W: http://www.baycom.org/~tom/ham/ham.html
S: Maintained
+B43 WIRELESS DRIVER
+P: Michael Buesch
+M: mb@bu3sch.de
+P: Stefano Brivio
+M: st3@riseup.net
+L: linux-wireless@vger.kernel.org
+W: http://bcm43xx.berlios.de/
+S: Maintained
+
BCM43XX WIRELESS DRIVER (SOFTMAC BASED VERSION)
P: Larry Finger
M: Larry.Finger@lwfinger.net
source "drivers/net/wireless/hostap/Kconfig"
source "drivers/net/wireless/bcm43xx/Kconfig"
+source "drivers/net/wireless/b43/Kconfig"
source "drivers/net/wireless/zd1211rw/Kconfig"
endmenu
obj-$(CONFIG_HOSTAP) += hostap/
obj-$(CONFIG_BCM43XX) += bcm43xx/
+obj-$(CONFIG_B43) += b43/
obj-$(CONFIG_ZD1211RW) += zd1211rw/
# 16-bit wireless PCMCIA client drivers
--- /dev/null
+config B43
+ tristate "Broadcom 43xx wireless support (mac80211 stack)"
+ depends on SSB_POSSIBLE && MAC80211 && WLAN_80211
+ select SSB
+ select FW_LOADER
+ select HW_RANDOM
+ ---help---
+ b43 is a driver for the Broadcom 43xx series wireless devices.
+
+ Check "lspci" for something like
+ "Broadcom Corporation BCM43XX 802.11 Wireless LAN Controller"
+ to determine whether you own such a device.
+
+ This driver supports the new BCM43xx IEEE 802.11G devices, but not
+ the old IEEE 802.11B devices. Old devices are supported by
+ the b43legacy driver.
+ Note that this has nothing to do with the standard that your AccessPoint
+ supports (A, B, G or a combination).
+ IEEE 802.11G devices can talk to IEEE 802.11B AccessPoints.
+
+ It is safe to include both b43 and b43legacy as the underlying glue
+ layer will automatically load the correct version for your device.
+
+ This driver uses V4 firmware, which must be installed separately using
+ b43-fwcutter.
+
+ This driver can be built as a module (recommended) that will be called "b43".
+ If unsure, say M.
+
+# Auto-select SSB PCI-HOST support, if possible
+config B43_PCI_AUTOSELECT
+ bool
+ depends on B43 && SSB_PCIHOST_POSSIBLE
+ select SSB_PCIHOST
+ default y
+
+# Auto-select SSB PCICORE driver, if possible
+config B43_PCICORE_AUTOSELECT
+ bool
+ depends on B43 && SSB_DRIVER_PCICORE_POSSIBLE
+ select SSB_DRIVER_PCICORE
+ default y
+
+config B43_PCMCIA
+ bool "Broadcom 43xx PCMCIA device support (EXPERIMENTAL)"
+ depends on B43 && SSB_PCMCIAHOST_POSSIBLE && EXPERIMENTAL
+ select SSB_PCMCIAHOST
+ ---help---
+ Broadcom 43xx PCMCIA device support.
+
+ Support for 16bit PCMCIA devices.
+ Please note that most PC-CARD devices are _NOT_ 16bit PCMCIA
+ devices, but 32bit CardBUS devices. CardBUS devices are supported
+ out of the box by b43.
+
+ With this config option you can drive b43 cards in
+ CompactFlash formfactor in a PCMCIA adaptor.
+ CF b43 cards can sometimes be found in handheld PCs.
+
+ It's safe to select Y here, even if you don't have a B43 PCMCIA device.
+
+ If unsure, say N.
+
+config B43_DEBUG
+ bool "Broadcom 43xx debugging"
+ depends on B43
+ ---help---
+ Broadcom 43xx debugging messages.
+
+ Say Y, if you want to find out why the driver does not
+ work for you.
+
+config B43_DMA
+ bool
+ depends on B43
+config B43_PIO
+ bool
+ depends on B43
+
+choice
+ prompt "Broadcom 43xx data transfer mode"
+ depends on B43
+ default B43_DMA_AND_PIO_MODE
+
+config B43_DMA_AND_PIO_MODE
+ bool "DMA + PIO"
+ select B43_DMA
+ select B43_PIO
+ ---help---
+ Include both, Direct Memory Access (DMA) and Programmed I/O (PIO)
+ data transfer modes.
+ The actually used mode is selectable through the module
+ parameter "pio". If the module parameter is pio=0, DMA is used.
+ Otherwise PIO is used. DMA is default.
+
+ If unsure, choose this option.
+
+config B43_DMA_MODE
+ bool "DMA (Direct Memory Access) only"
+ select B43_DMA
+ ---help---
+ Only include Direct Memory Access (DMA).
+ This reduces the size of the driver module, by omitting the PIO code.
+
+config B43_PIO_MODE
+ bool "PIO (Programmed I/O) only"
+ select B43_PIO
+ ---help---
+ Only include Programmed I/O (PIO).
+ This reduces the size of the driver module, by omitting the DMA code.
+ Please note that PIO transfers are slow (compared to DMA).
+
+ Also note that not all devices of the 43xx series support PIO.
+ The 4306 (Apple Airport Extreme and others) supports PIO, while
+ the 4318 is known to _not_ support PIO.
+
+ Only use PIO, if DMA does not work for you.
+
+endchoice
--- /dev/null
+# b43 core
+b43-y += main.o
+b43-y += tables.o
+b43-y += phy.o
+b43-y += sysfs.o
+b43-y += leds.o
+b43-y += xmit.o
+b43-y += lo.o
+# b43 PCMCIA support
+b43-$(CONFIG_B43_PCMCIA) += pcmcia.o
+# b43 debugging
+b43-$(CONFIG_B43_DEBUG) += debugfs.o
+# b43 DMA and PIO
+b43-$(CONFIG_B43_DMA) += dma.o
+b43-$(CONFIG_B43_PIO) += pio.o
+
+obj-$(CONFIG_B43) += b43.o
--- /dev/null
+#ifndef B43_H_
+#define B43_H_
+
+#include <linux/kernel.h>
+#include <linux/spinlock.h>
+#include <linux/interrupt.h>
+#include <linux/hw_random.h>
+#include <linux/ssb/ssb.h>
+#include <net/mac80211.h>
+
+#include "debugfs.h"
+#include "leds.h"
+#include "lo.h"
+#include "phy.h"
+
+#ifdef CONFIG_B43_DEBUG
+# define B43_DEBUG 1
+#else
+# define B43_DEBUG 0
+#endif
+
+#define B43_RX_MAX_SSI 60
+
+/* MMIO offsets */
+#define B43_MMIO_DMA0_REASON 0x20
+#define B43_MMIO_DMA0_IRQ_MASK 0x24
+#define B43_MMIO_DMA1_REASON 0x28
+#define B43_MMIO_DMA1_IRQ_MASK 0x2C
+#define B43_MMIO_DMA2_REASON 0x30
+#define B43_MMIO_DMA2_IRQ_MASK 0x34
+#define B43_MMIO_DMA3_REASON 0x38
+#define B43_MMIO_DMA3_IRQ_MASK 0x3C
+#define B43_MMIO_DMA4_REASON 0x40
+#define B43_MMIO_DMA4_IRQ_MASK 0x44
+#define B43_MMIO_DMA5_REASON 0x48
+#define B43_MMIO_DMA5_IRQ_MASK 0x4C
+#define B43_MMIO_MACCTL 0x120
+#define B43_MMIO_STATUS2_BITFIELD 0x124
+#define B43_MMIO_GEN_IRQ_REASON 0x128
+#define B43_MMIO_GEN_IRQ_MASK 0x12C
+#define B43_MMIO_RAM_CONTROL 0x130
+#define B43_MMIO_RAM_DATA 0x134
+#define B43_MMIO_PS_STATUS 0x140
+#define B43_MMIO_RADIO_HWENABLED_HI 0x158
+#define B43_MMIO_SHM_CONTROL 0x160
+#define B43_MMIO_SHM_DATA 0x164
+#define B43_MMIO_SHM_DATA_UNALIGNED 0x166
+#define B43_MMIO_XMITSTAT_0 0x170
+#define B43_MMIO_XMITSTAT_1 0x174
+#define B43_MMIO_REV3PLUS_TSF_LOW 0x180 /* core rev >= 3 only */
+#define B43_MMIO_REV3PLUS_TSF_HIGH 0x184 /* core rev >= 3 only */
+
+/* 32-bit DMA */
+#define B43_MMIO_DMA32_BASE0 0x200
+#define B43_MMIO_DMA32_BASE1 0x220
+#define B43_MMIO_DMA32_BASE2 0x240
+#define B43_MMIO_DMA32_BASE3 0x260
+#define B43_MMIO_DMA32_BASE4 0x280
+#define B43_MMIO_DMA32_BASE5 0x2A0
+/* 64-bit DMA */
+#define B43_MMIO_DMA64_BASE0 0x200
+#define B43_MMIO_DMA64_BASE1 0x240
+#define B43_MMIO_DMA64_BASE2 0x280
+#define B43_MMIO_DMA64_BASE3 0x2C0
+#define B43_MMIO_DMA64_BASE4 0x300
+#define B43_MMIO_DMA64_BASE5 0x340
+/* PIO */
+#define B43_MMIO_PIO1_BASE 0x300
+#define B43_MMIO_PIO2_BASE 0x310
+#define B43_MMIO_PIO3_BASE 0x320
+#define B43_MMIO_PIO4_BASE 0x330
+
+#define B43_MMIO_PHY_VER 0x3E0
+#define B43_MMIO_PHY_RADIO 0x3E2
+#define B43_MMIO_PHY0 0x3E6
+#define B43_MMIO_ANTENNA 0x3E8
+#define B43_MMIO_CHANNEL 0x3F0
+#define B43_MMIO_CHANNEL_EXT 0x3F4
+#define B43_MMIO_RADIO_CONTROL 0x3F6
+#define B43_MMIO_RADIO_DATA_HIGH 0x3F8
+#define B43_MMIO_RADIO_DATA_LOW 0x3FA
+#define B43_MMIO_PHY_CONTROL 0x3FC
+#define B43_MMIO_PHY_DATA 0x3FE
+#define B43_MMIO_MACFILTER_CONTROL 0x420
+#define B43_MMIO_MACFILTER_DATA 0x422
+#define B43_MMIO_RCMTA_COUNT 0x43C
+#define B43_MMIO_RADIO_HWENABLED_LO 0x49A
+#define B43_MMIO_GPIO_CONTROL 0x49C
+#define B43_MMIO_GPIO_MASK 0x49E
+#define B43_MMIO_TSF_0 0x632 /* core rev < 3 only */
+#define B43_MMIO_TSF_1 0x634 /* core rev < 3 only */
+#define B43_MMIO_TSF_2 0x636 /* core rev < 3 only */
+#define B43_MMIO_TSF_3 0x638 /* core rev < 3 only */
+#define B43_MMIO_RNG 0x65A
+#define B43_MMIO_POWERUP_DELAY 0x6A8
+
+/* SPROM boardflags_lo values */
+#define B43_BFL_BTCOEXIST 0x0001 /* implements Bluetooth coexistance */
+#define B43_BFL_PACTRL 0x0002 /* GPIO 9 controlling the PA */
+#define B43_BFL_AIRLINEMODE 0x0004 /* implements GPIO 13 radio disable indication */
+#define B43_BFL_RSSI 0x0008 /* software calculates nrssi slope. */
+#define B43_BFL_ENETSPI 0x0010 /* has ephy roboswitch spi */
+#define B43_BFL_XTAL_NOSLOW 0x0020 /* no slow clock available */
+#define B43_BFL_CCKHIPWR 0x0040 /* can do high power CCK transmission */
+#define B43_BFL_ENETADM 0x0080 /* has ADMtek switch */
+#define B43_BFL_ENETVLAN 0x0100 /* can do vlan */
+#define B43_BFL_AFTERBURNER 0x0200 /* supports Afterburner mode */
+#define B43_BFL_NOPCI 0x0400 /* leaves PCI floating */
+#define B43_BFL_FEM 0x0800 /* supports the Front End Module */
+#define B43_BFL_EXTLNA 0x1000 /* has an external LNA */
+#define B43_BFL_HGPA 0x2000 /* had high gain PA */
+#define B43_BFL_BTCMOD 0x4000 /* BFL_BTCOEXIST is given in alternate GPIOs */
+#define B43_BFL_ALTIQ 0x8000 /* alternate I/Q settings */
+
+/* GPIO register offset, in both ChipCommon and PCI core. */
+#define B43_GPIO_CONTROL 0x6c
+
+/* SHM Routing */
+enum {
+ B43_SHM_UCODE, /* Microcode memory */
+ B43_SHM_SHARED, /* Shared memory */
+ B43_SHM_SCRATCH, /* Scratch memory */
+ B43_SHM_HW, /* Internal hardware register */
+ B43_SHM_RCMTA, /* Receive match transmitter address (rev >= 5 only) */
+};
+/* SHM Routing modifiers */
+#define B43_SHM_AUTOINC_R 0x0200 /* Auto-increment address on read */
+#define B43_SHM_AUTOINC_W 0x0100 /* Auto-increment address on write */
+#define B43_SHM_AUTOINC_RW (B43_SHM_AUTOINC_R | \
+ B43_SHM_AUTOINC_W)
+
+/* Misc SHM_SHARED offsets */
+#define B43_SHM_SH_WLCOREREV 0x0016 /* 802.11 core revision */
+#define B43_SHM_SH_PCTLWDPOS 0x0008
+#define B43_SHM_SH_RXPADOFF 0x0034 /* RX Padding data offset (PIO only) */
+#define B43_SHM_SH_PHYVER 0x0050 /* PHY version */
+#define B43_SHM_SH_PHYTYPE 0x0052 /* PHY type */
+#define B43_SHM_SH_ANTSWAP 0x005C /* Antenna swap threshold */
+#define B43_SHM_SH_HOSTFLO 0x005E /* Hostflags for ucode options (low) */
+#define B43_SHM_SH_HOSTFHI 0x0060 /* Hostflags for ucode options (high) */
+#define B43_SHM_SH_RFATT 0x0064 /* Current radio attenuation value */
+#define B43_SHM_SH_RADAR 0x0066 /* Radar register */
+#define B43_SHM_SH_PHYTXNOI 0x006E /* PHY noise directly after TX (lower 8bit only) */
+#define B43_SHM_SH_RFRXSP1 0x0072 /* RF RX SP Register 1 */
+#define B43_SHM_SH_CHAN 0x00A0 /* Current channel (low 8bit only) */
+#define B43_SHM_SH_CHAN_5GHZ 0x0100 /* Bit set, if 5Ghz channel */
+#define B43_SHM_SH_BCMCFIFOID 0x0108 /* Last posted cookie to the bcast/mcast FIFO */
+/* SHM_SHARED TX FIFO variables */
+#define B43_SHM_SH_SIZE01 0x0098 /* TX FIFO size for FIFO 0 (low) and 1 (high) */
+#define B43_SHM_SH_SIZE23 0x009A /* TX FIFO size for FIFO 2 and 3 */
+#define B43_SHM_SH_SIZE45 0x009C /* TX FIFO size for FIFO 4 and 5 */
+#define B43_SHM_SH_SIZE67 0x009E /* TX FIFO size for FIFO 6 and 7 */
+/* SHM_SHARED background noise */
+#define B43_SHM_SH_JSSI0 0x0088 /* Measure JSSI 0 */
+#define B43_SHM_SH_JSSI1 0x008A /* Measure JSSI 1 */
+#define B43_SHM_SH_JSSIAUX 0x008C /* Measure JSSI AUX */
+/* SHM_SHARED crypto engine */
+#define B43_SHM_SH_DEFAULTIV 0x003C /* Default IV location */
+#define B43_SHM_SH_NRRXTRANS 0x003E /* # of soft RX transmitter addresses (max 8) */
+#define B43_SHM_SH_KTP 0x0056 /* Key table pointer */
+#define B43_SHM_SH_TKIPTSCTTAK 0x0318
+#define B43_SHM_SH_KEYIDXBLOCK 0x05D4 /* Key index/algorithm block (v4 firmware) */
+#define B43_SHM_SH_PSM 0x05F4 /* PSM transmitter address match block (rev < 5) */
+/* SHM_SHARED WME variables */
+#define B43_SHM_SH_EDCFSTAT 0x000E /* EDCF status */
+#define B43_SHM_SH_TXFCUR 0x0030 /* TXF current index */
+#define B43_SHM_SH_EDCFQ 0x0240 /* EDCF Q info */
+/* SHM_SHARED powersave mode related */
+#define B43_SHM_SH_SLOTT 0x0010 /* Slot time */
+#define B43_SHM_SH_DTIMPER 0x0012 /* DTIM period */
+#define B43_SHM_SH_NOSLPZNATDTIM 0x004C /* NOSLPZNAT DTIM */
+/* SHM_SHARED beacon variables */
+#define B43_SHM_SH_BTL0 0x0018 /* Beacon template length 0 */
+#define B43_SHM_SH_BTL1 0x001A /* Beacon template length 1 */
+#define B43_SHM_SH_BTSFOFF 0x001C /* Beacon TSF offset */
+#define B43_SHM_SH_TIMBPOS 0x001E /* TIM B position in beacon */
+#define B43_SHM_SH_SFFBLIM 0x0044 /* Short frame fallback retry limit */
+#define B43_SHM_SH_LFFBLIM 0x0046 /* Long frame fallback retry limit */
+#define B43_SHM_SH_BEACPHYCTL 0x0054 /* Beacon PHY TX control word (see PHY TX control) */
+/* SHM_SHARED ACK/CTS control */
+#define B43_SHM_SH_ACKCTSPHYCTL 0x0022 /* ACK/CTS PHY control word (see PHY TX control) */
+/* SHM_SHARED probe response variables */
+#define B43_SHM_SH_PRSSID 0x0160 /* Probe Response SSID */
+#define B43_SHM_SH_PRSSIDLEN 0x0048 /* Probe Response SSID length */
+#define B43_SHM_SH_PRTLEN 0x004A /* Probe Response template length */
+#define B43_SHM_SH_PRMAXTIME 0x0074 /* Probe Response max time */
+#define B43_SHM_SH_PRPHYCTL 0x0188 /* Probe Response PHY TX control word */
+/* SHM_SHARED rate tables */
+#define B43_SHM_SH_OFDMDIRECT 0x01C0 /* Pointer to OFDM direct map */
+#define B43_SHM_SH_OFDMBASIC 0x01E0 /* Pointer to OFDM basic rate map */
+#define B43_SHM_SH_CCKDIRECT 0x0200 /* Pointer to CCK direct map */
+#define B43_SHM_SH_CCKBASIC 0x0220 /* Pointer to CCK basic rate map */
+/* SHM_SHARED microcode soft registers */
+#define B43_SHM_SH_UCODEREV 0x0000 /* Microcode revision */
+#define B43_SHM_SH_UCODEPATCH 0x0002 /* Microcode patchlevel */
+#define B43_SHM_SH_UCODEDATE 0x0004 /* Microcode date */
+#define B43_SHM_SH_UCODETIME 0x0006 /* Microcode time */
+#define B43_SHM_SH_UCODESTAT 0x0040 /* Microcode debug status code */
+#define B43_SHM_SH_UCODESTAT_INVALID 0
+#define B43_SHM_SH_UCODESTAT_INIT 1
+#define B43_SHM_SH_UCODESTAT_ACTIVE 2
+#define B43_SHM_SH_UCODESTAT_SUSP 3 /* suspended */
+#define B43_SHM_SH_UCODESTAT_SLEEP 4 /* asleep (PS) */
+#define B43_SHM_SH_MAXBFRAMES 0x0080 /* Maximum number of frames in a burst */
+#define B43_SHM_SH_SPUWKUP 0x0094 /* pre-wakeup for synth PU in us */
+#define B43_SHM_SH_PRETBTT 0x0096 /* pre-TBTT in us */
+
+/* SHM_SCRATCH offsets */
+#define B43_SHM_SC_MINCONT 0x0003 /* Minimum contention window */
+#define B43_SHM_SC_MAXCONT 0x0004 /* Maximum contention window */
+#define B43_SHM_SC_CURCONT 0x0005 /* Current contention window */
+#define B43_SHM_SC_SRLIMIT 0x0006 /* Short retry count limit */
+#define B43_SHM_SC_LRLIMIT 0x0007 /* Long retry count limit */
+#define B43_SHM_SC_DTIMC 0x0008 /* Current DTIM count */
+#define B43_SHM_SC_BTL0LEN 0x0015 /* Beacon 0 template length */
+#define B43_SHM_SC_BTL1LEN 0x0016 /* Beacon 1 template length */
+#define B43_SHM_SC_SCFB 0x0017 /* Short frame transmit count threshold for rate fallback */
+#define B43_SHM_SC_LCFB 0x0018 /* Long frame transmit count threshold for rate fallback */
+
+/* Hardware Radio Enable masks */
+#define B43_MMIO_RADIO_HWENABLED_HI_MASK (1 << 16)
+#define B43_MMIO_RADIO_HWENABLED_LO_MASK (1 << 4)
+
+/* HostFlags. See b43_hf_read/write() */
+#define B43_HF_ANTDIVHELP 0x00000001 /* ucode antenna div helper */
+#define B43_HF_SYMW 0x00000002 /* G-PHY SYM workaround */
+#define B43_HF_RXPULLW 0x00000004 /* RX pullup workaround */
+#define B43_HF_CCKBOOST 0x00000008 /* 4dB CCK power boost (exclusive with OFDM boost) */
+#define B43_HF_BTCOEX 0x00000010 /* Bluetooth coexistance */
+#define B43_HF_GDCW 0x00000020 /* G-PHY DV canceller filter bw workaround */
+#define B43_HF_OFDMPABOOST 0x00000040 /* Enable PA gain boost for OFDM */
+#define B43_HF_ACPR 0x00000080 /* Disable for Japan, channel 14 */
+#define B43_HF_EDCF 0x00000100 /* on if WME and MAC suspended */
+#define B43_HF_TSSIRPSMW 0x00000200 /* TSSI reset PSM ucode workaround */
+#define B43_HF_DSCRQ 0x00000400 /* Disable slow clock request in ucode */
+#define B43_HF_ACIW 0x00000800 /* ACI workaround: shift bits by 2 on PHY CRS */
+#define B43_HF_2060W 0x00001000 /* 2060 radio workaround */
+#define B43_HF_RADARW 0x00002000 /* Radar workaround */
+#define B43_HF_USEDEFKEYS 0x00004000 /* Enable use of default keys */
+#define B43_HF_BT4PRIOCOEX 0x00010000 /* Bluetooth 2-priority coexistance */
+#define B43_HF_FWKUP 0x00020000 /* Fast wake-up ucode */
+#define B43_HF_VCORECALC 0x00040000 /* Force VCO recalculation when powering up synthpu */
+#define B43_HF_PCISCW 0x00080000 /* PCI slow clock workaround */
+#define B43_HF_4318TSSI 0x00200000 /* 4318 TSSI */
+#define B43_HF_FBCMCFIFO 0x00400000 /* Flush bcast/mcast FIFO immediately */
+#define B43_HF_HWPCTL 0x00800000 /* Enable hardwarre power control */
+#define B43_HF_BTCOEXALT 0x01000000 /* Bluetooth coexistance in alternate pins */
+#define B43_HF_TXBTCHECK 0x02000000 /* Bluetooth check during transmission */
+#define B43_HF_SKCFPUP 0x04000000 /* Skip CFP update */
+
+/* MacFilter offsets. */
+#define B43_MACFILTER_SELF 0x0000
+#define B43_MACFILTER_BSSID 0x0003
+
+/* PowerControl */
+#define B43_PCTL_IN 0xB0
+#define B43_PCTL_OUT 0xB4
+#define B43_PCTL_OUTENABLE 0xB8
+#define B43_PCTL_XTAL_POWERUP 0x40
+#define B43_PCTL_PLL_POWERDOWN 0x80
+
+/* PowerControl Clock Modes */
+#define B43_PCTL_CLK_FAST 0x00
+#define B43_PCTL_CLK_SLOW 0x01
+#define B43_PCTL_CLK_DYNAMIC 0x02
+
+#define B43_PCTL_FORCE_SLOW 0x0800
+#define B43_PCTL_FORCE_PLL 0x1000
+#define B43_PCTL_DYN_XTAL 0x2000
+
+/* PHYVersioning */
+#define B43_PHYTYPE_A 0x00
+#define B43_PHYTYPE_B 0x01
+#define B43_PHYTYPE_G 0x02
+
+/* PHYRegisters */
+#define B43_PHY_ILT_A_CTRL 0x0072
+#define B43_PHY_ILT_A_DATA1 0x0073
+#define B43_PHY_ILT_A_DATA2 0x0074
+#define B43_PHY_G_LO_CONTROL 0x0810
+#define B43_PHY_ILT_G_CTRL 0x0472
+#define B43_PHY_ILT_G_DATA1 0x0473
+#define B43_PHY_ILT_G_DATA2 0x0474
+#define B43_PHY_A_PCTL 0x007B
+#define B43_PHY_G_PCTL 0x0029
+#define B43_PHY_A_CRS 0x0029
+#define B43_PHY_RADIO_BITFIELD 0x0401
+#define B43_PHY_G_CRS 0x0429
+#define B43_PHY_NRSSILT_CTRL 0x0803
+#define B43_PHY_NRSSILT_DATA 0x0804
+
+/* RadioRegisters */
+#define B43_RADIOCTL_ID 0x01
+
+/* MAC Control bitfield */
+#define B43_MACCTL_ENABLED 0x00000001 /* MAC Enabled */
+#define B43_MACCTL_PSM_RUN 0x00000002 /* Run Microcode */
+#define B43_MACCTL_PSM_JMP0 0x00000004 /* Microcode jump to 0 */
+#define B43_MACCTL_SHM_ENABLED 0x00000100 /* SHM Enabled */
+#define B43_MACCTL_SHM_UPPER 0x00000200 /* SHM Upper */
+#define B43_MACCTL_IHR_ENABLED 0x00000400 /* IHR Region Enabled */
+#define B43_MACCTL_PSM_DBG 0x00002000 /* Microcode debugging enabled */
+#define B43_MACCTL_GPOUTSMSK 0x0000C000 /* GPOUT Select Mask */
+#define B43_MACCTL_BE 0x00010000 /* Big Endian mode */
+#define B43_MACCTL_INFRA 0x00020000 /* Infrastructure mode */
+#define B43_MACCTL_AP 0x00040000 /* AccessPoint mode */
+#define B43_MACCTL_RADIOLOCK 0x00080000 /* Radio lock */
+#define B43_MACCTL_BEACPROMISC 0x00100000 /* Beacon Promiscuous */
+#define B43_MACCTL_KEEP_BADPLCP 0x00200000 /* Keep frames with bad PLCP */
+#define B43_MACCTL_KEEP_CTL 0x00400000 /* Keep control frames */
+#define B43_MACCTL_KEEP_BAD 0x00800000 /* Keep bad frames (FCS) */
+#define B43_MACCTL_PROMISC 0x01000000 /* Promiscuous mode */
+#define B43_MACCTL_HWPS 0x02000000 /* Hardware Power Saving */
+#define B43_MACCTL_AWAKE 0x04000000 /* Device is awake */
+#define B43_MACCTL_CLOSEDNET 0x08000000 /* Closed net (no SSID bcast) */
+#define B43_MACCTL_TBTTHOLD 0x10000000 /* TBTT Hold */
+#define B43_MACCTL_DISCTXSTAT 0x20000000 /* Discard TX status */
+#define B43_MACCTL_DISCPMQ 0x40000000 /* Discard Power Management Queue */
+#define B43_MACCTL_GMODE 0x80000000 /* G Mode */
+
+/* 802.11 core specific TM State Low flags */
+#define B43_TMSLOW_GMODE 0x20000000 /* G Mode Enable */
+#define B43_TMSLOW_PLLREFSEL 0x00200000 /* PLL Frequency Reference Select */
+#define B43_TMSLOW_MACPHYCLKEN 0x00100000 /* MAC PHY Clock Control Enable (rev >= 5) */
+#define B43_TMSLOW_PHYRESET 0x00080000 /* PHY Reset */
+#define B43_TMSLOW_PHYCLKEN 0x00040000 /* PHY Clock Enable */
+
+/* 802.11 core specific TM State High flags */
+#define B43_TMSHIGH_FCLOCK 0x00040000 /* Fast Clock Available (rev >= 5) */
+#define B43_TMSHIGH_APHY 0x00020000 /* A-PHY available (rev >= 5) */
+#define B43_TMSHIGH_GPHY 0x00010000 /* G-PHY available (rev >= 5) */
+
+/* Generic-Interrupt reasons. */
+#define B43_IRQ_MAC_SUSPENDED 0x00000001
+#define B43_IRQ_BEACON 0x00000002
+#define B43_IRQ_TBTT_INDI 0x00000004
+#define B43_IRQ_BEACON_TX_OK 0x00000008
+#define B43_IRQ_BEACON_CANCEL 0x00000010
+#define B43_IRQ_ATIM_END 0x00000020
+#define B43_IRQ_PMQ 0x00000040
+#define B43_IRQ_PIO_WORKAROUND 0x00000100
+#define B43_IRQ_MAC_TXERR 0x00000200
+#define B43_IRQ_PHY_TXERR 0x00000800
+#define B43_IRQ_PMEVENT 0x00001000
+#define B43_IRQ_TIMER0 0x00002000
+#define B43_IRQ_TIMER1 0x00004000
+#define B43_IRQ_DMA 0x00008000
+#define B43_IRQ_TXFIFO_FLUSH_OK 0x00010000
+#define B43_IRQ_CCA_MEASURE_OK 0x00020000
+#define B43_IRQ_NOISESAMPLE_OK 0x00040000
+#define B43_IRQ_UCODE_DEBUG 0x08000000
+#define B43_IRQ_RFKILL 0x10000000
+#define B43_IRQ_TX_OK 0x20000000
+#define B43_IRQ_PHY_G_CHANGED 0x40000000
+#define B43_IRQ_TIMEOUT 0x80000000
+
+#define B43_IRQ_ALL 0xFFFFFFFF
+#define B43_IRQ_MASKTEMPLATE (B43_IRQ_MAC_SUSPENDED | \
+ B43_IRQ_BEACON | \
+ B43_IRQ_TBTT_INDI | \
+ B43_IRQ_ATIM_END | \
+ B43_IRQ_PMQ | \
+ B43_IRQ_MAC_TXERR | \
+ B43_IRQ_PHY_TXERR | \
+ B43_IRQ_DMA | \
+ B43_IRQ_TXFIFO_FLUSH_OK | \
+ B43_IRQ_NOISESAMPLE_OK | \
+ B43_IRQ_UCODE_DEBUG | \
+ B43_IRQ_RFKILL | \
+ B43_IRQ_TX_OK)
+
+/* Device specific rate values.
+ * The actual values defined here are (rate_in_mbps * 2).
+ * Some code depends on this. Don't change it. */
+#define B43_CCK_RATE_1MB 0x02
+#define B43_CCK_RATE_2MB 0x04
+#define B43_CCK_RATE_5MB 0x0B
+#define B43_CCK_RATE_11MB 0x16
+#define B43_OFDM_RATE_6MB 0x0C
+#define B43_OFDM_RATE_9MB 0x12
+#define B43_OFDM_RATE_12MB 0x18
+#define B43_OFDM_RATE_18MB 0x24
+#define B43_OFDM_RATE_24MB 0x30
+#define B43_OFDM_RATE_36MB 0x48
+#define B43_OFDM_RATE_48MB 0x60
+#define B43_OFDM_RATE_54MB 0x6C
+/* Convert a b43 rate value to a rate in 100kbps */
+#define B43_RATE_TO_BASE100KBPS(rate) (((rate) * 10) / 2)
+
+#define B43_DEFAULT_SHORT_RETRY_LIMIT 7
+#define B43_DEFAULT_LONG_RETRY_LIMIT 4
+
+/* Max size of a security key */
+#define B43_SEC_KEYSIZE 16
+/* Security algorithms. */
+enum {
+ B43_SEC_ALGO_NONE = 0, /* unencrypted, as of TX header. */
+ B43_SEC_ALGO_WEP40,
+ B43_SEC_ALGO_TKIP,
+ B43_SEC_ALGO_AES,
+ B43_SEC_ALGO_WEP104,
+ B43_SEC_ALGO_AES_LEGACY,
+};
+
+struct b43_dmaring;
+struct b43_pioqueue;
+
+/* The firmware file header */
+#define B43_FW_TYPE_UCODE 'u'
+#define B43_FW_TYPE_PCM 'p'
+#define B43_FW_TYPE_IV 'i'
+struct b43_fw_header {
+ /* File type */
+ u8 type;
+ /* File format version */
+ u8 ver;
+ u8 __padding[2];
+ /* Size of the data. For ucode and PCM this is in bytes.
+ * For IV this is number-of-ivs. */
+ __be32 size;
+} __attribute__((__packed__));
+
+/* Initial Value file format */
+#define B43_IV_OFFSET_MASK 0x7FFF
+#define B43_IV_32BIT 0x8000
+struct b43_iv {
+ __be16 offset_size;
+ union {
+ __be16 d16;
+ __be32 d32;
+ } data __attribute__((__packed__));
+} __attribute__((__packed__));
+
+
+#define B43_PHYMODE(phytype) (1 << (phytype))
+#define B43_PHYMODE_A B43_PHYMODE(B43_PHYTYPE_A)
+#define B43_PHYMODE_B B43_PHYMODE(B43_PHYTYPE_B)
+#define B43_PHYMODE_G B43_PHYMODE(B43_PHYTYPE_G)
+
+struct b43_phy {
+ /* Possible PHYMODEs on this PHY */
+ u8 possible_phymodes;
+ /* GMODE bit enabled? */
+ bool gmode;
+ /* Possible ieee80211 subsystem hwmodes for this PHY.
+ * Which mode is selected, depends on thr GMODE enabled bit */
+#define B43_MAX_PHYHWMODES 2
+ struct ieee80211_hw_mode hwmodes[B43_MAX_PHYHWMODES];
+
+ /* Analog Type */
+ u8 analog;
+ /* B43_PHYTYPE_ */
+ u8 type;
+ /* PHY revision number. */
+ u8 rev;
+
+ /* Radio versioning */
+ u16 radio_manuf; /* Radio manufacturer */
+ u16 radio_ver; /* Radio version */
+ u8 radio_rev; /* Radio revision */
+
+ bool radio_on; /* Radio switched on/off */
+ bool locked; /* Only used in b43_phy_{un}lock() */
+ bool dyn_tssi_tbl; /* tssi2dbm is kmalloc()ed. */
+
+ /* ACI (adjacent channel interference) flags. */
+ bool aci_enable;
+ bool aci_wlan_automatic;
+ bool aci_hw_rssi;
+
+ u16 minlowsig[2];
+ u16 minlowsigpos[2];
+
+ /* TSSI to dBm table in use */
+ const s8 *tssi2dbm;
+ /* Target idle TSSI */
+ int tgt_idle_tssi;
+ /* Current idle TSSI */
+ int cur_idle_tssi;
+
+ /* LocalOscillator control values. */
+ struct b43_txpower_lo_control *lo_control;
+ /* Values from b43_calc_loopback_gain() */
+ s16 max_lb_gain; /* Maximum Loopback gain in hdB */
+ s16 trsw_rx_gain; /* TRSW RX gain in hdB */
+ s16 lna_lod_gain; /* LNA lod */
+ s16 lna_gain; /* LNA */
+ s16 pga_gain; /* PGA */
+
+ /* PHY lock for core.rev < 3
+ * This lock is only used by b43_phy_{un}lock()
+ */
+ spinlock_t lock;
+
+ /* Desired TX power level (in dBm).
+ * This is set by the user and adjusted in b43_phy_xmitpower(). */
+ u8 power_level;
+ /* A-PHY TX Power control value. */
+ u16 txpwr_offset;
+
+ /* Current TX power level attenuation control values */
+ struct b43_bbatt bbatt;
+ struct b43_rfatt rfatt;
+ u8 tx_control; /* B43_TXCTL_XXX */
+#ifdef CONFIG_B43_DEBUG
+ bool manual_txpower_control; /* Manual TX-power control enabled? */
+#endif
+ /* Hardware Power Control enabled? */
+ bool hardware_power_control;
+
+ /* Current Interference Mitigation mode */
+ int interfmode;
+ /* Stack of saved values from the Interference Mitigation code.
+ * Each value in the stack is layed out as follows:
+ * bit 0-11: offset
+ * bit 12-15: register ID
+ * bit 16-32: value
+ * register ID is: 0x1 PHY, 0x2 Radio, 0x3 ILT
+ */
+#define B43_INTERFSTACK_SIZE 26
+ u32 interfstack[B43_INTERFSTACK_SIZE]; //FIXME: use a data structure
+
+ /* Saved values from the NRSSI Slope calculation */
+ s16 nrssi[2];
+ s32 nrssislope;
+ /* In memory nrssi lookup table. */
+ s8 nrssi_lt[64];
+
+ /* current channel */
+ u8 channel;
+
+ u16 lofcal;
+
+ u16 initval; //FIXME rename?
+};
+
+/* Data structures for DMA transmission, per 80211 core. */
+struct b43_dma {
+ struct b43_dmaring *tx_ring0;
+ struct b43_dmaring *tx_ring1;
+ struct b43_dmaring *tx_ring2;
+ struct b43_dmaring *tx_ring3;
+ struct b43_dmaring *tx_ring4;
+ struct b43_dmaring *tx_ring5;
+
+ struct b43_dmaring *rx_ring0;
+ struct b43_dmaring *rx_ring3; /* only available on core.rev < 5 */
+};
+
+/* Data structures for PIO transmission, per 80211 core. */
+struct b43_pio {
+ struct b43_pioqueue *queue0;
+ struct b43_pioqueue *queue1;
+ struct b43_pioqueue *queue2;
+ struct b43_pioqueue *queue3;
+};
+
+/* Context information for a noise calculation (Link Quality). */
+struct b43_noise_calculation {
+ u8 channel_at_start;
+ bool calculation_running;
+ u8 nr_samples;
+ s8 samples[8][4];
+};
+
+struct b43_stats {
+ u8 link_noise;
+ /* Store the last TX/RX times here for updating the leds. */
+ unsigned long last_tx;
+ unsigned long last_rx;
+};
+
+struct b43_key {
+ /* If keyconf is NULL, this key is disabled.
+ * keyconf is a cookie. Don't derefenrence it outside of the set_key
+ * path, because b43 doesn't own it. */
+ struct ieee80211_key_conf *keyconf;
+ u8 algorithm;
+};
+
+struct b43_wldev;
+
+/* Data structure for the WLAN parts (802.11 cores) of the b43 chip. */
+struct b43_wl {
+ /* Pointer to the active wireless device on this chip */
+ struct b43_wldev *current_dev;
+ /* Pointer to the ieee80211 hardware data structure */
+ struct ieee80211_hw *hw;
+
+ spinlock_t irq_lock;
+ struct mutex mutex;
+ spinlock_t leds_lock;
+
+ /* We can only have one operating interface (802.11 core)
+ * at a time. General information about this interface follows.
+ */
+
+ /* Opaque ID of the operating interface (!= monitor
+ * interface) from the ieee80211 subsystem.
+ * Do not modify.
+ */
+ int if_id;
+ /* The MAC address of the operating interface. */
+ u8 mac_addr[ETH_ALEN];
+ /* Current BSSID */
+ u8 bssid[ETH_ALEN];
+ /* Interface type. (IEEE80211_IF_TYPE_XXX) */
+ int if_type;
+ /* Counter of active monitor interfaces. */
+ int monitor;
+ /* Is the card operating in AP, STA or IBSS mode? */
+ bool operating;
+ /* Promisc mode active?
+ * Note that (monitor != 0) implies promisc.
+ */
+ bool promisc;
+ /* Stats about the wireless interface */
+ struct ieee80211_low_level_stats ieee_stats;
+
+ struct hwrng rng;
+ u8 rng_initialized;
+ char rng_name[30 + 1];
+
+ /* List of all wireless devices on this chip */
+ struct list_head devlist;
+ u8 nr_devs;
+};
+
+/* Pointers to the firmware data and meta information about it. */
+struct b43_firmware {
+ /* Microcode */
+ const struct firmware *ucode;
+ /* PCM code */
+ const struct firmware *pcm;
+ /* Initial MMIO values for the firmware */
+ const struct firmware *initvals;
+ /* Initial MMIO values for the firmware, band-specific */
+ const struct firmware *initvals_band;
+ /* Firmware revision */
+ u16 rev;
+ /* Firmware patchlevel */
+ u16 patch;
+};
+
+/* Device (802.11 core) initialization status. */
+enum {
+ B43_STAT_UNINIT = 0, /* Uninitialized. */
+ B43_STAT_INITIALIZED = 1, /* Initialized, but not started, yet. */
+ B43_STAT_STARTED = 2, /* Up and running. */
+};
+#define b43_status(wldev) atomic_read(&(wldev)->__init_status)
+#define b43_set_status(wldev, stat) do { \
+ atomic_set(&(wldev)->__init_status, (stat)); \
+ smp_wmb(); \
+ } while (0)
+
+/* XXX--- HOW LOCKING WORKS IN B43 ---XXX
+ *
+ * You should always acquire both, wl->mutex and wl->irq_lock unless:
+ * - You don't need to acquire wl->irq_lock, if the interface is stopped.
+ * - You don't need to acquire wl->mutex in the IRQ handler, IRQ tasklet
+ * and packet TX path (and _ONLY_ there.)
+ */
+
+/* Data structure for one wireless device (802.11 core) */
+struct b43_wldev {
+ struct ssb_device *dev;
+ struct b43_wl *wl;
+
+ /* The device initialization status.
+ * Use b43_status() to query. */
+ atomic_t __init_status;
+ /* Saved init status for handling suspend. */
+ int suspend_init_status;
+
+ bool __using_pio; /* Internal, use b43_using_pio(). */
+ bool bad_frames_preempt; /* Use "Bad Frames Preemption" (default off) */
+ bool reg124_set_0x4; /* Some variable to keep track of IRQ stuff. */
+ bool short_preamble; /* TRUE, if short preamble is enabled. */
+ bool short_slot; /* TRUE, if short slot timing is enabled. */
+ bool radio_hw_enable; /* saved state of radio hardware enabled state */
+
+ /* PHY/Radio device. */
+ struct b43_phy phy;
+ union {
+ /* DMA engines. */
+ struct b43_dma dma;
+ /* PIO engines. */
+ struct b43_pio pio;
+ };
+
+ /* Various statistics about the physical device. */
+ struct b43_stats stats;
+
+#define B43_NR_LEDS 4
+ struct b43_led leds[B43_NR_LEDS];
+
+ /* Reason code of the last interrupt. */
+ u32 irq_reason;
+ u32 dma_reason[6];
+ /* saved irq enable/disable state bitfield. */
+ u32 irq_savedstate;
+ /* Link Quality calculation context. */
+ struct b43_noise_calculation noisecalc;
+ /* if > 0 MAC is suspended. if == 0 MAC is enabled. */
+ int mac_suspended;
+
+ /* Interrupt Service Routine tasklet (bottom-half) */
+ struct tasklet_struct isr_tasklet;
+
+ /* Periodic tasks */
+ struct delayed_work periodic_work;
+ unsigned int periodic_state;
+
+ struct work_struct restart_work;
+
+ /* encryption/decryption */
+ u16 ktp; /* Key table pointer */
+ u8 max_nr_keys;
+ struct b43_key key[58];
+
+ /* Cached beacon template while uploading the template. */
+ struct sk_buff *cached_beacon;
+
+ /* Firmware data */
+ struct b43_firmware fw;
+
+ /* Devicelist in struct b43_wl (all 802.11 cores) */
+ struct list_head list;
+
+ /* Debugging stuff follows. */
+#ifdef CONFIG_B43_DEBUG
+ struct b43_dfsentry *dfsentry;
+#endif
+};
+
+static inline struct b43_wl *hw_to_b43_wl(struct ieee80211_hw *hw)
+{
+ return hw->priv;
+}
+
+/* Helper function, which returns a boolean.
+ * TRUE, if PIO is used; FALSE, if DMA is used.
+ */
+#if defined(CONFIG_B43_DMA) && defined(CONFIG_B43_PIO)
+static inline int b43_using_pio(struct b43_wldev *dev)
+{
+ return dev->__using_pio;
+}
+#elif defined(CONFIG_B43_DMA)
+static inline int b43_using_pio(struct b43_wldev *dev)
+{
+ return 0;
+}
+#elif defined(CONFIG_B43_PIO)
+static inline int b43_using_pio(struct b43_wldev *dev)
+{
+ return 1;
+}
+#else
+# error "Using neither DMA nor PIO? Confused..."
+#endif
+
+static inline struct b43_wldev *dev_to_b43_wldev(struct device *dev)
+{
+ struct ssb_device *ssb_dev = dev_to_ssb_dev(dev);
+ return ssb_get_drvdata(ssb_dev);
+}
+
+/* Is the device operating in a specified mode (IEEE80211_IF_TYPE_XXX). */
+static inline int b43_is_mode(struct b43_wl *wl, int type)
+{
+ if (type == IEEE80211_IF_TYPE_MNTR)
+ return !!(wl->monitor);
+ return (wl->operating && wl->if_type == type);
+}
+
+static inline u16 b43_read16(struct b43_wldev *dev, u16 offset)
+{
+ return ssb_read16(dev->dev, offset);
+}
+
+static inline void b43_write16(struct b43_wldev *dev, u16 offset, u16 value)
+{
+ ssb_write16(dev->dev, offset, value);
+}
+
+static inline u32 b43_read32(struct b43_wldev *dev, u16 offset)
+{
+ return ssb_read32(dev->dev, offset);
+}
+
+static inline void b43_write32(struct b43_wldev *dev, u16 offset, u32 value)
+{
+ ssb_write32(dev->dev, offset, value);
+}
+
+/* Message printing */
+void b43info(struct b43_wl *wl, const char *fmt, ...)
+ __attribute__ ((format(printf, 2, 3)));
+void b43err(struct b43_wl *wl, const char *fmt, ...)
+ __attribute__ ((format(printf, 2, 3)));
+void b43warn(struct b43_wl *wl, const char *fmt, ...)
+ __attribute__ ((format(printf, 2, 3)));
+#if B43_DEBUG
+void b43dbg(struct b43_wl *wl, const char *fmt, ...)
+ __attribute__ ((format(printf, 2, 3)));
+#else /* DEBUG */
+# define b43dbg(wl, fmt...) do { /* nothing */ } while (0)
+#endif /* DEBUG */
+
+/* A WARN_ON variant that vanishes when b43 debugging is disabled.
+ * This _also_ evaluates the arg with debugging disabled. */
+#if B43_DEBUG
+# define B43_WARN_ON(x) WARN_ON(x)
+#else
+static inline bool __b43_warn_on_dummy(bool x) { return x; }
+# define B43_WARN_ON(x) __b43_warn_on_dummy(unlikely(!!(x)))
+#endif
+
+/** Limit a value between two limits */
+#ifdef limit_value
+# undef limit_value
+#endif
+#define limit_value(value, min, max) \
+ ({ \
+ typeof(value) __value = (value); \
+ typeof(value) __min = (min); \
+ typeof(value) __max = (max); \
+ if (__value < __min) \
+ __value = __min; \
+ else if (__value > __max) \
+ __value = __max; \
+ __value; \
+ })
+
+/* Convert an integer to a Q5.2 value */
+#define INT_TO_Q52(i) ((i) << 2)
+/* Convert a Q5.2 value to an integer (precision loss!) */
+#define Q52_TO_INT(q52) ((q52) >> 2)
+/* Macros for printing a value in Q5.2 format */
+#define Q52_FMT "%u.%u"
+#define Q52_ARG(q52) Q52_TO_INT(q52), ((((q52) & 0x3) * 100) / 4)
+
+#endif /* B43_H_ */
--- /dev/null
+/*
+
+ Broadcom B43 wireless driver
+
+ debugfs driver debugging code
+
+ Copyright (c) 2005-2007 Michael Buesch <mb@bu3sch.de>
+
+ This program is free software; you can redistribute it and/or modify
+ it under the terms of the GNU General Public License as published by
+ the Free Software Foundation; either version 2 of the License, or
+ (at your option) any later version.
+
+ This program is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ GNU General Public License for more details.
+
+ You should have received a copy of the GNU General Public License
+ along with this program; see the file COPYING. If not, write to
+ the Free Software Foundation, Inc., 51 Franklin Steet, Fifth Floor,
+ Boston, MA 02110-1301, USA.
+
+*/
+
+#include <linux/fs.h>
+#include <linux/debugfs.h>
+#include <linux/slab.h>
+#include <linux/netdevice.h>
+#include <linux/pci.h>
+#include <linux/mutex.h>
+
+#include "b43.h"
+#include "main.h"
+#include "debugfs.h"
+#include "dma.h"
+#include "pio.h"
+#include "xmit.h"
+
+
+/* The root directory. */
+struct dentry *rootdir;
+
+struct b43_debugfs_fops {
+ ssize_t (*read)(struct b43_wldev *dev, char *buf, size_t bufsize);
+ int (*write)(struct b43_wldev *dev, const char *buf, size_t count);
+ struct file_operations fops;
+ /* Offset of struct b43_dfs_file in struct b43_dfsentry */
+ size_t file_struct_offset;
+ /* Take wl->irq_lock before calling read/write? */
+ bool take_irqlock;
+};
+
+static inline
+struct b43_dfs_file * fops_to_dfs_file(struct b43_wldev *dev,
+ const struct b43_debugfs_fops *dfops)
+{
+ void *p;
+
+ p = dev->dfsentry;
+ p += dfops->file_struct_offset;
+
+ return p;
+}
+
+
+#define fappend(fmt, x...) \
+ do { \
+ if (bufsize - count) \
+ count += snprintf(buf + count, \
+ bufsize - count, \
+ fmt , ##x); \
+ else \
+ printk(KERN_ERR "b43: fappend overflow\n"); \
+ } while (0)
+
+
+/* wl->irq_lock is locked */
+ssize_t tsf_read_file(struct b43_wldev *dev, char *buf, size_t bufsize)
+{
+ ssize_t count = 0;
+ u64 tsf;
+
+ b43_tsf_read(dev, &tsf);
+ fappend("0x%08x%08x\n",
+ (unsigned int)((tsf & 0xFFFFFFFF00000000ULL) >> 32),
+ (unsigned int)(tsf & 0xFFFFFFFFULL));
+
+ return count;
+}
+
+/* wl->irq_lock is locked */
+int tsf_write_file(struct b43_wldev *dev, const char *buf, size_t count)
+{
+ u64 tsf;
+
+ if (sscanf(buf, "%llu", (unsigned long long *)(&tsf)) != 1)
+ return -EINVAL;
+ b43_tsf_write(dev, tsf);
+
+ return 0;
+}
+
+/* wl->irq_lock is locked */
+ssize_t ucode_regs_read_file(struct b43_wldev *dev, char *buf, size_t bufsize)
+{
+ ssize_t count = 0;
+ int i;
+
+ for (i = 0; i < 64; i++) {
+ fappend("r%d = 0x%04x\n", i,
+ b43_shm_read16(dev, B43_SHM_SCRATCH, i));
+ }
+
+ return count;
+}
+
+/* wl->irq_lock is locked */
+ssize_t shm_read_file(struct b43_wldev *dev, char *buf, size_t bufsize)
+{
+ ssize_t count = 0;
+ int i;
+ u16 tmp;
+ __le16 *le16buf = (__le16 *)buf;
+
+ for (i = 0; i < 0x1000; i++) {
+ if (bufsize <= 0)
+ break;
+ tmp = b43_shm_read16(dev, B43_SHM_SHARED, 2 * i);
+ le16buf[i] = cpu_to_le16(tmp);
+ count += sizeof(tmp);
+ bufsize -= sizeof(tmp);
+ }
+
+ return count;
+}
+
+ssize_t txstat_read_file(struct b43_wldev *dev, char *buf, size_t bufsize)
+{
+ struct b43_txstatus_log *log = &dev->dfsentry->txstatlog;
+ ssize_t count = 0;
+ unsigned long flags;
+ int i, idx;
+ struct b43_txstatus *stat;
+
+ spin_lock_irqsave(&log->lock, flags);
+ if (log->end < 0) {
+ fappend("Nothing transmitted, yet\n");
+ goto out_unlock;
+ }
+ fappend("b43 TX status reports:\n\n"
+ "index | cookie | seq | phy_stat | frame_count | "
+ "rts_count | supp_reason | pm_indicated | "
+ "intermediate | for_ampdu | acked\n" "---\n");
+ i = log->end + 1;
+ idx = 0;
+ while (1) {
+ if (i == B43_NR_LOGGED_TXSTATUS)
+ i = 0;
+ stat = &(log->log[i]);
+ if (stat->cookie) {
+ fappend("%03d | "
+ "0x%04X | 0x%04X | 0x%02X | "
+ "0x%X | 0x%X | "
+ "%u | %u | "
+ "%u | %u | %u\n",
+ idx,
+ stat->cookie, stat->seq, stat->phy_stat,
+ stat->frame_count, stat->rts_count,
+ stat->supp_reason, stat->pm_indicated,
+ stat->intermediate, stat->for_ampdu,
+ stat->acked);
+ idx++;
+ }
+ if (i == log->end)
+ break;
+ i++;
+ }
+out_unlock:
+ spin_unlock_irqrestore(&log->lock, flags);
+
+ return count;
+}
+
+ssize_t txpower_g_read_file(struct b43_wldev *dev, char *buf, size_t bufsize)
+{
+ ssize_t count = 0;
+
+ if (dev->phy.type != B43_PHYTYPE_G) {
+ fappend("Device is not a G-PHY\n");
+ goto out;
+ }
+ fappend("Control: %s\n", dev->phy.manual_txpower_control ?
+ "MANUAL" : "AUTOMATIC");
+ fappend("Baseband attenuation: %u\n", dev->phy.bbatt.att);
+ fappend("Radio attenuation: %u\n", dev->phy.rfatt.att);
+ fappend("TX Mixer Gain: %s\n",
+ (dev->phy.tx_control & B43_TXCTL_TXMIX) ? "ON" : "OFF");
+ fappend("PA Gain 2dB: %s\n",
+ (dev->phy.tx_control & B43_TXCTL_PA2DB) ? "ON" : "OFF");
+ fappend("PA Gain 3dB: %s\n",
+ (dev->phy.tx_control & B43_TXCTL_PA3DB) ? "ON" : "OFF");
+ fappend("\n\n");
+ fappend("You can write to this file:\n");
+ fappend("Writing \"auto\" enables automatic txpower control.\n");
+ fappend
+ ("Writing the attenuation values as \"bbatt rfatt txmix pa2db pa3db\" "
+ "enables manual txpower control.\n");
+ fappend("Example: 5 4 0 0 1\n");
+ fappend("Enables manual control with Baseband attenuation 5, "
+ "Radio attenuation 4, No TX Mixer Gain, "
+ "No PA Gain 2dB, With PA Gain 3dB.\n");
+out:
+ return count;
+}
+
+int txpower_g_write_file(struct b43_wldev *dev, const char *buf, size_t count)
+{
+ unsigned long flags;
+ unsigned long phy_flags;
+ int err = 0;
+
+ spin_lock_irqsave(&dev->wl->irq_lock, flags);
+ if (dev->phy.type != B43_PHYTYPE_G) {
+ err = -ENODEV;
+ goto out_unlock;
+ }
+ if ((count >= 4) && (memcmp(buf, "auto", 4) == 0)) {
+ /* Automatic control */
+ dev->phy.manual_txpower_control = 0;
+ b43_phy_xmitpower(dev);
+ } else {
+ int bbatt = 0, rfatt = 0, txmix = 0, pa2db = 0, pa3db = 0;
+ /* Manual control */
+ if (sscanf(buf, "%d %d %d %d %d", &bbatt, &rfatt,
+ &txmix, &pa2db, &pa3db) != 5) {
+ err = -EINVAL;
+ goto out_unlock;
+ }
+ b43_put_attenuation_into_ranges(dev, &bbatt, &rfatt);
+ dev->phy.manual_txpower_control = 1;
+ dev->phy.bbatt.att = bbatt;
+ dev->phy.rfatt.att = rfatt;
+ dev->phy.tx_control = 0;
+ if (txmix)
+ dev->phy.tx_control |= B43_TXCTL_TXMIX;
+ if (pa2db)
+ dev->phy.tx_control |= B43_TXCTL_PA2DB;
+ if (pa3db)
+ dev->phy.tx_control |= B43_TXCTL_PA3DB;
+ b43_phy_lock(dev, phy_flags);
+ b43_radio_lock(dev);
+ b43_set_txpower_g(dev, &dev->phy.bbatt,
+ &dev->phy.rfatt, dev->phy.tx_control);
+ b43_radio_unlock(dev);
+ b43_phy_unlock(dev, phy_flags);
+ }
+out_unlock:
+ spin_unlock_irqrestore(&dev->wl->irq_lock, flags);
+
+ return err;
+}
+
+/* wl->irq_lock is locked */
+int restart_write_file(struct b43_wldev *dev, const char *buf, size_t count)
+{
+ int err = 0;
+
+ if (count > 0 && buf[0] == '1') {
+ b43_controller_restart(dev, "manually restarted");
+ } else
+ err = -EINVAL;
+
+ return err;
+}
+
+static ssize_t append_lo_table(ssize_t count, char *buf, const size_t bufsize,
+ struct b43_loctl table[B43_NR_BB][B43_NR_RF])
+{
+ unsigned int i, j;
+ struct b43_loctl *ctl;
+
+ for (i = 0; i < B43_NR_BB; i++) {
+ for (j = 0; j < B43_NR_RF; j++) {
+ ctl = &(table[i][j]);
+ fappend("(bbatt %2u, rfatt %2u) -> "
+ "(I %+3d, Q %+3d, Used: %d, Calibrated: %d)\n",
+ i, j, ctl->i, ctl->q,
+ ctl->used,
+ b43_loctl_is_calibrated(ctl));
+ }
+ }
+
+ return count;
+}
+
+ssize_t loctls_read_file(struct b43_wldev *dev, char *buf, size_t bufsize)
+{
+ ssize_t count = 0;
+ struct b43_txpower_lo_control *lo;
+ int i, err = 0;
+
+ if (dev->phy.type != B43_PHYTYPE_G) {
+ fappend("Device is not a G-PHY\n");
+ err = -ENODEV;
+ goto out;
+ }
+ lo = dev->phy.lo_control;
+ fappend("-- Local Oscillator calibration data --\n\n");
+ fappend("Measured: %d, Rebuild: %d, HW-power-control: %d\n",
+ lo->lo_measured,
+ lo->rebuild,
+ dev->phy.hardware_power_control);
+ fappend("TX Bias: 0x%02X, TX Magn: 0x%02X\n",
+ lo->tx_bias, lo->tx_magn);
+ fappend("Power Vector: 0x%08X%08X\n",
+ (unsigned int)((lo->power_vector & 0xFFFFFFFF00000000ULL) >> 32),
+ (unsigned int)(lo->power_vector & 0x00000000FFFFFFFFULL));
+ fappend("\nControl table WITH PADMIX:\n");
+ count = append_lo_table(count, buf, bufsize, lo->with_padmix);
+ fappend("\nControl table WITHOUT PADMIX:\n");
+ count = append_lo_table(count, buf, bufsize, lo->no_padmix);
+ fappend("\nUsed RF attenuation values: Value(WithPadmix flag)\n");
+ for (i = 0; i < lo->rfatt_list.len; i++) {
+ fappend("%u(%d), ",
+ lo->rfatt_list.list[i].att,
+ lo->rfatt_list.list[i].with_padmix);
+ }
+ fappend("\n");
+ fappend("\nUsed Baseband attenuation values:\n");
+ for (i = 0; i < lo->bbatt_list.len; i++) {
+ fappend("%u, ",
+ lo->bbatt_list.list[i].att);
+ }
+ fappend("\n");
+
+out:
+ return err ? err : count;
+}
+
+#undef fappend
+
+static int b43_debugfs_open(struct inode *inode, struct file *file)
+{
+ file->private_data = inode->i_private;
+ return 0;
+}
+
+static ssize_t b43_debugfs_read(struct file *file, char __user *userbuf,
+ size_t count, loff_t *ppos)
+{
+ struct b43_wldev *dev;
+ struct b43_debugfs_fops *dfops;
+ struct b43_dfs_file *dfile;
+ ssize_t ret;
+ char *buf;
+ const size_t bufsize = 1024 * 128;
+ const size_t buforder = get_order(bufsize);
+ int err = 0;
+
+ if (!count)
+ return 0;
+ dev = file->private_data;
+ if (!dev)
+ return -ENODEV;
+
+ mutex_lock(&dev->wl->mutex);
+ if (b43_status(dev) < B43_STAT_INITIALIZED) {
+ err = -ENODEV;
+ goto out_unlock;
+ }
+
+ dfops = container_of(file->f_op, struct b43_debugfs_fops, fops);
+ if (!dfops->read) {
+ err = -ENOSYS;
+ goto out_unlock;
+ }
+ dfile = fops_to_dfs_file(dev, dfops);
+
+ if (!dfile->buffer) {
+ buf = (char *)__get_free_pages(GFP_KERNEL, buforder);
+ if (!buf) {
+ err = -ENOMEM;
+ goto out_unlock;
+ }
+ memset(buf, 0, bufsize);
+ if (dfops->take_irqlock) {
+ spin_lock_irq(&dev->wl->irq_lock);
+ ret = dfops->read(dev, buf, bufsize);
+ spin_unlock_irq(&dev->wl->irq_lock);
+ } else
+ ret = dfops->read(dev, buf, bufsize);
+ if (ret <= 0) {
+ free_pages((unsigned long)buf, buforder);
+ err = ret;
+ goto out_unlock;
+ }
+ dfile->data_len = ret;
+ dfile->buffer = buf;
+ }
+
+ ret = simple_read_from_buffer(userbuf, count, ppos,
+ dfile->buffer,
+ dfile->data_len);
+ if (*ppos >= dfile->data_len) {
+ free_pages((unsigned long)dfile->buffer, buforder);
+ dfile->buffer = NULL;
+ dfile->data_len = 0;
+ }
+out_unlock:
+ mutex_unlock(&dev->wl->mutex);
+
+ return err ? err : ret;
+}
+
+static ssize_t b43_debugfs_write(struct file *file,
+ const char __user *userbuf,
+ size_t count, loff_t *ppos)
+{
+ struct b43_wldev *dev;
+ struct b43_debugfs_fops *dfops;
+ char *buf;
+ int err = 0;
+
+ if (!count)
+ return 0;
+ if (count > PAGE_SIZE)
+ return -E2BIG;
+ dev = file->private_data;
+ if (!dev)
+ return -ENODEV;
+
+ mutex_lock(&dev->wl->mutex);
+ if (b43_status(dev) < B43_STAT_INITIALIZED) {
+ err = -ENODEV;
+ goto out_unlock;
+ }
+
+ dfops = container_of(file->f_op, struct b43_debugfs_fops, fops);
+ if (!dfops->write) {
+ err = -ENOSYS;
+ goto out_unlock;
+ }
+
+ buf = (char *)get_zeroed_page(GFP_KERNEL);
+ if (!buf) {
+ err = -ENOMEM;
+ goto out_unlock;
+ }
+ if (copy_from_user(buf, userbuf, count)) {
+ err = -EFAULT;
+ goto out_freepage;
+ }
+ if (dfops->take_irqlock) {
+ spin_lock_irq(&dev->wl->irq_lock);
+ err = dfops->write(dev, buf, count);
+ spin_unlock_irq(&dev->wl->irq_lock);
+ } else
+ err = dfops->write(dev, buf, count);
+ if (err)
+ goto out_freepage;
+
+out_freepage:
+ free_page((unsigned long)buf);
+out_unlock:
+ mutex_unlock(&dev->wl->mutex);
+
+ return err ? err : count;
+}
+
+
+#define B43_DEBUGFS_FOPS(name, _read, _write, _take_irqlock) \
+ static struct b43_debugfs_fops fops_##name = { \
+ .read = _read, \
+ .write = _write, \
+ .fops = { \
+ .open = b43_debugfs_open, \
+ .read = b43_debugfs_read, \
+ .write = b43_debugfs_write, \
+ }, \
+ .file_struct_offset = offsetof(struct b43_dfsentry, \
+ file_##name), \
+ .take_irqlock = _take_irqlock, \
+ }
+
+B43_DEBUGFS_FOPS(tsf, tsf_read_file, tsf_write_file, 1);
+B43_DEBUGFS_FOPS(ucode_regs, ucode_regs_read_file, NULL, 1);
+B43_DEBUGFS_FOPS(shm, shm_read_file, NULL, 1);
+B43_DEBUGFS_FOPS(txstat, txstat_read_file, NULL, 0);
+B43_DEBUGFS_FOPS(txpower_g, txpower_g_read_file, txpower_g_write_file, 0);
+B43_DEBUGFS_FOPS(restart, NULL, restart_write_file, 1);
+B43_DEBUGFS_FOPS(loctls, loctls_read_file, NULL, 0);
+
+
+int b43_debug(struct b43_wldev *dev, enum b43_dyndbg feature)
+{
+ return !!(dev->dfsentry && dev->dfsentry->dyn_debug[feature]);
+}
+
+static void b43_remove_dynamic_debug(struct b43_wldev *dev)
+{
+ struct b43_dfsentry *e = dev->dfsentry;
+ int i;
+
+ for (i = 0; i < __B43_NR_DYNDBG; i++)
+ debugfs_remove(e->dyn_debug_dentries[i]);
+}
+
+static void b43_add_dynamic_debug(struct b43_wldev *dev)
+{
+ struct b43_dfsentry *e = dev->dfsentry;
+ struct dentry *d;
+
+#define add_dyn_dbg(name, id, initstate) do { \
+ e->dyn_debug[id] = (initstate); \
+ d = debugfs_create_bool(name, 0600, e->subdir, \
+ &(e->dyn_debug[id])); \
+ if (!IS_ERR(d)) \
+ e->dyn_debug_dentries[id] = d; \
+ } while (0)
+
+ add_dyn_dbg("debug_xmitpower", B43_DBG_XMITPOWER, 0);
+ add_dyn_dbg("debug_dmaoverflow", B43_DBG_DMAOVERFLOW, 0);
+ add_dyn_dbg("debug_dmaverbose", B43_DBG_DMAVERBOSE, 0);
+ add_dyn_dbg("debug_pwork_fast", B43_DBG_PWORK_FAST, 0);
+ add_dyn_dbg("debug_pwork_stop", B43_DBG_PWORK_STOP, 0);
+
+#undef add_dyn_dbg
+}
+
+void b43_debugfs_add_device(struct b43_wldev *dev)
+{
+ struct b43_dfsentry *e;
+ struct b43_txstatus_log *log;
+ char devdir[16];
+
+ B43_WARN_ON(!dev);
+ e = kzalloc(sizeof(*e), GFP_KERNEL);
+ if (!e) {
+ b43err(dev->wl, "debugfs: add device OOM\n");
+ return;
+ }
+ e->dev = dev;
+ log = &e->txstatlog;
+ log->log = kcalloc(B43_NR_LOGGED_TXSTATUS,
+ sizeof(struct b43_txstatus), GFP_KERNEL);
+ if (!log->log) {
+ b43err(dev->wl, "debugfs: add device txstatus OOM\n");
+ kfree(e);
+ return;
+ }
+ log->end = -1;
+ spin_lock_init(&log->lock);
+
+ dev->dfsentry = e;
+
+ snprintf(devdir, sizeof(devdir), "%s", wiphy_name(dev->wl->hw->wiphy));
+ e->subdir = debugfs_create_dir(devdir, rootdir);
+ if (!e->subdir || IS_ERR(e->subdir)) {
+ if (e->subdir == ERR_PTR(-ENODEV)) {
+ b43dbg(dev->wl, "DebugFS (CONFIG_DEBUG_FS) not "
+ "enabled in kernel config\n");
+ } else {
+ b43err(dev->wl, "debugfs: cannot create %s directory\n",
+ devdir);
+ }
+ dev->dfsentry = NULL;
+ kfree(log->log);
+ kfree(e);
+ return;
+ }
+
+#define ADD_FILE(name, mode) \
+ do { \
+ struct dentry *d; \
+ d = debugfs_create_file(__stringify(name), \
+ mode, e->subdir, dev, \
+ &fops_##name.fops); \
+ e->file_##name.dentry = NULL; \
+ if (!IS_ERR(d)) \
+ e->file_##name.dentry = d; \
+ } while (0)
+
+
+ ADD_FILE(tsf, 0600);
+ ADD_FILE(ucode_regs, 0400);
+ ADD_FILE(shm, 0400);
+ ADD_FILE(txstat, 0400);
+ ADD_FILE(txpower_g, 0600);
+ ADD_FILE(restart, 0200);
+ ADD_FILE(loctls, 0400);
+
+#undef ADD_FILE
+
+ b43_add_dynamic_debug(dev);
+}
+
+void b43_debugfs_remove_device(struct b43_wldev *dev)
+{
+ struct b43_dfsentry *e;
+
+ if (!dev)
+ return;
+ e = dev->dfsentry;
+ if (!e)
+ return;
+ b43_remove_dynamic_debug(dev);
+
+ debugfs_remove(e->file_tsf.dentry);
+ debugfs_remove(e->file_ucode_regs.dentry);
+ debugfs_remove(e->file_shm.dentry);
+ debugfs_remove(e->file_txstat.dentry);
+ debugfs_remove(e->file_txpower_g.dentry);
+ debugfs_remove(e->file_restart.dentry);
+ debugfs_remove(e->file_loctls.dentry);
+
+ debugfs_remove(e->subdir);
+ kfree(e->txstatlog.log);
+ kfree(e);
+}
+
+void b43_debugfs_log_txstat(struct b43_wldev *dev,
+ const struct b43_txstatus *status)
+{
+ struct b43_dfsentry *e = dev->dfsentry;
+ struct b43_txstatus_log *log;
+ struct b43_txstatus *cur;
+ int i;
+
+ if (!e)
+ return;
+ log = &e->txstatlog;
+ B43_WARN_ON(!irqs_disabled());
+ spin_lock(&log->lock);
+ i = log->end + 1;
+ if (i == B43_NR_LOGGED_TXSTATUS)
+ i = 0;
+ log->end = i;
+ cur = &(log->log[i]);
+ memcpy(cur, status, sizeof(*cur));
+ spin_unlock(&log->lock);
+}
+
+void b43_debugfs_init(void)
+{
+ rootdir = debugfs_create_dir(KBUILD_MODNAME, NULL);
+ if (IS_ERR(rootdir))
+ rootdir = NULL;
+}
+
+void b43_debugfs_exit(void)
+{
+ debugfs_remove(rootdir);
+}
--- /dev/null
+#ifndef B43_DEBUGFS_H_
+#define B43_DEBUGFS_H_
+
+struct b43_wldev;
+struct b43_txstatus;
+
+enum b43_dyndbg { /* Dynamic debugging features */
+ B43_DBG_XMITPOWER,
+ B43_DBG_DMAOVERFLOW,
+ B43_DBG_DMAVERBOSE,
+ B43_DBG_PWORK_FAST,
+ B43_DBG_PWORK_STOP,
+ __B43_NR_DYNDBG,
+};
+
+#ifdef CONFIG_B43_DEBUG
+
+struct dentry;
+
+#define B43_NR_LOGGED_TXSTATUS 100
+
+struct b43_txstatus_log {
+ struct b43_txstatus *log;
+ int end;
+ spinlock_t lock;
+};
+
+struct b43_dfs_file {
+ struct dentry *dentry;
+ char *buffer;
+ size_t data_len;
+};
+
+struct b43_dfsentry {
+ struct b43_wldev *dev;
+ struct dentry *subdir;
+
+ struct b43_dfs_file file_tsf;
+ struct b43_dfs_file file_ucode_regs;
+ struct b43_dfs_file file_shm;
+ struct b43_dfs_file file_txstat;
+ struct b43_dfs_file file_txpower_g;
+ struct b43_dfs_file file_restart;
+ struct b43_dfs_file file_loctls;
+
+ struct b43_txstatus_log txstatlog;
+
+ /* Enabled/Disabled list for the dynamic debugging features. */
+ u32 dyn_debug[__B43_NR_DYNDBG];
+ /* Dentries for the dynamic debugging entries. */
+ struct dentry *dyn_debug_dentries[__B43_NR_DYNDBG];
+};
+
+int b43_debug(struct b43_wldev *dev, enum b43_dyndbg feature);
+
+void b43_debugfs_init(void);
+void b43_debugfs_exit(void);
+void b43_debugfs_add_device(struct b43_wldev *dev);
+void b43_debugfs_remove_device(struct b43_wldev *dev);
+void b43_debugfs_log_txstat(struct b43_wldev *dev,
+ const struct b43_txstatus *status);
+
+#else /* CONFIG_B43_DEBUG */
+
+static inline int b43_debug(struct b43_wldev *dev, enum b43_dyndbg feature)
+{
+ return 0;
+}
+
+static inline void b43_debugfs_init(void)
+{
+}
+static inline void b43_debugfs_exit(void)
+{
+}
+static inline void b43_debugfs_add_device(struct b43_wldev *dev)
+{
+}
+static inline void b43_debugfs_remove_device(struct b43_wldev *dev)
+{
+}
+static inline void b43_debugfs_log_txstat(struct b43_wldev *dev,
+ const struct b43_txstatus *status)
+{
+}
+
+#endif /* CONFIG_B43_DEBUG */
+
+#endif /* B43_DEBUGFS_H_ */
--- /dev/null
+/*
+
+ Broadcom B43 wireless driver
+
+ DMA ringbuffer and descriptor allocation/management
+
+ Copyright (c) 2005, 2006 Michael Buesch <mb@bu3sch.de>
+
+ Some code in this file is derived from the b44.c driver
+ Copyright (C) 2002 David S. Miller
+ Copyright (C) Pekka Pietikainen
+
+ This program is free software; you can redistribute it and/or modify
+ it under the terms of the GNU General Public License as published by
+ the Free Software Foundation; either version 2 of the License, or
+ (at your option) any later version.
+
+ This program is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ GNU General Public License for more details.
+
+ You should have received a copy of the GNU General Public License
+ along with this program; see the file COPYING. If not, write to
+ the Free Software Foundation, Inc., 51 Franklin Steet, Fifth Floor,
+ Boston, MA 02110-1301, USA.
+
+*/
+
+#include "b43.h"
+#include "dma.h"
+#include "main.h"
+#include "debugfs.h"
+#include "xmit.h"
+
+#include <linux/dma-mapping.h>
+#include <linux/pci.h>
+#include <linux/delay.h>
+#include <linux/skbuff.h>
+
+/* 32bit DMA ops. */
+static
+struct b43_dmadesc_generic *op32_idx2desc(struct b43_dmaring *ring,
+ int slot,
+ struct b43_dmadesc_meta **meta)
+{
+ struct b43_dmadesc32 *desc;
+
+ *meta = &(ring->meta[slot]);
+ desc = ring->descbase;
+ desc = &(desc[slot]);
+
+ return (struct b43_dmadesc_generic *)desc;
+}
+
+static void op32_fill_descriptor(struct b43_dmaring *ring,
+ struct b43_dmadesc_generic *desc,
+ dma_addr_t dmaaddr, u16 bufsize,
+ int start, int end, int irq)
+{
+ struct b43_dmadesc32 *descbase = ring->descbase;
+ int slot;
+ u32 ctl;
+ u32 addr;
+ u32 addrext;
+
+ slot = (int)(&(desc->dma32) - descbase);
+ B43_WARN_ON(!(slot >= 0 && slot < ring->nr_slots));
+
+ addr = (u32) (dmaaddr & ~SSB_DMA_TRANSLATION_MASK);
+ addrext = (u32) (dmaaddr & SSB_DMA_TRANSLATION_MASK)
+ >> SSB_DMA_TRANSLATION_SHIFT;
+ addr |= ssb_dma_translation(ring->dev->dev);
+ ctl = (bufsize - ring->frameoffset)
+ & B43_DMA32_DCTL_BYTECNT;
+ if (slot == ring->nr_slots - 1)
+ ctl |= B43_DMA32_DCTL_DTABLEEND;
+ if (start)
+ ctl |= B43_DMA32_DCTL_FRAMESTART;
+ if (end)
+ ctl |= B43_DMA32_DCTL_FRAMEEND;
+ if (irq)
+ ctl |= B43_DMA32_DCTL_IRQ;
+ ctl |= (addrext << B43_DMA32_DCTL_ADDREXT_SHIFT)
+ & B43_DMA32_DCTL_ADDREXT_MASK;
+
+ desc->dma32.control = cpu_to_le32(ctl);
+ desc->dma32.address = cpu_to_le32(addr);
+}
+
+static void op32_poke_tx(struct b43_dmaring *ring, int slot)
+{
+ b43_dma_write(ring, B43_DMA32_TXINDEX,
+ (u32) (slot * sizeof(struct b43_dmadesc32)));
+}
+
+static void op32_tx_suspend(struct b43_dmaring *ring)
+{
+ b43_dma_write(ring, B43_DMA32_TXCTL, b43_dma_read(ring, B43_DMA32_TXCTL)
+ | B43_DMA32_TXSUSPEND);
+}
+
+static void op32_tx_resume(struct b43_dmaring *ring)
+{
+ b43_dma_write(ring, B43_DMA32_TXCTL, b43_dma_read(ring, B43_DMA32_TXCTL)
+ & ~B43_DMA32_TXSUSPEND);
+}
+
+static int op32_get_current_rxslot(struct b43_dmaring *ring)
+{
+ u32 val;
+
+ val = b43_dma_read(ring, B43_DMA32_RXSTATUS);
+ val &= B43_DMA32_RXDPTR;
+
+ return (val / sizeof(struct b43_dmadesc32));
+}
+
+static void op32_set_current_rxslot(struct b43_dmaring *ring, int slot)
+{
+ b43_dma_write(ring, B43_DMA32_RXINDEX,
+ (u32) (slot * sizeof(struct b43_dmadesc32)));
+}
+
+static const struct b43_dma_ops dma32_ops = {
+ .idx2desc = op32_idx2desc,
+ .fill_descriptor = op32_fill_descriptor,
+ .poke_tx = op32_poke_tx,
+ .tx_suspend = op32_tx_suspend,
+ .tx_resume = op32_tx_resume,
+ .get_current_rxslot = op32_get_current_rxslot,
+ .set_current_rxslot = op32_set_current_rxslot,
+};
+
+/* 64bit DMA ops. */
+static
+struct b43_dmadesc_generic *op64_idx2desc(struct b43_dmaring *ring,
+ int slot,
+ struct b43_dmadesc_meta **meta)
+{
+ struct b43_dmadesc64 *desc;
+
+ *meta = &(ring->meta[slot]);
+ desc = ring->descbase;
+ desc = &(desc[slot]);
+
+ return (struct b43_dmadesc_generic *)desc;
+}
+
+static void op64_fill_descriptor(struct b43_dmaring *ring,
+ struct b43_dmadesc_generic *desc,
+ dma_addr_t dmaaddr, u16 bufsize,
+ int start, int end, int irq)
+{
+ struct b43_dmadesc64 *descbase = ring->descbase;
+ int slot;
+ u32 ctl0 = 0, ctl1 = 0;
+ u32 addrlo, addrhi;
+ u32 addrext;
+
+ slot = (int)(&(desc->dma64) - descbase);
+ B43_WARN_ON(!(slot >= 0 && slot < ring->nr_slots));
+
+ addrlo = (u32) (dmaaddr & 0xFFFFFFFF);
+ addrhi = (((u64) dmaaddr >> 32) & ~SSB_DMA_TRANSLATION_MASK);
+ addrext = (((u64) dmaaddr >> 32) & SSB_DMA_TRANSLATION_MASK)
+ >> SSB_DMA_TRANSLATION_SHIFT;
+ addrhi |= ssb_dma_translation(ring->dev->dev);
+ if (slot == ring->nr_slots - 1)
+ ctl0 |= B43_DMA64_DCTL0_DTABLEEND;
+ if (start)
+ ctl0 |= B43_DMA64_DCTL0_FRAMESTART;
+ if (end)
+ ctl0 |= B43_DMA64_DCTL0_FRAMEEND;
+ if (irq)
+ ctl0 |= B43_DMA64_DCTL0_IRQ;
+ ctl1 |= (bufsize - ring->frameoffset)
+ & B43_DMA64_DCTL1_BYTECNT;
+ ctl1 |= (addrext << B43_DMA64_DCTL1_ADDREXT_SHIFT)
+ & B43_DMA64_DCTL1_ADDREXT_MASK;
+
+ desc->dma64.control0 = cpu_to_le32(ctl0);
+ desc->dma64.control1 = cpu_to_le32(ctl1);
+ desc->dma64.address_low = cpu_to_le32(addrlo);
+ desc->dma64.address_high = cpu_to_le32(addrhi);
+}
+
+static void op64_poke_tx(struct b43_dmaring *ring, int slot)
+{
+ b43_dma_write(ring, B43_DMA64_TXINDEX,
+ (u32) (slot * sizeof(struct b43_dmadesc64)));
+}
+
+static void op64_tx_suspend(struct b43_dmaring *ring)
+{
+ b43_dma_write(ring, B43_DMA64_TXCTL, b43_dma_read(ring, B43_DMA64_TXCTL)
+ | B43_DMA64_TXSUSPEND);
+}
+
+static void op64_tx_resume(struct b43_dmaring *ring)
+{
+ b43_dma_write(ring, B43_DMA64_TXCTL, b43_dma_read(ring, B43_DMA64_TXCTL)
+ & ~B43_DMA64_TXSUSPEND);
+}
+
+static int op64_get_current_rxslot(struct b43_dmaring *ring)
+{
+ u32 val;
+
+ val = b43_dma_read(ring, B43_DMA64_RXSTATUS);
+ val &= B43_DMA64_RXSTATDPTR;
+
+ return (val / sizeof(struct b43_dmadesc64));
+}
+
+static void op64_set_current_rxslot(struct b43_dmaring *ring, int slot)
+{
+ b43_dma_write(ring, B43_DMA64_RXINDEX,
+ (u32) (slot * sizeof(struct b43_dmadesc64)));
+}
+
+static const struct b43_dma_ops dma64_ops = {
+ .idx2desc = op64_idx2desc,
+ .fill_descriptor = op64_fill_descriptor,
+ .poke_tx = op64_poke_tx,
+ .tx_suspend = op64_tx_suspend,
+ .tx_resume = op64_tx_resume,
+ .get_current_rxslot = op64_get_current_rxslot,
+ .set_current_rxslot = op64_set_current_rxslot,
+};
+
+static inline int free_slots(struct b43_dmaring *ring)
+{
+ return (ring->nr_slots - ring->used_slots);
+}
+
+static inline int next_slot(struct b43_dmaring *ring, int slot)
+{
+ B43_WARN_ON(!(slot >= -1 && slot <= ring->nr_slots - 1));
+ if (slot == ring->nr_slots - 1)
+ return 0;
+ return slot + 1;
+}
+
+static inline int prev_slot(struct b43_dmaring *ring, int slot)
+{
+ B43_WARN_ON(!(slot >= 0 && slot <= ring->nr_slots - 1));
+ if (slot == 0)
+ return ring->nr_slots - 1;
+ return slot - 1;
+}
+
+#ifdef CONFIG_B43_DEBUG
+static void update_max_used_slots(struct b43_dmaring *ring,
+ int current_used_slots)
+{
+ if (current_used_slots <= ring->max_used_slots)
+ return;
+ ring->max_used_slots = current_used_slots;
+ if (b43_debug(ring->dev, B43_DBG_DMAVERBOSE)) {
+ b43dbg(ring->dev->wl,
+ "max_used_slots increased to %d on %s ring %d\n",
+ ring->max_used_slots,
+ ring->tx ? "TX" : "RX", ring->index);
+ }
+}
+#else
+static inline
+ void update_max_used_slots(struct b43_dmaring *ring, int current_used_slots)
+{
+}
+#endif /* DEBUG */
+
+/* Request a slot for usage. */
+static inline int request_slot(struct b43_dmaring *ring)
+{
+ int slot;
+
+ B43_WARN_ON(!ring->tx);
+ B43_WARN_ON(ring->stopped);
+ B43_WARN_ON(free_slots(ring) == 0);
+
+ slot = next_slot(ring, ring->current_slot);
+ ring->current_slot = slot;
+ ring->used_slots++;
+
+ update_max_used_slots(ring, ring->used_slots);
+
+ return slot;
+}
+
+/* Mac80211-queue to b43-ring mapping */
+static struct b43_dmaring *priority_to_txring(struct b43_wldev *dev,
+ int queue_priority)
+{
+ struct b43_dmaring *ring;
+
+/*FIXME: For now we always run on TX-ring-1 */
+ return dev->dma.tx_ring1;
+
+ /* 0 = highest priority */
+ switch (queue_priority) {
+ default:
+ B43_WARN_ON(1);
+ /* fallthrough */
+ case 0:
+ ring = dev->dma.tx_ring3;
+ break;
+ case 1:
+ ring = dev->dma.tx_ring2;
+ break;
+ case 2:
+ ring = dev->dma.tx_ring1;
+ break;
+ case 3:
+ ring = dev->dma.tx_ring0;
+ break;
+ case 4:
+ ring = dev->dma.tx_ring4;
+ break;
+ case 5:
+ ring = dev->dma.tx_ring5;
+ break;
+ }
+
+ return ring;
+}
+
+/* Bcm43xx-ring to mac80211-queue mapping */
+static inline int txring_to_priority(struct b43_dmaring *ring)
+{
+ static const u8 idx_to_prio[] = { 3, 2, 1, 0, 4, 5, };
+
+/*FIXME: have only one queue, for now */
+ return 0;
+
+ return idx_to_prio[ring->index];
+}
+
+u16 b43_dmacontroller_base(int dma64bit, int controller_idx)
+{
+ static const u16 map64[] = {
+ B43_MMIO_DMA64_BASE0,
+ B43_MMIO_DMA64_BASE1,
+ B43_MMIO_DMA64_BASE2,
+ B43_MMIO_DMA64_BASE3,
+ B43_MMIO_DMA64_BASE4,
+ B43_MMIO_DMA64_BASE5,
+ };
+ static const u16 map32[] = {
+ B43_MMIO_DMA32_BASE0,
+ B43_MMIO_DMA32_BASE1,
+ B43_MMIO_DMA32_BASE2,
+ B43_MMIO_DMA32_BASE3,
+ B43_MMIO_DMA32_BASE4,
+ B43_MMIO_DMA32_BASE5,
+ };
+
+ if (dma64bit) {
+ B43_WARN_ON(!(controller_idx >= 0 &&
+ controller_idx < ARRAY_SIZE(map64)));
+ return map64[controller_idx];
+ }
+ B43_WARN_ON(!(controller_idx >= 0 &&
+ controller_idx < ARRAY_SIZE(map32)));
+ return map32[controller_idx];
+}
+
+static inline
+ dma_addr_t map_descbuffer(struct b43_dmaring *ring,
+ unsigned char *buf, size_t len, int tx)
+{
+ dma_addr_t dmaaddr;
+
+ if (tx) {
+ dmaaddr = dma_map_single(ring->dev->dev->dev,
+ buf, len, DMA_TO_DEVICE);
+ } else {
+ dmaaddr = dma_map_single(ring->dev->dev->dev,
+ buf, len, DMA_FROM_DEVICE);
+ }
+
+ return dmaaddr;
+}
+
+static inline
+ void unmap_descbuffer(struct b43_dmaring *ring,
+ dma_addr_t addr, size_t len, int tx)
+{
+ if (tx) {
+ dma_unmap_single(ring->dev->dev->dev, addr, len, DMA_TO_DEVICE);
+ } else {
+ dma_unmap_single(ring->dev->dev->dev,
+ addr, len, DMA_FROM_DEVICE);
+ }
+}
+
+static inline
+ void sync_descbuffer_for_cpu(struct b43_dmaring *ring,
+ dma_addr_t addr, size_t len)
+{
+ B43_WARN_ON(ring->tx);
+ dma_sync_single_for_cpu(ring->dev->dev->dev,
+ addr, len, DMA_FROM_DEVICE);
+}
+
+static inline
+ void sync_descbuffer_for_device(struct b43_dmaring *ring,
+ dma_addr_t addr, size_t len)
+{
+ B43_WARN_ON(ring->tx);
+ dma_sync_single_for_device(ring->dev->dev->dev,
+ addr, len, DMA_FROM_DEVICE);
+}
+
+static inline
+ void free_descriptor_buffer(struct b43_dmaring *ring,
+ struct b43_dmadesc_meta *meta)
+{
+ if (meta->skb) {
+ dev_kfree_skb_any(meta->skb);
+ meta->skb = NULL;
+ }
+}
+
+static int alloc_ringmemory(struct b43_dmaring *ring)
+{
+ struct device *dev = ring->dev->dev->dev;
+
+ ring->descbase = dma_alloc_coherent(dev, B43_DMA_RINGMEMSIZE,
+ &(ring->dmabase), GFP_KERNEL);
+ if (!ring->descbase) {
+ b43err(ring->dev->wl, "DMA ringmemory allocation failed\n");
+ return -ENOMEM;
+ }
+ memset(ring->descbase, 0, B43_DMA_RINGMEMSIZE);
+
+ return 0;
+}
+
+static void free_ringmemory(struct b43_dmaring *ring)
+{
+ struct device *dev = ring->dev->dev->dev;
+
+ dma_free_coherent(dev, B43_DMA_RINGMEMSIZE,
+ ring->descbase, ring->dmabase);
+}
+
+/* Reset the RX DMA channel */
+int b43_dmacontroller_rx_reset(struct b43_wldev *dev, u16 mmio_base, int dma64)
+{
+ int i;
+ u32 value;
+ u16 offset;
+
+ might_sleep();
+
+ offset = dma64 ? B43_DMA64_RXCTL : B43_DMA32_RXCTL;
+ b43_write32(dev, mmio_base + offset, 0);
+ for (i = 0; i < 10; i++) {
+ offset = dma64 ? B43_DMA64_RXSTATUS : B43_DMA32_RXSTATUS;
+ value = b43_read32(dev, mmio_base + offset);
+ if (dma64) {
+ value &= B43_DMA64_RXSTAT;
+ if (value == B43_DMA64_RXSTAT_DISABLED) {
+ i = -1;
+ break;
+ }
+ } else {
+ value &= B43_DMA32_RXSTATE;
+ if (value == B43_DMA32_RXSTAT_DISABLED) {
+ i = -1;
+ break;
+ }
+ }
+ msleep(1);
+ }
+ if (i != -1) {
+ b43err(dev->wl, "DMA RX reset timed out\n");
+ return -ENODEV;
+ }
+
+ return 0;
+}
+
+/* Reset the RX DMA channel */
+int b43_dmacontroller_tx_reset(struct b43_wldev *dev, u16 mmio_base, int dma64)
+{
+ int i;
+ u32 value;
+ u16 offset;
+
+ might_sleep();
+
+ for (i = 0; i < 10; i++) {
+ offset = dma64 ? B43_DMA64_TXSTATUS : B43_DMA32_TXSTATUS;
+ value = b43_read32(dev, mmio_base + offset);
+ if (dma64) {
+ value &= B43_DMA64_TXSTAT;
+ if (value == B43_DMA64_TXSTAT_DISABLED ||
+ value == B43_DMA64_TXSTAT_IDLEWAIT ||
+ value == B43_DMA64_TXSTAT_STOPPED)
+ break;
+ } else {
+ value &= B43_DMA32_TXSTATE;
+ if (value == B43_DMA32_TXSTAT_DISABLED ||
+ value == B43_DMA32_TXSTAT_IDLEWAIT ||
+ value == B43_DMA32_TXSTAT_STOPPED)
+ break;
+ }
+ msleep(1);
+ }
+ offset = dma64 ? B43_DMA64_TXCTL : B43_DMA32_TXCTL;
+ b43_write32(dev, mmio_base + offset, 0);
+ for (i = 0; i < 10; i++) {
+ offset = dma64 ? B43_DMA64_TXSTATUS : B43_DMA32_TXSTATUS;
+ value = b43_read32(dev, mmio_base + offset);
+ if (dma64) {
+ value &= B43_DMA64_TXSTAT;
+ if (value == B43_DMA64_TXSTAT_DISABLED) {
+ i = -1;
+ break;
+ }
+ } else {
+ value &= B43_DMA32_TXSTATE;
+ if (value == B43_DMA32_TXSTAT_DISABLED) {
+ i = -1;
+ break;
+ }
+ }
+ msleep(1);
+ }
+ if (i != -1) {
+ b43err(dev->wl, "DMA TX reset timed out\n");
+ return -ENODEV;
+ }
+ /* ensure the reset is completed. */
+ msleep(1);
+
+ return 0;
+}
+
+static int setup_rx_descbuffer(struct b43_dmaring *ring,
+ struct b43_dmadesc_generic *desc,
+ struct b43_dmadesc_meta *meta, gfp_t gfp_flags)
+{
+ struct b43_rxhdr_fw4 *rxhdr;
+ struct b43_hwtxstatus *txstat;
+ dma_addr_t dmaaddr;
+ struct sk_buff *skb;
+
+ B43_WARN_ON(ring->tx);
+
+ skb = __dev_alloc_skb(ring->rx_buffersize, gfp_flags);
+ if (unlikely(!skb))
+ return -ENOMEM;
+ dmaaddr = map_descbuffer(ring, skb->data, ring->rx_buffersize, 0);
+ if (dma_mapping_error(dmaaddr)) {
+ /* ugh. try to realloc in zone_dma */
+ gfp_flags |= GFP_DMA;
+
+ dev_kfree_skb_any(skb);
+
+ skb = __dev_alloc_skb(ring->rx_buffersize, gfp_flags);
+ if (unlikely(!skb))
+ return -ENOMEM;
+ dmaaddr = map_descbuffer(ring, skb->data,
+ ring->rx_buffersize, 0);
+ }
+
+ if (dma_mapping_error(dmaaddr)) {
+ dev_kfree_skb_any(skb);
+ return -EIO;
+ }
+
+ meta->skb = skb;
+ meta->dmaaddr = dmaaddr;
+ ring->ops->fill_descriptor(ring, desc, dmaaddr,
+ ring->rx_buffersize, 0, 0, 0);
+
+ rxhdr = (struct b43_rxhdr_fw4 *)(skb->data);
+ rxhdr->frame_len = 0;
+ txstat = (struct b43_hwtxstatus *)(skb->data);
+ txstat->cookie = 0;
+
+ return 0;
+}
+
+/* Allocate the initial descbuffers.
+ * This is used for an RX ring only.
+ */
+static int alloc_initial_descbuffers(struct b43_dmaring *ring)
+{
+ int i, err = -ENOMEM;
+ struct b43_dmadesc_generic *desc;
+ struct b43_dmadesc_meta *meta;
+
+ for (i = 0; i < ring->nr_slots; i++) {
+ desc = ring->ops->idx2desc(ring, i, &meta);
+
+ err = setup_rx_descbuffer(ring, desc, meta, GFP_KERNEL);
+ if (err) {
+ b43err(ring->dev->wl,
+ "Failed to allocate initial descbuffers\n");
+ goto err_unwind;
+ }
+ }
+ mb();
+ ring->used_slots = ring->nr_slots;
+ err = 0;
+ out:
+ return err;
+
+ err_unwind:
+ for (i--; i >= 0; i--) {
+ desc = ring->ops->idx2desc(ring, i, &meta);
+
+ unmap_descbuffer(ring, meta->dmaaddr, ring->rx_buffersize, 0);
+ dev_kfree_skb(meta->skb);
+ }
+ goto out;
+}
+
+/* Do initial setup of the DMA controller.
+ * Reset the controller, write the ring busaddress
+ * and switch the "enable" bit on.
+ */
+static int dmacontroller_setup(struct b43_dmaring *ring)
+{
+ int err = 0;
+ u32 value;
+ u32 addrext;
+ u32 trans = ssb_dma_translation(ring->dev->dev);
+
+ if (ring->tx) {
+ if (ring->dma64) {
+ u64 ringbase = (u64) (ring->dmabase);
+
+ addrext = ((ringbase >> 32) & SSB_DMA_TRANSLATION_MASK)
+ >> SSB_DMA_TRANSLATION_SHIFT;
+ value = B43_DMA64_TXENABLE;
+ value |= (addrext << B43_DMA64_TXADDREXT_SHIFT)
+ & B43_DMA64_TXADDREXT_MASK;
+ b43_dma_write(ring, B43_DMA64_TXCTL, value);
+ b43_dma_write(ring, B43_DMA64_TXRINGLO,
+ (ringbase & 0xFFFFFFFF));
+ b43_dma_write(ring, B43_DMA64_TXRINGHI,
+ ((ringbase >> 32) &
+ ~SSB_DMA_TRANSLATION_MASK)
+ | trans);
+ } else {
+ u32 ringbase = (u32) (ring->dmabase);
+
+ addrext = (ringbase & SSB_DMA_TRANSLATION_MASK)
+ >> SSB_DMA_TRANSLATION_SHIFT;
+ value = B43_DMA32_TXENABLE;
+ value |= (addrext << B43_DMA32_TXADDREXT_SHIFT)
+ & B43_DMA32_TXADDREXT_MASK;
+ b43_dma_write(ring, B43_DMA32_TXCTL, value);
+ b43_dma_write(ring, B43_DMA32_TXRING,
+ (ringbase & ~SSB_DMA_TRANSLATION_MASK)
+ | trans);
+ }
+ } else {
+ err = alloc_initial_descbuffers(ring);
+ if (err)
+ goto out;
+ if (ring->dma64) {
+ u64 ringbase = (u64) (ring->dmabase);
+
+ addrext = ((ringbase >> 32) & SSB_DMA_TRANSLATION_MASK)
+ >> SSB_DMA_TRANSLATION_SHIFT;
+ value = (ring->frameoffset << B43_DMA64_RXFROFF_SHIFT);
+ value |= B43_DMA64_RXENABLE;
+ value |= (addrext << B43_DMA64_RXADDREXT_SHIFT)
+ & B43_DMA64_RXADDREXT_MASK;
+ b43_dma_write(ring, B43_DMA64_RXCTL, value);
+ b43_dma_write(ring, B43_DMA64_RXRINGLO,
+ (ringbase & 0xFFFFFFFF));
+ b43_dma_write(ring, B43_DMA64_RXRINGHI,
+ ((ringbase >> 32) &
+ ~SSB_DMA_TRANSLATION_MASK)
+ | trans);
+ b43_dma_write(ring, B43_DMA64_RXINDEX, 200);
+ } else {
+ u32 ringbase = (u32) (ring->dmabase);
+
+ addrext = (ringbase & SSB_DMA_TRANSLATION_MASK)
+ >> SSB_DMA_TRANSLATION_SHIFT;
+ value = (ring->frameoffset << B43_DMA32_RXFROFF_SHIFT);
+ value |= B43_DMA32_RXENABLE;
+ value |= (addrext << B43_DMA32_RXADDREXT_SHIFT)
+ & B43_DMA32_RXADDREXT_MASK;
+ b43_dma_write(ring, B43_DMA32_RXCTL, value);
+ b43_dma_write(ring, B43_DMA32_RXRING,
+ (ringbase & ~SSB_DMA_TRANSLATION_MASK)
+ | trans);
+ b43_dma_write(ring, B43_DMA32_RXINDEX, 200);
+ }
+ }
+
+ out:
+ return err;
+}
+
+/* Shutdown the DMA controller. */
+static void dmacontroller_cleanup(struct b43_dmaring *ring)
+{
+ if (ring->tx) {
+ b43_dmacontroller_tx_reset(ring->dev, ring->mmio_base,
+ ring->dma64);
+ if (ring->dma64) {
+ b43_dma_write(ring, B43_DMA64_TXRINGLO, 0);
+ b43_dma_write(ring, B43_DMA64_TXRINGHI, 0);
+ } else
+ b43_dma_write(ring, B43_DMA32_TXRING, 0);
+ } else {
+ b43_dmacontroller_rx_reset(ring->dev, ring->mmio_base,
+ ring->dma64);
+ if (ring->dma64) {
+ b43_dma_write(ring, B43_DMA64_RXRINGLO, 0);
+ b43_dma_write(ring, B43_DMA64_RXRINGHI, 0);
+ } else
+ b43_dma_write(ring, B43_DMA32_RXRING, 0);
+ }
+}
+
+static void free_all_descbuffers(struct b43_dmaring *ring)
+{
+ struct b43_dmadesc_generic *desc;
+ struct b43_dmadesc_meta *meta;
+ int i;
+
+ if (!ring->used_slots)
+ return;
+ for (i = 0; i < ring->nr_slots; i++) {
+ desc = ring->ops->idx2desc(ring, i, &meta);
+
+ if (!meta->skb) {
+ B43_WARN_ON(!ring->tx);
+ continue;
+ }
+ if (ring->tx) {
+ unmap_descbuffer(ring, meta->dmaaddr,
+ meta->skb->len, 1);
+ } else {
+ unmap_descbuffer(ring, meta->dmaaddr,
+ ring->rx_buffersize, 0);
+ }
+ free_descriptor_buffer(ring, meta);
+ }
+}
+
+static u64 supported_dma_mask(struct b43_wldev *dev)
+{
+ u32 tmp;
+ u16 mmio_base;
+
+ tmp = b43_read32(dev, SSB_TMSHIGH);
+ if (tmp & SSB_TMSHIGH_DMA64)
+ return DMA_64BIT_MASK;
+ mmio_base = b43_dmacontroller_base(0, 0);
+ b43_write32(dev, mmio_base + B43_DMA32_TXCTL, B43_DMA32_TXADDREXT_MASK);
+ tmp = b43_read32(dev, mmio_base + B43_DMA32_TXCTL);
+ if (tmp & B43_DMA32_TXADDREXT_MASK)
+ return DMA_32BIT_MASK;
+
+ return DMA_30BIT_MASK;
+}
+
+/* Main initialization function. */
+static
+struct b43_dmaring *b43_setup_dmaring(struct b43_wldev *dev,
+ int controller_index,
+ int for_tx, int dma64)
+{
+ struct b43_dmaring *ring;
+ int err;
+ int nr_slots;
+ dma_addr_t dma_test;
+
+ ring = kzalloc(sizeof(*ring), GFP_KERNEL);
+ if (!ring)
+ goto out;
+
+ nr_slots = B43_RXRING_SLOTS;
+ if (for_tx)
+ nr_slots = B43_TXRING_SLOTS;
+
+ ring->meta = kcalloc(nr_slots, sizeof(struct b43_dmadesc_meta),
+ GFP_KERNEL);
+ if (!ring->meta)
+ goto err_kfree_ring;
+ if (for_tx) {
+ ring->txhdr_cache = kcalloc(nr_slots,
+ sizeof(struct b43_txhdr_fw4),
+ GFP_KERNEL);
+ if (!ring->txhdr_cache)
+ goto err_kfree_meta;
+
+ /* test for ability to dma to txhdr_cache */
+ dma_test = dma_map_single(dev->dev->dev,
+ ring->txhdr_cache,
+ sizeof(struct b43_txhdr_fw4),
+ DMA_TO_DEVICE);
+
+ if (dma_mapping_error(dma_test)) {
+ /* ugh realloc */
+ kfree(ring->txhdr_cache);
+ ring->txhdr_cache = kcalloc(nr_slots,
+ sizeof(struct
+ b43_txhdr_fw4),
+ GFP_KERNEL | GFP_DMA);
+ if (!ring->txhdr_cache)
+ goto err_kfree_meta;
+
+ dma_test = dma_map_single(dev->dev->dev,
+ ring->txhdr_cache,
+ sizeof(struct b43_txhdr_fw4),
+ DMA_TO_DEVICE);
+
+ if (dma_mapping_error(dma_test))
+ goto err_kfree_txhdr_cache;
+ }
+
+ dma_unmap_single(dev->dev->dev,
+ dma_test, sizeof(struct b43_txhdr_fw4),
+ DMA_TO_DEVICE);
+ }
+
+ ring->dev = dev;
+ ring->nr_slots = nr_slots;
+ ring->mmio_base = b43_dmacontroller_base(dma64, controller_index);
+ ring->index = controller_index;
+ ring->dma64 = !!dma64;
+ if (dma64)
+ ring->ops = &dma64_ops;
+ else
+ ring->ops = &dma32_ops;
+ if (for_tx) {
+ ring->tx = 1;
+ ring->current_slot = -1;
+ } else {
+ if (ring->index == 0) {
+ ring->rx_buffersize = B43_DMA0_RX_BUFFERSIZE;
+ ring->frameoffset = B43_DMA0_RX_FRAMEOFFSET;
+ } else if (ring->index == 3) {
+ ring->rx_buffersize = B43_DMA3_RX_BUFFERSIZE;
+ ring->frameoffset = B43_DMA3_RX_FRAMEOFFSET;
+ } else
+ B43_WARN_ON(1);
+ }
+ spin_lock_init(&ring->lock);
+#ifdef CONFIG_B43_DEBUG
+ ring->last_injected_overflow = jiffies;
+#endif
+
+ err = alloc_ringmemory(ring);
+ if (err)
+ goto err_kfree_txhdr_cache;
+ err = dmacontroller_setup(ring);
+ if (err)
+ goto err_free_ringmemory;
+
+ out:
+ return ring;
+
+ err_free_ringmemory:
+ free_ringmemory(ring);
+ err_kfree_txhdr_cache:
+ kfree(ring->txhdr_cache);
+ err_kfree_meta:
+ kfree(ring->meta);
+ err_kfree_ring:
+ kfree(ring);
+ ring = NULL;
+ goto out;
+}
+
+/* Main cleanup function. */
+static void b43_destroy_dmaring(struct b43_dmaring *ring)
+{
+ if (!ring)
+ return;
+
+ b43dbg(ring->dev->wl, "DMA-%s 0x%04X (%s) max used slots: %d/%d\n",
+ (ring->dma64) ? "64" : "32",
+ ring->mmio_base,
+ (ring->tx) ? "TX" : "RX", ring->max_used_slots, ring->nr_slots);
+ /* Device IRQs are disabled prior entering this function,
+ * so no need to take care of concurrency with rx handler stuff.
+ */
+ dmacontroller_cleanup(ring);
+ free_all_descbuffers(ring);
+ free_ringmemory(ring);
+
+ kfree(ring->txhdr_cache);
+ kfree(ring->meta);
+ kfree(ring);
+}
+
+void b43_dma_free(struct b43_wldev *dev)
+{
+ struct b43_dma *dma;
+
+ if (b43_using_pio(dev))
+ return;
+ dma = &dev->dma;
+
+ b43_destroy_dmaring(dma->rx_ring3);
+ dma->rx_ring3 = NULL;
+ b43_destroy_dmaring(dma->rx_ring0);
+ dma->rx_ring0 = NULL;
+
+ b43_destroy_dmaring(dma->tx_ring5);
+ dma->tx_ring5 = NULL;
+ b43_destroy_dmaring(dma->tx_ring4);
+ dma->tx_ring4 = NULL;
+ b43_destroy_dmaring(dma->tx_ring3);
+ dma->tx_ring3 = NULL;
+ b43_destroy_dmaring(dma->tx_ring2);
+ dma->tx_ring2 = NULL;
+ b43_destroy_dmaring(dma->tx_ring1);
+ dma->tx_ring1 = NULL;
+ b43_destroy_dmaring(dma->tx_ring0);
+ dma->tx_ring0 = NULL;
+}
+
+int b43_dma_init(struct b43_wldev *dev)
+{
+ struct b43_dma *dma = &dev->dma;
+ struct b43_dmaring *ring;
+ int err;
+ u64 dmamask;
+ int dma64 = 0;
+
+ dmamask = supported_dma_mask(dev);
+ if (dmamask == DMA_64BIT_MASK)
+ dma64 = 1;
+
+ err = ssb_dma_set_mask(dev->dev, dmamask);
+ if (err) {
+#ifdef B43_PIO
+ b43warn(dev->wl, "DMA for this device not supported. "
+ "Falling back to PIO\n");
+ dev->__using_pio = 1;
+ return -EAGAIN;
+#else
+ b43err(dev->wl, "DMA for this device not supported and "
+ "no PIO support compiled in\n");
+ return -EOPNOTSUPP;
+#endif
+ }
+
+ err = -ENOMEM;
+ /* setup TX DMA channels. */
+ ring = b43_setup_dmaring(dev, 0, 1, dma64);
+ if (!ring)
+ goto out;
+ dma->tx_ring0 = ring;
+
+ ring = b43_setup_dmaring(dev, 1, 1, dma64);
+ if (!ring)
+ goto err_destroy_tx0;
+ dma->tx_ring1 = ring;
+
+ ring = b43_setup_dmaring(dev, 2, 1, dma64);
+ if (!ring)
+ goto err_destroy_tx1;
+ dma->tx_ring2 = ring;
+
+ ring = b43_setup_dmaring(dev, 3, 1, dma64);
+ if (!ring)
+ goto err_destroy_tx2;
+ dma->tx_ring3 = ring;
+
+ ring = b43_setup_dmaring(dev, 4, 1, dma64);
+ if (!ring)
+ goto err_destroy_tx3;
+ dma->tx_ring4 = ring;
+
+ ring = b43_setup_dmaring(dev, 5, 1, dma64);
+ if (!ring)
+ goto err_destroy_tx4;
+ dma->tx_ring5 = ring;
+
+ /* setup RX DMA channels. */
+ ring = b43_setup_dmaring(dev, 0, 0, dma64);
+ if (!ring)
+ goto err_destroy_tx5;
+ dma->rx_ring0 = ring;
+
+ if (dev->dev->id.revision < 5) {
+ ring = b43_setup_dmaring(dev, 3, 0, dma64);
+ if (!ring)
+ goto err_destroy_rx0;
+ dma->rx_ring3 = ring;
+ }
+
+ b43dbg(dev->wl, "%d-bit DMA initialized\n",
+ (dmamask == DMA_64BIT_MASK) ? 64 :
+ (dmamask == DMA_32BIT_MASK) ? 32 : 30);
+ err = 0;
+ out:
+ return err;
+
+ err_destroy_rx0:
+ b43_destroy_dmaring(dma->rx_ring0);
+ dma->rx_ring0 = NULL;
+ err_destroy_tx5:
+ b43_destroy_dmaring(dma->tx_ring5);
+ dma->tx_ring5 = NULL;
+ err_destroy_tx4:
+ b43_destroy_dmaring(dma->tx_ring4);
+ dma->tx_ring4 = NULL;
+ err_destroy_tx3:
+ b43_destroy_dmaring(dma->tx_ring3);
+ dma->tx_ring3 = NULL;
+ err_destroy_tx2:
+ b43_destroy_dmaring(dma->tx_ring2);
+ dma->tx_ring2 = NULL;
+ err_destroy_tx1:
+ b43_destroy_dmaring(dma->tx_ring1);
+ dma->tx_ring1 = NULL;
+ err_destroy_tx0:
+ b43_destroy_dmaring(dma->tx_ring0);
+ dma->tx_ring0 = NULL;
+ goto out;
+}
+
+/* Generate a cookie for the TX header. */
+static u16 generate_cookie(struct b43_dmaring *ring, int slot)
+{
+ u16 cookie = 0x1000;
+
+ /* Use the upper 4 bits of the cookie as
+ * DMA controller ID and store the slot number
+ * in the lower 12 bits.
+ * Note that the cookie must never be 0, as this
+ * is a special value used in RX path.
+ */
+ switch (ring->index) {
+ case 0:
+ cookie = 0xA000;
+ break;
+ case 1:
+ cookie = 0xB000;
+ break;
+ case 2:
+ cookie = 0xC000;
+ break;
+ case 3:
+ cookie = 0xD000;
+ break;
+ case 4:
+ cookie = 0xE000;
+ break;
+ case 5:
+ cookie = 0xF000;
+ break;
+ }
+ B43_WARN_ON(slot & ~0x0FFF);
+ cookie |= (u16) slot;
+
+ return cookie;
+}
+
+/* Inspect a cookie and find out to which controller/slot it belongs. */
+static
+struct b43_dmaring *parse_cookie(struct b43_wldev *dev, u16 cookie, int *slot)
+{
+ struct b43_dma *dma = &dev->dma;
+ struct b43_dmaring *ring = NULL;
+
+ switch (cookie & 0xF000) {
+ case 0xA000:
+ ring = dma->tx_ring0;
+ break;
+ case 0xB000:
+ ring = dma->tx_ring1;
+ break;
+ case 0xC000:
+ ring = dma->tx_ring2;
+ break;
+ case 0xD000:
+ ring = dma->tx_ring3;
+ break;
+ case 0xE000:
+ ring = dma->tx_ring4;
+ break;
+ case 0xF000:
+ ring = dma->tx_ring5;
+ break;
+ default:
+ B43_WARN_ON(1);
+ }
+ *slot = (cookie & 0x0FFF);
+ B43_WARN_ON(!(ring && *slot >= 0 && *slot < ring->nr_slots));
+
+ return ring;
+}
+
+static int dma_tx_fragment(struct b43_dmaring *ring,
+ struct sk_buff *skb,
+ struct ieee80211_tx_control *ctl)
+{
+ const struct b43_dma_ops *ops = ring->ops;
+ u8 *header;
+ int slot;
+ int err;
+ struct b43_dmadesc_generic *desc;
+ struct b43_dmadesc_meta *meta;
+ struct b43_dmadesc_meta *meta_hdr;
+ struct sk_buff *bounce_skb;
+
+#define SLOTS_PER_PACKET 2
+ B43_WARN_ON(skb_shinfo(skb)->nr_frags);
+
+ /* Get a slot for the header. */
+ slot = request_slot(ring);
+ desc = ops->idx2desc(ring, slot, &meta_hdr);
+ memset(meta_hdr, 0, sizeof(*meta_hdr));
+
+ header = &(ring->txhdr_cache[slot * sizeof(struct b43_txhdr_fw4)]);
+ b43_generate_txhdr(ring->dev, header,
+ skb->data, skb->len, ctl,
+ generate_cookie(ring, slot));
+
+ meta_hdr->dmaaddr = map_descbuffer(ring, (unsigned char *)header,
+ sizeof(struct b43_txhdr_fw4), 1);
+ if (dma_mapping_error(meta_hdr->dmaaddr))
+ return -EIO;
+ ops->fill_descriptor(ring, desc, meta_hdr->dmaaddr,
+ sizeof(struct b43_txhdr_fw4), 1, 0, 0);
+
+ /* Get a slot for the payload. */
+ slot = request_slot(ring);
+ desc = ops->idx2desc(ring, slot, &meta);
+ memset(meta, 0, sizeof(*meta));
+
+ memcpy(&meta->txstat.control, ctl, sizeof(*ctl));
+ meta->skb = skb;
+ meta->is_last_fragment = 1;
+
+ meta->dmaaddr = map_descbuffer(ring, skb->data, skb->len, 1);
+ /* create a bounce buffer in zone_dma on mapping failure. */
+ if (dma_mapping_error(meta->dmaaddr)) {
+ bounce_skb = __dev_alloc_skb(skb->len, GFP_ATOMIC | GFP_DMA);
+ if (!bounce_skb) {
+ err = -ENOMEM;
+ goto out_unmap_hdr;
+ }
+
+ memcpy(skb_put(bounce_skb, skb->len), skb->data, skb->len);
+ dev_kfree_skb_any(skb);
+ skb = bounce_skb;
+ meta->skb = skb;
+ meta->dmaaddr = map_descbuffer(ring, skb->data, skb->len, 1);
+ if (dma_mapping_error(meta->dmaaddr)) {
+ err = -EIO;
+ goto out_free_bounce;
+ }
+ }
+
+ ops->fill_descriptor(ring, desc, meta->dmaaddr, skb->len, 0, 1, 1);
+
+ /* Now transfer the whole frame. */
+ wmb();
+ ops->poke_tx(ring, next_slot(ring, slot));
+ return 0;
+
+ out_free_bounce:
+ dev_kfree_skb_any(skb);
+ out_unmap_hdr:
+ unmap_descbuffer(ring, meta_hdr->dmaaddr,
+ sizeof(struct b43_txhdr_fw4), 1);
+ return err;
+}
+
+static inline int should_inject_overflow(struct b43_dmaring *ring)
+{
+#ifdef CONFIG_B43_DEBUG
+ if (unlikely(b43_debug(ring->dev, B43_DBG_DMAOVERFLOW))) {
+ /* Check if we should inject another ringbuffer overflow
+ * to test handling of this situation in the stack. */
+ unsigned long next_overflow;
+
+ next_overflow = ring->last_injected_overflow + HZ;
+ if (time_after(jiffies, next_overflow)) {
+ ring->last_injected_overflow = jiffies;
+ b43dbg(ring->dev->wl,
+ "Injecting TX ring overflow on "
+ "DMA controller %d\n", ring->index);
+ return 1;
+ }
+ }
+#endif /* CONFIG_B43_DEBUG */
+ return 0;
+}
+
+int b43_dma_tx(struct b43_wldev *dev,
+ struct sk_buff *skb, struct ieee80211_tx_control *ctl)
+{
+ struct b43_dmaring *ring;
+ int err = 0;
+ unsigned long flags;
+
+ ring = priority_to_txring(dev, ctl->queue);
+ spin_lock_irqsave(&ring->lock, flags);
+ B43_WARN_ON(!ring->tx);
+ if (unlikely(free_slots(ring) < SLOTS_PER_PACKET)) {
+ b43warn(dev->wl, "DMA queue overflow\n");
+ err = -ENOSPC;
+ goto out_unlock;
+ }
+ /* Check if the queue was stopped in mac80211,
+ * but we got called nevertheless.
+ * That would be a mac80211 bug. */
+ B43_WARN_ON(ring->stopped);
+
+ err = dma_tx_fragment(ring, skb, ctl);
+ if (unlikely(err)) {
+ b43err(dev->wl, "DMA tx mapping failure\n");
+ goto out_unlock;
+ }
+ ring->nr_tx_packets++;
+ if ((free_slots(ring) < SLOTS_PER_PACKET) ||
+ should_inject_overflow(ring)) {
+ /* This TX ring is full. */
+ ieee80211_stop_queue(dev->wl->hw, txring_to_priority(ring));
+ ring->stopped = 1;
+ if (b43_debug(dev, B43_DBG_DMAVERBOSE)) {
+ b43dbg(dev->wl, "Stopped TX ring %d\n", ring->index);
+ }
+ }
+ out_unlock:
+ spin_unlock_irqrestore(&ring->lock, flags);
+
+ return err;
+}
+
+void b43_dma_handle_txstatus(struct b43_wldev *dev,
+ const struct b43_txstatus *status)
+{
+ const struct b43_dma_ops *ops;
+ struct b43_dmaring *ring;
+ struct b43_dmadesc_generic *desc;
+ struct b43_dmadesc_meta *meta;
+ int slot;
+
+ ring = parse_cookie(dev, status->cookie, &slot);
+ if (unlikely(!ring))
+ return;
+ B43_WARN_ON(!irqs_disabled());
+ spin_lock(&ring->lock);
+
+ B43_WARN_ON(!ring->tx);
+ ops = ring->ops;
+ while (1) {
+ B43_WARN_ON(!(slot >= 0 && slot < ring->nr_slots));
+ desc = ops->idx2desc(ring, slot, &meta);
+
+ if (meta->skb)
+ unmap_descbuffer(ring, meta->dmaaddr, meta->skb->len,
+ 1);
+ else
+ unmap_descbuffer(ring, meta->dmaaddr,
+ sizeof(struct b43_txhdr_fw4), 1);
+
+ if (meta->is_last_fragment) {
+ B43_WARN_ON(!meta->skb);
+ /* Call back to inform the ieee80211 subsystem about the
+ * status of the transmission.
+ * Some fields of txstat are already filled in dma_tx().
+ */
+ if (status->acked) {
+ meta->txstat.flags |= IEEE80211_TX_STATUS_ACK;
+ } else {
+ if (!(meta->txstat.control.flags
+ & IEEE80211_TXCTL_NO_ACK))
+ meta->txstat.excessive_retries = 1;
+ }
+ if (status->frame_count == 0) {
+ /* The frame was not transmitted at all. */
+ meta->txstat.retry_count = 0;
+ } else
+ meta->txstat.retry_count = status->frame_count - 1;
+ ieee80211_tx_status_irqsafe(dev->wl->hw, meta->skb,
+ &(meta->txstat));
+ /* skb is freed by ieee80211_tx_status_irqsafe() */
+ meta->skb = NULL;
+ } else {
+ /* No need to call free_descriptor_buffer here, as
+ * this is only the txhdr, which is not allocated.
+ */
+ B43_WARN_ON(meta->skb);
+ }
+
+ /* Everything unmapped and free'd. So it's not used anymore. */
+ ring->used_slots--;
+
+ if (meta->is_last_fragment)
+ break;
+ slot = next_slot(ring, slot);
+ }
+ dev->stats.last_tx = jiffies;
+ if (ring->stopped) {
+ B43_WARN_ON(free_slots(ring) < SLOTS_PER_PACKET);
+ ieee80211_wake_queue(dev->wl->hw, txring_to_priority(ring));
+ ring->stopped = 0;
+ if (b43_debug(dev, B43_DBG_DMAVERBOSE)) {
+ b43dbg(dev->wl, "Woke up TX ring %d\n", ring->index);
+ }
+ }
+
+ spin_unlock(&ring->lock);
+}
+
+void b43_dma_get_tx_stats(struct b43_wldev *dev,
+ struct ieee80211_tx_queue_stats *stats)
+{
+ const int nr_queues = dev->wl->hw->queues;
+ struct b43_dmaring *ring;
+ struct ieee80211_tx_queue_stats_data *data;
+ unsigned long flags;
+ int i;
+
+ for (i = 0; i < nr_queues; i++) {
+ data = &(stats->data[i]);
+ ring = priority_to_txring(dev, i);
+
+ spin_lock_irqsave(&ring->lock, flags);
+ data->len = ring->used_slots / SLOTS_PER_PACKET;
+ data->limit = ring->nr_slots / SLOTS_PER_PACKET;
+ data->count = ring->nr_tx_packets;
+ spin_unlock_irqrestore(&ring->lock, flags);
+ }
+}
+
+static void dma_rx(struct b43_dmaring *ring, int *slot)
+{
+ const struct b43_dma_ops *ops = ring->ops;
+ struct b43_dmadesc_generic *desc;
+ struct b43_dmadesc_meta *meta;
+ struct b43_rxhdr_fw4 *rxhdr;
+ struct sk_buff *skb;
+ u16 len;
+ int err;
+ dma_addr_t dmaaddr;
+
+ desc = ops->idx2desc(ring, *slot, &meta);
+
+ sync_descbuffer_for_cpu(ring, meta->dmaaddr, ring->rx_buffersize);
+ skb = meta->skb;
+
+ if (ring->index == 3) {
+ /* We received an xmit status. */
+ struct b43_hwtxstatus *hw = (struct b43_hwtxstatus *)skb->data;
+ int i = 0;
+
+ while (hw->cookie == 0) {
+ if (i > 100)
+ break;
+ i++;
+ udelay(2);
+ barrier();
+ }
+ b43_handle_hwtxstatus(ring->dev, hw);
+ /* recycle the descriptor buffer. */
+ sync_descbuffer_for_device(ring, meta->dmaaddr,
+ ring->rx_buffersize);
+
+ return;
+ }
+ rxhdr = (struct b43_rxhdr_fw4 *)skb->data;
+ len = le16_to_cpu(rxhdr->frame_len);
+ if (len == 0) {
+ int i = 0;
+
+ do {
+ udelay(2);
+ barrier();
+ len = le16_to_cpu(rxhdr->frame_len);
+ } while (len == 0 && i++ < 5);
+ if (unlikely(len == 0)) {
+ /* recycle the descriptor buffer. */
+ sync_descbuffer_for_device(ring, meta->dmaaddr,
+ ring->rx_buffersize);
+ goto drop;
+ }
+ }
+ if (unlikely(len > ring->rx_buffersize)) {
+ /* The data did not fit into one descriptor buffer
+ * and is split over multiple buffers.
+ * This should never happen, as we try to allocate buffers
+ * big enough. So simply ignore this packet.
+ */
+ int cnt = 0;
+ s32 tmp = len;
+
+ while (1) {
+ desc = ops->idx2desc(ring, *slot, &meta);
+ /* recycle the descriptor buffer. */
+ sync_descbuffer_for_device(ring, meta->dmaaddr,
+ ring->rx_buffersize);
+ *slot = next_slot(ring, *slot);
+ cnt++;
+ tmp -= ring->rx_buffersize;
+ if (tmp <= 0)
+ break;
+ }
+ b43err(ring->dev->wl, "DMA RX buffer too small "
+ "(len: %u, buffer: %u, nr-dropped: %d)\n",
+ len, ring->rx_buffersize, cnt);
+ goto drop;
+ }
+
+ dmaaddr = meta->dmaaddr;
+ err = setup_rx_descbuffer(ring, desc, meta, GFP_ATOMIC);
+ if (unlikely(err)) {
+ b43dbg(ring->dev->wl, "DMA RX: setup_rx_descbuffer() failed\n");
+ sync_descbuffer_for_device(ring, dmaaddr, ring->rx_buffersize);
+ goto drop;
+ }
+
+ unmap_descbuffer(ring, dmaaddr, ring->rx_buffersize, 0);
+ skb_put(skb, len + ring->frameoffset);
+ skb_pull(skb, ring->frameoffset);
+
+ b43_rx(ring->dev, skb, rxhdr);
+ drop:
+ return;
+}
+
+void b43_dma_rx(struct b43_dmaring *ring)
+{
+ const struct b43_dma_ops *ops = ring->ops;
+ int slot, current_slot;
+ int used_slots = 0;
+
+ B43_WARN_ON(ring->tx);
+ current_slot = ops->get_current_rxslot(ring);
+ B43_WARN_ON(!(current_slot >= 0 && current_slot < ring->nr_slots));
+
+ slot = ring->current_slot;
+ for (; slot != current_slot; slot = next_slot(ring, slot)) {
+ dma_rx(ring, &slot);
+ update_max_used_slots(ring, ++used_slots);
+ }
+ ops->set_current_rxslot(ring, slot);
+ ring->current_slot = slot;
+}
+
+static void b43_dma_tx_suspend_ring(struct b43_dmaring *ring)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&ring->lock, flags);
+ B43_WARN_ON(!ring->tx);
+ ring->ops->tx_suspend(ring);
+ spin_unlock_irqrestore(&ring->lock, flags);
+}
+
+static void b43_dma_tx_resume_ring(struct b43_dmaring *ring)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&ring->lock, flags);
+ B43_WARN_ON(!ring->tx);
+ ring->ops->tx_resume(ring);
+ spin_unlock_irqrestore(&ring->lock, flags);
+}
+
+void b43_dma_tx_suspend(struct b43_wldev *dev)
+{
+ b43_power_saving_ctl_bits(dev, B43_PS_AWAKE);
+ b43_dma_tx_suspend_ring(dev->dma.tx_ring0);
+ b43_dma_tx_suspend_ring(dev->dma.tx_ring1);
+ b43_dma_tx_suspend_ring(dev->dma.tx_ring2);
+ b43_dma_tx_suspend_ring(dev->dma.tx_ring3);
+ b43_dma_tx_suspend_ring(dev->dma.tx_ring4);
+ b43_dma_tx_suspend_ring(dev->dma.tx_ring5);
+}
+
+void b43_dma_tx_resume(struct b43_wldev *dev)
+{
+ b43_dma_tx_resume_ring(dev->dma.tx_ring5);
+ b43_dma_tx_resume_ring(dev->dma.tx_ring4);
+ b43_dma_tx_resume_ring(dev->dma.tx_ring3);
+ b43_dma_tx_resume_ring(dev->dma.tx_ring2);
+ b43_dma_tx_resume_ring(dev->dma.tx_ring1);
+ b43_dma_tx_resume_ring(dev->dma.tx_ring0);
+ b43_power_saving_ctl_bits(dev, 0);
+}
--- /dev/null
+#ifndef B43_DMA_H_
+#define B43_DMA_H_
+
+#include <linux/list.h>
+#include <linux/spinlock.h>
+#include <linux/workqueue.h>
+#include <linux/linkage.h>
+#include <asm/atomic.h>
+
+#include "b43.h"
+
+/* DMA-Interrupt reasons. */
+#define B43_DMAIRQ_FATALMASK ((1 << 10) | (1 << 11) | (1 << 12) \
+ | (1 << 14) | (1 << 15))
+#define B43_DMAIRQ_NONFATALMASK (1 << 13)
+#define B43_DMAIRQ_RX_DONE (1 << 16)
+
+/*** 32-bit DMA Engine. ***/
+
+/* 32-bit DMA controller registers. */
+#define B43_DMA32_TXCTL 0x00
+#define B43_DMA32_TXENABLE 0x00000001
+#define B43_DMA32_TXSUSPEND 0x00000002
+#define B43_DMA32_TXLOOPBACK 0x00000004
+#define B43_DMA32_TXFLUSH 0x00000010
+#define B43_DMA32_TXADDREXT_MASK 0x00030000
+#define B43_DMA32_TXADDREXT_SHIFT 16
+#define B43_DMA32_TXRING 0x04
+#define B43_DMA32_TXINDEX 0x08
+#define B43_DMA32_TXSTATUS 0x0C
+#define B43_DMA32_TXDPTR 0x00000FFF
+#define B43_DMA32_TXSTATE 0x0000F000
+#define B43_DMA32_TXSTAT_DISABLED 0x00000000
+#define B43_DMA32_TXSTAT_ACTIVE 0x00001000
+#define B43_DMA32_TXSTAT_IDLEWAIT 0x00002000
+#define B43_DMA32_TXSTAT_STOPPED 0x00003000
+#define B43_DMA32_TXSTAT_SUSP 0x00004000
+#define B43_DMA32_TXERROR 0x000F0000
+#define B43_DMA32_TXERR_NOERR 0x00000000
+#define B43_DMA32_TXERR_PROT 0x00010000
+#define B43_DMA32_TXERR_UNDERRUN 0x00020000
+#define B43_DMA32_TXERR_BUFREAD 0x00030000
+#define B43_DMA32_TXERR_DESCREAD 0x00040000
+#define B43_DMA32_TXACTIVE 0xFFF00000
+#define B43_DMA32_RXCTL 0x10
+#define B43_DMA32_RXENABLE 0x00000001
+#define B43_DMA32_RXFROFF_MASK 0x000000FE
+#define B43_DMA32_RXFROFF_SHIFT 1
+#define B43_DMA32_RXDIRECTFIFO 0x00000100
+#define B43_DMA32_RXADDREXT_MASK 0x00030000
+#define B43_DMA32_RXADDREXT_SHIFT 16
+#define B43_DMA32_RXRING 0x14
+#define B43_DMA32_RXINDEX 0x18
+#define B43_DMA32_RXSTATUS 0x1C
+#define B43_DMA32_RXDPTR 0x00000FFF
+#define B43_DMA32_RXSTATE 0x0000F000
+#define B43_DMA32_RXSTAT_DISABLED 0x00000000
+#define B43_DMA32_RXSTAT_ACTIVE 0x00001000
+#define B43_DMA32_RXSTAT_IDLEWAIT 0x00002000
+#define B43_DMA32_RXSTAT_STOPPED 0x00003000
+#define B43_DMA32_RXERROR 0x000F0000
+#define B43_DMA32_RXERR_NOERR 0x00000000
+#define B43_DMA32_RXERR_PROT 0x00010000
+#define B43_DMA32_RXERR_OVERFLOW 0x00020000
+#define B43_DMA32_RXERR_BUFWRITE 0x00030000
+#define B43_DMA32_RXERR_DESCREAD 0x00040000
+#define B43_DMA32_RXACTIVE 0xFFF00000
+
+/* 32-bit DMA descriptor. */
+struct b43_dmadesc32 {
+ __le32 control;
+ __le32 address;
+} __attribute__ ((__packed__));
+#define B43_DMA32_DCTL_BYTECNT 0x00001FFF
+#define B43_DMA32_DCTL_ADDREXT_MASK 0x00030000
+#define B43_DMA32_DCTL_ADDREXT_SHIFT 16
+#define B43_DMA32_DCTL_DTABLEEND 0x10000000
+#define B43_DMA32_DCTL_IRQ 0x20000000
+#define B43_DMA32_DCTL_FRAMEEND 0x40000000
+#define B43_DMA32_DCTL_FRAMESTART 0x80000000
+
+/*** 64-bit DMA Engine. ***/
+
+/* 64-bit DMA controller registers. */
+#define B43_DMA64_TXCTL 0x00
+#define B43_DMA64_TXENABLE 0x00000001
+#define B43_DMA64_TXSUSPEND 0x00000002
+#define B43_DMA64_TXLOOPBACK 0x00000004
+#define B43_DMA64_TXFLUSH 0x00000010
+#define B43_DMA64_TXADDREXT_MASK 0x00030000
+#define B43_DMA64_TXADDREXT_SHIFT 16
+#define B43_DMA64_TXINDEX 0x04
+#define B43_DMA64_TXRINGLO 0x08
+#define B43_DMA64_TXRINGHI 0x0C
+#define B43_DMA64_TXSTATUS 0x10
+#define B43_DMA64_TXSTATDPTR 0x00001FFF
+#define B43_DMA64_TXSTAT 0xF0000000
+#define B43_DMA64_TXSTAT_DISABLED 0x00000000
+#define B43_DMA64_TXSTAT_ACTIVE 0x10000000
+#define B43_DMA64_TXSTAT_IDLEWAIT 0x20000000
+#define B43_DMA64_TXSTAT_STOPPED 0x30000000
+#define B43_DMA64_TXSTAT_SUSP 0x40000000
+#define B43_DMA64_TXERROR 0x14
+#define B43_DMA64_TXERRDPTR 0x0001FFFF
+#define B43_DMA64_TXERR 0xF0000000
+#define B43_DMA64_TXERR_NOERR 0x00000000
+#define B43_DMA64_TXERR_PROT 0x10000000
+#define B43_DMA64_TXERR_UNDERRUN 0x20000000
+#define B43_DMA64_TXERR_TRANSFER 0x30000000
+#define B43_DMA64_TXERR_DESCREAD 0x40000000
+#define B43_DMA64_TXERR_CORE 0x50000000
+#define B43_DMA64_RXCTL 0x20
+#define B43_DMA64_RXENABLE 0x00000001
+#define B43_DMA64_RXFROFF_MASK 0x000000FE
+#define B43_DMA64_RXFROFF_SHIFT 1
+#define B43_DMA64_RXDIRECTFIFO 0x00000100
+#define B43_DMA64_RXADDREXT_MASK 0x00030000
+#define B43_DMA64_RXADDREXT_SHIFT 16
+#define B43_DMA64_RXINDEX 0x24
+#define B43_DMA64_RXRINGLO 0x28
+#define B43_DMA64_RXRINGHI 0x2C
+#define B43_DMA64_RXSTATUS 0x30
+#define B43_DMA64_RXSTATDPTR 0x00001FFF
+#define B43_DMA64_RXSTAT 0xF0000000
+#define B43_DMA64_RXSTAT_DISABLED 0x00000000
+#define B43_DMA64_RXSTAT_ACTIVE 0x10000000
+#define B43_DMA64_RXSTAT_IDLEWAIT 0x20000000
+#define B43_DMA64_RXSTAT_STOPPED 0x30000000
+#define B43_DMA64_RXSTAT_SUSP 0x40000000
+#define B43_DMA64_RXERROR 0x34
+#define B43_DMA64_RXERRDPTR 0x0001FFFF
+#define B43_DMA64_RXERR 0xF0000000
+#define B43_DMA64_RXERR_NOERR 0x00000000
+#define B43_DMA64_RXERR_PROT 0x10000000
+#define B43_DMA64_RXERR_UNDERRUN 0x20000000
+#define B43_DMA64_RXERR_TRANSFER 0x30000000
+#define B43_DMA64_RXERR_DESCREAD 0x40000000
+#define B43_DMA64_RXERR_CORE 0x50000000
+
+/* 64-bit DMA descriptor. */
+struct b43_dmadesc64 {
+ __le32 control0;
+ __le32 control1;
+ __le32 address_low;
+ __le32 address_high;
+} __attribute__ ((__packed__));
+#define B43_DMA64_DCTL0_DTABLEEND 0x10000000
+#define B43_DMA64_DCTL0_IRQ 0x20000000
+#define B43_DMA64_DCTL0_FRAMEEND 0x40000000
+#define B43_DMA64_DCTL0_FRAMESTART 0x80000000
+#define B43_DMA64_DCTL1_BYTECNT 0x00001FFF
+#define B43_DMA64_DCTL1_ADDREXT_MASK 0x00030000
+#define B43_DMA64_DCTL1_ADDREXT_SHIFT 16
+
+struct b43_dmadesc_generic {
+ union {
+ struct b43_dmadesc32 dma32;
+ struct b43_dmadesc64 dma64;
+ } __attribute__ ((__packed__));
+} __attribute__ ((__packed__));
+
+/* Misc DMA constants */
+#define B43_DMA_RINGMEMSIZE PAGE_SIZE
+#define B43_DMA0_RX_FRAMEOFFSET 30
+#define B43_DMA3_RX_FRAMEOFFSET 0
+
+/* DMA engine tuning knobs */
+#define B43_TXRING_SLOTS 128
+#define B43_RXRING_SLOTS 64
+#define B43_DMA0_RX_BUFFERSIZE (2304 + 100)
+#define B43_DMA3_RX_BUFFERSIZE 16
+
+#ifdef CONFIG_B43_DMA
+
+struct sk_buff;
+struct b43_private;
+struct b43_txstatus;
+
+struct b43_dmadesc_meta {
+ /* The kernel DMA-able buffer. */
+ struct sk_buff *skb;
+ /* DMA base bus-address of the descriptor buffer. */
+ dma_addr_t dmaaddr;
+ /* ieee80211 TX status. Only used once per 802.11 frag. */
+ bool is_last_fragment;
+ struct ieee80211_tx_status txstat;
+};
+
+struct b43_dmaring;
+
+/* Lowlevel DMA operations that differ between 32bit and 64bit DMA. */
+struct b43_dma_ops {
+ struct b43_dmadesc_generic *(*idx2desc) (struct b43_dmaring * ring,
+ int slot,
+ struct b43_dmadesc_meta **
+ meta);
+ void (*fill_descriptor) (struct b43_dmaring * ring,
+ struct b43_dmadesc_generic * desc,
+ dma_addr_t dmaaddr, u16 bufsize, int start,
+ int end, int irq);
+ void (*poke_tx) (struct b43_dmaring * ring, int slot);
+ void (*tx_suspend) (struct b43_dmaring * ring);
+ void (*tx_resume) (struct b43_dmaring * ring);
+ int (*get_current_rxslot) (struct b43_dmaring * ring);
+ void (*set_current_rxslot) (struct b43_dmaring * ring, int slot);
+};
+
+struct b43_dmaring {
+ /* Lowlevel DMA ops. */
+ const struct b43_dma_ops *ops;
+ /* Kernel virtual base address of the ring memory. */
+ void *descbase;
+ /* Meta data about all descriptors. */
+ struct b43_dmadesc_meta *meta;
+ /* Cache of TX headers for each slot.
+ * This is to avoid an allocation on each TX.
+ * This is NULL for an RX ring.
+ */
+ u8 *txhdr_cache;
+ /* (Unadjusted) DMA base bus-address of the ring memory. */
+ dma_addr_t dmabase;
+ /* Number of descriptor slots in the ring. */
+ int nr_slots;
+ /* Number of used descriptor slots. */
+ int used_slots;
+ /* Currently used slot in the ring. */
+ int current_slot;
+ /* Total number of packets sent. Statistics only. */
+ unsigned int nr_tx_packets;
+ /* Frameoffset in octets. */
+ u32 frameoffset;
+ /* Descriptor buffer size. */
+ u16 rx_buffersize;
+ /* The MMIO base register of the DMA controller. */
+ u16 mmio_base;
+ /* DMA controller index number (0-5). */
+ int index;
+ /* Boolean. Is this a TX ring? */
+ bool tx;
+ /* Boolean. 64bit DMA if true, 32bit DMA otherwise. */
+ bool dma64;
+ /* Boolean. Is this ring stopped at ieee80211 level? */
+ bool stopped;
+ /* Lock, only used for TX. */
+ spinlock_t lock;
+ struct b43_wldev *dev;
+#ifdef CONFIG_B43_DEBUG
+ /* Maximum number of used slots. */
+ int max_used_slots;
+ /* Last time we injected a ring overflow. */
+ unsigned long last_injected_overflow;
+#endif /* CONFIG_B43_DEBUG */
+};
+
+static inline u32 b43_dma_read(struct b43_dmaring *ring, u16 offset)
+{
+ return b43_read32(ring->dev, ring->mmio_base + offset);
+}
+
+static inline
+ void b43_dma_write(struct b43_dmaring *ring, u16 offset, u32 value)
+{
+ b43_write32(ring->dev, ring->mmio_base + offset, value);
+}
+
+int b43_dma_init(struct b43_wldev *dev);
+void b43_dma_free(struct b43_wldev *dev);
+
+int b43_dmacontroller_rx_reset(struct b43_wldev *dev,
+ u16 dmacontroller_mmio_base, int dma64);
+int b43_dmacontroller_tx_reset(struct b43_wldev *dev,
+ u16 dmacontroller_mmio_base, int dma64);
+
+u16 b43_dmacontroller_base(int dma64bit, int dmacontroller_idx);
+
+void b43_dma_tx_suspend(struct b43_wldev *dev);
+void b43_dma_tx_resume(struct b43_wldev *dev);
+
+void b43_dma_get_tx_stats(struct b43_wldev *dev,
+ struct ieee80211_tx_queue_stats *stats);
+
+int b43_dma_tx(struct b43_wldev *dev,
+ struct sk_buff *skb, struct ieee80211_tx_control *ctl);
+void b43_dma_handle_txstatus(struct b43_wldev *dev,
+ const struct b43_txstatus *status);
+
+void b43_dma_rx(struct b43_dmaring *ring);
+
+#else /* CONFIG_B43_DMA */
+
+static inline int b43_dma_init(struct b43_wldev *dev)
+{
+ return 0;
+}
+static inline void b43_dma_free(struct b43_wldev *dev)
+{
+}
+static inline
+ int b43_dmacontroller_rx_reset(struct b43_wldev *dev,
+ u16 dmacontroller_mmio_base, int dma64)
+{
+ return 0;
+}
+static inline
+ int b43_dmacontroller_tx_reset(struct b43_wldev *dev,
+ u16 dmacontroller_mmio_base, int dma64)
+{
+ return 0;
+}
+static inline
+ void b43_dma_get_tx_stats(struct b43_wldev *dev,
+ struct ieee80211_tx_queue_stats *stats)
+{
+}
+static inline
+ int b43_dma_tx(struct b43_wldev *dev,
+ struct sk_buff *skb, struct ieee80211_tx_control *ctl)
+{
+ return 0;
+}
+static inline
+ void b43_dma_handle_txstatus(struct b43_wldev *dev,
+ const struct b43_txstatus *status)
+{
+}
+static inline void b43_dma_rx(struct b43_dmaring *ring)
+{
+}
+static inline void b43_dma_tx_suspend(struct b43_wldev *dev)
+{
+}
+static inline void b43_dma_tx_resume(struct b43_wldev *dev)
+{
+}
+
+#endif /* CONFIG_B43_DMA */
+#endif /* B43_DMA_H_ */
--- /dev/null
+/*
+
+ Broadcom B43 wireless driver
+
+ Copyright (c) 2005 Martin Langer <martin-langer@gmx.de>,
+ Stefano Brivio <st3@riseup.net>
+ Michael Buesch <mb@bu3sch.de>
+ Danny van Dyk <kugelfang@gentoo.org>
+ Andreas Jaggi <andreas.jaggi@waterwave.ch>
+
+ This program is free software; you can redistribute it and/or modify
+ it under the terms of the GNU General Public License as published by
+ the Free Software Foundation; either version 2 of the License, or
+ (at your option) any later version.
+
+ This program is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ GNU General Public License for more details.
+
+ You should have received a copy of the GNU General Public License
+ along with this program; see the file COPYING. If not, write to
+ the Free Software Foundation, Inc., 51 Franklin Steet, Fifth Floor,
+ Boston, MA 02110-1301, USA.
+
+*/
+
+#include "b43.h"
+#include "leds.h"
+#include "main.h"
+
+static void b43_led_changestate(struct b43_led *led)
+{
+ struct b43_wldev *dev = led->dev;
+ const int index = b43_led_index(led);
+ const u16 mask = (1 << index);
+ u16 ledctl;
+
+ B43_WARN_ON(!(index >= 0 && index < B43_NR_LEDS));
+ B43_WARN_ON(!led->blink_interval);
+ ledctl = b43_read16(dev, B43_MMIO_GPIO_CONTROL);
+ ledctl = (ledctl & mask) ? (ledctl & ~mask) : (ledctl | mask);
+ b43_write16(dev, B43_MMIO_GPIO_CONTROL, ledctl);
+}
+
+static void b43_led_blink(unsigned long d)
+{
+ struct b43_led *led = (struct b43_led *)d;
+ struct b43_wldev *dev = led->dev;
+ unsigned long flags;
+
+ spin_lock_irqsave(&dev->wl->leds_lock, flags);
+ if (led->blink_interval) {
+ b43_led_changestate(led);
+ mod_timer(&led->blink_timer, jiffies + led->blink_interval);
+ }
+ spin_unlock_irqrestore(&dev->wl->leds_lock, flags);
+}
+
+static void b43_led_blink_start(struct b43_led *led, unsigned long interval)
+{
+ if (led->blink_interval)
+ return;
+ led->blink_interval = interval;
+ b43_led_changestate(led);
+ led->blink_timer.expires = jiffies + interval;
+ add_timer(&led->blink_timer);
+}
+
+static void b43_led_blink_stop(struct b43_led *led, int sync)
+{
+ struct b43_wldev *dev = led->dev;
+ const int index = b43_led_index(led);
+ u16 ledctl;
+
+ if (!led->blink_interval)
+ return;
+ if (unlikely(sync))
+ del_timer_sync(&led->blink_timer);
+ else
+ del_timer(&led->blink_timer);
+ led->blink_interval = 0;
+
+ /* Make sure the LED is turned off. */
+ B43_WARN_ON(!(index >= 0 && index < B43_NR_LEDS));
+ ledctl = b43_read16(dev, B43_MMIO_GPIO_CONTROL);
+ if (led->activelow)
+ ledctl |= (1 << index);
+ else
+ ledctl &= ~(1 << index);
+ b43_write16(dev, B43_MMIO_GPIO_CONTROL, ledctl);
+}
+
+static void b43_led_init_hardcoded(struct b43_wldev *dev,
+ struct b43_led *led, int led_index)
+{
+ struct ssb_bus *bus = dev->dev->bus;
+
+ /* This function is called, if the behaviour (and activelow)
+ * information for a LED is missing in the SPROM.
+ * We hardcode the behaviour values for various devices here.
+ * Note that the B43_LED_TEST_XXX behaviour values can
+ * be used to figure out which led is mapped to which index.
+ */
+
+ switch (led_index) {
+ case 0:
+ led->behaviour = B43_LED_ACTIVITY;
+ led->activelow = 1;
+ if (bus->boardinfo.vendor == PCI_VENDOR_ID_COMPAQ)
+ led->behaviour = B43_LED_RADIO_ALL;
+ break;
+ case 1:
+ led->behaviour = B43_LED_RADIO_B;
+ if (bus->boardinfo.vendor == PCI_VENDOR_ID_ASUSTEK)
+ led->behaviour = B43_LED_ASSOC;
+ break;
+ case 2:
+ led->behaviour = B43_LED_RADIO_A;
+ break;
+ case 3:
+ led->behaviour = B43_LED_OFF;
+ break;
+ default:
+ B43_WARN_ON(1);
+ }
+}
+
+int b43_leds_init(struct b43_wldev *dev)
+{
+ struct b43_led *led;
+ u8 sprom[4];
+ int i;
+
+ sprom[0] = dev->dev->bus->sprom.r1.gpio0;
+ sprom[1] = dev->dev->bus->sprom.r1.gpio1;
+ sprom[2] = dev->dev->bus->sprom.r1.gpio2;
+ sprom[3] = dev->dev->bus->sprom.r1.gpio3;
+
+ for (i = 0; i < B43_NR_LEDS; i++) {
+ led = &(dev->leds[i]);
+ led->dev = dev;
+ setup_timer(&led->blink_timer,
+ b43_led_blink, (unsigned long)led);
+
+ if (sprom[i] == 0xFF) {
+ b43_led_init_hardcoded(dev, led, i);
+ } else {
+ led->behaviour = sprom[i] & B43_LED_BEHAVIOUR;
+ led->activelow = !!(sprom[i] & B43_LED_ACTIVELOW);
+ }
+ }
+
+ return 0;
+}
+
+void b43_leds_exit(struct b43_wldev *dev)
+{
+ struct b43_led *led;
+ int i;
+
+ for (i = 0; i < B43_NR_LEDS; i++) {
+ led = &(dev->leds[i]);
+ b43_led_blink_stop(led, 1);
+ }
+ b43_leds_switch_all(dev, 0);
+}
+
+void b43_leds_update(struct b43_wldev *dev, int activity)
+{
+ struct b43_led *led;
+ struct b43_phy *phy = &dev->phy;
+ const int transferring =
+ (jiffies - dev->stats.last_tx) < B43_LED_XFER_THRES;
+ int i, turn_on;
+ unsigned long interval = 0;
+ u16 ledctl;
+ unsigned long flags;
+
+ spin_lock_irqsave(&dev->wl->leds_lock, flags);
+ ledctl = b43_read16(dev, B43_MMIO_GPIO_CONTROL);
+ for (i = 0; i < B43_NR_LEDS; i++) {
+ led = &(dev->leds[i]);
+
+ turn_on = 0;
+ switch (led->behaviour) {
+ case B43_LED_INACTIVE:
+ continue;
+ case B43_LED_OFF:
+ break;
+ case B43_LED_ON:
+ turn_on = 1;
+ break;
+ case B43_LED_ACTIVITY:
+ turn_on = activity;
+ break;
+ case B43_LED_RADIO_ALL:
+ turn_on = phy->radio_on && b43_is_hw_radio_enabled(dev);
+ break;
+ case B43_LED_RADIO_A:
+ turn_on = (phy->radio_on && b43_is_hw_radio_enabled(dev)
+ && phy->type == B43_PHYTYPE_A);
+ break;
+ case B43_LED_RADIO_B:
+ turn_on = (phy->radio_on && b43_is_hw_radio_enabled(dev)
+ && (phy->type == B43_PHYTYPE_B
+ || phy->type == B43_PHYTYPE_G));
+ break;
+ case B43_LED_MODE_BG:
+ if (phy->type == B43_PHYTYPE_G
+ && b43_is_hw_radio_enabled(dev)
+ && 1 /*FIXME: using G rates. */ )
+ turn_on = 1;
+ break;
+ case B43_LED_TRANSFER:
+ if (transferring)
+ b43_led_blink_start(led, B43_LEDBLINK_MEDIUM);
+ else
+ b43_led_blink_stop(led, 0);
+ continue;
+ case B43_LED_APTRANSFER:
+ if (b43_is_mode(dev->wl, IEEE80211_IF_TYPE_AP)) {
+ if (transferring) {
+ interval = B43_LEDBLINK_FAST;
+ turn_on = 1;
+ }
+ } else {
+ turn_on = 1;
+ if (0 /*TODO: not assoc */ )
+ interval = B43_LEDBLINK_SLOW;
+ else if (transferring)
+ interval = B43_LEDBLINK_FAST;
+ else
+ turn_on = 0;
+ }
+ if (turn_on)
+ b43_led_blink_start(led, interval);
+ else
+ b43_led_blink_stop(led, 0);
+ continue;
+ case B43_LED_WEIRD:
+ //TODO
+ break;
+ case B43_LED_ASSOC:
+ if (1 /*dev->softmac->associated */ )
+ turn_on = 1;
+ break;
+#ifdef CONFIG_B43_DEBUG
+ case B43_LED_TEST_BLINKSLOW:
+ b43_led_blink_start(led, B43_LEDBLINK_SLOW);
+ continue;
+ case B43_LED_TEST_BLINKMEDIUM:
+ b43_led_blink_start(led, B43_LEDBLINK_MEDIUM);
+ continue;
+ case B43_LED_TEST_BLINKFAST:
+ b43_led_blink_start(led, B43_LEDBLINK_FAST);
+ continue;
+#endif /* CONFIG_B43_DEBUG */
+ default:
+ B43_WARN_ON(1);
+ };
+
+ if (led->activelow)
+ turn_on = !turn_on;
+ if (turn_on)
+ ledctl |= (1 << i);
+ else
+ ledctl &= ~(1 << i);
+ }
+ b43_write16(dev, B43_MMIO_GPIO_CONTROL, ledctl);
+ spin_unlock_irqrestore(&dev->wl->leds_lock, flags);
+}
+
+void b43_leds_switch_all(struct b43_wldev *dev, int on)
+{
+ struct b43_led *led;
+ u16 ledctl;
+ int i;
+ int bit_on;
+ unsigned long flags;
+
+ spin_lock_irqsave(&dev->wl->leds_lock, flags);
+ ledctl = b43_read16(dev, B43_MMIO_GPIO_CONTROL);
+ for (i = 0; i < B43_NR_LEDS; i++) {
+ led = &(dev->leds[i]);
+ if (led->behaviour == B43_LED_INACTIVE)
+ continue;
+ if (on)
+ bit_on = led->activelow ? 0 : 1;
+ else
+ bit_on = led->activelow ? 1 : 0;
+ if (bit_on)
+ ledctl |= (1 << i);
+ else
+ ledctl &= ~(1 << i);
+ }
+ b43_write16(dev, B43_MMIO_GPIO_CONTROL, ledctl);
+ spin_unlock_irqrestore(&dev->wl->leds_lock, flags);
+}
--- /dev/null
+#ifndef B43_LEDS_H_
+#define B43_LEDS_H_
+
+#include <linux/types.h>
+#include <linux/timer.h>
+
+struct b43_led {
+ u8 behaviour:7;
+ u8 activelow:1;
+
+ struct b43_wldev *dev;
+ struct timer_list blink_timer;
+ unsigned long blink_interval;
+};
+#define b43_led_index(led) ((int)((led) - (led)->dev->leds))
+
+/* Delay between state changes when blinking in jiffies */
+#define B43_LEDBLINK_SLOW (HZ / 1)
+#define B43_LEDBLINK_MEDIUM (HZ / 4)
+#define B43_LEDBLINK_FAST (HZ / 8)
+
+#define B43_LED_XFER_THRES (HZ / 100)
+
+#define B43_LED_BEHAVIOUR 0x7F
+#define B43_LED_ACTIVELOW 0x80
+enum { /* LED behaviour values */
+ B43_LED_OFF,
+ B43_LED_ON,
+ B43_LED_ACTIVITY,
+ B43_LED_RADIO_ALL,
+ B43_LED_RADIO_A,
+ B43_LED_RADIO_B,
+ B43_LED_MODE_BG,
+ B43_LED_TRANSFER,
+ B43_LED_APTRANSFER,
+ B43_LED_WEIRD, //FIXME
+ B43_LED_ASSOC,
+ B43_LED_INACTIVE,
+
+ /* Behaviour values for testing.
+ * With these values it is easier to figure out
+ * the real behaviour of leds, in case the SPROM
+ * is missing information.
+ */
+ B43_LED_TEST_BLINKSLOW,
+ B43_LED_TEST_BLINKMEDIUM,
+ B43_LED_TEST_BLINKFAST,
+};
+
+int b43_leds_init(struct b43_wldev *dev);
+void b43_leds_exit(struct b43_wldev *dev);
+void b43_leds_update(struct b43_wldev *dev, int activity);
+void b43_leds_switch_all(struct b43_wldev *dev, int on);
+
+#endif /* B43_LEDS_H_ */
--- /dev/null
+/*
+
+ Broadcom B43 wireless driver
+
+ G PHY LO (LocalOscillator) Measuring and Control routines
+
+ Copyright (c) 2005 Martin Langer <martin-langer@gmx.de>,
+ Copyright (c) 2005, 2006 Stefano Brivio <st3@riseup.net>
+ Copyright (c) 2005-2007 Michael Buesch <mb@bu3sch.de>
+ Copyright (c) 2005, 2006 Danny van Dyk <kugelfang@gentoo.org>
+ Copyright (c) 2005, 2006 Andreas Jaggi <andreas.jaggi@waterwave.ch>
+
+ This program is free software; you can redistribute it and/or modify
+ it under the terms of the GNU General Public License as published by
+ the Free Software Foundation; either version 2 of the License, or
+ (at your option) any later version.
+
+ This program is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ GNU General Public License for more details.
+
+ You should have received a copy of the GNU General Public License
+ along with this program; see the file COPYING. If not, write to
+ the Free Software Foundation, Inc., 51 Franklin Steet, Fifth Floor,
+ Boston, MA 02110-1301, USA.
+
+*/
+
+#include "b43.h"
+#include "lo.h"
+#include "phy.h"
+#include "main.h"
+
+#include <linux/delay.h>
+#include <linux/sched.h>
+
+
+/* Define to 1 to always calibrate all possible LO control pairs.
+ * This is a workaround until we fix the partial LO calibration optimization. */
+#define B43_CALIB_ALL_LOCTLS 1
+
+
+/* Write the LocalOscillator Control (adjust) value-pair. */
+static void b43_lo_write(struct b43_wldev *dev, struct b43_loctl *control)
+{
+ struct b43_phy *phy = &dev->phy;
+ u16 value;
+ u16 reg;
+
+ if (B43_DEBUG) {
+ if (unlikely(abs(control->i) > 16 || abs(control->q) > 16)) {
+ b43dbg(dev->wl, "Invalid LO control pair "
+ "(I: %d, Q: %d)\n", control->i, control->q);
+ dump_stack();
+ return;
+ }
+ }
+
+ value = (u8) (control->q);
+ value |= ((u8) (control->i)) << 8;
+
+ reg = (phy->type == B43_PHYTYPE_B) ? 0x002F : B43_PHY_LO_CTL;
+ b43_phy_write(dev, reg, value);
+}
+
+static int assert_rfatt_and_bbatt(const struct b43_rfatt *rfatt,
+ const struct b43_bbatt *bbatt,
+ struct b43_wldev *dev)
+{
+ int err = 0;
+
+ /* Check the attenuation values against the LO control array sizes. */
+ if (unlikely(rfatt->att >= B43_NR_RF)) {
+ b43err(dev->wl, "rfatt(%u) >= size of LO array\n", rfatt->att);
+ err = -EINVAL;
+ }
+ if (unlikely(bbatt->att >= B43_NR_BB)) {
+ b43err(dev->wl, "bbatt(%u) >= size of LO array\n", bbatt->att);
+ err = -EINVAL;
+ }
+
+ return err;
+}
+
+#if !B43_CALIB_ALL_LOCTLS
+static
+struct b43_loctl *b43_get_lo_g_ctl_nopadmix(struct b43_wldev *dev,
+ const struct b43_rfatt *rfatt,
+ const struct b43_bbatt *bbatt)
+{
+ struct b43_phy *phy = &dev->phy;
+ struct b43_txpower_lo_control *lo = phy->lo_control;
+
+ if (assert_rfatt_and_bbatt(rfatt, bbatt, dev))
+ return &(lo->no_padmix[0][0]); /* Just prevent a crash */
+ return &(lo->no_padmix[bbatt->att][rfatt->att]);
+}
+#endif /* !B43_CALIB_ALL_LOCTLS */
+
+struct b43_loctl *b43_get_lo_g_ctl(struct b43_wldev *dev,
+ const struct b43_rfatt *rfatt,
+ const struct b43_bbatt *bbatt)
+{
+ struct b43_phy *phy = &dev->phy;
+ struct b43_txpower_lo_control *lo = phy->lo_control;
+
+ if (assert_rfatt_and_bbatt(rfatt, bbatt, dev))
+ return &(lo->no_padmix[0][0]); /* Just prevent a crash */
+ if (rfatt->with_padmix)
+ return &(lo->with_padmix[bbatt->att][rfatt->att]);
+ return &(lo->no_padmix[bbatt->att][rfatt->att]);
+}
+
+/* Call a function for every possible LO control value-pair. */
+static void b43_call_for_each_loctl(struct b43_wldev *dev,
+ void (*func) (struct b43_wldev *,
+ struct b43_loctl *))
+{
+ struct b43_phy *phy = &dev->phy;
+ struct b43_txpower_lo_control *ctl = phy->lo_control;
+ int i, j;
+
+ for (i = 0; i < B43_NR_BB; i++) {
+ for (j = 0; j < B43_NR_RF; j++)
+ func(dev, &(ctl->with_padmix[i][j]));
+ }
+ for (i = 0; i < B43_NR_BB; i++) {
+ for (j = 0; j < B43_NR_RF; j++)
+ func(dev, &(ctl->no_padmix[i][j]));
+ }
+}
+
+static u16 lo_b_r15_loop(struct b43_wldev *dev)
+{
+ int i;
+ u16 ret = 0;
+
+ for (i = 0; i < 10; i++) {
+ b43_phy_write(dev, 0x0015, 0xAFA0);
+ udelay(1);
+ b43_phy_write(dev, 0x0015, 0xEFA0);
+ udelay(10);
+ b43_phy_write(dev, 0x0015, 0xFFA0);
+ udelay(40);
+ ret += b43_phy_read(dev, 0x002C);
+ }
+
+ return ret;
+}
+
+void b43_lo_b_measure(struct b43_wldev *dev)
+{
+ struct b43_phy *phy = &dev->phy;
+ u16 regstack[12] = { 0 };
+ u16 mls;
+ u16 fval;
+ int i, j;
+
+ regstack[0] = b43_phy_read(dev, 0x0015);
+ regstack[1] = b43_radio_read16(dev, 0x0052) & 0xFFF0;
+
+ if (phy->radio_ver == 0x2053) {
+ regstack[2] = b43_phy_read(dev, 0x000A);
+ regstack[3] = b43_phy_read(dev, 0x002A);
+ regstack[4] = b43_phy_read(dev, 0x0035);
+ regstack[5] = b43_phy_read(dev, 0x0003);
+ regstack[6] = b43_phy_read(dev, 0x0001);
+ regstack[7] = b43_phy_read(dev, 0x0030);
+
+ regstack[8] = b43_radio_read16(dev, 0x0043);
+ regstack[9] = b43_radio_read16(dev, 0x007A);
+ regstack[10] = b43_read16(dev, 0x03EC);
+ regstack[11] = b43_radio_read16(dev, 0x0052) & 0x00F0;
+
+ b43_phy_write(dev, 0x0030, 0x00FF);
+ b43_write16(dev, 0x03EC, 0x3F3F);
+ b43_phy_write(dev, 0x0035, regstack[4] & 0xFF7F);
+ b43_radio_write16(dev, 0x007A, regstack[9] & 0xFFF0);
+ }
+ b43_phy_write(dev, 0x0015, 0xB000);
+ b43_phy_write(dev, 0x002B, 0x0004);
+
+ if (phy->radio_ver == 0x2053) {
+ b43_phy_write(dev, 0x002B, 0x0203);
+ b43_phy_write(dev, 0x002A, 0x08A3);
+ }
+
+ phy->minlowsig[0] = 0xFFFF;
+
+ for (i = 0; i < 4; i++) {
+ b43_radio_write16(dev, 0x0052, regstack[1] | i);
+ lo_b_r15_loop(dev);
+ }
+ for (i = 0; i < 10; i++) {
+ b43_radio_write16(dev, 0x0052, regstack[1] | i);
+ mls = lo_b_r15_loop(dev) / 10;
+ if (mls < phy->minlowsig[0]) {
+ phy->minlowsig[0] = mls;
+ phy->minlowsigpos[0] = i;
+ }
+ }
+ b43_radio_write16(dev, 0x0052, regstack[1] | phy->minlowsigpos[0]);
+
+ phy->minlowsig[1] = 0xFFFF;
+
+ for (i = -4; i < 5; i += 2) {
+ for (j = -4; j < 5; j += 2) {
+ if (j < 0)
+ fval = (0x0100 * i) + j + 0x0100;
+ else
+ fval = (0x0100 * i) + j;
+ b43_phy_write(dev, 0x002F, fval);
+ mls = lo_b_r15_loop(dev) / 10;
+ if (mls < phy->minlowsig[1]) {
+ phy->minlowsig[1] = mls;
+ phy->minlowsigpos[1] = fval;
+ }
+ }
+ }
+ phy->minlowsigpos[1] += 0x0101;
+
+ b43_phy_write(dev, 0x002F, phy->minlowsigpos[1]);
+ if (phy->radio_ver == 0x2053) {
+ b43_phy_write(dev, 0x000A, regstack[2]);
+ b43_phy_write(dev, 0x002A, regstack[3]);
+ b43_phy_write(dev, 0x0035, regstack[4]);
+ b43_phy_write(dev, 0x0003, regstack[5]);
+ b43_phy_write(dev, 0x0001, regstack[6]);
+ b43_phy_write(dev, 0x0030, regstack[7]);
+
+ b43_radio_write16(dev, 0x0043, regstack[8]);
+ b43_radio_write16(dev, 0x007A, regstack[9]);
+
+ b43_radio_write16(dev, 0x0052,
+ (b43_radio_read16(dev, 0x0052) & 0x000F)
+ | regstack[11]);
+
+ b43_write16(dev, 0x03EC, regstack[10]);
+ }
+ b43_phy_write(dev, 0x0015, regstack[0]);
+}
+
+static u16 lo_measure_feedthrough(struct b43_wldev *dev,
+ u16 lna, u16 pga, u16 trsw_rx)
+{
+ struct b43_phy *phy = &dev->phy;
+ u16 rfover;
+ u16 feedthrough;
+
+ if (phy->gmode) {
+ lna <<= B43_PHY_RFOVERVAL_LNA_SHIFT;
+ pga <<= B43_PHY_RFOVERVAL_PGA_SHIFT;
+
+ B43_WARN_ON(lna & ~B43_PHY_RFOVERVAL_LNA);
+ B43_WARN_ON(pga & ~B43_PHY_RFOVERVAL_PGA);
+/*FIXME This assertion fails B43_WARN_ON(trsw_rx & ~(B43_PHY_RFOVERVAL_TRSWRX |
+ B43_PHY_RFOVERVAL_BW));
+*/
+ trsw_rx &= (B43_PHY_RFOVERVAL_TRSWRX | B43_PHY_RFOVERVAL_BW);
+
+ /* Construct the RF Override Value */
+ rfover = B43_PHY_RFOVERVAL_UNK;
+ rfover |= pga;
+ rfover |= lna;
+ rfover |= trsw_rx;
+ if ((dev->dev->bus->sprom.r1.boardflags_lo & B43_BFL_EXTLNA) &&
+ phy->rev > 6)
+ rfover |= B43_PHY_RFOVERVAL_EXTLNA;
+
+ b43_phy_write(dev, B43_PHY_PGACTL, 0xE300);
+ b43_phy_write(dev, B43_PHY_RFOVERVAL, rfover);
+ udelay(10);
+ rfover |= B43_PHY_RFOVERVAL_BW_LBW;
+ b43_phy_write(dev, B43_PHY_RFOVERVAL, rfover);
+ udelay(10);
+ rfover |= B43_PHY_RFOVERVAL_BW_LPF;
+ b43_phy_write(dev, B43_PHY_RFOVERVAL, rfover);
+ udelay(10);
+ b43_phy_write(dev, B43_PHY_PGACTL, 0xF300);
+ } else {
+ pga |= B43_PHY_PGACTL_UNKNOWN;
+ b43_phy_write(dev, B43_PHY_PGACTL, pga);
+ udelay(10);
+ pga |= B43_PHY_PGACTL_LOWBANDW;
+ b43_phy_write(dev, B43_PHY_PGACTL, pga);
+ udelay(10);
+ pga |= B43_PHY_PGACTL_LPF;
+ b43_phy_write(dev, B43_PHY_PGACTL, pga);
+ }
+ udelay(21);
+ feedthrough = b43_phy_read(dev, B43_PHY_LO_LEAKAGE);
+
+ /* This is a good place to check if we need to relax a bit,
+ * as this is the main function called regularly
+ * in the LO calibration. */
+ cond_resched();
+
+ return feedthrough;
+}
+
+/* TXCTL Register and Value Table.
+ * Returns the "TXCTL Register".
+ * "value" is the "TXCTL Value".
+ * "pad_mix_gain" is the PAD Mixer Gain.
+ */
+static u16 lo_txctl_register_table(struct b43_wldev *dev,
+ u16 * value, u16 * pad_mix_gain)
+{
+ struct b43_phy *phy = &dev->phy;
+ u16 reg, v, padmix;
+
+ if (phy->type == B43_PHYTYPE_B) {
+ v = 0x30;
+ if (phy->radio_rev <= 5) {
+ reg = 0x43;
+ padmix = 0;
+ } else {
+ reg = 0x52;
+ padmix = 5;
+ }
+ } else {
+ if (phy->rev >= 2 && phy->radio_rev == 8) {
+ reg = 0x43;
+ v = 0x10;
+ padmix = 2;
+ } else {
+ reg = 0x52;
+ v = 0x30;
+ padmix = 5;
+ }
+ }
+ if (value)
+ *value = v;
+ if (pad_mix_gain)
+ *pad_mix_gain = padmix;
+
+ return reg;
+}
+
+static void lo_measure_txctl_values(struct b43_wldev *dev)
+{
+ struct b43_phy *phy = &dev->phy;
+ struct b43_txpower_lo_control *lo = phy->lo_control;
+ u16 reg, mask;
+ u16 trsw_rx, pga;
+ u16 radio_pctl_reg;
+
+ static const u8 tx_bias_values[] = {
+ 0x09, 0x08, 0x0A, 0x01, 0x00,
+ 0x02, 0x05, 0x04, 0x06,
+ };
+ static const u8 tx_magn_values[] = {
+ 0x70, 0x40,
+ };
+
+ if (!has_loopback_gain(phy)) {
+ radio_pctl_reg = 6;
+ trsw_rx = 2;
+ pga = 0;
+ } else {
+ int lb_gain; /* Loopback gain (in dB) */
+
+ trsw_rx = 0;
+ lb_gain = phy->max_lb_gain / 2;
+ if (lb_gain > 10) {
+ radio_pctl_reg = 0;
+ pga = abs(10 - lb_gain) / 6;
+ pga = limit_value(pga, 0, 15);
+ } else {
+ int cmp_val;
+ int tmp;
+
+ pga = 0;
+ cmp_val = 0x24;
+ if ((phy->rev >= 2) &&
+ (phy->radio_ver == 0x2050) && (phy->radio_rev == 8))
+ cmp_val = 0x3C;
+ tmp = lb_gain;
+ if ((10 - lb_gain) < cmp_val)
+ tmp = (10 - lb_gain);
+ if (tmp < 0)
+ tmp += 6;
+ else
+ tmp += 3;
+ cmp_val /= 4;
+ tmp /= 4;
+ if (tmp >= cmp_val)
+ radio_pctl_reg = cmp_val;
+ else
+ radio_pctl_reg = tmp;
+ }
+ }
+ b43_radio_write16(dev, 0x43, (b43_radio_read16(dev, 0x43)
+ & 0xFFF0) | radio_pctl_reg);
+ b43_phy_set_baseband_attenuation(dev, 2);
+
+ reg = lo_txctl_register_table(dev, &mask, NULL);
+ mask = ~mask;
+ b43_radio_write16(dev, reg, b43_radio_read16(dev, reg)
+ & mask);
+
+ if (has_tx_magnification(phy)) {
+ int i, j;
+ int feedthrough;
+ int min_feedth = 0xFFFF;
+ u8 tx_magn, tx_bias;
+
+ for (i = 0; i < ARRAY_SIZE(tx_magn_values); i++) {
+ tx_magn = tx_magn_values[i];
+ b43_radio_write16(dev, 0x52,
+ (b43_radio_read16(dev, 0x52)
+ & 0xFF0F) | tx_magn);
+ for (j = 0; j < ARRAY_SIZE(tx_bias_values); j++) {
+ tx_bias = tx_bias_values[j];
+ b43_radio_write16(dev, 0x52,
+ (b43_radio_read16(dev, 0x52)
+ & 0xFFF0) | tx_bias);
+ feedthrough =
+ lo_measure_feedthrough(dev, 0, pga,
+ trsw_rx);
+ if (feedthrough < min_feedth) {
+ lo->tx_bias = tx_bias;
+ lo->tx_magn = tx_magn;
+ min_feedth = feedthrough;
+ }
+ if (lo->tx_bias == 0)
+ break;
+ }
+ b43_radio_write16(dev, 0x52,
+ (b43_radio_read16(dev, 0x52)
+ & 0xFF00) | lo->tx_bias | lo->
+ tx_magn);
+ }
+ } else {
+ lo->tx_magn = 0;
+ lo->tx_bias = 0;
+ b43_radio_write16(dev, 0x52, b43_radio_read16(dev, 0x52)
+ & 0xFFF0); /* TX bias == 0 */
+ }
+}
+
+static void lo_read_power_vector(struct b43_wldev *dev)
+{
+ struct b43_phy *phy = &dev->phy;
+ struct b43_txpower_lo_control *lo = phy->lo_control;
+ u16 i;
+ u64 tmp;
+ u64 power_vector = 0;
+ int rf_offset, bb_offset;
+ struct b43_loctl *loctl;
+
+ for (i = 0; i < 8; i += 2) {
+ tmp = b43_shm_read16(dev, B43_SHM_SHARED, 0x310 + i);
+ /* Clear the top byte. We get holes in the bitmap... */
+ tmp &= 0xFF;
+ power_vector |= (tmp << (i * 8));
+ /* Clear the vector on the device. */
+ b43_shm_write16(dev, B43_SHM_SHARED, 0x310 + i, 0);
+ }
+
+ if (power_vector)
+ lo->power_vector = power_vector;
+ power_vector = lo->power_vector;
+
+ for (i = 0; i < 64; i++) {
+ if (power_vector & ((u64) 1ULL << i)) {
+ /* Now figure out which b43_loctl corresponds
+ * to this bit.
+ */
+ rf_offset = i / lo->rfatt_list.len;
+ bb_offset = i % lo->rfatt_list.len; //FIXME?
+ loctl =
+ b43_get_lo_g_ctl(dev,
+ &lo->rfatt_list.list[rf_offset],
+ &lo->bbatt_list.list[bb_offset]);
+ /* And mark it as "used", as the device told us
+ * through the bitmap it is using it.
+ */
+ loctl->used = 1;
+ }
+ }
+}
+
+/* 802.11/LO/GPHY/MeasuringGains */
+static void lo_measure_gain_values(struct b43_wldev *dev,
+ s16 max_rx_gain, int use_trsw_rx)
+{
+ struct b43_phy *phy = &dev->phy;
+ u16 tmp;
+
+ if (max_rx_gain < 0)
+ max_rx_gain = 0;
+
+ if (has_loopback_gain(phy)) {
+ int trsw_rx = 0;
+ int trsw_rx_gain;
+
+ if (use_trsw_rx) {
+ trsw_rx_gain = phy->trsw_rx_gain / 2;
+ if (max_rx_gain >= trsw_rx_gain) {
+ trsw_rx_gain = max_rx_gain - trsw_rx_gain;
+ trsw_rx = 0x20;
+ }
+ } else
+ trsw_rx_gain = max_rx_gain;
+ if (trsw_rx_gain < 9) {
+ phy->lna_lod_gain = 0;
+ } else {
+ phy->lna_lod_gain = 1;
+ trsw_rx_gain -= 8;
+ }
+ trsw_rx_gain = limit_value(trsw_rx_gain, 0, 0x2D);
+ phy->pga_gain = trsw_rx_gain / 3;
+ if (phy->pga_gain >= 5) {
+ phy->pga_gain -= 5;
+ phy->lna_gain = 2;
+ } else
+ phy->lna_gain = 0;
+ } else {
+ phy->lna_gain = 0;
+ phy->trsw_rx_gain = 0x20;
+ if (max_rx_gain >= 0x14) {
+ phy->lna_lod_gain = 1;
+ phy->pga_gain = 2;
+ } else if (max_rx_gain >= 0x12) {
+ phy->lna_lod_gain = 1;
+ phy->pga_gain = 1;
+ } else if (max_rx_gain >= 0xF) {
+ phy->lna_lod_gain = 1;
+ phy->pga_gain = 0;
+ } else {
+ phy->lna_lod_gain = 0;
+ phy->pga_gain = 0;
+ }
+ }
+
+ tmp = b43_radio_read16(dev, 0x7A);
+ if (phy->lna_lod_gain == 0)
+ tmp &= ~0x0008;
+ else
+ tmp |= 0x0008;
+ b43_radio_write16(dev, 0x7A, tmp);
+}
+
+struct lo_g_saved_values {
+ u8 old_channel;
+
+ /* Core registers */
+ u16 reg_3F4;
+ u16 reg_3E2;
+
+ /* PHY registers */
+ u16 phy_lo_mask;
+ u16 phy_extg_01;
+ u16 phy_dacctl_hwpctl;
+ u16 phy_dacctl;
+ u16 phy_base_14;
+ u16 phy_hpwr_tssictl;
+ u16 phy_analogover;
+ u16 phy_analogoverval;
+ u16 phy_rfover;
+ u16 phy_rfoverval;
+ u16 phy_classctl;
+ u16 phy_base_3E;
+ u16 phy_crs0;
+ u16 phy_pgactl;
+ u16 phy_base_2A;
+ u16 phy_syncctl;
+ u16 phy_base_30;
+ u16 phy_base_06;
+
+ /* Radio registers */
+ u16 radio_43;
+ u16 radio_7A;
+ u16 radio_52;
+};
+
+static void lo_measure_setup(struct b43_wldev *dev,
+ struct lo_g_saved_values *sav)
+{
+ struct ssb_sprom *sprom = &dev->dev->bus->sprom;
+ struct b43_phy *phy = &dev->phy;
+ struct b43_txpower_lo_control *lo = phy->lo_control;
+ u16 tmp;
+
+ if (b43_has_hardware_pctl(phy)) {
+ sav->phy_lo_mask = b43_phy_read(dev, B43_PHY_LO_MASK);
+ sav->phy_extg_01 = b43_phy_read(dev, B43_PHY_EXTG(0x01));
+ sav->phy_dacctl_hwpctl = b43_phy_read(dev, B43_PHY_DACCTL);
+ sav->phy_base_14 = b43_phy_read(dev, B43_PHY_BASE(0x14));
+ sav->phy_hpwr_tssictl = b43_phy_read(dev, B43_PHY_HPWR_TSSICTL);
+
+ b43_phy_write(dev, B43_PHY_HPWR_TSSICTL,
+ b43_phy_read(dev, B43_PHY_HPWR_TSSICTL)
+ | 0x100);
+ b43_phy_write(dev, B43_PHY_EXTG(0x01),
+ b43_phy_read(dev, B43_PHY_EXTG(0x01))
+ | 0x40);
+ b43_phy_write(dev, B43_PHY_DACCTL,
+ b43_phy_read(dev, B43_PHY_DACCTL)
+ | 0x40);
+ b43_phy_write(dev, B43_PHY_BASE(0x14),
+ b43_phy_read(dev, B43_PHY_BASE(0x14))
+ | 0x200);
+ }
+ if (phy->type == B43_PHYTYPE_B &&
+ phy->radio_ver == 0x2050 && phy->radio_rev < 6) {
+ b43_phy_write(dev, B43_PHY_BASE(0x16), 0x410);
+ b43_phy_write(dev, B43_PHY_BASE(0x17), 0x820);
+ }
+ if (!lo->rebuild && b43_has_hardware_pctl(phy))
+ lo_read_power_vector(dev);
+ if (phy->rev >= 2) {
+ sav->phy_analogover = b43_phy_read(dev, B43_PHY_ANALOGOVER);
+ sav->phy_analogoverval =
+ b43_phy_read(dev, B43_PHY_ANALOGOVERVAL);
+ sav->phy_rfover = b43_phy_read(dev, B43_PHY_RFOVER);
+ sav->phy_rfoverval = b43_phy_read(dev, B43_PHY_RFOVERVAL);
+ sav->phy_classctl = b43_phy_read(dev, B43_PHY_CLASSCTL);
+ sav->phy_base_3E = b43_phy_read(dev, B43_PHY_BASE(0x3E));
+ sav->phy_crs0 = b43_phy_read(dev, B43_PHY_CRS0);
+
+ b43_phy_write(dev, B43_PHY_CLASSCTL,
+ b43_phy_read(dev, B43_PHY_CLASSCTL)
+ & 0xFFFC);
+ b43_phy_write(dev, B43_PHY_CRS0, b43_phy_read(dev, B43_PHY_CRS0)
+ & 0x7FFF);
+ b43_phy_write(dev, B43_PHY_ANALOGOVER,
+ b43_phy_read(dev, B43_PHY_ANALOGOVER)
+ | 0x0003);
+ b43_phy_write(dev, B43_PHY_ANALOGOVERVAL,
+ b43_phy_read(dev, B43_PHY_ANALOGOVERVAL)
+ & 0xFFFC);
+ if (phy->type == B43_PHYTYPE_G) {
+ if ((phy->rev >= 7) &&
+ (sprom->r1.boardflags_lo & B43_BFL_EXTLNA)) {
+ b43_phy_write(dev, B43_PHY_RFOVER, 0x933);
+ } else {
+ b43_phy_write(dev, B43_PHY_RFOVER, 0x133);
+ }
+ } else {
+ b43_phy_write(dev, B43_PHY_RFOVER, 0);
+ }
+ b43_phy_write(dev, B43_PHY_BASE(0x3E), 0);
+ }
+ sav->reg_3F4 = b43_read16(dev, 0x3F4);
+ sav->reg_3E2 = b43_read16(dev, 0x3E2);
+ sav->radio_43 = b43_radio_read16(dev, 0x43);
+ sav->radio_7A = b43_radio_read16(dev, 0x7A);
+ sav->phy_pgactl = b43_phy_read(dev, B43_PHY_PGACTL);
+ sav->phy_base_2A = b43_phy_read(dev, B43_PHY_BASE(0x2A));
+ sav->phy_syncctl = b43_phy_read(dev, B43_PHY_SYNCCTL);
+ sav->phy_dacctl = b43_phy_read(dev, B43_PHY_DACCTL);
+
+ if (!has_tx_magnification(phy)) {
+ sav->radio_52 = b43_radio_read16(dev, 0x52);
+ sav->radio_52 &= 0x00F0;
+ }
+ if (phy->type == B43_PHYTYPE_B) {
+ sav->phy_base_30 = b43_phy_read(dev, B43_PHY_BASE(0x30));
+ sav->phy_base_06 = b43_phy_read(dev, B43_PHY_BASE(0x06));
+ b43_phy_write(dev, B43_PHY_BASE(0x30), 0x00FF);
+ b43_phy_write(dev, B43_PHY_BASE(0x06), 0x3F3F);
+ } else {
+ b43_write16(dev, 0x3E2, b43_read16(dev, 0x3E2)
+ | 0x8000);
+ }
+ b43_write16(dev, 0x3F4, b43_read16(dev, 0x3F4)
+ & 0xF000);
+
+ tmp =
+ (phy->type == B43_PHYTYPE_G) ? B43_PHY_LO_MASK : B43_PHY_BASE(0x2E);
+ b43_phy_write(dev, tmp, 0x007F);
+
+ tmp = sav->phy_syncctl;
+ b43_phy_write(dev, B43_PHY_SYNCCTL, tmp & 0xFF7F);
+ tmp = sav->radio_7A;
+ b43_radio_write16(dev, 0x007A, tmp & 0xFFF0);
+
+ b43_phy_write(dev, B43_PHY_BASE(0x2A), 0x8A3);
+ if (phy->type == B43_PHYTYPE_G ||
+ (phy->type == B43_PHYTYPE_B &&
+ phy->radio_ver == 0x2050 && phy->radio_rev >= 6)) {
+ b43_phy_write(dev, B43_PHY_BASE(0x2B), 0x1003);
+ } else
+ b43_phy_write(dev, B43_PHY_BASE(0x2B), 0x0802);
+ if (phy->rev >= 2)
+ b43_dummy_transmission(dev);
+ b43_radio_selectchannel(dev, 6, 0);
+ b43_radio_read16(dev, 0x51); /* dummy read */
+ if (phy->type == B43_PHYTYPE_G)
+ b43_phy_write(dev, B43_PHY_BASE(0x2F), 0);
+ if (lo->rebuild)
+ lo_measure_txctl_values(dev);
+ if (phy->type == B43_PHYTYPE_G && phy->rev >= 3) {
+ b43_phy_write(dev, B43_PHY_LO_MASK, 0xC078);
+ } else {
+ if (phy->type == B43_PHYTYPE_B)
+ b43_phy_write(dev, B43_PHY_BASE(0x2E), 0x8078);
+ else
+ b43_phy_write(dev, B43_PHY_LO_MASK, 0x8078);
+ }
+}
+
+static void lo_measure_restore(struct b43_wldev *dev,
+ struct lo_g_saved_values *sav)
+{
+ struct b43_phy *phy = &dev->phy;
+ struct b43_txpower_lo_control *lo = phy->lo_control;
+ u16 tmp;
+
+ if (phy->rev >= 2) {
+ b43_phy_write(dev, B43_PHY_PGACTL, 0xE300);
+ tmp = (phy->pga_gain << 8);
+ b43_phy_write(dev, B43_PHY_RFOVERVAL, tmp | 0xA0);
+ udelay(5);
+ b43_phy_write(dev, B43_PHY_RFOVERVAL, tmp | 0xA2);
+ udelay(2);
+ b43_phy_write(dev, B43_PHY_RFOVERVAL, tmp | 0xA3);
+ } else {
+ tmp = (phy->pga_gain | 0xEFA0);
+ b43_phy_write(dev, B43_PHY_PGACTL, tmp);
+ }
+ if (b43_has_hardware_pctl(phy)) {
+ b43_gphy_dc_lt_init(dev);
+ } else {
+ if (lo->rebuild)
+ b43_lo_g_adjust_to(dev, 3, 2, 0);
+ else
+ b43_lo_g_adjust(dev);
+ }
+ if (phy->type == B43_PHYTYPE_G) {
+ if (phy->rev >= 3)
+ b43_phy_write(dev, B43_PHY_BASE(0x2E), 0xC078);
+ else
+ b43_phy_write(dev, B43_PHY_BASE(0x2E), 0x8078);
+ if (phy->rev >= 2)
+ b43_phy_write(dev, B43_PHY_BASE(0x2F), 0x0202);
+ else
+ b43_phy_write(dev, B43_PHY_BASE(0x2F), 0x0101);
+ }
+ b43_write16(dev, 0x3F4, sav->reg_3F4);
+ b43_phy_write(dev, B43_PHY_PGACTL, sav->phy_pgactl);
+ b43_phy_write(dev, B43_PHY_BASE(0x2A), sav->phy_base_2A);
+ b43_phy_write(dev, B43_PHY_SYNCCTL, sav->phy_syncctl);
+ b43_phy_write(dev, B43_PHY_DACCTL, sav->phy_dacctl);
+ b43_radio_write16(dev, 0x43, sav->radio_43);
+ b43_radio_write16(dev, 0x7A, sav->radio_7A);
+ if (!has_tx_magnification(phy)) {
+ tmp = sav->radio_52;
+ b43_radio_write16(dev, 0x52, (b43_radio_read16(dev, 0x52)
+ & 0xFF0F) | tmp);
+ }
+ b43_write16(dev, 0x3E2, sav->reg_3E2);
+ if (phy->type == B43_PHYTYPE_B &&
+ phy->radio_ver == 0x2050 && phy->radio_rev <= 5) {
+ b43_phy_write(dev, B43_PHY_BASE(0x30), sav->phy_base_30);
+ b43_phy_write(dev, B43_PHY_BASE(0x06), sav->phy_base_06);
+ }
+ if (phy->rev >= 2) {
+ b43_phy_write(dev, B43_PHY_ANALOGOVER, sav->phy_analogover);
+ b43_phy_write(dev, B43_PHY_ANALOGOVERVAL,
+ sav->phy_analogoverval);
+ b43_phy_write(dev, B43_PHY_CLASSCTL, sav->phy_classctl);
+ b43_phy_write(dev, B43_PHY_RFOVER, sav->phy_rfover);
+ b43_phy_write(dev, B43_PHY_RFOVERVAL, sav->phy_rfoverval);
+ b43_phy_write(dev, B43_PHY_BASE(0x3E), sav->phy_base_3E);
+ b43_phy_write(dev, B43_PHY_CRS0, sav->phy_crs0);
+ }
+ if (b43_has_hardware_pctl(phy)) {
+ tmp = (sav->phy_lo_mask & 0xBFFF);
+ b43_phy_write(dev, B43_PHY_LO_MASK, tmp);
+ b43_phy_write(dev, B43_PHY_EXTG(0x01), sav->phy_extg_01);
+ b43_phy_write(dev, B43_PHY_DACCTL, sav->phy_dacctl_hwpctl);
+ b43_phy_write(dev, B43_PHY_BASE(0x14), sav->phy_base_14);
+ b43_phy_write(dev, B43_PHY_HPWR_TSSICTL, sav->phy_hpwr_tssictl);
+ }
+ b43_radio_selectchannel(dev, sav->old_channel, 1);
+}
+
+struct b43_lo_g_statemachine {
+ int current_state;
+ int nr_measured;
+ int state_val_multiplier;
+ u16 lowest_feedth;
+ struct b43_loctl min_loctl;
+};
+
+/* Loop over each possible value in this state. */
+static int lo_probe_possible_loctls(struct b43_wldev *dev,
+ struct b43_loctl *probe_loctl,
+ struct b43_lo_g_statemachine *d)
+{
+ struct b43_phy *phy = &dev->phy;
+ struct b43_txpower_lo_control *lo = phy->lo_control;
+ struct b43_loctl test_loctl;
+ struct b43_loctl orig_loctl;
+ struct b43_loctl prev_loctl = {
+ .i = -100,
+ .q = -100,
+ };
+ int i;
+ int begin, end;
+ int found_lower = 0;
+ u16 feedth;
+
+ static const struct b43_loctl modifiers[] = {
+ {.i = 1,.q = 1,},
+ {.i = 1,.q = 0,},
+ {.i = 1,.q = -1,},
+ {.i = 0,.q = -1,},
+ {.i = -1,.q = -1,},
+ {.i = -1,.q = 0,},
+ {.i = -1,.q = 1,},
+ {.i = 0,.q = 1,},
+ };
+
+ if (d->current_state == 0) {
+ begin = 1;
+ end = 8;
+ } else if (d->current_state % 2 == 0) {
+ begin = d->current_state - 1;
+ end = d->current_state + 1;
+ } else {
+ begin = d->current_state - 2;
+ end = d->current_state + 2;
+ }
+ if (begin < 1)
+ begin += 8;
+ if (end > 8)
+ end -= 8;
+
+ memcpy(&orig_loctl, probe_loctl, sizeof(struct b43_loctl));
+ i = begin;
+ d->current_state = i;
+ while (1) {
+ B43_WARN_ON(!(i >= 1 && i <= 8));
+ memcpy(&test_loctl, &orig_loctl, sizeof(struct b43_loctl));
+ test_loctl.i += modifiers[i - 1].i * d->state_val_multiplier;
+ test_loctl.q += modifiers[i - 1].q * d->state_val_multiplier;
+ if ((test_loctl.i != prev_loctl.i ||
+ test_loctl.q != prev_loctl.q) &&
+ (abs(test_loctl.i) <= 16 && abs(test_loctl.q) <= 16)) {
+ b43_lo_write(dev, &test_loctl);
+ feedth = lo_measure_feedthrough(dev, phy->lna_gain,
+ phy->pga_gain,
+ phy->trsw_rx_gain);
+ if (feedth < d->lowest_feedth) {
+ memcpy(probe_loctl, &test_loctl,
+ sizeof(struct b43_loctl));
+ found_lower = 1;
+ d->lowest_feedth = feedth;
+ if ((d->nr_measured < 2) &&
+ (!has_loopback_gain(phy) || lo->rebuild))
+ break;
+ }
+ }
+ memcpy(&prev_loctl, &test_loctl, sizeof(prev_loctl));
+ if (i == end)
+ break;
+ if (i == 8)
+ i = 1;
+ else
+ i++;
+ d->current_state = i;
+ }
+
+ return found_lower;
+}
+
+static void lo_probe_loctls_statemachine(struct b43_wldev *dev,
+ struct b43_loctl *loctl,
+ int *max_rx_gain)
+{
+ struct b43_phy *phy = &dev->phy;
+ struct b43_txpower_lo_control *lo = phy->lo_control;
+ struct b43_lo_g_statemachine d;
+ u16 feedth;
+ int found_lower;
+ struct b43_loctl probe_loctl;
+ int max_repeat = 1, repeat_cnt = 0;
+
+ d.nr_measured = 0;
+ d.state_val_multiplier = 1;
+ if (has_loopback_gain(phy) && !lo->rebuild)
+ d.state_val_multiplier = 3;
+
+ memcpy(&d.min_loctl, loctl, sizeof(struct b43_loctl));
+ if (has_loopback_gain(phy) && lo->rebuild)
+ max_repeat = 4;
+ do {
+ b43_lo_write(dev, &d.min_loctl);
+ feedth = lo_measure_feedthrough(dev, phy->lna_gain,
+ phy->pga_gain,
+ phy->trsw_rx_gain);
+ if (!lo->rebuild && feedth < 0x258) {
+ if (feedth >= 0x12C)
+ *max_rx_gain += 6;
+ else
+ *max_rx_gain += 3;
+ feedth = lo_measure_feedthrough(dev, phy->lna_gain,
+ phy->pga_gain,
+ phy->trsw_rx_gain);
+ }
+ d.lowest_feedth = feedth;
+
+ d.current_state = 0;
+ do {
+ B43_WARN_ON(!
+ (d.current_state >= 0
+ && d.current_state <= 8));
+ memcpy(&probe_loctl, &d.min_loctl,
+ sizeof(struct b43_loctl));
+ found_lower =
+ lo_probe_possible_loctls(dev, &probe_loctl, &d);
+ if (!found_lower)
+ break;
+ if ((probe_loctl.i == d.min_loctl.i) &&
+ (probe_loctl.q == d.min_loctl.q))
+ break;
+ memcpy(&d.min_loctl, &probe_loctl,
+ sizeof(struct b43_loctl));
+ d.nr_measured++;
+ } while (d.nr_measured < 24);
+ memcpy(loctl, &d.min_loctl, sizeof(struct b43_loctl));
+
+ if (has_loopback_gain(phy)) {
+ if (d.lowest_feedth > 0x1194)
+ *max_rx_gain -= 6;
+ else if (d.lowest_feedth < 0x5DC)
+ *max_rx_gain += 3;
+ if (repeat_cnt == 0) {
+ if (d.lowest_feedth <= 0x5DC) {
+ d.state_val_multiplier = 1;
+ repeat_cnt++;
+ } else
+ d.state_val_multiplier = 2;
+ } else if (repeat_cnt == 2)
+ d.state_val_multiplier = 1;
+ }
+ lo_measure_gain_values(dev, *max_rx_gain,
+ has_loopback_gain(phy));
+ } while (++repeat_cnt < max_repeat);
+}
+
+#if B43_CALIB_ALL_LOCTLS
+static const struct b43_rfatt b43_full_rfatt_list_items[] = {
+ { .att = 0, .with_padmix = 0, },
+ { .att = 1, .with_padmix = 0, },
+ { .att = 2, .with_padmix = 0, },
+ { .att = 3, .with_padmix = 0, },
+ { .att = 4, .with_padmix = 0, },
+ { .att = 5, .with_padmix = 0, },
+ { .att = 6, .with_padmix = 0, },
+ { .att = 7, .with_padmix = 0, },
+ { .att = 8, .with_padmix = 0, },
+ { .att = 9, .with_padmix = 0, },
+ { .att = 10, .with_padmix = 0, },
+ { .att = 11, .with_padmix = 0, },
+ { .att = 12, .with_padmix = 0, },
+ { .att = 13, .with_padmix = 0, },
+ { .att = 14, .with_padmix = 0, },
+ { .att = 15, .with_padmix = 0, },
+ { .att = 0, .with_padmix = 1, },
+ { .att = 1, .with_padmix = 1, },
+ { .att = 2, .with_padmix = 1, },
+ { .att = 3, .with_padmix = 1, },
+ { .att = 4, .with_padmix = 1, },
+ { .att = 5, .with_padmix = 1, },
+ { .att = 6, .with_padmix = 1, },
+ { .att = 7, .with_padmix = 1, },
+ { .att = 8, .with_padmix = 1, },
+ { .att = 9, .with_padmix = 1, },
+ { .att = 10, .with_padmix = 1, },
+ { .att = 11, .with_padmix = 1, },
+ { .att = 12, .with_padmix = 1, },
+ { .att = 13, .with_padmix = 1, },
+ { .att = 14, .with_padmix = 1, },
+ { .att = 15, .with_padmix = 1, },
+};
+static const struct b43_rfatt_list b43_full_rfatt_list = {
+ .list = b43_full_rfatt_list_items,
+ .len = ARRAY_SIZE(b43_full_rfatt_list_items),
+};
+
+static const struct b43_bbatt b43_full_bbatt_list_items[] = {
+ { .att = 0, },
+ { .att = 1, },
+ { .att = 2, },
+ { .att = 3, },
+ { .att = 4, },
+ { .att = 5, },
+ { .att = 6, },
+ { .att = 7, },
+ { .att = 8, },
+ { .att = 9, },
+ { .att = 10, },
+ { .att = 11, },
+};
+static const struct b43_bbatt_list b43_full_bbatt_list = {
+ .list = b43_full_bbatt_list_items,
+ .len = ARRAY_SIZE(b43_full_bbatt_list_items),
+};
+#endif /* B43_CALIB_ALL_LOCTLS */
+
+static void lo_measure(struct b43_wldev *dev)
+{
+ struct b43_phy *phy = &dev->phy;
+ struct b43_txpower_lo_control *lo = phy->lo_control;
+ struct b43_loctl loctl = {
+ .i = 0,
+ .q = 0,
+ };
+ struct b43_loctl *ploctl;
+ int max_rx_gain;
+ int rfidx, bbidx;
+ const struct b43_bbatt_list *bbatt_list;
+ const struct b43_rfatt_list *rfatt_list;
+
+ /* Values from the "TXCTL Register and Value Table" */
+ u16 txctl_reg;
+ u16 txctl_value;
+ u16 pad_mix_gain;
+
+ bbatt_list = &lo->bbatt_list;
+ rfatt_list = &lo->rfatt_list;
+#if B43_CALIB_ALL_LOCTLS
+ bbatt_list = &b43_full_bbatt_list;
+ rfatt_list = &b43_full_rfatt_list;
+#endif
+
+ txctl_reg = lo_txctl_register_table(dev, &txctl_value, &pad_mix_gain);
+
+ for (rfidx = 0; rfidx < rfatt_list->len; rfidx++) {
+
+ b43_radio_write16(dev, 0x43, (b43_radio_read16(dev, 0x43)
+ & 0xFFF0) |
+ rfatt_list->list[rfidx].att);
+ b43_radio_write16(dev, txctl_reg,
+ (b43_radio_read16(dev, txctl_reg)
+ & ~txctl_value)
+ | (rfatt_list->list[rfidx].with_padmix ?
+ txctl_value : 0));
+
+ for (bbidx = 0; bbidx < bbatt_list->len; bbidx++) {
+ if (lo->rebuild) {
+#if B43_CALIB_ALL_LOCTLS
+ ploctl = b43_get_lo_g_ctl(dev,
+ &rfatt_list->list[rfidx],
+ &bbatt_list->list[bbidx]);
+#else
+ ploctl = b43_get_lo_g_ctl_nopadmix(dev,
+ &rfatt_list->
+ list[rfidx],
+ &bbatt_list->
+ list[bbidx]);
+#endif
+ } else {
+ ploctl = b43_get_lo_g_ctl(dev,
+ &rfatt_list->list[rfidx],
+ &bbatt_list->list[bbidx]);
+ if (!ploctl->used)
+ continue;
+ }
+ memcpy(&loctl, ploctl, sizeof(loctl));
+ loctl.i = 0;
+ loctl.q = 0;
+
+ max_rx_gain = rfatt_list->list[rfidx].att * 2;
+ max_rx_gain += bbatt_list->list[bbidx].att / 2;
+ if (rfatt_list->list[rfidx].with_padmix)
+ max_rx_gain -= pad_mix_gain;
+ if (has_loopback_gain(phy))
+ max_rx_gain += phy->max_lb_gain;
+ lo_measure_gain_values(dev, max_rx_gain,
+ has_loopback_gain(phy));
+
+ b43_phy_set_baseband_attenuation(dev,
+ bbatt_list->list[bbidx].att);
+ lo_probe_loctls_statemachine(dev, &loctl, &max_rx_gain);
+ if (phy->type == B43_PHYTYPE_B) {
+ loctl.i++;
+ loctl.q++;
+ }
+ b43_loctl_set_calibrated(&loctl, 1);
+ memcpy(ploctl, &loctl, sizeof(loctl));
+ }
+ }
+}
+
+#if B43_DEBUG
+static void do_validate_loctl(struct b43_wldev *dev, struct b43_loctl *control)
+{
+ const int is_initializing = (b43_status(dev) == B43_STAT_UNINIT);
+ int i = control->i;
+ int q = control->q;
+
+ if (b43_loctl_is_calibrated(control)) {
+ if ((abs(i) > 16) || (abs(q) > 16))
+ goto error;
+ } else {
+ if (control->used)
+ goto error;
+ if (dev->phy.lo_control->rebuild) {
+ control->i = 0;
+ control->q = 0;
+ if ((i != B43_LOCTL_POISON) ||
+ (q != B43_LOCTL_POISON))
+ goto error;
+ }
+ }
+ if (is_initializing && control->used)
+ goto error;
+
+ return;
+error:
+ b43err(dev->wl, "LO control pair validation failed "
+ "(I: %d, Q: %d, used %u, calib: %u, initing: %d)\n",
+ i, q, control->used,
+ b43_loctl_is_calibrated(control),
+ is_initializing);
+}
+
+static void validate_all_loctls(struct b43_wldev *dev)
+{
+ b43_call_for_each_loctl(dev, do_validate_loctl);
+}
+
+static void do_reset_calib(struct b43_wldev *dev, struct b43_loctl *control)
+{
+ if (dev->phy.lo_control->rebuild ||
+ control->used) {
+ b43_loctl_set_calibrated(control, 0);
+ control->i = B43_LOCTL_POISON;
+ control->q = B43_LOCTL_POISON;
+ }
+}
+
+static void reset_all_loctl_calibration_states(struct b43_wldev *dev)
+{
+ b43_call_for_each_loctl(dev, do_reset_calib);
+}
+
+#else /* B43_DEBUG */
+static inline void validate_all_loctls(struct b43_wldev *dev) { }
+static inline void reset_all_loctl_calibration_states(struct b43_wldev *dev) { }
+#endif /* B43_DEBUG */
+
+void b43_lo_g_measure(struct b43_wldev *dev)
+{
+ struct b43_phy *phy = &dev->phy;
+ struct lo_g_saved_values uninitialized_var(sav);
+
+ B43_WARN_ON((phy->type != B43_PHYTYPE_B) &&
+ (phy->type != B43_PHYTYPE_G));
+
+ sav.old_channel = phy->channel;
+ lo_measure_setup(dev, &sav);
+ reset_all_loctl_calibration_states(dev);
+ lo_measure(dev);
+ lo_measure_restore(dev, &sav);
+
+ validate_all_loctls(dev);
+
+ phy->lo_control->lo_measured = 1;
+ phy->lo_control->rebuild = 0;
+}
+
+#if B43_DEBUG
+static void validate_loctl_calibration(struct b43_wldev *dev,
+ struct b43_loctl *loctl,
+ struct b43_rfatt *rfatt,
+ struct b43_bbatt *bbatt)
+{
+ if (b43_loctl_is_calibrated(loctl))
+ return;
+ if (!dev->phy.lo_control->lo_measured) {
+ /* On init we set the attenuation values before we
+ * calibrated the LO. I guess that's OK. */
+ return;
+ }
+ b43err(dev->wl, "Adjusting Local Oscillator to an uncalibrated "
+ "control pair: rfatt=%u,%spadmix bbatt=%u\n",
+ rfatt->att,
+ (rfatt->with_padmix) ? "" : "no-",
+ bbatt->att);
+}
+#else
+static inline void validate_loctl_calibration(struct b43_wldev *dev,
+ struct b43_loctl *loctl,
+ struct b43_rfatt *rfatt,
+ struct b43_bbatt *bbatt)
+{
+}
+#endif
+
+static inline void fixup_rfatt_for_txcontrol(struct b43_rfatt *rf,
+ u8 tx_control)
+{
+ if (tx_control & B43_TXCTL_TXMIX) {
+ if (rf->att < 5)
+ rf->att = 4;
+ }
+}
+
+void b43_lo_g_adjust(struct b43_wldev *dev)
+{
+ struct b43_phy *phy = &dev->phy;
+ struct b43_rfatt rf;
+ struct b43_loctl *loctl;
+
+ memcpy(&rf, &phy->rfatt, sizeof(rf));
+ fixup_rfatt_for_txcontrol(&rf, phy->tx_control);
+
+ loctl = b43_get_lo_g_ctl(dev, &rf, &phy->bbatt);
+ validate_loctl_calibration(dev, loctl, &rf, &phy->bbatt);
+ b43_lo_write(dev, loctl);
+}
+
+void b43_lo_g_adjust_to(struct b43_wldev *dev,
+ u16 rfatt, u16 bbatt, u16 tx_control)
+{
+ struct b43_rfatt rf;
+ struct b43_bbatt bb;
+ struct b43_loctl *loctl;
+
+ memset(&rf, 0, sizeof(rf));
+ memset(&bb, 0, sizeof(bb));
+ rf.att = rfatt;
+ bb.att = bbatt;
+ fixup_rfatt_for_txcontrol(&rf, tx_control);
+ loctl = b43_get_lo_g_ctl(dev, &rf, &bb);
+ validate_loctl_calibration(dev, loctl, &rf, &bb);
+ b43_lo_write(dev, loctl);
+}
+
+static void do_mark_unused(struct b43_wldev *dev, struct b43_loctl *control)
+{
+ control->used = 0;
+}
+
+void b43_lo_g_ctl_mark_all_unused(struct b43_wldev *dev)
+{
+ struct b43_phy *phy = &dev->phy;
+ struct b43_txpower_lo_control *lo = phy->lo_control;
+
+ b43_call_for_each_loctl(dev, do_mark_unused);
+ lo->rebuild = 1;
+}
+
+void b43_lo_g_ctl_mark_cur_used(struct b43_wldev *dev)
+{
+ struct b43_phy *phy = &dev->phy;
+ struct b43_rfatt rf;
+
+ memcpy(&rf, &phy->rfatt, sizeof(rf));
+ fixup_rfatt_for_txcontrol(&rf, phy->tx_control);
+
+ b43_get_lo_g_ctl(dev, &rf, &phy->bbatt)->used = 1;
+}
--- /dev/null
+#ifndef B43_LO_H_
+#define B43_LO_H_
+
+#include "phy.h"
+
+struct b43_wldev;
+
+/* Local Oscillator control value-pair. */
+struct b43_loctl {
+ /* Control values. */
+ s8 i;
+ s8 q;
+ /* "Used by hardware" flag. */
+ bool used;
+#ifdef CONFIG_B43_DEBUG
+ /* Is this lo-control-array entry calibrated? */
+ bool calibrated;
+#endif
+};
+
+/* Debugging: Poison value for i and q values. */
+#define B43_LOCTL_POISON 111
+
+/* loctl->calibrated debugging mechanism */
+#ifdef CONFIG_B43_DEBUG
+static inline void b43_loctl_set_calibrated(struct b43_loctl *loctl,
+ bool calibrated)
+{
+ loctl->calibrated = calibrated;
+}
+static inline bool b43_loctl_is_calibrated(struct b43_loctl *loctl)
+{
+ return loctl->calibrated;
+}
+#else
+static inline void b43_loctl_set_calibrated(struct b43_loctl *loctl,
+ bool calibrated)
+{
+}
+static inline bool b43_loctl_is_calibrated(struct b43_loctl *loctl)
+{
+ return 1;
+}
+#endif
+
+/* TX Power LO Control Array.
+ * Value-pairs to adjust the LocalOscillator are stored
+ * in this structure.
+ * There are two different set of values. One for "Flag is Set"
+ * and one for "Flag is Unset".
+ * By "Flag" the flag in struct b43_rfatt is meant.
+ * The Value arrays are two-dimensional. The first index
+ * is the baseband attenuation and the second index
+ * is the radio attenuation.
+ * Use b43_get_lo_g_ctl() to retrieve a value from the lists.
+ */
+struct b43_txpower_lo_control {
+#define B43_NR_BB 12
+#define B43_NR_RF 16
+ /* LO Control values, with PAD Mixer */
+ struct b43_loctl with_padmix[B43_NR_BB][B43_NR_RF];
+ /* LO Control values, without PAD Mixer */
+ struct b43_loctl no_padmix[B43_NR_BB][B43_NR_RF];
+
+ /* Flag to indicate a complete rebuild of the two tables above
+ * to the LO measuring code. */
+ bool rebuild;
+
+ /* Lists of valid RF and BB attenuation values for this device. */
+ struct b43_rfatt_list rfatt_list;
+ struct b43_bbatt_list bbatt_list;
+
+ /* Current TX Bias value */
+ u8 tx_bias;
+ /* Current TX Magnification Value (if used by the device) */
+ u8 tx_magn;
+
+ /* GPHY LO is measured. */
+ bool lo_measured;
+
+ /* Saved device PowerVector */
+ u64 power_vector;
+};
+
+/* Measure the BPHY Local Oscillator. */
+void b43_lo_b_measure(struct b43_wldev *dev);
+/* Measure the BPHY/GPHY Local Oscillator. */
+void b43_lo_g_measure(struct b43_wldev *dev);
+
+/* Adjust the Local Oscillator to the saved attenuation
+ * and txctl values.
+ */
+void b43_lo_g_adjust(struct b43_wldev *dev);
+/* Adjust to specific values. */
+void b43_lo_g_adjust_to(struct b43_wldev *dev,
+ u16 rfatt, u16 bbatt, u16 tx_control);
+
+/* Mark all possible b43_lo_g_ctl as "unused" */
+void b43_lo_g_ctl_mark_all_unused(struct b43_wldev *dev);
+/* Mark the b43_lo_g_ctl corresponding to the current
+ * attenuation values as used.
+ */
+void b43_lo_g_ctl_mark_cur_used(struct b43_wldev *dev);
+
+/* Get a reference to a LO Control value pair in the
+ * TX Power LO Control Array.
+ */
+struct b43_loctl *b43_get_lo_g_ctl(struct b43_wldev *dev,
+ const struct b43_rfatt *rfatt,
+ const struct b43_bbatt *bbatt);
+
+#endif /* B43_LO_H_ */
--- /dev/null
+/*
+
+ Broadcom B43 wireless driver
+
+ Copyright (c) 2005 Martin Langer <martin-langer@gmx.de>
+ Copyright (c) 2005 Stefano Brivio <st3@riseup.net>
+ Copyright (c) 2005, 2006 Michael Buesch <mb@bu3sch.de>
+ Copyright (c) 2005 Danny van Dyk <kugelfang@gentoo.org>
+ Copyright (c) 2005 Andreas Jaggi <andreas.jaggi@waterwave.ch>
+
+ Some parts of the code in this file are derived from the ipw2200
+ driver Copyright(c) 2003 - 2004 Intel Corporation.
+
+ This program is free software; you can redistribute it and/or modify
+ it under the terms of the GNU General Public License as published by
+ the Free Software Foundation; either version 2 of the License, or
+ (at your option) any later version.
+
+ This program is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ GNU General Public License for more details.
+
+ You should have received a copy of the GNU General Public License
+ along with this program; see the file COPYING. If not, write to
+ the Free Software Foundation, Inc., 51 Franklin Steet, Fifth Floor,
+ Boston, MA 02110-1301, USA.
+
+*/
+
+#include <linux/delay.h>
+#include <linux/init.h>
+#include <linux/moduleparam.h>
+#include <linux/if_arp.h>
+#include <linux/etherdevice.h>
+#include <linux/version.h>
+#include <linux/firmware.h>
+#include <linux/wireless.h>
+#include <linux/workqueue.h>
+#include <linux/skbuff.h>
+#include <linux/dma-mapping.h>
+#include <asm/unaligned.h>
+
+#include "b43.h"
+#include "main.h"
+#include "debugfs.h"
+#include "phy.h"
+#include "dma.h"
+#include "pio.h"
+#include "sysfs.h"
+#include "xmit.h"
+#include "sysfs.h"
+#include "lo.h"
+#include "pcmcia.h"
+
+MODULE_DESCRIPTION("Broadcom B43 wireless driver");
+MODULE_AUTHOR("Martin Langer");
+MODULE_AUTHOR("Stefano Brivio");
+MODULE_AUTHOR("Michael Buesch");
+MODULE_LICENSE("GPL");
+
+extern char *nvram_get(char *name);
+
+#if defined(CONFIG_B43_DMA) && defined(CONFIG_B43_PIO)
+static int modparam_pio;
+module_param_named(pio, modparam_pio, int, 0444);
+MODULE_PARM_DESC(pio, "enable(1) / disable(0) PIO mode");
+#elif defined(CONFIG_B43_DMA)
+# define modparam_pio 0
+#elif defined(CONFIG_B43_PIO)
+# define modparam_pio 1
+#endif
+
+static int modparam_bad_frames_preempt;
+module_param_named(bad_frames_preempt, modparam_bad_frames_preempt, int, 0444);
+MODULE_PARM_DESC(bad_frames_preempt,
+ "enable(1) / disable(0) Bad Frames Preemption");
+
+static int modparam_short_retry = B43_DEFAULT_SHORT_RETRY_LIMIT;
+module_param_named(short_retry, modparam_short_retry, int, 0444);
+MODULE_PARM_DESC(short_retry, "Short-Retry-Limit (0 - 15)");
+
+static int modparam_long_retry = B43_DEFAULT_LONG_RETRY_LIMIT;
+module_param_named(long_retry, modparam_long_retry, int, 0444);
+MODULE_PARM_DESC(long_retry, "Long-Retry-Limit (0 - 15)");
+
+static int modparam_noleds;
+module_param_named(noleds, modparam_noleds, int, 0444);
+MODULE_PARM_DESC(noleds, "Turn off all LED activity");
+
+static char modparam_fwpostfix[16];
+module_param_string(fwpostfix, modparam_fwpostfix, 16, 0444);
+MODULE_PARM_DESC(fwpostfix, "Postfix for the .fw files to load.");
+
+static int modparam_mon_keep_bad;
+module_param_named(mon_keep_bad, modparam_mon_keep_bad, int, 0444);
+MODULE_PARM_DESC(mon_keep_bad, "Keep bad frames in monitor mode");
+
+static int modparam_mon_keep_badplcp;
+module_param_named(mon_keep_badplcp, modparam_mon_keep_bad, int, 0444);
+MODULE_PARM_DESC(mon_keep_badplcp, "Keep frames with bad PLCP in monitor mode");
+
+static int modparam_hwpctl;
+module_param_named(hwpctl, modparam_hwpctl, int, 0444);
+MODULE_PARM_DESC(hwpctl, "Enable hardware-side power control (default off)");
+
+static int modparam_nohwcrypt;
+module_param_named(nohwcrypt, modparam_nohwcrypt, int, 0444);
+MODULE_PARM_DESC(nohwcrypt, "Disable hardware encryption.");
+
+static const struct ssb_device_id b43_ssb_tbl[] = {
+ SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_80211, 5),
+ SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_80211, 6),
+ SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_80211, 7),
+ SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_80211, 9),
+ SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_80211, 10),
+ SSB_DEVTABLE_END
+};
+
+MODULE_DEVICE_TABLE(ssb, b43_ssb_tbl);
+
+/* Channel and ratetables are shared for all devices.
+ * They can't be const, because ieee80211 puts some precalculated
+ * data in there. This data is the same for all devices, so we don't
+ * get concurrency issues */
+#define RATETAB_ENT(_rateid, _flags) \
+ { \
+ .rate = B43_RATE_TO_BASE100KBPS(_rateid), \
+ .val = (_rateid), \
+ .val2 = (_rateid), \
+ .flags = (_flags), \
+ }
+static struct ieee80211_rate __b43_ratetable[] = {
+ RATETAB_ENT(B43_CCK_RATE_1MB, IEEE80211_RATE_CCK),
+ RATETAB_ENT(B43_CCK_RATE_2MB, IEEE80211_RATE_CCK_2),
+ RATETAB_ENT(B43_CCK_RATE_5MB, IEEE80211_RATE_CCK_2),
+ RATETAB_ENT(B43_CCK_RATE_11MB, IEEE80211_RATE_CCK_2),
+ RATETAB_ENT(B43_OFDM_RATE_6MB, IEEE80211_RATE_OFDM),
+ RATETAB_ENT(B43_OFDM_RATE_9MB, IEEE80211_RATE_OFDM),
+ RATETAB_ENT(B43_OFDM_RATE_12MB, IEEE80211_RATE_OFDM),
+ RATETAB_ENT(B43_OFDM_RATE_18MB, IEEE80211_RATE_OFDM),
+ RATETAB_ENT(B43_OFDM_RATE_24MB, IEEE80211_RATE_OFDM),
+ RATETAB_ENT(B43_OFDM_RATE_36MB, IEEE80211_RATE_OFDM),
+ RATETAB_ENT(B43_OFDM_RATE_48MB, IEEE80211_RATE_OFDM),
+ RATETAB_ENT(B43_OFDM_RATE_54MB, IEEE80211_RATE_OFDM),
+};
+
+#define b43_a_ratetable (__b43_ratetable + 4)
+#define b43_a_ratetable_size 8
+#define b43_b_ratetable (__b43_ratetable + 0)
+#define b43_b_ratetable_size 4
+#define b43_g_ratetable (__b43_ratetable + 0)
+#define b43_g_ratetable_size 12
+
+#define CHANTAB_ENT(_chanid, _freq) \
+ { \
+ .chan = (_chanid), \
+ .freq = (_freq), \
+ .val = (_chanid), \
+ .flag = IEEE80211_CHAN_W_SCAN | \
+ IEEE80211_CHAN_W_ACTIVE_SCAN | \
+ IEEE80211_CHAN_W_IBSS, \
+ .power_level = 0xFF, \
+ .antenna_max = 0xFF, \
+ }
+static struct ieee80211_channel b43_bg_chantable[] = {
+ CHANTAB_ENT(1, 2412),
+ CHANTAB_ENT(2, 2417),
+ CHANTAB_ENT(3, 2422),
+ CHANTAB_ENT(4, 2427),
+ CHANTAB_ENT(5, 2432),
+ CHANTAB_ENT(6, 2437),
+ CHANTAB_ENT(7, 2442),
+ CHANTAB_ENT(8, 2447),
+ CHANTAB_ENT(9, 2452),
+ CHANTAB_ENT(10, 2457),
+ CHANTAB_ENT(11, 2462),
+ CHANTAB_ENT(12, 2467),
+ CHANTAB_ENT(13, 2472),
+ CHANTAB_ENT(14, 2484),
+};
+
+#define b43_bg_chantable_size ARRAY_SIZE(b43_bg_chantable)
+static struct ieee80211_channel b43_a_chantable[] = {
+ CHANTAB_ENT(36, 5180),
+ CHANTAB_ENT(40, 5200),
+ CHANTAB_ENT(44, 5220),
+ CHANTAB_ENT(48, 5240),
+ CHANTAB_ENT(52, 5260),
+ CHANTAB_ENT(56, 5280),
+ CHANTAB_ENT(60, 5300),
+ CHANTAB_ENT(64, 5320),
+ CHANTAB_ENT(149, 5745),
+ CHANTAB_ENT(153, 5765),
+ CHANTAB_ENT(157, 5785),
+ CHANTAB_ENT(161, 5805),
+ CHANTAB_ENT(165, 5825),
+};
+
+#define b43_a_chantable_size ARRAY_SIZE(b43_a_chantable)
+
+static void b43_wireless_core_exit(struct b43_wldev *dev);
+static int b43_wireless_core_init(struct b43_wldev *dev);
+static void b43_wireless_core_stop(struct b43_wldev *dev);
+static int b43_wireless_core_start(struct b43_wldev *dev);
+
+static int b43_ratelimit(struct b43_wl *wl)
+{
+ if (!wl || !wl->current_dev)
+ return 1;
+ if (b43_status(wl->current_dev) < B43_STAT_STARTED)
+ return 1;
+ /* We are up and running.
+ * Ratelimit the messages to avoid DoS over the net. */
+ return net_ratelimit();
+}
+
+void b43info(struct b43_wl *wl, const char *fmt, ...)
+{
+ va_list args;
+
+ if (!b43_ratelimit(wl))
+ return;
+ va_start(args, fmt);
+ printk(KERN_INFO "b43-%s: ",
+ (wl && wl->hw) ? wiphy_name(wl->hw->wiphy) : "wlan");
+ vprintk(fmt, args);
+ va_end(args);
+}
+
+void b43err(struct b43_wl *wl, const char *fmt, ...)
+{
+ va_list args;
+
+ if (!b43_ratelimit(wl))
+ return;
+ va_start(args, fmt);
+ printk(KERN_ERR "b43-%s ERROR: ",
+ (wl && wl->hw) ? wiphy_name(wl->hw->wiphy) : "wlan");
+ vprintk(fmt, args);
+ va_end(args);
+}
+
+void b43warn(struct b43_wl *wl, const char *fmt, ...)
+{
+ va_list args;
+
+ if (!b43_ratelimit(wl))
+ return;
+ va_start(args, fmt);
+ printk(KERN_WARNING "b43-%s warning: ",
+ (wl && wl->hw) ? wiphy_name(wl->hw->wiphy) : "wlan");
+ vprintk(fmt, args);
+ va_end(args);
+}
+
+#if B43_DEBUG
+void b43dbg(struct b43_wl *wl, const char *fmt, ...)
+{
+ va_list args;
+
+ va_start(args, fmt);
+ printk(KERN_DEBUG "b43-%s debug: ",
+ (wl && wl->hw) ? wiphy_name(wl->hw->wiphy) : "wlan");
+ vprintk(fmt, args);
+ va_end(args);
+}
+#endif /* DEBUG */
+
+static void b43_ram_write(struct b43_wldev *dev, u16 offset, u32 val)
+{
+ u32 macctl;
+
+ B43_WARN_ON(offset % 4 != 0);
+
+ macctl = b43_read32(dev, B43_MMIO_MACCTL);
+ if (macctl & B43_MACCTL_BE)
+ val = swab32(val);
+
+ b43_write32(dev, B43_MMIO_RAM_CONTROL, offset);
+ mmiowb();
+ b43_write32(dev, B43_MMIO_RAM_DATA, val);
+}
+
+static inline
+ void b43_shm_control_word(struct b43_wldev *dev, u16 routing, u16 offset)
+{
+ u32 control;
+
+ /* "offset" is the WORD offset. */
+
+ control = routing;
+ control <<= 16;
+ control |= offset;
+ b43_write32(dev, B43_MMIO_SHM_CONTROL, control);
+}
+
+u32 b43_shm_read32(struct b43_wldev *dev, u16 routing, u16 offset)
+{
+ u32 ret;
+
+ if (routing == B43_SHM_SHARED) {
+ B43_WARN_ON(offset & 0x0001);
+ if (offset & 0x0003) {
+ /* Unaligned access */
+ b43_shm_control_word(dev, routing, offset >> 2);
+ ret = b43_read16(dev, B43_MMIO_SHM_DATA_UNALIGNED);
+ ret <<= 16;
+ b43_shm_control_word(dev, routing, (offset >> 2) + 1);
+ ret |= b43_read16(dev, B43_MMIO_SHM_DATA);
+
+ return ret;
+ }
+ offset >>= 2;
+ }
+ b43_shm_control_word(dev, routing, offset);
+ ret = b43_read32(dev, B43_MMIO_SHM_DATA);
+
+ return ret;
+}
+
+u16 b43_shm_read16(struct b43_wldev * dev, u16 routing, u16 offset)
+{
+ u16 ret;
+
+ if (routing == B43_SHM_SHARED) {
+ B43_WARN_ON(offset & 0x0001);
+ if (offset & 0x0003) {
+ /* Unaligned access */
+ b43_shm_control_word(dev, routing, offset >> 2);
+ ret = b43_read16(dev, B43_MMIO_SHM_DATA_UNALIGNED);
+
+ return ret;
+ }
+ offset >>= 2;
+ }
+ b43_shm_control_word(dev, routing, offset);
+ ret = b43_read16(dev, B43_MMIO_SHM_DATA);
+
+ return ret;
+}
+
+void b43_shm_write32(struct b43_wldev *dev, u16 routing, u16 offset, u32 value)
+{
+ if (routing == B43_SHM_SHARED) {
+ B43_WARN_ON(offset & 0x0001);
+ if (offset & 0x0003) {
+ /* Unaligned access */
+ b43_shm_control_word(dev, routing, offset >> 2);
+ mmiowb();
+ b43_write16(dev, B43_MMIO_SHM_DATA_UNALIGNED,
+ (value >> 16) & 0xffff);
+ mmiowb();
+ b43_shm_control_word(dev, routing, (offset >> 2) + 1);
+ mmiowb();
+ b43_write16(dev, B43_MMIO_SHM_DATA, value & 0xffff);
+ return;
+ }
+ offset >>= 2;
+ }
+ b43_shm_control_word(dev, routing, offset);
+ mmiowb();
+ b43_write32(dev, B43_MMIO_SHM_DATA, value);
+}
+
+void b43_shm_write16(struct b43_wldev *dev, u16 routing, u16 offset, u16 value)
+{
+ if (routing == B43_SHM_SHARED) {
+ B43_WARN_ON(offset & 0x0001);
+ if (offset & 0x0003) {
+ /* Unaligned access */
+ b43_shm_control_word(dev, routing, offset >> 2);
+ mmiowb();
+ b43_write16(dev, B43_MMIO_SHM_DATA_UNALIGNED, value);
+ return;
+ }
+ offset >>= 2;
+ }
+ b43_shm_control_word(dev, routing, offset);
+ mmiowb();
+ b43_write16(dev, B43_MMIO_SHM_DATA, value);
+}
+
+/* Read HostFlags */
+u32 b43_hf_read(struct b43_wldev * dev)
+{
+ u32 ret;
+
+ ret = b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_HOSTFHI);
+ ret <<= 16;
+ ret |= b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_HOSTFLO);
+
+ return ret;
+}
+
+/* Write HostFlags */
+void b43_hf_write(struct b43_wldev *dev, u32 value)
+{
+ b43_shm_write16(dev, B43_SHM_SHARED,
+ B43_SHM_SH_HOSTFLO, (value & 0x0000FFFF));
+ b43_shm_write16(dev, B43_SHM_SHARED,
+ B43_SHM_SH_HOSTFHI, ((value & 0xFFFF0000) >> 16));
+}
+
+void b43_tsf_read(struct b43_wldev *dev, u64 * tsf)
+{
+ /* We need to be careful. As we read the TSF from multiple
+ * registers, we should take care of register overflows.
+ * In theory, the whole tsf read process should be atomic.
+ * We try to be atomic here, by restaring the read process,
+ * if any of the high registers changed (overflew).
+ */
+ if (dev->dev->id.revision >= 3) {
+ u32 low, high, high2;
+
+ do {
+ high = b43_read32(dev, B43_MMIO_REV3PLUS_TSF_HIGH);
+ low = b43_read32(dev, B43_MMIO_REV3PLUS_TSF_LOW);
+ high2 = b43_read32(dev, B43_MMIO_REV3PLUS_TSF_HIGH);
+ } while (unlikely(high != high2));
+
+ *tsf = high;
+ *tsf <<= 32;
+ *tsf |= low;
+ } else {
+ u64 tmp;
+ u16 v0, v1, v2, v3;
+ u16 test1, test2, test3;
+
+ do {
+ v3 = b43_read16(dev, B43_MMIO_TSF_3);
+ v2 = b43_read16(dev, B43_MMIO_TSF_2);
+ v1 = b43_read16(dev, B43_MMIO_TSF_1);
+ v0 = b43_read16(dev, B43_MMIO_TSF_0);
+
+ test3 = b43_read16(dev, B43_MMIO_TSF_3);
+ test2 = b43_read16(dev, B43_MMIO_TSF_2);
+ test1 = b43_read16(dev, B43_MMIO_TSF_1);
+ } while (v3 != test3 || v2 != test2 || v1 != test1);
+
+ *tsf = v3;
+ *tsf <<= 48;
+ tmp = v2;
+ tmp <<= 32;
+ *tsf |= tmp;
+ tmp = v1;
+ tmp <<= 16;
+ *tsf |= tmp;
+ *tsf |= v0;
+ }
+}
+
+static void b43_time_lock(struct b43_wldev *dev)
+{
+ u32 macctl;
+
+ macctl = b43_read32(dev, B43_MMIO_MACCTL);
+ macctl |= B43_MACCTL_TBTTHOLD;
+ b43_write32(dev, B43_MMIO_MACCTL, macctl);
+ /* Commit the write */
+ b43_read32(dev, B43_MMIO_MACCTL);
+}
+
+static void b43_time_unlock(struct b43_wldev *dev)
+{
+ u32 macctl;
+
+ macctl = b43_read32(dev, B43_MMIO_MACCTL);
+ macctl &= ~B43_MACCTL_TBTTHOLD;
+ b43_write32(dev, B43_MMIO_MACCTL, macctl);
+ /* Commit the write */
+ b43_read32(dev, B43_MMIO_MACCTL);
+}
+
+static void b43_tsf_write_locked(struct b43_wldev *dev, u64 tsf)
+{
+ /* Be careful with the in-progress timer.
+ * First zero out the low register, so we have a full
+ * register-overflow duration to complete the operation.
+ */
+ if (dev->dev->id.revision >= 3) {
+ u32 lo = (tsf & 0x00000000FFFFFFFFULL);
+ u32 hi = (tsf & 0xFFFFFFFF00000000ULL) >> 32;
+
+ b43_write32(dev, B43_MMIO_REV3PLUS_TSF_LOW, 0);
+ mmiowb();
+ b43_write32(dev, B43_MMIO_REV3PLUS_TSF_HIGH, hi);
+ mmiowb();
+ b43_write32(dev, B43_MMIO_REV3PLUS_TSF_LOW, lo);
+ } else {
+ u16 v0 = (tsf & 0x000000000000FFFFULL);
+ u16 v1 = (tsf & 0x00000000FFFF0000ULL) >> 16;
+ u16 v2 = (tsf & 0x0000FFFF00000000ULL) >> 32;
+ u16 v3 = (tsf & 0xFFFF000000000000ULL) >> 48;
+
+ b43_write16(dev, B43_MMIO_TSF_0, 0);
+ mmiowb();
+ b43_write16(dev, B43_MMIO_TSF_3, v3);
+ mmiowb();
+ b43_write16(dev, B43_MMIO_TSF_2, v2);
+ mmiowb();
+ b43_write16(dev, B43_MMIO_TSF_1, v1);
+ mmiowb();
+ b43_write16(dev, B43_MMIO_TSF_0, v0);
+ }
+}
+
+void b43_tsf_write(struct b43_wldev *dev, u64 tsf)
+{
+ b43_time_lock(dev);
+ b43_tsf_write_locked(dev, tsf);
+ b43_time_unlock(dev);
+}
+
+static
+void b43_macfilter_set(struct b43_wldev *dev, u16 offset, const u8 * mac)
+{
+ static const u8 zero_addr[ETH_ALEN] = { 0 };
+ u16 data;
+
+ if (!mac)
+ mac = zero_addr;
+
+ offset |= 0x0020;
+ b43_write16(dev, B43_MMIO_MACFILTER_CONTROL, offset);
+
+ data = mac[0];
+ data |= mac[1] << 8;
+ b43_write16(dev, B43_MMIO_MACFILTER_DATA, data);
+ data = mac[2];
+ data |= mac[3] << 8;
+ b43_write16(dev, B43_MMIO_MACFILTER_DATA, data);
+ data = mac[4];
+ data |= mac[5] << 8;
+ b43_write16(dev, B43_MMIO_MACFILTER_DATA, data);
+}
+
+static void b43_write_mac_bssid_templates(struct b43_wldev *dev)
+{
+ const u8 *mac;
+ const u8 *bssid;
+ u8 mac_bssid[ETH_ALEN * 2];
+ int i;
+ u32 tmp;
+
+ bssid = dev->wl->bssid;
+ mac = dev->wl->mac_addr;
+
+ b43_macfilter_set(dev, B43_MACFILTER_BSSID, bssid);
+
+ memcpy(mac_bssid, mac, ETH_ALEN);
+ memcpy(mac_bssid + ETH_ALEN, bssid, ETH_ALEN);
+
+ /* Write our MAC address and BSSID to template ram */
+ for (i = 0; i < ARRAY_SIZE(mac_bssid); i += sizeof(u32)) {
+ tmp = (u32) (mac_bssid[i + 0]);
+ tmp |= (u32) (mac_bssid[i + 1]) << 8;
+ tmp |= (u32) (mac_bssid[i + 2]) << 16;
+ tmp |= (u32) (mac_bssid[i + 3]) << 24;
+ b43_ram_write(dev, 0x20 + i, tmp);
+ }
+}
+
+static void b43_upload_card_macaddress(struct b43_wldev *dev,
+ const u8 * mac_addr)
+{
+ if (mac_addr)
+ memcpy(dev->wl->mac_addr, mac_addr, ETH_ALEN);
+ else
+ memset(dev->wl->mac_addr, 0, ETH_ALEN);
+ b43_write_mac_bssid_templates(dev);
+ b43_macfilter_set(dev, B43_MACFILTER_SELF, mac_addr);
+}
+
+static void b43_set_slot_time(struct b43_wldev *dev, u16 slot_time)
+{
+ /* slot_time is in usec. */
+ if (dev->phy.type != B43_PHYTYPE_G)
+ return;
+ b43_write16(dev, 0x684, 510 + slot_time);
+ b43_shm_write16(dev, B43_SHM_SHARED, 0x0010, slot_time);
+}
+
+static void b43_short_slot_timing_enable(struct b43_wldev *dev)
+{
+ b43_set_slot_time(dev, 9);
+ dev->short_slot = 1;
+}
+
+static void b43_short_slot_timing_disable(struct b43_wldev *dev)
+{
+ b43_set_slot_time(dev, 20);
+ dev->short_slot = 0;
+}
+
+/* Enable a Generic IRQ. "mask" is the mask of which IRQs to enable.
+ * Returns the _previously_ enabled IRQ mask.
+ */
+static inline u32 b43_interrupt_enable(struct b43_wldev *dev, u32 mask)
+{
+ u32 old_mask;
+
+ old_mask = b43_read32(dev, B43_MMIO_GEN_IRQ_MASK);
+ b43_write32(dev, B43_MMIO_GEN_IRQ_MASK, old_mask | mask);
+
+ return old_mask;
+}
+
+/* Disable a Generic IRQ. "mask" is the mask of which IRQs to disable.
+ * Returns the _previously_ enabled IRQ mask.
+ */
+static inline u32 b43_interrupt_disable(struct b43_wldev *dev, u32 mask)
+{
+ u32 old_mask;
+
+ old_mask = b43_read32(dev, B43_MMIO_GEN_IRQ_MASK);
+ b43_write32(dev, B43_MMIO_GEN_IRQ_MASK, old_mask & ~mask);
+
+ return old_mask;
+}
+
+/* Synchronize IRQ top- and bottom-half.
+ * IRQs must be masked before calling this.
+ * This must not be called with the irq_lock held.
+ */
+static void b43_synchronize_irq(struct b43_wldev *dev)
+{
+ synchronize_irq(dev->dev->irq);
+ tasklet_kill(&dev->isr_tasklet);
+}
+
+/* DummyTransmission function, as documented on
+ * http://bcm-specs.sipsolutions.net/DummyTransmission
+ */
+void b43_dummy_transmission(struct b43_wldev *dev)
+{
+ struct b43_phy *phy = &dev->phy;
+ unsigned int i, max_loop;
+ u16 value;
+ u32 buffer[5] = {
+ 0x00000000,
+ 0x00D40000,
+ 0x00000000,
+ 0x01000000,
+ 0x00000000,
+ };
+
+ switch (phy->type) {
+ case B43_PHYTYPE_A:
+ max_loop = 0x1E;
+ buffer[0] = 0x000201CC;
+ break;
+ case B43_PHYTYPE_B:
+ case B43_PHYTYPE_G:
+ max_loop = 0xFA;
+ buffer[0] = 0x000B846E;
+ break;
+ default:
+ B43_WARN_ON(1);
+ return;
+ }
+
+ for (i = 0; i < 5; i++)
+ b43_ram_write(dev, i * 4, buffer[i]);
+
+ /* Commit writes */
+ b43_read32(dev, B43_MMIO_MACCTL);
+
+ b43_write16(dev, 0x0568, 0x0000);
+ b43_write16(dev, 0x07C0, 0x0000);
+ value = ((phy->type == B43_PHYTYPE_A) ? 1 : 0);
+ b43_write16(dev, 0x050C, value);
+ b43_write16(dev, 0x0508, 0x0000);
+ b43_write16(dev, 0x050A, 0x0000);
+ b43_write16(dev, 0x054C, 0x0000);
+ b43_write16(dev, 0x056A, 0x0014);
+ b43_write16(dev, 0x0568, 0x0826);
+ b43_write16(dev, 0x0500, 0x0000);
+ b43_write16(dev, 0x0502, 0x0030);
+
+ if (phy->radio_ver == 0x2050 && phy->radio_rev <= 0x5)
+ b43_radio_write16(dev, 0x0051, 0x0017);
+ for (i = 0x00; i < max_loop; i++) {
+ value = b43_read16(dev, 0x050E);
+ if (value & 0x0080)
+ break;
+ udelay(10);
+ }
+ for (i = 0x00; i < 0x0A; i++) {
+ value = b43_read16(dev, 0x050E);
+ if (value & 0x0400)
+ break;
+ udelay(10);
+ }
+ for (i = 0x00; i < 0x0A; i++) {
+ value = b43_read16(dev, 0x0690);
+ if (!(value & 0x0100))
+ break;
+ udelay(10);
+ }
+ if (phy->radio_ver == 0x2050 && phy->radio_rev <= 0x5)
+ b43_radio_write16(dev, 0x0051, 0x0037);
+}
+
+static void key_write(struct b43_wldev *dev,
+ u8 index, u8 algorithm, const u8 * key)
+{
+ unsigned int i;
+ u32 offset;
+ u16 value;
+ u16 kidx;
+
+ /* Key index/algo block */
+ kidx = b43_kidx_to_fw(dev, index);
+ value = ((kidx << 4) | algorithm);
+ b43_shm_write16(dev, B43_SHM_SHARED,
+ B43_SHM_SH_KEYIDXBLOCK + (kidx * 2), value);
+
+ /* Write the key to the Key Table Pointer offset */
+ offset = dev->ktp + (index * B43_SEC_KEYSIZE);
+ for (i = 0; i < B43_SEC_KEYSIZE; i += 2) {
+ value = key[i];
+ value |= (u16) (key[i + 1]) << 8;
+ b43_shm_write16(dev, B43_SHM_SHARED, offset + i, value);
+ }
+}
+
+static void keymac_write(struct b43_wldev *dev, u8 index, const u8 * addr)
+{
+ u32 addrtmp[2] = { 0, 0, };
+ u8 per_sta_keys_start = 8;
+
+ if (b43_new_kidx_api(dev))
+ per_sta_keys_start = 4;
+
+ B43_WARN_ON(index < per_sta_keys_start);
+ /* We have two default TX keys and possibly two default RX keys.
+ * Physical mac 0 is mapped to physical key 4 or 8, depending
+ * on the firmware version.
+ * So we must adjust the index here.
+ */
+ index -= per_sta_keys_start;
+
+ if (addr) {
+ addrtmp[0] = addr[0];
+ addrtmp[0] |= ((u32) (addr[1]) << 8);
+ addrtmp[0] |= ((u32) (addr[2]) << 16);
+ addrtmp[0] |= ((u32) (addr[3]) << 24);
+ addrtmp[1] = addr[4];
+ addrtmp[1] |= ((u32) (addr[5]) << 8);
+ }
+
+ if (dev->dev->id.revision >= 5) {
+ /* Receive match transmitter address mechanism */
+ b43_shm_write32(dev, B43_SHM_RCMTA,
+ (index * 2) + 0, addrtmp[0]);
+ b43_shm_write16(dev, B43_SHM_RCMTA,
+ (index * 2) + 1, addrtmp[1]);
+ } else {
+ /* RXE (Receive Engine) and
+ * PSM (Programmable State Machine) mechanism
+ */
+ if (index < 8) {
+ /* TODO write to RCM 16, 19, 22 and 25 */
+ } else {
+ b43_shm_write32(dev, B43_SHM_SHARED,
+ B43_SHM_SH_PSM + (index * 6) + 0,
+ addrtmp[0]);
+ b43_shm_write16(dev, B43_SHM_SHARED,
+ B43_SHM_SH_PSM + (index * 6) + 4,
+ addrtmp[1]);
+ }
+ }
+}
+
+static void do_key_write(struct b43_wldev *dev,
+ u8 index, u8 algorithm,
+ const u8 * key, size_t key_len, const u8 * mac_addr)
+{
+ u8 buf[B43_SEC_KEYSIZE] = { 0, };
+ u8 per_sta_keys_start = 8;
+
+ if (b43_new_kidx_api(dev))
+ per_sta_keys_start = 4;
+
+ B43_WARN_ON(index >= dev->max_nr_keys);
+ B43_WARN_ON(key_len > B43_SEC_KEYSIZE);
+
+ if (index >= per_sta_keys_start)
+ keymac_write(dev, index, NULL); /* First zero out mac. */
+ if (key)
+ memcpy(buf, key, key_len);
+ key_write(dev, index, algorithm, buf);
+ if (index >= per_sta_keys_start)
+ keymac_write(dev, index, mac_addr);
+
+ dev->key[index].algorithm = algorithm;
+}
+
+static int b43_key_write(struct b43_wldev *dev,
+ int index, u8 algorithm,
+ const u8 * key, size_t key_len,
+ const u8 * mac_addr,
+ struct ieee80211_key_conf *keyconf)
+{
+ int i;
+ int sta_keys_start;
+
+ if (key_len > B43_SEC_KEYSIZE)
+ return -EINVAL;
+ for (i = 0; i < dev->max_nr_keys; i++) {
+ /* Check that we don't already have this key. */
+ B43_WARN_ON(dev->key[i].keyconf == keyconf);
+ }
+ if (index < 0) {
+ /* Either pairwise key or address is 00:00:00:00:00:00
+ * for transmit-only keys. Search the index. */
+ if (b43_new_kidx_api(dev))
+ sta_keys_start = 4;
+ else
+ sta_keys_start = 8;
+ for (i = sta_keys_start; i < dev->max_nr_keys; i++) {
+ if (!dev->key[i].keyconf) {
+ /* found empty */
+ index = i;
+ break;
+ }
+ }
+ if (index < 0) {
+ b43err(dev->wl, "Out of hardware key memory\n");
+ return -ENOSPC;
+ }
+ } else
+ B43_WARN_ON(index > 3);
+
+ do_key_write(dev, index, algorithm, key, key_len, mac_addr);
+ if ((index <= 3) && !b43_new_kidx_api(dev)) {
+ /* Default RX key */
+ B43_WARN_ON(mac_addr);
+ do_key_write(dev, index + 4, algorithm, key, key_len, NULL);
+ }
+ keyconf->hw_key_idx = index;
+ dev->key[index].keyconf = keyconf;
+
+ return 0;
+}
+
+static int b43_key_clear(struct b43_wldev *dev, int index)
+{
+ if (B43_WARN_ON((index < 0) || (index >= dev->max_nr_keys)))
+ return -EINVAL;
+ do_key_write(dev, index, B43_SEC_ALGO_NONE,
+ NULL, B43_SEC_KEYSIZE, NULL);
+ if ((index <= 3) && !b43_new_kidx_api(dev)) {
+ do_key_write(dev, index + 4, B43_SEC_ALGO_NONE,
+ NULL, B43_SEC_KEYSIZE, NULL);
+ }
+ dev->key[index].keyconf = NULL;
+
+ return 0;
+}
+
+static void b43_clear_keys(struct b43_wldev *dev)
+{
+ int i;
+
+ for (i = 0; i < dev->max_nr_keys; i++)
+ b43_key_clear(dev, i);
+}
+
+void b43_power_saving_ctl_bits(struct b43_wldev *dev, unsigned int ps_flags)
+{
+ u32 macctl;
+ u16 ucstat;
+ bool hwps;
+ bool awake;
+ int i;
+
+ B43_WARN_ON((ps_flags & B43_PS_ENABLED) &&
+ (ps_flags & B43_PS_DISABLED));
+ B43_WARN_ON((ps_flags & B43_PS_AWAKE) && (ps_flags & B43_PS_ASLEEP));
+
+ if (ps_flags & B43_PS_ENABLED) {
+ hwps = 1;
+ } else if (ps_flags & B43_PS_DISABLED) {
+ hwps = 0;
+ } else {
+ //TODO: If powersave is not off and FIXME is not set and we are not in adhoc
+ // and thus is not an AP and we are associated, set bit 25
+ }
+ if (ps_flags & B43_PS_AWAKE) {
+ awake = 1;
+ } else if (ps_flags & B43_PS_ASLEEP) {
+ awake = 0;
+ } else {
+ //TODO: If the device is awake or this is an AP, or we are scanning, or FIXME,
+ // or we are associated, or FIXME, or the latest PS-Poll packet sent was
+ // successful, set bit26
+ }
+
+/* FIXME: For now we force awake-on and hwps-off */
+ hwps = 0;
+ awake = 1;
+
+ macctl = b43_read32(dev, B43_MMIO_MACCTL);
+ if (hwps)
+ macctl |= B43_MACCTL_HWPS;
+ else
+ macctl &= ~B43_MACCTL_HWPS;
+ if (awake)
+ macctl |= B43_MACCTL_AWAKE;
+ else
+ macctl &= ~B43_MACCTL_AWAKE;
+ b43_write32(dev, B43_MMIO_MACCTL, macctl);
+ /* Commit write */
+ b43_read32(dev, B43_MMIO_MACCTL);
+ if (awake && dev->dev->id.revision >= 5) {
+ /* Wait for the microcode to wake up. */
+ for (i = 0; i < 100; i++) {
+ ucstat = b43_shm_read16(dev, B43_SHM_SHARED,
+ B43_SHM_SH_UCODESTAT);
+ if (ucstat != B43_SHM_SH_UCODESTAT_SLEEP)
+ break;
+ udelay(10);
+ }
+ }
+}
+
+/* Turn the Analog ON/OFF */
+static void b43_switch_analog(struct b43_wldev *dev, int on)
+{
+ b43_write16(dev, B43_MMIO_PHY0, on ? 0 : 0xF4);
+}
+
+void b43_wireless_core_reset(struct b43_wldev *dev, u32 flags)
+{
+ u32 tmslow;
+ u32 macctl;
+
+ flags |= B43_TMSLOW_PHYCLKEN;
+ flags |= B43_TMSLOW_PHYRESET;
+ ssb_device_enable(dev->dev, flags);
+ msleep(2); /* Wait for the PLL to turn on. */
+
+ /* Now take the PHY out of Reset again */
+ tmslow = ssb_read32(dev->dev, SSB_TMSLOW);
+ tmslow |= SSB_TMSLOW_FGC;
+ tmslow &= ~B43_TMSLOW_PHYRESET;
+ ssb_write32(dev->dev, SSB_TMSLOW, tmslow);
+ ssb_read32(dev->dev, SSB_TMSLOW); /* flush */
+ msleep(1);
+ tmslow &= ~SSB_TMSLOW_FGC;
+ ssb_write32(dev->dev, SSB_TMSLOW, tmslow);
+ ssb_read32(dev->dev, SSB_TMSLOW); /* flush */
+ msleep(1);
+
+ /* Turn Analog ON */
+ b43_switch_analog(dev, 1);
+
+ macctl = b43_read32(dev, B43_MMIO_MACCTL);
+ macctl &= ~B43_MACCTL_GMODE;
+ if (flags & B43_TMSLOW_GMODE)
+ macctl |= B43_MACCTL_GMODE;
+ macctl |= B43_MACCTL_IHR_ENABLED;
+ b43_write32(dev, B43_MMIO_MACCTL, macctl);
+}
+
+static void handle_irq_transmit_status(struct b43_wldev *dev)
+{
+ u32 v0, v1;
+ u16 tmp;
+ struct b43_txstatus stat;
+
+ while (1) {
+ v0 = b43_read32(dev, B43_MMIO_XMITSTAT_0);
+ if (!(v0 & 0x00000001))
+ break;
+ v1 = b43_read32(dev, B43_MMIO_XMITSTAT_1);
+
+ stat.cookie = (v0 >> 16);
+ stat.seq = (v1 & 0x0000FFFF);
+ stat.phy_stat = ((v1 & 0x00FF0000) >> 16);
+ tmp = (v0 & 0x0000FFFF);
+ stat.frame_count = ((tmp & 0xF000) >> 12);
+ stat.rts_count = ((tmp & 0x0F00) >> 8);
+ stat.supp_reason = ((tmp & 0x001C) >> 2);
+ stat.pm_indicated = !!(tmp & 0x0080);
+ stat.intermediate = !!(tmp & 0x0040);
+ stat.for_ampdu = !!(tmp & 0x0020);
+ stat.acked = !!(tmp & 0x0002);
+
+ b43_handle_txstatus(dev, &stat);
+ }
+}
+
+static void drain_txstatus_queue(struct b43_wldev *dev)
+{
+ u32 dummy;
+
+ if (dev->dev->id.revision < 5)
+ return;
+ /* Read all entries from the microcode TXstatus FIFO
+ * and throw them away.
+ */
+ while (1) {
+ dummy = b43_read32(dev, B43_MMIO_XMITSTAT_0);
+ if (!(dummy & 0x00000001))
+ break;
+ dummy = b43_read32(dev, B43_MMIO_XMITSTAT_1);
+ }
+}
+
+static u32 b43_jssi_read(struct b43_wldev *dev)
+{
+ u32 val = 0;
+
+ val = b43_shm_read16(dev, B43_SHM_SHARED, 0x08A);
+ val <<= 16;
+ val |= b43_shm_read16(dev, B43_SHM_SHARED, 0x088);
+
+ return val;
+}
+
+static void b43_jssi_write(struct b43_wldev *dev, u32 jssi)
+{
+ b43_shm_write16(dev, B43_SHM_SHARED, 0x088, (jssi & 0x0000FFFF));
+ b43_shm_write16(dev, B43_SHM_SHARED, 0x08A, (jssi & 0xFFFF0000) >> 16);
+}
+
+static void b43_generate_noise_sample(struct b43_wldev *dev)
+{
+ b43_jssi_write(dev, 0x7F7F7F7F);
+ b43_write32(dev, B43_MMIO_STATUS2_BITFIELD,
+ b43_read32(dev, B43_MMIO_STATUS2_BITFIELD)
+ | (1 << 4));
+ B43_WARN_ON(dev->noisecalc.channel_at_start != dev->phy.channel);
+}
+
+static void b43_calculate_link_quality(struct b43_wldev *dev)
+{
+ /* Top half of Link Quality calculation. */
+
+ if (dev->noisecalc.calculation_running)
+ return;
+ dev->noisecalc.channel_at_start = dev->phy.channel;
+ dev->noisecalc.calculation_running = 1;
+ dev->noisecalc.nr_samples = 0;
+
+ b43_generate_noise_sample(dev);
+}
+
+static void handle_irq_noise(struct b43_wldev *dev)
+{
+ struct b43_phy *phy = &dev->phy;
+ u16 tmp;
+ u8 noise[4];
+ u8 i, j;
+ s32 average;
+
+ /* Bottom half of Link Quality calculation. */
+
+ B43_WARN_ON(!dev->noisecalc.calculation_running);
+ if (dev->noisecalc.channel_at_start != phy->channel)
+ goto drop_calculation;
+ *((u32 *) noise) = cpu_to_le32(b43_jssi_read(dev));
+ if (noise[0] == 0x7F || noise[1] == 0x7F ||
+ noise[2] == 0x7F || noise[3] == 0x7F)
+ goto generate_new;
+
+ /* Get the noise samples. */
+ B43_WARN_ON(dev->noisecalc.nr_samples >= 8);
+ i = dev->noisecalc.nr_samples;
+ noise[0] = limit_value(noise[0], 0, ARRAY_SIZE(phy->nrssi_lt) - 1);
+ noise[1] = limit_value(noise[1], 0, ARRAY_SIZE(phy->nrssi_lt) - 1);
+ noise[2] = limit_value(noise[2], 0, ARRAY_SIZE(phy->nrssi_lt) - 1);
+ noise[3] = limit_value(noise[3], 0, ARRAY_SIZE(phy->nrssi_lt) - 1);
+ dev->noisecalc.samples[i][0] = phy->nrssi_lt[noise[0]];
+ dev->noisecalc.samples[i][1] = phy->nrssi_lt[noise[1]];
+ dev->noisecalc.samples[i][2] = phy->nrssi_lt[noise[2]];
+ dev->noisecalc.samples[i][3] = phy->nrssi_lt[noise[3]];
+ dev->noisecalc.nr_samples++;
+ if (dev->noisecalc.nr_samples == 8) {
+ /* Calculate the Link Quality by the noise samples. */
+ average = 0;
+ for (i = 0; i < 8; i++) {
+ for (j = 0; j < 4; j++)
+ average += dev->noisecalc.samples[i][j];
+ }
+ average /= (8 * 4);
+ average *= 125;
+ average += 64;
+ average /= 128;
+ tmp = b43_shm_read16(dev, B43_SHM_SHARED, 0x40C);
+ tmp = (tmp / 128) & 0x1F;
+ if (tmp >= 8)
+ average += 2;
+ else
+ average -= 25;
+ if (tmp == 8)
+ average -= 72;
+ else
+ average -= 48;
+
+ dev->stats.link_noise = average;
+ drop_calculation:
+ dev->noisecalc.calculation_running = 0;
+ return;
+ }
+ generate_new:
+ b43_generate_noise_sample(dev);
+}
+
+static void handle_irq_tbtt_indication(struct b43_wldev *dev)
+{
+ if (b43_is_mode(dev->wl, IEEE80211_IF_TYPE_AP)) {
+ ///TODO: PS TBTT
+ } else {
+ if (1 /*FIXME: the last PSpoll frame was sent successfully */ )
+ b43_power_saving_ctl_bits(dev, 0);
+ }
+ dev->reg124_set_0x4 = 0;
+ if (b43_is_mode(dev->wl, IEEE80211_IF_TYPE_IBSS))
+ dev->reg124_set_0x4 = 1;
+}
+
+static void handle_irq_atim_end(struct b43_wldev *dev)
+{
+ if (!dev->reg124_set_0x4 /*FIXME rename this variable */ )
+ return;
+ b43_write32(dev, B43_MMIO_STATUS2_BITFIELD,
+ b43_read32(dev, B43_MMIO_STATUS2_BITFIELD)
+ | 0x4);
+}
+
+static void handle_irq_pmq(struct b43_wldev *dev)
+{
+ u32 tmp;
+
+ //TODO: AP mode.
+
+ while (1) {
+ tmp = b43_read32(dev, B43_MMIO_PS_STATUS);
+ if (!(tmp & 0x00000008))
+ break;
+ }
+ /* 16bit write is odd, but correct. */
+ b43_write16(dev, B43_MMIO_PS_STATUS, 0x0002);
+}
+
+static void b43_write_template_common(struct b43_wldev *dev,
+ const u8 * data, u16 size,
+ u16 ram_offset,
+ u16 shm_size_offset, u8 rate)
+{
+ u32 i, tmp;
+ struct b43_plcp_hdr4 plcp;
+
+ plcp.data = 0;
+ b43_generate_plcp_hdr(&plcp, size + FCS_LEN, rate);
+ b43_ram_write(dev, ram_offset, le32_to_cpu(plcp.data));
+ ram_offset += sizeof(u32);
+ /* The PLCP is 6 bytes long, but we only wrote 4 bytes, yet.
+ * So leave the first two bytes of the next write blank.
+ */
+ tmp = (u32) (data[0]) << 16;
+ tmp |= (u32) (data[1]) << 24;
+ b43_ram_write(dev, ram_offset, tmp);
+ ram_offset += sizeof(u32);
+ for (i = 2; i < size; i += sizeof(u32)) {
+ tmp = (u32) (data[i + 0]);
+ if (i + 1 < size)
+ tmp |= (u32) (data[i + 1]) << 8;
+ if (i + 2 < size)
+ tmp |= (u32) (data[i + 2]) << 16;
+ if (i + 3 < size)
+ tmp |= (u32) (data[i + 3]) << 24;
+ b43_ram_write(dev, ram_offset + i - 2, tmp);
+ }
+ b43_shm_write16(dev, B43_SHM_SHARED, shm_size_offset,
+ size + sizeof(struct b43_plcp_hdr6));
+}
+
+static void b43_write_beacon_template(struct b43_wldev *dev,
+ u16 ram_offset,
+ u16 shm_size_offset, u8 rate)
+{
+ int len;
+ const u8 *data;
+
+ B43_WARN_ON(!dev->cached_beacon);
+ len = min((size_t) dev->cached_beacon->len,
+ 0x200 - sizeof(struct b43_plcp_hdr6));
+ data = (const u8 *)(dev->cached_beacon->data);
+ b43_write_template_common(dev, data,
+ len, ram_offset, shm_size_offset, rate);
+}
+
+static void b43_write_probe_resp_plcp(struct b43_wldev *dev,
+ u16 shm_offset, u16 size, u8 rate)
+{
+ struct b43_plcp_hdr4 plcp;
+ u32 tmp;
+ __le16 dur;
+
+ plcp.data = 0;
+ b43_generate_plcp_hdr(&plcp, size + FCS_LEN, rate);
+ dur = ieee80211_generic_frame_duration(dev->wl->hw,
+ dev->wl->if_id, size,
+ B43_RATE_TO_BASE100KBPS(rate));
+ /* Write PLCP in two parts and timing for packet transfer */
+ tmp = le32_to_cpu(plcp.data);
+ b43_shm_write16(dev, B43_SHM_SHARED, shm_offset, tmp & 0xFFFF);
+ b43_shm_write16(dev, B43_SHM_SHARED, shm_offset + 2, tmp >> 16);
+ b43_shm_write16(dev, B43_SHM_SHARED, shm_offset + 6, le16_to_cpu(dur));
+}
+
+/* Instead of using custom probe response template, this function
+ * just patches custom beacon template by:
+ * 1) Changing packet type
+ * 2) Patching duration field
+ * 3) Stripping TIM
+ */
+static u8 *b43_generate_probe_resp(struct b43_wldev *dev,
+ u16 * dest_size, u8 rate)
+{
+ const u8 *src_data;
+ u8 *dest_data;
+ u16 src_size, elem_size, src_pos, dest_pos;
+ __le16 dur;
+ struct ieee80211_hdr *hdr;
+
+ B43_WARN_ON(!dev->cached_beacon);
+ src_size = dev->cached_beacon->len;
+ src_data = (const u8 *)dev->cached_beacon->data;
+
+ if (unlikely(src_size < 0x24)) {
+ b43dbg(dev->wl, "b43_generate_probe_resp: " "invalid beacon\n");
+ return NULL;
+ }
+
+ dest_data = kmalloc(src_size, GFP_ATOMIC);
+ if (unlikely(!dest_data))
+ return NULL;
+
+ /* 0x24 is offset of first variable-len Information-Element
+ * in beacon frame.
+ */
+ memcpy(dest_data, src_data, 0x24);
+ src_pos = dest_pos = 0x24;
+ for (; src_pos < src_size - 2; src_pos += elem_size) {
+ elem_size = src_data[src_pos + 1] + 2;
+ if (src_data[src_pos] != 0x05) { /* TIM */
+ memcpy(dest_data + dest_pos, src_data + src_pos,
+ elem_size);
+ dest_pos += elem_size;
+ }
+ }
+ *dest_size = dest_pos;
+ hdr = (struct ieee80211_hdr *)dest_data;
+
+ /* Set the frame control. */
+ hdr->frame_control = cpu_to_le16(IEEE80211_FTYPE_MGMT |
+ IEEE80211_STYPE_PROBE_RESP);
+ dur = ieee80211_generic_frame_duration(dev->wl->hw,
+ dev->wl->if_id, *dest_size,
+ B43_RATE_TO_BASE100KBPS(rate));
+ hdr->duration_id = dur;
+
+ return dest_data;
+}
+
+static void b43_write_probe_resp_template(struct b43_wldev *dev,
+ u16 ram_offset,
+ u16 shm_size_offset, u8 rate)
+{
+ u8 *probe_resp_data;
+ u16 size;
+
+ B43_WARN_ON(!dev->cached_beacon);
+ size = dev->cached_beacon->len;
+ probe_resp_data = b43_generate_probe_resp(dev, &size, rate);
+ if (unlikely(!probe_resp_data))
+ return;
+
+ /* Looks like PLCP headers plus packet timings are stored for
+ * all possible basic rates
+ */
+ b43_write_probe_resp_plcp(dev, 0x31A, size, B43_CCK_RATE_1MB);
+ b43_write_probe_resp_plcp(dev, 0x32C, size, B43_CCK_RATE_2MB);
+ b43_write_probe_resp_plcp(dev, 0x33E, size, B43_CCK_RATE_5MB);
+ b43_write_probe_resp_plcp(dev, 0x350, size, B43_CCK_RATE_11MB);
+
+ size = min((size_t) size, 0x200 - sizeof(struct b43_plcp_hdr6));
+ b43_write_template_common(dev, probe_resp_data,
+ size, ram_offset, shm_size_offset, rate);
+ kfree(probe_resp_data);
+}
+
+static int b43_refresh_cached_beacon(struct b43_wldev *dev,
+ struct sk_buff *beacon)
+{
+ if (dev->cached_beacon)
+ kfree_skb(dev->cached_beacon);
+ dev->cached_beacon = beacon;
+
+ return 0;
+}
+
+static void b43_update_templates(struct b43_wldev *dev)
+{
+ u32 status;
+
+ B43_WARN_ON(!dev->cached_beacon);
+
+ b43_write_beacon_template(dev, 0x68, 0x18, B43_CCK_RATE_1MB);
+ b43_write_beacon_template(dev, 0x468, 0x1A, B43_CCK_RATE_1MB);
+ b43_write_probe_resp_template(dev, 0x268, 0x4A, B43_CCK_RATE_11MB);
+
+ status = b43_read32(dev, B43_MMIO_STATUS2_BITFIELD);
+ status |= 0x03;
+ b43_write32(dev, B43_MMIO_STATUS2_BITFIELD, status);
+}
+
+static void b43_refresh_templates(struct b43_wldev *dev, struct sk_buff *beacon)
+{
+ int err;
+
+ err = b43_refresh_cached_beacon(dev, beacon);
+ if (unlikely(err))
+ return;
+ b43_update_templates(dev);
+}
+
+static void b43_set_ssid(struct b43_wldev *dev, const u8 * ssid, u8 ssid_len)
+{
+ u32 tmp;
+ u16 i, len;
+
+ len = min((u16) ssid_len, (u16) 0x100);
+ for (i = 0; i < len; i += sizeof(u32)) {
+ tmp = (u32) (ssid[i + 0]);
+ if (i + 1 < len)
+ tmp |= (u32) (ssid[i + 1]) << 8;
+ if (i + 2 < len)
+ tmp |= (u32) (ssid[i + 2]) << 16;
+ if (i + 3 < len)
+ tmp |= (u32) (ssid[i + 3]) << 24;
+ b43_shm_write32(dev, B43_SHM_SHARED, 0x380 + i, tmp);
+ }
+ b43_shm_write16(dev, B43_SHM_SHARED, 0x48, len);
+}
+
+static void b43_set_beacon_int(struct b43_wldev *dev, u16 beacon_int)
+{
+ b43_time_lock(dev);
+ if (dev->dev->id.revision >= 3) {
+ b43_write32(dev, 0x188, (beacon_int << 16));
+ } else {
+ b43_write16(dev, 0x606, (beacon_int >> 6));
+ b43_write16(dev, 0x610, beacon_int);
+ }
+ b43_time_unlock(dev);
+}
+
+static void handle_irq_beacon(struct b43_wldev *dev)
+{
+ u32 status;
+
+ if (!b43_is_mode(dev->wl, IEEE80211_IF_TYPE_AP))
+ return;
+
+ dev->irq_savedstate &= ~B43_IRQ_BEACON;
+ status = b43_read32(dev, B43_MMIO_STATUS2_BITFIELD);
+
+ if (!dev->cached_beacon || ((status & 0x1) && (status & 0x2))) {
+ /* ACK beacon IRQ. */
+ b43_write32(dev, B43_MMIO_GEN_IRQ_REASON, B43_IRQ_BEACON);
+ dev->irq_savedstate |= B43_IRQ_BEACON;
+ if (dev->cached_beacon)
+ kfree_skb(dev->cached_beacon);
+ dev->cached_beacon = NULL;
+ return;
+ }
+ if (!(status & 0x1)) {
+ b43_write_beacon_template(dev, 0x68, 0x18, B43_CCK_RATE_1MB);
+ status |= 0x1;
+ b43_write32(dev, B43_MMIO_STATUS2_BITFIELD, status);
+ }
+ if (!(status & 0x2)) {
+ b43_write_beacon_template(dev, 0x468, 0x1A, B43_CCK_RATE_1MB);
+ status |= 0x2;
+ b43_write32(dev, B43_MMIO_STATUS2_BITFIELD, status);
+ }
+}
+
+static void handle_irq_ucode_debug(struct b43_wldev *dev)
+{
+ //TODO
+}
+
+/* Interrupt handler bottom-half */
+static void b43_interrupt_tasklet(struct b43_wldev *dev)
+{
+ u32 reason;
+ u32 dma_reason[ARRAY_SIZE(dev->dma_reason)];
+ u32 merged_dma_reason = 0;
+ int i, activity = 0;
+ unsigned long flags;
+
+ spin_lock_irqsave(&dev->wl->irq_lock, flags);
+
+ B43_WARN_ON(b43_status(dev) != B43_STAT_STARTED);
+
+ reason = dev->irq_reason;
+ for (i = 0; i < ARRAY_SIZE(dma_reason); i++) {
+ dma_reason[i] = dev->dma_reason[i];
+ merged_dma_reason |= dma_reason[i];
+ }
+
+ if (unlikely(reason & B43_IRQ_MAC_TXERR))
+ b43err(dev->wl, "MAC transmission error\n");
+
+ if (unlikely(reason & B43_IRQ_PHY_TXERR))
+ b43err(dev->wl, "PHY transmission error\n");
+
+ if (unlikely(merged_dma_reason & (B43_DMAIRQ_FATALMASK |
+ B43_DMAIRQ_NONFATALMASK))) {
+ if (merged_dma_reason & B43_DMAIRQ_FATALMASK) {
+ b43err(dev->wl, "Fatal DMA error: "
+ "0x%08X, 0x%08X, 0x%08X, "
+ "0x%08X, 0x%08X, 0x%08X\n",
+ dma_reason[0], dma_reason[1],
+ dma_reason[2], dma_reason[3],
+ dma_reason[4], dma_reason[5]);
+ b43_controller_restart(dev, "DMA error");
+ mmiowb();
+ spin_unlock_irqrestore(&dev->wl->irq_lock, flags);
+ return;
+ }
+ if (merged_dma_reason & B43_DMAIRQ_NONFATALMASK) {
+ b43err(dev->wl, "DMA error: "
+ "0x%08X, 0x%08X, 0x%08X, "
+ "0x%08X, 0x%08X, 0x%08X\n",
+ dma_reason[0], dma_reason[1],
+ dma_reason[2], dma_reason[3],
+ dma_reason[4], dma_reason[5]);
+ }
+ }
+
+ if (unlikely(reason & B43_IRQ_UCODE_DEBUG))
+ handle_irq_ucode_debug(dev);
+ if (reason & B43_IRQ_TBTT_INDI)
+ handle_irq_tbtt_indication(dev);
+ if (reason & B43_IRQ_ATIM_END)
+ handle_irq_atim_end(dev);
+ if (reason & B43_IRQ_BEACON)
+ handle_irq_beacon(dev);
+ if (reason & B43_IRQ_PMQ)
+ handle_irq_pmq(dev);
+ if (reason & B43_IRQ_TXFIFO_FLUSH_OK) ;
+ /*TODO*/ if (reason & B43_IRQ_NOISESAMPLE_OK)
+ handle_irq_noise(dev);
+
+ /* Check the DMA reason registers for received data. */
+ if (dma_reason[0] & B43_DMAIRQ_RX_DONE) {
+ if (b43_using_pio(dev))
+ b43_pio_rx(dev->pio.queue0);
+ else
+ b43_dma_rx(dev->dma.rx_ring0);
+ /* We intentionally don't set "activity" to 1, here. */
+ }
+ B43_WARN_ON(dma_reason[1] & B43_DMAIRQ_RX_DONE);
+ B43_WARN_ON(dma_reason[2] & B43_DMAIRQ_RX_DONE);
+ if (dma_reason[3] & B43_DMAIRQ_RX_DONE) {
+ if (b43_using_pio(dev))
+ b43_pio_rx(dev->pio.queue3);
+ else
+ b43_dma_rx(dev->dma.rx_ring3);
+ activity = 1;
+ }
+ B43_WARN_ON(dma_reason[4] & B43_DMAIRQ_RX_DONE);
+ B43_WARN_ON(dma_reason[5] & B43_DMAIRQ_RX_DONE);
+
+ if (reason & B43_IRQ_TX_OK) {
+ handle_irq_transmit_status(dev);
+ activity = 1;
+ //TODO: In AP mode, this also causes sending of powersave responses.
+ }
+
+ if (!modparam_noleds)
+ b43_leds_update(dev, activity);
+ b43_interrupt_enable(dev, dev->irq_savedstate);
+ mmiowb();
+ spin_unlock_irqrestore(&dev->wl->irq_lock, flags);
+}
+
+static void pio_irq_workaround(struct b43_wldev *dev, u16 base, int queueidx)
+{
+ u16 rxctl;
+
+ rxctl = b43_read16(dev, base + B43_PIO_RXCTL);
+ if (rxctl & B43_PIO_RXCTL_DATAAVAILABLE)
+ dev->dma_reason[queueidx] |= B43_DMAIRQ_RX_DONE;
+ else
+ dev->dma_reason[queueidx] &= ~B43_DMAIRQ_RX_DONE;
+}
+
+static void b43_interrupt_ack(struct b43_wldev *dev, u32 reason)
+{
+ if (b43_using_pio(dev) &&
+ (dev->dev->id.revision < 3) &&
+ (!(reason & B43_IRQ_PIO_WORKAROUND))) {
+ /* Apply a PIO specific workaround to the dma_reasons */
+ pio_irq_workaround(dev, B43_MMIO_PIO1_BASE, 0);
+ pio_irq_workaround(dev, B43_MMIO_PIO2_BASE, 1);
+ pio_irq_workaround(dev, B43_MMIO_PIO3_BASE, 2);
+ pio_irq_workaround(dev, B43_MMIO_PIO4_BASE, 3);
+ }
+
+ b43_write32(dev, B43_MMIO_GEN_IRQ_REASON, reason);
+
+ b43_write32(dev, B43_MMIO_DMA0_REASON, dev->dma_reason[0]);
+ b43_write32(dev, B43_MMIO_DMA1_REASON, dev->dma_reason[1]);
+ b43_write32(dev, B43_MMIO_DMA2_REASON, dev->dma_reason[2]);
+ b43_write32(dev, B43_MMIO_DMA3_REASON, dev->dma_reason[3]);
+ b43_write32(dev, B43_MMIO_DMA4_REASON, dev->dma_reason[4]);
+ b43_write32(dev, B43_MMIO_DMA5_REASON, dev->dma_reason[5]);
+}
+
+/* Interrupt handler top-half */
+static irqreturn_t b43_interrupt_handler(int irq, void *dev_id)
+{
+ irqreturn_t ret = IRQ_NONE;
+ struct b43_wldev *dev = dev_id;
+ u32 reason;
+
+ if (!dev)
+ return IRQ_NONE;
+
+ spin_lock(&dev->wl->irq_lock);
+
+ if (b43_status(dev) < B43_STAT_STARTED)
+ goto out;
+ reason = b43_read32(dev, B43_MMIO_GEN_IRQ_REASON);
+ if (reason == 0xffffffff) /* shared IRQ */
+ goto out;
+ ret = IRQ_HANDLED;
+ reason &= b43_read32(dev, B43_MMIO_GEN_IRQ_MASK);
+ if (!reason)
+ goto out;
+
+ dev->dma_reason[0] = b43_read32(dev, B43_MMIO_DMA0_REASON)
+ & 0x0001DC00;
+ dev->dma_reason[1] = b43_read32(dev, B43_MMIO_DMA1_REASON)
+ & 0x0000DC00;
+ dev->dma_reason[2] = b43_read32(dev, B43_MMIO_DMA2_REASON)
+ & 0x0000DC00;
+ dev->dma_reason[3] = b43_read32(dev, B43_MMIO_DMA3_REASON)
+ & 0x0001DC00;
+ dev->dma_reason[4] = b43_read32(dev, B43_MMIO_DMA4_REASON)
+ & 0x0000DC00;
+ dev->dma_reason[5] = b43_read32(dev, B43_MMIO_DMA5_REASON)
+ & 0x0000DC00;
+
+ b43_interrupt_ack(dev, reason);
+ /* disable all IRQs. They are enabled again in the bottom half. */
+ dev->irq_savedstate = b43_interrupt_disable(dev, B43_IRQ_ALL);
+ /* save the reason code and call our bottom half. */
+ dev->irq_reason = reason;
+ tasklet_schedule(&dev->isr_tasklet);
+ out:
+ mmiowb();
+ spin_unlock(&dev->wl->irq_lock);
+
+ return ret;
+}
+
+static void b43_release_firmware(struct b43_wldev *dev)
+{
+ release_firmware(dev->fw.ucode);
+ dev->fw.ucode = NULL;
+ release_firmware(dev->fw.pcm);
+ dev->fw.pcm = NULL;
+ release_firmware(dev->fw.initvals);
+ dev->fw.initvals = NULL;
+ release_firmware(dev->fw.initvals_band);
+ dev->fw.initvals_band = NULL;
+}
+
+static void b43_print_fw_helptext(struct b43_wl *wl)
+{
+ b43err(wl, "You must go to "
+ "http://linuxwireless.org/en/users/Drivers/bcm43xx#devicefirmware "
+ "and download the correct firmware (version 4).\n");
+}
+
+static int do_request_fw(struct b43_wldev *dev,
+ const char *name,
+ const struct firmware **fw)
+{
+ const size_t plen = sizeof(modparam_fwpostfix) + 32;
+ char path[plen];
+ struct b43_fw_header *hdr;
+ u32 size;
+ int err;
+
+ if (!name)
+ return 0;
+
+ snprintf(path, ARRAY_SIZE(path),
+ "b43%s/%s.fw",
+ modparam_fwpostfix, name);
+ err = request_firmware(fw, path, dev->dev->dev);
+ if (err) {
+ b43err(dev->wl, "Firmware file \"%s\" not found "
+ "or load failed.\n", path);
+ return err;
+ }
+ if ((*fw)->size < sizeof(struct b43_fw_header))
+ goto err_format;
+ hdr = (struct b43_fw_header *)((*fw)->data);
+ switch (hdr->type) {
+ case B43_FW_TYPE_UCODE:
+ case B43_FW_TYPE_PCM:
+ size = be32_to_cpu(hdr->size);
+ if (size != (*fw)->size - sizeof(struct b43_fw_header))
+ goto err_format;
+ /* fallthrough */
+ case B43_FW_TYPE_IV:
+ if (hdr->ver != 1)
+ goto err_format;
+ break;
+ default:
+ goto err_format;
+ }
+
+ return err;
+
+err_format:
+ b43err(dev->wl, "Firmware file \"%s\" format error.\n", path);
+ return -EPROTO;
+}
+
+static int b43_request_firmware(struct b43_wldev *dev)
+{
+ struct b43_firmware *fw = &dev->fw;
+ const u8 rev = dev->dev->id.revision;
+ const char *filename;
+ u32 tmshigh;
+ int err;
+
+ tmshigh = ssb_read32(dev->dev, SSB_TMSHIGH);
+ if (!fw->ucode) {
+ if ((rev >= 5) && (rev <= 10))
+ filename = "ucode5";
+ else if ((rev >= 11) && (rev <= 12))
+ filename = "ucode11";
+ else if (rev >= 13)
+ filename = "ucode13";
+ else
+ goto err_no_ucode;
+ err = do_request_fw(dev, filename, &fw->ucode);
+ if (err)
+ goto err_load;
+ }
+ if (!fw->pcm) {
+ if ((rev >= 5) && (rev <= 10))
+ filename = "pcm5";
+ else if (rev >= 11)
+ filename = NULL;
+ else
+ goto err_no_pcm;
+ err = do_request_fw(dev, filename, &fw->pcm);
+ if (err)
+ goto err_load;
+ }
+ if (!fw->initvals) {
+ switch (dev->phy.type) {
+ case B43_PHYTYPE_A:
+ if ((rev >= 5) && (rev <= 10)) {
+ if (tmshigh & B43_TMSHIGH_GPHY)
+ filename = "a0g1initvals5";
+ else
+ filename = "a0g0initvals5";
+ } else
+ goto err_no_initvals;
+ break;
+ case B43_PHYTYPE_G:
+ if ((rev >= 5) && (rev <= 10))
+ filename = "b0g0initvals5";
+ else if (rev >= 13)
+ filename = "lp0initvals13";
+ else
+ goto err_no_initvals;
+ break;
+ default:
+ goto err_no_initvals;
+ }
+ err = do_request_fw(dev, filename, &fw->initvals);
+ if (err)
+ goto err_load;
+ }
+ if (!fw->initvals_band) {
+ switch (dev->phy.type) {
+ case B43_PHYTYPE_A:
+ if ((rev >= 5) && (rev <= 10)) {
+ if (tmshigh & B43_TMSHIGH_GPHY)
+ filename = "a0g1bsinitvals5";
+ else
+ filename = "a0g0bsinitvals5";
+ } else if (rev >= 11)
+ filename = NULL;
+ else
+ goto err_no_initvals;
+ break;
+ case B43_PHYTYPE_G:
+ if ((rev >= 5) && (rev <= 10))
+ filename = "b0g0bsinitvals5";
+ else if (rev >= 11)
+ filename = NULL;
+ else
+ goto err_no_initvals;
+ break;
+ default:
+ goto err_no_initvals;
+ }
+ err = do_request_fw(dev, filename, &fw->initvals_band);
+ if (err)
+ goto err_load;
+ }
+
+ return 0;
+
+err_load:
+ b43_print_fw_helptext(dev->wl);
+ goto error;
+
+err_no_ucode:
+ err = -ENODEV;
+ b43err(dev->wl, "No microcode available for core rev %u\n", rev);
+ goto error;
+
+err_no_pcm:
+ err = -ENODEV;
+ b43err(dev->wl, "No PCM available for core rev %u\n", rev);
+ goto error;
+
+err_no_initvals:
+ err = -ENODEV;
+ b43err(dev->wl, "No Initial Values firmware file for PHY %u, "
+ "core rev %u\n", dev->phy.type, rev);
+ goto error;
+
+error:
+ b43_release_firmware(dev);
+ return err;
+}
+
+static int b43_upload_microcode(struct b43_wldev *dev)
+{
+ const size_t hdr_len = sizeof(struct b43_fw_header);
+ const __be32 *data;
+ unsigned int i, len;
+ u16 fwrev, fwpatch, fwdate, fwtime;
+ u32 tmp;
+ int err = 0;
+
+ /* Upload Microcode. */
+ data = (__be32 *) (dev->fw.ucode->data + hdr_len);
+ len = (dev->fw.ucode->size - hdr_len) / sizeof(__be32);
+ b43_shm_control_word(dev, B43_SHM_UCODE | B43_SHM_AUTOINC_W, 0x0000);
+ for (i = 0; i < len; i++) {
+ b43_write32(dev, B43_MMIO_SHM_DATA, be32_to_cpu(data[i]));
+ udelay(10);
+ }
+
+ if (dev->fw.pcm) {
+ /* Upload PCM data. */
+ data = (__be32 *) (dev->fw.pcm->data + hdr_len);
+ len = (dev->fw.pcm->size - hdr_len) / sizeof(__be32);
+ b43_shm_control_word(dev, B43_SHM_HW, 0x01EA);
+ b43_write32(dev, B43_MMIO_SHM_DATA, 0x00004000);
+ /* No need for autoinc bit in SHM_HW */
+ b43_shm_control_word(dev, B43_SHM_HW, 0x01EB);
+ for (i = 0; i < len; i++) {
+ b43_write32(dev, B43_MMIO_SHM_DATA, be32_to_cpu(data[i]));
+ udelay(10);
+ }
+ }
+
+ b43_write32(dev, B43_MMIO_GEN_IRQ_REASON, B43_IRQ_ALL);
+ b43_write32(dev, B43_MMIO_MACCTL,
+ B43_MACCTL_PSM_RUN |
+ B43_MACCTL_IHR_ENABLED | B43_MACCTL_INFRA);
+
+ /* Wait for the microcode to load and respond */
+ i = 0;
+ while (1) {
+ tmp = b43_read32(dev, B43_MMIO_GEN_IRQ_REASON);
+ if (tmp == B43_IRQ_MAC_SUSPENDED)
+ break;
+ i++;
+ if (i >= 50) {
+ b43err(dev->wl, "Microcode not responding\n");
+ b43_print_fw_helptext(dev->wl);
+ err = -ENODEV;
+ goto out;
+ }
+ udelay(10);
+ }
+ b43_read32(dev, B43_MMIO_GEN_IRQ_REASON); /* dummy read */
+
+ /* Get and check the revisions. */
+ fwrev = b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_UCODEREV);
+ fwpatch = b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_UCODEPATCH);
+ fwdate = b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_UCODEDATE);
+ fwtime = b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_UCODETIME);
+
+ if (fwrev <= 0x128) {
+ b43err(dev->wl, "YOUR FIRMWARE IS TOO OLD. Firmware from "
+ "binary drivers older than version 4.x is unsupported. "
+ "You must upgrade your firmware files.\n");
+ b43_print_fw_helptext(dev->wl);
+ b43_write32(dev, B43_MMIO_MACCTL, 0);
+ err = -EOPNOTSUPP;
+ goto out;
+ }
+ b43dbg(dev->wl, "Loading firmware version %u.%u "
+ "(20%.2i-%.2i-%.2i %.2i:%.2i:%.2i)\n",
+ fwrev, fwpatch,
+ (fwdate >> 12) & 0xF, (fwdate >> 8) & 0xF, fwdate & 0xFF,
+ (fwtime >> 11) & 0x1F, (fwtime >> 5) & 0x3F, fwtime & 0x1F);
+
+ dev->fw.rev = fwrev;
+ dev->fw.patch = fwpatch;
+
+ out:
+ return err;
+}
+
+static int b43_write_initvals(struct b43_wldev *dev,
+ const struct b43_iv *ivals,
+ size_t count,
+ size_t array_size)
+{
+ const struct b43_iv *iv;
+ u16 offset;
+ size_t i;
+ bool bit32;
+
+ BUILD_BUG_ON(sizeof(struct b43_iv) != 6);
+ iv = ivals;
+ for (i = 0; i < count; i++) {
+ if (array_size < sizeof(iv->offset_size))
+ goto err_format;
+ array_size -= sizeof(iv->offset_size);
+ offset = be16_to_cpu(iv->offset_size);
+ bit32 = !!(offset & B43_IV_32BIT);
+ offset &= B43_IV_OFFSET_MASK;
+ if (offset >= 0x1000)
+ goto err_format;
+ if (bit32) {
+ u32 value;
+
+ if (array_size < sizeof(iv->data.d32))
+ goto err_format;
+ array_size -= sizeof(iv->data.d32);
+
+ value = be32_to_cpu(get_unaligned(&iv->data.d32));
+ b43_write32(dev, offset, value);
+
+ iv = (const struct b43_iv *)((const uint8_t *)iv +
+ sizeof(__be16) +
+ sizeof(__be32));
+ } else {
+ u16 value;
+
+ if (array_size < sizeof(iv->data.d16))
+ goto err_format;
+ array_size -= sizeof(iv->data.d16);
+
+ value = be16_to_cpu(iv->data.d16);
+ b43_write16(dev, offset, value);
+
+ iv = (const struct b43_iv *)((const uint8_t *)iv +
+ sizeof(__be16) +
+ sizeof(__be16));
+ }
+ }
+ if (array_size)
+ goto err_format;
+
+ return 0;
+
+err_format:
+ b43err(dev->wl, "Initial Values Firmware file-format error.\n");
+ b43_print_fw_helptext(dev->wl);
+
+ return -EPROTO;
+}
+
+static int b43_upload_initvals(struct b43_wldev *dev)
+{
+ const size_t hdr_len = sizeof(struct b43_fw_header);
+ const struct b43_fw_header *hdr;
+ struct b43_firmware *fw = &dev->fw;
+ const struct b43_iv *ivals;
+ size_t count;
+ int err;
+
+ hdr = (const struct b43_fw_header *)(fw->initvals->data);
+ ivals = (const struct b43_iv *)(fw->initvals->data + hdr_len);
+ count = be32_to_cpu(hdr->size);
+ err = b43_write_initvals(dev, ivals, count,
+ fw->initvals->size - hdr_len);
+ if (err)
+ goto out;
+ if (fw->initvals_band) {
+ hdr = (const struct b43_fw_header *)(fw->initvals_band->data);
+ ivals = (const struct b43_iv *)(fw->initvals_band->data + hdr_len);
+ count = be32_to_cpu(hdr->size);
+ err = b43_write_initvals(dev, ivals, count,
+ fw->initvals_band->size - hdr_len);
+ if (err)
+ goto out;
+ }
+out:
+
+ return err;
+}
+
+/* Initialize the GPIOs
+ * http://bcm-specs.sipsolutions.net/GPIO
+ */
+static int b43_gpio_init(struct b43_wldev *dev)
+{
+ struct ssb_bus *bus = dev->dev->bus;
+ struct ssb_device *gpiodev, *pcidev = NULL;
+ u32 mask, set;
+
+ b43_write32(dev, B43_MMIO_MACCTL, b43_read32(dev, B43_MMIO_MACCTL)
+ & ~B43_MACCTL_GPOUTSMSK);
+
+ b43_leds_switch_all(dev, 0);
+ b43_write16(dev, B43_MMIO_GPIO_MASK, b43_read16(dev, B43_MMIO_GPIO_MASK)
+ | 0x000F);
+
+ mask = 0x0000001F;
+ set = 0x0000000F;
+ if (dev->dev->bus->chip_id == 0x4301) {
+ mask |= 0x0060;
+ set |= 0x0060;
+ }
+ if (0 /* FIXME: conditional unknown */ ) {
+ b43_write16(dev, B43_MMIO_GPIO_MASK,
+ b43_read16(dev, B43_MMIO_GPIO_MASK)
+ | 0x0100);
+ mask |= 0x0180;
+ set |= 0x0180;
+ }
+ if (dev->dev->bus->sprom.r1.boardflags_lo & B43_BFL_PACTRL) {
+ b43_write16(dev, B43_MMIO_GPIO_MASK,
+ b43_read16(dev, B43_MMIO_GPIO_MASK)
+ | 0x0200);
+ mask |= 0x0200;
+ set |= 0x0200;
+ }
+ if (dev->dev->id.revision >= 2)
+ mask |= 0x0010; /* FIXME: This is redundant. */
+
+#ifdef CONFIG_SSB_DRIVER_PCICORE
+ pcidev = bus->pcicore.dev;
+#endif
+ gpiodev = bus->chipco.dev ? : pcidev;
+ if (!gpiodev)
+ return 0;
+ ssb_write32(gpiodev, B43_GPIO_CONTROL,
+ (ssb_read32(gpiodev, B43_GPIO_CONTROL)
+ & mask) | set);
+
+ return 0;
+}
+
+/* Turn off all GPIO stuff. Call this on module unload, for example. */
+static void b43_gpio_cleanup(struct b43_wldev *dev)
+{
+ struct ssb_bus *bus = dev->dev->bus;
+ struct ssb_device *gpiodev, *pcidev = NULL;
+
+#ifdef CONFIG_SSB_DRIVER_PCICORE
+ pcidev = bus->pcicore.dev;
+#endif
+ gpiodev = bus->chipco.dev ? : pcidev;
+ if (!gpiodev)
+ return;
+ ssb_write32(gpiodev, B43_GPIO_CONTROL, 0);
+}
+
+/* http://bcm-specs.sipsolutions.net/EnableMac */
+void b43_mac_enable(struct b43_wldev *dev)
+{
+ dev->mac_suspended--;
+ B43_WARN_ON(dev->mac_suspended < 0);
+ if (dev->mac_suspended == 0) {
+ b43_write32(dev, B43_MMIO_MACCTL,
+ b43_read32(dev, B43_MMIO_MACCTL)
+ | B43_MACCTL_ENABLED);
+ b43_write32(dev, B43_MMIO_GEN_IRQ_REASON,
+ B43_IRQ_MAC_SUSPENDED);
+ /* Commit writes */
+ b43_read32(dev, B43_MMIO_MACCTL);
+ b43_read32(dev, B43_MMIO_GEN_IRQ_REASON);
+ b43_power_saving_ctl_bits(dev, 0);
+ }
+}
+
+/* http://bcm-specs.sipsolutions.net/SuspendMAC */
+void b43_mac_suspend(struct b43_wldev *dev)
+{
+ int i;
+ u32 tmp;
+
+ B43_WARN_ON(dev->mac_suspended < 0);
+ if (dev->mac_suspended == 0) {
+ b43_power_saving_ctl_bits(dev, B43_PS_AWAKE);
+ b43_write32(dev, B43_MMIO_MACCTL,
+ b43_read32(dev, B43_MMIO_MACCTL)
+ & ~B43_MACCTL_ENABLED);
+ /* force pci to flush the write */
+ b43_read32(dev, B43_MMIO_MACCTL);
+ for (i = 10000; i; i--) {
+ tmp = b43_read32(dev, B43_MMIO_GEN_IRQ_REASON);
+ if (tmp & B43_IRQ_MAC_SUSPENDED)
+ goto out;
+ udelay(1);
+ }
+ b43err(dev->wl, "MAC suspend failed\n");
+ }
+ out:
+ dev->mac_suspended++;
+}
+
+static void b43_adjust_opmode(struct b43_wldev *dev)
+{
+ struct b43_wl *wl = dev->wl;
+ u32 ctl;
+ u16 cfp_pretbtt;
+
+ ctl = b43_read32(dev, B43_MMIO_MACCTL);
+ /* Reset status to STA infrastructure mode. */
+ ctl &= ~B43_MACCTL_AP;
+ ctl &= ~B43_MACCTL_KEEP_CTL;
+ ctl &= ~B43_MACCTL_KEEP_BADPLCP;
+ ctl &= ~B43_MACCTL_KEEP_BAD;
+ ctl &= ~B43_MACCTL_PROMISC;
+ ctl |= B43_MACCTL_INFRA;
+
+ if (wl->operating) {
+ switch (wl->if_type) {
+ case IEEE80211_IF_TYPE_AP:
+ ctl |= B43_MACCTL_AP;
+ break;
+ case IEEE80211_IF_TYPE_IBSS:
+ ctl &= ~B43_MACCTL_INFRA;
+ break;
+ case IEEE80211_IF_TYPE_STA:
+ case IEEE80211_IF_TYPE_MNTR:
+ case IEEE80211_IF_TYPE_WDS:
+ break;
+ default:
+ B43_WARN_ON(1);
+ }
+ }
+ if (wl->monitor) {
+ ctl |= B43_MACCTL_KEEP_CTL;
+ if (modparam_mon_keep_bad)
+ ctl |= B43_MACCTL_KEEP_BAD;
+ if (modparam_mon_keep_badplcp)
+ ctl |= B43_MACCTL_KEEP_BADPLCP;
+ }
+ if (wl->promisc)
+ ctl |= B43_MACCTL_PROMISC;
+ /* Workaround: On old hardware the HW-MAC-address-filter
+ * doesn't work properly, so always run promisc in filter
+ * it in software. */
+ if (dev->dev->id.revision <= 4)
+ ctl |= B43_MACCTL_PROMISC;
+
+ b43_write32(dev, B43_MMIO_MACCTL, ctl);
+
+ cfp_pretbtt = 2;
+ if ((ctl & B43_MACCTL_INFRA) && !(ctl & B43_MACCTL_AP)) {
+ if (dev->dev->bus->chip_id == 0x4306 &&
+ dev->dev->bus->chip_rev == 3)
+ cfp_pretbtt = 100;
+ else
+ cfp_pretbtt = 50;
+ }
+ b43_write16(dev, 0x612, cfp_pretbtt);
+}
+
+static void b43_rate_memory_write(struct b43_wldev *dev, u16 rate, int is_ofdm)
+{
+ u16 offset;
+
+ if (is_ofdm) {
+ offset = 0x480;
+ offset += (b43_plcp_get_ratecode_ofdm(rate) & 0x000F) * 2;
+ } else {
+ offset = 0x4C0;
+ offset += (b43_plcp_get_ratecode_cck(rate) & 0x000F) * 2;
+ }
+ b43_shm_write16(dev, B43_SHM_SHARED, offset + 0x20,
+ b43_shm_read16(dev, B43_SHM_SHARED, offset));
+}
+
+static void b43_rate_memory_init(struct b43_wldev *dev)
+{
+ switch (dev->phy.type) {
+ case B43_PHYTYPE_A:
+ case B43_PHYTYPE_G:
+ b43_rate_memory_write(dev, B43_OFDM_RATE_6MB, 1);
+ b43_rate_memory_write(dev, B43_OFDM_RATE_12MB, 1);
+ b43_rate_memory_write(dev, B43_OFDM_RATE_18MB, 1);
+ b43_rate_memory_write(dev, B43_OFDM_RATE_24MB, 1);
+ b43_rate_memory_write(dev, B43_OFDM_RATE_36MB, 1);
+ b43_rate_memory_write(dev, B43_OFDM_RATE_48MB, 1);
+ b43_rate_memory_write(dev, B43_OFDM_RATE_54MB, 1);
+ if (dev->phy.type == B43_PHYTYPE_A)
+ break;
+ /* fallthrough */
+ case B43_PHYTYPE_B:
+ b43_rate_memory_write(dev, B43_CCK_RATE_1MB, 0);
+ b43_rate_memory_write(dev, B43_CCK_RATE_2MB, 0);
+ b43_rate_memory_write(dev, B43_CCK_RATE_5MB, 0);
+ b43_rate_memory_write(dev, B43_CCK_RATE_11MB, 0);
+ break;
+ default:
+ B43_WARN_ON(1);
+ }
+}
+
+/* Set the TX-Antenna for management frames sent by firmware. */
+static void b43_mgmtframe_txantenna(struct b43_wldev *dev, int antenna)
+{
+ u16 ant = 0;
+ u16 tmp;
+
+ switch (antenna) {
+ case B43_ANTENNA0:
+ ant |= B43_TX4_PHY_ANT0;
+ break;
+ case B43_ANTENNA1:
+ ant |= B43_TX4_PHY_ANT1;
+ break;
+ case B43_ANTENNA_AUTO:
+ ant |= B43_TX4_PHY_ANTLAST;
+ break;
+ default:
+ B43_WARN_ON(1);
+ }
+
+ /* FIXME We also need to set the other flags of the PHY control field somewhere. */
+
+ /* For Beacons */
+ tmp = b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_BEACPHYCTL);
+ tmp = (tmp & ~B43_TX4_PHY_ANT) | ant;
+ b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_BEACPHYCTL, tmp);
+ /* For ACK/CTS */
+ tmp = b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_ACKCTSPHYCTL);
+ tmp = (tmp & ~B43_TX4_PHY_ANT) | ant;
+ b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_ACKCTSPHYCTL, tmp);
+ /* For Probe Resposes */
+ tmp = b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_PRPHYCTL);
+ tmp = (tmp & ~B43_TX4_PHY_ANT) | ant;
+ b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_PRPHYCTL, tmp);
+}
+
+/* This is the opposite of b43_chip_init() */
+static void b43_chip_exit(struct b43_wldev *dev)
+{
+ b43_radio_turn_off(dev);
+ if (!modparam_noleds)
+ b43_leds_exit(dev);
+ b43_gpio_cleanup(dev);
+ /* firmware is released later */
+}
+
+/* Initialize the chip
+ * http://bcm-specs.sipsolutions.net/ChipInit
+ */
+static int b43_chip_init(struct b43_wldev *dev)
+{
+ struct b43_phy *phy = &dev->phy;
+ int err, tmp;
+ u32 value32;
+ u16 value16;
+
+ b43_write32(dev, B43_MMIO_MACCTL,
+ B43_MACCTL_PSM_JMP0 | B43_MACCTL_IHR_ENABLED);
+
+ err = b43_request_firmware(dev);
+ if (err)
+ goto out;
+ err = b43_upload_microcode(dev);
+ if (err)
+ goto out; /* firmware is released later */
+
+ err = b43_gpio_init(dev);
+ if (err)
+ goto out; /* firmware is released later */
+ err = b43_upload_initvals(dev);
+ if (err)
+ goto err_gpio_cleanup;
+ b43_radio_turn_on(dev);
+ dev->radio_hw_enable = b43_is_hw_radio_enabled(dev);
+ b43dbg(dev->wl, "Radio %s by hardware\n",
+ (dev->radio_hw_enable == 0) ? "disabled" : "enabled");
+
+ b43_write16(dev, 0x03E6, 0x0000);
+ err = b43_phy_init(dev);
+ if (err)
+ goto err_radio_off;
+
+ /* Select initial Interference Mitigation. */
+ tmp = phy->interfmode;
+ phy->interfmode = B43_INTERFMODE_NONE;
+ b43_radio_set_interference_mitigation(dev, tmp);
+
+ b43_set_rx_antenna(dev, B43_ANTENNA_DEFAULT);
+ b43_mgmtframe_txantenna(dev, B43_ANTENNA_DEFAULT);
+
+ if (phy->type == B43_PHYTYPE_B) {
+ value16 = b43_read16(dev, 0x005E);
+ value16 |= 0x0004;
+ b43_write16(dev, 0x005E, value16);
+ }
+ b43_write32(dev, 0x0100, 0x01000000);
+ if (dev->dev->id.revision < 5)
+ b43_write32(dev, 0x010C, 0x01000000);
+
+ b43_write32(dev, B43_MMIO_MACCTL, b43_read32(dev, B43_MMIO_MACCTL)
+ & ~B43_MACCTL_INFRA);
+ b43_write32(dev, B43_MMIO_MACCTL, b43_read32(dev, B43_MMIO_MACCTL)
+ | B43_MACCTL_INFRA);
+ /* Let beacons come through */
+ b43_write32(dev, B43_MMIO_MACCTL, b43_read32(dev, B43_MMIO_MACCTL)
+ | B43_MACCTL_BEACPROMISC);
+
+ if (b43_using_pio(dev)) {
+ b43_write32(dev, 0x0210, 0x00000100);
+ b43_write32(dev, 0x0230, 0x00000100);
+ b43_write32(dev, 0x0250, 0x00000100);
+ b43_write32(dev, 0x0270, 0x00000100);
+ b43_shm_write16(dev, B43_SHM_SHARED, 0x0034, 0x0000);
+ }
+
+ /* Probe Response Timeout value */
+ /* FIXME: Default to 0, has to be set by ioctl probably... :-/ */
+ b43_shm_write16(dev, B43_SHM_SHARED, 0x0074, 0x0000);
+
+ /* Initially set the wireless operation mode. */
+ b43_adjust_opmode(dev);
+
+ if (dev->dev->id.revision < 3) {
+ b43_write16(dev, 0x060E, 0x0000);
+ b43_write16(dev, 0x0610, 0x8000);
+ b43_write16(dev, 0x0604, 0x0000);
+ b43_write16(dev, 0x0606, 0x0200);
+ } else {
+ b43_write32(dev, 0x0188, 0x80000000);
+ b43_write32(dev, 0x018C, 0x02000000);
+ }
+ b43_write32(dev, B43_MMIO_GEN_IRQ_REASON, 0x00004000);
+ b43_write32(dev, B43_MMIO_DMA0_IRQ_MASK, 0x0001DC00);
+ b43_write32(dev, B43_MMIO_DMA1_IRQ_MASK, 0x0000DC00);
+ b43_write32(dev, B43_MMIO_DMA2_IRQ_MASK, 0x0000DC00);
+ b43_write32(dev, B43_MMIO_DMA3_IRQ_MASK, 0x0001DC00);
+ b43_write32(dev, B43_MMIO_DMA4_IRQ_MASK, 0x0000DC00);
+ b43_write32(dev, B43_MMIO_DMA5_IRQ_MASK, 0x0000DC00);
+
+ value32 = ssb_read32(dev->dev, SSB_TMSLOW);
+ value32 |= 0x00100000;
+ ssb_write32(dev->dev, SSB_TMSLOW, value32);
+
+ b43_write16(dev, B43_MMIO_POWERUP_DELAY,
+ dev->dev->bus->chipco.fast_pwrup_delay);
+
+ err = 0;
+ b43dbg(dev->wl, "Chip initialized\n");
+ out:
+ return err;
+
+ err_radio_off:
+ b43_radio_turn_off(dev);
+ err_gpio_cleanup:
+ b43_gpio_cleanup(dev);
+ goto out;
+}
+
+static void b43_periodic_every120sec(struct b43_wldev *dev)
+{
+ struct b43_phy *phy = &dev->phy;
+
+ if (phy->type != B43_PHYTYPE_G || phy->rev < 2)
+ return;
+
+ b43_mac_suspend(dev);
+ b43_lo_g_measure(dev);
+ b43_mac_enable(dev);
+ if (b43_has_hardware_pctl(phy))
+ b43_lo_g_ctl_mark_all_unused(dev);
+}
+
+static void b43_periodic_every60sec(struct b43_wldev *dev)
+{
+ struct b43_phy *phy = &dev->phy;
+
+ if (!b43_has_hardware_pctl(phy))
+ b43_lo_g_ctl_mark_all_unused(dev);
+ if (dev->dev->bus->sprom.r1.boardflags_lo & B43_BFL_RSSI) {
+ b43_mac_suspend(dev);
+ b43_calc_nrssi_slope(dev);
+ if ((phy->radio_ver == 0x2050) && (phy->radio_rev == 8)) {
+ u8 old_chan = phy->channel;
+
+ /* VCO Calibration */
+ if (old_chan >= 8)
+ b43_radio_selectchannel(dev, 1, 0);
+ else
+ b43_radio_selectchannel(dev, 13, 0);
+ b43_radio_selectchannel(dev, old_chan, 0);
+ }
+ b43_mac_enable(dev);
+ }
+}
+
+static void b43_periodic_every30sec(struct b43_wldev *dev)
+{
+ /* Update device statistics. */
+ b43_calculate_link_quality(dev);
+}
+
+static void b43_periodic_every15sec(struct b43_wldev *dev)
+{
+ struct b43_phy *phy = &dev->phy;
+
+ if (phy->type == B43_PHYTYPE_G) {
+ //TODO: update_aci_moving_average
+ if (phy->aci_enable && phy->aci_wlan_automatic) {
+ b43_mac_suspend(dev);
+ if (!phy->aci_enable && 1 /*TODO: not scanning? */ ) {
+ if (0 /*TODO: bunch of conditions */ ) {
+ b43_radio_set_interference_mitigation
+ (dev, B43_INTERFMODE_MANUALWLAN);
+ }
+ } else if (1 /*TODO*/) {
+ /*
+ if ((aci_average > 1000) && !(b43_radio_aci_scan(dev))) {
+ b43_radio_set_interference_mitigation(dev,
+ B43_INTERFMODE_NONE);
+ }
+ */
+ }
+ b43_mac_enable(dev);
+ } else if (phy->interfmode == B43_INTERFMODE_NONWLAN &&
+ phy->rev == 1) {
+ //TODO: implement rev1 workaround
+ }
+ }
+ b43_phy_xmitpower(dev); //FIXME: unless scanning?
+ //TODO for APHY (temperature?)
+}
+
+static void b43_periodic_every1sec(struct b43_wldev *dev)
+{
+ int radio_hw_enable;
+
+ /* check if radio hardware enabled status changed */
+ radio_hw_enable = b43_is_hw_radio_enabled(dev);
+ if (unlikely(dev->radio_hw_enable != radio_hw_enable)) {
+ dev->radio_hw_enable = radio_hw_enable;
+ b43dbg(dev->wl, "Radio hardware status changed to %s\n",
+ (radio_hw_enable == 0) ? "disabled" : "enabled");
+ b43_leds_update(dev, 0);
+ }
+}
+
+static void do_periodic_work(struct b43_wldev *dev)
+{
+ unsigned int state;
+
+ state = dev->periodic_state;
+ if (state % 120 == 0)
+ b43_periodic_every120sec(dev);
+ if (state % 60 == 0)
+ b43_periodic_every60sec(dev);
+ if (state % 30 == 0)
+ b43_periodic_every30sec(dev);
+ if (state % 15 == 0)
+ b43_periodic_every15sec(dev);
+ b43_periodic_every1sec(dev);
+}
+
+/* Estimate a "Badness" value based on the periodic work
+ * state-machine state. "Badness" is worse (bigger), if the
+ * periodic work will take longer.
+ */
+static int estimate_periodic_work_badness(unsigned int state)
+{
+ int badness = 0;
+
+ if (state % 120 == 0) /* every 120 sec */
+ badness += 10;
+ if (state % 60 == 0) /* every 60 sec */
+ badness += 5;
+ if (state % 30 == 0) /* every 30 sec */
+ badness += 1;
+ if (state % 15 == 0) /* every 15 sec */
+ badness += 1;
+
+#define BADNESS_LIMIT 4
+ return badness;
+}
+
+static void b43_periodic_work_handler(struct work_struct *work)
+{
+ struct b43_wldev *dev =
+ container_of(work, struct b43_wldev, periodic_work.work);
+ unsigned long flags, delay;
+ u32 savedirqs = 0;
+ int badness;
+
+ mutex_lock(&dev->wl->mutex);
+
+ if (unlikely(b43_status(dev) != B43_STAT_STARTED))
+ goto out;
+ if (b43_debug(dev, B43_DBG_PWORK_STOP))
+ goto out_requeue;
+
+ badness = estimate_periodic_work_badness(dev->periodic_state);
+ if (badness > BADNESS_LIMIT) {
+ spin_lock_irqsave(&dev->wl->irq_lock, flags);
+ /* Suspend TX as we don't want to transmit packets while
+ * we recalibrate the hardware. */
+ b43_tx_suspend(dev);
+ savedirqs = b43_interrupt_disable(dev, B43_IRQ_ALL);
+ /* Periodic work will take a long time, so we want it to
+ * be preemtible and release the spinlock. */
+ spin_unlock_irqrestore(&dev->wl->irq_lock, flags);
+ b43_synchronize_irq(dev);
+
+ do_periodic_work(dev);
+
+ spin_lock_irqsave(&dev->wl->irq_lock, flags);
+ b43_interrupt_enable(dev, savedirqs);
+ b43_tx_resume(dev);
+ mmiowb();
+ spin_unlock_irqrestore(&dev->wl->irq_lock, flags);
+ } else {
+ /* Take the global driver lock. This will lock any operation. */
+ spin_lock_irqsave(&dev->wl->irq_lock, flags);
+
+ do_periodic_work(dev);
+
+ mmiowb();
+ spin_unlock_irqrestore(&dev->wl->irq_lock, flags);
+ }
+ dev->periodic_state++;
+ out_requeue:
+ if (b43_debug(dev, B43_DBG_PWORK_FAST))
+ delay = msecs_to_jiffies(50);
+ else
+ delay = round_jiffies(HZ);
+ queue_delayed_work(dev->wl->hw->workqueue, &dev->periodic_work, delay);
+ out:
+ mutex_unlock(&dev->wl->mutex);
+}
+
+static void b43_periodic_tasks_setup(struct b43_wldev *dev)
+{
+ struct delayed_work *work = &dev->periodic_work;
+
+ dev->periodic_state = 0;
+ INIT_DELAYED_WORK(work, b43_periodic_work_handler);
+ queue_delayed_work(dev->wl->hw->workqueue, work, 0);
+}
+
+/* Validate access to the chip (SHM) */
+static int b43_validate_chipaccess(struct b43_wldev *dev)
+{
+ u32 value;
+ u32 shm_backup;
+
+ shm_backup = b43_shm_read32(dev, B43_SHM_SHARED, 0);
+ b43_shm_write32(dev, B43_SHM_SHARED, 0, 0xAA5555AA);
+ if (b43_shm_read32(dev, B43_SHM_SHARED, 0) != 0xAA5555AA)
+ goto error;
+ b43_shm_write32(dev, B43_SHM_SHARED, 0, 0x55AAAA55);
+ if (b43_shm_read32(dev, B43_SHM_SHARED, 0) != 0x55AAAA55)
+ goto error;
+ b43_shm_write32(dev, B43_SHM_SHARED, 0, shm_backup);
+
+ value = b43_read32(dev, B43_MMIO_MACCTL);
+ if ((value | B43_MACCTL_GMODE) !=
+ (B43_MACCTL_GMODE | B43_MACCTL_IHR_ENABLED))
+ goto error;
+
+ value = b43_read32(dev, B43_MMIO_GEN_IRQ_REASON);
+ if (value)
+ goto error;
+
+ return 0;
+ error:
+ b43err(dev->wl, "Failed to validate the chipaccess\n");
+ return -ENODEV;
+}
+
+static void b43_security_init(struct b43_wldev *dev)
+{
+ dev->max_nr_keys = (dev->dev->id.revision >= 5) ? 58 : 20;
+ B43_WARN_ON(dev->max_nr_keys > ARRAY_SIZE(dev->key));
+ dev->ktp = b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_KTP);
+ /* KTP is a word address, but we address SHM bytewise.
+ * So multiply by two.
+ */
+ dev->ktp *= 2;
+ if (dev->dev->id.revision >= 5) {
+ /* Number of RCMTA address slots */
+ b43_write16(dev, B43_MMIO_RCMTA_COUNT, dev->max_nr_keys - 8);
+ }
+ b43_clear_keys(dev);
+}
+
+static int b43_rng_read(struct hwrng *rng, u32 * data)
+{
+ struct b43_wl *wl = (struct b43_wl *)rng->priv;
+ unsigned long flags;
+
+ /* Don't take wl->mutex here, as it could deadlock with
+ * hwrng internal locking. It's not needed to take
+ * wl->mutex here, anyway. */
+
+ spin_lock_irqsave(&wl->irq_lock, flags);
+ *data = b43_read16(wl->current_dev, B43_MMIO_RNG);
+ spin_unlock_irqrestore(&wl->irq_lock, flags);
+
+ return (sizeof(u16));
+}
+
+static void b43_rng_exit(struct b43_wl *wl)
+{
+ if (wl->rng_initialized)
+ hwrng_unregister(&wl->rng);
+}
+
+static int b43_rng_init(struct b43_wl *wl)
+{
+ int err;
+
+ snprintf(wl->rng_name, ARRAY_SIZE(wl->rng_name),
+ "%s_%s", KBUILD_MODNAME, wiphy_name(wl->hw->wiphy));
+ wl->rng.name = wl->rng_name;
+ wl->rng.data_read = b43_rng_read;
+ wl->rng.priv = (unsigned long)wl;
+ wl->rng_initialized = 1;
+ err = hwrng_register(&wl->rng);
+ if (err) {
+ wl->rng_initialized = 0;
+ b43err(wl, "Failed to register the random "
+ "number generator (%d)\n", err);
+ }
+
+ return err;
+}
+
+static int b43_tx(struct ieee80211_hw *hw,
+ struct sk_buff *skb, struct ieee80211_tx_control *ctl)
+{
+ struct b43_wl *wl = hw_to_b43_wl(hw);
+ struct b43_wldev *dev = wl->current_dev;
+ int err = -ENODEV;
+ unsigned long flags;
+
+ if (unlikely(!dev))
+ goto out;
+ if (unlikely(b43_status(dev) < B43_STAT_STARTED))
+ goto out;
+ /* DMA-TX is done without a global lock. */
+ if (b43_using_pio(dev)) {
+ spin_lock_irqsave(&wl->irq_lock, flags);
+ err = b43_pio_tx(dev, skb, ctl);
+ spin_unlock_irqrestore(&wl->irq_lock, flags);
+ } else
+ err = b43_dma_tx(dev, skb, ctl);
+ out:
+ if (unlikely(err))
+ return NETDEV_TX_BUSY;
+ return NETDEV_TX_OK;
+}
+
+static int b43_conf_tx(struct ieee80211_hw *hw,
+ int queue,
+ const struct ieee80211_tx_queue_params *params)
+{
+ return 0;
+}
+
+static int b43_get_tx_stats(struct ieee80211_hw *hw,
+ struct ieee80211_tx_queue_stats *stats)
+{
+ struct b43_wl *wl = hw_to_b43_wl(hw);
+ struct b43_wldev *dev = wl->current_dev;
+ unsigned long flags;
+ int err = -ENODEV;
+
+ if (!dev)
+ goto out;
+ spin_lock_irqsave(&wl->irq_lock, flags);
+ if (likely(b43_status(dev) >= B43_STAT_STARTED)) {
+ if (b43_using_pio(dev))
+ b43_pio_get_tx_stats(dev, stats);
+ else
+ b43_dma_get_tx_stats(dev, stats);
+ err = 0;
+ }
+ spin_unlock_irqrestore(&wl->irq_lock, flags);
+ out:
+ return err;
+}
+
+static int b43_get_stats(struct ieee80211_hw *hw,
+ struct ieee80211_low_level_stats *stats)
+{
+ struct b43_wl *wl = hw_to_b43_wl(hw);
+ unsigned long flags;
+
+ spin_lock_irqsave(&wl->irq_lock, flags);
+ memcpy(stats, &wl->ieee_stats, sizeof(*stats));
+ spin_unlock_irqrestore(&wl->irq_lock, flags);
+
+ return 0;
+}
+
+static const char *phymode_to_string(unsigned int phymode)
+{
+ switch (phymode) {
+ case B43_PHYMODE_A:
+ return "A";
+ case B43_PHYMODE_B:
+ return "B";
+ case B43_PHYMODE_G:
+ return "G";
+ default:
+ B43_WARN_ON(1);
+ }
+ return "";
+}
+
+static int find_wldev_for_phymode(struct b43_wl *wl,
+ unsigned int phymode,
+ struct b43_wldev **dev, bool * gmode)
+{
+ struct b43_wldev *d;
+
+ list_for_each_entry(d, &wl->devlist, list) {
+ if (d->phy.possible_phymodes & phymode) {
+ /* Ok, this device supports the PHY-mode.
+ * Now figure out how the gmode bit has to be
+ * set to support it. */
+ if (phymode == B43_PHYMODE_A)
+ *gmode = 0;
+ else
+ *gmode = 1;
+ *dev = d;
+
+ return 0;
+ }
+ }
+
+ return -ESRCH;
+}
+
+static void b43_put_phy_into_reset(struct b43_wldev *dev)
+{
+ struct ssb_device *sdev = dev->dev;
+ u32 tmslow;
+
+ tmslow = ssb_read32(sdev, SSB_TMSLOW);
+ tmslow &= ~B43_TMSLOW_GMODE;
+ tmslow |= B43_TMSLOW_PHYRESET;
+ tmslow |= SSB_TMSLOW_FGC;
+ ssb_write32(sdev, SSB_TMSLOW, tmslow);
+ msleep(1);
+
+ tmslow = ssb_read32(sdev, SSB_TMSLOW);
+ tmslow &= ~SSB_TMSLOW_FGC;
+ tmslow |= B43_TMSLOW_PHYRESET;
+ ssb_write32(sdev, SSB_TMSLOW, tmslow);
+ msleep(1);
+}
+
+/* Expects wl->mutex locked */
+static int b43_switch_phymode(struct b43_wl *wl, unsigned int new_mode)
+{
+ struct b43_wldev *up_dev;
+ struct b43_wldev *down_dev;
+ int err;
+ bool gmode = 0;
+ int prev_status;
+
+ err = find_wldev_for_phymode(wl, new_mode, &up_dev, &gmode);
+ if (err) {
+ b43err(wl, "Could not find a device for %s-PHY mode\n",
+ phymode_to_string(new_mode));
+ return err;
+ }
+ if ((up_dev == wl->current_dev) &&
+ (!!wl->current_dev->phy.gmode == !!gmode)) {
+ /* This device is already running. */
+ return 0;
+ }
+ b43dbg(wl, "Reconfiguring PHYmode to %s-PHY\n",
+ phymode_to_string(new_mode));
+ down_dev = wl->current_dev;
+
+ prev_status = b43_status(down_dev);
+ /* Shutdown the currently running core. */
+ if (prev_status >= B43_STAT_STARTED)
+ b43_wireless_core_stop(down_dev);
+ if (prev_status >= B43_STAT_INITIALIZED)
+ b43_wireless_core_exit(down_dev);
+
+ if (down_dev != up_dev) {
+ /* We switch to a different core, so we put PHY into
+ * RESET on the old core. */
+ b43_put_phy_into_reset(down_dev);
+ }
+
+ /* Now start the new core. */
+ up_dev->phy.gmode = gmode;
+ if (prev_status >= B43_STAT_INITIALIZED) {
+ err = b43_wireless_core_init(up_dev);
+ if (err) {
+ b43err(wl, "Fatal: Could not initialize device for "
+ "newly selected %s-PHY mode\n",
+ phymode_to_string(new_mode));
+ goto init_failure;
+ }
+ }
+ if (prev_status >= B43_STAT_STARTED) {
+ err = b43_wireless_core_start(up_dev);
+ if (err) {
+ b43err(wl, "Fatal: Coult not start device for "
+ "newly selected %s-PHY mode\n",
+ phymode_to_string(new_mode));
+ b43_wireless_core_exit(up_dev);
+ goto init_failure;
+ }
+ }
+ B43_WARN_ON(b43_status(up_dev) != prev_status);
+
+ wl->current_dev = up_dev;
+
+ return 0;
+ init_failure:
+ /* Whoops, failed to init the new core. No core is operating now. */
+ wl->current_dev = NULL;
+ return err;
+}
+
+static int b43_antenna_from_ieee80211(u8 antenna)
+{
+ switch (antenna) {
+ case 0: /* default/diversity */
+ return B43_ANTENNA_DEFAULT;
+ case 1: /* Antenna 0 */
+ return B43_ANTENNA0;
+ case 2: /* Antenna 1 */
+ return B43_ANTENNA1;
+ default:
+ return B43_ANTENNA_DEFAULT;
+ }
+}
+
+static int b43_dev_config(struct ieee80211_hw *hw, struct ieee80211_conf *conf)
+{
+ struct b43_wl *wl = hw_to_b43_wl(hw);
+ struct b43_wldev *dev;
+ struct b43_phy *phy;
+ unsigned long flags;
+ unsigned int new_phymode = 0xFFFF;
+ int antenna_tx;
+ int antenna_rx;
+ int err = 0;
+ u32 savedirqs;
+
+ antenna_tx = b43_antenna_from_ieee80211(conf->antenna_sel_tx);
+ antenna_rx = b43_antenna_from_ieee80211(conf->antenna_sel_rx);
+
+ mutex_lock(&wl->mutex);
+
+ /* Switch the PHY mode (if necessary). */
+ switch (conf->phymode) {
+ case MODE_IEEE80211A:
+ new_phymode = B43_PHYMODE_A;
+ break;
+ case MODE_IEEE80211B:
+ new_phymode = B43_PHYMODE_B;
+ break;
+ case MODE_IEEE80211G:
+ new_phymode = B43_PHYMODE_G;
+ break;
+ default:
+ B43_WARN_ON(1);
+ }
+ err = b43_switch_phymode(wl, new_phymode);
+ if (err)
+ goto out_unlock_mutex;
+ dev = wl->current_dev;
+ phy = &dev->phy;
+
+ /* Disable IRQs while reconfiguring the device.
+ * This makes it possible to drop the spinlock throughout
+ * the reconfiguration process. */
+ spin_lock_irqsave(&wl->irq_lock, flags);
+ if (b43_status(dev) < B43_STAT_STARTED) {
+ spin_unlock_irqrestore(&wl->irq_lock, flags);
+ goto out_unlock_mutex;
+ }
+ savedirqs = b43_interrupt_disable(dev, B43_IRQ_ALL);
+ spin_unlock_irqrestore(&wl->irq_lock, flags);
+ b43_synchronize_irq(dev);
+
+ /* Switch to the requested channel.
+ * The firmware takes care of races with the TX handler. */
+ if (conf->channel_val != phy->channel)
+ b43_radio_selectchannel(dev, conf->channel_val, 0);
+
+ /* Enable/Disable ShortSlot timing. */
+ if ((!!(conf->flags & IEEE80211_CONF_SHORT_SLOT_TIME)) !=
+ dev->short_slot) {
+ B43_WARN_ON(phy->type != B43_PHYTYPE_G);
+ if (conf->flags & IEEE80211_CONF_SHORT_SLOT_TIME)
+ b43_short_slot_timing_enable(dev);
+ else
+ b43_short_slot_timing_disable(dev);
+ }
+
+ /* Adjust the desired TX power level. */
+ if (conf->power_level != 0) {
+ if (conf->power_level != phy->power_level) {
+ phy->power_level = conf->power_level;
+ b43_phy_xmitpower(dev);
+ }
+ }
+
+ /* Antennas for RX and management frame TX. */
+ b43_mgmtframe_txantenna(dev, antenna_tx);
+ b43_set_rx_antenna(dev, antenna_rx);
+
+ /* Update templates for AP mode. */
+ if (b43_is_mode(wl, IEEE80211_IF_TYPE_AP))
+ b43_set_beacon_int(dev, conf->beacon_int);
+
+ spin_lock_irqsave(&wl->irq_lock, flags);
+ b43_interrupt_enable(dev, savedirqs);
+ mmiowb();
+ spin_unlock_irqrestore(&wl->irq_lock, flags);
+ out_unlock_mutex:
+ mutex_unlock(&wl->mutex);
+
+ return err;
+}
+
+static int b43_dev_set_key(struct ieee80211_hw *hw,
+ set_key_cmd cmd, const u8 *local_addr,
+ const u8 *addr, struct ieee80211_key_conf *key)
+{
+ struct b43_wl *wl = hw_to_b43_wl(hw);
+ struct b43_wldev *dev = wl->current_dev;
+ unsigned long flags;
+ u8 algorithm;
+ u8 index;
+ int err = -EINVAL;
+
+ if (modparam_nohwcrypt)
+ return -ENOSPC; /* User disabled HW-crypto */
+
+ if (!dev)
+ return -ENODEV;
+ switch (key->alg) {
+ case ALG_NONE:
+ algorithm = B43_SEC_ALGO_NONE;
+ break;
+ case ALG_WEP:
+ if (key->keylen == 5)
+ algorithm = B43_SEC_ALGO_WEP40;
+ else
+ algorithm = B43_SEC_ALGO_WEP104;
+ break;
+ case ALG_TKIP:
+ algorithm = B43_SEC_ALGO_TKIP;
+ break;
+ case ALG_CCMP:
+ algorithm = B43_SEC_ALGO_AES;
+ break;
+ default:
+ B43_WARN_ON(1);
+ goto out;
+ }
+
+ index = (u8) (key->keyidx);
+ if (index > 3)
+ goto out;
+
+ mutex_lock(&wl->mutex);
+ spin_lock_irqsave(&wl->irq_lock, flags);
+
+ if (b43_status(dev) < B43_STAT_INITIALIZED) {
+ err = -ENODEV;
+ goto out_unlock;
+ }
+
+ switch (cmd) {
+ case SET_KEY:
+ if (algorithm == B43_SEC_ALGO_TKIP) {
+ /* FIXME: No TKIP hardware encryption for now. */
+ err = -EOPNOTSUPP;
+ goto out_unlock;
+ }
+
+ if (is_broadcast_ether_addr(addr)) {
+ /* addr is FF:FF:FF:FF:FF:FF for default keys */
+ err = b43_key_write(dev, index, algorithm,
+ key->key, key->keylen, NULL, key);
+ } else {
+ /*
+ * either pairwise key or address is 00:00:00:00:00:00
+ * for transmit-only keys
+ */
+ err = b43_key_write(dev, -1, algorithm,
+ key->key, key->keylen, addr, key);
+ }
+ if (err)
+ goto out_unlock;
+
+ if (algorithm == B43_SEC_ALGO_WEP40 ||
+ algorithm == B43_SEC_ALGO_WEP104) {
+ b43_hf_write(dev, b43_hf_read(dev) | B43_HF_USEDEFKEYS);
+ } else {
+ b43_hf_write(dev,
+ b43_hf_read(dev) & ~B43_HF_USEDEFKEYS);
+ }
+ key->flags |= IEEE80211_KEY_FLAG_GENERATE_IV;
+ break;
+ case DISABLE_KEY: {
+ err = b43_key_clear(dev, key->hw_key_idx);
+ if (err)
+ goto out_unlock;
+ break;
+ }
+ default:
+ B43_WARN_ON(1);
+ }
+out_unlock:
+ spin_unlock_irqrestore(&wl->irq_lock, flags);
+ mutex_unlock(&wl->mutex);
+out:
+ if (!err) {
+ b43dbg(wl, "%s hardware based encryption for keyidx: %d, "
+ "mac: " MAC_FMT "\n",
+ cmd == SET_KEY ? "Using" : "Disabling", key->keyidx,
+ MAC_ARG(addr));
+ }
+ return err;
+}
+
+static void b43_set_multicast_list(struct ieee80211_hw *hw,
+ unsigned short netflags, int mc_count)
+{
+ struct b43_wl *wl = hw_to_b43_wl(hw);
+ struct b43_wldev *dev = wl->current_dev;
+ unsigned long flags;
+
+ if (!dev)
+ return;
+ spin_lock_irqsave(&wl->irq_lock, flags);
+ if (wl->promisc != !!(netflags & IFF_PROMISC)) {
+ wl->promisc = !!(netflags & IFF_PROMISC);
+ if (b43_status(dev) >= B43_STAT_INITIALIZED)
+ b43_adjust_opmode(dev);
+ }
+ spin_unlock_irqrestore(&wl->irq_lock, flags);
+}
+
+static int b43_config_interface(struct ieee80211_hw *hw,
+ int if_id, struct ieee80211_if_conf *conf)
+{
+ struct b43_wl *wl = hw_to_b43_wl(hw);
+ struct b43_wldev *dev = wl->current_dev;
+ unsigned long flags;
+
+ if (!dev)
+ return -ENODEV;
+ mutex_lock(&wl->mutex);
+ spin_lock_irqsave(&wl->irq_lock, flags);
+ if (conf->type != IEEE80211_IF_TYPE_MNTR) {
+ B43_WARN_ON(wl->if_id != if_id);
+ if (conf->bssid)
+ memcpy(wl->bssid, conf->bssid, ETH_ALEN);
+ else
+ memset(wl->bssid, 0, ETH_ALEN);
+ if (b43_status(dev) >= B43_STAT_INITIALIZED) {
+ if (b43_is_mode(wl, IEEE80211_IF_TYPE_AP)) {
+ B43_WARN_ON(conf->type != IEEE80211_IF_TYPE_AP);
+ b43_set_ssid(dev, conf->ssid, conf->ssid_len);
+ if (conf->beacon)
+ b43_refresh_templates(dev, conf->beacon);
+ }
+ b43_write_mac_bssid_templates(dev);
+ }
+ }
+ spin_unlock_irqrestore(&wl->irq_lock, flags);
+ mutex_unlock(&wl->mutex);
+
+ return 0;
+}
+
+/* Locking: wl->mutex */
+static void b43_wireless_core_stop(struct b43_wldev *dev)
+{
+ struct b43_wl *wl = dev->wl;
+ unsigned long flags;
+
+ if (b43_status(dev) < B43_STAT_STARTED)
+ return;
+ b43_set_status(dev, B43_STAT_INITIALIZED);
+
+ mutex_unlock(&wl->mutex);
+ /* Must unlock as it would otherwise deadlock. No races here.
+ * Cancel the possibly running self-rearming periodic work. */
+ cancel_delayed_work_sync(&dev->periodic_work);
+ mutex_lock(&wl->mutex);
+
+ ieee80211_stop_queues(wl->hw); //FIXME this could cause a deadlock, as mac80211 seems buggy.
+
+ /* Disable and sync interrupts. */
+ spin_lock_irqsave(&wl->irq_lock, flags);
+ dev->irq_savedstate = b43_interrupt_disable(dev, B43_IRQ_ALL);
+ b43_read32(dev, B43_MMIO_GEN_IRQ_MASK); /* flush */
+ spin_unlock_irqrestore(&wl->irq_lock, flags);
+ b43_synchronize_irq(dev);
+
+ b43_mac_suspend(dev);
+ free_irq(dev->dev->irq, dev);
+ b43dbg(wl, "Wireless interface stopped\n");
+}
+
+/* Locking: wl->mutex */
+static int b43_wireless_core_start(struct b43_wldev *dev)
+{
+ int err;
+
+ B43_WARN_ON(b43_status(dev) != B43_STAT_INITIALIZED);
+
+ drain_txstatus_queue(dev);
+ err = request_irq(dev->dev->irq, b43_interrupt_handler,
+ IRQF_SHARED, KBUILD_MODNAME, dev);
+ if (err) {
+ b43err(dev->wl, "Cannot request IRQ-%d\n", dev->dev->irq);
+ goto out;
+ }
+
+ /* We are ready to run. */
+ b43_set_status(dev, B43_STAT_STARTED);
+
+ /* Start data flow (TX/RX). */
+ b43_mac_enable(dev);
+ b43_interrupt_enable(dev, dev->irq_savedstate);
+ ieee80211_start_queues(dev->wl->hw);
+
+ /* Start maintainance work */
+ b43_periodic_tasks_setup(dev);
+
+ b43dbg(dev->wl, "Wireless interface started\n");
+ out:
+ return err;
+}
+
+/* Get PHY and RADIO versioning numbers */
+static int b43_phy_versioning(struct b43_wldev *dev)
+{
+ struct b43_phy *phy = &dev->phy;
+ u32 tmp;
+ u8 analog_type;
+ u8 phy_type;
+ u8 phy_rev;
+ u16 radio_manuf;
+ u16 radio_ver;
+ u16 radio_rev;
+ int unsupported = 0;
+
+ /* Get PHY versioning */
+ tmp = b43_read16(dev, B43_MMIO_PHY_VER);
+ analog_type = (tmp & B43_PHYVER_ANALOG) >> B43_PHYVER_ANALOG_SHIFT;
+ phy_type = (tmp & B43_PHYVER_TYPE) >> B43_PHYVER_TYPE_SHIFT;
+ phy_rev = (tmp & B43_PHYVER_VERSION);
+ switch (phy_type) {
+ case B43_PHYTYPE_A:
+ if (phy_rev >= 4)
+ unsupported = 1;
+ break;
+ case B43_PHYTYPE_B:
+ if (phy_rev != 2 && phy_rev != 4 && phy_rev != 6
+ && phy_rev != 7)
+ unsupported = 1;
+ break;
+ case B43_PHYTYPE_G:
+ if (phy_rev > 8)
+ unsupported = 1;
+ break;
+ default:
+ unsupported = 1;
+ };
+ if (unsupported) {
+ b43err(dev->wl, "FOUND UNSUPPORTED PHY "
+ "(Analog %u, Type %u, Revision %u)\n",
+ analog_type, phy_type, phy_rev);
+ return -EOPNOTSUPP;
+ }
+ b43dbg(dev->wl, "Found PHY: Analog %u, Type %u, Revision %u\n",
+ analog_type, phy_type, phy_rev);
+
+ /* Get RADIO versioning */
+ if (dev->dev->bus->chip_id == 0x4317) {
+ if (dev->dev->bus->chip_rev == 0)
+ tmp = 0x3205017F;
+ else if (dev->dev->bus->chip_rev == 1)
+ tmp = 0x4205017F;
+ else
+ tmp = 0x5205017F;
+ } else {
+ b43_write16(dev, B43_MMIO_RADIO_CONTROL, B43_RADIOCTL_ID);
+ tmp = b43_read16(dev, B43_MMIO_RADIO_DATA_HIGH);
+ tmp <<= 16;
+ b43_write16(dev, B43_MMIO_RADIO_CONTROL, B43_RADIOCTL_ID);
+ tmp |= b43_read16(dev, B43_MMIO_RADIO_DATA_LOW);
+ }
+ radio_manuf = (tmp & 0x00000FFF);
+ radio_ver = (tmp & 0x0FFFF000) >> 12;
+ radio_rev = (tmp & 0xF0000000) >> 28;
+ switch (phy_type) {
+ case B43_PHYTYPE_A:
+ if (radio_ver != 0x2060)
+ unsupported = 1;
+ if (radio_rev != 1)
+ unsupported = 1;
+ if (radio_manuf != 0x17F)
+ unsupported = 1;
+ break;
+ case B43_PHYTYPE_B:
+ if ((radio_ver & 0xFFF0) != 0x2050)
+ unsupported = 1;
+ break;
+ case B43_PHYTYPE_G:
+ if (radio_ver != 0x2050)
+ unsupported = 1;
+ break;
+ default:
+ B43_WARN_ON(1);
+ }
+ if (unsupported) {
+ b43err(dev->wl, "FOUND UNSUPPORTED RADIO "
+ "(Manuf 0x%X, Version 0x%X, Revision %u)\n",
+ radio_manuf, radio_ver, radio_rev);
+ return -EOPNOTSUPP;
+ }
+ b43dbg(dev->wl, "Found Radio: Manuf 0x%X, Version 0x%X, Revision %u\n",
+ radio_manuf, radio_ver, radio_rev);
+
+ phy->radio_manuf = radio_manuf;
+ phy->radio_ver = radio_ver;
+ phy->radio_rev = radio_rev;
+
+ phy->analog = analog_type;
+ phy->type = phy_type;
+ phy->rev = phy_rev;
+
+ return 0;
+}
+
+static void setup_struct_phy_for_init(struct b43_wldev *dev,
+ struct b43_phy *phy)
+{
+ struct b43_txpower_lo_control *lo;
+ int i;
+
+ memset(phy->minlowsig, 0xFF, sizeof(phy->minlowsig));
+ memset(phy->minlowsigpos, 0, sizeof(phy->minlowsigpos));
+
+ /* Flags */
+ phy->locked = 0;
+
+ phy->aci_enable = 0;
+ phy->aci_wlan_automatic = 0;
+ phy->aci_hw_rssi = 0;
+
+ lo = phy->lo_control;
+ if (lo) {
+ memset(lo, 0, sizeof(*(phy->lo_control)));
+ lo->rebuild = 1;
+ lo->tx_bias = 0xFF;
+ }
+ phy->max_lb_gain = 0;
+ phy->trsw_rx_gain = 0;
+ phy->txpwr_offset = 0;
+
+ /* NRSSI */
+ phy->nrssislope = 0;
+ for (i = 0; i < ARRAY_SIZE(phy->nrssi); i++)
+ phy->nrssi[i] = -1000;
+ for (i = 0; i < ARRAY_SIZE(phy->nrssi_lt); i++)
+ phy->nrssi_lt[i] = i;
+
+ phy->lofcal = 0xFFFF;
+ phy->initval = 0xFFFF;
+
+ spin_lock_init(&phy->lock);
+ phy->interfmode = B43_INTERFMODE_NONE;
+ phy->channel = 0xFF;
+
+ phy->hardware_power_control = !!modparam_hwpctl;
+}
+
+static void setup_struct_wldev_for_init(struct b43_wldev *dev)
+{
+ /* Flags */
+ dev->reg124_set_0x4 = 0;
+
+ /* Stats */
+ memset(&dev->stats, 0, sizeof(dev->stats));
+
+ setup_struct_phy_for_init(dev, &dev->phy);
+
+ /* IRQ related flags */
+ dev->irq_reason = 0;
+ memset(dev->dma_reason, 0, sizeof(dev->dma_reason));
+ dev->irq_savedstate = B43_IRQ_MASKTEMPLATE;
+
+ dev->mac_suspended = 1;
+
+ /* Noise calculation context */
+ memset(&dev->noisecalc, 0, sizeof(dev->noisecalc));
+}
+
+static void b43_bluetooth_coext_enable(struct b43_wldev *dev)
+{
+ struct ssb_sprom *sprom = &dev->dev->bus->sprom;
+ u32 hf;
+
+ if (!(sprom->r1.boardflags_lo & B43_BFL_BTCOEXIST))
+ return;
+ if (dev->phy.type != B43_PHYTYPE_B && !dev->phy.gmode)
+ return;
+
+ hf = b43_hf_read(dev);
+ if (sprom->r1.boardflags_lo & B43_BFL_BTCMOD)
+ hf |= B43_HF_BTCOEXALT;
+ else
+ hf |= B43_HF_BTCOEX;
+ b43_hf_write(dev, hf);
+ //TODO
+}
+
+static void b43_bluetooth_coext_disable(struct b43_wldev *dev)
+{ //TODO
+}
+
+static void b43_imcfglo_timeouts_workaround(struct b43_wldev *dev)
+{
+#ifdef CONFIG_SSB_DRIVER_PCICORE
+ struct ssb_bus *bus = dev->dev->bus;
+ u32 tmp;
+
+ if (bus->pcicore.dev &&
+ bus->pcicore.dev->id.coreid == SSB_DEV_PCI &&
+ bus->pcicore.dev->id.revision <= 5) {
+ /* IMCFGLO timeouts workaround. */
+ tmp = ssb_read32(dev->dev, SSB_IMCFGLO);
+ tmp &= ~SSB_IMCFGLO_REQTO;
+ tmp &= ~SSB_IMCFGLO_SERTO;
+ switch (bus->bustype) {
+ case SSB_BUSTYPE_PCI:
+ case SSB_BUSTYPE_PCMCIA:
+ tmp |= 0x32;
+ break;
+ case SSB_BUSTYPE_SSB:
+ tmp |= 0x53;
+ break;
+ }
+ ssb_write32(dev->dev, SSB_IMCFGLO, tmp);
+ }
+#endif /* CONFIG_SSB_DRIVER_PCICORE */
+}
+
+/* Shutdown a wireless core */
+/* Locking: wl->mutex */
+static void b43_wireless_core_exit(struct b43_wldev *dev)
+{
+ struct b43_phy *phy = &dev->phy;
+
+ B43_WARN_ON(b43_status(dev) > B43_STAT_INITIALIZED);
+ if (b43_status(dev) != B43_STAT_INITIALIZED)
+ return;
+ b43_set_status(dev, B43_STAT_UNINIT);
+
+ b43_rng_exit(dev->wl);
+ b43_pio_free(dev);
+ b43_dma_free(dev);
+ b43_chip_exit(dev);
+ b43_radio_turn_off(dev);
+ b43_switch_analog(dev, 0);
+ if (phy->dyn_tssi_tbl)
+ kfree(phy->tssi2dbm);
+ kfree(phy->lo_control);
+ phy->lo_control = NULL;
+ ssb_device_disable(dev->dev, 0);
+ ssb_bus_may_powerdown(dev->dev->bus);
+}
+
+/* Initialize a wireless core */
+static int b43_wireless_core_init(struct b43_wldev *dev)
+{
+ struct b43_wl *wl = dev->wl;
+ struct ssb_bus *bus = dev->dev->bus;
+ struct ssb_sprom *sprom = &bus->sprom;
+ struct b43_phy *phy = &dev->phy;
+ int err;
+ u32 hf, tmp;
+
+ B43_WARN_ON(b43_status(dev) != B43_STAT_UNINIT);
+
+ err = ssb_bus_powerup(bus, 0);
+ if (err)
+ goto out;
+ if (!ssb_device_is_enabled(dev->dev)) {
+ tmp = phy->gmode ? B43_TMSLOW_GMODE : 0;
+ b43_wireless_core_reset(dev, tmp);
+ }
+
+ if ((phy->type == B43_PHYTYPE_B) || (phy->type == B43_PHYTYPE_G)) {
+ phy->lo_control =
+ kzalloc(sizeof(*(phy->lo_control)), GFP_KERNEL);
+ if (!phy->lo_control) {
+ err = -ENOMEM;
+ goto err_busdown;
+ }
+ }
+ setup_struct_wldev_for_init(dev);
+
+ err = b43_phy_init_tssi2dbm_table(dev);
+ if (err)
+ goto err_kfree_lo_control;
+
+ /* Enable IRQ routing to this device. */
+ ssb_pcicore_dev_irqvecs_enable(&bus->pcicore, dev->dev);
+
+ b43_imcfglo_timeouts_workaround(dev);
+ b43_bluetooth_coext_disable(dev);
+ b43_phy_early_init(dev);
+ err = b43_chip_init(dev);
+ if (err)
+ goto err_kfree_tssitbl;
+ b43_shm_write16(dev, B43_SHM_SHARED,
+ B43_SHM_SH_WLCOREREV, dev->dev->id.revision);
+ hf = b43_hf_read(dev);
+ if (phy->type == B43_PHYTYPE_G) {
+ hf |= B43_HF_SYMW;
+ if (phy->rev == 1)
+ hf |= B43_HF_GDCW;
+ if (sprom->r1.boardflags_lo & B43_BFL_PACTRL)
+ hf |= B43_HF_OFDMPABOOST;
+ } else if (phy->type == B43_PHYTYPE_B) {
+ hf |= B43_HF_SYMW;
+ if (phy->rev >= 2 && phy->radio_ver == 0x2050)
+ hf &= ~B43_HF_GDCW;
+ }
+ b43_hf_write(dev, hf);
+
+ /* Short/Long Retry Limit.
+ * The retry-limit is a 4-bit counter. Enforce this to avoid overflowing
+ * the chip-internal counter.
+ */
+ tmp = limit_value(modparam_short_retry, 0, 0xF);
+ b43_shm_write16(dev, B43_SHM_SCRATCH, B43_SHM_SC_SRLIMIT, tmp);
+ tmp = limit_value(modparam_long_retry, 0, 0xF);
+ b43_shm_write16(dev, B43_SHM_SCRATCH, B43_SHM_SC_LRLIMIT, tmp);
+
+ b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_SFFBLIM, 3);
+ b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_LFFBLIM, 2);
+
+ /* Disable sending probe responses from firmware.
+ * Setting the MaxTime to one usec will always trigger
+ * a timeout, so we never send any probe resp.
+ * A timeout of zero is infinite. */
+ b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_PRMAXTIME, 1);
+
+ b43_rate_memory_init(dev);
+
+ /* Minimum Contention Window */
+ if (phy->type == B43_PHYTYPE_B) {
+ b43_shm_write16(dev, B43_SHM_SCRATCH, B43_SHM_SC_MINCONT, 0x1F);
+ } else {
+ b43_shm_write16(dev, B43_SHM_SCRATCH, B43_SHM_SC_MINCONT, 0xF);
+ }
+ /* Maximum Contention Window */
+ b43_shm_write16(dev, B43_SHM_SCRATCH, B43_SHM_SC_MAXCONT, 0x3FF);
+
+ do {
+ if (b43_using_pio(dev)) {
+ err = b43_pio_init(dev);
+ } else {
+ err = b43_dma_init(dev);
+ if (!err)
+ b43_qos_init(dev);
+ }
+ } while (err == -EAGAIN);
+ if (err)
+ goto err_chip_exit;
+
+//FIXME
+#if 1
+ b43_write16(dev, 0x0612, 0x0050);
+ b43_shm_write16(dev, B43_SHM_SHARED, 0x0416, 0x0050);
+ b43_shm_write16(dev, B43_SHM_SHARED, 0x0414, 0x01F4);
+#endif
+
+ b43_bluetooth_coext_enable(dev);
+
+ ssb_bus_powerup(bus, 1); /* Enable dynamic PCTL */
+ memset(wl->bssid, 0, ETH_ALEN);
+ b43_upload_card_macaddress(dev, NULL);
+ b43_security_init(dev);
+ b43_rng_init(wl);
+
+ b43_set_status(dev, B43_STAT_INITIALIZED);
+
+ out:
+ return err;
+
+ err_chip_exit:
+ b43_chip_exit(dev);
+ err_kfree_tssitbl:
+ if (phy->dyn_tssi_tbl)
+ kfree(phy->tssi2dbm);
+ err_kfree_lo_control:
+ kfree(phy->lo_control);
+ phy->lo_control = NULL;
+ err_busdown:
+ ssb_bus_may_powerdown(bus);
+ B43_WARN_ON(b43_status(dev) != B43_STAT_UNINIT);
+ return err;
+}
+
+static int b43_add_interface(struct ieee80211_hw *hw,
+ struct ieee80211_if_init_conf *conf)
+{
+ struct b43_wl *wl = hw_to_b43_wl(hw);
+ struct b43_wldev *dev;
+ unsigned long flags;
+ int err = -EOPNOTSUPP;
+ int did_init = 0;
+
+ mutex_lock(&wl->mutex);
+ if ((conf->type != IEEE80211_IF_TYPE_MNTR) && wl->operating)
+ goto out_mutex_unlock;
+
+ b43dbg(wl, "Adding Interface type %d\n", conf->type);
+
+ dev = wl->current_dev;
+ if (b43_status(dev) < B43_STAT_INITIALIZED) {
+ err = b43_wireless_core_init(dev);
+ if (err)
+ goto out_mutex_unlock;
+ did_init = 1;
+ }
+ if (b43_status(dev) < B43_STAT_STARTED) {
+ err = b43_wireless_core_start(dev);
+ if (err) {
+ if (did_init)
+ b43_wireless_core_exit(dev);
+ goto out_mutex_unlock;
+ }
+ }
+
+ spin_lock_irqsave(&wl->irq_lock, flags);
+ switch (conf->type) {
+ case IEEE80211_IF_TYPE_MNTR:
+ wl->monitor++;
+ break;
+ default:
+ wl->operating = 1;
+ wl->if_id = conf->if_id;
+ wl->if_type = conf->type;
+ b43_upload_card_macaddress(dev, conf->mac_addr);
+ }
+ b43_adjust_opmode(dev);
+ spin_unlock_irqrestore(&wl->irq_lock, flags);
+
+ err = 0;
+ out_mutex_unlock:
+ mutex_unlock(&wl->mutex);
+
+ return err;
+}
+
+static void b43_remove_interface(struct ieee80211_hw *hw,
+ struct ieee80211_if_init_conf *conf)
+{
+ struct b43_wl *wl = hw_to_b43_wl(hw);
+ struct b43_wldev *dev;
+ unsigned long flags;
+
+ b43dbg(wl, "Removing Interface type %d\n", conf->type);
+
+ mutex_lock(&wl->mutex);
+ if (conf->type == IEEE80211_IF_TYPE_MNTR) {
+ wl->monitor--;
+ B43_WARN_ON(wl->monitor < 0);
+ } else {
+ B43_WARN_ON(!wl->operating);
+ wl->operating = 0;
+ }
+
+ dev = wl->current_dev;
+ if (!wl->operating && wl->monitor == 0) {
+ /* No interface left. */
+ if (b43_status(dev) >= B43_STAT_STARTED)
+ b43_wireless_core_stop(dev);
+ b43_wireless_core_exit(dev);
+ } else {
+ /* Just monitor interfaces left. */
+ spin_lock_irqsave(&wl->irq_lock, flags);
+ b43_adjust_opmode(dev);
+ if (!wl->operating)
+ b43_upload_card_macaddress(dev, NULL);
+ spin_unlock_irqrestore(&wl->irq_lock, flags);
+ }
+ mutex_unlock(&wl->mutex);
+}
+
+static const struct ieee80211_ops b43_hw_ops = {
+ .tx = b43_tx,
+ .conf_tx = b43_conf_tx,
+ .add_interface = b43_add_interface,
+ .remove_interface = b43_remove_interface,
+ .config = b43_dev_config,
+ .config_interface = b43_config_interface,
+ .set_multicast_list = b43_set_multicast_list,
+ .set_key = b43_dev_set_key,
+ .get_stats = b43_get_stats,
+ .get_tx_stats = b43_get_tx_stats,
+};
+
+/* Hard-reset the chip. Do not call this directly.
+ * Use b43_controller_restart()
+ */
+static void b43_chip_reset(struct work_struct *work)
+{
+ struct b43_wldev *dev =
+ container_of(work, struct b43_wldev, restart_work);
+ struct b43_wl *wl = dev->wl;
+ int err = 0;
+ int prev_status;
+
+ mutex_lock(&wl->mutex);
+
+ prev_status = b43_status(dev);
+ /* Bring the device down... */
+ if (prev_status >= B43_STAT_STARTED)
+ b43_wireless_core_stop(dev);
+ if (prev_status >= B43_STAT_INITIALIZED)
+ b43_wireless_core_exit(dev);
+
+ /* ...and up again. */
+ if (prev_status >= B43_STAT_INITIALIZED) {
+ err = b43_wireless_core_init(dev);
+ if (err)
+ goto out;
+ }
+ if (prev_status >= B43_STAT_STARTED) {
+ err = b43_wireless_core_start(dev);
+ if (err) {
+ b43_wireless_core_exit(dev);
+ goto out;
+ }
+ }
+ out:
+ mutex_unlock(&wl->mutex);
+ if (err)
+ b43err(wl, "Controller restart FAILED\n");
+ else
+ b43info(wl, "Controller restarted\n");
+}
+
+static int b43_setup_modes(struct b43_wldev *dev,
+ int have_aphy, int have_bphy, int have_gphy)
+{
+ struct ieee80211_hw *hw = dev->wl->hw;
+ struct ieee80211_hw_mode *mode;
+ struct b43_phy *phy = &dev->phy;
+ int cnt = 0;
+ int err;
+
+/*FIXME: Don't tell ieee80211 about an A-PHY, because we currently don't support A-PHY. */
+ have_aphy = 0;
+
+ phy->possible_phymodes = 0;
+ for (; 1; cnt++) {
+ if (have_aphy) {
+ B43_WARN_ON(cnt >= B43_MAX_PHYHWMODES);
+ mode = &phy->hwmodes[cnt];
+
+ mode->mode = MODE_IEEE80211A;
+ mode->num_channels = b43_a_chantable_size;
+ mode->channels = b43_a_chantable;
+ mode->num_rates = b43_a_ratetable_size;
+ mode->rates = b43_a_ratetable;
+ err = ieee80211_register_hwmode(hw, mode);
+ if (err)
+ return err;
+
+ phy->possible_phymodes |= B43_PHYMODE_A;
+ have_aphy = 0;
+ continue;
+ }
+ if (have_bphy) {
+ B43_WARN_ON(cnt >= B43_MAX_PHYHWMODES);
+ mode = &phy->hwmodes[cnt];
+
+ mode->mode = MODE_IEEE80211B;
+ mode->num_channels = b43_bg_chantable_size;
+ mode->channels = b43_bg_chantable;
+ mode->num_rates = b43_b_ratetable_size;
+ mode->rates = b43_b_ratetable;
+ err = ieee80211_register_hwmode(hw, mode);
+ if (err)
+ return err;
+
+ phy->possible_phymodes |= B43_PHYMODE_B;
+ have_bphy = 0;
+ continue;
+ }
+ if (have_gphy) {
+ B43_WARN_ON(cnt >= B43_MAX_PHYHWMODES);
+ mode = &phy->hwmodes[cnt];
+
+ mode->mode = MODE_IEEE80211G;
+ mode->num_channels = b43_bg_chantable_size;
+ mode->channels = b43_bg_chantable;
+ mode->num_rates = b43_g_ratetable_size;
+ mode->rates = b43_g_ratetable;
+ err = ieee80211_register_hwmode(hw, mode);
+ if (err)
+ return err;
+
+ phy->possible_phymodes |= B43_PHYMODE_G;
+ have_gphy = 0;
+ continue;
+ }
+ break;
+ }
+
+ return 0;
+}
+
+static void b43_wireless_core_detach(struct b43_wldev *dev)
+{
+ /* We release firmware that late to not be required to re-request
+ * is all the time when we reinit the core. */
+ b43_release_firmware(dev);
+}
+
+static int b43_wireless_core_attach(struct b43_wldev *dev)
+{
+ struct b43_wl *wl = dev->wl;
+ struct ssb_bus *bus = dev->dev->bus;
+ struct pci_dev *pdev = bus->host_pci;
+ int err;
+ int have_aphy = 0, have_bphy = 0, have_gphy = 0;
+ u32 tmp;
+
+ /* Do NOT do any device initialization here.
+ * Do it in wireless_core_init() instead.
+ * This function is for gathering basic information about the HW, only.
+ * Also some structs may be set up here. But most likely you want to have
+ * that in core_init(), too.
+ */
+
+ err = ssb_bus_powerup(bus, 0);
+ if (err) {
+ b43err(wl, "Bus powerup failed\n");
+ goto out;
+ }
+ /* Get the PHY type. */
+ if (dev->dev->id.revision >= 5) {
+ u32 tmshigh;
+
+ tmshigh = ssb_read32(dev->dev, SSB_TMSHIGH);
+ have_aphy = !!(tmshigh & B43_TMSHIGH_APHY);
+ have_gphy = !!(tmshigh & B43_TMSHIGH_GPHY);
+ if (!have_aphy && !have_gphy)
+ have_bphy = 1;
+ } else if (dev->dev->id.revision == 4) {
+ have_gphy = 1;
+ have_aphy = 1;
+ } else
+ have_bphy = 1;
+
+ /* Initialize LEDs structs. */
+ err = b43_leds_init(dev);
+ if (err)
+ goto err_powerdown;
+
+ dev->phy.gmode = (have_gphy || have_bphy);
+ tmp = dev->phy.gmode ? B43_TMSLOW_GMODE : 0;
+ b43_wireless_core_reset(dev, tmp);
+
+ err = b43_phy_versioning(dev);
+ if (err)
+ goto err_leds_exit;
+ /* Check if this device supports multiband. */
+ if (!pdev ||
+ (pdev->device != 0x4312 &&
+ pdev->device != 0x4319 && pdev->device != 0x4324)) {
+ /* No multiband support. */
+ have_aphy = 0;
+ have_bphy = 0;
+ have_gphy = 0;
+ switch (dev->phy.type) {
+ case B43_PHYTYPE_A:
+ have_aphy = 1;
+ break;
+ case B43_PHYTYPE_B:
+ have_bphy = 1;
+ break;
+ case B43_PHYTYPE_G:
+ have_gphy = 1;
+ break;
+ default:
+ B43_WARN_ON(1);
+ }
+ }
+ dev->phy.gmode = (have_gphy || have_bphy);
+ tmp = dev->phy.gmode ? B43_TMSLOW_GMODE : 0;
+ b43_wireless_core_reset(dev, tmp);
+
+ err = b43_validate_chipaccess(dev);
+ if (err)
+ goto err_leds_exit;
+ err = b43_setup_modes(dev, have_aphy, have_bphy, have_gphy);
+ if (err)
+ goto err_leds_exit;
+
+ /* Now set some default "current_dev" */
+ if (!wl->current_dev)
+ wl->current_dev = dev;
+ INIT_WORK(&dev->restart_work, b43_chip_reset);
+
+ b43_radio_turn_off(dev);
+ b43_switch_analog(dev, 0);
+ ssb_device_disable(dev->dev, 0);
+ ssb_bus_may_powerdown(bus);
+
+out:
+ return err;
+
+err_leds_exit:
+ b43_leds_exit(dev);
+err_powerdown:
+ ssb_bus_may_powerdown(bus);
+ return err;
+}
+
+static void b43_one_core_detach(struct ssb_device *dev)
+{
+ struct b43_wldev *wldev;
+ struct b43_wl *wl;
+
+ wldev = ssb_get_drvdata(dev);
+ wl = wldev->wl;
+ cancel_work_sync(&wldev->restart_work);
+ b43_debugfs_remove_device(wldev);
+ b43_wireless_core_detach(wldev);
+ list_del(&wldev->list);
+ wl->nr_devs--;
+ ssb_set_drvdata(dev, NULL);
+ kfree(wldev);
+}
+
+static int b43_one_core_attach(struct ssb_device *dev, struct b43_wl *wl)
+{
+ struct b43_wldev *wldev;
+ struct pci_dev *pdev;
+ int err = -ENOMEM;
+
+ if (!list_empty(&wl->devlist)) {
+ /* We are not the first core on this chip. */
+ pdev = dev->bus->host_pci;
+ /* Only special chips support more than one wireless
+ * core, although some of the other chips have more than
+ * one wireless core as well. Check for this and
+ * bail out early.
+ */
+ if (!pdev ||
+ ((pdev->device != 0x4321) &&
+ (pdev->device != 0x4313) && (pdev->device != 0x431A))) {
+ b43dbg(wl, "Ignoring unconnected 802.11 core\n");
+ return -ENODEV;
+ }
+ }
+
+ wldev = kzalloc(sizeof(*wldev), GFP_KERNEL);
+ if (!wldev)
+ goto out;
+
+ wldev->dev = dev;
+ wldev->wl = wl;
+ b43_set_status(wldev, B43_STAT_UNINIT);
+ wldev->bad_frames_preempt = modparam_bad_frames_preempt;
+ tasklet_init(&wldev->isr_tasklet,
+ (void (*)(unsigned long))b43_interrupt_tasklet,
+ (unsigned long)wldev);
+ if (modparam_pio)
+ wldev->__using_pio = 1;
+ INIT_LIST_HEAD(&wldev->list);
+
+ err = b43_wireless_core_attach(wldev);
+ if (err)
+ goto err_kfree_wldev;
+
+ list_add(&wldev->list, &wl->devlist);
+ wl->nr_devs++;
+ ssb_set_drvdata(dev, wldev);
+ b43_debugfs_add_device(wldev);
+
+ out:
+ return err;
+
+ err_kfree_wldev:
+ kfree(wldev);
+ return err;
+}
+
+static void b43_sprom_fixup(struct ssb_bus *bus)
+{
+ /* boardflags workarounds */
+ if (bus->boardinfo.vendor == SSB_BOARDVENDOR_DELL &&
+ bus->chip_id == 0x4301 && bus->boardinfo.rev == 0x74)
+ bus->sprom.r1.boardflags_lo |= B43_BFL_BTCOEXIST;
+ if (bus->boardinfo.vendor == PCI_VENDOR_ID_APPLE &&
+ bus->boardinfo.type == 0x4E && bus->boardinfo.rev > 0x40)
+ bus->sprom.r1.boardflags_lo |= B43_BFL_PACTRL;
+
+ /* Handle case when gain is not set in sprom */
+ if (bus->sprom.r1.antenna_gain_a == 0xFF)
+ bus->sprom.r1.antenna_gain_a = 2;
+ if (bus->sprom.r1.antenna_gain_bg == 0xFF)
+ bus->sprom.r1.antenna_gain_bg = 2;
+
+ /* Convert Antennagain values to Q5.2 */
+ bus->sprom.r1.antenna_gain_a <<= 2;
+ bus->sprom.r1.antenna_gain_bg <<= 2;
+}
+
+static void b43_wireless_exit(struct ssb_device *dev, struct b43_wl *wl)
+{
+ struct ieee80211_hw *hw = wl->hw;
+
+ ssb_set_devtypedata(dev, NULL);
+ ieee80211_free_hw(hw);
+}
+
+static int b43_wireless_init(struct ssb_device *dev)
+{
+ struct ssb_sprom *sprom = &dev->bus->sprom;
+ struct ieee80211_hw *hw;
+ struct b43_wl *wl;
+ int err = -ENOMEM;
+
+ b43_sprom_fixup(dev->bus);
+
+ hw = ieee80211_alloc_hw(sizeof(*wl), &b43_hw_ops);
+ if (!hw) {
+ b43err(NULL, "Could not allocate ieee80211 device\n");
+ goto out;
+ }
+
+ /* fill hw info */
+ hw->flags = IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE |
+ IEEE80211_HW_MONITOR_DURING_OPER;
+ hw->max_signal = 100;
+ hw->max_rssi = -110;
+ hw->max_noise = -110;
+ hw->queues = 1; /* FIXME: hardware has more queues */
+ SET_IEEE80211_DEV(hw, dev->dev);
+ if (is_valid_ether_addr(sprom->r1.et1mac))
+ SET_IEEE80211_PERM_ADDR(hw, sprom->r1.et1mac);
+ else
+ SET_IEEE80211_PERM_ADDR(hw, sprom->r1.il0mac);
+
+ /* Get and initialize struct b43_wl */
+ wl = hw_to_b43_wl(hw);
+ memset(wl, 0, sizeof(*wl));
+ wl->hw = hw;
+ spin_lock_init(&wl->irq_lock);
+ spin_lock_init(&wl->leds_lock);
+ mutex_init(&wl->mutex);
+ INIT_LIST_HEAD(&wl->devlist);
+
+ ssb_set_devtypedata(dev, wl);
+ b43info(wl, "Broadcom %04X WLAN found\n", dev->bus->chip_id);
+ err = 0;
+ out:
+ return err;
+}
+
+static int b43_probe(struct ssb_device *dev, const struct ssb_device_id *id)
+{
+ struct b43_wl *wl;
+ int err;
+ int first = 0;
+
+ wl = ssb_get_devtypedata(dev);
+ if (!wl) {
+ /* Probing the first core. Must setup common struct b43_wl */
+ first = 1;
+ err = b43_wireless_init(dev);
+ if (err)
+ goto out;
+ wl = ssb_get_devtypedata(dev);
+ B43_WARN_ON(!wl);
+ }
+ err = b43_one_core_attach(dev, wl);
+ if (err)
+ goto err_wireless_exit;
+
+ if (first) {
+ err = ieee80211_register_hw(wl->hw);
+ if (err)
+ goto err_one_core_detach;
+ }
+
+ out:
+ return err;
+
+ err_one_core_detach:
+ b43_one_core_detach(dev);
+ err_wireless_exit:
+ if (first)
+ b43_wireless_exit(dev, wl);
+ return err;
+}
+
+static void b43_remove(struct ssb_device *dev)
+{
+ struct b43_wl *wl = ssb_get_devtypedata(dev);
+ struct b43_wldev *wldev = ssb_get_drvdata(dev);
+
+ B43_WARN_ON(!wl);
+ if (wl->current_dev == wldev)
+ ieee80211_unregister_hw(wl->hw);
+
+ b43_one_core_detach(dev);
+
+ if (list_empty(&wl->devlist)) {
+ /* Last core on the chip unregistered.
+ * We can destroy common struct b43_wl.
+ */
+ b43_wireless_exit(dev, wl);
+ }
+}
+
+/* Perform a hardware reset. This can be called from any context. */
+void b43_controller_restart(struct b43_wldev *dev, const char *reason)
+{
+ /* Must avoid requeueing, if we are in shutdown. */
+ if (b43_status(dev) < B43_STAT_INITIALIZED)
+ return;
+ b43info(dev->wl, "Controller RESET (%s) ...\n", reason);
+ queue_work(dev->wl->hw->workqueue, &dev->restart_work);
+}
+
+#ifdef CONFIG_PM
+
+static int b43_suspend(struct ssb_device *dev, pm_message_t state)
+{
+ struct b43_wldev *wldev = ssb_get_drvdata(dev);
+ struct b43_wl *wl = wldev->wl;
+
+ b43dbg(wl, "Suspending...\n");
+
+ mutex_lock(&wl->mutex);
+ wldev->suspend_init_status = b43_status(wldev);
+ if (wldev->suspend_init_status >= B43_STAT_STARTED)
+ b43_wireless_core_stop(wldev);
+ if (wldev->suspend_init_status >= B43_STAT_INITIALIZED)
+ b43_wireless_core_exit(wldev);
+ mutex_unlock(&wl->mutex);
+
+ b43dbg(wl, "Device suspended.\n");
+
+ return 0;
+}
+
+static int b43_resume(struct ssb_device *dev)
+{
+ struct b43_wldev *wldev = ssb_get_drvdata(dev);
+ struct b43_wl *wl = wldev->wl;
+ int err = 0;
+
+ b43dbg(wl, "Resuming...\n");
+
+ mutex_lock(&wl->mutex);
+ if (wldev->suspend_init_status >= B43_STAT_INITIALIZED) {
+ err = b43_wireless_core_init(wldev);
+ if (err) {
+ b43err(wl, "Resume failed at core init\n");
+ goto out;
+ }
+ }
+ if (wldev->suspend_init_status >= B43_STAT_STARTED) {
+ err = b43_wireless_core_start(wldev);
+ if (err) {
+ b43_wireless_core_exit(wldev);
+ b43err(wl, "Resume failed at core start\n");
+ goto out;
+ }
+ }
+ mutex_unlock(&wl->mutex);
+
+ b43dbg(wl, "Device resumed.\n");
+ out:
+ return err;
+}
+
+#else /* CONFIG_PM */
+# define b43_suspend NULL
+# define b43_resume NULL
+#endif /* CONFIG_PM */
+
+static struct ssb_driver b43_ssb_driver = {
+ .name = KBUILD_MODNAME,
+ .id_table = b43_ssb_tbl,
+ .probe = b43_probe,
+ .remove = b43_remove,
+ .suspend = b43_suspend,
+ .resume = b43_resume,
+};
+
+static int __init b43_init(void)
+{
+ int err;
+
+ b43_debugfs_init();
+ err = b43_pcmcia_init();
+ if (err)
+ goto err_dfs_exit;
+ err = ssb_driver_register(&b43_ssb_driver);
+ if (err)
+ goto err_pcmcia_exit;
+
+ return err;
+
+err_pcmcia_exit:
+ b43_pcmcia_exit();
+err_dfs_exit:
+ b43_debugfs_exit();
+ return err;
+}
+
+static void __exit b43_exit(void)
+{
+ ssb_driver_unregister(&b43_ssb_driver);
+ b43_pcmcia_exit();
+ b43_debugfs_exit();
+}
+
+module_init(b43_init)
+module_exit(b43_exit)
--- /dev/null
+/*
+
+ Broadcom B43 wireless driver
+
+ Copyright (c) 2005 Martin Langer <martin-langer@gmx.de>,
+ Stefano Brivio <st3@riseup.net>
+ Michael Buesch <mb@bu3sch.de>
+ Danny van Dyk <kugelfang@gentoo.org>
+ Andreas Jaggi <andreas.jaggi@waterwave.ch>
+
+ Some parts of the code in this file are derived from the ipw2200
+ driver Copyright(c) 2003 - 2004 Intel Corporation.
+
+ This program is free software; you can redistribute it and/or modify
+ it under the terms of the GNU General Public License as published by
+ the Free Software Foundation; either version 2 of the License, or
+ (at your option) any later version.
+
+ This program is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ GNU General Public License for more details.
+
+ You should have received a copy of the GNU General Public License
+ along with this program; see the file COPYING. If not, write to
+ the Free Software Foundation, Inc., 51 Franklin Steet, Fifth Floor,
+ Boston, MA 02110-1301, USA.
+
+*/
+
+#ifndef B43_MAIN_H_
+#define B43_MAIN_H_
+
+#include "b43.h"
+
+#define P4D_BYT3S(magic, nr_bytes) u8 __p4dding##magic[nr_bytes]
+#define P4D_BYTES(line, nr_bytes) P4D_BYT3S(line, nr_bytes)
+/* Magic helper macro to pad structures. Ignore those above. It's magic. */
+#define PAD_BYTES(nr_bytes) P4D_BYTES( __LINE__ , (nr_bytes))
+
+/* Lightweight function to convert a frequency (in Mhz) to a channel number. */
+static inline u8 b43_freq_to_channel_a(int freq)
+{
+ return ((freq - 5000) / 5);
+}
+static inline u8 b43_freq_to_channel_bg(int freq)
+{
+ u8 channel;
+
+ if (freq == 2484)
+ channel = 14;
+ else
+ channel = (freq - 2407) / 5;
+
+ return channel;
+}
+static inline u8 b43_freq_to_channel(struct b43_wldev *dev, int freq)
+{
+ if (dev->phy.type == B43_PHYTYPE_A)
+ return b43_freq_to_channel_a(freq);
+ return b43_freq_to_channel_bg(freq);
+}
+
+/* Lightweight function to convert a channel number to a frequency (in Mhz). */
+static inline int b43_channel_to_freq_a(u8 channel)
+{
+ return (5000 + (5 * channel));
+}
+static inline int b43_channel_to_freq_bg(u8 channel)
+{
+ int freq;
+
+ if (channel == 14)
+ freq = 2484;
+ else
+ freq = 2407 + (5 * channel);
+
+ return freq;
+}
+static inline int b43_channel_to_freq(struct b43_wldev *dev, u8 channel)
+{
+ if (dev->phy.type == B43_PHYTYPE_A)
+ return b43_channel_to_freq_a(channel);
+ return b43_channel_to_freq_bg(channel);
+}
+
+static inline int b43_is_cck_rate(int rate)
+{
+ return (rate == B43_CCK_RATE_1MB ||
+ rate == B43_CCK_RATE_2MB ||
+ rate == B43_CCK_RATE_5MB || rate == B43_CCK_RATE_11MB);
+}
+
+static inline int b43_is_ofdm_rate(int rate)
+{
+ return !b43_is_cck_rate(rate);
+}
+
+static inline int b43_is_hw_radio_enabled(struct b43_wldev *dev)
+{
+ /* function to return state of hardware enable of radio
+ * returns 0 if radio disabled, 1 if radio enabled
+ */
+ struct b43_phy *phy = &dev->phy;
+
+ if (phy->rev >= 3)
+ return ((b43_read32(dev, B43_MMIO_RADIO_HWENABLED_HI)
+ & B43_MMIO_RADIO_HWENABLED_HI_MASK)
+ == 0) ? 1 : 0;
+ else
+ return ((b43_read16(dev, B43_MMIO_RADIO_HWENABLED_LO)
+ & B43_MMIO_RADIO_HWENABLED_LO_MASK)
+ == 0) ? 0 : 1;
+}
+
+void b43_tsf_read(struct b43_wldev *dev, u64 * tsf);
+void b43_tsf_write(struct b43_wldev *dev, u64 tsf);
+
+u32 b43_shm_read32(struct b43_wldev *dev, u16 routing, u16 offset);
+u16 b43_shm_read16(struct b43_wldev *dev, u16 routing, u16 offset);
+void b43_shm_write32(struct b43_wldev *dev, u16 routing, u16 offset, u32 value);
+void b43_shm_write16(struct b43_wldev *dev, u16 routing, u16 offset, u16 value);
+
+u32 b43_hf_read(struct b43_wldev *dev);
+void b43_hf_write(struct b43_wldev *dev, u32 value);
+
+void b43_dummy_transmission(struct b43_wldev *dev);
+
+void b43_wireless_core_reset(struct b43_wldev *dev, u32 flags);
+
+void b43_mac_suspend(struct b43_wldev *dev);
+void b43_mac_enable(struct b43_wldev *dev);
+
+void b43_controller_restart(struct b43_wldev *dev, const char *reason);
+
+#define B43_PS_ENABLED (1 << 0) /* Force enable hardware power saving */
+#define B43_PS_DISABLED (1 << 1) /* Force disable hardware power saving */
+#define B43_PS_AWAKE (1 << 2) /* Force device awake */
+#define B43_PS_ASLEEP (1 << 3) /* Force device asleep */
+void b43_power_saving_ctl_bits(struct b43_wldev *dev, unsigned int ps_flags);
+
+#endif /* B43_MAIN_H_ */
--- /dev/null
+/*
+
+ Broadcom B43 wireless driver
+
+ Copyright (c) 2007 Michael Buesch <mb@bu3sch.de>
+
+ This program is free software; you can redistribute it and/or modify
+ it under the terms of the GNU General Public License as published by
+ the Free Software Foundation; either version 2 of the License, or
+ (at your option) any later version.
+
+ This program is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ GNU General Public License for more details.
+
+ You should have received a copy of the GNU General Public License
+ along with this program; see the file COPYING. If not, write to
+ the Free Software Foundation, Inc., 51 Franklin Steet, Fifth Floor,
+ Boston, MA 02110-1301, USA.
+
+*/
+
+#include <linux/ssb/ssb.h>
+
+#include <pcmcia/cs_types.h>
+#include <pcmcia/cs.h>
+#include <pcmcia/cistpl.h>
+#include <pcmcia/ciscode.h>
+#include <pcmcia/ds.h>
+#include <pcmcia/cisreg.h>
+
+static /*const */ struct pcmcia_device_id b43_pcmcia_tbl[] = {
+ PCMCIA_DEVICE_MANF_CARD(0x2D0, 0x448),
+ PCMCIA_DEVICE_NULL,
+};
+
+MODULE_DEVICE_TABLE(pcmcia, b43_pcmcia_tbl);
+
+#ifdef CONFIG_PM
+static int b43_pcmcia_suspend(struct pcmcia_device *dev)
+{
+ //TODO
+ return 0;
+}
+
+static int b43_pcmcia_resume(struct pcmcia_device *dev)
+{
+ //TODO
+ return 0;
+}
+#else /* CONFIG_PM */
+# define b43_pcmcia_suspend NULL
+# define b43_pcmcia_resume NULL
+#endif /* CONFIG_PM */
+
+static int __devinit b43_pcmcia_probe(struct pcmcia_device *dev)
+{
+ struct ssb_bus *ssb;
+ win_req_t win;
+ memreq_t mem;
+ tuple_t tuple;
+ cisparse_t parse;
+ int err = -ENOMEM;
+ int res;
+ unsigned char buf[64];
+
+ ssb = kzalloc(sizeof(*ssb), GFP_KERNEL);
+ if (!ssb)
+ goto out;
+
+ err = -ENODEV;
+ tuple.DesiredTuple = CISTPL_CONFIG;
+ tuple.Attributes = 0;
+ tuple.TupleData = buf;
+ tuple.TupleDataMax = sizeof(buf);
+ tuple.TupleOffset = 0;
+
+ res = pcmcia_get_first_tuple(dev, &tuple);
+ if (res != CS_SUCCESS)
+ goto err_kfree_ssb;
+ res = pcmcia_get_tuple_data(dev, &tuple);
+ if (res != CS_SUCCESS)
+ goto err_kfree_ssb;
+ res = pcmcia_parse_tuple(dev, &tuple, &parse);
+ if (res != CS_SUCCESS)
+ goto err_kfree_ssb;
+
+ dev->conf.ConfigBase = parse.config.base;
+ dev->conf.Present = parse.config.rmask[0];
+
+ dev->io.BasePort2 = 0;
+ dev->io.NumPorts2 = 0;
+ dev->io.Attributes2 = 0;
+
+ win.Attributes = WIN_MEMORY_TYPE_CM | WIN_ENABLE | WIN_USE_WAIT;
+ win.Base = 0;
+ win.Size = SSB_CORE_SIZE;
+ win.AccessSpeed = 1000;
+ res = pcmcia_request_window(&dev, &win, &dev->win);
+ if (res != CS_SUCCESS)
+ goto err_kfree_ssb;
+
+ mem.CardOffset = 0;
+ mem.Page = 0;
+ res = pcmcia_map_mem_page(dev->win, &mem);
+ if (res != CS_SUCCESS)
+ goto err_kfree_ssb;
+
+ res = pcmcia_request_configuration(dev, &dev->conf);
+ if (res != CS_SUCCESS)
+ goto err_disable;
+
+ err = ssb_bus_pcmciabus_register(ssb, dev, win.Base);
+ dev->priv = ssb;
+
+ out:
+ return err;
+ err_disable:
+ pcmcia_disable_device(dev);
+ err_kfree_ssb:
+ kfree(ssb);
+ return err;
+}
+
+static void __devexit b43_pcmcia_remove(struct pcmcia_device *dev)
+{
+ struct ssb_bus *ssb = dev->priv;
+
+ ssb_bus_unregister(ssb);
+ pcmcia_release_window(dev->win);
+ pcmcia_disable_device(dev);
+ kfree(ssb);
+ dev->priv = NULL;
+}
+
+static struct pcmcia_driver b43_pcmcia_driver = {
+ .owner = THIS_MODULE,
+ .drv = {
+ .name = "b43-pcmcia",
+ },
+ .id_table = b43_pcmcia_tbl,
+ .probe = b43_pcmcia_probe,
+ .remove = b43_pcmcia_remove,
+ .suspend = b43_pcmcia_suspend,
+ .resume = b43_pcmcia_resume,
+};
+
+int b43_pcmcia_init(void)
+{
+ return pcmcia_register_driver(&b43_pcmcia_driver);
+}
+
+void b43_pcmcia_exit(void)
+{
+ pcmcia_unregister_driver(&b43_pcmcia_driver);
+}
--- /dev/null
+#ifndef B43_PCMCIA_H_
+#define B43_PCMCIA_H_
+
+#ifdef CONFIG_B43_PCMCIA
+
+int b43_pcmcia_init(void);
+void b43_pcmcia_exit(void);
+
+#else /* CONFIG_B43_PCMCIA */
+
+static inline int b43_pcmcia_init(void)
+{
+ return 0;
+}
+static inline void b43_pcmcia_exit(void)
+{
+}
+
+#endif /* CONFIG_B43_PCMCIA */
+#endif /* B43_PCMCIA_H_ */
--- /dev/null
+/*
+
+ Broadcom B43 wireless driver
+
+ Copyright (c) 2005 Martin Langer <martin-langer@gmx.de>,
+ Copyright (c) 2005, 2006 Stefano Brivio <st3@riseup.net>
+ Copyright (c) 2005, 2006 Michael Buesch <mb@bu3sch.de>
+ Copyright (c) 2005, 2006 Danny van Dyk <kugelfang@gentoo.org>
+ Copyright (c) 2005, 2006 Andreas Jaggi <andreas.jaggi@waterwave.ch>
+
+ This program is free software; you can redistribute it and/or modify
+ it under the terms of the GNU General Public License as published by
+ the Free Software Foundation; either version 2 of the License, or
+ (at your option) any later version.
+
+ This program is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ GNU General Public License for more details.
+
+ You should have received a copy of the GNU General Public License
+ along with this program; see the file COPYING. If not, write to
+ the Free Software Foundation, Inc., 51 Franklin Steet, Fifth Floor,
+ Boston, MA 02110-1301, USA.
+
+*/
+
+#include <linux/delay.h>
+#include <linux/types.h>
+
+#include "b43.h"
+#include "phy.h"
+#include "main.h"
+#include "tables.h"
+#include "lo.h"
+
+static const s8 b43_tssi2dbm_b_table[] = {
+ 0x4D, 0x4C, 0x4B, 0x4A,
+ 0x4A, 0x49, 0x48, 0x47,
+ 0x47, 0x46, 0x45, 0x45,
+ 0x44, 0x43, 0x42, 0x42,
+ 0x41, 0x40, 0x3F, 0x3E,
+ 0x3D, 0x3C, 0x3B, 0x3A,
+ 0x39, 0x38, 0x37, 0x36,
+ 0x35, 0x34, 0x32, 0x31,
+ 0x30, 0x2F, 0x2D, 0x2C,
+ 0x2B, 0x29, 0x28, 0x26,
+ 0x25, 0x23, 0x21, 0x1F,
+ 0x1D, 0x1A, 0x17, 0x14,
+ 0x10, 0x0C, 0x06, 0x00,
+ -7, -7, -7, -7,
+ -7, -7, -7, -7,
+ -7, -7, -7, -7,
+};
+
+static const s8 b43_tssi2dbm_g_table[] = {
+ 77, 77, 77, 76,
+ 76, 76, 75, 75,
+ 74, 74, 73, 73,
+ 73, 72, 72, 71,
+ 71, 70, 70, 69,
+ 68, 68, 67, 67,
+ 66, 65, 65, 64,
+ 63, 63, 62, 61,
+ 60, 59, 58, 57,
+ 56, 55, 54, 53,
+ 52, 50, 49, 47,
+ 45, 43, 40, 37,
+ 33, 28, 22, 14,
+ 5, -7, -20, -20,
+ -20, -20, -20, -20,
+ -20, -20, -20, -20,
+};
+
+const u8 b43_radio_channel_codes_bg[] = {
+ 12, 17, 22, 27,
+ 32, 37, 42, 47,
+ 52, 57, 62, 67,
+ 72, 84,
+};
+
+static void b43_phy_initg(struct b43_wldev *dev);
+
+/* Reverse the bits of a 4bit value.
+ * Example: 1101 is flipped 1011
+ */
+static u16 flip_4bit(u16 value)
+{
+ u16 flipped = 0x0000;
+
+ B43_WARN_ON(value & ~0x000F);
+
+ flipped |= (value & 0x0001) << 3;
+ flipped |= (value & 0x0002) << 1;
+ flipped |= (value & 0x0004) >> 1;
+ flipped |= (value & 0x0008) >> 3;
+
+ return flipped;
+}
+
+static void generate_rfatt_list(struct b43_wldev *dev,
+ struct b43_rfatt_list *list)
+{
+ struct b43_phy *phy = &dev->phy;
+
+ /* APHY.rev < 5 || GPHY.rev < 6 */
+ static const struct b43_rfatt rfatt_0[] = {
+ {.att = 3,.with_padmix = 0,},
+ {.att = 1,.with_padmix = 0,},
+ {.att = 5,.with_padmix = 0,},
+ {.att = 7,.with_padmix = 0,},
+ {.att = 9,.with_padmix = 0,},
+ {.att = 2,.with_padmix = 0,},
+ {.att = 0,.with_padmix = 0,},
+ {.att = 4,.with_padmix = 0,},
+ {.att = 6,.with_padmix = 0,},
+ {.att = 8,.with_padmix = 0,},
+ {.att = 1,.with_padmix = 1,},
+ {.att = 2,.with_padmix = 1,},
+ {.att = 3,.with_padmix = 1,},
+ {.att = 4,.with_padmix = 1,},
+ };
+ /* Radio.rev == 8 && Radio.version == 0x2050 */
+ static const struct b43_rfatt rfatt_1[] = {
+ {.att = 2,.with_padmix = 1,},
+ {.att = 4,.with_padmix = 1,},
+ {.att = 6,.with_padmix = 1,},
+ {.att = 8,.with_padmix = 1,},
+ {.att = 10,.with_padmix = 1,},
+ {.att = 12,.with_padmix = 1,},
+ {.att = 14,.with_padmix = 1,},
+ };
+ /* Otherwise */
+ static const struct b43_rfatt rfatt_2[] = {
+ {.att = 0,.with_padmix = 1,},
+ {.att = 2,.with_padmix = 1,},
+ {.att = 4,.with_padmix = 1,},
+ {.att = 6,.with_padmix = 1,},
+ {.att = 8,.with_padmix = 1,},
+ {.att = 9,.with_padmix = 1,},
+ {.att = 9,.with_padmix = 1,},
+ };
+
+ if ((phy->type == B43_PHYTYPE_A && phy->rev < 5) ||
+ (phy->type == B43_PHYTYPE_G && phy->rev < 6)) {
+ /* Software pctl */
+ list->list = rfatt_0;
+ list->len = ARRAY_SIZE(rfatt_0);
+ list->min_val = 0;
+ list->max_val = 9;
+ return;
+ }
+ if (phy->radio_ver == 0x2050 && phy->radio_rev == 8) {
+ /* Hardware pctl */
+ list->list = rfatt_1;
+ list->len = ARRAY_SIZE(rfatt_1);
+ list->min_val = 2;
+ list->max_val = 14;
+ return;
+ }
+ /* Hardware pctl */
+ list->list = rfatt_2;
+ list->len = ARRAY_SIZE(rfatt_2);
+ list->min_val = 0;
+ list->max_val = 9;
+}
+
+static void generate_bbatt_list(struct b43_wldev *dev,
+ struct b43_bbatt_list *list)
+{
+ static const struct b43_bbatt bbatt_0[] = {
+ {.att = 0,},
+ {.att = 1,},
+ {.att = 2,},
+ {.att = 3,},
+ {.att = 4,},
+ {.att = 5,},
+ {.att = 6,},
+ {.att = 7,},
+ {.att = 8,},
+ };
+
+ list->list = bbatt_0;
+ list->len = ARRAY_SIZE(bbatt_0);
+ list->min_val = 0;
+ list->max_val = 8;
+}
+
+bool b43_has_hardware_pctl(struct b43_phy *phy)
+{
+ if (!phy->hardware_power_control)
+ return 0;
+ switch (phy->type) {
+ case B43_PHYTYPE_A:
+ if (phy->rev >= 5)
+ return 1;
+ break;
+ case B43_PHYTYPE_G:
+ if (phy->rev >= 6)
+ return 1;
+ break;
+ default:
+ B43_WARN_ON(1);
+ }
+ return 0;
+}
+
+static void b43_shm_clear_tssi(struct b43_wldev *dev)
+{
+ struct b43_phy *phy = &dev->phy;
+
+ switch (phy->type) {
+ case B43_PHYTYPE_A:
+ b43_shm_write16(dev, B43_SHM_SHARED, 0x0068, 0x7F7F);
+ b43_shm_write16(dev, B43_SHM_SHARED, 0x006a, 0x7F7F);
+ break;
+ case B43_PHYTYPE_B:
+ case B43_PHYTYPE_G:
+ b43_shm_write16(dev, B43_SHM_SHARED, 0x0058, 0x7F7F);
+ b43_shm_write16(dev, B43_SHM_SHARED, 0x005a, 0x7F7F);
+ b43_shm_write16(dev, B43_SHM_SHARED, 0x0070, 0x7F7F);
+ b43_shm_write16(dev, B43_SHM_SHARED, 0x0072, 0x7F7F);
+ break;
+ }
+}
+
+void b43_raw_phy_lock(struct b43_wldev *dev)
+{
+ struct b43_phy *phy = &dev->phy;
+
+ B43_WARN_ON(!irqs_disabled());
+
+ /* We had a check for MACCTL==0 here, but I think that doesn't
+ * make sense, as MACCTL is never 0 when this is called.
+ * --mb */
+ B43_WARN_ON(b43_read32(dev, B43_MMIO_MACCTL) == 0);
+
+ if (dev->dev->id.revision < 3) {
+ b43_mac_suspend(dev);
+ spin_lock(&phy->lock);
+ } else {
+ if (!b43_is_mode(dev->wl, IEEE80211_IF_TYPE_AP))
+ b43_power_saving_ctl_bits(dev, B43_PS_AWAKE);
+ }
+ phy->locked = 1;
+}
+
+void b43_raw_phy_unlock(struct b43_wldev *dev)
+{
+ struct b43_phy *phy = &dev->phy;
+
+ B43_WARN_ON(!irqs_disabled());
+ if (dev->dev->id.revision < 3) {
+ if (phy->locked) {
+ spin_unlock(&phy->lock);
+ b43_mac_enable(dev);
+ }
+ } else {
+ if (!b43_is_mode(dev->wl, IEEE80211_IF_TYPE_AP))
+ b43_power_saving_ctl_bits(dev, 0);
+ }
+ phy->locked = 0;
+}
+
+/* Different PHYs require different register routing flags.
+ * This adjusts (and does sanity checks on) the routing flags.
+ */
+static inline u16 adjust_phyreg_for_phytype(struct b43_phy *phy,
+ u16 offset, struct b43_wldev *dev)
+{
+ if (phy->type == B43_PHYTYPE_A) {
+ /* OFDM registers are base-registers for the A-PHY. */
+ offset &= ~B43_PHYROUTE_OFDM_GPHY;
+ }
+ if (offset & B43_PHYROUTE_EXT_GPHY) {
+ /* Ext-G registers are only available on G-PHYs */
+ if (phy->type != B43_PHYTYPE_G) {
+ b43dbg(dev->wl, "EXT-G PHY access at "
+ "0x%04X on %u type PHY\n", offset, phy->type);
+ }
+ }
+
+ return offset;
+}
+
+u16 b43_phy_read(struct b43_wldev * dev, u16 offset)
+{
+ struct b43_phy *phy = &dev->phy;
+
+ offset = adjust_phyreg_for_phytype(phy, offset, dev);
+ b43_write16(dev, B43_MMIO_PHY_CONTROL, offset);
+ return b43_read16(dev, B43_MMIO_PHY_DATA);
+}
+
+void b43_phy_write(struct b43_wldev *dev, u16 offset, u16 val)
+{
+ struct b43_phy *phy = &dev->phy;
+
+ offset = adjust_phyreg_for_phytype(phy, offset, dev);
+ b43_write16(dev, B43_MMIO_PHY_CONTROL, offset);
+ mmiowb();
+ b43_write16(dev, B43_MMIO_PHY_DATA, val);
+}
+
+static void b43_radio_set_txpower_a(struct b43_wldev *dev, u16 txpower);
+
+/* Adjust the transmission power output (G-PHY) */
+void b43_set_txpower_g(struct b43_wldev *dev,
+ const struct b43_bbatt *bbatt,
+ const struct b43_rfatt *rfatt, u8 tx_control)
+{
+ struct b43_phy *phy = &dev->phy;
+ struct b43_txpower_lo_control *lo = phy->lo_control;
+ u16 bb, rf;
+ u16 tx_bias, tx_magn;
+
+ bb = bbatt->att;
+ rf = rfatt->att;
+ tx_bias = lo->tx_bias;
+ tx_magn = lo->tx_magn;
+ if (unlikely(tx_bias == 0xFF))
+ tx_bias = 0;
+
+ /* Save the values for later */
+ phy->tx_control = tx_control;
+ memcpy(&phy->rfatt, rfatt, sizeof(*rfatt));
+ memcpy(&phy->bbatt, bbatt, sizeof(*bbatt));
+
+ if (b43_debug(dev, B43_DBG_XMITPOWER)) {
+ b43dbg(dev->wl, "Tuning TX-power to bbatt(%u), "
+ "rfatt(%u), tx_control(0x%02X), "
+ "tx_bias(0x%02X), tx_magn(0x%02X)\n",
+ bb, rf, tx_control, tx_bias, tx_magn);
+ }
+
+ b43_phy_set_baseband_attenuation(dev, bb);
+ b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_RFATT, rf);
+ if (phy->radio_ver == 0x2050 && phy->radio_rev == 8) {
+ b43_radio_write16(dev, 0x43,
+ (rf & 0x000F) | (tx_control & 0x0070));
+ } else {
+ b43_radio_write16(dev, 0x43, (b43_radio_read16(dev, 0x43)
+ & 0xFFF0) | (rf & 0x000F));
+ b43_radio_write16(dev, 0x52, (b43_radio_read16(dev, 0x52)
+ & ~0x0070) | (tx_control &
+ 0x0070));
+ }
+ if (has_tx_magnification(phy)) {
+ b43_radio_write16(dev, 0x52, tx_magn | tx_bias);
+ } else {
+ b43_radio_write16(dev, 0x52, (b43_radio_read16(dev, 0x52)
+ & 0xFFF0) | (tx_bias & 0x000F));
+ }
+ if (phy->type == B43_PHYTYPE_G)
+ b43_lo_g_adjust(dev);
+}
+
+static void default_baseband_attenuation(struct b43_wldev *dev,
+ struct b43_bbatt *bb)
+{
+ struct b43_phy *phy = &dev->phy;
+
+ if (phy->radio_ver == 0x2050 && phy->radio_rev < 6)
+ bb->att = 0;
+ else
+ bb->att = 2;
+}
+
+static void default_radio_attenuation(struct b43_wldev *dev,
+ struct b43_rfatt *rf)
+{
+ struct ssb_bus *bus = dev->dev->bus;
+ struct b43_phy *phy = &dev->phy;
+
+ rf->with_padmix = 0;
+
+ if (bus->boardinfo.vendor == SSB_BOARDVENDOR_BCM &&
+ bus->boardinfo.type == SSB_BOARD_BCM4309G) {
+ if (bus->boardinfo.rev < 0x43) {
+ rf->att = 2;
+ return;
+ } else if (bus->boardinfo.rev < 0x51) {
+ rf->att = 3;
+ return;
+ }
+ }
+
+ if (phy->type == B43_PHYTYPE_A) {
+ rf->att = 0x60;
+ return;
+ }
+
+ switch (phy->radio_ver) {
+ case 0x2053:
+ switch (phy->radio_rev) {
+ case 1:
+ rf->att = 6;
+ return;
+ }
+ break;
+ case 0x2050:
+ switch (phy->radio_rev) {
+ case 0:
+ rf->att = 5;
+ return;
+ case 1:
+ if (phy->type == B43_PHYTYPE_G) {
+ if (bus->boardinfo.vendor == SSB_BOARDVENDOR_BCM
+ && bus->boardinfo.type == SSB_BOARD_BCM4309G
+ && bus->boardinfo.rev >= 30)
+ rf->att = 3;
+ else if (bus->boardinfo.vendor ==
+ SSB_BOARDVENDOR_BCM
+ && bus->boardinfo.type ==
+ SSB_BOARD_BU4306)
+ rf->att = 3;
+ else
+ rf->att = 1;
+ } else {
+ if (bus->boardinfo.vendor == SSB_BOARDVENDOR_BCM
+ && bus->boardinfo.type == SSB_BOARD_BCM4309G
+ && bus->boardinfo.rev >= 30)
+ rf->att = 7;
+ else
+ rf->att = 6;
+ }
+ return;
+ case 2:
+ if (phy->type == B43_PHYTYPE_G) {
+ if (bus->boardinfo.vendor == SSB_BOARDVENDOR_BCM
+ && bus->boardinfo.type == SSB_BOARD_BCM4309G
+ && bus->boardinfo.rev >= 30)
+ rf->att = 3;
+ else if (bus->boardinfo.vendor ==
+ SSB_BOARDVENDOR_BCM
+ && bus->boardinfo.type ==
+ SSB_BOARD_BU4306)
+ rf->att = 5;
+ else if (bus->chip_id == 0x4320)
+ rf->att = 4;
+ else
+ rf->att = 3;
+ } else
+ rf->att = 6;
+ return;
+ case 3:
+ rf->att = 5;
+ return;
+ case 4:
+ case 5:
+ rf->att = 1;
+ return;
+ case 6:
+ case 7:
+ rf->att = 5;
+ return;
+ case 8:
+ rf->att = 0xA;
+ rf->with_padmix = 1;
+ return;
+ case 9:
+ default:
+ rf->att = 5;
+ return;
+ }
+ }
+ rf->att = 5;
+}
+
+static u16 default_tx_control(struct b43_wldev *dev)
+{
+ struct b43_phy *phy = &dev->phy;
+
+ if (phy->radio_ver != 0x2050)
+ return 0;
+ if (phy->radio_rev == 1)
+ return B43_TXCTL_PA2DB | B43_TXCTL_TXMIX;
+ if (phy->radio_rev < 6)
+ return B43_TXCTL_PA2DB;
+ if (phy->radio_rev == 8)
+ return B43_TXCTL_TXMIX;
+ return 0;
+}
+
+/* This func is called "PHY calibrate" in the specs... */
+void b43_phy_early_init(struct b43_wldev *dev)
+{
+ struct b43_phy *phy = &dev->phy;
+ struct b43_txpower_lo_control *lo = phy->lo_control;
+
+ default_baseband_attenuation(dev, &phy->bbatt);
+ default_radio_attenuation(dev, &phy->rfatt);
+ phy->tx_control = (default_tx_control(dev) << 4);
+
+ /* Commit previous writes */
+ b43_read32(dev, B43_MMIO_MACCTL);
+
+ if (phy->type == B43_PHYTYPE_B || phy->type == B43_PHYTYPE_G) {
+ generate_rfatt_list(dev, &lo->rfatt_list);
+ generate_bbatt_list(dev, &lo->bbatt_list);
+ }
+ if (phy->type == B43_PHYTYPE_G && phy->rev == 1) {
+ /* Workaround: Temporarly disable gmode through the early init
+ * phase, as the gmode stuff is not needed for phy rev 1 */
+ phy->gmode = 0;
+ b43_wireless_core_reset(dev, 0);
+ b43_phy_initg(dev);
+ phy->gmode = 1;
+ b43_wireless_core_reset(dev, B43_TMSLOW_GMODE);
+ }
+}
+
+/* GPHY_TSSI_Power_Lookup_Table_Init */
+static void b43_gphy_tssi_power_lt_init(struct b43_wldev *dev)
+{
+ struct b43_phy *phy = &dev->phy;
+ int i;
+ u16 value;
+
+ for (i = 0; i < 32; i++)
+ b43_ofdmtab_write16(dev, 0x3C20, i, phy->tssi2dbm[i]);
+ for (i = 32; i < 64; i++)
+ b43_ofdmtab_write16(dev, 0x3C00, i - 32, phy->tssi2dbm[i]);
+ for (i = 0; i < 64; i += 2) {
+ value = (u16) phy->tssi2dbm[i];
+ value |= ((u16) phy->tssi2dbm[i + 1]) << 8;
+ b43_phy_write(dev, 0x380 + (i / 2), value);
+ }
+}
+
+/* GPHY_Gain_Lookup_Table_Init */
+static void b43_gphy_gain_lt_init(struct b43_wldev *dev)
+{
+ struct b43_phy *phy = &dev->phy;
+ struct b43_txpower_lo_control *lo = phy->lo_control;
+ u16 nr_written = 0;
+ u16 tmp;
+ u8 rf, bb;
+
+ if (!lo->lo_measured) {
+ b43_phy_write(dev, 0x3FF, 0);
+ return;
+ }
+
+ for (rf = 0; rf < lo->rfatt_list.len; rf++) {
+ for (bb = 0; bb < lo->bbatt_list.len; bb++) {
+ if (nr_written >= 0x40)
+ return;
+ tmp = lo->bbatt_list.list[bb].att;
+ tmp <<= 8;
+ if (phy->radio_rev == 8)
+ tmp |= 0x50;
+ else
+ tmp |= 0x40;
+ tmp |= lo->rfatt_list.list[rf].att;
+ b43_phy_write(dev, 0x3C0 + nr_written, tmp);
+ nr_written++;
+ }
+ }
+}
+
+/* GPHY_DC_Lookup_Table */
+void b43_gphy_dc_lt_init(struct b43_wldev *dev)
+{
+ struct b43_phy *phy = &dev->phy;
+ struct b43_txpower_lo_control *lo = phy->lo_control;
+ struct b43_loctl *loctl0;
+ struct b43_loctl *loctl1;
+ int i;
+ int rf_offset, bb_offset;
+ u16 tmp;
+
+ for (i = 0; i < lo->rfatt_list.len + lo->bbatt_list.len; i += 2) {
+ rf_offset = i / lo->rfatt_list.len;
+ bb_offset = i % lo->rfatt_list.len;
+
+ loctl0 = b43_get_lo_g_ctl(dev, &lo->rfatt_list.list[rf_offset],
+ &lo->bbatt_list.list[bb_offset]);
+ if (i + 1 < lo->rfatt_list.len * lo->bbatt_list.len) {
+ rf_offset = (i + 1) / lo->rfatt_list.len;
+ bb_offset = (i + 1) % lo->rfatt_list.len;
+
+ loctl1 =
+ b43_get_lo_g_ctl(dev,
+ &lo->rfatt_list.list[rf_offset],
+ &lo->bbatt_list.list[bb_offset]);
+ } else
+ loctl1 = loctl0;
+
+ tmp = ((u16) loctl0->q & 0xF);
+ tmp |= ((u16) loctl0->i & 0xF) << 4;
+ tmp |= ((u16) loctl1->q & 0xF) << 8;
+ tmp |= ((u16) loctl1->i & 0xF) << 12; //FIXME?
+ b43_phy_write(dev, 0x3A0 + (i / 2), tmp);
+ }
+}
+
+static void hardware_pctl_init_aphy(struct b43_wldev *dev)
+{
+ //TODO
+}
+
+static void hardware_pctl_init_gphy(struct b43_wldev *dev)
+{
+ struct b43_phy *phy = &dev->phy;
+
+ b43_phy_write(dev, 0x0036, (b43_phy_read(dev, 0x0036) & 0xFFC0)
+ | (phy->tgt_idle_tssi - phy->cur_idle_tssi));
+ b43_phy_write(dev, 0x0478, (b43_phy_read(dev, 0x0478) & 0xFF00)
+ | (phy->tgt_idle_tssi - phy->cur_idle_tssi));
+ b43_gphy_tssi_power_lt_init(dev);
+ b43_gphy_gain_lt_init(dev);
+ b43_phy_write(dev, 0x0060, b43_phy_read(dev, 0x0060) & 0xFFBF);
+ b43_phy_write(dev, 0x0014, 0x0000);
+
+ B43_WARN_ON(phy->rev < 6);
+ b43_phy_write(dev, 0x0478, b43_phy_read(dev, 0x0478)
+ | 0x0800);
+ b43_phy_write(dev, 0x0478, b43_phy_read(dev, 0x0478)
+ & 0xFEFF);
+ b43_phy_write(dev, 0x0801, b43_phy_read(dev, 0x0801)
+ & 0xFFBF);
+
+ b43_gphy_dc_lt_init(dev);
+}
+
+/* HardwarePowerControl init for A and G PHY */
+static void b43_hardware_pctl_init(struct b43_wldev *dev)
+{
+ struct b43_phy *phy = &dev->phy;
+
+ if (!b43_has_hardware_pctl(phy)) {
+ /* No hardware power control */
+ b43_hf_write(dev, b43_hf_read(dev) & ~B43_HF_HWPCTL);
+ return;
+ }
+ /* Init the hwpctl related hardware */
+ switch (phy->type) {
+ case B43_PHYTYPE_A:
+ hardware_pctl_init_aphy(dev);
+ break;
+ case B43_PHYTYPE_G:
+ hardware_pctl_init_gphy(dev);
+ break;
+ default:
+ B43_WARN_ON(1);
+ }
+ /* Enable hardware pctl in firmware. */
+ b43_hf_write(dev, b43_hf_read(dev) | B43_HF_HWPCTL);
+}
+
+static void b43_hardware_pctl_early_init(struct b43_wldev *dev)
+{
+ struct b43_phy *phy = &dev->phy;
+
+ if (!b43_has_hardware_pctl(phy)) {
+ b43_phy_write(dev, 0x047A, 0xC111);
+ return;
+ }
+
+ b43_phy_write(dev, 0x0036, b43_phy_read(dev, 0x0036) & 0xFEFF);
+ b43_phy_write(dev, 0x002F, 0x0202);
+ b43_phy_write(dev, 0x047C, b43_phy_read(dev, 0x047C) | 0x0002);
+ b43_phy_write(dev, 0x047A, b43_phy_read(dev, 0x047A) | 0xF000);
+ if (phy->radio_ver == 0x2050 && phy->radio_rev == 8) {
+ b43_phy_write(dev, 0x047A, (b43_phy_read(dev, 0x047A)
+ & 0xFF0F) | 0x0010);
+ b43_phy_write(dev, 0x005D, b43_phy_read(dev, 0x005D)
+ | 0x8000);
+ b43_phy_write(dev, 0x004E, (b43_phy_read(dev, 0x004E)
+ & 0xFFC0) | 0x0010);
+ b43_phy_write(dev, 0x002E, 0xC07F);
+ b43_phy_write(dev, 0x0036, b43_phy_read(dev, 0x0036)
+ | 0x0400);
+ } else {
+ b43_phy_write(dev, 0x0036, b43_phy_read(dev, 0x0036)
+ | 0x0200);
+ b43_phy_write(dev, 0x0036, b43_phy_read(dev, 0x0036)
+ | 0x0400);
+ b43_phy_write(dev, 0x005D, b43_phy_read(dev, 0x005D)
+ & 0x7FFF);
+ b43_phy_write(dev, 0x004F, b43_phy_read(dev, 0x004F)
+ & 0xFFFE);
+ b43_phy_write(dev, 0x004E, (b43_phy_read(dev, 0x004E)
+ & 0xFFC0) | 0x0010);
+ b43_phy_write(dev, 0x002E, 0xC07F);
+ b43_phy_write(dev, 0x047A, (b43_phy_read(dev, 0x047A)
+ & 0xFF0F) | 0x0010);
+ }
+}
+
+/* Intialize B/G PHY power control
+ * as described in http://bcm-specs.sipsolutions.net/InitPowerControl
+ */
+static void b43_phy_init_pctl(struct b43_wldev *dev)
+{
+ struct ssb_bus *bus = dev->dev->bus;
+ struct b43_phy *phy = &dev->phy;
+ struct b43_rfatt old_rfatt;
+ struct b43_bbatt old_bbatt;
+ u8 old_tx_control = 0;
+
+ if ((bus->boardinfo.vendor == SSB_BOARDVENDOR_BCM) &&
+ (bus->boardinfo.type == SSB_BOARD_BU4306))
+ return;
+
+ b43_phy_write(dev, 0x0028, 0x8018);
+
+ /* This does something with the Analog... */
+ b43_write16(dev, B43_MMIO_PHY0, b43_read16(dev, B43_MMIO_PHY0)
+ & 0xFFDF);
+
+ if (phy->type == B43_PHYTYPE_G && !phy->gmode)
+ return;
+ b43_hardware_pctl_early_init(dev);
+ if (phy->cur_idle_tssi == 0) {
+ if (phy->radio_ver == 0x2050 && phy->analog == 0) {
+ b43_radio_write16(dev, 0x0076,
+ (b43_radio_read16(dev, 0x0076)
+ & 0x00F7) | 0x0084);
+ } else {
+ struct b43_rfatt rfatt;
+ struct b43_bbatt bbatt;
+
+ memcpy(&old_rfatt, &phy->rfatt, sizeof(old_rfatt));
+ memcpy(&old_bbatt, &phy->bbatt, sizeof(old_bbatt));
+ old_tx_control = phy->tx_control;
+
+ bbatt.att = 11;
+ if (phy->radio_rev == 8) {
+ rfatt.att = 15;
+ rfatt.with_padmix = 1;
+ } else {
+ rfatt.att = 9;
+ rfatt.with_padmix = 0;
+ }
+ b43_set_txpower_g(dev, &bbatt, &rfatt, 0);
+ }
+ b43_dummy_transmission(dev);
+ phy->cur_idle_tssi = b43_phy_read(dev, B43_PHY_ITSSI);
+ if (B43_DEBUG) {
+ /* Current-Idle-TSSI sanity check. */
+ if (abs(phy->cur_idle_tssi - phy->tgt_idle_tssi) >= 20) {
+ b43dbg(dev->wl,
+ "!WARNING! Idle-TSSI phy->cur_idle_tssi "
+ "measuring failed. (cur=%d, tgt=%d). Disabling TX power "
+ "adjustment.\n", phy->cur_idle_tssi,
+ phy->tgt_idle_tssi);
+ phy->cur_idle_tssi = 0;
+ }
+ }
+ if (phy->radio_ver == 0x2050 && phy->analog == 0) {
+ b43_radio_write16(dev, 0x0076,
+ b43_radio_read16(dev, 0x0076)
+ & 0xFF7B);
+ } else {
+ b43_set_txpower_g(dev, &old_bbatt,
+ &old_rfatt, old_tx_control);
+ }
+ }
+ b43_hardware_pctl_init(dev);
+ b43_shm_clear_tssi(dev);
+}
+
+static void b43_phy_agcsetup(struct b43_wldev *dev)
+{
+ struct b43_phy *phy = &dev->phy;
+ u16 offset = 0x0000;
+
+ if (phy->rev == 1)
+ offset = 0x4C00;
+
+ b43_ofdmtab_write16(dev, offset, 0, 0x00FE);
+ b43_ofdmtab_write16(dev, offset, 1, 0x000D);
+ b43_ofdmtab_write16(dev, offset, 2, 0x0013);
+ b43_ofdmtab_write16(dev, offset, 3, 0x0019);
+
+ if (phy->rev == 1) {
+ b43_ofdmtab_write16(dev, 0x1800, 0, 0x2710);
+ b43_ofdmtab_write16(dev, 0x1801, 0, 0x9B83);
+ b43_ofdmtab_write16(dev, 0x1802, 0, 0x9B83);
+ b43_ofdmtab_write16(dev, 0x1803, 0, 0x0F8D);
+ b43_phy_write(dev, 0x0455, 0x0004);
+ }
+
+ b43_phy_write(dev, 0x04A5, (b43_phy_read(dev, 0x04A5)
+ & 0x00FF) | 0x5700);
+ b43_phy_write(dev, 0x041A, (b43_phy_read(dev, 0x041A)
+ & 0xFF80) | 0x000F);
+ b43_phy_write(dev, 0x041A, (b43_phy_read(dev, 0x041A)
+ & 0xC07F) | 0x2B80);
+ b43_phy_write(dev, 0x048C, (b43_phy_read(dev, 0x048C)
+ & 0xF0FF) | 0x0300);
+
+ b43_radio_write16(dev, 0x007A, b43_radio_read16(dev, 0x007A)
+ | 0x0008);
+
+ b43_phy_write(dev, 0x04A0, (b43_phy_read(dev, 0x04A0)
+ & 0xFFF0) | 0x0008);
+ b43_phy_write(dev, 0x04A1, (b43_phy_read(dev, 0x04A1)
+ & 0xF0FF) | 0x0600);
+ b43_phy_write(dev, 0x04A2, (b43_phy_read(dev, 0x04A2)
+ & 0xF0FF) | 0x0700);
+ b43_phy_write(dev, 0x04A0, (b43_phy_read(dev, 0x04A0)
+ & 0xF0FF) | 0x0100);
+
+ if (phy->rev == 1) {
+ b43_phy_write(dev, 0x04A2, (b43_phy_read(dev, 0x04A2)
+ & 0xFFF0) | 0x0007);
+ }
+
+ b43_phy_write(dev, 0x0488, (b43_phy_read(dev, 0x0488)
+ & 0xFF00) | 0x001C);
+ b43_phy_write(dev, 0x0488, (b43_phy_read(dev, 0x0488)
+ & 0xC0FF) | 0x0200);
+ b43_phy_write(dev, 0x0496, (b43_phy_read(dev, 0x0496)
+ & 0xFF00) | 0x001C);
+ b43_phy_write(dev, 0x0489, (b43_phy_read(dev, 0x0489)
+ & 0xFF00) | 0x0020);
+ b43_phy_write(dev, 0x0489, (b43_phy_read(dev, 0x0489)
+ & 0xC0FF) | 0x0200);
+ b43_phy_write(dev, 0x0482, (b43_phy_read(dev, 0x0482)
+ & 0xFF00) | 0x002E);
+ b43_phy_write(dev, 0x0496, (b43_phy_read(dev, 0x0496)
+ & 0x00FF) | 0x1A00);
+ b43_phy_write(dev, 0x0481, (b43_phy_read(dev, 0x0481)
+ & 0xFF00) | 0x0028);
+ b43_phy_write(dev, 0x0481, (b43_phy_read(dev, 0x0481)
+ & 0x00FF) | 0x2C00);
+
+ if (phy->rev == 1) {
+ b43_phy_write(dev, 0x0430, 0x092B);
+ b43_phy_write(dev, 0x041B, (b43_phy_read(dev, 0x041B)
+ & 0xFFE1) | 0x0002);
+ } else {
+ b43_phy_write(dev, 0x041B, b43_phy_read(dev, 0x041B)
+ & 0xFFE1);
+ b43_phy_write(dev, 0x041F, 0x287A);
+ b43_phy_write(dev, 0x0420, (b43_phy_read(dev, 0x0420)
+ & 0xFFF0) | 0x0004);
+ }
+
+ if (phy->rev >= 6) {
+ b43_phy_write(dev, 0x0422, 0x287A);
+ b43_phy_write(dev, 0x0420, (b43_phy_read(dev, 0x0420)
+ & 0x0FFF) | 0x3000);
+ }
+
+ b43_phy_write(dev, 0x04A8, (b43_phy_read(dev, 0x04A8)
+ & 0x8080) | 0x7874);
+ b43_phy_write(dev, 0x048E, 0x1C00);
+
+ offset = 0x0800;
+ if (phy->rev == 1) {
+ offset = 0x5400;
+ b43_phy_write(dev, 0x04AB, (b43_phy_read(dev, 0x04AB)
+ & 0xF0FF) | 0x0600);
+ b43_phy_write(dev, 0x048B, 0x005E);
+ b43_phy_write(dev, 0x048C, (b43_phy_read(dev, 0x048C)
+ & 0xFF00) | 0x001E);
+ b43_phy_write(dev, 0x048D, 0x0002);
+ }
+ b43_ofdmtab_write16(dev, offset, 0, 0x00);
+ b43_ofdmtab_write16(dev, offset, 1, 0x07);
+ b43_ofdmtab_write16(dev, offset, 2, 0x10);
+ b43_ofdmtab_write16(dev, offset, 3, 0x1C);
+
+ if (phy->rev >= 6) {
+ b43_phy_write(dev, 0x0426, b43_phy_read(dev, 0x0426)
+ & 0xFFFC);
+ b43_phy_write(dev, 0x0426, b43_phy_read(dev, 0x0426)
+ & 0xEFFF);
+ }
+}
+
+static void b43_phy_setupg(struct b43_wldev *dev)
+{
+ struct ssb_bus *bus = dev->dev->bus;
+ struct b43_phy *phy = &dev->phy;
+ u16 i;
+
+ B43_WARN_ON(phy->type != B43_PHYTYPE_G);
+ if (phy->rev == 1) {
+ b43_phy_write(dev, 0x0406, 0x4F19);
+ b43_phy_write(dev, B43_PHY_G_CRS,
+ (b43_phy_read(dev, B43_PHY_G_CRS) & 0xFC3F) |
+ 0x0340);
+ b43_phy_write(dev, 0x042C, 0x005A);
+ b43_phy_write(dev, 0x0427, 0x001A);
+
+ for (i = 0; i < B43_TAB_FINEFREQG_SIZE; i++)
+ b43_ofdmtab_write16(dev, 0x5800, i,
+ b43_tab_finefreqg[i]);
+ for (i = 0; i < B43_TAB_NOISEG1_SIZE; i++)
+ b43_ofdmtab_write16(dev, 0x1800, i, b43_tab_noiseg1[i]);
+ for (i = 0; i < B43_TAB_ROTOR_SIZE; i++)
+ b43_ofdmtab_write16(dev, 0x2000, i, b43_tab_rotor[i]);
+ } else {
+ /* nrssi values are signed 6-bit values. Not sure why we write 0x7654 here... */
+ b43_nrssi_hw_write(dev, 0xBA98, (s16) 0x7654);
+
+ if (phy->rev == 2) {
+ b43_phy_write(dev, 0x04C0, 0x1861);
+ b43_phy_write(dev, 0x04C1, 0x0271);
+ } else if (phy->rev > 2) {
+ b43_phy_write(dev, 0x04C0, 0x0098);
+ b43_phy_write(dev, 0x04C1, 0x0070);
+ b43_phy_write(dev, 0x04C9, 0x0080);
+ }
+ b43_phy_write(dev, 0x042B, b43_phy_read(dev, 0x042B) | 0x800);
+
+ for (i = 0; i < 64; i++)
+ b43_ofdmtab_write16(dev, 0x4000, i, i);
+ for (i = 0; i < B43_TAB_NOISEG2_SIZE; i++)
+ b43_ofdmtab_write16(dev, 0x1800, i, b43_tab_noiseg2[i]);
+ }
+
+ if (phy->rev <= 2)
+ for (i = 0; i < B43_TAB_NOISESCALEG_SIZE; i++)
+ b43_ofdmtab_write16(dev, 0x1400, i,
+ b43_tab_noisescaleg1[i]);
+ else if ((phy->rev >= 7) && (b43_phy_read(dev, 0x0449) & 0x0200))
+ for (i = 0; i < B43_TAB_NOISESCALEG_SIZE; i++)
+ b43_ofdmtab_write16(dev, 0x1400, i,
+ b43_tab_noisescaleg3[i]);
+ else
+ for (i = 0; i < B43_TAB_NOISESCALEG_SIZE; i++)
+ b43_ofdmtab_write16(dev, 0x1400, i,
+ b43_tab_noisescaleg2[i]);
+
+ if (phy->rev == 2)
+ for (i = 0; i < B43_TAB_SIGMASQR_SIZE; i++)
+ b43_ofdmtab_write16(dev, 0x5000, i,
+ b43_tab_sigmasqr1[i]);
+ else if ((phy->rev > 2) && (phy->rev <= 8))
+ for (i = 0; i < B43_TAB_SIGMASQR_SIZE; i++)
+ b43_ofdmtab_write16(dev, 0x5000, i,
+ b43_tab_sigmasqr2[i]);
+
+ if (phy->rev == 1) {
+ for (i = 0; i < B43_TAB_RETARD_SIZE; i++)
+ b43_ofdmtab_write32(dev, 0x2400, i, b43_tab_retard[i]);
+ for (i = 4; i < 20; i++)
+ b43_ofdmtab_write16(dev, 0x5400, i, 0x0020);
+ b43_phy_agcsetup(dev);
+
+ if ((bus->boardinfo.vendor == SSB_BOARDVENDOR_BCM) &&
+ (bus->boardinfo.type == SSB_BOARD_BU4306) &&
+ (bus->boardinfo.rev == 0x17))
+ return;
+
+ b43_ofdmtab_write16(dev, 0x5001, 0, 0x0002);
+ b43_ofdmtab_write16(dev, 0x5002, 0, 0x0001);
+ } else {
+ for (i = 0; i < 0x20; i++)
+ b43_ofdmtab_write16(dev, 0x1000, i, 0x0820);
+ b43_phy_agcsetup(dev);
+ b43_phy_read(dev, 0x0400); /* dummy read */
+ b43_phy_write(dev, 0x0403, 0x1000);
+ b43_ofdmtab_write16(dev, 0x3C02, 0, 0x000F);
+ b43_ofdmtab_write16(dev, 0x3C03, 0, 0x0014);
+
+ if ((bus->boardinfo.vendor == SSB_BOARDVENDOR_BCM) &&
+ (bus->boardinfo.type == SSB_BOARD_BU4306) &&
+ (bus->boardinfo.rev == 0x17))
+ return;
+
+ b43_ofdmtab_write16(dev, 0x0401, 0, 0x0002);
+ b43_ofdmtab_write16(dev, 0x0402, 0, 0x0001);
+ }
+}
+
+/* Initialize the noisescaletable for APHY */
+static void b43_phy_init_noisescaletbl(struct b43_wldev *dev)
+{
+ struct b43_phy *phy = &dev->phy;
+ int i;
+
+ for (i = 0; i < 12; i++) {
+ if (phy->rev == 2)
+ b43_ofdmtab_write16(dev, 0x1400, i, 0x6767);
+ else
+ b43_ofdmtab_write16(dev, 0x1400, i, 0x2323);
+ }
+ if (phy->rev == 2)
+ b43_ofdmtab_write16(dev, 0x1400, i, 0x6700);
+ else
+ b43_ofdmtab_write16(dev, 0x1400, i, 0x2300);
+ for (i = 0; i < 11; i++) {
+ if (phy->rev == 2)
+ b43_ofdmtab_write16(dev, 0x1400, i, 0x6767);
+ else
+ b43_ofdmtab_write16(dev, 0x1400, i, 0x2323);
+ }
+ if (phy->rev == 2)
+ b43_ofdmtab_write16(dev, 0x1400, i, 0x0067);
+ else
+ b43_ofdmtab_write16(dev, 0x1400, i, 0x0023);
+}
+
+static void b43_phy_setupa(struct b43_wldev *dev)
+{
+ struct b43_phy *phy = &dev->phy;
+ u16 i;
+
+ B43_WARN_ON(phy->type != B43_PHYTYPE_A);
+ switch (phy->rev) {
+ case 2:
+ b43_phy_write(dev, 0x008E, 0x3800);
+ b43_phy_write(dev, 0x0035, 0x03FF);
+ b43_phy_write(dev, 0x0036, 0x0400);
+
+ b43_ofdmtab_write16(dev, 0x3807, 0, 0x0051);
+
+ b43_phy_write(dev, 0x001C, 0x0FF9);
+ b43_phy_write(dev, 0x0020, b43_phy_read(dev, 0x0020) & 0xFF0F);
+ b43_ofdmtab_write16(dev, 0x3C0C, 0, 0x07BF);
+ b43_radio_write16(dev, 0x0002, 0x07BF);
+
+ b43_phy_write(dev, 0x0024, 0x4680);
+ b43_phy_write(dev, 0x0020, 0x0003);
+ b43_phy_write(dev, 0x001D, 0x0F40);
+ b43_phy_write(dev, 0x001F, 0x1C00);
+
+ b43_phy_write(dev, 0x002A, (b43_phy_read(dev, 0x002A)
+ & 0x00FF) | 0x0400);
+ b43_phy_write(dev, 0x002B, b43_phy_read(dev, 0x002B)
+ & 0xFBFF);
+ b43_phy_write(dev, 0x008E, 0x58C1);
+
+ b43_ofdmtab_write16(dev, 0x0803, 0, 0x000F);
+ b43_ofdmtab_write16(dev, 0x0804, 0, 0x001F);
+ b43_ofdmtab_write16(dev, 0x0805, 0, 0x002A);
+ b43_ofdmtab_write16(dev, 0x0805, 0, 0x0030);
+ b43_ofdmtab_write16(dev, 0x0807, 0, 0x003A);
+
+ b43_ofdmtab_write16(dev, 0x0000, 0, 0x0013);
+ b43_ofdmtab_write16(dev, 0x0000, 1, 0x0013);
+ b43_ofdmtab_write16(dev, 0x0000, 2, 0x0013);
+ b43_ofdmtab_write16(dev, 0x0000, 3, 0x0013);
+ b43_ofdmtab_write16(dev, 0x0000, 4, 0x0015);
+ b43_ofdmtab_write16(dev, 0x0000, 5, 0x0015);
+ b43_ofdmtab_write16(dev, 0x0000, 6, 0x0019);
+
+ b43_ofdmtab_write16(dev, 0x0404, 0, 0x0003);
+ b43_ofdmtab_write16(dev, 0x0405, 0, 0x0003);
+ b43_ofdmtab_write16(dev, 0x0406, 0, 0x0007);
+
+ for (i = 0; i < 16; i++)
+ b43_ofdmtab_write16(dev, 0x4000, i, (0x8 + i) & 0x000F);
+
+ b43_ofdmtab_write16(dev, 0x3003, 0, 0x1044);
+ b43_ofdmtab_write16(dev, 0x3004, 0, 0x7201);
+ b43_ofdmtab_write16(dev, 0x3006, 0, 0x0040);
+ b43_ofdmtab_write16(dev, 0x3001, 0,
+ (b43_ofdmtab_read16(dev, 0x3001, 0) &
+ 0x0010) | 0x0008);
+
+ for (i = 0; i < B43_TAB_FINEFREQA_SIZE; i++)
+ b43_ofdmtab_write16(dev, 0x5800, i,
+ b43_tab_finefreqa[i]);
+ for (i = 0; i < B43_TAB_NOISEA2_SIZE; i++)
+ b43_ofdmtab_write16(dev, 0x1800, i, b43_tab_noisea2[i]);
+ for (i = 0; i < B43_TAB_ROTOR_SIZE; i++)
+ b43_ofdmtab_write32(dev, 0x2000, i, b43_tab_rotor[i]);
+ b43_phy_init_noisescaletbl(dev);
+ for (i = 0; i < B43_TAB_RETARD_SIZE; i++)
+ b43_ofdmtab_write32(dev, 0x2400, i, b43_tab_retard[i]);
+ break;
+ case 3:
+ for (i = 0; i < 64; i++)
+ b43_ofdmtab_write16(dev, 0x4000, i, i);
+
+ b43_ofdmtab_write16(dev, 0x3807, 0, 0x0051);
+
+ b43_phy_write(dev, 0x001C, 0x0FF9);
+ b43_phy_write(dev, 0x0020, b43_phy_read(dev, 0x0020) & 0xFF0F);
+ b43_radio_write16(dev, 0x0002, 0x07BF);
+
+ b43_phy_write(dev, 0x0024, 0x4680);
+ b43_phy_write(dev, 0x0020, 0x0003);
+ b43_phy_write(dev, 0x001D, 0x0F40);
+ b43_phy_write(dev, 0x001F, 0x1C00);
+ b43_phy_write(dev, 0x002A, (b43_phy_read(dev, 0x002A)
+ & 0x00FF) | 0x0400);
+
+ b43_ofdmtab_write16(dev, 0x3000, 1,
+ (b43_ofdmtab_read16(dev, 0x3000, 1)
+ & 0x0010) | 0x0008);
+ for (i = 0; i < B43_TAB_NOISEA3_SIZE; i++) {
+ b43_ofdmtab_write16(dev, 0x1800, i, b43_tab_noisea3[i]);
+ }
+ b43_phy_init_noisescaletbl(dev);
+ for (i = 0; i < B43_TAB_SIGMASQR_SIZE; i++) {
+ b43_ofdmtab_write16(dev, 0x5000, i,
+ b43_tab_sigmasqr1[i]);
+ }
+
+ b43_phy_write(dev, 0x0003, 0x1808);
+
+ b43_ofdmtab_write16(dev, 0x0803, 0, 0x000F);
+ b43_ofdmtab_write16(dev, 0x0804, 0, 0x001F);
+ b43_ofdmtab_write16(dev, 0x0805, 0, 0x002A);
+ b43_ofdmtab_write16(dev, 0x0805, 0, 0x0030);
+ b43_ofdmtab_write16(dev, 0x0807, 0, 0x003A);
+
+ b43_ofdmtab_write16(dev, 0x0000, 0, 0x0013);
+ b43_ofdmtab_write16(dev, 0x0001, 0, 0x0013);
+ b43_ofdmtab_write16(dev, 0x0002, 0, 0x0013);
+ b43_ofdmtab_write16(dev, 0x0003, 0, 0x0013);
+ b43_ofdmtab_write16(dev, 0x0004, 0, 0x0015);
+ b43_ofdmtab_write16(dev, 0x0005, 0, 0x0015);
+ b43_ofdmtab_write16(dev, 0x0006, 0, 0x0019);
+
+ b43_ofdmtab_write16(dev, 0x0404, 0, 0x0003);
+ b43_ofdmtab_write16(dev, 0x0405, 0, 0x0003);
+ b43_ofdmtab_write16(dev, 0x0406, 0, 0x0007);
+
+ b43_ofdmtab_write16(dev, 0x3C02, 0, 0x000F);
+ b43_ofdmtab_write16(dev, 0x3C03, 0, 0x0014);
+ break;
+ default:
+ B43_WARN_ON(1);
+ }
+}
+
+/* Initialize APHY. This is also called for the GPHY in some cases. */
+static void b43_phy_inita(struct b43_wldev *dev)
+{
+ struct ssb_bus *bus = dev->dev->bus;
+ struct b43_phy *phy = &dev->phy;
+ u16 tval;
+
+ might_sleep();
+
+ if (phy->type == B43_PHYTYPE_A) {
+ b43_phy_setupa(dev);
+ } else {
+ b43_phy_setupg(dev);
+ if (phy->gmode &&
+ (dev->dev->bus->sprom.r1.boardflags_lo & B43_BFL_PACTRL))
+ b43_phy_write(dev, 0x046E, 0x03CF);
+ return;
+ }
+
+ b43_phy_write(dev, B43_PHY_A_CRS,
+ (b43_phy_read(dev, B43_PHY_A_CRS) & 0xF83C) | 0x0340);
+ b43_phy_write(dev, 0x0034, 0x0001);
+
+ //TODO: RSSI AGC
+ b43_phy_write(dev, B43_PHY_A_CRS,
+ b43_phy_read(dev, B43_PHY_A_CRS) | (1 << 14));
+ b43_radio_init2060(dev);
+
+ if ((bus->boardinfo.vendor == SSB_BOARDVENDOR_BCM) &&
+ ((bus->boardinfo.type == SSB_BOARD_BU4306) ||
+ (bus->boardinfo.type == SSB_BOARD_BU4309))) {
+ if (phy->lofcal == 0xFFFF) {
+ //TODO: LOF Cal
+ b43_radio_set_tx_iq(dev);
+ } else
+ b43_radio_write16(dev, 0x001E, phy->lofcal);
+ }
+
+ b43_phy_write(dev, 0x007A, 0xF111);
+
+ if (phy->cur_idle_tssi == 0) {
+ b43_radio_write16(dev, 0x0019, 0x0000);
+ b43_radio_write16(dev, 0x0017, 0x0020);
+
+ tval = b43_ofdmtab_read16(dev, 0x3001, 0);
+ if (phy->rev == 1) {
+ b43_ofdmtab_write16(dev, 0x3001, 0,
+ (b43_ofdmtab_read16(dev, 0x3001, 0)
+ & 0xFF87)
+ | 0x0058);
+ } else {
+ b43_ofdmtab_write16(dev, 0x3001, 0,
+ (b43_ofdmtab_read16(dev, 0x3001, 0)
+ & 0xFFC3)
+ | 0x002C);
+ }
+ b43_dummy_transmission(dev);
+ phy->cur_idle_tssi = b43_phy_read(dev, B43_PHY_A_PCTL);
+ b43_ofdmtab_write16(dev, 0x3001, 0, tval);
+
+ b43_radio_set_txpower_a(dev, 0x0018);
+ }
+ b43_shm_clear_tssi(dev);
+}
+
+static void b43_phy_initb2(struct b43_wldev *dev)
+{
+ struct b43_phy *phy = &dev->phy;
+ u16 offset, val;
+
+ b43_write16(dev, 0x03EC, 0x3F22);
+ b43_phy_write(dev, 0x0020, 0x301C);
+ b43_phy_write(dev, 0x0026, 0x0000);
+ b43_phy_write(dev, 0x0030, 0x00C6);
+ b43_phy_write(dev, 0x0088, 0x3E00);
+ val = 0x3C3D;
+ for (offset = 0x0089; offset < 0x00A7; offset++) {
+ b43_phy_write(dev, offset, val);
+ val -= 0x0202;
+ }
+ b43_phy_write(dev, 0x03E4, 0x3000);
+ if (phy->channel == 0xFF)
+ b43_radio_selectchannel(dev, B43_DEFAULT_CHANNEL_BG, 0);
+ else
+ b43_radio_selectchannel(dev, phy->channel, 0);
+ if (phy->radio_ver != 0x2050) {
+ b43_radio_write16(dev, 0x0075, 0x0080);
+ b43_radio_write16(dev, 0x0079, 0x0081);
+ }
+ b43_radio_write16(dev, 0x0050, 0x0020);
+ b43_radio_write16(dev, 0x0050, 0x0023);
+ if (phy->radio_ver == 0x2050) {
+ b43_radio_write16(dev, 0x0050, 0x0020);
+ b43_radio_write16(dev, 0x005A, 0x0070);
+ b43_radio_write16(dev, 0x005B, 0x007B);
+ b43_radio_write16(dev, 0x005C, 0x00B0);
+ b43_radio_write16(dev, 0x007A, 0x000F);
+ b43_phy_write(dev, 0x0038, 0x0677);
+ b43_radio_init2050(dev);
+ }
+ b43_phy_write(dev, 0x0014, 0x0080);
+ b43_phy_write(dev, 0x0032, 0x00CA);
+ b43_phy_write(dev, 0x0032, 0x00CC);
+ b43_phy_write(dev, 0x0035, 0x07C2);
+ b43_lo_b_measure(dev);
+ b43_phy_write(dev, 0x0026, 0xCC00);
+ if (phy->radio_ver != 0x2050)
+ b43_phy_write(dev, 0x0026, 0xCE00);
+ b43_write16(dev, B43_MMIO_CHANNEL_EXT, 0x1000);
+ b43_phy_write(dev, 0x002A, 0x88A3);
+ if (phy->radio_ver != 0x2050)
+ b43_phy_write(dev, 0x002A, 0x88C2);
+ b43_set_txpower_g(dev, &phy->bbatt, &phy->rfatt, phy->tx_control);
+ b43_phy_init_pctl(dev);
+}
+
+static void b43_phy_initb4(struct b43_wldev *dev)
+{
+ struct b43_phy *phy = &dev->phy;
+ u16 offset, val;
+
+ b43_write16(dev, 0x03EC, 0x3F22);
+ b43_phy_write(dev, 0x0020, 0x301C);
+ b43_phy_write(dev, 0x0026, 0x0000);
+ b43_phy_write(dev, 0x0030, 0x00C6);
+ b43_phy_write(dev, 0x0088, 0x3E00);
+ val = 0x3C3D;
+ for (offset = 0x0089; offset < 0x00A7; offset++) {
+ b43_phy_write(dev, offset, val);
+ val -= 0x0202;
+ }
+ b43_phy_write(dev, 0x03E4, 0x3000);
+ if (phy->channel == 0xFF)
+ b43_radio_selectchannel(dev, B43_DEFAULT_CHANNEL_BG, 0);
+ else
+ b43_radio_selectchannel(dev, phy->channel, 0);
+ if (phy->radio_ver != 0x2050) {
+ b43_radio_write16(dev, 0x0075, 0x0080);
+ b43_radio_write16(dev, 0x0079, 0x0081);
+ }
+ b43_radio_write16(dev, 0x0050, 0x0020);
+ b43_radio_write16(dev, 0x0050, 0x0023);
+ if (phy->radio_ver == 0x2050) {
+ b43_radio_write16(dev, 0x0050, 0x0020);
+ b43_radio_write16(dev, 0x005A, 0x0070);
+ b43_radio_write16(dev, 0x005B, 0x007B);
+ b43_radio_write16(dev, 0x005C, 0x00B0);
+ b43_radio_write16(dev, 0x007A, 0x000F);
+ b43_phy_write(dev, 0x0038, 0x0677);
+ b43_radio_init2050(dev);
+ }
+ b43_phy_write(dev, 0x0014, 0x0080);
+ b43_phy_write(dev, 0x0032, 0x00CA);
+ if (phy->radio_ver == 0x2050)
+ b43_phy_write(dev, 0x0032, 0x00E0);
+ b43_phy_write(dev, 0x0035, 0x07C2);
+
+ b43_lo_b_measure(dev);
+
+ b43_phy_write(dev, 0x0026, 0xCC00);
+ if (phy->radio_ver == 0x2050)
+ b43_phy_write(dev, 0x0026, 0xCE00);
+ b43_write16(dev, B43_MMIO_CHANNEL_EXT, 0x1100);
+ b43_phy_write(dev, 0x002A, 0x88A3);
+ if (phy->radio_ver == 0x2050)
+ b43_phy_write(dev, 0x002A, 0x88C2);
+ b43_set_txpower_g(dev, &phy->bbatt, &phy->rfatt, phy->tx_control);
+ if (dev->dev->bus->sprom.r1.boardflags_lo & B43_BFL_RSSI) {
+ b43_calc_nrssi_slope(dev);
+ b43_calc_nrssi_threshold(dev);
+ }
+ b43_phy_init_pctl(dev);
+}
+
+static void b43_phy_initb5(struct b43_wldev *dev)
+{
+ struct ssb_bus *bus = dev->dev->bus;
+ struct b43_phy *phy = &dev->phy;
+ u16 offset, value;
+ u8 old_channel;
+
+ if (phy->analog == 1) {
+ b43_radio_write16(dev, 0x007A, b43_radio_read16(dev, 0x007A)
+ | 0x0050);
+ }
+ if ((bus->boardinfo.vendor != SSB_BOARDVENDOR_BCM) &&
+ (bus->boardinfo.type != SSB_BOARD_BU4306)) {
+ value = 0x2120;
+ for (offset = 0x00A8; offset < 0x00C7; offset++) {
+ b43_phy_write(dev, offset, value);
+ value += 0x202;
+ }
+ }
+ b43_phy_write(dev, 0x0035, (b43_phy_read(dev, 0x0035) & 0xF0FF)
+ | 0x0700);
+ if (phy->radio_ver == 0x2050)
+ b43_phy_write(dev, 0x0038, 0x0667);
+
+ if (phy->gmode || phy->rev >= 2) {
+ if (phy->radio_ver == 0x2050) {
+ b43_radio_write16(dev, 0x007A,
+ b43_radio_read16(dev, 0x007A)
+ | 0x0020);
+ b43_radio_write16(dev, 0x0051,
+ b43_radio_read16(dev, 0x0051)
+ | 0x0004);
+ }
+ b43_write16(dev, B43_MMIO_PHY_RADIO, 0x0000);
+
+ b43_phy_write(dev, 0x0802, b43_phy_read(dev, 0x0802) | 0x0100);
+ b43_phy_write(dev, 0x042B, b43_phy_read(dev, 0x042B) | 0x2000);
+
+ b43_phy_write(dev, 0x001C, 0x186A);
+
+ b43_phy_write(dev, 0x0013,
+ (b43_phy_read(dev, 0x0013) & 0x00FF) | 0x1900);
+ b43_phy_write(dev, 0x0035,
+ (b43_phy_read(dev, 0x0035) & 0xFFC0) | 0x0064);
+ b43_phy_write(dev, 0x005D,
+ (b43_phy_read(dev, 0x005D) & 0xFF80) | 0x000A);
+ }
+
+ if (dev->bad_frames_preempt) {
+ b43_phy_write(dev, B43_PHY_RADIO_BITFIELD,
+ b43_phy_read(dev,
+ B43_PHY_RADIO_BITFIELD) | (1 << 11));
+ }
+
+ if (phy->analog == 1) {
+ b43_phy_write(dev, 0x0026, 0xCE00);
+ b43_phy_write(dev, 0x0021, 0x3763);
+ b43_phy_write(dev, 0x0022, 0x1BC3);
+ b43_phy_write(dev, 0x0023, 0x06F9);
+ b43_phy_write(dev, 0x0024, 0x037E);
+ } else
+ b43_phy_write(dev, 0x0026, 0xCC00);
+ b43_phy_write(dev, 0x0030, 0x00C6);
+ b43_write16(dev, 0x03EC, 0x3F22);
+
+ if (phy->analog == 1)
+ b43_phy_write(dev, 0x0020, 0x3E1C);
+ else
+ b43_phy_write(dev, 0x0020, 0x301C);
+
+ if (phy->analog == 0)
+ b43_write16(dev, 0x03E4, 0x3000);
+
+ old_channel = phy->channel;
+ /* Force to channel 7, even if not supported. */
+ b43_radio_selectchannel(dev, 7, 0);
+
+ if (phy->radio_ver != 0x2050) {
+ b43_radio_write16(dev, 0x0075, 0x0080);
+ b43_radio_write16(dev, 0x0079, 0x0081);
+ }
+
+ b43_radio_write16(dev, 0x0050, 0x0020);
+ b43_radio_write16(dev, 0x0050, 0x0023);
+
+ if (phy->radio_ver == 0x2050) {
+ b43_radio_write16(dev, 0x0050, 0x0020);
+ b43_radio_write16(dev, 0x005A, 0x0070);
+ }
+
+ b43_radio_write16(dev, 0x005B, 0x007B);
+ b43_radio_write16(dev, 0x005C, 0x00B0);
+
+ b43_radio_write16(dev, 0x007A, b43_radio_read16(dev, 0x007A) | 0x0007);
+
+ b43_radio_selectchannel(dev, old_channel, 0);
+
+ b43_phy_write(dev, 0x0014, 0x0080);
+ b43_phy_write(dev, 0x0032, 0x00CA);
+ b43_phy_write(dev, 0x002A, 0x88A3);
+
+ b43_set_txpower_g(dev, &phy->bbatt, &phy->rfatt, phy->tx_control);
+
+ if (phy->radio_ver == 0x2050)
+ b43_radio_write16(dev, 0x005D, 0x000D);
+
+ b43_write16(dev, 0x03E4, (b43_read16(dev, 0x03E4) & 0xFFC0) | 0x0004);
+}
+
+static void b43_phy_initb6(struct b43_wldev *dev)
+{
+ struct b43_phy *phy = &dev->phy;
+ u16 offset, val;
+ u8 old_channel;
+
+ b43_phy_write(dev, 0x003E, 0x817A);
+ b43_radio_write16(dev, 0x007A,
+ (b43_radio_read16(dev, 0x007A) | 0x0058));
+ if (phy->radio_rev == 4 || phy->radio_rev == 5) {
+ b43_radio_write16(dev, 0x51, 0x37);
+ b43_radio_write16(dev, 0x52, 0x70);
+ b43_radio_write16(dev, 0x53, 0xB3);
+ b43_radio_write16(dev, 0x54, 0x9B);
+ b43_radio_write16(dev, 0x5A, 0x88);
+ b43_radio_write16(dev, 0x5B, 0x88);
+ b43_radio_write16(dev, 0x5D, 0x88);
+ b43_radio_write16(dev, 0x5E, 0x88);
+ b43_radio_write16(dev, 0x7D, 0x88);
+ b43_hf_write(dev, b43_hf_read(dev)
+ | B43_HF_TSSIRPSMW);
+ }
+ B43_WARN_ON(phy->radio_rev == 6 || phy->radio_rev == 7); /* We had code for these revs here... */
+ if (phy->radio_rev == 8) {
+ b43_radio_write16(dev, 0x51, 0);
+ b43_radio_write16(dev, 0x52, 0x40);
+ b43_radio_write16(dev, 0x53, 0xB7);
+ b43_radio_write16(dev, 0x54, 0x98);
+ b43_radio_write16(dev, 0x5A, 0x88);
+ b43_radio_write16(dev, 0x5B, 0x6B);
+ b43_radio_write16(dev, 0x5C, 0x0F);
+ if (dev->dev->bus->sprom.r1.boardflags_lo & B43_BFL_ALTIQ) {
+ b43_radio_write16(dev, 0x5D, 0xFA);
+ b43_radio_write16(dev, 0x5E, 0xD8);
+ } else {
+ b43_radio_write16(dev, 0x5D, 0xF5);
+ b43_radio_write16(dev, 0x5E, 0xB8);
+ }
+ b43_radio_write16(dev, 0x0073, 0x0003);
+ b43_radio_write16(dev, 0x007D, 0x00A8);
+ b43_radio_write16(dev, 0x007C, 0x0001);
+ b43_radio_write16(dev, 0x007E, 0x0008);
+ }
+ val = 0x1E1F;
+ for (offset = 0x0088; offset < 0x0098; offset++) {
+ b43_phy_write(dev, offset, val);
+ val -= 0x0202;
+ }
+ val = 0x3E3F;
+ for (offset = 0x0098; offset < 0x00A8; offset++) {
+ b43_phy_write(dev, offset, val);
+ val -= 0x0202;
+ }
+ val = 0x2120;
+ for (offset = 0x00A8; offset < 0x00C8; offset++) {
+ b43_phy_write(dev, offset, (val & 0x3F3F));
+ val += 0x0202;
+ }
+ if (phy->type == B43_PHYTYPE_G) {
+ b43_radio_write16(dev, 0x007A,
+ b43_radio_read16(dev, 0x007A) | 0x0020);
+ b43_radio_write16(dev, 0x0051,
+ b43_radio_read16(dev, 0x0051) | 0x0004);
+ b43_phy_write(dev, 0x0802, b43_phy_read(dev, 0x0802) | 0x0100);
+ b43_phy_write(dev, 0x042B, b43_phy_read(dev, 0x042B) | 0x2000);
+ b43_phy_write(dev, 0x5B, 0);
+ b43_phy_write(dev, 0x5C, 0);
+ }
+
+ old_channel = phy->channel;
+ if (old_channel >= 8)
+ b43_radio_selectchannel(dev, 1, 0);
+ else
+ b43_radio_selectchannel(dev, 13, 0);
+
+ b43_radio_write16(dev, 0x0050, 0x0020);
+ b43_radio_write16(dev, 0x0050, 0x0023);
+ udelay(40);
+ if (phy->radio_rev < 6 || phy->radio_rev == 8) {
+ b43_radio_write16(dev, 0x7C, (b43_radio_read16(dev, 0x7C)
+ | 0x0002));
+ b43_radio_write16(dev, 0x50, 0x20);
+ }
+ if (phy->radio_rev <= 2) {
+ b43_radio_write16(dev, 0x7C, 0x20);
+ b43_radio_write16(dev, 0x5A, 0x70);
+ b43_radio_write16(dev, 0x5B, 0x7B);
+ b43_radio_write16(dev, 0x5C, 0xB0);
+ }
+ b43_radio_write16(dev, 0x007A,
+ (b43_radio_read16(dev, 0x007A) & 0x00F8) | 0x0007);
+
+ b43_radio_selectchannel(dev, old_channel, 0);
+
+ b43_phy_write(dev, 0x0014, 0x0200);
+ if (phy->radio_rev >= 6)
+ b43_phy_write(dev, 0x2A, 0x88C2);
+ else
+ b43_phy_write(dev, 0x2A, 0x8AC0);
+ b43_phy_write(dev, 0x0038, 0x0668);
+ b43_set_txpower_g(dev, &phy->bbatt, &phy->rfatt, phy->tx_control);
+ if (phy->radio_rev <= 5) {
+ b43_phy_write(dev, 0x5D, (b43_phy_read(dev, 0x5D)
+ & 0xFF80) | 0x0003);
+ }
+ if (phy->radio_rev <= 2)
+ b43_radio_write16(dev, 0x005D, 0x000D);
+
+ if (phy->analog == 4) {
+ b43_write16(dev, 0x3E4, 9);
+ b43_phy_write(dev, 0x61, b43_phy_read(dev, 0x61)
+ & 0x0FFF);
+ } else {
+ b43_phy_write(dev, 0x0002, (b43_phy_read(dev, 0x0002) & 0xFFC0)
+ | 0x0004);
+ }
+ if (phy->type == B43_PHYTYPE_B) {
+ b43_write16(dev, 0x03E6, 0x8140);
+ b43_phy_write(dev, 0x0016, 0x0410);
+ b43_phy_write(dev, 0x0017, 0x0820);
+ b43_phy_write(dev, 0x0062, 0x0007);
+ b43_radio_init2050(dev);
+ b43_lo_g_measure(dev);
+ if (dev->dev->bus->sprom.r1.boardflags_lo & B43_BFL_RSSI) {
+ b43_calc_nrssi_slope(dev);
+ b43_calc_nrssi_threshold(dev);
+ }
+ b43_phy_init_pctl(dev);
+ } else if (phy->type == B43_PHYTYPE_G)
+ b43_write16(dev, 0x03E6, 0x0);
+}
+
+static void b43_calc_loopback_gain(struct b43_wldev *dev)
+{
+ struct b43_phy *phy = &dev->phy;
+ u16 backup_phy[16] = { 0 };
+ u16 backup_radio[3];
+ u16 backup_bband;
+ u16 i, j, loop_i_max;
+ u16 trsw_rx;
+ u16 loop1_outer_done, loop1_inner_done;
+
+ backup_phy[0] = b43_phy_read(dev, B43_PHY_CRS0);
+ backup_phy[1] = b43_phy_read(dev, B43_PHY_CCKBBANDCFG);
+ backup_phy[2] = b43_phy_read(dev, B43_PHY_RFOVER);
+ backup_phy[3] = b43_phy_read(dev, B43_PHY_RFOVERVAL);
+ if (phy->rev != 1) { /* Not in specs, but needed to prevent PPC machine check */
+ backup_phy[4] = b43_phy_read(dev, B43_PHY_ANALOGOVER);
+ backup_phy[5] = b43_phy_read(dev, B43_PHY_ANALOGOVERVAL);
+ }
+ backup_phy[6] = b43_phy_read(dev, B43_PHY_BASE(0x5A));
+ backup_phy[7] = b43_phy_read(dev, B43_PHY_BASE(0x59));
+ backup_phy[8] = b43_phy_read(dev, B43_PHY_BASE(0x58));
+ backup_phy[9] = b43_phy_read(dev, B43_PHY_BASE(0x0A));
+ backup_phy[10] = b43_phy_read(dev, B43_PHY_BASE(0x03));
+ backup_phy[11] = b43_phy_read(dev, B43_PHY_LO_MASK);
+ backup_phy[12] = b43_phy_read(dev, B43_PHY_LO_CTL);
+ backup_phy[13] = b43_phy_read(dev, B43_PHY_BASE(0x2B));
+ backup_phy[14] = b43_phy_read(dev, B43_PHY_PGACTL);
+ backup_phy[15] = b43_phy_read(dev, B43_PHY_LO_LEAKAGE);
+ backup_bband = phy->bbatt.att;
+ backup_radio[0] = b43_radio_read16(dev, 0x52);
+ backup_radio[1] = b43_radio_read16(dev, 0x43);
+ backup_radio[2] = b43_radio_read16(dev, 0x7A);
+
+ b43_phy_write(dev, B43_PHY_CRS0,
+ b43_phy_read(dev, B43_PHY_CRS0) & 0x3FFF);
+ b43_phy_write(dev, B43_PHY_CCKBBANDCFG,
+ b43_phy_read(dev, B43_PHY_CCKBBANDCFG) | 0x8000);
+ b43_phy_write(dev, B43_PHY_RFOVER,
+ b43_phy_read(dev, B43_PHY_RFOVER) | 0x0002);
+ b43_phy_write(dev, B43_PHY_RFOVERVAL,
+ b43_phy_read(dev, B43_PHY_RFOVERVAL) & 0xFFFD);
+ b43_phy_write(dev, B43_PHY_RFOVER,
+ b43_phy_read(dev, B43_PHY_RFOVER) | 0x0001);
+ b43_phy_write(dev, B43_PHY_RFOVERVAL,
+ b43_phy_read(dev, B43_PHY_RFOVERVAL) & 0xFFFE);
+ if (phy->rev != 1) { /* Not in specs, but needed to prevent PPC machine check */
+ b43_phy_write(dev, B43_PHY_ANALOGOVER,
+ b43_phy_read(dev, B43_PHY_ANALOGOVER) | 0x0001);
+ b43_phy_write(dev, B43_PHY_ANALOGOVERVAL,
+ b43_phy_read(dev,
+ B43_PHY_ANALOGOVERVAL) & 0xFFFE);
+ b43_phy_write(dev, B43_PHY_ANALOGOVER,
+ b43_phy_read(dev, B43_PHY_ANALOGOVER) | 0x0002);
+ b43_phy_write(dev, B43_PHY_ANALOGOVERVAL,
+ b43_phy_read(dev,
+ B43_PHY_ANALOGOVERVAL) & 0xFFFD);
+ }
+ b43_phy_write(dev, B43_PHY_RFOVER,
+ b43_phy_read(dev, B43_PHY_RFOVER) | 0x000C);
+ b43_phy_write(dev, B43_PHY_RFOVERVAL,
+ b43_phy_read(dev, B43_PHY_RFOVERVAL) | 0x000C);
+ b43_phy_write(dev, B43_PHY_RFOVER,
+ b43_phy_read(dev, B43_PHY_RFOVER) | 0x0030);
+ b43_phy_write(dev, B43_PHY_RFOVERVAL,
+ (b43_phy_read(dev, B43_PHY_RFOVERVAL)
+ & 0xFFCF) | 0x10);
+
+ b43_phy_write(dev, B43_PHY_BASE(0x5A), 0x0780);
+ b43_phy_write(dev, B43_PHY_BASE(0x59), 0xC810);
+ b43_phy_write(dev, B43_PHY_BASE(0x58), 0x000D);
+
+ b43_phy_write(dev, B43_PHY_BASE(0x0A),
+ b43_phy_read(dev, B43_PHY_BASE(0x0A)) | 0x2000);
+ if (phy->rev != 1) { /* Not in specs, but needed to prevent PPC machine check */
+ b43_phy_write(dev, B43_PHY_ANALOGOVER,
+ b43_phy_read(dev, B43_PHY_ANALOGOVER) | 0x0004);
+ b43_phy_write(dev, B43_PHY_ANALOGOVERVAL,
+ b43_phy_read(dev,
+ B43_PHY_ANALOGOVERVAL) & 0xFFFB);
+ }
+ b43_phy_write(dev, B43_PHY_BASE(0x03),
+ (b43_phy_read(dev, B43_PHY_BASE(0x03))
+ & 0xFF9F) | 0x40);
+
+ if (phy->radio_rev == 8) {
+ b43_radio_write16(dev, 0x43, 0x000F);
+ } else {
+ b43_radio_write16(dev, 0x52, 0);
+ b43_radio_write16(dev, 0x43, (b43_radio_read16(dev, 0x43)
+ & 0xFFF0) | 0x9);
+ }
+ b43_phy_set_baseband_attenuation(dev, 11);
+
+ if (phy->rev >= 3)
+ b43_phy_write(dev, B43_PHY_LO_MASK, 0xC020);
+ else
+ b43_phy_write(dev, B43_PHY_LO_MASK, 0x8020);
+ b43_phy_write(dev, B43_PHY_LO_CTL, 0);
+
+ b43_phy_write(dev, B43_PHY_BASE(0x2B),
+ (b43_phy_read(dev, B43_PHY_BASE(0x2B))
+ & 0xFFC0) | 0x01);
+ b43_phy_write(dev, B43_PHY_BASE(0x2B),
+ (b43_phy_read(dev, B43_PHY_BASE(0x2B))
+ & 0xC0FF) | 0x800);
+
+ b43_phy_write(dev, B43_PHY_RFOVER,
+ b43_phy_read(dev, B43_PHY_RFOVER) | 0x0100);
+ b43_phy_write(dev, B43_PHY_RFOVERVAL,
+ b43_phy_read(dev, B43_PHY_RFOVERVAL) & 0xCFFF);
+
+ if (dev->dev->bus->sprom.r1.boardflags_lo & B43_BFL_EXTLNA) {
+ if (phy->rev >= 7) {
+ b43_phy_write(dev, B43_PHY_RFOVER,
+ b43_phy_read(dev, B43_PHY_RFOVER)
+ | 0x0800);
+ b43_phy_write(dev, B43_PHY_RFOVERVAL,
+ b43_phy_read(dev, B43_PHY_RFOVERVAL)
+ | 0x8000);
+ }
+ }
+ b43_radio_write16(dev, 0x7A, b43_radio_read16(dev, 0x7A)
+ & 0x00F7);
+
+ j = 0;
+ loop_i_max = (phy->radio_rev == 8) ? 15 : 9;
+ for (i = 0; i < loop_i_max; i++) {
+ for (j = 0; j < 16; j++) {
+ b43_radio_write16(dev, 0x43, i);
+ b43_phy_write(dev, B43_PHY_RFOVERVAL,
+ (b43_phy_read(dev, B43_PHY_RFOVERVAL)
+ & 0xF0FF) | (j << 8));
+ b43_phy_write(dev, B43_PHY_PGACTL,
+ (b43_phy_read(dev, B43_PHY_PGACTL)
+ & 0x0FFF) | 0xA000);
+ b43_phy_write(dev, B43_PHY_PGACTL,
+ b43_phy_read(dev, B43_PHY_PGACTL)
+ | 0xF000);
+ udelay(20);
+ if (b43_phy_read(dev, B43_PHY_LO_LEAKAGE) >= 0xDFC)
+ goto exit_loop1;
+ }
+ }
+ exit_loop1:
+ loop1_outer_done = i;
+ loop1_inner_done = j;
+ if (j >= 8) {
+ b43_phy_write(dev, B43_PHY_RFOVERVAL,
+ b43_phy_read(dev, B43_PHY_RFOVERVAL)
+ | 0x30);
+ trsw_rx = 0x1B;
+ for (j = j - 8; j < 16; j++) {
+ b43_phy_write(dev, B43_PHY_RFOVERVAL,
+ (b43_phy_read(dev, B43_PHY_RFOVERVAL)
+ & 0xF0FF) | (j << 8));
+ b43_phy_write(dev, B43_PHY_PGACTL,
+ (b43_phy_read(dev, B43_PHY_PGACTL)
+ & 0x0FFF) | 0xA000);
+ b43_phy_write(dev, B43_PHY_PGACTL,
+ b43_phy_read(dev, B43_PHY_PGACTL)
+ | 0xF000);
+ udelay(20);
+ trsw_rx -= 3;
+ if (b43_phy_read(dev, B43_PHY_LO_LEAKAGE) >= 0xDFC)
+ goto exit_loop2;
+ }
+ } else
+ trsw_rx = 0x18;
+ exit_loop2:
+
+ if (phy->rev != 1) { /* Not in specs, but needed to prevent PPC machine check */
+ b43_phy_write(dev, B43_PHY_ANALOGOVER, backup_phy[4]);
+ b43_phy_write(dev, B43_PHY_ANALOGOVERVAL, backup_phy[5]);
+ }
+ b43_phy_write(dev, B43_PHY_BASE(0x5A), backup_phy[6]);
+ b43_phy_write(dev, B43_PHY_BASE(0x59), backup_phy[7]);
+ b43_phy_write(dev, B43_PHY_BASE(0x58), backup_phy[8]);
+ b43_phy_write(dev, B43_PHY_BASE(0x0A), backup_phy[9]);
+ b43_phy_write(dev, B43_PHY_BASE(0x03), backup_phy[10]);
+ b43_phy_write(dev, B43_PHY_LO_MASK, backup_phy[11]);
+ b43_phy_write(dev, B43_PHY_LO_CTL, backup_phy[12]);
+ b43_phy_write(dev, B43_PHY_BASE(0x2B), backup_phy[13]);
+ b43_phy_write(dev, B43_PHY_PGACTL, backup_phy[14]);
+
+ b43_phy_set_baseband_attenuation(dev, backup_bband);
+
+ b43_radio_write16(dev, 0x52, backup_radio[0]);
+ b43_radio_write16(dev, 0x43, backup_radio[1]);
+ b43_radio_write16(dev, 0x7A, backup_radio[2]);
+
+ b43_phy_write(dev, B43_PHY_RFOVER, backup_phy[2] | 0x0003);
+ udelay(10);
+ b43_phy_write(dev, B43_PHY_RFOVER, backup_phy[2]);
+ b43_phy_write(dev, B43_PHY_RFOVERVAL, backup_phy[3]);
+ b43_phy_write(dev, B43_PHY_CRS0, backup_phy[0]);
+ b43_phy_write(dev, B43_PHY_CCKBBANDCFG, backup_phy[1]);
+
+ phy->max_lb_gain =
+ ((loop1_inner_done * 6) - (loop1_outer_done * 4)) - 11;
+ phy->trsw_rx_gain = trsw_rx * 2;
+}
+
+static void b43_phy_initg(struct b43_wldev *dev)
+{
+ struct b43_phy *phy = &dev->phy;
+ u16 tmp;
+
+ if (phy->rev == 1)
+ b43_phy_initb5(dev);
+ else
+ b43_phy_initb6(dev);
+
+ if (phy->rev >= 2 || phy->gmode)
+ b43_phy_inita(dev);
+
+ if (phy->rev >= 2) {
+ b43_phy_write(dev, B43_PHY_ANALOGOVER, 0);
+ b43_phy_write(dev, B43_PHY_ANALOGOVERVAL, 0);
+ }
+ if (phy->rev == 2) {
+ b43_phy_write(dev, B43_PHY_RFOVER, 0);
+ b43_phy_write(dev, B43_PHY_PGACTL, 0xC0);
+ }
+ if (phy->rev > 5) {
+ b43_phy_write(dev, B43_PHY_RFOVER, 0x400);
+ b43_phy_write(dev, B43_PHY_PGACTL, 0xC0);
+ }
+ if (phy->gmode || phy->rev >= 2) {
+ tmp = b43_phy_read(dev, B43_PHY_VERSION_OFDM);
+ tmp &= B43_PHYVER_VERSION;
+ if (tmp == 3 || tmp == 5) {
+ b43_phy_write(dev, B43_PHY_OFDM(0xC2), 0x1816);
+ b43_phy_write(dev, B43_PHY_OFDM(0xC3), 0x8006);
+ }
+ if (tmp == 5) {
+ b43_phy_write(dev, B43_PHY_OFDM(0xCC),
+ (b43_phy_read(dev, B43_PHY_OFDM(0xCC))
+ & 0x00FF) | 0x1F00);
+ }
+ }
+ if ((phy->rev <= 2 && phy->gmode) || phy->rev >= 2)
+ b43_phy_write(dev, B43_PHY_OFDM(0x7E), 0x78);
+ if (phy->radio_rev == 8) {
+ b43_phy_write(dev, B43_PHY_EXTG(0x01),
+ b43_phy_read(dev, B43_PHY_EXTG(0x01))
+ | 0x80);
+ b43_phy_write(dev, B43_PHY_OFDM(0x3E),
+ b43_phy_read(dev, B43_PHY_OFDM(0x3E))
+ | 0x4);
+ }
+ if (has_loopback_gain(phy))
+ b43_calc_loopback_gain(dev);
+
+ if (phy->radio_rev != 8) {
+ if (phy->initval == 0xFFFF)
+ phy->initval = b43_radio_init2050(dev);
+ else
+ b43_radio_write16(dev, 0x0078, phy->initval);
+ }
+ if (phy->lo_control->tx_bias == 0xFF) {
+ b43_lo_g_measure(dev);
+ } else {
+ if (has_tx_magnification(phy)) {
+ b43_radio_write16(dev, 0x52,
+ (b43_radio_read16(dev, 0x52) & 0xFF00)
+ | phy->lo_control->tx_bias | phy->
+ lo_control->tx_magn);
+ } else {
+ b43_radio_write16(dev, 0x52,
+ (b43_radio_read16(dev, 0x52) & 0xFFF0)
+ | phy->lo_control->tx_bias);
+ }
+ if (phy->rev >= 6) {
+ b43_phy_write(dev, B43_PHY_BASE(0x36),
+ (b43_phy_read(dev, B43_PHY_BASE(0x36))
+ & 0x0FFF) | (phy->lo_control->
+ tx_bias << 12));
+ }
+ if (dev->dev->bus->sprom.r1.boardflags_lo & B43_BFL_PACTRL)
+ b43_phy_write(dev, B43_PHY_BASE(0x2E), 0x8075);
+ else
+ b43_phy_write(dev, B43_PHY_BASE(0x2E), 0x807F);
+ if (phy->rev < 2)
+ b43_phy_write(dev, B43_PHY_BASE(0x2F), 0x101);
+ else
+ b43_phy_write(dev, B43_PHY_BASE(0x2F), 0x202);
+ }
+ if (phy->gmode || phy->rev >= 2) {
+ b43_lo_g_adjust(dev);
+ b43_phy_write(dev, B43_PHY_LO_MASK, 0x8078);
+ }
+
+ if (!(dev->dev->bus->sprom.r1.boardflags_lo & B43_BFL_RSSI)) {
+ /* The specs state to update the NRSSI LT with
+ * the value 0x7FFFFFFF here. I think that is some weird
+ * compiler optimization in the original driver.
+ * Essentially, what we do here is resetting all NRSSI LT
+ * entries to -32 (see the limit_value() in nrssi_hw_update())
+ */
+ b43_nrssi_hw_update(dev, 0xFFFF); //FIXME?
+ b43_calc_nrssi_threshold(dev);
+ } else if (phy->gmode || phy->rev >= 2) {
+ if (phy->nrssi[0] == -1000) {
+ B43_WARN_ON(phy->nrssi[1] != -1000);
+ b43_calc_nrssi_slope(dev);
+ } else
+ b43_calc_nrssi_threshold(dev);
+ }
+ if (phy->radio_rev == 8)
+ b43_phy_write(dev, B43_PHY_EXTG(0x05), 0x3230);
+ b43_phy_init_pctl(dev);
+ /* FIXME: The spec says in the following if, the 0 should be replaced
+ 'if OFDM may not be used in the current locale'
+ but OFDM is legal everywhere */
+ if ((dev->dev->bus->chip_id == 0x4306
+ && dev->dev->bus->chip_package == 2) || 0) {
+ b43_phy_write(dev, B43_PHY_CRS0, b43_phy_read(dev, B43_PHY_CRS0)
+ & 0xBFFF);
+ b43_phy_write(dev, B43_PHY_OFDM(0xC3),
+ b43_phy_read(dev, B43_PHY_OFDM(0xC3))
+ & 0x7FFF);
+ }
+}
+
+/* Set the baseband attenuation value on chip. */
+void b43_phy_set_baseband_attenuation(struct b43_wldev *dev,
+ u16 baseband_attenuation)
+{
+ struct b43_phy *phy = &dev->phy;
+
+ if (phy->analog == 0) {
+ b43_write16(dev, B43_MMIO_PHY0, (b43_read16(dev, B43_MMIO_PHY0)
+ & 0xFFF0) |
+ baseband_attenuation);
+ } else if (phy->analog > 1) {
+ b43_phy_write(dev, B43_PHY_DACCTL,
+ (b43_phy_read(dev, B43_PHY_DACCTL)
+ & 0xFFC3) | (baseband_attenuation << 2));
+ } else {
+ b43_phy_write(dev, B43_PHY_DACCTL,
+ (b43_phy_read(dev, B43_PHY_DACCTL)
+ & 0xFF87) | (baseband_attenuation << 3));
+ }
+}
+
+/* http://bcm-specs.sipsolutions.net/EstimatePowerOut
+ * This function converts a TSSI value to dBm in Q5.2
+ */
+static s8 b43_phy_estimate_power_out(struct b43_wldev *dev, s8 tssi)
+{
+ struct b43_phy *phy = &dev->phy;
+ s8 dbm = 0;
+ s32 tmp;
+
+ tmp = (phy->tgt_idle_tssi - phy->cur_idle_tssi + tssi);
+
+ switch (phy->type) {
+ case B43_PHYTYPE_A:
+ tmp += 0x80;
+ tmp = limit_value(tmp, 0x00, 0xFF);
+ dbm = phy->tssi2dbm[tmp];
+ //TODO: There's a FIXME on the specs
+ break;
+ case B43_PHYTYPE_B:
+ case B43_PHYTYPE_G:
+ tmp = limit_value(tmp, 0x00, 0x3F);
+ dbm = phy->tssi2dbm[tmp];
+ break;
+ default:
+ B43_WARN_ON(1);
+ }
+
+ return dbm;
+}
+
+void b43_put_attenuation_into_ranges(struct b43_wldev *dev,
+ int *_bbatt, int *_rfatt)
+{
+ int rfatt = *_rfatt;
+ int bbatt = *_bbatt;
+ struct b43_txpower_lo_control *lo = dev->phy.lo_control;
+
+ /* Get baseband and radio attenuation values into their permitted ranges.
+ * Radio attenuation affects power level 4 times as much as baseband. */
+
+ /* Range constants */
+ const int rf_min = lo->rfatt_list.min_val;
+ const int rf_max = lo->rfatt_list.max_val;
+ const int bb_min = lo->bbatt_list.min_val;
+ const int bb_max = lo->bbatt_list.max_val;
+
+ while (1) {
+ if (rfatt > rf_max && bbatt > bb_max - 4)
+ break; /* Can not get it into ranges */
+ if (rfatt < rf_min && bbatt < bb_min + 4)
+ break; /* Can not get it into ranges */
+ if (bbatt > bb_max && rfatt > rf_max - 1)
+ break; /* Can not get it into ranges */
+ if (bbatt < bb_min && rfatt < rf_min + 1)
+ break; /* Can not get it into ranges */
+
+ if (bbatt > bb_max) {
+ bbatt -= 4;
+ rfatt += 1;
+ continue;
+ }
+ if (bbatt < bb_min) {
+ bbatt += 4;
+ rfatt -= 1;
+ continue;
+ }
+ if (rfatt > rf_max) {
+ rfatt -= 1;
+ bbatt += 4;
+ continue;
+ }
+ if (rfatt < rf_min) {
+ rfatt += 1;
+ bbatt -= 4;
+ continue;
+ }
+ break;
+ }
+
+ *_rfatt = limit_value(rfatt, rf_min, rf_max);
+ *_bbatt = limit_value(bbatt, bb_min, bb_max);
+}
+
+/* http://bcm-specs.sipsolutions.net/RecalculateTransmissionPower */
+void b43_phy_xmitpower(struct b43_wldev *dev)
+{
+ struct ssb_bus *bus = dev->dev->bus;
+ struct b43_phy *phy = &dev->phy;
+
+ if (phy->cur_idle_tssi == 0)
+ return;
+ if ((bus->boardinfo.vendor == SSB_BOARDVENDOR_BCM) &&
+ (bus->boardinfo.type == SSB_BOARD_BU4306))
+ return;
+#ifdef CONFIG_B43_DEBUG
+ if (phy->manual_txpower_control)
+ return;
+#endif
+
+ switch (phy->type) {
+ case B43_PHYTYPE_A:{
+
+ //TODO: Nothing for A PHYs yet :-/
+
+ break;
+ }
+ case B43_PHYTYPE_B:
+ case B43_PHYTYPE_G:{
+ u16 tmp;
+ s8 v0, v1, v2, v3;
+ s8 average;
+ int max_pwr;
+ int desired_pwr, estimated_pwr, pwr_adjust;
+ int rfatt_delta, bbatt_delta;
+ int rfatt, bbatt;
+ u8 tx_control;
+ unsigned long phylock_flags;
+
+ tmp = b43_shm_read16(dev, B43_SHM_SHARED, 0x0058);
+ v0 = (s8) (tmp & 0x00FF);
+ v1 = (s8) ((tmp & 0xFF00) >> 8);
+ tmp = b43_shm_read16(dev, B43_SHM_SHARED, 0x005A);
+ v2 = (s8) (tmp & 0x00FF);
+ v3 = (s8) ((tmp & 0xFF00) >> 8);
+ tmp = 0;
+
+ if (v0 == 0x7F || v1 == 0x7F || v2 == 0x7F
+ || v3 == 0x7F) {
+ tmp =
+ b43_shm_read16(dev, B43_SHM_SHARED, 0x0070);
+ v0 = (s8) (tmp & 0x00FF);
+ v1 = (s8) ((tmp & 0xFF00) >> 8);
+ tmp =
+ b43_shm_read16(dev, B43_SHM_SHARED, 0x0072);
+ v2 = (s8) (tmp & 0x00FF);
+ v3 = (s8) ((tmp & 0xFF00) >> 8);
+ if (v0 == 0x7F || v1 == 0x7F || v2 == 0x7F
+ || v3 == 0x7F)
+ return;
+ v0 = (v0 + 0x20) & 0x3F;
+ v1 = (v1 + 0x20) & 0x3F;
+ v2 = (v2 + 0x20) & 0x3F;
+ v3 = (v3 + 0x20) & 0x3F;
+ tmp = 1;
+ }
+ b43_shm_clear_tssi(dev);
+
+ average = (v0 + v1 + v2 + v3 + 2) / 4;
+
+ if (tmp
+ && (b43_shm_read16(dev, B43_SHM_SHARED, 0x005E) &
+ 0x8))
+ average -= 13;
+
+ estimated_pwr =
+ b43_phy_estimate_power_out(dev, average);
+
+ max_pwr = dev->dev->bus->sprom.r1.maxpwr_bg;
+ if ((dev->dev->bus->sprom.r1.
+ boardflags_lo & B43_BFL_PACTRL)
+ && (phy->type == B43_PHYTYPE_G))
+ max_pwr -= 0x3;
+ if (unlikely(max_pwr <= 0)) {
+ b43warn(dev->wl,
+ "Invalid max-TX-power value in SPROM.\n");
+ max_pwr = 60; /* fake it */
+ dev->dev->bus->sprom.r1.maxpwr_bg = max_pwr;
+ }
+
+ /*TODO:
+ max_pwr = min(REG - dev->dev->bus->sprom.antennagain_bgphy - 0x6, max_pwr)
+ where REG is the max power as per the regulatory domain
+ */
+
+ /* Get desired power (in Q5.2) */
+ desired_pwr = INT_TO_Q52(phy->power_level);
+ /* And limit it. max_pwr already is Q5.2 */
+ desired_pwr = limit_value(desired_pwr, 0, max_pwr);
+ if (b43_debug(dev, B43_DBG_XMITPOWER)) {
+ b43dbg(dev->wl,
+ "Current TX power output: " Q52_FMT
+ " dBm, " "Desired TX power output: "
+ Q52_FMT " dBm\n", Q52_ARG(estimated_pwr),
+ Q52_ARG(desired_pwr));
+ }
+
+ /* Calculate the adjustment delta. */
+ pwr_adjust = desired_pwr - estimated_pwr;
+
+ /* RF attenuation delta. */
+ rfatt_delta = ((pwr_adjust + 7) / 8);
+ /* Lower attenuation => Bigger power output. Negate it. */
+ rfatt_delta = -rfatt_delta;
+
+ /* Baseband attenuation delta. */
+ bbatt_delta = pwr_adjust / 2;
+ /* Lower attenuation => Bigger power output. Negate it. */
+ bbatt_delta = -bbatt_delta;
+ /* RF att affects power level 4 times as much as
+ * Baseband attennuation. Subtract it. */
+ bbatt_delta -= 4 * rfatt_delta;
+
+ /* So do we finally need to adjust something? */
+ if ((rfatt_delta == 0) && (bbatt_delta == 0)) {
+ b43_lo_g_ctl_mark_cur_used(dev);
+ return;
+ }
+
+ /* Calculate the new attenuation values. */
+ bbatt = phy->bbatt.att;
+ bbatt += bbatt_delta;
+ rfatt = phy->rfatt.att;
+ rfatt += rfatt_delta;
+
+ b43_put_attenuation_into_ranges(dev, &bbatt, &rfatt);
+ tx_control = phy->tx_control;
+ if ((phy->radio_ver == 0x2050) && (phy->radio_rev == 2)) {
+ if (rfatt <= 1) {
+ if (tx_control == 0) {
+ tx_control =
+ B43_TXCTL_PA2DB |
+ B43_TXCTL_TXMIX;
+ rfatt += 2;
+ bbatt += 2;
+ } else if (dev->dev->bus->sprom.r1.
+ boardflags_lo &
+ B43_BFL_PACTRL) {
+ bbatt += 4 * (rfatt - 2);
+ rfatt = 2;
+ }
+ } else if (rfatt > 4 && tx_control) {
+ tx_control = 0;
+ if (bbatt < 3) {
+ rfatt -= 3;
+ bbatt += 2;
+ } else {
+ rfatt -= 2;
+ bbatt -= 2;
+ }
+ }
+ }
+ /* Save the control values */
+ phy->tx_control = tx_control;
+ b43_put_attenuation_into_ranges(dev, &bbatt, &rfatt);
+ phy->rfatt.att = rfatt;
+ phy->bbatt.att = bbatt;
+
+ /* Adjust the hardware */
+ b43_phy_lock(dev, phylock_flags);
+ b43_radio_lock(dev);
+ b43_set_txpower_g(dev, &phy->bbatt, &phy->rfatt,
+ phy->tx_control);
+ b43_lo_g_ctl_mark_cur_used(dev);
+ b43_radio_unlock(dev);
+ b43_phy_unlock(dev, phylock_flags);
+ break;
+ }
+ default:
+ B43_WARN_ON(1);
+ }
+}
+
+static inline s32 b43_tssi2dbm_ad(s32 num, s32 den)
+{
+ if (num < 0)
+ return num / den;
+ else
+ return (num + den / 2) / den;
+}
+
+static inline
+ s8 b43_tssi2dbm_entry(s8 entry[], u8 index, s16 pab0, s16 pab1, s16 pab2)
+{
+ s32 m1, m2, f = 256, q, delta;
+ s8 i = 0;
+
+ m1 = b43_tssi2dbm_ad(16 * pab0 + index * pab1, 32);
+ m2 = max(b43_tssi2dbm_ad(32768 + index * pab2, 256), 1);
+ do {
+ if (i > 15)
+ return -EINVAL;
+ q = b43_tssi2dbm_ad(f * 4096 -
+ b43_tssi2dbm_ad(m2 * f, 16) * f, 2048);
+ delta = abs(q - f);
+ f = q;
+ i++;
+ } while (delta >= 2);
+ entry[index] = limit_value(b43_tssi2dbm_ad(m1 * f, 8192), -127, 128);
+ return 0;
+}
+
+/* http://bcm-specs.sipsolutions.net/TSSI_to_DBM_Table */
+int b43_phy_init_tssi2dbm_table(struct b43_wldev *dev)
+{
+ struct b43_phy *phy = &dev->phy;
+ s16 pab0, pab1, pab2;
+ u8 idx;
+ s8 *dyn_tssi2dbm;
+
+ if (phy->type == B43_PHYTYPE_A) {
+ pab0 = (s16) (dev->dev->bus->sprom.r1.pa1b0);
+ pab1 = (s16) (dev->dev->bus->sprom.r1.pa1b1);
+ pab2 = (s16) (dev->dev->bus->sprom.r1.pa1b2);
+ } else {
+ pab0 = (s16) (dev->dev->bus->sprom.r1.pa0b0);
+ pab1 = (s16) (dev->dev->bus->sprom.r1.pa0b1);
+ pab2 = (s16) (dev->dev->bus->sprom.r1.pa0b2);
+ }
+
+ if ((dev->dev->bus->chip_id == 0x4301) && (phy->radio_ver != 0x2050)) {
+ phy->tgt_idle_tssi = 0x34;
+ phy->tssi2dbm = b43_tssi2dbm_b_table;
+ return 0;
+ }
+
+ if (pab0 != 0 && pab1 != 0 && pab2 != 0 &&
+ pab0 != -1 && pab1 != -1 && pab2 != -1) {
+ /* The pabX values are set in SPROM. Use them. */
+ if (phy->type == B43_PHYTYPE_A) {
+ if ((s8) dev->dev->bus->sprom.r1.itssi_a != 0 &&
+ (s8) dev->dev->bus->sprom.r1.itssi_a != -1)
+ phy->tgt_idle_tssi =
+ (s8) (dev->dev->bus->sprom.r1.itssi_a);
+ else
+ phy->tgt_idle_tssi = 62;
+ } else {
+ if ((s8) dev->dev->bus->sprom.r1.itssi_bg != 0 &&
+ (s8) dev->dev->bus->sprom.r1.itssi_bg != -1)
+ phy->tgt_idle_tssi =
+ (s8) (dev->dev->bus->sprom.r1.itssi_bg);
+ else
+ phy->tgt_idle_tssi = 62;
+ }
+ dyn_tssi2dbm = kmalloc(64, GFP_KERNEL);
+ if (dyn_tssi2dbm == NULL) {
+ b43err(dev->wl, "Could not allocate memory"
+ "for tssi2dbm table\n");
+ return -ENOMEM;
+ }
+ for (idx = 0; idx < 64; idx++)
+ if (b43_tssi2dbm_entry
+ (dyn_tssi2dbm, idx, pab0, pab1, pab2)) {
+ phy->tssi2dbm = NULL;
+ b43err(dev->wl, "Could not generate "
+ "tssi2dBm table\n");
+ kfree(dyn_tssi2dbm);
+ return -ENODEV;
+ }
+ phy->tssi2dbm = dyn_tssi2dbm;
+ phy->dyn_tssi_tbl = 1;
+ } else {
+ /* pabX values not set in SPROM. */
+ switch (phy->type) {
+ case B43_PHYTYPE_A:
+ /* APHY needs a generated table. */
+ phy->tssi2dbm = NULL;
+ b43err(dev->wl, "Could not generate tssi2dBm "
+ "table (wrong SPROM info)!\n");
+ return -ENODEV;
+ case B43_PHYTYPE_B:
+ phy->tgt_idle_tssi = 0x34;
+ phy->tssi2dbm = b43_tssi2dbm_b_table;
+ break;
+ case B43_PHYTYPE_G:
+ phy->tgt_idle_tssi = 0x34;
+ phy->tssi2dbm = b43_tssi2dbm_g_table;
+ break;
+ }
+ }
+
+ return 0;
+}
+
+int b43_phy_init(struct b43_wldev *dev)
+{
+ struct b43_phy *phy = &dev->phy;
+ int err = -ENODEV;
+
+ switch (phy->type) {
+ case B43_PHYTYPE_A:
+ if (phy->rev == 2 || phy->rev == 3) {
+ b43_phy_inita(dev);
+ err = 0;
+ }
+ break;
+ case B43_PHYTYPE_B:
+ switch (phy->rev) {
+ case 2:
+ b43_phy_initb2(dev);
+ err = 0;
+ break;
+ case 4:
+ b43_phy_initb4(dev);
+ err = 0;
+ break;
+ case 5:
+ b43_phy_initb5(dev);
+ err = 0;
+ break;
+ case 6:
+ b43_phy_initb6(dev);
+ err = 0;
+ break;
+ }
+ break;
+ case B43_PHYTYPE_G:
+ b43_phy_initg(dev);
+ err = 0;
+ break;
+ }
+ if (err)
+ b43err(dev->wl, "Unknown PHYTYPE found\n");
+
+ return err;
+}
+
+void b43_set_rx_antenna(struct b43_wldev *dev, int antenna)
+{
+ struct b43_phy *phy = &dev->phy;
+ u32 hf;
+ u16 tmp;
+ int autodiv = 0;
+
+ if (antenna == B43_ANTENNA_AUTO0 || antenna == B43_ANTENNA_AUTO1)
+ autodiv = 1;
+
+ hf = b43_hf_read(dev);
+ hf &= ~B43_HF_ANTDIVHELP;
+ b43_hf_write(dev, hf);
+
+ switch (phy->type) {
+ case B43_PHYTYPE_A:
+ case B43_PHYTYPE_G:
+ tmp = b43_phy_read(dev, B43_PHY_BBANDCFG);
+ tmp &= ~B43_PHY_BBANDCFG_RXANT;
+ tmp |= (autodiv ? B43_ANTENNA_AUTO0 : antenna)
+ << B43_PHY_BBANDCFG_RXANT_SHIFT;
+ b43_phy_write(dev, B43_PHY_BBANDCFG, tmp);
+
+ if (autodiv) {
+ tmp = b43_phy_read(dev, B43_PHY_ANTDWELL);
+ if (antenna == B43_ANTENNA_AUTO0)
+ tmp &= ~B43_PHY_ANTDWELL_AUTODIV1;
+ else
+ tmp |= B43_PHY_ANTDWELL_AUTODIV1;
+ b43_phy_write(dev, B43_PHY_ANTDWELL, tmp);
+ }
+ if (phy->type == B43_PHYTYPE_G) {
+ tmp = b43_phy_read(dev, B43_PHY_ANTWRSETT);
+ if (autodiv)
+ tmp |= B43_PHY_ANTWRSETT_ARXDIV;
+ else
+ tmp &= ~B43_PHY_ANTWRSETT_ARXDIV;
+ b43_phy_write(dev, B43_PHY_ANTWRSETT, tmp);
+ if (phy->rev >= 2) {
+ tmp = b43_phy_read(dev, B43_PHY_OFDM61);
+ tmp |= B43_PHY_OFDM61_10;
+ b43_phy_write(dev, B43_PHY_OFDM61, tmp);
+
+ tmp =
+ b43_phy_read(dev, B43_PHY_DIVSRCHGAINBACK);
+ tmp = (tmp & 0xFF00) | 0x15;
+ b43_phy_write(dev, B43_PHY_DIVSRCHGAINBACK,
+ tmp);
+
+ if (phy->rev == 2) {
+ b43_phy_write(dev, B43_PHY_ADIVRELATED,
+ 8);
+ } else {
+ tmp =
+ b43_phy_read(dev,
+ B43_PHY_ADIVRELATED);
+ tmp = (tmp & 0xFF00) | 8;
+ b43_phy_write(dev, B43_PHY_ADIVRELATED,
+ tmp);
+ }
+ }
+ if (phy->rev >= 6)
+ b43_phy_write(dev, B43_PHY_OFDM9B, 0xDC);
+ } else {
+ if (phy->rev < 3) {
+ tmp = b43_phy_read(dev, B43_PHY_ANTDWELL);
+ tmp = (tmp & 0xFF00) | 0x24;
+ b43_phy_write(dev, B43_PHY_ANTDWELL, tmp);
+ } else {
+ tmp = b43_phy_read(dev, B43_PHY_OFDM61);
+ tmp |= 0x10;
+ b43_phy_write(dev, B43_PHY_OFDM61, tmp);
+ if (phy->analog == 3) {
+ b43_phy_write(dev, B43_PHY_CLIPPWRDOWNT,
+ 0x1D);
+ b43_phy_write(dev, B43_PHY_ADIVRELATED,
+ 8);
+ } else {
+ b43_phy_write(dev, B43_PHY_CLIPPWRDOWNT,
+ 0x3A);
+ tmp =
+ b43_phy_read(dev,
+ B43_PHY_ADIVRELATED);
+ tmp = (tmp & 0xFF00) | 8;
+ b43_phy_write(dev, B43_PHY_ADIVRELATED,
+ tmp);
+ }
+ }
+ }
+ break;
+ case B43_PHYTYPE_B:
+ tmp = b43_phy_read(dev, B43_PHY_CCKBBANDCFG);
+ tmp &= ~B43_PHY_BBANDCFG_RXANT;
+ tmp |= (autodiv ? B43_ANTENNA_AUTO0 : antenna)
+ << B43_PHY_BBANDCFG_RXANT_SHIFT;
+ b43_phy_write(dev, B43_PHY_CCKBBANDCFG, tmp);
+ break;
+ default:
+ B43_WARN_ON(1);
+ }
+
+ hf |= B43_HF_ANTDIVHELP;
+ b43_hf_write(dev, hf);
+}
+
+/* Get the freq, as it has to be written to the device. */
+static inline u16 channel2freq_bg(u8 channel)
+{
+ B43_WARN_ON(!(channel >= 1 && channel <= 14));
+
+ return b43_radio_channel_codes_bg[channel - 1];
+}
+
+/* Get the freq, as it has to be written to the device. */
+static inline u16 channel2freq_a(u8 channel)
+{
+ B43_WARN_ON(channel > 200);
+
+ return (5000 + 5 * channel);
+}
+
+void b43_radio_lock(struct b43_wldev *dev)
+{
+ u32 macctl;
+
+ macctl = b43_read32(dev, B43_MMIO_MACCTL);
+ macctl |= B43_MACCTL_RADIOLOCK;
+ b43_write32(dev, B43_MMIO_MACCTL, macctl);
+ /* Commit the write and wait for the device
+ * to exit any radio register access. */
+ b43_read32(dev, B43_MMIO_MACCTL);
+ udelay(10);
+}
+
+void b43_radio_unlock(struct b43_wldev *dev)
+{
+ u32 macctl;
+
+ /* Commit any write */
+ b43_read16(dev, B43_MMIO_PHY_VER);
+ /* unlock */
+ macctl = b43_read32(dev, B43_MMIO_MACCTL);
+ macctl &= ~B43_MACCTL_RADIOLOCK;
+ b43_write32(dev, B43_MMIO_MACCTL, macctl);
+}
+
+u16 b43_radio_read16(struct b43_wldev *dev, u16 offset)
+{
+ struct b43_phy *phy = &dev->phy;
+
+ switch (phy->type) {
+ case B43_PHYTYPE_A:
+ offset |= 0x0040;
+ break;
+ case B43_PHYTYPE_B:
+ if (phy->radio_ver == 0x2053) {
+ if (offset < 0x70)
+ offset += 0x80;
+ else if (offset < 0x80)
+ offset += 0x70;
+ } else if (phy->radio_ver == 0x2050) {
+ offset |= 0x80;
+ } else
+ B43_WARN_ON(1);
+ break;
+ case B43_PHYTYPE_G:
+ offset |= 0x80;
+ break;
+ }
+
+ b43_write16(dev, B43_MMIO_RADIO_CONTROL, offset);
+ return b43_read16(dev, B43_MMIO_RADIO_DATA_LOW);
+}
+
+void b43_radio_write16(struct b43_wldev *dev, u16 offset, u16 val)
+{
+ b43_write16(dev, B43_MMIO_RADIO_CONTROL, offset);
+ mmiowb();
+ b43_write16(dev, B43_MMIO_RADIO_DATA_LOW, val);
+}
+
+static void b43_set_all_gains(struct b43_wldev *dev,
+ s16 first, s16 second, s16 third)
+{
+ struct b43_phy *phy = &dev->phy;
+ u16 i;
+ u16 start = 0x08, end = 0x18;
+ u16 tmp;
+ u16 table;
+
+ if (phy->rev <= 1) {
+ start = 0x10;
+ end = 0x20;
+ }
+
+ table = B43_OFDMTAB_GAINX;
+ if (phy->rev <= 1)
+ table = B43_OFDMTAB_GAINX_R1;
+ for (i = 0; i < 4; i++)
+ b43_ofdmtab_write16(dev, table, i, first);
+
+ for (i = start; i < end; i++)
+ b43_ofdmtab_write16(dev, table, i, second);
+
+ if (third != -1) {
+ tmp = ((u16) third << 14) | ((u16) third << 6);
+ b43_phy_write(dev, 0x04A0,
+ (b43_phy_read(dev, 0x04A0) & 0xBFBF) | tmp);
+ b43_phy_write(dev, 0x04A1,
+ (b43_phy_read(dev, 0x04A1) & 0xBFBF) | tmp);
+ b43_phy_write(dev, 0x04A2,
+ (b43_phy_read(dev, 0x04A2) & 0xBFBF) | tmp);
+ }
+ b43_dummy_transmission(dev);
+}
+
+static void b43_set_original_gains(struct b43_wldev *dev)
+{
+ struct b43_phy *phy = &dev->phy;
+ u16 i, tmp;
+ u16 table;
+ u16 start = 0x0008, end = 0x0018;
+
+ if (phy->rev <= 1) {
+ start = 0x0010;
+ end = 0x0020;
+ }
+
+ table = B43_OFDMTAB_GAINX;
+ if (phy->rev <= 1)
+ table = B43_OFDMTAB_GAINX_R1;
+ for (i = 0; i < 4; i++) {
+ tmp = (i & 0xFFFC);
+ tmp |= (i & 0x0001) << 1;
+ tmp |= (i & 0x0002) >> 1;
+
+ b43_ofdmtab_write16(dev, table, i, tmp);
+ }
+
+ for (i = start; i < end; i++)
+ b43_ofdmtab_write16(dev, table, i, i - start);
+
+ b43_phy_write(dev, 0x04A0,
+ (b43_phy_read(dev, 0x04A0) & 0xBFBF) | 0x4040);
+ b43_phy_write(dev, 0x04A1,
+ (b43_phy_read(dev, 0x04A1) & 0xBFBF) | 0x4040);
+ b43_phy_write(dev, 0x04A2,
+ (b43_phy_read(dev, 0x04A2) & 0xBFBF) | 0x4000);
+ b43_dummy_transmission(dev);
+}
+
+/* Synthetic PU workaround */
+static void b43_synth_pu_workaround(struct b43_wldev *dev, u8 channel)
+{
+ struct b43_phy *phy = &dev->phy;
+
+ might_sleep();
+
+ if (phy->radio_ver != 0x2050 || phy->radio_rev >= 6) {
+ /* We do not need the workaround. */
+ return;
+ }
+
+ if (channel <= 10) {
+ b43_write16(dev, B43_MMIO_CHANNEL,
+ channel2freq_bg(channel + 4));
+ } else {
+ b43_write16(dev, B43_MMIO_CHANNEL, channel2freq_bg(1));
+ }
+ msleep(1);
+ b43_write16(dev, B43_MMIO_CHANNEL, channel2freq_bg(channel));
+}
+
+u8 b43_radio_aci_detect(struct b43_wldev *dev, u8 channel)
+{
+ struct b43_phy *phy = &dev->phy;
+ u8 ret = 0;
+ u16 saved, rssi, temp;
+ int i, j = 0;
+
+ saved = b43_phy_read(dev, 0x0403);
+ b43_radio_selectchannel(dev, channel, 0);
+ b43_phy_write(dev, 0x0403, (saved & 0xFFF8) | 5);
+ if (phy->aci_hw_rssi)
+ rssi = b43_phy_read(dev, 0x048A) & 0x3F;
+ else
+ rssi = saved & 0x3F;
+ /* clamp temp to signed 5bit */
+ if (rssi > 32)
+ rssi -= 64;
+ for (i = 0; i < 100; i++) {
+ temp = (b43_phy_read(dev, 0x047F) >> 8) & 0x3F;
+ if (temp > 32)
+ temp -= 64;
+ if (temp < rssi)
+ j++;
+ if (j >= 20)
+ ret = 1;
+ }
+ b43_phy_write(dev, 0x0403, saved);
+
+ return ret;
+}
+
+u8 b43_radio_aci_scan(struct b43_wldev * dev)
+{
+ struct b43_phy *phy = &dev->phy;
+ u8 ret[13];
+ unsigned int channel = phy->channel;
+ unsigned int i, j, start, end;
+ unsigned long phylock_flags;
+
+ if (!((phy->type == B43_PHYTYPE_G) && (phy->rev > 0)))
+ return 0;
+
+ b43_phy_lock(dev, phylock_flags);
+ b43_radio_lock(dev);
+ b43_phy_write(dev, 0x0802, b43_phy_read(dev, 0x0802) & 0xFFFC);
+ b43_phy_write(dev, B43_PHY_G_CRS,
+ b43_phy_read(dev, B43_PHY_G_CRS) & 0x7FFF);
+ b43_set_all_gains(dev, 3, 8, 1);
+
+ start = (channel - 5 > 0) ? channel - 5 : 1;
+ end = (channel + 5 < 14) ? channel + 5 : 13;
+
+ for (i = start; i <= end; i++) {
+ if (abs(channel - i) > 2)
+ ret[i - 1] = b43_radio_aci_detect(dev, i);
+ }
+ b43_radio_selectchannel(dev, channel, 0);
+ b43_phy_write(dev, 0x0802,
+ (b43_phy_read(dev, 0x0802) & 0xFFFC) | 0x0003);
+ b43_phy_write(dev, 0x0403, b43_phy_read(dev, 0x0403) & 0xFFF8);
+ b43_phy_write(dev, B43_PHY_G_CRS,
+ b43_phy_read(dev, B43_PHY_G_CRS) | 0x8000);
+ b43_set_original_gains(dev);
+ for (i = 0; i < 13; i++) {
+ if (!ret[i])
+ continue;
+ end = (i + 5 < 13) ? i + 5 : 13;
+ for (j = i; j < end; j++)
+ ret[j] = 1;
+ }
+ b43_radio_unlock(dev);
+ b43_phy_unlock(dev, phylock_flags);
+
+ return ret[channel - 1];
+}
+
+/* http://bcm-specs.sipsolutions.net/NRSSILookupTable */
+void b43_nrssi_hw_write(struct b43_wldev *dev, u16 offset, s16 val)
+{
+ b43_phy_write(dev, B43_PHY_NRSSILT_CTRL, offset);
+ mmiowb();
+ b43_phy_write(dev, B43_PHY_NRSSILT_DATA, (u16) val);
+}
+
+/* http://bcm-specs.sipsolutions.net/NRSSILookupTable */
+s16 b43_nrssi_hw_read(struct b43_wldev *dev, u16 offset)
+{
+ u16 val;
+
+ b43_phy_write(dev, B43_PHY_NRSSILT_CTRL, offset);
+ val = b43_phy_read(dev, B43_PHY_NRSSILT_DATA);
+
+ return (s16) val;
+}
+
+/* http://bcm-specs.sipsolutions.net/NRSSILookupTable */
+void b43_nrssi_hw_update(struct b43_wldev *dev, u16 val)
+{
+ u16 i;
+ s16 tmp;
+
+ for (i = 0; i < 64; i++) {
+ tmp = b43_nrssi_hw_read(dev, i);
+ tmp -= val;
+ tmp = limit_value(tmp, -32, 31);
+ b43_nrssi_hw_write(dev, i, tmp);
+ }
+}
+
+/* http://bcm-specs.sipsolutions.net/NRSSILookupTable */
+void b43_nrssi_mem_update(struct b43_wldev *dev)
+{
+ struct b43_phy *phy = &dev->phy;
+ s16 i, delta;
+ s32 tmp;
+
+ delta = 0x1F - phy->nrssi[0];
+ for (i = 0; i < 64; i++) {
+ tmp = (i - delta) * phy->nrssislope;
+ tmp /= 0x10000;
+ tmp += 0x3A;
+ tmp = limit_value(tmp, 0, 0x3F);
+ phy->nrssi_lt[i] = tmp;
+ }
+}
+
+static void b43_calc_nrssi_offset(struct b43_wldev *dev)
+{
+ struct b43_phy *phy = &dev->phy;
+ u16 backup[20] = { 0 };
+ s16 v47F;
+ u16 i;
+ u16 saved = 0xFFFF;
+
+ backup[0] = b43_phy_read(dev, 0x0001);
+ backup[1] = b43_phy_read(dev, 0x0811);
+ backup[2] = b43_phy_read(dev, 0x0812);
+ if (phy->rev != 1) { /* Not in specs, but needed to prevent PPC machine check */
+ backup[3] = b43_phy_read(dev, 0x0814);
+ backup[4] = b43_phy_read(dev, 0x0815);
+ }
+ backup[5] = b43_phy_read(dev, 0x005A);
+ backup[6] = b43_phy_read(dev, 0x0059);
+ backup[7] = b43_phy_read(dev, 0x0058);
+ backup[8] = b43_phy_read(dev, 0x000A);
+ backup[9] = b43_phy_read(dev, 0x0003);
+ backup[10] = b43_radio_read16(dev, 0x007A);
+ backup[11] = b43_radio_read16(dev, 0x0043);
+
+ b43_phy_write(dev, 0x0429, b43_phy_read(dev, 0x0429) & 0x7FFF);
+ b43_phy_write(dev, 0x0001,
+ (b43_phy_read(dev, 0x0001) & 0x3FFF) | 0x4000);
+ b43_phy_write(dev, 0x0811, b43_phy_read(dev, 0x0811) | 0x000C);
+ b43_phy_write(dev, 0x0812,
+ (b43_phy_read(dev, 0x0812) & 0xFFF3) | 0x0004);
+ b43_phy_write(dev, 0x0802, b43_phy_read(dev, 0x0802) & ~(0x1 | 0x2));
+ if (phy->rev >= 6) {
+ backup[12] = b43_phy_read(dev, 0x002E);
+ backup[13] = b43_phy_read(dev, 0x002F);
+ backup[14] = b43_phy_read(dev, 0x080F);
+ backup[15] = b43_phy_read(dev, 0x0810);
+ backup[16] = b43_phy_read(dev, 0x0801);
+ backup[17] = b43_phy_read(dev, 0x0060);
+ backup[18] = b43_phy_read(dev, 0x0014);
+ backup[19] = b43_phy_read(dev, 0x0478);
+
+ b43_phy_write(dev, 0x002E, 0);
+ b43_phy_write(dev, 0x002F, 0);
+ b43_phy_write(dev, 0x080F, 0);
+ b43_phy_write(dev, 0x0810, 0);
+ b43_phy_write(dev, 0x0478, b43_phy_read(dev, 0x0478) | 0x0100);
+ b43_phy_write(dev, 0x0801, b43_phy_read(dev, 0x0801) | 0x0040);
+ b43_phy_write(dev, 0x0060, b43_phy_read(dev, 0x0060) | 0x0040);
+ b43_phy_write(dev, 0x0014, b43_phy_read(dev, 0x0014) | 0x0200);
+ }
+ b43_radio_write16(dev, 0x007A, b43_radio_read16(dev, 0x007A) | 0x0070);
+ b43_radio_write16(dev, 0x007A, b43_radio_read16(dev, 0x007A) | 0x0080);
+ udelay(30);
+
+ v47F = (s16) ((b43_phy_read(dev, 0x047F) >> 8) & 0x003F);
+ if (v47F >= 0x20)
+ v47F -= 0x40;
+ if (v47F == 31) {
+ for (i = 7; i >= 4; i--) {
+ b43_radio_write16(dev, 0x007B, i);
+ udelay(20);
+ v47F =
+ (s16) ((b43_phy_read(dev, 0x047F) >> 8) & 0x003F);
+ if (v47F >= 0x20)
+ v47F -= 0x40;
+ if (v47F < 31 && saved == 0xFFFF)
+ saved = i;
+ }
+ if (saved == 0xFFFF)
+ saved = 4;
+ } else {
+ b43_radio_write16(dev, 0x007A,
+ b43_radio_read16(dev, 0x007A) & 0x007F);
+ if (phy->rev != 1) { /* Not in specs, but needed to prevent PPC machine check */
+ b43_phy_write(dev, 0x0814,
+ b43_phy_read(dev, 0x0814) | 0x0001);
+ b43_phy_write(dev, 0x0815,
+ b43_phy_read(dev, 0x0815) & 0xFFFE);
+ }
+ b43_phy_write(dev, 0x0811, b43_phy_read(dev, 0x0811) | 0x000C);
+ b43_phy_write(dev, 0x0812, b43_phy_read(dev, 0x0812) | 0x000C);
+ b43_phy_write(dev, 0x0811, b43_phy_read(dev, 0x0811) | 0x0030);
+ b43_phy_write(dev, 0x0812, b43_phy_read(dev, 0x0812) | 0x0030);
+ b43_phy_write(dev, 0x005A, 0x0480);
+ b43_phy_write(dev, 0x0059, 0x0810);
+ b43_phy_write(dev, 0x0058, 0x000D);
+ if (phy->rev == 0) {
+ b43_phy_write(dev, 0x0003, 0x0122);
+ } else {
+ b43_phy_write(dev, 0x000A, b43_phy_read(dev, 0x000A)
+ | 0x2000);
+ }
+ if (phy->rev != 1) { /* Not in specs, but needed to prevent PPC machine check */
+ b43_phy_write(dev, 0x0814,
+ b43_phy_read(dev, 0x0814) | 0x0004);
+ b43_phy_write(dev, 0x0815,
+ b43_phy_read(dev, 0x0815) & 0xFFFB);
+ }
+ b43_phy_write(dev, 0x0003, (b43_phy_read(dev, 0x0003) & 0xFF9F)
+ | 0x0040);
+ b43_radio_write16(dev, 0x007A,
+ b43_radio_read16(dev, 0x007A) | 0x000F);
+ b43_set_all_gains(dev, 3, 0, 1);
+ b43_radio_write16(dev, 0x0043, (b43_radio_read16(dev, 0x0043)
+ & 0x00F0) | 0x000F);
+ udelay(30);
+ v47F = (s16) ((b43_phy_read(dev, 0x047F) >> 8) & 0x003F);
+ if (v47F >= 0x20)
+ v47F -= 0x40;
+ if (v47F == -32) {
+ for (i = 0; i < 4; i++) {
+ b43_radio_write16(dev, 0x007B, i);
+ udelay(20);
+ v47F =
+ (s16) ((b43_phy_read(dev, 0x047F) >> 8) &
+ 0x003F);
+ if (v47F >= 0x20)
+ v47F -= 0x40;
+ if (v47F > -31 && saved == 0xFFFF)
+ saved = i;
+ }
+ if (saved == 0xFFFF)
+ saved = 3;
+ } else
+ saved = 0;
+ }
+ b43_radio_write16(dev, 0x007B, saved);
+
+ if (phy->rev >= 6) {
+ b43_phy_write(dev, 0x002E, backup[12]);
+ b43_phy_write(dev, 0x002F, backup[13]);
+ b43_phy_write(dev, 0x080F, backup[14]);
+ b43_phy_write(dev, 0x0810, backup[15]);
+ }
+ if (phy->rev != 1) { /* Not in specs, but needed to prevent PPC machine check */
+ b43_phy_write(dev, 0x0814, backup[3]);
+ b43_phy_write(dev, 0x0815, backup[4]);
+ }
+ b43_phy_write(dev, 0x005A, backup[5]);
+ b43_phy_write(dev, 0x0059, backup[6]);
+ b43_phy_write(dev, 0x0058, backup[7]);
+ b43_phy_write(dev, 0x000A, backup[8]);
+ b43_phy_write(dev, 0x0003, backup[9]);
+ b43_radio_write16(dev, 0x0043, backup[11]);
+ b43_radio_write16(dev, 0x007A, backup[10]);
+ b43_phy_write(dev, 0x0802, b43_phy_read(dev, 0x0802) | 0x1 | 0x2);
+ b43_phy_write(dev, 0x0429, b43_phy_read(dev, 0x0429) | 0x8000);
+ b43_set_original_gains(dev);
+ if (phy->rev >= 6) {
+ b43_phy_write(dev, 0x0801, backup[16]);
+ b43_phy_write(dev, 0x0060, backup[17]);
+ b43_phy_write(dev, 0x0014, backup[18]);
+ b43_phy_write(dev, 0x0478, backup[19]);
+ }
+ b43_phy_write(dev, 0x0001, backup[0]);
+ b43_phy_write(dev, 0x0812, backup[2]);
+ b43_phy_write(dev, 0x0811, backup[1]);
+}
+
+void b43_calc_nrssi_slope(struct b43_wldev *dev)
+{
+ struct b43_phy *phy = &dev->phy;
+ u16 backup[18] = { 0 };
+ u16 tmp;
+ s16 nrssi0, nrssi1;
+
+ switch (phy->type) {
+ case B43_PHYTYPE_B:
+ backup[0] = b43_radio_read16(dev, 0x007A);
+ backup[1] = b43_radio_read16(dev, 0x0052);
+ backup[2] = b43_radio_read16(dev, 0x0043);
+ backup[3] = b43_phy_read(dev, 0x0030);
+ backup[4] = b43_phy_read(dev, 0x0026);
+ backup[5] = b43_phy_read(dev, 0x0015);
+ backup[6] = b43_phy_read(dev, 0x002A);
+ backup[7] = b43_phy_read(dev, 0x0020);
+ backup[8] = b43_phy_read(dev, 0x005A);
+ backup[9] = b43_phy_read(dev, 0x0059);
+ backup[10] = b43_phy_read(dev, 0x0058);
+ backup[11] = b43_read16(dev, 0x03E2);
+ backup[12] = b43_read16(dev, 0x03E6);
+ backup[13] = b43_read16(dev, B43_MMIO_CHANNEL_EXT);
+
+ tmp = b43_radio_read16(dev, 0x007A);
+ tmp &= (phy->rev >= 5) ? 0x007F : 0x000F;
+ b43_radio_write16(dev, 0x007A, tmp);
+ b43_phy_write(dev, 0x0030, 0x00FF);
+ b43_write16(dev, 0x03EC, 0x7F7F);
+ b43_phy_write(dev, 0x0026, 0x0000);
+ b43_phy_write(dev, 0x0015, b43_phy_read(dev, 0x0015) | 0x0020);
+ b43_phy_write(dev, 0x002A, 0x08A3);
+ b43_radio_write16(dev, 0x007A,
+ b43_radio_read16(dev, 0x007A) | 0x0080);
+
+ nrssi0 = (s16) b43_phy_read(dev, 0x0027);
+ b43_radio_write16(dev, 0x007A,
+ b43_radio_read16(dev, 0x007A) & 0x007F);
+ if (phy->rev >= 2) {
+ b43_write16(dev, 0x03E6, 0x0040);
+ } else if (phy->rev == 0) {
+ b43_write16(dev, 0x03E6, 0x0122);
+ } else {
+ b43_write16(dev, B43_MMIO_CHANNEL_EXT,
+ b43_read16(dev,
+ B43_MMIO_CHANNEL_EXT) & 0x2000);
+ }
+ b43_phy_write(dev, 0x0020, 0x3F3F);
+ b43_phy_write(dev, 0x0015, 0xF330);
+ b43_radio_write16(dev, 0x005A, 0x0060);
+ b43_radio_write16(dev, 0x0043,
+ b43_radio_read16(dev, 0x0043) & 0x00F0);
+ b43_phy_write(dev, 0x005A, 0x0480);
+ b43_phy_write(dev, 0x0059, 0x0810);
+ b43_phy_write(dev, 0x0058, 0x000D);
+ udelay(20);
+
+ nrssi1 = (s16) b43_phy_read(dev, 0x0027);
+ b43_phy_write(dev, 0x0030, backup[3]);
+ b43_radio_write16(dev, 0x007A, backup[0]);
+ b43_write16(dev, 0x03E2, backup[11]);
+ b43_phy_write(dev, 0x0026, backup[4]);
+ b43_phy_write(dev, 0x0015, backup[5]);
+ b43_phy_write(dev, 0x002A, backup[6]);
+ b43_synth_pu_workaround(dev, phy->channel);
+ if (phy->rev != 0)
+ b43_write16(dev, 0x03F4, backup[13]);
+
+ b43_phy_write(dev, 0x0020, backup[7]);
+ b43_phy_write(dev, 0x005A, backup[8]);
+ b43_phy_write(dev, 0x0059, backup[9]);
+ b43_phy_write(dev, 0x0058, backup[10]);
+ b43_radio_write16(dev, 0x0052, backup[1]);
+ b43_radio_write16(dev, 0x0043, backup[2]);
+
+ if (nrssi0 == nrssi1)
+ phy->nrssislope = 0x00010000;
+ else
+ phy->nrssislope = 0x00400000 / (nrssi0 - nrssi1);
+
+ if (nrssi0 <= -4) {
+ phy->nrssi[0] = nrssi0;
+ phy->nrssi[1] = nrssi1;
+ }
+ break;
+ case B43_PHYTYPE_G:
+ if (phy->radio_rev >= 9)
+ return;
+ if (phy->radio_rev == 8)
+ b43_calc_nrssi_offset(dev);
+
+ b43_phy_write(dev, B43_PHY_G_CRS,
+ b43_phy_read(dev, B43_PHY_G_CRS) & 0x7FFF);
+ b43_phy_write(dev, 0x0802, b43_phy_read(dev, 0x0802) & 0xFFFC);
+ backup[7] = b43_read16(dev, 0x03E2);
+ b43_write16(dev, 0x03E2, b43_read16(dev, 0x03E2) | 0x8000);
+ backup[0] = b43_radio_read16(dev, 0x007A);
+ backup[1] = b43_radio_read16(dev, 0x0052);
+ backup[2] = b43_radio_read16(dev, 0x0043);
+ backup[3] = b43_phy_read(dev, 0x0015);
+ backup[4] = b43_phy_read(dev, 0x005A);
+ backup[5] = b43_phy_read(dev, 0x0059);
+ backup[6] = b43_phy_read(dev, 0x0058);
+ backup[8] = b43_read16(dev, 0x03E6);
+ backup[9] = b43_read16(dev, B43_MMIO_CHANNEL_EXT);
+ if (phy->rev >= 3) {
+ backup[10] = b43_phy_read(dev, 0x002E);
+ backup[11] = b43_phy_read(dev, 0x002F);
+ backup[12] = b43_phy_read(dev, 0x080F);
+ backup[13] = b43_phy_read(dev, B43_PHY_G_LO_CONTROL);
+ backup[14] = b43_phy_read(dev, 0x0801);
+ backup[15] = b43_phy_read(dev, 0x0060);
+ backup[16] = b43_phy_read(dev, 0x0014);
+ backup[17] = b43_phy_read(dev, 0x0478);
+ b43_phy_write(dev, 0x002E, 0);
+ b43_phy_write(dev, B43_PHY_G_LO_CONTROL, 0);
+ switch (phy->rev) {
+ case 4:
+ case 6:
+ case 7:
+ b43_phy_write(dev, 0x0478,
+ b43_phy_read(dev, 0x0478)
+ | 0x0100);
+ b43_phy_write(dev, 0x0801,
+ b43_phy_read(dev, 0x0801)
+ | 0x0040);
+ break;
+ case 3:
+ case 5:
+ b43_phy_write(dev, 0x0801,
+ b43_phy_read(dev, 0x0801)
+ & 0xFFBF);
+ break;
+ }
+ b43_phy_write(dev, 0x0060, b43_phy_read(dev, 0x0060)
+ | 0x0040);
+ b43_phy_write(dev, 0x0014, b43_phy_read(dev, 0x0014)
+ | 0x0200);
+ }
+ b43_radio_write16(dev, 0x007A,
+ b43_radio_read16(dev, 0x007A) | 0x0070);
+ b43_set_all_gains(dev, 0, 8, 0);
+ b43_radio_write16(dev, 0x007A,
+ b43_radio_read16(dev, 0x007A) & 0x00F7);
+ if (phy->rev >= 2) {
+ b43_phy_write(dev, 0x0811,
+ (b43_phy_read(dev, 0x0811) & 0xFFCF) |
+ 0x0030);
+ b43_phy_write(dev, 0x0812,
+ (b43_phy_read(dev, 0x0812) & 0xFFCF) |
+ 0x0010);
+ }
+ b43_radio_write16(dev, 0x007A,
+ b43_radio_read16(dev, 0x007A) | 0x0080);
+ udelay(20);
+
+ nrssi0 = (s16) ((b43_phy_read(dev, 0x047F) >> 8) & 0x003F);
+ if (nrssi0 >= 0x0020)
+ nrssi0 -= 0x0040;
+
+ b43_radio_write16(dev, 0x007A,
+ b43_radio_read16(dev, 0x007A) & 0x007F);
+ if (phy->rev >= 2) {
+ b43_phy_write(dev, 0x0003, (b43_phy_read(dev, 0x0003)
+ & 0xFF9F) | 0x0040);
+ }
+
+ b43_write16(dev, B43_MMIO_CHANNEL_EXT,
+ b43_read16(dev, B43_MMIO_CHANNEL_EXT)
+ | 0x2000);
+ b43_radio_write16(dev, 0x007A,
+ b43_radio_read16(dev, 0x007A) | 0x000F);
+ b43_phy_write(dev, 0x0015, 0xF330);
+ if (phy->rev >= 2) {
+ b43_phy_write(dev, 0x0812,
+ (b43_phy_read(dev, 0x0812) & 0xFFCF) |
+ 0x0020);
+ b43_phy_write(dev, 0x0811,
+ (b43_phy_read(dev, 0x0811) & 0xFFCF) |
+ 0x0020);
+ }
+
+ b43_set_all_gains(dev, 3, 0, 1);
+ if (phy->radio_rev == 8) {
+ b43_radio_write16(dev, 0x0043, 0x001F);
+ } else {
+ tmp = b43_radio_read16(dev, 0x0052) & 0xFF0F;
+ b43_radio_write16(dev, 0x0052, tmp | 0x0060);
+ tmp = b43_radio_read16(dev, 0x0043) & 0xFFF0;
+ b43_radio_write16(dev, 0x0043, tmp | 0x0009);
+ }
+ b43_phy_write(dev, 0x005A, 0x0480);
+ b43_phy_write(dev, 0x0059, 0x0810);
+ b43_phy_write(dev, 0x0058, 0x000D);
+ udelay(20);
+ nrssi1 = (s16) ((b43_phy_read(dev, 0x047F) >> 8) & 0x003F);
+ if (nrssi1 >= 0x0020)
+ nrssi1 -= 0x0040;
+ if (nrssi0 == nrssi1)
+ phy->nrssislope = 0x00010000;
+ else
+ phy->nrssislope = 0x00400000 / (nrssi0 - nrssi1);
+ if (nrssi0 >= -4) {
+ phy->nrssi[0] = nrssi1;
+ phy->nrssi[1] = nrssi0;
+ }
+ if (phy->rev >= 3) {
+ b43_phy_write(dev, 0x002E, backup[10]);
+ b43_phy_write(dev, 0x002F, backup[11]);
+ b43_phy_write(dev, 0x080F, backup[12]);
+ b43_phy_write(dev, B43_PHY_G_LO_CONTROL, backup[13]);
+ }
+ if (phy->rev >= 2) {
+ b43_phy_write(dev, 0x0812,
+ b43_phy_read(dev, 0x0812) & 0xFFCF);
+ b43_phy_write(dev, 0x0811,
+ b43_phy_read(dev, 0x0811) & 0xFFCF);
+ }
+
+ b43_radio_write16(dev, 0x007A, backup[0]);
+ b43_radio_write16(dev, 0x0052, backup[1]);
+ b43_radio_write16(dev, 0x0043, backup[2]);
+ b43_write16(dev, 0x03E2, backup[7]);
+ b43_write16(dev, 0x03E6, backup[8]);
+ b43_write16(dev, B43_MMIO_CHANNEL_EXT, backup[9]);
+ b43_phy_write(dev, 0x0015, backup[3]);
+ b43_phy_write(dev, 0x005A, backup[4]);
+ b43_phy_write(dev, 0x0059, backup[5]);
+ b43_phy_write(dev, 0x0058, backup[6]);
+ b43_synth_pu_workaround(dev, phy->channel);
+ b43_phy_write(dev, 0x0802,
+ b43_phy_read(dev, 0x0802) | (0x0001 | 0x0002));
+ b43_set_original_gains(dev);
+ b43_phy_write(dev, B43_PHY_G_CRS,
+ b43_phy_read(dev, B43_PHY_G_CRS) | 0x8000);
+ if (phy->rev >= 3) {
+ b43_phy_write(dev, 0x0801, backup[14]);
+ b43_phy_write(dev, 0x0060, backup[15]);
+ b43_phy_write(dev, 0x0014, backup[16]);
+ b43_phy_write(dev, 0x0478, backup[17]);
+ }
+ b43_nrssi_mem_update(dev);
+ b43_calc_nrssi_threshold(dev);
+ break;
+ default:
+ B43_WARN_ON(1);
+ }
+}
+
+void b43_calc_nrssi_threshold(struct b43_wldev *dev)
+{
+ struct b43_phy *phy = &dev->phy;
+ s32 threshold;
+ s32 a, b;
+ s16 tmp16;
+ u16 tmp_u16;
+
+ switch (phy->type) {
+ case B43_PHYTYPE_B:{
+ if (phy->radio_ver != 0x2050)
+ return;
+ if (!
+ (dev->dev->bus->sprom.r1.
+ boardflags_lo & B43_BFL_RSSI))
+ return;
+
+ if (phy->radio_rev >= 6) {
+ threshold =
+ (phy->nrssi[1] - phy->nrssi[0]) * 32;
+ threshold += 20 * (phy->nrssi[0] + 1);
+ threshold /= 40;
+ } else
+ threshold = phy->nrssi[1] - 5;
+
+ threshold = limit_value(threshold, 0, 0x3E);
+ b43_phy_read(dev, 0x0020); /* dummy read */
+ b43_phy_write(dev, 0x0020,
+ (((u16) threshold) << 8) | 0x001C);
+
+ if (phy->radio_rev >= 6) {
+ b43_phy_write(dev, 0x0087, 0x0E0D);
+ b43_phy_write(dev, 0x0086, 0x0C0B);
+ b43_phy_write(dev, 0x0085, 0x0A09);
+ b43_phy_write(dev, 0x0084, 0x0808);
+ b43_phy_write(dev, 0x0083, 0x0808);
+ b43_phy_write(dev, 0x0082, 0x0604);
+ b43_phy_write(dev, 0x0081, 0x0302);
+ b43_phy_write(dev, 0x0080, 0x0100);
+ }
+ break;
+ }
+ case B43_PHYTYPE_G:
+ if (!phy->gmode ||
+ !(dev->dev->bus->sprom.r1.boardflags_lo & B43_BFL_RSSI)) {
+ tmp16 = b43_nrssi_hw_read(dev, 0x20);
+ if (tmp16 >= 0x20)
+ tmp16 -= 0x40;
+ if (tmp16 < 3) {
+ b43_phy_write(dev, 0x048A,
+ (b43_phy_read(dev, 0x048A)
+ & 0xF000) | 0x09EB);
+ } else {
+ b43_phy_write(dev, 0x048A,
+ (b43_phy_read(dev, 0x048A)
+ & 0xF000) | 0x0AED);
+ }
+ } else {
+ if (phy->interfmode == B43_INTERFMODE_NONWLAN) {
+ a = 0xE;
+ b = 0xA;
+ } else if (!phy->aci_wlan_automatic && phy->aci_enable) {
+ a = 0x13;
+ b = 0x12;
+ } else {
+ a = 0xE;
+ b = 0x11;
+ }
+
+ a = a * (phy->nrssi[1] - phy->nrssi[0]);
+ a += (phy->nrssi[0] << 6);
+ if (a < 32)
+ a += 31;
+ else
+ a += 32;
+ a = a >> 6;
+ a = limit_value(a, -31, 31);
+
+ b = b * (phy->nrssi[1] - phy->nrssi[0]);
+ b += (phy->nrssi[0] << 6);
+ if (b < 32)
+ b += 31;
+ else
+ b += 32;
+ b = b >> 6;
+ b = limit_value(b, -31, 31);
+
+ tmp_u16 = b43_phy_read(dev, 0x048A) & 0xF000;
+ tmp_u16 |= ((u32) b & 0x0000003F);
+ tmp_u16 |= (((u32) a & 0x0000003F) << 6);
+ b43_phy_write(dev, 0x048A, tmp_u16);
+ }
+ break;
+ default:
+ B43_WARN_ON(1);
+ }
+}
+
+/* Stack implementation to save/restore values from the
+ * interference mitigation code.
+ * It is save to restore values in random order.
+ */
+static void _stack_save(u32 * _stackptr, size_t * stackidx,
+ u8 id, u16 offset, u16 value)
+{
+ u32 *stackptr = &(_stackptr[*stackidx]);
+
+ B43_WARN_ON(offset & 0xF000);
+ B43_WARN_ON(id & 0xF0);
+ *stackptr = offset;
+ *stackptr |= ((u32) id) << 12;
+ *stackptr |= ((u32) value) << 16;
+ (*stackidx)++;
+ B43_WARN_ON(*stackidx >= B43_INTERFSTACK_SIZE);
+}
+
+static u16 _stack_restore(u32 * stackptr, u8 id, u16 offset)
+{
+ size_t i;
+
+ B43_WARN_ON(offset & 0xF000);
+ B43_WARN_ON(id & 0xF0);
+ for (i = 0; i < B43_INTERFSTACK_SIZE; i++, stackptr++) {
+ if ((*stackptr & 0x00000FFF) != offset)
+ continue;
+ if (((*stackptr & 0x0000F000) >> 12) != id)
+ continue;
+ return ((*stackptr & 0xFFFF0000) >> 16);
+ }
+ B43_WARN_ON(1);
+
+ return 0;
+}
+
+#define phy_stacksave(offset) \
+ do { \
+ _stack_save(stack, &stackidx, 0x1, (offset), \
+ b43_phy_read(dev, (offset))); \
+ } while (0)
+#define phy_stackrestore(offset) \
+ do { \
+ b43_phy_write(dev, (offset), \
+ _stack_restore(stack, 0x1, \
+ (offset))); \
+ } while (0)
+#define radio_stacksave(offset) \
+ do { \
+ _stack_save(stack, &stackidx, 0x2, (offset), \
+ b43_radio_read16(dev, (offset))); \
+ } while (0)
+#define radio_stackrestore(offset) \
+ do { \
+ b43_radio_write16(dev, (offset), \
+ _stack_restore(stack, 0x2, \
+ (offset))); \
+ } while (0)
+#define ofdmtab_stacksave(table, offset) \
+ do { \
+ _stack_save(stack, &stackidx, 0x3, (offset)|(table), \
+ b43_ofdmtab_read16(dev, (table), (offset))); \
+ } while (0)
+#define ofdmtab_stackrestore(table, offset) \
+ do { \
+ b43_ofdmtab_write16(dev, (table), (offset), \
+ _stack_restore(stack, 0x3, \
+ (offset)|(table))); \
+ } while (0)
+
+static void
+b43_radio_interference_mitigation_enable(struct b43_wldev *dev, int mode)
+{
+ struct b43_phy *phy = &dev->phy;
+ u16 tmp, flipped;
+ size_t stackidx = 0;
+ u32 *stack = phy->interfstack;
+
+ switch (mode) {
+ case B43_INTERFMODE_NONWLAN:
+ if (phy->rev != 1) {
+ b43_phy_write(dev, 0x042B,
+ b43_phy_read(dev, 0x042B) | 0x0800);
+ b43_phy_write(dev, B43_PHY_G_CRS,
+ b43_phy_read(dev,
+ B43_PHY_G_CRS) & ~0x4000);
+ break;
+ }
+ radio_stacksave(0x0078);
+ tmp = (b43_radio_read16(dev, 0x0078) & 0x001E);
+ flipped = flip_4bit(tmp);
+ if (flipped < 10 && flipped >= 8)
+ flipped = 7;
+ else if (flipped >= 10)
+ flipped -= 3;
+ flipped = flip_4bit(flipped);
+ flipped = (flipped << 1) | 0x0020;
+ b43_radio_write16(dev, 0x0078, flipped);
+
+ b43_calc_nrssi_threshold(dev);
+
+ phy_stacksave(0x0406);
+ b43_phy_write(dev, 0x0406, 0x7E28);
+
+ b43_phy_write(dev, 0x042B, b43_phy_read(dev, 0x042B) | 0x0800);
+ b43_phy_write(dev, B43_PHY_RADIO_BITFIELD,
+ b43_phy_read(dev,
+ B43_PHY_RADIO_BITFIELD) | 0x1000);
+
+ phy_stacksave(0x04A0);
+ b43_phy_write(dev, 0x04A0,
+ (b43_phy_read(dev, 0x04A0) & 0xC0C0) | 0x0008);
+ phy_stacksave(0x04A1);
+ b43_phy_write(dev, 0x04A1,
+ (b43_phy_read(dev, 0x04A1) & 0xC0C0) | 0x0605);
+ phy_stacksave(0x04A2);
+ b43_phy_write(dev, 0x04A2,
+ (b43_phy_read(dev, 0x04A2) & 0xC0C0) | 0x0204);
+ phy_stacksave(0x04A8);
+ b43_phy_write(dev, 0x04A8,
+ (b43_phy_read(dev, 0x04A8) & 0xC0C0) | 0x0803);
+ phy_stacksave(0x04AB);
+ b43_phy_write(dev, 0x04AB,
+ (b43_phy_read(dev, 0x04AB) & 0xC0C0) | 0x0605);
+
+ phy_stacksave(0x04A7);
+ b43_phy_write(dev, 0x04A7, 0x0002);
+ phy_stacksave(0x04A3);
+ b43_phy_write(dev, 0x04A3, 0x287A);
+ phy_stacksave(0x04A9);
+ b43_phy_write(dev, 0x04A9, 0x2027);
+ phy_stacksave(0x0493);
+ b43_phy_write(dev, 0x0493, 0x32F5);
+ phy_stacksave(0x04AA);
+ b43_phy_write(dev, 0x04AA, 0x2027);
+ phy_stacksave(0x04AC);
+ b43_phy_write(dev, 0x04AC, 0x32F5);
+ break;
+ case B43_INTERFMODE_MANUALWLAN:
+ if (b43_phy_read(dev, 0x0033) & 0x0800)
+ break;
+
+ phy->aci_enable = 1;
+
+ phy_stacksave(B43_PHY_RADIO_BITFIELD);
+ phy_stacksave(B43_PHY_G_CRS);
+ if (phy->rev < 2) {
+ phy_stacksave(0x0406);
+ } else {
+ phy_stacksave(0x04C0);
+ phy_stacksave(0x04C1);
+ }
+ phy_stacksave(0x0033);
+ phy_stacksave(0x04A7);
+ phy_stacksave(0x04A3);
+ phy_stacksave(0x04A9);
+ phy_stacksave(0x04AA);
+ phy_stacksave(0x04AC);
+ phy_stacksave(0x0493);
+ phy_stacksave(0x04A1);
+ phy_stacksave(0x04A0);
+ phy_stacksave(0x04A2);
+ phy_stacksave(0x048A);
+ phy_stacksave(0x04A8);
+ phy_stacksave(0x04AB);
+ if (phy->rev == 2) {
+ phy_stacksave(0x04AD);
+ phy_stacksave(0x04AE);
+ } else if (phy->rev >= 3) {
+ phy_stacksave(0x04AD);
+ phy_stacksave(0x0415);
+ phy_stacksave(0x0416);
+ phy_stacksave(0x0417);
+ ofdmtab_stacksave(0x1A00, 0x2);
+ ofdmtab_stacksave(0x1A00, 0x3);
+ }
+ phy_stacksave(0x042B);
+ phy_stacksave(0x048C);
+
+ b43_phy_write(dev, B43_PHY_RADIO_BITFIELD,
+ b43_phy_read(dev, B43_PHY_RADIO_BITFIELD)
+ & ~0x1000);
+ b43_phy_write(dev, B43_PHY_G_CRS,
+ (b43_phy_read(dev, B43_PHY_G_CRS)
+ & 0xFFFC) | 0x0002);
+
+ b43_phy_write(dev, 0x0033, 0x0800);
+ b43_phy_write(dev, 0x04A3, 0x2027);
+ b43_phy_write(dev, 0x04A9, 0x1CA8);
+ b43_phy_write(dev, 0x0493, 0x287A);
+ b43_phy_write(dev, 0x04AA, 0x1CA8);
+ b43_phy_write(dev, 0x04AC, 0x287A);
+
+ b43_phy_write(dev, 0x04A0, (b43_phy_read(dev, 0x04A0)
+ & 0xFFC0) | 0x001A);
+ b43_phy_write(dev, 0x04A7, 0x000D);
+
+ if (phy->rev < 2) {
+ b43_phy_write(dev, 0x0406, 0xFF0D);
+ } else if (phy->rev == 2) {
+ b43_phy_write(dev, 0x04C0, 0xFFFF);
+ b43_phy_write(dev, 0x04C1, 0x00A9);
+ } else {
+ b43_phy_write(dev, 0x04C0, 0x00C1);
+ b43_phy_write(dev, 0x04C1, 0x0059);
+ }
+
+ b43_phy_write(dev, 0x04A1, (b43_phy_read(dev, 0x04A1)
+ & 0xC0FF) | 0x1800);
+ b43_phy_write(dev, 0x04A1, (b43_phy_read(dev, 0x04A1)
+ & 0xFFC0) | 0x0015);
+ b43_phy_write(dev, 0x04A8, (b43_phy_read(dev, 0x04A8)
+ & 0xCFFF) | 0x1000);
+ b43_phy_write(dev, 0x04A8, (b43_phy_read(dev, 0x04A8)
+ & 0xF0FF) | 0x0A00);
+ b43_phy_write(dev, 0x04AB, (b43_phy_read(dev, 0x04AB)
+ & 0xCFFF) | 0x1000);
+ b43_phy_write(dev, 0x04AB, (b43_phy_read(dev, 0x04AB)
+ & 0xF0FF) | 0x0800);
+ b43_phy_write(dev, 0x04AB, (b43_phy_read(dev, 0x04AB)
+ & 0xFFCF) | 0x0010);
+ b43_phy_write(dev, 0x04AB, (b43_phy_read(dev, 0x04AB)
+ & 0xFFF0) | 0x0005);
+ b43_phy_write(dev, 0x04A8, (b43_phy_read(dev, 0x04A8)
+ & 0xFFCF) | 0x0010);
+ b43_phy_write(dev, 0x04A8, (b43_phy_read(dev, 0x04A8)
+ & 0xFFF0) | 0x0006);
+ b43_phy_write(dev, 0x04A2, (b43_phy_read(dev, 0x04A2)
+ & 0xF0FF) | 0x0800);
+ b43_phy_write(dev, 0x04A0, (b43_phy_read(dev, 0x04A0)
+ & 0xF0FF) | 0x0500);
+ b43_phy_write(dev, 0x04A2, (b43_phy_read(dev, 0x04A2)
+ & 0xFFF0) | 0x000B);
+
+ if (phy->rev >= 3) {
+ b43_phy_write(dev, 0x048A, b43_phy_read(dev, 0x048A)
+ & ~0x8000);
+ b43_phy_write(dev, 0x0415, (b43_phy_read(dev, 0x0415)
+ & 0x8000) | 0x36D8);
+ b43_phy_write(dev, 0x0416, (b43_phy_read(dev, 0x0416)
+ & 0x8000) | 0x36D8);
+ b43_phy_write(dev, 0x0417, (b43_phy_read(dev, 0x0417)
+ & 0xFE00) | 0x016D);
+ } else {
+ b43_phy_write(dev, 0x048A, b43_phy_read(dev, 0x048A)
+ | 0x1000);
+ b43_phy_write(dev, 0x048A, (b43_phy_read(dev, 0x048A)
+ & 0x9FFF) | 0x2000);
+ b43_hf_write(dev, b43_hf_read(dev) | B43_HF_ACIW);
+ }
+ if (phy->rev >= 2) {
+ b43_phy_write(dev, 0x042B, b43_phy_read(dev, 0x042B)
+ | 0x0800);
+ }
+ b43_phy_write(dev, 0x048C, (b43_phy_read(dev, 0x048C)
+ & 0xF0FF) | 0x0200);
+ if (phy->rev == 2) {
+ b43_phy_write(dev, 0x04AE, (b43_phy_read(dev, 0x04AE)
+ & 0xFF00) | 0x007F);
+ b43_phy_write(dev, 0x04AD, (b43_phy_read(dev, 0x04AD)
+ & 0x00FF) | 0x1300);
+ } else if (phy->rev >= 6) {
+ b43_ofdmtab_write16(dev, 0x1A00, 0x3, 0x007F);
+ b43_ofdmtab_write16(dev, 0x1A00, 0x2, 0x007F);
+ b43_phy_write(dev, 0x04AD, b43_phy_read(dev, 0x04AD)
+ & 0x00FF);
+ }
+ b43_calc_nrssi_slope(dev);
+ break;
+ default:
+ B43_WARN_ON(1);
+ }
+}
+
+static void
+b43_radio_interference_mitigation_disable(struct b43_wldev *dev, int mode)
+{
+ struct b43_phy *phy = &dev->phy;
+ u32 *stack = phy->interfstack;
+
+ switch (mode) {
+ case B43_INTERFMODE_NONWLAN:
+ if (phy->rev != 1) {
+ b43_phy_write(dev, 0x042B,
+ b43_phy_read(dev, 0x042B) & ~0x0800);
+ b43_phy_write(dev, B43_PHY_G_CRS,
+ b43_phy_read(dev,
+ B43_PHY_G_CRS) | 0x4000);
+ break;
+ }
+ radio_stackrestore(0x0078);
+ b43_calc_nrssi_threshold(dev);
+ phy_stackrestore(0x0406);
+ b43_phy_write(dev, 0x042B, b43_phy_read(dev, 0x042B) & ~0x0800);
+ if (!dev->bad_frames_preempt) {
+ b43_phy_write(dev, B43_PHY_RADIO_BITFIELD,
+ b43_phy_read(dev, B43_PHY_RADIO_BITFIELD)
+ & ~(1 << 11));
+ }
+ b43_phy_write(dev, B43_PHY_G_CRS,
+ b43_phy_read(dev, B43_PHY_G_CRS) | 0x4000);
+ phy_stackrestore(0x04A0);
+ phy_stackrestore(0x04A1);
+ phy_stackrestore(0x04A2);
+ phy_stackrestore(0x04A8);
+ phy_stackrestore(0x04AB);
+ phy_stackrestore(0x04A7);
+ phy_stackrestore(0x04A3);
+ phy_stackrestore(0x04A9);
+ phy_stackrestore(0x0493);
+ phy_stackrestore(0x04AA);
+ phy_stackrestore(0x04AC);
+ break;
+ case B43_INTERFMODE_MANUALWLAN:
+ if (!(b43_phy_read(dev, 0x0033) & 0x0800))
+ break;
+
+ phy->aci_enable = 0;
+
+ phy_stackrestore(B43_PHY_RADIO_BITFIELD);
+ phy_stackrestore(B43_PHY_G_CRS);
+ phy_stackrestore(0x0033);
+ phy_stackrestore(0x04A3);
+ phy_stackrestore(0x04A9);
+ phy_stackrestore(0x0493);
+ phy_stackrestore(0x04AA);
+ phy_stackrestore(0x04AC);
+ phy_stackrestore(0x04A0);
+ phy_stackrestore(0x04A7);
+ if (phy->rev >= 2) {
+ phy_stackrestore(0x04C0);
+ phy_stackrestore(0x04C1);
+ } else
+ phy_stackrestore(0x0406);
+ phy_stackrestore(0x04A1);
+ phy_stackrestore(0x04AB);
+ phy_stackrestore(0x04A8);
+ if (phy->rev == 2) {
+ phy_stackrestore(0x04AD);
+ phy_stackrestore(0x04AE);
+ } else if (phy->rev >= 3) {
+ phy_stackrestore(0x04AD);
+ phy_stackrestore(0x0415);
+ phy_stackrestore(0x0416);
+ phy_stackrestore(0x0417);
+ ofdmtab_stackrestore(0x1A00, 0x2);
+ ofdmtab_stackrestore(0x1A00, 0x3);
+ }
+ phy_stackrestore(0x04A2);
+ phy_stackrestore(0x048A);
+ phy_stackrestore(0x042B);
+ phy_stackrestore(0x048C);
+ b43_hf_write(dev, b43_hf_read(dev) & ~B43_HF_ACIW);
+ b43_calc_nrssi_slope(dev);
+ break;
+ default:
+ B43_WARN_ON(1);
+ }
+}
+
+#undef phy_stacksave
+#undef phy_stackrestore
+#undef radio_stacksave
+#undef radio_stackrestore
+#undef ofdmtab_stacksave
+#undef ofdmtab_stackrestore
+
+int b43_radio_set_interference_mitigation(struct b43_wldev *dev, int mode)
+{
+ struct b43_phy *phy = &dev->phy;
+ int currentmode;
+
+ if ((phy->type != B43_PHYTYPE_G) || (phy->rev == 0) || (!phy->gmode))
+ return -ENODEV;
+
+ phy->aci_wlan_automatic = 0;
+ switch (mode) {
+ case B43_INTERFMODE_AUTOWLAN:
+ phy->aci_wlan_automatic = 1;
+ if (phy->aci_enable)
+ mode = B43_INTERFMODE_MANUALWLAN;
+ else
+ mode = B43_INTERFMODE_NONE;
+ break;
+ case B43_INTERFMODE_NONE:
+ case B43_INTERFMODE_NONWLAN:
+ case B43_INTERFMODE_MANUALWLAN:
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ currentmode = phy->interfmode;
+ if (currentmode == mode)
+ return 0;
+ if (currentmode != B43_INTERFMODE_NONE)
+ b43_radio_interference_mitigation_disable(dev, currentmode);
+
+ if (mode == B43_INTERFMODE_NONE) {
+ phy->aci_enable = 0;
+ phy->aci_hw_rssi = 0;
+ } else
+ b43_radio_interference_mitigation_enable(dev, mode);
+ phy->interfmode = mode;
+
+ return 0;
+}
+
+static u16 b43_radio_core_calibration_value(struct b43_wldev *dev)
+{
+ u16 reg, index, ret;
+
+ static const u8 rcc_table[] = {
+ 0x02, 0x03, 0x01, 0x0F,
+ 0x06, 0x07, 0x05, 0x0F,
+ 0x0A, 0x0B, 0x09, 0x0F,
+ 0x0E, 0x0F, 0x0D, 0x0F,
+ };
+
+ reg = b43_radio_read16(dev, 0x60);
+ index = (reg & 0x001E) >> 1;
+ ret = rcc_table[index] << 1;
+ ret |= (reg & 0x0001);
+ ret |= 0x0020;
+
+ return ret;
+}
+
+#define LPD(L, P, D) (((L) << 2) | ((P) << 1) | ((D) << 0))
+static u16 radio2050_rfover_val(struct b43_wldev *dev,
+ u16 phy_register, unsigned int lpd)
+{
+ struct b43_phy *phy = &dev->phy;
+ struct ssb_sprom *sprom = &(dev->dev->bus->sprom);
+
+ if (!phy->gmode)
+ return 0;
+
+ if (has_loopback_gain(phy)) {
+ int max_lb_gain = phy->max_lb_gain;
+ u16 extlna;
+ u16 i;
+
+ if (phy->radio_rev == 8)
+ max_lb_gain += 0x3E;
+ else
+ max_lb_gain += 0x26;
+ if (max_lb_gain >= 0x46) {
+ extlna = 0x3000;
+ max_lb_gain -= 0x46;
+ } else if (max_lb_gain >= 0x3A) {
+ extlna = 0x1000;
+ max_lb_gain -= 0x3A;
+ } else if (max_lb_gain >= 0x2E) {
+ extlna = 0x2000;
+ max_lb_gain -= 0x2E;
+ } else {
+ extlna = 0;
+ max_lb_gain -= 0x10;
+ }
+
+ for (i = 0; i < 16; i++) {
+ max_lb_gain -= (i * 6);
+ if (max_lb_gain < 6)
+ break;
+ }
+
+ if ((phy->rev < 7) ||
+ !(sprom->r1.boardflags_lo & B43_BFL_EXTLNA)) {
+ if (phy_register == B43_PHY_RFOVER) {
+ return 0x1B3;
+ } else if (phy_register == B43_PHY_RFOVERVAL) {
+ extlna |= (i << 8);
+ switch (lpd) {
+ case LPD(0, 1, 1):
+ return 0x0F92;
+ case LPD(0, 0, 1):
+ case LPD(1, 0, 1):
+ return (0x0092 | extlna);
+ case LPD(1, 0, 0):
+ return (0x0093 | extlna);
+ }
+ B43_WARN_ON(1);
+ }
+ B43_WARN_ON(1);
+ } else {
+ if (phy_register == B43_PHY_RFOVER) {
+ return 0x9B3;
+ } else if (phy_register == B43_PHY_RFOVERVAL) {
+ if (extlna)
+ extlna |= 0x8000;
+ extlna |= (i << 8);
+ switch (lpd) {
+ case LPD(0, 1, 1):
+ return 0x8F92;
+ case LPD(0, 0, 1):
+ return (0x8092 | extlna);
+ case LPD(1, 0, 1):
+ return (0x2092 | extlna);
+ case LPD(1, 0, 0):
+ return (0x2093 | extlna);
+ }
+ B43_WARN_ON(1);
+ }
+ B43_WARN_ON(1);
+ }
+ } else {
+ if ((phy->rev < 7) ||
+ !(sprom->r1.boardflags_lo & B43_BFL_EXTLNA)) {
+ if (phy_register == B43_PHY_RFOVER) {
+ return 0x1B3;
+ } else if (phy_register == B43_PHY_RFOVERVAL) {
+ switch (lpd) {
+ case LPD(0, 1, 1):
+ return 0x0FB2;
+ case LPD(0, 0, 1):
+ return 0x00B2;
+ case LPD(1, 0, 1):
+ return 0x30B2;
+ case LPD(1, 0, 0):
+ return 0x30B3;
+ }
+ B43_WARN_ON(1);
+ }
+ B43_WARN_ON(1);
+ } else {
+ if (phy_register == B43_PHY_RFOVER) {
+ return 0x9B3;
+ } else if (phy_register == B43_PHY_RFOVERVAL) {
+ switch (lpd) {
+ case LPD(0, 1, 1):
+ return 0x8FB2;
+ case LPD(0, 0, 1):
+ return 0x80B2;
+ case LPD(1, 0, 1):
+ return 0x20B2;
+ case LPD(1, 0, 0):
+ return 0x20B3;
+ }
+ B43_WARN_ON(1);
+ }
+ B43_WARN_ON(1);
+ }
+ }
+ return 0;
+}
+
+struct init2050_saved_values {
+ /* Core registers */
+ u16 reg_3EC;
+ u16 reg_3E6;
+ u16 reg_3F4;
+ /* Radio registers */
+ u16 radio_43;
+ u16 radio_51;
+ u16 radio_52;
+ /* PHY registers */
+ u16 phy_pgactl;
+ u16 phy_base_5A;
+ u16 phy_base_59;
+ u16 phy_base_58;
+ u16 phy_base_30;
+ u16 phy_rfover;
+ u16 phy_rfoverval;
+ u16 phy_analogover;
+ u16 phy_analogoverval;
+ u16 phy_crs0;
+ u16 phy_classctl;
+ u16 phy_lo_mask;
+ u16 phy_lo_ctl;
+ u16 phy_syncctl;
+};
+
+u16 b43_radio_init2050(struct b43_wldev *dev)
+{
+ struct b43_phy *phy = &dev->phy;
+ struct init2050_saved_values sav;
+ u16 rcc;
+ u16 radio78;
+ u16 ret;
+ u16 i, j;
+ u32 tmp1 = 0, tmp2 = 0;
+
+ memset(&sav, 0, sizeof(sav)); /* get rid of "may be used uninitialized..." */
+
+ sav.radio_43 = b43_radio_read16(dev, 0x43);
+ sav.radio_51 = b43_radio_read16(dev, 0x51);
+ sav.radio_52 = b43_radio_read16(dev, 0x52);
+ sav.phy_pgactl = b43_phy_read(dev, B43_PHY_PGACTL);
+ sav.phy_base_5A = b43_phy_read(dev, B43_PHY_BASE(0x5A));
+ sav.phy_base_59 = b43_phy_read(dev, B43_PHY_BASE(0x59));
+ sav.phy_base_58 = b43_phy_read(dev, B43_PHY_BASE(0x58));
+
+ if (phy->type == B43_PHYTYPE_B) {
+ sav.phy_base_30 = b43_phy_read(dev, B43_PHY_BASE(0x30));
+ sav.reg_3EC = b43_read16(dev, 0x3EC);
+
+ b43_phy_write(dev, B43_PHY_BASE(0x30), 0xFF);
+ b43_write16(dev, 0x3EC, 0x3F3F);
+ } else if (phy->gmode || phy->rev >= 2) {
+ sav.phy_rfover = b43_phy_read(dev, B43_PHY_RFOVER);
+ sav.phy_rfoverval = b43_phy_read(dev, B43_PHY_RFOVERVAL);
+ sav.phy_analogover = b43_phy_read(dev, B43_PHY_ANALOGOVER);
+ sav.phy_analogoverval =
+ b43_phy_read(dev, B43_PHY_ANALOGOVERVAL);
+ sav.phy_crs0 = b43_phy_read(dev, B43_PHY_CRS0);
+ sav.phy_classctl = b43_phy_read(dev, B43_PHY_CLASSCTL);
+
+ b43_phy_write(dev, B43_PHY_ANALOGOVER,
+ b43_phy_read(dev, B43_PHY_ANALOGOVER)
+ | 0x0003);
+ b43_phy_write(dev, B43_PHY_ANALOGOVERVAL,
+ b43_phy_read(dev, B43_PHY_ANALOGOVERVAL)
+ & 0xFFFC);
+ b43_phy_write(dev, B43_PHY_CRS0, b43_phy_read(dev, B43_PHY_CRS0)
+ & 0x7FFF);
+ b43_phy_write(dev, B43_PHY_CLASSCTL,
+ b43_phy_read(dev, B43_PHY_CLASSCTL)
+ & 0xFFFC);
+ if (has_loopback_gain(phy)) {
+ sav.phy_lo_mask = b43_phy_read(dev, B43_PHY_LO_MASK);
+ sav.phy_lo_ctl = b43_phy_read(dev, B43_PHY_LO_CTL);
+
+ if (phy->rev >= 3)
+ b43_phy_write(dev, B43_PHY_LO_MASK, 0xC020);
+ else
+ b43_phy_write(dev, B43_PHY_LO_MASK, 0x8020);
+ b43_phy_write(dev, B43_PHY_LO_CTL, 0);
+ }
+
+ b43_phy_write(dev, B43_PHY_RFOVERVAL,
+ radio2050_rfover_val(dev, B43_PHY_RFOVERVAL,
+ LPD(0, 1, 1)));
+ b43_phy_write(dev, B43_PHY_RFOVER,
+ radio2050_rfover_val(dev, B43_PHY_RFOVER, 0));
+ }
+ b43_write16(dev, 0x3E2, b43_read16(dev, 0x3E2) | 0x8000);
+
+ sav.phy_syncctl = b43_phy_read(dev, B43_PHY_SYNCCTL);
+ b43_phy_write(dev, B43_PHY_SYNCCTL, b43_phy_read(dev, B43_PHY_SYNCCTL)
+ & 0xFF7F);
+ sav.reg_3E6 = b43_read16(dev, 0x3E6);
+ sav.reg_3F4 = b43_read16(dev, 0x3F4);
+
+ if (phy->analog == 0) {
+ b43_write16(dev, 0x03E6, 0x0122);
+ } else {
+ if (phy->analog >= 2) {
+ b43_phy_write(dev, B43_PHY_BASE(0x03),
+ (b43_phy_read(dev, B43_PHY_BASE(0x03))
+ & 0xFFBF) | 0x40);
+ }
+ b43_write16(dev, B43_MMIO_CHANNEL_EXT,
+ (b43_read16(dev, B43_MMIO_CHANNEL_EXT) | 0x2000));
+ }
+
+ rcc = b43_radio_core_calibration_value(dev);
+
+ if (phy->type == B43_PHYTYPE_B)
+ b43_radio_write16(dev, 0x78, 0x26);
+ if (phy->gmode || phy->rev >= 2) {
+ b43_phy_write(dev, B43_PHY_RFOVERVAL,
+ radio2050_rfover_val(dev, B43_PHY_RFOVERVAL,
+ LPD(0, 1, 1)));
+ }
+ b43_phy_write(dev, B43_PHY_PGACTL, 0xBFAF);
+ b43_phy_write(dev, B43_PHY_BASE(0x2B), 0x1403);
+ if (phy->gmode || phy->rev >= 2) {
+ b43_phy_write(dev, B43_PHY_RFOVERVAL,
+ radio2050_rfover_val(dev, B43_PHY_RFOVERVAL,
+ LPD(0, 0, 1)));
+ }
+ b43_phy_write(dev, B43_PHY_PGACTL, 0xBFA0);
+ b43_radio_write16(dev, 0x51, b43_radio_read16(dev, 0x51)
+ | 0x0004);
+ if (phy->radio_rev == 8) {
+ b43_radio_write16(dev, 0x43, 0x1F);
+ } else {
+ b43_radio_write16(dev, 0x52, 0);
+ b43_radio_write16(dev, 0x43, (b43_radio_read16(dev, 0x43)
+ & 0xFFF0) | 0x0009);
+ }
+ b43_phy_write(dev, B43_PHY_BASE(0x58), 0);
+
+ for (i = 0; i < 16; i++) {
+ b43_phy_write(dev, B43_PHY_BASE(0x5A), 0x0480);
+ b43_phy_write(dev, B43_PHY_BASE(0x59), 0xC810);
+ b43_phy_write(dev, B43_PHY_BASE(0x58), 0x000D);
+ if (phy->gmode || phy->rev >= 2) {
+ b43_phy_write(dev, B43_PHY_RFOVERVAL,
+ radio2050_rfover_val(dev,
+ B43_PHY_RFOVERVAL,
+ LPD(1, 0, 1)));
+ }
+ b43_phy_write(dev, B43_PHY_PGACTL, 0xAFB0);
+ udelay(10);
+ if (phy->gmode || phy->rev >= 2) {
+ b43_phy_write(dev, B43_PHY_RFOVERVAL,
+ radio2050_rfover_val(dev,
+ B43_PHY_RFOVERVAL,
+ LPD(1, 0, 1)));
+ }
+ b43_phy_write(dev, B43_PHY_PGACTL, 0xEFB0);
+ udelay(10);
+ if (phy->gmode || phy->rev >= 2) {
+ b43_phy_write(dev, B43_PHY_RFOVERVAL,
+ radio2050_rfover_val(dev,
+ B43_PHY_RFOVERVAL,
+ LPD(1, 0, 0)));
+ }
+ b43_phy_write(dev, B43_PHY_PGACTL, 0xFFF0);
+ udelay(20);
+ tmp1 += b43_phy_read(dev, B43_PHY_LO_LEAKAGE);
+ b43_phy_write(dev, B43_PHY_BASE(0x58), 0);
+ if (phy->gmode || phy->rev >= 2) {
+ b43_phy_write(dev, B43_PHY_RFOVERVAL,
+ radio2050_rfover_val(dev,
+ B43_PHY_RFOVERVAL,
+ LPD(1, 0, 1)));
+ }
+ b43_phy_write(dev, B43_PHY_PGACTL, 0xAFB0);
+ }
+ udelay(10);
+
+ b43_phy_write(dev, B43_PHY_BASE(0x58), 0);
+ tmp1++;
+ tmp1 >>= 9;
+
+ for (i = 0; i < 16; i++) {
+ radio78 = ((flip_4bit(i) << 1) | 0x20);
+ b43_radio_write16(dev, 0x78, radio78);
+ udelay(10);
+ for (j = 0; j < 16; j++) {
+ b43_phy_write(dev, B43_PHY_BASE(0x5A), 0x0D80);
+ b43_phy_write(dev, B43_PHY_BASE(0x59), 0xC810);
+ b43_phy_write(dev, B43_PHY_BASE(0x58), 0x000D);
+ if (phy->gmode || phy->rev >= 2) {
+ b43_phy_write(dev, B43_PHY_RFOVERVAL,
+ radio2050_rfover_val(dev,
+ B43_PHY_RFOVERVAL,
+ LPD(1, 0,
+ 1)));
+ }
+ b43_phy_write(dev, B43_PHY_PGACTL, 0xAFB0);
+ udelay(10);
+ if (phy->gmode || phy->rev >= 2) {
+ b43_phy_write(dev, B43_PHY_RFOVERVAL,
+ radio2050_rfover_val(dev,
+ B43_PHY_RFOVERVAL,
+ LPD(1, 0,
+ 1)));
+ }
+ b43_phy_write(dev, B43_PHY_PGACTL, 0xEFB0);
+ udelay(10);
+ if (phy->gmode || phy->rev >= 2) {
+ b43_phy_write(dev, B43_PHY_RFOVERVAL,
+ radio2050_rfover_val(dev,
+ B43_PHY_RFOVERVAL,
+ LPD(1, 0,
+ 0)));
+ }
+ b43_phy_write(dev, B43_PHY_PGACTL, 0xFFF0);
+ udelay(10);
+ tmp2 += b43_phy_read(dev, B43_PHY_LO_LEAKAGE);
+ b43_phy_write(dev, B43_PHY_BASE(0x58), 0);
+ if (phy->gmode || phy->rev >= 2) {
+ b43_phy_write(dev, B43_PHY_RFOVERVAL,
+ radio2050_rfover_val(dev,
+ B43_PHY_RFOVERVAL,
+ LPD(1, 0,
+ 1)));
+ }
+ b43_phy_write(dev, B43_PHY_PGACTL, 0xAFB0);
+ }
+ tmp2++;
+ tmp2 >>= 8;
+ if (tmp1 < tmp2)
+ break;
+ }
+
+ /* Restore the registers */
+ b43_phy_write(dev, B43_PHY_PGACTL, sav.phy_pgactl);
+ b43_radio_write16(dev, 0x51, sav.radio_51);
+ b43_radio_write16(dev, 0x52, sav.radio_52);
+ b43_radio_write16(dev, 0x43, sav.radio_43);
+ b43_phy_write(dev, B43_PHY_BASE(0x5A), sav.phy_base_5A);
+ b43_phy_write(dev, B43_PHY_BASE(0x59), sav.phy_base_59);
+ b43_phy_write(dev, B43_PHY_BASE(0x58), sav.phy_base_58);
+ b43_write16(dev, 0x3E6, sav.reg_3E6);
+ if (phy->analog != 0)
+ b43_write16(dev, 0x3F4, sav.reg_3F4);
+ b43_phy_write(dev, B43_PHY_SYNCCTL, sav.phy_syncctl);
+ b43_synth_pu_workaround(dev, phy->channel);
+ if (phy->type == B43_PHYTYPE_B) {
+ b43_phy_write(dev, B43_PHY_BASE(0x30), sav.phy_base_30);
+ b43_write16(dev, 0x3EC, sav.reg_3EC);
+ } else if (phy->gmode) {
+ b43_write16(dev, B43_MMIO_PHY_RADIO,
+ b43_read16(dev, B43_MMIO_PHY_RADIO)
+ & 0x7FFF);
+ b43_phy_write(dev, B43_PHY_RFOVER, sav.phy_rfover);
+ b43_phy_write(dev, B43_PHY_RFOVERVAL, sav.phy_rfoverval);
+ b43_phy_write(dev, B43_PHY_ANALOGOVER, sav.phy_analogover);
+ b43_phy_write(dev, B43_PHY_ANALOGOVERVAL,
+ sav.phy_analogoverval);
+ b43_phy_write(dev, B43_PHY_CRS0, sav.phy_crs0);
+ b43_phy_write(dev, B43_PHY_CLASSCTL, sav.phy_classctl);
+ if (has_loopback_gain(phy)) {
+ b43_phy_write(dev, B43_PHY_LO_MASK, sav.phy_lo_mask);
+ b43_phy_write(dev, B43_PHY_LO_CTL, sav.phy_lo_ctl);
+ }
+ }
+ if (i > 15)
+ ret = radio78;
+ else
+ ret = rcc;
+
+ return ret;
+}
+
+void b43_radio_init2060(struct b43_wldev *dev)
+{
+ int err;
+
+ b43_radio_write16(dev, 0x0004, 0x00C0);
+ b43_radio_write16(dev, 0x0005, 0x0008);
+ b43_radio_write16(dev, 0x0009, 0x0040);
+ b43_radio_write16(dev, 0x0005, 0x00AA);
+ b43_radio_write16(dev, 0x0032, 0x008F);
+ b43_radio_write16(dev, 0x0006, 0x008F);
+ b43_radio_write16(dev, 0x0034, 0x008F);
+ b43_radio_write16(dev, 0x002C, 0x0007);
+ b43_radio_write16(dev, 0x0082, 0x0080);
+ b43_radio_write16(dev, 0x0080, 0x0000);
+ b43_radio_write16(dev, 0x003F, 0x00DA);
+ b43_radio_write16(dev, 0x0005, b43_radio_read16(dev, 0x0005) & ~0x0008);
+ b43_radio_write16(dev, 0x0081, b43_radio_read16(dev, 0x0081) & ~0x0010);
+ b43_radio_write16(dev, 0x0081, b43_radio_read16(dev, 0x0081) & ~0x0020);
+ b43_radio_write16(dev, 0x0081, b43_radio_read16(dev, 0x0081) & ~0x0020);
+ msleep(1); /* delay 400usec */
+
+ b43_radio_write16(dev, 0x0081,
+ (b43_radio_read16(dev, 0x0081) & ~0x0020) | 0x0010);
+ msleep(1); /* delay 400usec */
+
+ b43_radio_write16(dev, 0x0005,
+ (b43_radio_read16(dev, 0x0005) & ~0x0008) | 0x0008);
+ b43_radio_write16(dev, 0x0085, b43_radio_read16(dev, 0x0085) & ~0x0010);
+ b43_radio_write16(dev, 0x0005, b43_radio_read16(dev, 0x0005) & ~0x0008);
+ b43_radio_write16(dev, 0x0081, b43_radio_read16(dev, 0x0081) & ~0x0040);
+ b43_radio_write16(dev, 0x0081,
+ (b43_radio_read16(dev, 0x0081) & ~0x0040) | 0x0040);
+ b43_radio_write16(dev, 0x0005,
+ (b43_radio_read16(dev, 0x0081) & ~0x0008) | 0x0008);
+ b43_phy_write(dev, 0x0063, 0xDDC6);
+ b43_phy_write(dev, 0x0069, 0x07BE);
+ b43_phy_write(dev, 0x006A, 0x0000);
+
+ err = b43_radio_selectchannel(dev, B43_DEFAULT_CHANNEL_A, 0);
+ B43_WARN_ON(err);
+
+ msleep(1);
+}
+
+static inline u16 freq_r3A_value(u16 frequency)
+{
+ u16 value;
+
+ if (frequency < 5091)
+ value = 0x0040;
+ else if (frequency < 5321)
+ value = 0x0000;
+ else if (frequency < 5806)
+ value = 0x0080;
+ else
+ value = 0x0040;
+
+ return value;
+}
+
+void b43_radio_set_tx_iq(struct b43_wldev *dev)
+{
+ static const u8 data_high[5] = { 0x00, 0x40, 0x80, 0x90, 0xD0 };
+ static const u8 data_low[5] = { 0x00, 0x01, 0x05, 0x06, 0x0A };
+ u16 tmp = b43_radio_read16(dev, 0x001E);
+ int i, j;
+
+ for (i = 0; i < 5; i++) {
+ for (j = 0; j < 5; j++) {
+ if (tmp == (data_high[i] << 4 | data_low[j])) {
+ b43_phy_write(dev, 0x0069,
+ (i - j) << 8 | 0x00C0);
+ return;
+ }
+ }
+ }
+}
+
+int b43_radio_selectchannel(struct b43_wldev *dev,
+ u8 channel, int synthetic_pu_workaround)
+{
+ struct b43_phy *phy = &dev->phy;
+ u16 r8, tmp;
+ u16 freq;
+ u16 channelcookie;
+
+ /* First we set the channel radio code to prevent the
+ * firmware from sending ghost packets.
+ */
+ channelcookie = channel;
+ if (phy->type == B43_PHYTYPE_A)
+ channelcookie |= 0x100;
+ b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_CHAN, channelcookie);
+
+ if (phy->type == B43_PHYTYPE_A) {
+ if (channel > 200)
+ return -EINVAL;
+ freq = channel2freq_a(channel);
+
+ r8 = b43_radio_read16(dev, 0x0008);
+ b43_write16(dev, 0x03F0, freq);
+ b43_radio_write16(dev, 0x0008, r8);
+
+ //TODO: write max channel TX power? to Radio 0x2D
+ tmp = b43_radio_read16(dev, 0x002E);
+ tmp &= 0x0080;
+ //TODO: OR tmp with the Power out estimation for this channel?
+ b43_radio_write16(dev, 0x002E, tmp);
+
+ if (freq >= 4920 && freq <= 5500) {
+ /*
+ * r8 = (((freq * 15 * 0xE1FC780F) >> 32) / 29) & 0x0F;
+ * = (freq * 0.025862069
+ */
+ r8 = 3 * freq / 116; /* is equal to r8 = freq * 0.025862 */
+ }
+ b43_radio_write16(dev, 0x0007, (r8 << 4) | r8);
+ b43_radio_write16(dev, 0x0020, (r8 << 4) | r8);
+ b43_radio_write16(dev, 0x0021, (r8 << 4) | r8);
+ b43_radio_write16(dev, 0x0022, (b43_radio_read16(dev, 0x0022)
+ & 0x000F) | (r8 << 4));
+ b43_radio_write16(dev, 0x002A, (r8 << 4));
+ b43_radio_write16(dev, 0x002B, (r8 << 4));
+ b43_radio_write16(dev, 0x0008, (b43_radio_read16(dev, 0x0008)
+ & 0x00F0) | (r8 << 4));
+ b43_radio_write16(dev, 0x0029, (b43_radio_read16(dev, 0x0029)
+ & 0xFF0F) | 0x00B0);
+ b43_radio_write16(dev, 0x0035, 0x00AA);
+ b43_radio_write16(dev, 0x0036, 0x0085);
+ b43_radio_write16(dev, 0x003A, (b43_radio_read16(dev, 0x003A)
+ & 0xFF20) |
+ freq_r3A_value(freq));
+ b43_radio_write16(dev, 0x003D,
+ b43_radio_read16(dev, 0x003D) & 0x00FF);
+ b43_radio_write16(dev, 0x0081, (b43_radio_read16(dev, 0x0081)
+ & 0xFF7F) | 0x0080);
+ b43_radio_write16(dev, 0x0035,
+ b43_radio_read16(dev, 0x0035) & 0xFFEF);
+ b43_radio_write16(dev, 0x0035, (b43_radio_read16(dev, 0x0035)
+ & 0xFFEF) | 0x0010);
+ b43_radio_set_tx_iq(dev);
+ //TODO: TSSI2dbm workaround
+ b43_phy_xmitpower(dev); //FIXME correct?
+ } else {
+ if ((channel < 1) || (channel > 14))
+ return -EINVAL;
+
+ if (synthetic_pu_workaround)
+ b43_synth_pu_workaround(dev, channel);
+
+ b43_write16(dev, B43_MMIO_CHANNEL, channel2freq_bg(channel));
+
+ if (channel == 14) {
+ if (dev->dev->bus->sprom.r1.country_code ==
+ SSB_SPROM1CCODE_JAPAN)
+ b43_hf_write(dev,
+ b43_hf_read(dev) & ~B43_HF_ACPR);
+ else
+ b43_hf_write(dev,
+ b43_hf_read(dev) | B43_HF_ACPR);
+ b43_write16(dev, B43_MMIO_CHANNEL_EXT,
+ b43_read16(dev, B43_MMIO_CHANNEL_EXT)
+ | (1 << 11));
+ } else {
+ b43_write16(dev, B43_MMIO_CHANNEL_EXT,
+ b43_read16(dev, B43_MMIO_CHANNEL_EXT)
+ & 0xF7BF);
+ }
+ }
+
+ phy->channel = channel;
+ /* Wait for the radio to tune to the channel and stabilize. */
+ msleep(8);
+
+ return 0;
+}
+
+/* http://bcm-specs.sipsolutions.net/TX_Gain_Base_Band */
+static u16 b43_get_txgain_base_band(u16 txpower)
+{
+ u16 ret;
+
+ B43_WARN_ON(txpower > 63);
+
+ if (txpower >= 54)
+ ret = 2;
+ else if (txpower >= 49)
+ ret = 4;
+ else if (txpower >= 44)
+ ret = 5;
+ else
+ ret = 6;
+
+ return ret;
+}
+
+/* http://bcm-specs.sipsolutions.net/TX_Gain_Radio_Frequency_Power_Amplifier */
+static u16 b43_get_txgain_freq_power_amp(u16 txpower)
+{
+ u16 ret;
+
+ B43_WARN_ON(txpower > 63);
+
+ if (txpower >= 32)
+ ret = 0;
+ else if (txpower >= 25)
+ ret = 1;
+ else if (txpower >= 20)
+ ret = 2;
+ else if (txpower >= 12)
+ ret = 3;
+ else
+ ret = 4;
+
+ return ret;
+}
+
+/* http://bcm-specs.sipsolutions.net/TX_Gain_Digital_Analog_Converter */
+static u16 b43_get_txgain_dac(u16 txpower)
+{
+ u16 ret;
+
+ B43_WARN_ON(txpower > 63);
+
+ if (txpower >= 54)
+ ret = txpower - 53;
+ else if (txpower >= 49)
+ ret = txpower - 42;
+ else if (txpower >= 44)
+ ret = txpower - 37;
+ else if (txpower >= 32)
+ ret = txpower - 32;
+ else if (txpower >= 25)
+ ret = txpower - 20;
+ else if (txpower >= 20)
+ ret = txpower - 13;
+ else if (txpower >= 12)
+ ret = txpower - 8;
+ else
+ ret = txpower;
+
+ return ret;
+}
+
+static void b43_radio_set_txpower_a(struct b43_wldev *dev, u16 txpower)
+{
+ struct b43_phy *phy = &dev->phy;
+ u16 pamp, base, dac, t;
+
+ txpower = limit_value(txpower, 0, 63);
+
+ pamp = b43_get_txgain_freq_power_amp(txpower);
+ pamp <<= 5;
+ pamp &= 0x00E0;
+ b43_phy_write(dev, 0x0019, pamp);
+
+ base = b43_get_txgain_base_band(txpower);
+ base &= 0x000F;
+ b43_phy_write(dev, 0x0017, base | 0x0020);
+
+ t = b43_ofdmtab_read16(dev, 0x3000, 1);
+ t &= 0x0007;
+
+ dac = b43_get_txgain_dac(txpower);
+ dac <<= 3;
+ dac |= t;
+
+ b43_ofdmtab_write16(dev, 0x3000, 1, dac);
+
+ phy->txpwr_offset = txpower;
+
+ //TODO: FuncPlaceholder (Adjust BB loft cancel)
+}
+
+void b43_radio_turn_on(struct b43_wldev *dev)
+{
+ struct b43_phy *phy = &dev->phy;
+ int err;
+
+ might_sleep();
+
+ if (phy->radio_on)
+ return;
+
+ switch (phy->type) {
+ case B43_PHYTYPE_A:
+ b43_radio_write16(dev, 0x0004, 0x00C0);
+ b43_radio_write16(dev, 0x0005, 0x0008);
+ b43_phy_write(dev, 0x0010, b43_phy_read(dev, 0x0010) & 0xFFF7);
+ b43_phy_write(dev, 0x0011, b43_phy_read(dev, 0x0011) & 0xFFF7);
+ b43_radio_init2060(dev);
+ break;
+ case B43_PHYTYPE_B:
+ case B43_PHYTYPE_G:
+ b43_phy_write(dev, 0x0015, 0x8000);
+ b43_phy_write(dev, 0x0015, 0xCC00);
+ b43_phy_write(dev, 0x0015, (phy->gmode ? 0x00C0 : 0x0000));
+ err = b43_radio_selectchannel(dev, B43_DEFAULT_CHANNEL_BG, 1);
+ B43_WARN_ON(err);
+ break;
+ default:
+ B43_WARN_ON(1);
+ }
+ phy->radio_on = 1;
+ b43dbg(dev->wl, "Radio turned on\n");
+}
+
+void b43_radio_turn_off(struct b43_wldev *dev)
+{
+ struct b43_phy *phy = &dev->phy;
+
+ if (phy->type == B43_PHYTYPE_A) {
+ b43_radio_write16(dev, 0x0004, 0x00FF);
+ b43_radio_write16(dev, 0x0005, 0x00FB);
+ b43_phy_write(dev, 0x0010, b43_phy_read(dev, 0x0010) | 0x0008);
+ b43_phy_write(dev, 0x0011, b43_phy_read(dev, 0x0011) | 0x0008);
+ }
+ if (phy->type == B43_PHYTYPE_G && dev->dev->id.revision >= 5) {
+ b43_phy_write(dev, 0x0811, b43_phy_read(dev, 0x0811) | 0x008C);
+ b43_phy_write(dev, 0x0812, b43_phy_read(dev, 0x0812) & 0xFF73);
+ } else
+ b43_phy_write(dev, 0x0015, 0xAA00);
+ phy->radio_on = 0;
+ b43dbg(dev->wl, "Radio turned off\n");
+}
--- /dev/null
+#ifndef B43_PHY_H_
+#define B43_PHY_H_
+
+#include <linux/types.h>
+
+struct b43_wldev;
+struct b43_phy;
+
+/*** PHY Registers ***/
+
+/* Routing */
+#define B43_PHYROUTE_OFDM_GPHY 0x400
+#define B43_PHYROUTE_EXT_GPHY 0x800
+
+/* Base registers. */
+#define B43_PHY_BASE(reg) (reg)
+/* OFDM (A) registers of a G-PHY */
+#define B43_PHY_OFDM(reg) ((reg) | B43_PHYROUTE_OFDM_GPHY)
+/* Extended G-PHY registers */
+#define B43_PHY_EXTG(reg) ((reg) | B43_PHYROUTE_EXT_GPHY)
+
+/* OFDM (A) PHY Registers */
+#define B43_PHY_VERSION_OFDM B43_PHY_OFDM(0x00) /* Versioning register for A-PHY */
+#define B43_PHY_BBANDCFG B43_PHY_OFDM(0x01) /* Baseband config */
+#define B43_PHY_BBANDCFG_RXANT 0x180 /* RX Antenna selection */
+#define B43_PHY_BBANDCFG_RXANT_SHIFT 7
+#define B43_PHY_PWRDOWN B43_PHY_OFDM(0x03) /* Powerdown */
+#define B43_PHY_CRSTHRES1 B43_PHY_OFDM(0x06) /* CRS Threshold 1 */
+#define B43_PHY_LNAHPFCTL B43_PHY_OFDM(0x1C) /* LNA/HPF control */
+#define B43_PHY_ADIVRELATED B43_PHY_OFDM(0x27) /* FIXME rename */
+#define B43_PHY_CRS0 B43_PHY_OFDM(0x29)
+#define B43_PHY_ANTDWELL B43_PHY_OFDM(0x2B) /* Antenna dwell */
+#define B43_PHY_ANTDWELL_AUTODIV1 0x0100 /* Automatic RX diversity start antenna */
+#define B43_PHY_ENCORE B43_PHY_OFDM(0x49) /* "Encore" (RangeMax / BroadRange) */
+#define B43_PHY_ENCORE_EN 0x0200 /* Encore enable */
+#define B43_PHY_LMS B43_PHY_OFDM(0x55)
+#define B43_PHY_OFDM61 B43_PHY_OFDM(0x61) /* FIXME rename */
+#define B43_PHY_OFDM61_10 0x0010 /* FIXME rename */
+#define B43_PHY_IQBAL B43_PHY_OFDM(0x69) /* I/Q balance */
+#define B43_PHY_OTABLECTL B43_PHY_OFDM(0x72) /* OFDM table control (see below) */
+#define B43_PHY_OTABLEOFF 0x03FF /* OFDM table offset (see below) */
+#define B43_PHY_OTABLENR 0xFC00 /* OFDM table number (see below) */
+#define B43_PHY_OTABLENR_SHIFT 10
+#define B43_PHY_OTABLEI B43_PHY_OFDM(0x73) /* OFDM table data I */
+#define B43_PHY_OTABLEQ B43_PHY_OFDM(0x74) /* OFDM table data Q */
+#define B43_PHY_HPWR_TSSICTL B43_PHY_OFDM(0x78) /* Hardware power TSSI control */
+#define B43_PHY_NRSSITHRES B43_PHY_OFDM(0x8A) /* NRSSI threshold */
+#define B43_PHY_ANTWRSETT B43_PHY_OFDM(0x8C) /* Antenna WR settle */
+#define B43_PHY_ANTWRSETT_ARXDIV 0x2000 /* Automatic RX diversity enabled */
+#define B43_PHY_CLIPPWRDOWNT B43_PHY_OFDM(0x93) /* Clip powerdown threshold */
+#define B43_PHY_OFDM9B B43_PHY_OFDM(0x9B) /* FIXME rename */
+#define B43_PHY_N1P1GAIN B43_PHY_OFDM(0xA0)
+#define B43_PHY_P1P2GAIN B43_PHY_OFDM(0xA1)
+#define B43_PHY_N1N2GAIN B43_PHY_OFDM(0xA2)
+#define B43_PHY_CLIPTHRES B43_PHY_OFDM(0xA3)
+#define B43_PHY_CLIPN1P2THRES B43_PHY_OFDM(0xA4)
+#define B43_PHY_DIVSRCHIDX B43_PHY_OFDM(0xA8) /* Divider search gain/index */
+#define B43_PHY_CLIPP2THRES B43_PHY_OFDM(0xA9)
+#define B43_PHY_CLIPP3THRES B43_PHY_OFDM(0xAA)
+#define B43_PHY_DIVP1P2GAIN B43_PHY_OFDM(0xAB)
+#define B43_PHY_DIVSRCHGAINBACK B43_PHY_OFDM(0xAD) /* Divider search gain back */
+#define B43_PHY_DIVSRCHGAINCHNG B43_PHY_OFDM(0xAE) /* Divider search gain change */
+#define B43_PHY_CRSTHRES1_R1 B43_PHY_OFDM(0xC0) /* CRS Threshold 1 (rev 1 only) */
+#define B43_PHY_CRSTHRES2_R1 B43_PHY_OFDM(0xC1) /* CRS Threshold 2 (rev 1 only) */
+#define B43_PHY_TSSIP_LTBASE B43_PHY_OFDM(0x380) /* TSSI power lookup table base */
+#define B43_PHY_DC_LTBASE B43_PHY_OFDM(0x3A0) /* DC lookup table base */
+#define B43_PHY_GAIN_LTBASE B43_PHY_OFDM(0x3C0) /* Gain lookup table base */
+
+/* CCK (B) PHY Registers */
+#define B43_PHY_VERSION_CCK B43_PHY_BASE(0x00) /* Versioning register for B-PHY */
+#define B43_PHY_CCKBBANDCFG B43_PHY_BASE(0x01) /* Contains antenna 0/1 control bit */
+#define B43_PHY_PGACTL B43_PHY_BASE(0x15) /* PGA control */
+#define B43_PHY_PGACTL_LPF 0x1000 /* Low pass filter (?) */
+#define B43_PHY_PGACTL_LOWBANDW 0x0040 /* Low bandwidth flag */
+#define B43_PHY_PGACTL_UNKNOWN 0xEFA0
+#define B43_PHY_FBCTL1 B43_PHY_BASE(0x18) /* Frequency bandwidth control 1 */
+#define B43_PHY_ITSSI B43_PHY_BASE(0x29) /* Idle TSSI */
+#define B43_PHY_LO_LEAKAGE B43_PHY_BASE(0x2D) /* Measured LO leakage */
+#define B43_PHY_ENERGY B43_PHY_BASE(0x33) /* Energy */
+#define B43_PHY_SYNCCTL B43_PHY_BASE(0x35)
+#define B43_PHY_FBCTL2 B43_PHY_BASE(0x38) /* Frequency bandwidth control 2 */
+#define B43_PHY_DACCTL B43_PHY_BASE(0x60) /* DAC control */
+#define B43_PHY_RCCALOVER B43_PHY_BASE(0x78) /* RC calibration override */
+
+/* Extended G-PHY Registers */
+#define B43_PHY_CLASSCTL B43_PHY_EXTG(0x02) /* Classify control */
+#define B43_PHY_GTABCTL B43_PHY_EXTG(0x03) /* G-PHY table control (see below) */
+#define B43_PHY_GTABOFF 0x03FF /* G-PHY table offset (see below) */
+#define B43_PHY_GTABNR 0xFC00 /* G-PHY table number (see below) */
+#define B43_PHY_GTABNR_SHIFT 10
+#define B43_PHY_GTABDATA B43_PHY_EXTG(0x04) /* G-PHY table data */
+#define B43_PHY_LO_MASK B43_PHY_EXTG(0x0F) /* Local Oscillator control mask */
+#define B43_PHY_LO_CTL B43_PHY_EXTG(0x10) /* Local Oscillator control */
+#define B43_PHY_RFOVER B43_PHY_EXTG(0x11) /* RF override */
+#define B43_PHY_RFOVERVAL B43_PHY_EXTG(0x12) /* RF override value */
+#define B43_PHY_RFOVERVAL_EXTLNA 0x8000
+#define B43_PHY_RFOVERVAL_LNA 0x7000
+#define B43_PHY_RFOVERVAL_LNA_SHIFT 12
+#define B43_PHY_RFOVERVAL_PGA 0x0F00
+#define B43_PHY_RFOVERVAL_PGA_SHIFT 8
+#define B43_PHY_RFOVERVAL_UNK 0x0010 /* Unknown, always set. */
+#define B43_PHY_RFOVERVAL_TRSWRX 0x00E0
+#define B43_PHY_RFOVERVAL_BW 0x0003 /* Bandwidth flags */
+#define B43_PHY_RFOVERVAL_BW_LPF 0x0001 /* Low Pass Filter */
+#define B43_PHY_RFOVERVAL_BW_LBW 0x0002 /* Low Bandwidth (when set), high when unset */
+#define B43_PHY_ANALOGOVER B43_PHY_EXTG(0x14) /* Analog override */
+#define B43_PHY_ANALOGOVERVAL B43_PHY_EXTG(0x15) /* Analog override value */
+
+/*** OFDM table numbers ***/
+#define B43_OFDMTAB(number, offset) (((number) << B43_PHY_OTABLENR_SHIFT) | (offset))
+#define B43_OFDMTAB_AGC1 B43_OFDMTAB(0x00, 0)
+#define B43_OFDMTAB_GAIN0 B43_OFDMTAB(0x00, 0)
+#define B43_OFDMTAB_GAINX B43_OFDMTAB(0x01, 0) //TODO rename
+#define B43_OFDMTAB_GAIN1 B43_OFDMTAB(0x01, 4)
+#define B43_OFDMTAB_AGC3 B43_OFDMTAB(0x02, 0)
+#define B43_OFDMTAB_GAIN2 B43_OFDMTAB(0x02, 3)
+#define B43_OFDMTAB_LNAHPFGAIN1 B43_OFDMTAB(0x03, 0)
+#define B43_OFDMTAB_WRSSI B43_OFDMTAB(0x04, 0)
+#define B43_OFDMTAB_LNAHPFGAIN2 B43_OFDMTAB(0x04, 0)
+#define B43_OFDMTAB_NOISESCALE B43_OFDMTAB(0x05, 0)
+#define B43_OFDMTAB_AGC2 B43_OFDMTAB(0x06, 0)
+#define B43_OFDMTAB_ROTOR B43_OFDMTAB(0x08, 0)
+#define B43_OFDMTAB_ADVRETARD B43_OFDMTAB(0x09, 0)
+#define B43_OFDMTAB_DAC B43_OFDMTAB(0x0C, 0)
+#define B43_OFDMTAB_DC B43_OFDMTAB(0x0E, 7)
+#define B43_OFDMTAB_PWRDYN2 B43_OFDMTAB(0x0E, 12)
+#define B43_OFDMTAB_LNAGAIN B43_OFDMTAB(0x0E, 13)
+//TODO
+#define B43_OFDMTAB_LPFGAIN B43_OFDMTAB(0x0F, 12)
+#define B43_OFDMTAB_RSSI B43_OFDMTAB(0x10, 0)
+//TODO
+#define B43_OFDMTAB_AGC1_R1 B43_OFDMTAB(0x13, 0)
+#define B43_OFDMTAB_GAINX_R1 B43_OFDMTAB(0x14, 0) //TODO rename
+#define B43_OFDMTAB_MINSIGSQ B43_OFDMTAB(0x14, 1)
+#define B43_OFDMTAB_AGC3_R1 B43_OFDMTAB(0x15, 0)
+#define B43_OFDMTAB_WRSSI_R1 B43_OFDMTAB(0x15, 4)
+#define B43_OFDMTAB_TSSI B43_OFDMTAB(0x15, 0)
+#define B43_OFDMTAB_DACRFPABB B43_OFDMTAB(0x16, 0)
+#define B43_OFDMTAB_DACOFF B43_OFDMTAB(0x17, 0)
+#define B43_OFDMTAB_DCBIAS B43_OFDMTAB(0x18, 0)
+
+u16 b43_ofdmtab_read16(struct b43_wldev *dev, u16 table, u16 offset);
+void b43_ofdmtab_write16(struct b43_wldev *dev, u16 table,
+ u16 offset, u16 value);
+u32 b43_ofdmtab_read32(struct b43_wldev *dev, u16 table, u16 offset);
+void b43_ofdmtab_write32(struct b43_wldev *dev, u16 table,
+ u16 offset, u32 value);
+
+/*** G-PHY table numbers */
+#define B43_GTAB(number, offset) (((number) << B43_PHY_GTABNR_SHIFT) | (offset))
+#define B43_GTAB_NRSSI B43_GTAB(0x00, 0)
+#define B43_GTAB_TRFEMW B43_GTAB(0x0C, 0x120)
+#define B43_GTAB_ORIGTR B43_GTAB(0x2E, 0x298)
+
+u16 b43_gtab_read(struct b43_wldev *dev, u16 table, u16 offset); //TODO implement
+void b43_gtab_write(struct b43_wldev *dev, u16 table, u16 offset, u16 value); //TODO implement
+
+#define B43_DEFAULT_CHANNEL_A 36
+#define B43_DEFAULT_CHANNEL_BG 6
+
+enum {
+ B43_ANTENNA0, /* Antenna 0 */
+ B43_ANTENNA1, /* Antenna 0 */
+ B43_ANTENNA_AUTO1, /* Automatic, starting with antenna 1 */
+ B43_ANTENNA_AUTO0, /* Automatic, starting with antenna 0 */
+
+ B43_ANTENNA_AUTO = B43_ANTENNA_AUTO0,
+ B43_ANTENNA_DEFAULT = B43_ANTENNA_AUTO,
+};
+
+enum {
+ B43_INTERFMODE_NONE,
+ B43_INTERFMODE_NONWLAN,
+ B43_INTERFMODE_MANUALWLAN,
+ B43_INTERFMODE_AUTOWLAN,
+};
+
+/* Masks for the different PHY versioning registers. */
+#define B43_PHYVER_ANALOG 0xF000
+#define B43_PHYVER_ANALOG_SHIFT 12
+#define B43_PHYVER_TYPE 0x0F00
+#define B43_PHYVER_TYPE_SHIFT 8
+#define B43_PHYVER_VERSION 0x00FF
+
+void b43_raw_phy_lock(struct b43_wldev *dev);
+#define b43_phy_lock(dev, flags) \
+ do { \
+ local_irq_save(flags); \
+ b43_raw_phy_lock(dev); \
+ } while (0)
+void b43_raw_phy_unlock(struct b43_wldev *dev);
+#define b43_phy_unlock(dev, flags) \
+ do { \
+ b43_raw_phy_unlock(dev); \
+ local_irq_restore(flags); \
+ } while (0)
+
+u16 b43_phy_read(struct b43_wldev *dev, u16 offset);
+void b43_phy_write(struct b43_wldev *dev, u16 offset, u16 val);
+
+int b43_phy_init_tssi2dbm_table(struct b43_wldev *dev);
+
+void b43_phy_early_init(struct b43_wldev *dev);
+int b43_phy_init(struct b43_wldev *dev);
+
+void b43_set_rx_antenna(struct b43_wldev *dev, int antenna);
+
+void b43_phy_xmitpower(struct b43_wldev *dev);
+void b43_gphy_dc_lt_init(struct b43_wldev *dev);
+
+/* Returns the boolean whether the board has HardwarePowerControl */
+bool b43_has_hardware_pctl(struct b43_phy *phy);
+/* Returns the boolean whether "TX Magnification" is enabled. */
+#define has_tx_magnification(phy) \
+ (((phy)->rev >= 2) && \
+ ((phy)->radio_ver == 0x2050) && \
+ ((phy)->radio_rev == 8))
+/* Card uses the loopback gain stuff */
+#define has_loopback_gain(phy) \
+ (((phy)->rev > 1) || ((phy)->gmode))
+
+/* Radio Attenuation (RF Attenuation) */
+struct b43_rfatt {
+ u8 att; /* Attenuation value */
+ bool with_padmix; /* Flag, PAD Mixer enabled. */
+};
+struct b43_rfatt_list {
+ /* Attenuation values list */
+ const struct b43_rfatt *list;
+ u8 len;
+ /* Minimum/Maximum attenuation values */
+ u8 min_val;
+ u8 max_val;
+};
+
+/* Baseband Attenuation */
+struct b43_bbatt {
+ u8 att; /* Attenuation value */
+};
+struct b43_bbatt_list {
+ /* Attenuation values list */
+ const struct b43_bbatt *list;
+ u8 len;
+ /* Minimum/Maximum attenuation values */
+ u8 min_val;
+ u8 max_val;
+};
+
+/* tx_control bits. */
+#define B43_TXCTL_PA3DB 0x40 /* PA Gain 3dB */
+#define B43_TXCTL_PA2DB 0x20 /* PA Gain 2dB */
+#define B43_TXCTL_TXMIX 0x10 /* TX Mixer Gain */
+
+/* Write BasebandAttenuation value to the device. */
+void b43_phy_set_baseband_attenuation(struct b43_wldev *dev,
+ u16 baseband_attenuation);
+
+extern const u8 b43_radio_channel_codes_bg[];
+
+void b43_radio_lock(struct b43_wldev *dev);
+void b43_radio_unlock(struct b43_wldev *dev);
+
+u16 b43_radio_read16(struct b43_wldev *dev, u16 offset);
+void b43_radio_write16(struct b43_wldev *dev, u16 offset, u16 val);
+
+u16 b43_radio_init2050(struct b43_wldev *dev);
+void b43_radio_init2060(struct b43_wldev *dev);
+
+void b43_radio_turn_on(struct b43_wldev *dev);
+void b43_radio_turn_off(struct b43_wldev *dev);
+
+int b43_radio_selectchannel(struct b43_wldev *dev, u8 channel,
+ int synthetic_pu_workaround);
+
+u8 b43_radio_aci_detect(struct b43_wldev *dev, u8 channel);
+u8 b43_radio_aci_scan(struct b43_wldev *dev);
+
+int b43_radio_set_interference_mitigation(struct b43_wldev *dev, int mode);
+
+void b43_calc_nrssi_slope(struct b43_wldev *dev);
+void b43_calc_nrssi_threshold(struct b43_wldev *dev);
+s16 b43_nrssi_hw_read(struct b43_wldev *dev, u16 offset);
+void b43_nrssi_hw_write(struct b43_wldev *dev, u16 offset, s16 val);
+void b43_nrssi_hw_update(struct b43_wldev *dev, u16 val);
+void b43_nrssi_mem_update(struct b43_wldev *dev);
+
+void b43_radio_set_tx_iq(struct b43_wldev *dev);
+u16 b43_radio_calibrationvalue(struct b43_wldev *dev);
+
+void b43_put_attenuation_into_ranges(struct b43_wldev *dev,
+ int *_bbatt, int *_rfatt);
+
+void b43_set_txpower_g(struct b43_wldev *dev,
+ const struct b43_bbatt *bbatt,
+ const struct b43_rfatt *rfatt, u8 tx_control);
+
+#endif /* B43_PHY_H_ */
--- /dev/null
+/*
+
+ Broadcom B43 wireless driver
+
+ PIO Transmission
+
+ Copyright (c) 2005 Michael Buesch <mb@bu3sch.de>
+
+ This program is free software; you can redistribute it and/or modify
+ it under the terms of the GNU General Public License as published by
+ the Free Software Foundation; either version 2 of the License, or
+ (at your option) any later version.
+
+ This program is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ GNU General Public License for more details.
+
+ You should have received a copy of the GNU General Public License
+ along with this program; see the file COPYING. If not, write to
+ the Free Software Foundation, Inc., 51 Franklin Steet, Fifth Floor,
+ Boston, MA 02110-1301, USA.
+
+*/
+
+#include "b43.h"
+#include "pio.h"
+#include "main.h"
+#include "xmit.h"
+
+#include <linux/delay.h>
+
+static void tx_start(struct b43_pioqueue *queue)
+{
+ b43_pio_write(queue, B43_PIO_TXCTL, B43_PIO_TXCTL_INIT);
+}
+
+static void tx_octet(struct b43_pioqueue *queue, u8 octet)
+{
+ if (queue->need_workarounds) {
+ b43_pio_write(queue, B43_PIO_TXDATA, octet);
+ b43_pio_write(queue, B43_PIO_TXCTL, B43_PIO_TXCTL_WRITELO);
+ } else {
+ b43_pio_write(queue, B43_PIO_TXCTL, B43_PIO_TXCTL_WRITELO);
+ b43_pio_write(queue, B43_PIO_TXDATA, octet);
+ }
+}
+
+static u16 tx_get_next_word(const u8 * txhdr,
+ const u8 * packet,
+ size_t txhdr_size, unsigned int *pos)
+{
+ const u8 *source;
+ unsigned int i = *pos;
+ u16 ret;
+
+ if (i < txhdr_size) {
+ source = txhdr;
+ } else {
+ source = packet;
+ i -= txhdr_size;
+ }
+ ret = le16_to_cpu(*((u16 *) (source + i)));
+ *pos += 2;
+
+ return ret;
+}
+
+static void tx_data(struct b43_pioqueue *queue,
+ u8 * txhdr, const u8 * packet, unsigned int octets)
+{
+ u16 data;
+ unsigned int i = 0;
+
+ if (queue->need_workarounds) {
+ data = tx_get_next_word(txhdr, packet,
+ sizeof(struct b43_txhdr_fw4), &i);
+ b43_pio_write(queue, B43_PIO_TXDATA, data);
+ }
+ b43_pio_write(queue, B43_PIO_TXCTL,
+ B43_PIO_TXCTL_WRITELO | B43_PIO_TXCTL_WRITEHI);
+ while (i < octets - 1) {
+ data = tx_get_next_word(txhdr, packet,
+ sizeof(struct b43_txhdr_fw4), &i);
+ b43_pio_write(queue, B43_PIO_TXDATA, data);
+ }
+ if (octets % 2)
+ tx_octet(queue,
+ packet[octets - sizeof(struct b43_txhdr_fw4) - 1]);
+}
+
+static void tx_complete(struct b43_pioqueue *queue, struct sk_buff *skb)
+{
+ if (queue->need_workarounds) {
+ b43_pio_write(queue, B43_PIO_TXDATA, skb->data[skb->len - 1]);
+ b43_pio_write(queue, B43_PIO_TXCTL,
+ B43_PIO_TXCTL_WRITELO | B43_PIO_TXCTL_COMPLETE);
+ } else {
+ b43_pio_write(queue, B43_PIO_TXCTL, B43_PIO_TXCTL_COMPLETE);
+ }
+}
+
+static u16 generate_cookie(struct b43_pioqueue *queue,
+ struct b43_pio_txpacket *packet)
+{
+ u16 cookie = 0x0000;
+ int packetindex;
+
+ /* We use the upper 4 bits for the PIO
+ * controller ID and the lower 12 bits
+ * for the packet index (in the cache).
+ */
+ switch (queue->mmio_base) {
+ case B43_MMIO_PIO1_BASE:
+ break;
+ case B43_MMIO_PIO2_BASE:
+ cookie = 0x1000;
+ break;
+ case B43_MMIO_PIO3_BASE:
+ cookie = 0x2000;
+ break;
+ case B43_MMIO_PIO4_BASE:
+ cookie = 0x3000;
+ break;
+ default:
+ B43_WARN_ON(1);
+ }
+ packetindex = pio_txpacket_getindex(packet);
+ B43_WARN_ON(packetindex & ~0x0FFF);
+ cookie |= (u16) packetindex;
+
+ return cookie;
+}
+
+static
+struct b43_pioqueue *parse_cookie(struct b43_wldev *dev,
+ u16 cookie, struct b43_pio_txpacket **packet)
+{
+ struct b43_pio *pio = &dev->pio;
+ struct b43_pioqueue *queue = NULL;
+ int packetindex;
+
+ switch (cookie & 0xF000) {
+ case 0x0000:
+ queue = pio->queue0;
+ break;
+ case 0x1000:
+ queue = pio->queue1;
+ break;
+ case 0x2000:
+ queue = pio->queue2;
+ break;
+ case 0x3000:
+ queue = pio->queue3;
+ break;
+ default:
+ B43_WARN_ON(1);
+ }
+ packetindex = (cookie & 0x0FFF);
+ B43_WARN_ON(!(packetindex >= 0 && packetindex < B43_PIO_MAXTXPACKETS));
+ *packet = &(queue->tx_packets_cache[packetindex]);
+
+ return queue;
+}
+
+union txhdr_union {
+ struct b43_txhdr_fw4 txhdr_fw4;
+};
+
+static void pio_tx_write_fragment(struct b43_pioqueue *queue,
+ struct sk_buff *skb,
+ struct b43_pio_txpacket *packet,
+ size_t txhdr_size)
+{
+ union txhdr_union txhdr_data;
+ u8 *txhdr = NULL;
+ unsigned int octets;
+
+ txhdr = (u8 *) (&txhdr_data.txhdr_fw4);
+
+ B43_WARN_ON(skb_shinfo(skb)->nr_frags);
+ b43_generate_txhdr(queue->dev,
+ txhdr, skb->data, skb->len,
+ &packet->txstat.control,
+ generate_cookie(queue, packet));
+
+ tx_start(queue);
+ octets = skb->len + txhdr_size;
+ if (queue->need_workarounds)
+ octets--;
+ tx_data(queue, txhdr, (u8 *) skb->data, octets);
+ tx_complete(queue, skb);
+}
+
+static void free_txpacket(struct b43_pio_txpacket *packet)
+{
+ struct b43_pioqueue *queue = packet->queue;
+
+ if (packet->skb)
+ dev_kfree_skb_any(packet->skb);
+ list_move(&packet->list, &queue->txfree);
+ queue->nr_txfree++;
+}
+
+static int pio_tx_packet(struct b43_pio_txpacket *packet)
+{
+ struct b43_pioqueue *queue = packet->queue;
+ struct sk_buff *skb = packet->skb;
+ u16 octets;
+
+ octets = (u16) skb->len + sizeof(struct b43_txhdr_fw4);
+ if (queue->tx_devq_size < octets) {
+ b43warn(queue->dev->wl, "PIO queue too small. "
+ "Dropping packet.\n");
+ /* Drop it silently (return success) */
+ free_txpacket(packet);
+ return 0;
+ }
+ B43_WARN_ON(queue->tx_devq_packets > B43_PIO_MAXTXDEVQPACKETS);
+ B43_WARN_ON(queue->tx_devq_used > queue->tx_devq_size);
+ /* Check if there is sufficient free space on the device
+ * TX queue. If not, return and let the TX tasklet
+ * retry later.
+ */
+ if (queue->tx_devq_packets == B43_PIO_MAXTXDEVQPACKETS)
+ return -EBUSY;
+ if (queue->tx_devq_used + octets > queue->tx_devq_size)
+ return -EBUSY;
+ /* Now poke the device. */
+ pio_tx_write_fragment(queue, skb, packet, sizeof(struct b43_txhdr_fw4));
+
+ /* Account for the packet size.
+ * (We must not overflow the device TX queue)
+ */
+ queue->tx_devq_packets++;
+ queue->tx_devq_used += octets;
+
+ /* Transmission started, everything ok, move the
+ * packet to the txrunning list.
+ */
+ list_move_tail(&packet->list, &queue->txrunning);
+
+ return 0;
+}
+
+static void tx_tasklet(unsigned long d)
+{
+ struct b43_pioqueue *queue = (struct b43_pioqueue *)d;
+ struct b43_wldev *dev = queue->dev;
+ unsigned long flags;
+ struct b43_pio_txpacket *packet, *tmp_packet;
+ int err;
+ u16 txctl;
+
+ spin_lock_irqsave(&dev->wl->irq_lock, flags);
+ if (queue->tx_frozen)
+ goto out_unlock;
+ txctl = b43_pio_read(queue, B43_PIO_TXCTL);
+ if (txctl & B43_PIO_TXCTL_SUSPEND)
+ goto out_unlock;
+
+ list_for_each_entry_safe(packet, tmp_packet, &queue->txqueue, list) {
+ /* Try to transmit the packet. This can fail, if
+ * the device queue is full. In case of failure, the
+ * packet is left in the txqueue.
+ * If transmission succeed, the packet is moved to txrunning.
+ * If it is impossible to transmit the packet, it
+ * is dropped.
+ */
+ err = pio_tx_packet(packet);
+ if (err)
+ break;
+ }
+ out_unlock:
+ spin_unlock_irqrestore(&dev->wl->irq_lock, flags);
+}
+
+static void setup_txqueues(struct b43_pioqueue *queue)
+{
+ struct b43_pio_txpacket *packet;
+ int i;
+
+ queue->nr_txfree = B43_PIO_MAXTXPACKETS;
+ for (i = 0; i < B43_PIO_MAXTXPACKETS; i++) {
+ packet = &(queue->tx_packets_cache[i]);
+
+ packet->queue = queue;
+ INIT_LIST_HEAD(&packet->list);
+
+ list_add(&packet->list, &queue->txfree);
+ }
+}
+
+static
+struct b43_pioqueue *b43_setup_pioqueue(struct b43_wldev *dev,
+ u16 pio_mmio_base)
+{
+ struct b43_pioqueue *queue;
+ u16 qsize;
+
+ queue = kzalloc(sizeof(*queue), GFP_KERNEL);
+ if (!queue)
+ goto out;
+
+ queue->dev = dev;
+ queue->mmio_base = pio_mmio_base;
+ queue->need_workarounds = (dev->dev->id.revision < 3);
+
+ INIT_LIST_HEAD(&queue->txfree);
+ INIT_LIST_HEAD(&queue->txqueue);
+ INIT_LIST_HEAD(&queue->txrunning);
+ tasklet_init(&queue->txtask, tx_tasklet, (unsigned long)queue);
+
+ b43_write32(dev, B43_MMIO_MACCTL, b43_read32(dev, B43_MMIO_MACCTL)
+ & ~B43_MACCTL_BE);
+
+ qsize = b43_read16(dev, queue->mmio_base + B43_PIO_TXQBUFSIZE);
+ if (qsize == 0) {
+ b43err(dev->wl, "This card does not support PIO "
+ "operation mode. Please use DMA mode "
+ "(module parameter pio=0).\n");
+ goto err_freequeue;
+ }
+ if (qsize <= B43_PIO_TXQADJUST) {
+ b43err(dev->wl, "PIO tx device-queue too small (%u)\n", qsize);
+ goto err_freequeue;
+ }
+ qsize -= B43_PIO_TXQADJUST;
+ queue->tx_devq_size = qsize;
+
+ setup_txqueues(queue);
+
+ out:
+ return queue;
+
+ err_freequeue:
+ kfree(queue);
+ queue = NULL;
+ goto out;
+}
+
+static void cancel_transfers(struct b43_pioqueue *queue)
+{
+ struct b43_pio_txpacket *packet, *tmp_packet;
+
+ tasklet_disable(&queue->txtask);
+
+ list_for_each_entry_safe(packet, tmp_packet, &queue->txrunning, list)
+ free_txpacket(packet);
+ list_for_each_entry_safe(packet, tmp_packet, &queue->txqueue, list)
+ free_txpacket(packet);
+}
+
+static void b43_destroy_pioqueue(struct b43_pioqueue *queue)
+{
+ if (!queue)
+ return;
+
+ cancel_transfers(queue);
+ kfree(queue);
+}
+
+void b43_pio_free(struct b43_wldev *dev)
+{
+ struct b43_pio *pio;
+
+ if (!b43_using_pio(dev))
+ return;
+ pio = &dev->pio;
+
+ b43_destroy_pioqueue(pio->queue3);
+ pio->queue3 = NULL;
+ b43_destroy_pioqueue(pio->queue2);
+ pio->queue2 = NULL;
+ b43_destroy_pioqueue(pio->queue1);
+ pio->queue1 = NULL;
+ b43_destroy_pioqueue(pio->queue0);
+ pio->queue0 = NULL;
+}
+
+int b43_pio_init(struct b43_wldev *dev)
+{
+ struct b43_pio *pio = &dev->pio;
+ struct b43_pioqueue *queue;
+ int err = -ENOMEM;
+
+ queue = b43_setup_pioqueue(dev, B43_MMIO_PIO1_BASE);
+ if (!queue)
+ goto out;
+ pio->queue0 = queue;
+
+ queue = b43_setup_pioqueue(dev, B43_MMIO_PIO2_BASE);
+ if (!queue)
+ goto err_destroy0;
+ pio->queue1 = queue;
+
+ queue = b43_setup_pioqueue(dev, B43_MMIO_PIO3_BASE);
+ if (!queue)
+ goto err_destroy1;
+ pio->queue2 = queue;
+
+ queue = b43_setup_pioqueue(dev, B43_MMIO_PIO4_BASE);
+ if (!queue)
+ goto err_destroy2;
+ pio->queue3 = queue;
+
+ if (dev->dev->id.revision < 3)
+ dev->irq_savedstate |= B43_IRQ_PIO_WORKAROUND;
+
+ b43dbg(dev->wl, "PIO initialized\n");
+ err = 0;
+ out:
+ return err;
+
+ err_destroy2:
+ b43_destroy_pioqueue(pio->queue2);
+ pio->queue2 = NULL;
+ err_destroy1:
+ b43_destroy_pioqueue(pio->queue1);
+ pio->queue1 = NULL;
+ err_destroy0:
+ b43_destroy_pioqueue(pio->queue0);
+ pio->queue0 = NULL;
+ goto out;
+}
+
+int b43_pio_tx(struct b43_wldev *dev,
+ struct sk_buff *skb, struct ieee80211_tx_control *ctl)
+{
+ struct b43_pioqueue *queue = dev->pio.queue1;
+ struct b43_pio_txpacket *packet;
+
+ B43_WARN_ON(queue->tx_suspended);
+ B43_WARN_ON(list_empty(&queue->txfree));
+
+ packet = list_entry(queue->txfree.next, struct b43_pio_txpacket, list);
+ packet->skb = skb;
+
+ memset(&packet->txstat, 0, sizeof(packet->txstat));
+ memcpy(&packet->txstat.control, ctl, sizeof(*ctl));
+
+ list_move_tail(&packet->list, &queue->txqueue);
+ queue->nr_txfree--;
+ queue->nr_tx_packets++;
+ B43_WARN_ON(queue->nr_txfree >= B43_PIO_MAXTXPACKETS);
+
+ tasklet_schedule(&queue->txtask);
+
+ return 0;
+}
+
+void b43_pio_handle_txstatus(struct b43_wldev *dev,
+ const struct b43_txstatus *status)
+{
+ struct b43_pioqueue *queue;
+ struct b43_pio_txpacket *packet;
+
+ queue = parse_cookie(dev, status->cookie, &packet);
+ if (B43_WARN_ON(!queue))
+ return;
+
+ queue->tx_devq_packets--;
+ queue->tx_devq_used -=
+ (packet->skb->len + sizeof(struct b43_txhdr_fw4));
+
+ if (status->acked) {
+ packet->txstat.flags |= IEEE80211_TX_STATUS_ACK;
+ } else {
+ if (!(packet->txstat.control.flags & IEEE80211_TXCTL_NO_ACK))
+ packet->txstat.excessive_retries = 1;
+ }
+ if (status->frame_count == 0) {
+ /* The frame was not transmitted at all. */
+ packet->txstat.retry_count = 0;
+ } else
+ packet->txstat.retry_count = status->frame_count - 1;
+ ieee80211_tx_status_irqsafe(dev->wl->hw, packet->skb,
+ &(packet->txstat));
+ packet->skb = NULL;
+
+ free_txpacket(packet);
+ /* If there are packets on the txqueue, poke the tasklet
+ * to transmit them.
+ */
+ if (!list_empty(&queue->txqueue))
+ tasklet_schedule(&queue->txtask);
+}
+
+void b43_pio_get_tx_stats(struct b43_wldev *dev,
+ struct ieee80211_tx_queue_stats *stats)
+{
+ struct b43_pio *pio = &dev->pio;
+ struct b43_pioqueue *queue;
+ struct ieee80211_tx_queue_stats_data *data;
+
+ queue = pio->queue1;
+ data = &(stats->data[0]);
+ data->len = B43_PIO_MAXTXPACKETS - queue->nr_txfree;
+ data->limit = B43_PIO_MAXTXPACKETS;
+ data->count = queue->nr_tx_packets;
+}
+
+static void pio_rx_error(struct b43_pioqueue *queue,
+ int clear_buffers, const char *error)
+{
+ int i;
+
+ b43err(queue->dev->wl, "PIO RX error: %s\n", error);
+ b43_pio_write(queue, B43_PIO_RXCTL, B43_PIO_RXCTL_READY);
+ if (clear_buffers) {
+ B43_WARN_ON(queue->mmio_base != B43_MMIO_PIO1_BASE);
+ for (i = 0; i < 15; i++) {
+ /* Dummy read. */
+ b43_pio_read(queue, B43_PIO_RXDATA);
+ }
+ }
+}
+
+void b43_pio_rx(struct b43_pioqueue *queue)
+{
+ u16 preamble[21] = { 0 };
+ struct b43_rxhdr_fw4 *rxhdr;
+ u16 tmp, len, macstat;
+ int i, preamble_readwords;
+ struct sk_buff *skb;
+
+ tmp = b43_pio_read(queue, B43_PIO_RXCTL);
+ if (!(tmp & B43_PIO_RXCTL_DATAAVAILABLE))
+ return;
+ b43_pio_write(queue, B43_PIO_RXCTL, B43_PIO_RXCTL_DATAAVAILABLE);
+
+ for (i = 0; i < 10; i++) {
+ tmp = b43_pio_read(queue, B43_PIO_RXCTL);
+ if (tmp & B43_PIO_RXCTL_READY)
+ goto data_ready;
+ udelay(10);
+ }
+ b43dbg(queue->dev->wl, "PIO RX timed out\n");
+ return;
+ data_ready:
+
+ len = b43_pio_read(queue, B43_PIO_RXDATA);
+ if (unlikely(len > 0x700)) {
+ pio_rx_error(queue, 0, "len > 0x700");
+ return;
+ }
+ if (unlikely(len == 0 && queue->mmio_base != B43_MMIO_PIO4_BASE)) {
+ pio_rx_error(queue, 0, "len == 0");
+ return;
+ }
+ preamble[0] = cpu_to_le16(len);
+ if (queue->mmio_base == B43_MMIO_PIO4_BASE)
+ preamble_readwords = 14 / sizeof(u16);
+ else
+ preamble_readwords = 18 / sizeof(u16);
+ for (i = 0; i < preamble_readwords; i++) {
+ tmp = b43_pio_read(queue, B43_PIO_RXDATA);
+ preamble[i + 1] = cpu_to_le16(tmp);
+ }
+ rxhdr = (struct b43_rxhdr_fw4 *)preamble;
+ macstat = le16_to_cpu(rxhdr->mac_status);
+ if (macstat & B43_RX_MAC_FCSERR) {
+ pio_rx_error(queue,
+ (queue->mmio_base == B43_MMIO_PIO1_BASE),
+ "Frame FCS error");
+ return;
+ }
+ if (queue->mmio_base == B43_MMIO_PIO4_BASE) {
+ /* We received an xmit status. */
+ struct b43_hwtxstatus *hw;
+
+ hw = (struct b43_hwtxstatus *)(preamble + 1);
+ b43_handle_hwtxstatus(queue->dev, hw);
+
+ return;
+ }
+
+ skb = dev_alloc_skb(len);
+ if (unlikely(!skb)) {
+ pio_rx_error(queue, 1, "OOM");
+ return;
+ }
+ skb_put(skb, len);
+ for (i = 0; i < len - 1; i += 2) {
+ tmp = b43_pio_read(queue, B43_PIO_RXDATA);
+ *((u16 *) (skb->data + i)) = cpu_to_le16(tmp);
+ }
+ if (len % 2) {
+ tmp = b43_pio_read(queue, B43_PIO_RXDATA);
+ skb->data[len - 1] = (tmp & 0x00FF);
+/* The specs say the following is required, but
+ * it is wrong and corrupts the PLCP. If we don't do
+ * this, the PLCP seems to be correct. So ifdef it out for now.
+ */
+#if 0
+ if (rxflags2 & B43_RXHDR_FLAGS2_TYPE2FRAME)
+ skb->data[2] = (tmp & 0xFF00) >> 8;
+ else
+ skb->data[0] = (tmp & 0xFF00) >> 8;
+#endif
+ }
+ b43_rx(queue->dev, skb, rxhdr);
+}
+
+void b43_pio_tx_suspend(struct b43_pioqueue *queue)
+{
+ b43_power_saving_ctl_bits(queue->dev, B43_PS_AWAKE);
+ b43_pio_write(queue, B43_PIO_TXCTL, b43_pio_read(queue, B43_PIO_TXCTL)
+ | B43_PIO_TXCTL_SUSPEND);
+}
+
+void b43_pio_tx_resume(struct b43_pioqueue *queue)
+{
+ b43_pio_write(queue, B43_PIO_TXCTL, b43_pio_read(queue, B43_PIO_TXCTL)
+ & ~B43_PIO_TXCTL_SUSPEND);
+ b43_power_saving_ctl_bits(queue->dev, 0);
+ tasklet_schedule(&queue->txtask);
+}
+
+void b43_pio_freeze_txqueues(struct b43_wldev *dev)
+{
+ struct b43_pio *pio;
+
+ B43_WARN_ON(!b43_using_pio(dev));
+ pio = &dev->pio;
+ pio->queue0->tx_frozen = 1;
+ pio->queue1->tx_frozen = 1;
+ pio->queue2->tx_frozen = 1;
+ pio->queue3->tx_frozen = 1;
+}
+
+void b43_pio_thaw_txqueues(struct b43_wldev *dev)
+{
+ struct b43_pio *pio;
+
+ B43_WARN_ON(!b43_using_pio(dev));
+ pio = &dev->pio;
+ pio->queue0->tx_frozen = 0;
+ pio->queue1->tx_frozen = 0;
+ pio->queue2->tx_frozen = 0;
+ pio->queue3->tx_frozen = 0;
+ if (!list_empty(&pio->queue0->txqueue))
+ tasklet_schedule(&pio->queue0->txtask);
+ if (!list_empty(&pio->queue1->txqueue))
+ tasklet_schedule(&pio->queue1->txtask);
+ if (!list_empty(&pio->queue2->txqueue))
+ tasklet_schedule(&pio->queue2->txtask);
+ if (!list_empty(&pio->queue3->txqueue))
+ tasklet_schedule(&pio->queue3->txtask);
+}
--- /dev/null
+#ifndef B43_PIO_H_
+#define B43_PIO_H_
+
+#include "b43.h"
+
+#include <linux/interrupt.h>
+#include <linux/list.h>
+#include <linux/skbuff.h>
+
+#define B43_PIO_TXCTL 0x00
+#define B43_PIO_TXDATA 0x02
+#define B43_PIO_TXQBUFSIZE 0x04
+#define B43_PIO_RXCTL 0x08
+#define B43_PIO_RXDATA 0x0A
+
+#define B43_PIO_TXCTL_WRITELO (1 << 0)
+#define B43_PIO_TXCTL_WRITEHI (1 << 1)
+#define B43_PIO_TXCTL_COMPLETE (1 << 2)
+#define B43_PIO_TXCTL_INIT (1 << 3)
+#define B43_PIO_TXCTL_SUSPEND (1 << 7)
+
+#define B43_PIO_RXCTL_DATAAVAILABLE (1 << 0)
+#define B43_PIO_RXCTL_READY (1 << 1)
+
+/* PIO constants */
+#define B43_PIO_MAXTXDEVQPACKETS 31
+#define B43_PIO_TXQADJUST 80
+
+/* PIO tuning knobs */
+#define B43_PIO_MAXTXPACKETS 256
+
+#ifdef CONFIG_B43_PIO
+
+struct b43_pioqueue;
+struct b43_xmitstatus;
+
+struct b43_pio_txpacket {
+ struct b43_pioqueue *queue;
+ struct sk_buff *skb;
+ struct ieee80211_tx_status txstat;
+ struct list_head list;
+};
+
+#define pio_txpacket_getindex(packet) ((int)((packet) - (packet)->queue->tx_packets_cache))
+
+struct b43_pioqueue {
+ struct b43_wldev *dev;
+ u16 mmio_base;
+
+ bool tx_suspended;
+ bool tx_frozen;
+ bool need_workarounds; /* Workarounds needed for core.rev < 3 */
+
+ /* Adjusted size of the device internal TX buffer. */
+ u16 tx_devq_size;
+ /* Used octets of the device internal TX buffer. */
+ u16 tx_devq_used;
+ /* Used packet slots in the device internal TX buffer. */
+ u8 tx_devq_packets;
+ /* Packets from the txfree list can
+ * be taken on incoming TX requests.
+ */
+ struct list_head txfree;
+ unsigned int nr_txfree;
+ /* Packets on the txqueue are queued,
+ * but not completely written to the chip, yet.
+ */
+ struct list_head txqueue;
+ /* Packets on the txrunning queue are completely
+ * posted to the device. We are waiting for the txstatus.
+ */
+ struct list_head txrunning;
+ /* Total number or packets sent.
+ * (This counter can obviously wrap).
+ */
+ unsigned int nr_tx_packets;
+ struct tasklet_struct txtask;
+ struct b43_pio_txpacket tx_packets_cache[B43_PIO_MAXTXPACKETS];
+};
+
+static inline u16 b43_pio_read(struct b43_pioqueue *queue, u16 offset)
+{
+ return b43_read16(queue->dev, queue->mmio_base + offset);
+}
+
+static inline
+ void b43_pio_write(struct b43_pioqueue *queue, u16 offset, u16 value)
+{
+ b43_write16(queue->dev, queue->mmio_base + offset, value);
+ mmiowb();
+}
+
+int b43_pio_init(struct b43_wldev *dev);
+void b43_pio_free(struct b43_wldev *dev);
+
+int b43_pio_tx(struct b43_wldev *dev,
+ struct sk_buff *skb, struct ieee80211_tx_control *ctl);
+void b43_pio_handle_txstatus(struct b43_wldev *dev,
+ const struct b43_txstatus *status);
+void b43_pio_get_tx_stats(struct b43_wldev *dev,
+ struct ieee80211_tx_queue_stats *stats);
+void b43_pio_rx(struct b43_pioqueue *queue);
+
+/* Suspend TX queue in hardware. */
+void b43_pio_tx_suspend(struct b43_pioqueue *queue);
+void b43_pio_tx_resume(struct b43_pioqueue *queue);
+/* Suspend (freeze) the TX tasklet (software level). */
+void b43_pio_freeze_txqueues(struct b43_wldev *dev);
+void b43_pio_thaw_txqueues(struct b43_wldev *dev);
+
+#else /* CONFIG_B43_PIO */
+
+static inline int b43_pio_init(struct b43_wldev *dev)
+{
+ return 0;
+}
+static inline void b43_pio_free(struct b43_wldev *dev)
+{
+}
+static inline
+ int b43_pio_tx(struct b43_wldev *dev,
+ struct sk_buff *skb, struct ieee80211_tx_control *ctl)
+{
+ return 0;
+}
+static inline
+ void b43_pio_handle_txstatus(struct b43_wldev *dev,
+ const struct b43_txstatus *status)
+{
+}
+static inline
+ void b43_pio_get_tx_stats(struct b43_wldev *dev,
+ struct ieee80211_tx_queue_stats *stats)
+{
+}
+static inline void b43_pio_rx(struct b43_pioqueue *queue)
+{
+}
+static inline void b43_pio_tx_suspend(struct b43_pioqueue *queue)
+{
+}
+static inline void b43_pio_tx_resume(struct b43_pioqueue *queue)
+{
+}
+static inline void b43_pio_freeze_txqueues(struct b43_wldev *dev)
+{
+}
+static inline void b43_pio_thaw_txqueues(struct b43_wldev *dev)
+{
+}
+
+#endif /* CONFIG_B43_PIO */
+#endif /* B43_PIO_H_ */
--- /dev/null
+/*
+
+ Broadcom B43 wireless driver
+
+ SYSFS support routines
+
+ Copyright (c) 2006 Michael Buesch <mb@bu3sch.de>
+
+ This program is free software; you can redistribute it and/or modify
+ it under the terms of the GNU General Public License as published by
+ the Free Software Foundation; either version 2 of the License, or
+ (at your option) any later version.
+
+ This program is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ GNU General Public License for more details.
+
+ You should have received a copy of the GNU General Public License
+ along with this program; see the file COPYING. If not, write to
+ the Free Software Foundation, Inc., 51 Franklin Steet, Fifth Floor,
+ Boston, MA 02110-1301, USA.
+
+*/
+
+#include "b43.h"
+#include "sysfs.h"
+#include "main.h"
+#include "phy.h"
+
+#include <linux/capability.h>
+
+#define GENERIC_FILESIZE 64
+
+static int get_integer(const char *buf, size_t count)
+{
+ char tmp[10 + 1] = { 0 };
+ int ret = -EINVAL;
+
+ if (count == 0)
+ goto out;
+ count = min(count, (size_t) 10);
+ memcpy(tmp, buf, count);
+ ret = simple_strtol(tmp, NULL, 10);
+ out:
+ return ret;
+}
+
+static int get_boolean(const char *buf, size_t count)
+{
+ if (count != 0) {
+ if (buf[0] == '1')
+ return 1;
+ if (buf[0] == '0')
+ return 0;
+ if (count >= 4 && memcmp(buf, "true", 4) == 0)
+ return 1;
+ if (count >= 5 && memcmp(buf, "false", 5) == 0)
+ return 0;
+ if (count >= 3 && memcmp(buf, "yes", 3) == 0)
+ return 1;
+ if (count >= 2 && memcmp(buf, "no", 2) == 0)
+ return 0;
+ if (count >= 2 && memcmp(buf, "on", 2) == 0)
+ return 1;
+ if (count >= 3 && memcmp(buf, "off", 3) == 0)
+ return 0;
+ }
+ return -EINVAL;
+}
+
+static ssize_t b43_attr_interfmode_show(struct device *dev,
+ struct device_attribute *attr,
+ char *buf)
+{
+ struct b43_wldev *wldev = dev_to_b43_wldev(dev);
+ ssize_t count = 0;
+
+ if (!capable(CAP_NET_ADMIN))
+ return -EPERM;
+
+ mutex_lock(&wldev->wl->mutex);
+
+ switch (wldev->phy.interfmode) {
+ case B43_INTERFMODE_NONE:
+ count =
+ snprintf(buf, PAGE_SIZE,
+ "0 (No Interference Mitigation)\n");
+ break;
+ case B43_INTERFMODE_NONWLAN:
+ count =
+ snprintf(buf, PAGE_SIZE,
+ "1 (Non-WLAN Interference Mitigation)\n");
+ break;
+ case B43_INTERFMODE_MANUALWLAN:
+ count =
+ snprintf(buf, PAGE_SIZE,
+ "2 (WLAN Interference Mitigation)\n");
+ break;
+ default:
+ B43_WARN_ON(1);
+ }
+
+ mutex_unlock(&wldev->wl->mutex);
+
+ return count;
+}
+
+static ssize_t b43_attr_interfmode_store(struct device *dev,
+ struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct b43_wldev *wldev = dev_to_b43_wldev(dev);
+ unsigned long flags;
+ int err;
+ int mode;
+
+ if (!capable(CAP_NET_ADMIN))
+ return -EPERM;
+
+ mode = get_integer(buf, count);
+ switch (mode) {
+ case 0:
+ mode = B43_INTERFMODE_NONE;
+ break;
+ case 1:
+ mode = B43_INTERFMODE_NONWLAN;
+ break;
+ case 2:
+ mode = B43_INTERFMODE_MANUALWLAN;
+ break;
+ case 3:
+ mode = B43_INTERFMODE_AUTOWLAN;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ mutex_lock(&wldev->wl->mutex);
+ spin_lock_irqsave(&wldev->wl->irq_lock, flags);
+
+ err = b43_radio_set_interference_mitigation(wldev, mode);
+ if (err) {
+ b43err(wldev->wl, "Interference Mitigation not "
+ "supported by device\n");
+ }
+ mmiowb();
+ spin_unlock_irqrestore(&wldev->wl->irq_lock, flags);
+ mutex_unlock(&wldev->wl->mutex);
+
+ return err ? err : count;
+}
+
+static DEVICE_ATTR(interference, 0644,
+ b43_attr_interfmode_show, b43_attr_interfmode_store);
+
+static ssize_t b43_attr_preamble_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct b43_wldev *wldev = dev_to_b43_wldev(dev);
+ ssize_t count;
+
+ if (!capable(CAP_NET_ADMIN))
+ return -EPERM;
+
+ mutex_lock(&wldev->wl->mutex);
+
+ if (wldev->short_preamble)
+ count =
+ snprintf(buf, PAGE_SIZE, "1 (Short Preamble enabled)\n");
+ else
+ count =
+ snprintf(buf, PAGE_SIZE, "0 (Short Preamble disabled)\n");
+
+ mutex_unlock(&wldev->wl->mutex);
+
+ return count;
+}
+
+static ssize_t b43_attr_preamble_store(struct device *dev,
+ struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct b43_wldev *wldev = dev_to_b43_wldev(dev);
+ unsigned long flags;
+ int value;
+
+ if (!capable(CAP_NET_ADMIN))
+ return -EPERM;
+
+ value = get_boolean(buf, count);
+ if (value < 0)
+ return value;
+ mutex_lock(&wldev->wl->mutex);
+ spin_lock_irqsave(&wldev->wl->irq_lock, flags);
+
+ wldev->short_preamble = !!value;
+
+ spin_unlock_irqrestore(&wldev->wl->irq_lock, flags);
+ mutex_unlock(&wldev->wl->mutex);
+
+ return count;
+}
+
+static DEVICE_ATTR(shortpreamble, 0644,
+ b43_attr_preamble_show, b43_attr_preamble_store);
+
+int b43_sysfs_register(struct b43_wldev *wldev)
+{
+ struct device *dev = wldev->dev->dev;
+ int err;
+
+ B43_WARN_ON(b43_status(wldev) != B43_STAT_INITIALIZED);
+
+ err = device_create_file(dev, &dev_attr_interference);
+ if (err)
+ goto out;
+ err = device_create_file(dev, &dev_attr_shortpreamble);
+ if (err)
+ goto err_remove_interfmode;
+
+ out:
+ return err;
+ err_remove_interfmode:
+ device_remove_file(dev, &dev_attr_interference);
+ goto out;
+}
+
+void b43_sysfs_unregister(struct b43_wldev *wldev)
+{
+ struct device *dev = wldev->dev->dev;
+
+ device_remove_file(dev, &dev_attr_shortpreamble);
+ device_remove_file(dev, &dev_attr_interference);
+}
--- /dev/null
+#ifndef B43_SYSFS_H_
+#define B43_SYSFS_H_
+
+struct b43_wldev;
+
+int b43_sysfs_register(struct b43_wldev *dev);
+void b43_sysfs_unregister(struct b43_wldev *dev);
+
+#endif /* B43_SYSFS_H_ */
--- /dev/null
+/*
+
+ Broadcom B43 wireless driver
+
+ Copyright (c) 2005 Martin Langer <martin-langer@gmx.de>,
+ Copyright (c) 2005 Stefano Brivio <st3@riseup.net>
+ Copyright (c) 2006, 2006 Michael Buesch <mb@bu3sch.de>
+ Copyright (c) 2005 Danny van Dyk <kugelfang@gentoo.org>
+ Copyright (c) 2005 Andreas Jaggi <andreas.jaggi@waterwave.ch>
+
+ This program is free software; you can redistribute it and/or modify
+ it under the terms of the GNU General Public License as published by
+ the Free Software Foundation; either version 2 of the License, or
+ (at your option) any later version.
+
+ This program is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ GNU General Public License for more details.
+
+ You should have received a copy of the GNU General Public License
+ along with this program; see the file COPYING. If not, write to
+ the Free Software Foundation, Inc., 51 Franklin Steet, Fifth Floor,
+ Boston, MA 02110-1301, USA.
+
+*/
+
+#include "b43.h"
+#include "tables.h"
+#include "phy.h"
+
+const u32 b43_tab_rotor[] = {
+ 0xFEB93FFD, 0xFEC63FFD, /* 0 */
+ 0xFED23FFD, 0xFEDF3FFD,
+ 0xFEEC3FFE, 0xFEF83FFE,
+ 0xFF053FFE, 0xFF113FFE,
+ 0xFF1E3FFE, 0xFF2A3FFF, /* 8 */
+ 0xFF373FFF, 0xFF443FFF,
+ 0xFF503FFF, 0xFF5D3FFF,
+ 0xFF693FFF, 0xFF763FFF,
+ 0xFF824000, 0xFF8F4000, /* 16 */
+ 0xFF9B4000, 0xFFA84000,
+ 0xFFB54000, 0xFFC14000,
+ 0xFFCE4000, 0xFFDA4000,
+ 0xFFE74000, 0xFFF34000, /* 24 */
+ 0x00004000, 0x000D4000,
+ 0x00194000, 0x00264000,
+ 0x00324000, 0x003F4000,
+ 0x004B4000, 0x00584000, /* 32 */
+ 0x00654000, 0x00714000,
+ 0x007E4000, 0x008A3FFF,
+ 0x00973FFF, 0x00A33FFF,
+ 0x00B03FFF, 0x00BC3FFF, /* 40 */
+ 0x00C93FFF, 0x00D63FFF,
+ 0x00E23FFE, 0x00EF3FFE,
+ 0x00FB3FFE, 0x01083FFE,
+ 0x01143FFE, 0x01213FFD, /* 48 */
+ 0x012E3FFD, 0x013A3FFD,
+ 0x01473FFD,
+};
+
+const u32 b43_tab_retard[] = {
+ 0xDB93CB87, 0xD666CF64, /* 0 */
+ 0xD1FDD358, 0xCDA6D826,
+ 0xCA38DD9F, 0xC729E2B4,
+ 0xC469E88E, 0xC26AEE2B,
+ 0xC0DEF46C, 0xC073FA62, /* 8 */
+ 0xC01D00D5, 0xC0760743,
+ 0xC1560D1E, 0xC2E51369,
+ 0xC4ED18FF, 0xC7AC1ED7,
+ 0xCB2823B2, 0xCEFA28D9, /* 16 */
+ 0xD2F62D3F, 0xD7BB3197,
+ 0xDCE53568, 0xE1FE3875,
+ 0xE7D13B35, 0xED663D35,
+ 0xF39B3EC4, 0xF98E3FA7, /* 24 */
+ 0x00004000, 0x06723FA7,
+ 0x0C653EC4, 0x129A3D35,
+ 0x182F3B35, 0x1E023875,
+ 0x231B3568, 0x28453197, /* 32 */
+ 0x2D0A2D3F, 0x310628D9,
+ 0x34D823B2, 0x38541ED7,
+ 0x3B1318FF, 0x3D1B1369,
+ 0x3EAA0D1E, 0x3F8A0743, /* 40 */
+ 0x3FE300D5, 0x3F8DFA62,
+ 0x3F22F46C, 0x3D96EE2B,
+ 0x3B97E88E, 0x38D7E2B4,
+ 0x35C8DD9F, 0x325AD826, /* 48 */
+ 0x2E03D358, 0x299ACF64,
+ 0x246DCB87,
+};
+
+const u16 b43_tab_finefreqa[] = {
+ 0x0082, 0x0082, 0x0102, 0x0182, /* 0 */
+ 0x0202, 0x0282, 0x0302, 0x0382,
+ 0x0402, 0x0482, 0x0502, 0x0582,
+ 0x05E2, 0x0662, 0x06E2, 0x0762,
+ 0x07E2, 0x0842, 0x08C2, 0x0942, /* 16 */
+ 0x09C2, 0x0A22, 0x0AA2, 0x0B02,
+ 0x0B82, 0x0BE2, 0x0C62, 0x0CC2,
+ 0x0D42, 0x0DA2, 0x0E02, 0x0E62,
+ 0x0EE2, 0x0F42, 0x0FA2, 0x1002, /* 32 */
+ 0x1062, 0x10C2, 0x1122, 0x1182,
+ 0x11E2, 0x1242, 0x12A2, 0x12E2,
+ 0x1342, 0x13A2, 0x1402, 0x1442,
+ 0x14A2, 0x14E2, 0x1542, 0x1582, /* 48 */
+ 0x15E2, 0x1622, 0x1662, 0x16C1,
+ 0x1701, 0x1741, 0x1781, 0x17E1,
+ 0x1821, 0x1861, 0x18A1, 0x18E1,
+ 0x1921, 0x1961, 0x19A1, 0x19E1, /* 64 */
+ 0x1A21, 0x1A61, 0x1AA1, 0x1AC1,
+ 0x1B01, 0x1B41, 0x1B81, 0x1BA1,
+ 0x1BE1, 0x1C21, 0x1C41, 0x1C81,
+ 0x1CA1, 0x1CE1, 0x1D01, 0x1D41, /* 80 */
+ 0x1D61, 0x1DA1, 0x1DC1, 0x1E01,
+ 0x1E21, 0x1E61, 0x1E81, 0x1EA1,
+ 0x1EE1, 0x1F01, 0x1F21, 0x1F41,
+ 0x1F81, 0x1FA1, 0x1FC1, 0x1FE1, /* 96 */
+ 0x2001, 0x2041, 0x2061, 0x2081,
+ 0x20A1, 0x20C1, 0x20E1, 0x2101,
+ 0x2121, 0x2141, 0x2161, 0x2181,
+ 0x21A1, 0x21C1, 0x21E1, 0x2201, /* 112 */
+ 0x2221, 0x2241, 0x2261, 0x2281,
+ 0x22A1, 0x22C1, 0x22C1, 0x22E1,
+ 0x2301, 0x2321, 0x2341, 0x2361,
+ 0x2361, 0x2381, 0x23A1, 0x23C1, /* 128 */
+ 0x23E1, 0x23E1, 0x2401, 0x2421,
+ 0x2441, 0x2441, 0x2461, 0x2481,
+ 0x2481, 0x24A1, 0x24C1, 0x24C1,
+ 0x24E1, 0x2501, 0x2501, 0x2521, /* 144 */
+ 0x2541, 0x2541, 0x2561, 0x2561,
+ 0x2581, 0x25A1, 0x25A1, 0x25C1,
+ 0x25C1, 0x25E1, 0x2601, 0x2601,
+ 0x2621, 0x2621, 0x2641, 0x2641, /* 160 */
+ 0x2661, 0x2661, 0x2681, 0x2681,
+ 0x26A1, 0x26A1, 0x26C1, 0x26C1,
+ 0x26E1, 0x26E1, 0x2701, 0x2701,
+ 0x2721, 0x2721, 0x2740, 0x2740, /* 176 */
+ 0x2760, 0x2760, 0x2780, 0x2780,
+ 0x2780, 0x27A0, 0x27A0, 0x27C0,
+ 0x27C0, 0x27E0, 0x27E0, 0x27E0,
+ 0x2800, 0x2800, 0x2820, 0x2820, /* 192 */
+ 0x2820, 0x2840, 0x2840, 0x2840,
+ 0x2860, 0x2860, 0x2880, 0x2880,
+ 0x2880, 0x28A0, 0x28A0, 0x28A0,
+ 0x28C0, 0x28C0, 0x28C0, 0x28E0, /* 208 */
+ 0x28E0, 0x28E0, 0x2900, 0x2900,
+ 0x2900, 0x2920, 0x2920, 0x2920,
+ 0x2940, 0x2940, 0x2940, 0x2960,
+ 0x2960, 0x2960, 0x2960, 0x2980, /* 224 */
+ 0x2980, 0x2980, 0x29A0, 0x29A0,
+ 0x29A0, 0x29A0, 0x29C0, 0x29C0,
+ 0x29C0, 0x29E0, 0x29E0, 0x29E0,
+ 0x29E0, 0x2A00, 0x2A00, 0x2A00, /* 240 */
+ 0x2A00, 0x2A20, 0x2A20, 0x2A20,
+ 0x2A20, 0x2A40, 0x2A40, 0x2A40,
+ 0x2A40, 0x2A60, 0x2A60, 0x2A60,
+};
+
+const u16 b43_tab_finefreqg[] = {
+ 0x0089, 0x02E9, 0x0409, 0x04E9, /* 0 */
+ 0x05A9, 0x0669, 0x0709, 0x0789,
+ 0x0829, 0x08A9, 0x0929, 0x0989,
+ 0x0A09, 0x0A69, 0x0AC9, 0x0B29,
+ 0x0BA9, 0x0BE9, 0x0C49, 0x0CA9, /* 16 */
+ 0x0D09, 0x0D69, 0x0DA9, 0x0E09,
+ 0x0E69, 0x0EA9, 0x0F09, 0x0F49,
+ 0x0FA9, 0x0FE9, 0x1029, 0x1089,
+ 0x10C9, 0x1109, 0x1169, 0x11A9, /* 32 */
+ 0x11E9, 0x1229, 0x1289, 0x12C9,
+ 0x1309, 0x1349, 0x1389, 0x13C9,
+ 0x1409, 0x1449, 0x14A9, 0x14E9,
+ 0x1529, 0x1569, 0x15A9, 0x15E9, /* 48 */
+ 0x1629, 0x1669, 0x16A9, 0x16E8,
+ 0x1728, 0x1768, 0x17A8, 0x17E8,
+ 0x1828, 0x1868, 0x18A8, 0x18E8,
+ 0x1928, 0x1968, 0x19A8, 0x19E8, /* 64 */
+ 0x1A28, 0x1A68, 0x1AA8, 0x1AE8,
+ 0x1B28, 0x1B68, 0x1BA8, 0x1BE8,
+ 0x1C28, 0x1C68, 0x1CA8, 0x1CE8,
+ 0x1D28, 0x1D68, 0x1DC8, 0x1E08, /* 80 */
+ 0x1E48, 0x1E88, 0x1EC8, 0x1F08,
+ 0x1F48, 0x1F88, 0x1FE8, 0x2028,
+ 0x2068, 0x20A8, 0x2108, 0x2148,
+ 0x2188, 0x21C8, 0x2228, 0x2268, /* 96 */
+ 0x22C8, 0x2308, 0x2348, 0x23A8,
+ 0x23E8, 0x2448, 0x24A8, 0x24E8,
+ 0x2548, 0x25A8, 0x2608, 0x2668,
+ 0x26C8, 0x2728, 0x2787, 0x27E7, /* 112 */
+ 0x2847, 0x28C7, 0x2947, 0x29A7,
+ 0x2A27, 0x2AC7, 0x2B47, 0x2BE7,
+ 0x2CA7, 0x2D67, 0x2E47, 0x2F67,
+ 0x3247, 0x3526, 0x3646, 0x3726, /* 128 */
+ 0x3806, 0x38A6, 0x3946, 0x39E6,
+ 0x3A66, 0x3AE6, 0x3B66, 0x3BC6,
+ 0x3C45, 0x3CA5, 0x3D05, 0x3D85,
+ 0x3DE5, 0x3E45, 0x3EA5, 0x3EE5, /* 144 */
+ 0x3F45, 0x3FA5, 0x4005, 0x4045,
+ 0x40A5, 0x40E5, 0x4145, 0x4185,
+ 0x41E5, 0x4225, 0x4265, 0x42C5,
+ 0x4305, 0x4345, 0x43A5, 0x43E5, /* 160 */
+ 0x4424, 0x4464, 0x44C4, 0x4504,
+ 0x4544, 0x4584, 0x45C4, 0x4604,
+ 0x4644, 0x46A4, 0x46E4, 0x4724,
+ 0x4764, 0x47A4, 0x47E4, 0x4824, /* 176 */
+ 0x4864, 0x48A4, 0x48E4, 0x4924,
+ 0x4964, 0x49A4, 0x49E4, 0x4A24,
+ 0x4A64, 0x4AA4, 0x4AE4, 0x4B23,
+ 0x4B63, 0x4BA3, 0x4BE3, 0x4C23, /* 192 */
+ 0x4C63, 0x4CA3, 0x4CE3, 0x4D23,
+ 0x4D63, 0x4DA3, 0x4DE3, 0x4E23,
+ 0x4E63, 0x4EA3, 0x4EE3, 0x4F23,
+ 0x4F63, 0x4FC3, 0x5003, 0x5043, /* 208 */
+ 0x5083, 0x50C3, 0x5103, 0x5143,
+ 0x5183, 0x51E2, 0x5222, 0x5262,
+ 0x52A2, 0x52E2, 0x5342, 0x5382,
+ 0x53C2, 0x5402, 0x5462, 0x54A2, /* 224 */
+ 0x5502, 0x5542, 0x55A2, 0x55E2,
+ 0x5642, 0x5682, 0x56E2, 0x5722,
+ 0x5782, 0x57E1, 0x5841, 0x58A1,
+ 0x5901, 0x5961, 0x59C1, 0x5A21, /* 240 */
+ 0x5AA1, 0x5B01, 0x5B81, 0x5BE1,
+ 0x5C61, 0x5D01, 0x5D80, 0x5E20,
+ 0x5EE0, 0x5FA0, 0x6080, 0x61C0,
+};
+
+const u16 b43_tab_noisea2[] = {
+ 0x0001, 0x0001, 0x0001, 0xFFFE,
+ 0xFFFE, 0x3FFF, 0x1000, 0x0393,
+};
+
+const u16 b43_tab_noisea3[] = {
+ 0x4C4C, 0x4C4C, 0x4C4C, 0x2D36,
+ 0x4C4C, 0x4C4C, 0x4C4C, 0x2D36,
+};
+
+const u16 b43_tab_noiseg1[] = {
+ 0x013C, 0x01F5, 0x031A, 0x0631,
+ 0x0001, 0x0001, 0x0001, 0x0001,
+};
+
+const u16 b43_tab_noiseg2[] = {
+ 0x5484, 0x3C40, 0x0000, 0x0000,
+ 0x0000, 0x0000, 0x0000, 0x0000,
+};
+
+const u16 b43_tab_noisescaleg1[] = {
+ 0x6C77, 0x5162, 0x3B40, 0x3335, /* 0 */
+ 0x2F2D, 0x2A2A, 0x2527, 0x1F21,
+ 0x1A1D, 0x1719, 0x1616, 0x1414,
+ 0x1414, 0x1400, 0x1414, 0x1614,
+ 0x1716, 0x1A19, 0x1F1D, 0x2521, /* 16 */
+ 0x2A27, 0x2F2A, 0x332D, 0x3B35,
+ 0x5140, 0x6C62, 0x0077,
+};
+
+const u16 b43_tab_noisescaleg2[] = {
+ 0xD8DD, 0xCBD4, 0xBCC0, 0XB6B7, /* 0 */
+ 0xB2B0, 0xADAD, 0xA7A9, 0x9FA1,
+ 0x969B, 0x9195, 0x8F8F, 0x8A8A,
+ 0x8A8A, 0x8A00, 0x8A8A, 0x8F8A,
+ 0x918F, 0x9695, 0x9F9B, 0xA7A1, /* 16 */
+ 0xADA9, 0xB2AD, 0xB6B0, 0xBCB7,
+ 0xCBC0, 0xD8D4, 0x00DD,
+};
+
+const u16 b43_tab_noisescaleg3[] = {
+ 0xA4A4, 0xA4A4, 0xA4A4, 0xA4A4, /* 0 */
+ 0xA4A4, 0xA4A4, 0xA4A4, 0xA4A4,
+ 0xA4A4, 0xA4A4, 0xA4A4, 0xA4A4,
+ 0xA4A4, 0xA400, 0xA4A4, 0xA4A4,
+ 0xA4A4, 0xA4A4, 0xA4A4, 0xA4A4, /* 16 */
+ 0xA4A4, 0xA4A4, 0xA4A4, 0xA4A4,
+ 0xA4A4, 0xA4A4, 0x00A4,
+};
+
+const u16 b43_tab_sigmasqr1[] = {
+ 0x007A, 0x0075, 0x0071, 0x006C, /* 0 */
+ 0x0067, 0x0063, 0x005E, 0x0059,
+ 0x0054, 0x0050, 0x004B, 0x0046,
+ 0x0042, 0x003D, 0x003D, 0x003D,
+ 0x003D, 0x003D, 0x003D, 0x003D, /* 16 */
+ 0x003D, 0x003D, 0x003D, 0x003D,
+ 0x003D, 0x003D, 0x0000, 0x003D,
+ 0x003D, 0x003D, 0x003D, 0x003D,
+ 0x003D, 0x003D, 0x003D, 0x003D, /* 32 */
+ 0x003D, 0x003D, 0x003D, 0x003D,
+ 0x0042, 0x0046, 0x004B, 0x0050,
+ 0x0054, 0x0059, 0x005E, 0x0063,
+ 0x0067, 0x006C, 0x0071, 0x0075, /* 48 */
+ 0x007A,
+};
+
+const u16 b43_tab_sigmasqr2[] = {
+ 0x00DE, 0x00DC, 0x00DA, 0x00D8, /* 0 */
+ 0x00D6, 0x00D4, 0x00D2, 0x00CF,
+ 0x00CD, 0x00CA, 0x00C7, 0x00C4,
+ 0x00C1, 0x00BE, 0x00BE, 0x00BE,
+ 0x00BE, 0x00BE, 0x00BE, 0x00BE, /* 16 */
+ 0x00BE, 0x00BE, 0x00BE, 0x00BE,
+ 0x00BE, 0x00BE, 0x0000, 0x00BE,
+ 0x00BE, 0x00BE, 0x00BE, 0x00BE,
+ 0x00BE, 0x00BE, 0x00BE, 0x00BE, /* 32 */
+ 0x00BE, 0x00BE, 0x00BE, 0x00BE,
+ 0x00C1, 0x00C4, 0x00C7, 0x00CA,
+ 0x00CD, 0x00CF, 0x00D2, 0x00D4,
+ 0x00D6, 0x00D8, 0x00DA, 0x00DC, /* 48 */
+ 0x00DE,
+};
+
+static inline void assert_sizes(void)
+{
+ BUILD_BUG_ON(B43_TAB_ROTOR_SIZE != ARRAY_SIZE(b43_tab_rotor));
+ BUILD_BUG_ON(B43_TAB_RETARD_SIZE != ARRAY_SIZE(b43_tab_retard));
+ BUILD_BUG_ON(B43_TAB_FINEFREQA_SIZE != ARRAY_SIZE(b43_tab_finefreqa));
+ BUILD_BUG_ON(B43_TAB_FINEFREQG_SIZE != ARRAY_SIZE(b43_tab_finefreqg));
+ BUILD_BUG_ON(B43_TAB_NOISEA2_SIZE != ARRAY_SIZE(b43_tab_noisea2));
+ BUILD_BUG_ON(B43_TAB_NOISEA3_SIZE != ARRAY_SIZE(b43_tab_noisea3));
+ BUILD_BUG_ON(B43_TAB_NOISEG1_SIZE != ARRAY_SIZE(b43_tab_noiseg1));
+ BUILD_BUG_ON(B43_TAB_NOISEG2_SIZE != ARRAY_SIZE(b43_tab_noiseg2));
+ BUILD_BUG_ON(B43_TAB_NOISESCALEG_SIZE !=
+ ARRAY_SIZE(b43_tab_noisescaleg1));
+ BUILD_BUG_ON(B43_TAB_NOISESCALEG_SIZE !=
+ ARRAY_SIZE(b43_tab_noisescaleg2));
+ BUILD_BUG_ON(B43_TAB_NOISESCALEG_SIZE !=
+ ARRAY_SIZE(b43_tab_noisescaleg3));
+ BUILD_BUG_ON(B43_TAB_SIGMASQR_SIZE != ARRAY_SIZE(b43_tab_sigmasqr1));
+ BUILD_BUG_ON(B43_TAB_SIGMASQR_SIZE != ARRAY_SIZE(b43_tab_sigmasqr2));
+}
+
+u16 b43_ofdmtab_read16(struct b43_wldev *dev, u16 table, u16 offset)
+{
+ assert_sizes();
+
+ b43_phy_write(dev, B43_PHY_OTABLECTL, table + offset);
+ return b43_phy_read(dev, B43_PHY_OTABLEI);
+}
+
+void b43_ofdmtab_write16(struct b43_wldev *dev, u16 table,
+ u16 offset, u16 value)
+{
+ b43_phy_write(dev, B43_PHY_OTABLECTL, table + offset);
+ b43_phy_write(dev, B43_PHY_OTABLEI, value);
+}
+
+u32 b43_ofdmtab_read32(struct b43_wldev *dev, u16 table, u16 offset)
+{
+ u32 ret;
+
+ b43_phy_write(dev, B43_PHY_OTABLECTL, table + offset);
+ ret = b43_phy_read(dev, B43_PHY_OTABLEQ);
+ ret <<= 16;
+ ret |= b43_phy_read(dev, B43_PHY_OTABLEI);
+
+ return ret;
+}
+
+void b43_ofdmtab_write32(struct b43_wldev *dev, u16 table,
+ u16 offset, u32 value)
+{
+ b43_phy_write(dev, B43_PHY_OTABLECTL, table + offset);
+ b43_phy_write(dev, B43_PHY_OTABLEI, value);
+ b43_phy_write(dev, B43_PHY_OTABLEQ, (value >> 16));
+}
+
+u16 b43_gtab_read(struct b43_wldev *dev, u16 table, u16 offset)
+{
+ b43_phy_write(dev, B43_PHY_GTABCTL, table + offset);
+ return b43_phy_read(dev, B43_PHY_GTABDATA);
+}
+
+void b43_gtab_write(struct b43_wldev *dev, u16 table, u16 offset, u16 value)
+{
+ b43_phy_write(dev, B43_PHY_GTABCTL, table + offset);
+ b43_phy_write(dev, B43_PHY_GTABDATA, value);
+}
--- /dev/null
+#ifndef B43_TABLES_H_
+#define B43_TABLES_H_
+
+#define B43_TAB_ROTOR_SIZE 53
+extern const u32 b43_tab_rotor[];
+#define B43_TAB_RETARD_SIZE 53
+extern const u32 b43_tab_retard[];
+#define B43_TAB_FINEFREQA_SIZE 256
+extern const u16 b43_tab_finefreqa[];
+#define B43_TAB_FINEFREQG_SIZE 256
+extern const u16 b43_tab_finefreqg[];
+#define B43_TAB_NOISEA2_SIZE 8
+extern const u16 b43_tab_noisea2[];
+#define B43_TAB_NOISEA3_SIZE 8
+extern const u16 b43_tab_noisea3[];
+#define B43_TAB_NOISEG1_SIZE 8
+extern const u16 b43_tab_noiseg1[];
+#define B43_TAB_NOISEG2_SIZE 8
+extern const u16 b43_tab_noiseg2[];
+#define B43_TAB_NOISESCALEG_SIZE 27
+extern const u16 b43_tab_noisescaleg1[];
+extern const u16 b43_tab_noisescaleg2[];
+extern const u16 b43_tab_noisescaleg3[];
+#define B43_TAB_SIGMASQR_SIZE 53
+extern const u16 b43_tab_sigmasqr1[];
+extern const u16 b43_tab_sigmasqr2[];
+
+#endif /* B43_TABLES_H_ */
--- /dev/null
+/*
+
+ Broadcom B43 wireless driver
+
+ Transmission (TX/RX) related functions.
+
+ Copyright (C) 2005 Martin Langer <martin-langer@gmx.de>
+ Copyright (C) 2005 Stefano Brivio <st3@riseup.net>
+ Copyright (C) 2005, 2006 Michael Buesch <mb@bu3sch.de>
+ Copyright (C) 2005 Danny van Dyk <kugelfang@gentoo.org>
+ Copyright (C) 2005 Andreas Jaggi <andreas.jaggi@waterwave.ch>
+
+ This program is free software; you can redistribute it and/or modify
+ it under the terms of the GNU General Public License as published by
+ the Free Software Foundation; either version 2 of the License, or
+ (at your option) any later version.
+
+ This program is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ GNU General Public License for more details.
+
+ You should have received a copy of the GNU General Public License
+ along with this program; see the file COPYING. If not, write to
+ the Free Software Foundation, Inc., 51 Franklin Steet, Fifth Floor,
+ Boston, MA 02110-1301, USA.
+
+*/
+
+#include "xmit.h"
+#include "phy.h"
+#include "dma.h"
+#include "pio.h"
+
+/* Extract the bitrate out of a CCK PLCP header. */
+static u8 b43_plcp_get_bitrate_cck(struct b43_plcp_hdr6 *plcp)
+{
+ switch (plcp->raw[0]) {
+ case 0x0A:
+ return B43_CCK_RATE_1MB;
+ case 0x14:
+ return B43_CCK_RATE_2MB;
+ case 0x37:
+ return B43_CCK_RATE_5MB;
+ case 0x6E:
+ return B43_CCK_RATE_11MB;
+ }
+ B43_WARN_ON(1);
+ return 0;
+}
+
+/* Extract the bitrate out of an OFDM PLCP header. */
+static u8 b43_plcp_get_bitrate_ofdm(struct b43_plcp_hdr6 *plcp)
+{
+ switch (plcp->raw[0] & 0xF) {
+ case 0xB:
+ return B43_OFDM_RATE_6MB;
+ case 0xF:
+ return B43_OFDM_RATE_9MB;
+ case 0xA:
+ return B43_OFDM_RATE_12MB;
+ case 0xE:
+ return B43_OFDM_RATE_18MB;
+ case 0x9:
+ return B43_OFDM_RATE_24MB;
+ case 0xD:
+ return B43_OFDM_RATE_36MB;
+ case 0x8:
+ return B43_OFDM_RATE_48MB;
+ case 0xC:
+ return B43_OFDM_RATE_54MB;
+ }
+ B43_WARN_ON(1);
+ return 0;
+}
+
+u8 b43_plcp_get_ratecode_cck(const u8 bitrate)
+{
+ switch (bitrate) {
+ case B43_CCK_RATE_1MB:
+ return 0x0A;
+ case B43_CCK_RATE_2MB:
+ return 0x14;
+ case B43_CCK_RATE_5MB:
+ return 0x37;
+ case B43_CCK_RATE_11MB:
+ return 0x6E;
+ }
+ B43_WARN_ON(1);
+ return 0;
+}
+
+u8 b43_plcp_get_ratecode_ofdm(const u8 bitrate)
+{
+ switch (bitrate) {
+ case B43_OFDM_RATE_6MB:
+ return 0xB;
+ case B43_OFDM_RATE_9MB:
+ return 0xF;
+ case B43_OFDM_RATE_12MB:
+ return 0xA;
+ case B43_OFDM_RATE_18MB:
+ return 0xE;
+ case B43_OFDM_RATE_24MB:
+ return 0x9;
+ case B43_OFDM_RATE_36MB:
+ return 0xD;
+ case B43_OFDM_RATE_48MB:
+ return 0x8;
+ case B43_OFDM_RATE_54MB:
+ return 0xC;
+ }
+ B43_WARN_ON(1);
+ return 0;
+}
+
+void b43_generate_plcp_hdr(struct b43_plcp_hdr4 *plcp,
+ const u16 octets, const u8 bitrate)
+{
+ __le32 *data = &(plcp->data);
+ __u8 *raw = plcp->raw;
+
+ if (b43_is_ofdm_rate(bitrate)) {
+ *data = b43_plcp_get_ratecode_ofdm(bitrate);
+ B43_WARN_ON(octets & 0xF000);
+ *data |= (octets << 5);
+ *data = cpu_to_le32(*data);
+ } else {
+ u32 plen;
+
+ plen = octets * 16 / bitrate;
+ if ((octets * 16 % bitrate) > 0) {
+ plen++;
+ if ((bitrate == B43_CCK_RATE_11MB)
+ && ((octets * 8 % 11) < 4)) {
+ raw[1] = 0x84;
+ } else
+ raw[1] = 0x04;
+ } else
+ raw[1] = 0x04;
+ *data |= cpu_to_le32(plen << 16);
+ raw[0] = b43_plcp_get_ratecode_cck(bitrate);
+ }
+}
+
+static u8 b43_calc_fallback_rate(u8 bitrate)
+{
+ switch (bitrate) {
+ case B43_CCK_RATE_1MB:
+ return B43_CCK_RATE_1MB;
+ case B43_CCK_RATE_2MB:
+ return B43_CCK_RATE_1MB;
+ case B43_CCK_RATE_5MB:
+ return B43_CCK_RATE_2MB;
+ case B43_CCK_RATE_11MB:
+ return B43_CCK_RATE_5MB;
+ case B43_OFDM_RATE_6MB:
+ return B43_CCK_RATE_5MB;
+ case B43_OFDM_RATE_9MB:
+ return B43_OFDM_RATE_6MB;
+ case B43_OFDM_RATE_12MB:
+ return B43_OFDM_RATE_9MB;
+ case B43_OFDM_RATE_18MB:
+ return B43_OFDM_RATE_12MB;
+ case B43_OFDM_RATE_24MB:
+ return B43_OFDM_RATE_18MB;
+ case B43_OFDM_RATE_36MB:
+ return B43_OFDM_RATE_24MB;
+ case B43_OFDM_RATE_48MB:
+ return B43_OFDM_RATE_36MB;
+ case B43_OFDM_RATE_54MB:
+ return B43_OFDM_RATE_48MB;
+ }
+ B43_WARN_ON(1);
+ return 0;
+}
+
+static void generate_txhdr_fw4(struct b43_wldev *dev,
+ struct b43_txhdr_fw4 *txhdr,
+ const unsigned char *fragment_data,
+ unsigned int fragment_len,
+ const struct ieee80211_tx_control *txctl,
+ u16 cookie)
+{
+ const struct b43_phy *phy = &dev->phy;
+ const struct ieee80211_hdr *wlhdr =
+ (const struct ieee80211_hdr *)fragment_data;
+ int use_encryption = (!(txctl->flags & IEEE80211_TXCTL_DO_NOT_ENCRYPT));
+ u16 fctl = le16_to_cpu(wlhdr->frame_control);
+ u8 rate, rate_fb;
+ int rate_ofdm, rate_fb_ofdm;
+ unsigned int plcp_fragment_len;
+ u32 mac_ctl = 0;
+ u16 phy_ctl = 0;
+ u8 extra_ft = 0;
+
+ memset(txhdr, 0, sizeof(*txhdr));
+
+ rate = txctl->tx_rate;
+ rate_ofdm = b43_is_ofdm_rate(rate);
+ rate_fb = (txctl->alt_retry_rate == -1) ? rate : txctl->alt_retry_rate;
+ rate_fb_ofdm = b43_is_ofdm_rate(rate_fb);
+
+ if (rate_ofdm)
+ txhdr->phy_rate = b43_plcp_get_ratecode_ofdm(rate);
+ else
+ txhdr->phy_rate = b43_plcp_get_ratecode_cck(rate);
+ txhdr->mac_frame_ctl = wlhdr->frame_control;
+ memcpy(txhdr->tx_receiver, wlhdr->addr1, 6);
+
+ /* Calculate duration for fallback rate */
+ if ((rate_fb == rate) ||
+ (wlhdr->duration_id & cpu_to_le16(0x8000)) ||
+ (wlhdr->duration_id == cpu_to_le16(0))) {
+ /* If the fallback rate equals the normal rate or the
+ * dur_id field contains an AID, CFP magic or 0,
+ * use the original dur_id field. */
+ txhdr->dur_fb = wlhdr->duration_id;
+ } else {
+ int fbrate_base100kbps = B43_RATE_TO_BASE100KBPS(rate_fb);
+ txhdr->dur_fb = ieee80211_generic_frame_duration(dev->wl->hw,
+ dev->wl->if_id,
+ fragment_len,
+ fbrate_base100kbps);
+ }
+
+ plcp_fragment_len = fragment_len + FCS_LEN;
+ if (use_encryption) {
+ u8 key_idx = (u16) (txctl->key_idx);
+ struct b43_key *key;
+ int wlhdr_len;
+ size_t iv_len;
+
+ B43_WARN_ON(key_idx >= dev->max_nr_keys);
+ key = &(dev->key[key_idx]);
+ B43_WARN_ON(!key->keyconf);
+
+ /* Hardware appends ICV. */
+ plcp_fragment_len += txctl->icv_len;
+
+ key_idx = b43_kidx_to_fw(dev, key_idx);
+ mac_ctl |= (key_idx << B43_TX4_MAC_KEYIDX_SHIFT) &
+ B43_TX4_MAC_KEYIDX;
+ mac_ctl |= (key->algorithm << B43_TX4_MAC_KEYALG_SHIFT) &
+ B43_TX4_MAC_KEYALG;
+ wlhdr_len = ieee80211_get_hdrlen(fctl);
+ iv_len = min((size_t) txctl->iv_len,
+ ARRAY_SIZE(txhdr->iv));
+ memcpy(txhdr->iv, ((u8 *) wlhdr) + wlhdr_len, iv_len);
+ }
+ b43_generate_plcp_hdr((struct b43_plcp_hdr4 *)(&txhdr->plcp),
+ plcp_fragment_len, rate);
+ b43_generate_plcp_hdr((struct b43_plcp_hdr4 *)(&txhdr->plcp_fb),
+ plcp_fragment_len, rate_fb);
+
+ /* Extra Frame Types */
+ if (rate_fb_ofdm)
+ extra_ft |= B43_TX4_EFT_FBOFDM;
+
+ /* Set channel radio code. Note that the micrcode ORs 0x100 to
+ * this value before comparing it to the value in SHM, if this
+ * is a 5Ghz packet.
+ */
+ txhdr->chan_radio_code = phy->channel;
+
+ /* PHY TX Control word */
+ if (rate_ofdm)
+ phy_ctl |= B43_TX4_PHY_OFDM;
+ if (dev->short_preamble)
+ phy_ctl |= B43_TX4_PHY_SHORTPRMBL;
+ switch (txctl->antenna_sel_tx) {
+ case 0:
+ phy_ctl |= B43_TX4_PHY_ANTLAST;
+ break;
+ case 1:
+ phy_ctl |= B43_TX4_PHY_ANT0;
+ break;
+ case 2:
+ phy_ctl |= B43_TX4_PHY_ANT1;
+ break;
+ default:
+ B43_WARN_ON(1);
+ }
+
+ /* MAC control */
+ if (!(txctl->flags & IEEE80211_TXCTL_NO_ACK))
+ mac_ctl |= B43_TX4_MAC_ACK;
+ if (!(((fctl & IEEE80211_FCTL_FTYPE) == IEEE80211_FTYPE_CTL) &&
+ ((fctl & IEEE80211_FCTL_STYPE) == IEEE80211_STYPE_PSPOLL)))
+ mac_ctl |= B43_TX4_MAC_HWSEQ;
+ if (txctl->flags & IEEE80211_TXCTL_FIRST_FRAGMENT)
+ mac_ctl |= B43_TX4_MAC_STMSDU;
+ if (phy->type == B43_PHYTYPE_A)
+ mac_ctl |= B43_TX4_MAC_5GHZ;
+
+ /* Generate the RTS or CTS-to-self frame */
+ if ((txctl->flags & IEEE80211_TXCTL_USE_RTS_CTS) ||
+ (txctl->flags & IEEE80211_TXCTL_USE_CTS_PROTECT)) {
+ unsigned int len;
+ struct ieee80211_hdr *hdr;
+ int rts_rate, rts_rate_fb;
+ int rts_rate_ofdm, rts_rate_fb_ofdm;
+
+ rts_rate = txctl->rts_cts_rate;
+ rts_rate_ofdm = b43_is_ofdm_rate(rts_rate);
+ rts_rate_fb = b43_calc_fallback_rate(rts_rate);
+ rts_rate_fb_ofdm = b43_is_ofdm_rate(rts_rate_fb);
+
+ if (txctl->flags & IEEE80211_TXCTL_USE_CTS_PROTECT) {
+ ieee80211_ctstoself_get(dev->wl->hw, dev->wl->if_id,
+ fragment_data, fragment_len,
+ txctl,
+ (struct ieee80211_cts *)(txhdr->
+ rts_frame));
+ mac_ctl |= B43_TX4_MAC_SENDCTS;
+ len = sizeof(struct ieee80211_cts);
+ } else {
+ ieee80211_rts_get(dev->wl->hw, dev->wl->if_id,
+ fragment_data, fragment_len, txctl,
+ (struct ieee80211_rts *)(txhdr->
+ rts_frame));
+ mac_ctl |= B43_TX4_MAC_SENDRTS;
+ len = sizeof(struct ieee80211_rts);
+ }
+ len += FCS_LEN;
+ b43_generate_plcp_hdr((struct b43_plcp_hdr4 *)(&txhdr->
+ rts_plcp), len,
+ rts_rate);
+ b43_generate_plcp_hdr((struct b43_plcp_hdr4 *)(&txhdr->
+ rts_plcp_fb),
+ len, rts_rate_fb);
+ hdr = (struct ieee80211_hdr *)(&txhdr->rts_frame);
+ txhdr->rts_dur_fb = hdr->duration_id;
+ if (rts_rate_ofdm) {
+ extra_ft |= B43_TX4_EFT_RTSOFDM;
+ txhdr->phy_rate_rts =
+ b43_plcp_get_ratecode_ofdm(rts_rate);
+ } else
+ txhdr->phy_rate_rts =
+ b43_plcp_get_ratecode_cck(rts_rate);
+ if (rts_rate_fb_ofdm)
+ extra_ft |= B43_TX4_EFT_RTSFBOFDM;
+ mac_ctl |= B43_TX4_MAC_LONGFRAME;
+ }
+
+ /* Magic cookie */
+ txhdr->cookie = cpu_to_le16(cookie);
+
+ /* Apply the bitfields */
+ txhdr->mac_ctl = cpu_to_le32(mac_ctl);
+ txhdr->phy_ctl = cpu_to_le16(phy_ctl);
+ txhdr->extra_ft = extra_ft;
+}
+
+void b43_generate_txhdr(struct b43_wldev *dev,
+ u8 * txhdr,
+ const unsigned char *fragment_data,
+ unsigned int fragment_len,
+ const struct ieee80211_tx_control *txctl, u16 cookie)
+{
+ generate_txhdr_fw4(dev, (struct b43_txhdr_fw4 *)txhdr,
+ fragment_data, fragment_len, txctl, cookie);
+}
+
+static s8 b43_rssi_postprocess(struct b43_wldev *dev,
+ u8 in_rssi, int ofdm,
+ int adjust_2053, int adjust_2050)
+{
+ struct b43_phy *phy = &dev->phy;
+ s32 tmp;
+
+ switch (phy->radio_ver) {
+ case 0x2050:
+ if (ofdm) {
+ tmp = in_rssi;
+ if (tmp > 127)
+ tmp -= 256;
+ tmp *= 73;
+ tmp /= 64;
+ if (adjust_2050)
+ tmp += 25;
+ else
+ tmp -= 3;
+ } else {
+ if (dev->dev->bus->sprom.r1.
+ boardflags_lo & B43_BFL_RSSI) {
+ if (in_rssi > 63)
+ in_rssi = 63;
+ tmp = phy->nrssi_lt[in_rssi];
+ tmp = 31 - tmp;
+ tmp *= -131;
+ tmp /= 128;
+ tmp -= 57;
+ } else {
+ tmp = in_rssi;
+ tmp = 31 - tmp;
+ tmp *= -149;
+ tmp /= 128;
+ tmp -= 68;
+ }
+ if (phy->type == B43_PHYTYPE_G && adjust_2050)
+ tmp += 25;
+ }
+ break;
+ case 0x2060:
+ if (in_rssi > 127)
+ tmp = in_rssi - 256;
+ else
+ tmp = in_rssi;
+ break;
+ default:
+ tmp = in_rssi;
+ tmp -= 11;
+ tmp *= 103;
+ tmp /= 64;
+ if (adjust_2053)
+ tmp -= 109;
+ else
+ tmp -= 83;
+ }
+
+ return (s8) tmp;
+}
+
+//TODO
+#if 0
+static s8 b43_rssinoise_postprocess(struct b43_wldev *dev, u8 in_rssi)
+{
+ struct b43_phy *phy = &dev->phy;
+ s8 ret;
+
+ if (phy->type == B43_PHYTYPE_A) {
+ //TODO: Incomplete specs.
+ ret = 0;
+ } else
+ ret = b43_rssi_postprocess(dev, in_rssi, 0, 1, 1);
+
+ return ret;
+}
+#endif
+
+void b43_rx(struct b43_wldev *dev, struct sk_buff *skb, const void *_rxhdr)
+{
+ struct ieee80211_rx_status status;
+ struct b43_plcp_hdr6 *plcp;
+ struct ieee80211_hdr *wlhdr;
+ const struct b43_rxhdr_fw4 *rxhdr = _rxhdr;
+ u16 fctl;
+ u16 phystat0, phystat3, chanstat, mactime;
+ u32 macstat;
+ u16 chanid;
+ u8 jssi;
+ int padding;
+
+ memset(&status, 0, sizeof(status));
+
+ /* Get metadata about the frame from the header. */
+ phystat0 = le16_to_cpu(rxhdr->phy_status0);
+ phystat3 = le16_to_cpu(rxhdr->phy_status3);
+ jssi = rxhdr->jssi;
+ macstat = le32_to_cpu(rxhdr->mac_status);
+ mactime = le16_to_cpu(rxhdr->mac_time);
+ chanstat = le16_to_cpu(rxhdr->channel);
+
+ if (macstat & B43_RX_MAC_FCSERR)
+ dev->wl->ieee_stats.dot11FCSErrorCount++;
+ if (macstat & B43_RX_MAC_DECERR) {
+ /* Decryption with the given key failed.
+ * Drop the packet. We also won't be able to decrypt it with
+ * the key in software. */
+ goto drop;
+ }
+
+ /* Skip PLCP and padding */
+ padding = (macstat & B43_RX_MAC_PADDING) ? 2 : 0;
+ if (unlikely(skb->len < (sizeof(struct b43_plcp_hdr6) + padding))) {
+ b43dbg(dev->wl, "RX: Packet size underrun (1)\n");
+ goto drop;
+ }
+ plcp = (struct b43_plcp_hdr6 *)(skb->data + padding);
+ skb_pull(skb, sizeof(struct b43_plcp_hdr6) + padding);
+ /* The skb contains the Wireless Header + payload data now */
+ if (unlikely(skb->len < (2 + 2 + 6 /*minimum hdr */ + FCS_LEN))) {
+ b43dbg(dev->wl, "RX: Packet size underrun (2)\n");
+ goto drop;
+ }
+ wlhdr = (struct ieee80211_hdr *)(skb->data);
+ fctl = le16_to_cpu(wlhdr->frame_control);
+ skb_trim(skb, skb->len - FCS_LEN);
+
+ if (macstat & B43_RX_MAC_DEC) {
+ unsigned int keyidx;
+ int wlhdr_len;
+
+ keyidx = ((macstat & B43_RX_MAC_KEYIDX)
+ >> B43_RX_MAC_KEYIDX_SHIFT);
+ /* We must adjust the key index here. We want the "physical"
+ * key index, but the ucode passed it slightly different.
+ */
+ keyidx = b43_kidx_to_raw(dev, keyidx);
+ B43_WARN_ON(keyidx >= dev->max_nr_keys);
+
+ if (dev->key[keyidx].algorithm != B43_SEC_ALGO_NONE) {
+ wlhdr_len = ieee80211_get_hdrlen(fctl);
+ if (unlikely(skb->len < (wlhdr_len + 3))) {
+ b43dbg(dev->wl,
+ "RX: Packet size underrun (3)\n");
+ goto drop;
+ }
+ status.flag |= RX_FLAG_DECRYPTED;
+ }
+ }
+
+ status.ssi = b43_rssi_postprocess(dev, jssi,
+ (phystat0 & B43_RX_PHYST0_OFDM),
+ (phystat0 & B43_RX_PHYST0_GAINCTL),
+ (phystat3 & B43_RX_PHYST3_TRSTATE));
+ status.noise = dev->stats.link_noise;
+ /* the next line looks wrong, but is what mac80211 wants */
+ status.signal = (jssi * 100) / B43_RX_MAX_SSI;
+ if (phystat0 & B43_RX_PHYST0_OFDM)
+ status.rate = b43_plcp_get_bitrate_ofdm(plcp);
+ else
+ status.rate = b43_plcp_get_bitrate_cck(plcp);
+ status.antenna = !!(phystat0 & B43_RX_PHYST0_ANT);
+ status.mactime = mactime;
+
+ chanid = (chanstat & B43_RX_CHAN_ID) >> B43_RX_CHAN_ID_SHIFT;
+ switch (chanstat & B43_RX_CHAN_PHYTYPE) {
+ case B43_PHYTYPE_A:
+ status.phymode = MODE_IEEE80211A;
+ status.freq = chanid;
+ status.channel = b43_freq_to_channel_a(chanid);
+ break;
+ case B43_PHYTYPE_B:
+ status.phymode = MODE_IEEE80211B;
+ status.freq = chanid + 2400;
+ status.channel = b43_freq_to_channel_bg(chanid + 2400);
+ break;
+ case B43_PHYTYPE_G:
+ status.phymode = MODE_IEEE80211G;
+ status.freq = chanid + 2400;
+ status.channel = b43_freq_to_channel_bg(chanid + 2400);
+ break;
+ default:
+ B43_WARN_ON(1);
+ }
+
+ dev->stats.last_rx = jiffies;
+ ieee80211_rx_irqsafe(dev->wl->hw, skb, &status);
+
+ return;
+drop:
+ b43dbg(dev->wl, "RX: Packet dropped\n");
+ dev_kfree_skb_any(skb);
+}
+
+void b43_handle_txstatus(struct b43_wldev *dev,
+ const struct b43_txstatus *status)
+{
+ b43_debugfs_log_txstat(dev, status);
+
+ if (status->intermediate)
+ return;
+ if (status->for_ampdu)
+ return;
+ if (!status->acked)
+ dev->wl->ieee_stats.dot11ACKFailureCount++;
+ if (status->rts_count) {
+ if (status->rts_count == 0xF) //FIXME
+ dev->wl->ieee_stats.dot11RTSFailureCount++;
+ else
+ dev->wl->ieee_stats.dot11RTSSuccessCount++;
+ }
+
+ if (b43_using_pio(dev))
+ b43_pio_handle_txstatus(dev, status);
+ else
+ b43_dma_handle_txstatus(dev, status);
+}
+
+/* Handle TX status report as received through DMA/PIO queues */
+void b43_handle_hwtxstatus(struct b43_wldev *dev,
+ const struct b43_hwtxstatus *hw)
+{
+ struct b43_txstatus status;
+ u8 tmp;
+
+ status.cookie = le16_to_cpu(hw->cookie);
+ status.seq = le16_to_cpu(hw->seq);
+ status.phy_stat = hw->phy_stat;
+ tmp = hw->count;
+ status.frame_count = (tmp >> 4);
+ status.rts_count = (tmp & 0x0F);
+ tmp = hw->flags;
+ status.supp_reason = ((tmp & 0x1C) >> 2);
+ status.pm_indicated = !!(tmp & 0x80);
+ status.intermediate = !!(tmp & 0x40);
+ status.for_ampdu = !!(tmp & 0x20);
+ status.acked = !!(tmp & 0x02);
+
+ b43_handle_txstatus(dev, &status);
+}
+
+/* Stop any TX operation on the device (suspend the hardware queues) */
+void b43_tx_suspend(struct b43_wldev *dev)
+{
+ if (b43_using_pio(dev))
+ b43_pio_freeze_txqueues(dev);
+ else
+ b43_dma_tx_suspend(dev);
+}
+
+/* Resume any TX operation on the device (resume the hardware queues) */
+void b43_tx_resume(struct b43_wldev *dev)
+{
+ if (b43_using_pio(dev))
+ b43_pio_thaw_txqueues(dev);
+ else
+ b43_dma_tx_resume(dev);
+}
+
+#if 0
+static void upload_qos_parms(struct b43_wldev *dev,
+ const u16 * parms, u16 offset)
+{
+ int i;
+
+ for (i = 0; i < B43_NR_QOSPARMS; i++) {
+ b43_shm_write16(dev, B43_SHM_SHARED,
+ offset + (i * 2), parms[i]);
+ }
+}
+#endif
+
+/* Initialize the QoS parameters */
+void b43_qos_init(struct b43_wldev *dev)
+{
+ /* FIXME: This function must probably be called from the mac80211
+ * config callback. */
+ return;
+
+ b43_hf_write(dev, b43_hf_read(dev) | B43_HF_EDCF);
+ //FIXME kill magic
+ b43_write16(dev, 0x688, b43_read16(dev, 0x688) | 0x4);
+
+ /*TODO: We might need some stack support here to get the values. */
+}
--- /dev/null
+#ifndef B43_XMIT_H_
+#define B43_XMIT_H_
+
+#include "main.h"
+
+#define _b43_declare_plcp_hdr(size) \
+ struct b43_plcp_hdr##size { \
+ union { \
+ __le32 data; \
+ __u8 raw[size]; \
+ } __attribute__((__packed__)); \
+ } __attribute__((__packed__))
+
+/* struct b43_plcp_hdr4 */
+_b43_declare_plcp_hdr(4);
+/* struct b43_plcp_hdr6 */
+_b43_declare_plcp_hdr(6);
+
+#undef _b43_declare_plcp_hdr
+
+/* TX header for v4 firmware */
+struct b43_txhdr_fw4 {
+ __le32 mac_ctl; /* MAC TX control */
+ __le16 mac_frame_ctl; /* Copy of the FrameControl field */
+ __le16 tx_fes_time_norm; /* TX FES Time Normal */
+ __le16 phy_ctl; /* PHY TX control */
+ __le16 phy_ctl_0; /* Unused */
+ __le16 phy_ctl_1; /* Unused */
+ __le16 phy_ctl_rts_0; /* Unused */
+ __le16 phy_ctl_rts_1; /* Unused */
+ __u8 phy_rate; /* PHY rate */
+ __u8 phy_rate_rts; /* PHY rate for RTS/CTS */
+ __u8 extra_ft; /* Extra Frame Types */
+ __u8 chan_radio_code; /* Channel Radio Code */
+ __u8 iv[16]; /* Encryption IV */
+ __u8 tx_receiver[6]; /* TX Frame Receiver address */
+ __le16 tx_fes_time_fb; /* TX FES Time Fallback */
+ struct b43_plcp_hdr6 rts_plcp_fb; /* RTS fallback PLCP */
+ __le16 rts_dur_fb; /* RTS fallback duration */
+ struct b43_plcp_hdr6 plcp_fb; /* Fallback PLCP */
+ __le16 dur_fb; /* Fallback duration */
+ __le16 mm_dur_time; /* Unused */
+ __le16 mm_dur_time_fb; /* Unused */
+ __le32 time_stamp; /* Timestamp */
+ PAD_BYTES(2);
+ __le16 cookie; /* TX frame cookie */
+ __le16 tx_status; /* TX status */
+ struct b43_plcp_hdr6 rts_plcp; /* RTS PLCP */
+ __u8 rts_frame[16]; /* The RTS frame (if used) */
+ PAD_BYTES(2);
+ struct b43_plcp_hdr6 plcp; /* Main PLCP */
+} __attribute__ ((__packed__));
+
+/* MAC TX control */
+#define B43_TX4_MAC_KEYIDX 0x0FF00000 /* Security key index */
+#define B43_TX4_MAC_KEYIDX_SHIFT 20
+#define B43_TX4_MAC_KEYALG 0x00070000 /* Security key algorithm */
+#define B43_TX4_MAC_KEYALG_SHIFT 16
+#define B43_TX4_MAC_LIFETIME 0x00001000
+#define B43_TX4_MAC_FRAMEBURST 0x00000800
+#define B43_TX4_MAC_SENDCTS 0x00000400
+#define B43_TX4_MAC_AMPDU 0x00000300
+#define B43_TX4_MAC_AMPDU_SHIFT 8
+#define B43_TX4_MAC_5GHZ 0x00000080
+#define B43_TX4_MAC_IGNPMQ 0x00000020
+#define B43_TX4_MAC_HWSEQ 0x00000010 /* Use Hardware Sequence Number */
+#define B43_TX4_MAC_STMSDU 0x00000008 /* Start MSDU */
+#define B43_TX4_MAC_SENDRTS 0x00000004
+#define B43_TX4_MAC_LONGFRAME 0x00000002
+#define B43_TX4_MAC_ACK 0x00000001
+
+/* Extra Frame Types */
+#define B43_TX4_EFT_FBOFDM 0x0001 /* Data frame fallback rate type */
+#define B43_TX4_EFT_RTSOFDM 0x0004 /* RTS/CTS rate type */
+#define B43_TX4_EFT_RTSFBOFDM 0x0010 /* RTS/CTS fallback rate type */
+
+/* PHY TX control word */
+#define B43_TX4_PHY_OFDM 0x0001 /* Data frame rate type */
+#define B43_TX4_PHY_SHORTPRMBL 0x0010 /* Use short preamble */
+#define B43_TX4_PHY_ANT 0x03C0 /* Antenna selection */
+#define B43_TX4_PHY_ANT0 0x0000 /* Use antenna 0 */
+#define B43_TX4_PHY_ANT1 0x0100 /* Use antenna 1 */
+#define B43_TX4_PHY_ANTLAST 0x0300 /* Use last used antenna */
+
+void b43_generate_txhdr(struct b43_wldev *dev,
+ u8 * txhdr,
+ const unsigned char *fragment_data,
+ unsigned int fragment_len,
+ const struct ieee80211_tx_control *txctl, u16 cookie);
+
+/* Transmit Status */
+struct b43_txstatus {
+ u16 cookie; /* The cookie from the txhdr */
+ u16 seq; /* Sequence number */
+ u8 phy_stat; /* PHY TX status */
+ u8 frame_count; /* Frame transmit count */
+ u8 rts_count; /* RTS transmit count */
+ u8 supp_reason; /* Suppression reason */
+ /* flags */
+ u8 pm_indicated; /* PM mode indicated to AP */
+ u8 intermediate; /* Intermediate status notification (not final) */
+ u8 for_ampdu; /* Status is for an AMPDU (afterburner) */
+ u8 acked; /* Wireless ACK received */
+};
+
+/* txstatus supp_reason values */
+enum {
+ B43_TXST_SUPP_NONE, /* Not suppressed */
+ B43_TXST_SUPP_PMQ, /* Suppressed due to PMQ entry */
+ B43_TXST_SUPP_FLUSH, /* Suppressed due to flush request */
+ B43_TXST_SUPP_PREV, /* Previous fragment failed */
+ B43_TXST_SUPP_CHAN, /* Channel mismatch */
+ B43_TXST_SUPP_LIFE, /* Lifetime expired */
+ B43_TXST_SUPP_UNDER, /* Buffer underflow */
+ B43_TXST_SUPP_ABNACK, /* Afterburner NACK */
+};
+
+/* Transmit Status as received through DMA/PIO on old chips */
+struct b43_hwtxstatus {
+ PAD_BYTES(4);
+ __le16 cookie;
+ u8 flags;
+ u8 count;
+ PAD_BYTES(2);
+ __le16 seq;
+ u8 phy_stat;
+ PAD_BYTES(1);
+} __attribute__ ((__packed__));
+
+/* Receive header for v4 firmware. */
+struct b43_rxhdr_fw4 {
+ __le16 frame_len; /* Frame length */
+ PAD_BYTES(2);
+ __le16 phy_status0; /* PHY RX Status 0 */
+ __u8 jssi; /* PHY RX Status 1: JSSI */
+ __u8 sig_qual; /* PHY RX Status 1: Signal Quality */
+ __le16 phy_status2; /* PHY RX Status 2 */
+ __le16 phy_status3; /* PHY RX Status 3 */
+ __le32 mac_status; /* MAC RX status */
+ __le16 mac_time;
+ __le16 channel;
+} __attribute__ ((__packed__));
+
+/* PHY RX Status 0 */
+#define B43_RX_PHYST0_GAINCTL 0x4000 /* Gain Control */
+#define B43_RX_PHYST0_PLCPHCF 0x0200
+#define B43_RX_PHYST0_PLCPFV 0x0100
+#define B43_RX_PHYST0_SHORTPRMBL 0x0080 /* Received with Short Preamble */
+#define B43_RX_PHYST0_LCRS 0x0040
+#define B43_RX_PHYST0_ANT 0x0020 /* Antenna */
+#define B43_RX_PHYST0_UNSRATE 0x0010
+#define B43_RX_PHYST0_CLIP 0x000C
+#define B43_RX_PHYST0_CLIP_SHIFT 2
+#define B43_RX_PHYST0_FTYPE 0x0003 /* Frame type */
+#define B43_RX_PHYST0_CCK 0x0000 /* Frame type: CCK */
+#define B43_RX_PHYST0_OFDM 0x0001 /* Frame type: OFDM */
+#define B43_RX_PHYST0_PRE_N 0x0002 /* Pre-standard N-PHY frame */
+#define B43_RX_PHYST0_STD_N 0x0003 /* Standard N-PHY frame */
+
+/* PHY RX Status 2 */
+#define B43_RX_PHYST2_LNAG 0xC000 /* LNA Gain */
+#define B43_RX_PHYST2_LNAG_SHIFT 14
+#define B43_RX_PHYST2_PNAG 0x3C00 /* PNA Gain */
+#define B43_RX_PHYST2_PNAG_SHIFT 10
+#define B43_RX_PHYST2_FOFF 0x03FF /* F offset */
+
+/* PHY RX Status 3 */
+#define B43_RX_PHYST3_DIGG 0x1800 /* DIG Gain */
+#define B43_RX_PHYST3_DIGG_SHIFT 11
+#define B43_RX_PHYST3_TRSTATE 0x0400 /* TR state */
+
+/* MAC RX Status */
+#define B43_RX_MAC_BEACONSENT 0x00008000 /* Beacon send flag */
+#define B43_RX_MAC_KEYIDX 0x000007E0 /* Key index */
+#define B43_RX_MAC_KEYIDX_SHIFT 5
+#define B43_RX_MAC_DECERR 0x00000010 /* Decrypt error */
+#define B43_RX_MAC_DEC 0x00000008 /* Decryption attempted */
+#define B43_RX_MAC_PADDING 0x00000004 /* Pad bytes present */
+#define B43_RX_MAC_RESP 0x00000002 /* Response frame transmitted */
+#define B43_RX_MAC_FCSERR 0x00000001 /* FCS error */
+
+/* RX channel */
+#define B43_RX_CHAN_GAIN 0xFC00 /* Gain */
+#define B43_RX_CHAN_GAIN_SHIFT 10
+#define B43_RX_CHAN_ID 0x03FC /* Channel ID */
+#define B43_RX_CHAN_ID_SHIFT 2
+#define B43_RX_CHAN_PHYTYPE 0x0003 /* PHY type */
+
+u8 b43_plcp_get_ratecode_cck(const u8 bitrate);
+u8 b43_plcp_get_ratecode_ofdm(const u8 bitrate);
+
+void b43_generate_plcp_hdr(struct b43_plcp_hdr4 *plcp,
+ const u16 octets, const u8 bitrate);
+
+void b43_rx(struct b43_wldev *dev, struct sk_buff *skb, const void *_rxhdr);
+
+void b43_handle_txstatus(struct b43_wldev *dev,
+ const struct b43_txstatus *status);
+
+void b43_handle_hwtxstatus(struct b43_wldev *dev,
+ const struct b43_hwtxstatus *hw);
+
+void b43_tx_suspend(struct b43_wldev *dev);
+void b43_tx_resume(struct b43_wldev *dev);
+
+#define B43_NR_QOSPARMS 22
+enum {
+ B43_QOSPARM_TXOP = 0,
+ B43_QOSPARM_CWMIN,
+ B43_QOSPARM_CWMAX,
+ B43_QOSPARM_CWCUR,
+ B43_QOSPARM_AIFS,
+ B43_QOSPARM_BSLOTS,
+ B43_QOSPARM_REGGAP,
+ B43_QOSPARM_STATUS,
+};
+void b43_qos_init(struct b43_wldev *dev);
+
+/* Helper functions for converting the key-table index from "firmware-format"
+ * to "raw-format" and back. The firmware API changed for this at some revision.
+ * We need to account for that here. */
+static inline int b43_new_kidx_api(struct b43_wldev *dev)
+{
+ /* FIXME: Not sure the change was at rev 351 */
+ return (dev->fw.rev >= 351);
+}
+static inline u8 b43_kidx_to_fw(struct b43_wldev *dev, u8 raw_kidx)
+{
+ u8 firmware_kidx;
+ if (b43_new_kidx_api(dev)) {
+ firmware_kidx = raw_kidx;
+ } else {
+ if (raw_kidx >= 4) /* Is per STA key? */
+ firmware_kidx = raw_kidx - 4;
+ else
+ firmware_kidx = raw_kidx; /* TX default key */
+ }
+ return firmware_kidx;
+}
+static inline u8 b43_kidx_to_raw(struct b43_wldev *dev, u8 firmware_kidx)
+{
+ u8 raw_kidx;
+ if (b43_new_kidx_api(dev))
+ raw_kidx = firmware_kidx;
+ else
+ raw_kidx = firmware_kidx + 4; /* RX default keys or per STA keys */
+ return raw_kidx;
+}
+
+#endif /* B43_XMIT_H_ */
projects / linux-2.6 / commitdiff