avr32: Add support for ATSTK1006

The ATSTK1006 is basically an upgraded version of ATSTK1002 with
128 MiB SDRAM and 256 MiB NAND flash on board.

Otherwise, the board is very similar to the ATSTK1002, so it uses the
same board support file.

Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

diff --git a/arch/avr32/boards/atstk1000/Kconfig b/arch/avr32/boards/atstk1000/Kconfig
index af90b00100fd0d96f58df404411e00affce02bcd..8dc48214f0b76ffe44c15e2ca5f74a52641a2086 100644 (file)
--- a/arch/avr32/boards/atstk1000/Kconfig
+++ b/arch/avr32/boards/atstk1000/Kconfig
@@ -18,6 +18,10 @@ config BOARD_ATSTK1004
        bool "ATSTK1004"
        select CPU_AT32AP7002
 
+config BOARD_ATSTK1006
+       bool "ATSTK1006"
+       select CPU_AT32AP7000
+
 endchoice
 
 

diff --git a/arch/avr32/boards/atstk1000/Makefile b/arch/avr32/boards/atstk1000/Makefile
index beead86462e8a6a7f8f7797e746be176268394ba..edecee03742d4a935df734e4e86f9d755c7eb8ad 100644 (file)
--- a/arch/avr32/boards/atstk1000/Makefile
+++ b/arch/avr32/boards/atstk1000/Makefile
@@ -2,3 +2,4 @@ obj-y                           += setup.o flash.o
 obj-$(CONFIG_BOARD_ATSTK1002)  += atstk1002.o
 obj-$(CONFIG_BOARD_ATSTK1003)  += atstk1003.o
 obj-$(CONFIG_BOARD_ATSTK1004)  += atstk1004.o
+obj-$(CONFIG_BOARD_ATSTK1006)  += atstk1002.o

diff --git a/arch/avr32/boards/atstk1000/atstk1002.c b/arch/avr32/boards/atstk1000/atstk1002.c
index 000eb4220a12619b4e9b9922f5ed7d9e4c958064..5bfaf4d87b3fdda8d8d03e141d4573d3313914a5 100644 (file)
--- a/arch/avr32/boards/atstk1000/atstk1002.c
+++ b/arch/avr32/boards/atstk1000/atstk1002.c
@@ -1,7 +1,7 @@
 /*
- * ATSTK1002 daughterboard-specific init code
+ * ATSTK1002/ATSTK1006 daughterboard-specific init code
  *
- * Copyright (C) 2005-2006 Atmel Corporation
+ * Copyright (C) 2005-2007 Atmel Corporation
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 as
@@ -29,6 +29,74 @@
 #include "atstk1000.h"
 
 
+/*
+ * The ATSTK1006 daughterboard is very similar to the ATSTK1002. Both
+ * have the AT32AP7000 chip on board; the difference is that the
+ * STK1006 has 128 MB SDRAM (the STK1002 uses the 8 MB SDRAM chip on
+ * the STK1000 motherboard) and 256 MB NAND flash (the STK1002 has
+ * none.)
+ *
+ * The RAM difference is handled by the boot loader, so the only
+ * difference we end up handling here is the NAND flash.
+ */
+#ifdef CONFIG_BOARD_ATSTK1006
+#include <linux/mtd/partitions.h>
+#include <asm/arch/smc.h>
+
+static struct smc_timing nand_timing __initdata = {
+       .ncs_read_setup         = 0,
+       .nrd_setup              = 10,
+       .ncs_write_setup        = 0,
+       .nwe_setup              = 10,
+
+       .ncs_read_pulse         = 30,
+       .nrd_pulse              = 15,
+       .ncs_write_pulse        = 30,
+       .nwe_pulse              = 15,
+
+       .read_cycle             = 30,
+       .write_cycle            = 30,
+
+       .ncs_read_recover       = 0,
+       .nrd_recover            = 15,
+       .ncs_write_recover      = 0,
+       /* WE# high -> RE# low min 60 ns */
+       .nwe_recover            = 50,
+};
+
+static struct smc_config nand_config __initdata = {
+       .bus_width              = 1,
+       .nrd_controlled         = 1,
+       .nwe_controlled         = 1,
+       .nwait_mode             = 0,
+       .byte_write             = 0,
+       .tdf_cycles             = 2,
+       .tdf_mode               = 0,
+};
+
+static struct mtd_partition nand_partitions[] = {
+       {
+               .name           = "main",
+               .offset         = 0x00000000,
+               .size           = MTDPART_SIZ_FULL,
+       },
+};
+
+static struct mtd_partition *nand_part_info(int size, int *num_partitions)
+{
+       *num_partitions = ARRAY_SIZE(nand_partitions);
+       return nand_partitions;
+}
+
+struct atmel_nand_data atstk1006_nand_data __initdata = {
+       .cle            = 21,
+       .ale            = 22,
+       .rdy_pin        = GPIO_PIN_PB(30),
+       .enable_pin     = GPIO_PIN_PB(29),
+       .partition_info = nand_part_info,
+};
+#endif
+
 struct eth_addr {
        u8 addr[6];
 };
@@ -212,6 +280,12 @@ static int __init atstk1002_init(void)
 
        at32_add_system_devices();
 
+#ifdef CONFIG_BOARD_ATSTK1006
+       smc_set_timing(&nand_config, &nand_timing);
+       smc_set_configuration(3, &nand_config);
+       at32_add_device_nand(0, &atstk1006_nand_data);
+#endif
+
 #ifdef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM
        at32_add_device_usart(1);
 #else