to the
  * rescue serial port.
  * This is called from the rescue code, it will copy received data to
@@ -7,13 +6,13 @@
  */
 
 #define ASSEMBLER_MACROS_ONLY
-#include <asm/sv_addr_ag.h>
+#include <asm/arch/sv_addr_ag.h>
 
 #define CODE_START 0x40004000
 #define CODE_LENGTH 784
 #define TIMEOUT_VALUE 1000
-       
-               
+
+
 #ifdef CONFIG_ETRAX_RESCUE_SER0
 #define SERXOFF R_SERIAL0_XOFF
 #define SERBAUD R_SERIAL0_BAUD
@@ -34,7 +33,7 @@
 #define SERRECC R_SERIAL2_REC_CTRL
 #define SERRDAT R_SERIAL2_REC_DATA
 #define SERSTAT R_SERIAL2_STATUS
-#endif 
+#endif
 #ifdef CONFIG_ETRAX_RESCUE_SER3
 #define SERXOFF R_SERIAL3_XOFF
 #define SERBAUD R_SERIAL3_BAUD
@@ -48,54 +47,55 @@
        ;; 0x80000000 if loaded in flash (as it should be)
        ;; since etrax actually starts at address 2 when booting from flash, we
        ;; put a nop (2 bytes) here first so we dont accidentally skip the di
-       
-       nop     
+
+       nop
        di
-#ifndef CONFIG_SVINTO_SIM      
+#ifndef CONFIG_SVINTO_SIM
        ;; setup port PA and PB default initial directions and data
        ;; (so we can flash LEDs, and so that DTR and others are set)
-       
+
        move.b  CONFIG_ETRAX_DEF_R_PORT_PA_DIR, $r0
        move.b  $r0, [R_PORT_PA_DIR]
        move.b  CONFIG_ETRAX_DEF_R_PORT_PA_DATA, $r0
        move.b  $r0, [R_PORT_PA_DATA]
-       
+
        move.b  CONFIG_ETRAX_DEF_R_PORT_PB_DIR, $r0
        move.b  $r0, [R_PORT_PB_DIR]
        move.b  CONFIG_ETRAX_DEF_R_PORT_PB_DATA, $r0
        move.b  $r0, [R_PORT_PB_DATA]
-       
+
        ;; We need to setup the bus registers before we start using the DRAM
 #include "../../lib/dram_init.S"
-       
+
 #endif
        ;; Setup the stack to a suitably high address.
        ;; We assume 8 MB is the minimum DRAM in an eLinux
        ;; product and put the sp at the top for now.
 
        move.d  0x40800000, $sp
-       
+
        ;; setup the serial port at 115200 baud
-       
+
        moveq   0, $r0
-       move.d  $r0, [SERXOFF] 
+       move.d  $r0, [SERXOFF]
 
        move.b  0x99, $r0
-       move.b  $r0, [SERBAUD]          ; 115.2kbaud for both transmit and receive
+       move.b  $r0, [SERBAUD]          ; 115.2kbaud for both transmit
+                                       ; and receive
 
        move.b  0x40, $r0               ; rec enable
-       move.b  $r0, [SERRECC] 
+       move.b  $r0, [SERRECC]
 
 
-       moveq   0, $r1          ; "timer" to clock out a LED red flash
-       move.d  CODE_START, $r3 ; destination counter
+       moveq   0, $r1                  ; "timer" to clock out a LED red flash
+       move.d  CODE_START, $r3         ; destination counter
        move.d  CODE_LENGTH, $r4        ; length
        move.d  TIMEOUT_VALUE, $r5      ; "timeout" until jump
 
 wait_ser:
        addq    1, $r1
-       subq    1, $r5          ; decrease timeout
-       beq     jump_start      ; timed out
+       subq    1, $r5                  ; decrease timeout
+       beq     jump_start              ; timed out
        nop
 #ifndef CONFIG_ETRAX_NO_LEDS
 #ifdef CONFIG_ETRAX_PA_LEDS
@@ -111,21 +111,21 @@ wait_ser:
        or.d    $r0, $r2                ; set bit
        ba      2f
        nop
-1:     not     $r0             ; clear bit
+1:     not     $r0                     ; clear bit
        and.d   $r0, $r2
-2:     
+2:
 #ifdef CONFIG_ETRAX_PA_LEDS
        move.b  $r2, [R_PORT_PA_DATA]
-#endif 
+#endif
 #ifdef CONFIG_ETRAX_PB_LEDS
        move.b  $r2, [R_PORT_PB_DATA]
 #endif
 #endif
-               
+
        ;; check if we got something on the serial port
-       
+
        move.b  [SERSTAT], $r0
-       btstq   0, $r0          ; data_avail
+       btstq   0, $r0                  ; data_avail
        bpl     wait_ser
        nop
 
@@ -134,7 +134,7 @@ wait_ser:
        move.b  [SERRDAT], $r0
        move.b  $r0, [$r3+]
        move.d  TIMEOUT_VALUE, $r5      ; reset "timeout"
-       subq    1, $r4          ; decrease length
+       subq    1, $r4                  ; decrease length
        bne     wait_ser
        nop
 jump_start: