--- /dev/null
+/*
+ * MPC885 ADS Device Tree Source
+ *
+ * Copyright 2006 MontaVista Software, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+
+/ {
+ model = "MPC885ADS";
+ compatible = "mpc8xx";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ linux,phandle = <100>;
+
+ cpus {
+ #cpus = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ linux,phandle = <200>;
+
+ PowerPC,885@0 {
+ device_type = "cpu";
+ reg = <0>;
+ d-cache-line-size = <20>; // 32 bytes
+ i-cache-line-size = <20>; // 32 bytes
+ d-cache-size = <2000>; // L1, 8K
+ i-cache-size = <2000>; // L1, 8K
+ timebase-frequency = <0>;
+ bus-frequency = <0>;
+ clock-frequency = <0>;
+ 32-bit;
+ interrupts = <f 2>; // decrementer interrupt
+ interrupt-parent = <ff000000>;
+ linux,phandle = <201>;
+ linux,boot-cpu;
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ linux,phandle = <300>;
+ reg = <00000000 800000>;
+ };
+
+ soc885@ff000000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ #interrupt-cells = <2>;
+ device_type = "soc";
+ ranges = <0 ff000000 00100000>;
+ reg = <ff000000 00000200>;
+ bus-frequency = <0>;
+ mdio@e80 {
+ device_type = "mdio";
+ compatible = "fs_enet";
+ reg = <e80 8>;
+ linux,phandle = <e80>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ ethernet-phy@0 {
+ linux,phandle = <e8000>;
+ reg = <0>;
+ device_type = "ethernet-phy";
+ };
+ ethernet-phy@1 {
+ linux,phandle = <e8001>;
+ reg = <1>;
+ device_type = "ethernet-phy";
+ };
+ ethernet-phy@2 {
+ linux,phandle = <e8002>;
+ reg = <2>;
+ device_type = "ethernet-phy";
+ };
+ };
+
+ fec@e00 {
+ device_type = "network";
+ compatible = "fs_enet";
+ model = "FEC";
+ device-id = <1>;
+ reg = <e00 188>;
+ mac-address = [ 00 00 0C 00 01 FD ];
+ interrupts = <3 1>;
+ interrupt-parent = <ff000000>;
+ phy-handle = <e8000>;
+ };
+
+ fec@1e00 {
+ device_type = "network";
+ compatible = "fs_enet";
+ model = "FEC";
+ device-id = <2>;
+ reg = <1e00 188>;
+ mac-address = [ 00 00 0C 00 02 FD ];
+ interrupts = <7 1>;
+ interrupt-parent = <ff000000>;
+ phy-handle = <e8001>;
+ };
+
+ pic@ff000000 {
+ linux,phandle = <ff000000>;
+ interrupt-controller;
+ #address-cells = <0>;
+ #interrupt-cells = <2>;
+ reg = <0 24>;
+ built-in;
+ device_type = "mpc8xx-pic";
+ compatible = "CPM";
+ };
+
+ cpm@ff000000 {
+ linux,phandle = <ff000000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ #interrupt-cells = <2>;
+ device_type = "cpm";
+ model = "CPM";
+ ranges = <0 0 4000>;
+ reg = <860 f0>;
+ command-proc = <9c0>;
+ brg-frequency = <0>;
+ interrupts = <0 2>; // cpm error interrupt
+ interrupt-parent = <930>;
+
+ pic@930 {
+ linux,phandle = <930>;
+ interrupt-controller;
+ #address-cells = <0>;
+ #interrupt-cells = <2>;
+ interrupts = <5 2 0 2>;
+ interrupt-parent = <ff000000>;
+ reg = <930 20>;
+ built-in;
+ device_type = "cpm-pic";
+ compatible = "CPM";
+ };
+
+ smc@a80 {
+ device_type = "serial";
+ compatible = "cpm_uart";
+ model = "SMC";
+ device-id = <1>;
+ reg = <a80 10 3e80 40>;
+ clock-setup = <00ffffff 0>;
+ rx-clock = <1>;
+ tx-clock = <1>;
+ current-speed = <0>;
+ interrupts = <4 3>;
+ interrupt-parent = <930>;
+ };
+
+ smc@a90 {
+ device_type = "serial";
+ compatible = "cpm_uart";
+ model = "SMC";
+ device-id = <2>;
+ reg = <a90 20 3f80 40>;
+ clock-setup = <ff00ffff 90000>;
+ rx-clock = <2>;
+ tx-clock = <2>;
+ current-speed = <0>;
+ interrupts = <3 3>;
+ interrupt-parent = <930>;
+ };
+
+ scc@a40 {
+ device_type = "network";
+ compatible = "fs_enet";
+ model = "SCC";
+ device-id = <3>;
+ reg = <a40 18 3e00 80>;
+ mac-address = [ 00 00 0C 00 03 FD ];
+ interrupts = <1c 3>;
+ interrupt-parent = <930>;
+ phy-handle = <e8002>;
+ };
+ };
+ };
+};
--- /dev/null
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.19-rc4
+# Fri Nov 10 21:30:40 2006
+#
+# CONFIG_PPC64 is not set
+CONFIG_PPC32=y
+CONFIG_PPC_MERGE=y
+CONFIG_MMU=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_IRQ_PER_CPU=y
+CONFIG_RWSEM_XCHGADD_ALGORITHM=y
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_GENERIC_FIND_NEXT_BIT=y
+CONFIG_PPC=y
+CONFIG_EARLY_PRINTK=y
+CONFIG_GENERIC_NVRAM=y
+CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
+CONFIG_ARCH_MAY_HAVE_PC_FDC=y
+CONFIG_PPC_OF=y
+# CONFIG_PPC_UDBG_16550 is not set
+# CONFIG_GENERIC_TBSYNC is not set
+CONFIG_AUDIT_ARCH=y
+# CONFIG_DEFAULT_UIMAGE is not set
+
+#
+# Processor support
+#
+# CONFIG_CLASSIC32 is not set
+# CONFIG_PPC_52xx is not set
+# CONFIG_PPC_82xx is not set
+# CONFIG_PPC_83xx is not set
+# CONFIG_PPC_85xx is not set
+# CONFIG_PPC_86xx is not set
+CONFIG_PPC_8xx=y
+# CONFIG_40x is not set
+# CONFIG_44x is not set
+# CONFIG_E200 is not set
+CONFIG_8xx=y
+CONFIG_NOT_COHERENT_CACHE=y
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+
+#
+# Code maturity level options
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+
+#
+# General setup
+#
+CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
+# CONFIG_SWAP is not set
+CONFIG_SYSVIPC=y
+# CONFIG_IPC_NS is not set
+# CONFIG_POSIX_MQUEUE is not set
+# CONFIG_BSD_PROCESS_ACCT is not set
+# CONFIG_TASKSTATS is not set
+# CONFIG_UTS_NS is not set
+# CONFIG_AUDIT is not set
+# CONFIG_IKCONFIG is not set
+# CONFIG_RELAY is not set
+CONFIG_INITRAMFS_SOURCE=""
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_SYSCTL=y
+CONFIG_EMBEDDED=y
+# CONFIG_SYSCTL_SYSCALL is not set
+CONFIG_KALLSYMS=y
+# CONFIG_KALLSYMS_EXTRA_PASS is not set
+# CONFIG_HOTPLUG is not set
+CONFIG_PRINTK=y
+# CONFIG_BUG is not set
+CONFIG_ELF_CORE=y
+# CONFIG_BASE_FULL is not set
+CONFIG_FUTEX=y
+# CONFIG_EPOLL is not set
+CONFIG_SHMEM=y
+CONFIG_SLAB=y
+# CONFIG_VM_EVENT_COUNTERS is not set
+CONFIG_RT_MUTEXES=y
+# CONFIG_TINY_SHMEM is not set
+CONFIG_BASE_SMALL=1
+# CONFIG_SLOB is not set
+
+#
+# Loadable module support
+#
+# CONFIG_MODULES is not set
+
+#
+# Block layer
+#
+CONFIG_BLOCK=y
+# CONFIG_LBD is not set
+# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_LSF is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+CONFIG_IOSCHED_AS=y
+CONFIG_IOSCHED_DEADLINE=y
+CONFIG_IOSCHED_CFQ=y
+CONFIG_DEFAULT_AS=y
+# CONFIG_DEFAULT_DEADLINE is not set
+# CONFIG_DEFAULT_CFQ is not set
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="anticipatory"
+# CONFIG_WANT_EARLY_SERIAL is not set
+CONFIG_EMBEDDEDBOOT=y
+# CONFIG_MPIC is not set
+
+#
+# Platform support
+#
+CONFIG_CPM1=y
+# CONFIG_MPC8XXFADS is not set
+# CONFIG_MPC86XADS is not set
+CONFIG_MPC885ADS=y
+
+#
+# MPC8xx CPM Options
+#
+
+#
+# Generic MPC8xx Options
+#
+CONFIG_8xx_COPYBACK=y
+# CONFIG_8xx_CPU6 is not set
+CONFIG_NO_UCODE_PATCH=y
+# CONFIG_USB_SOF_UCODE_PATCH is not set
+# CONFIG_I2C_SPI_UCODE_PATCH is not set
+# CONFIG_I2C_SPI_SMC1_UCODE_PATCH is not set
+
+#
+# Kernel options
+#
+# CONFIG_HIGHMEM is not set
+# CONFIG_HZ_100 is not set
+# CONFIG_HZ_250 is not set
+CONFIG_HZ_1000=y
+CONFIG_HZ=1000
+CONFIG_PREEMPT_NONE=y
+# CONFIG_PREEMPT_VOLUNTARY is not set
+# CONFIG_PREEMPT is not set
+CONFIG_BINFMT_ELF=y
+# CONFIG_BINFMT_MISC is not set
+CONFIG_MATH_EMULATION=y
+CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
+CONFIG_ARCH_FLATMEM_ENABLE=y
+CONFIG_ARCH_POPULATES_NODE_MAP=y
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+# CONFIG_SPARSEMEM_STATIC is not set
+CONFIG_SPLIT_PTLOCK_CPUS=4
+# CONFIG_RESOURCES_64BIT is not set
+# CONFIG_PROC_DEVICETREE is not set
+# CONFIG_CMDLINE_BOOL is not set
+# CONFIG_PM is not set
+# CONFIG_SECCOMP is not set
+CONFIG_ISA_DMA_API=y
+
+#
+# Bus options
+#
+# CONFIG_MPIC_WEIRD is not set
+# CONFIG_PPC_I8259 is not set
+CONFIG_FSL_SOC=y
+# CONFIG_PCI is not set
+# CONFIG_PCI_DOMAINS is not set
+# CONFIG_PCI_QSPAN is not set
+
+#
+# PCCARD (PCMCIA/CardBus) support
+#
+
+#
+# PCI Hotplug Support
+#
+
+#
+# Advanced setup
+#
+# CONFIG_ADVANCED_OPTIONS is not set
+
+#
+# Default settings for advanced configuration options are used
+#
+CONFIG_HIGHMEM_START=0xfe000000
+CONFIG_LOWMEM_SIZE=0x30000000
+CONFIG_KERNEL_START=0xc0000000
+CONFIG_TASK_SIZE=0x80000000
+CONFIG_CONSISTENT_START=0xff100000
+CONFIG_CONSISTENT_SIZE=0x00200000
+CONFIG_BOOT_LOAD=0x00400000
+
+#
+# Networking
+#
+CONFIG_NET=y
+
+#
+# Networking options
+#
+# CONFIG_NETDEBUG is not set
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+CONFIG_XFRM=y
+# CONFIG_XFRM_USER is not set
+# CONFIG_XFRM_SUB_POLICY is not set
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+# CONFIG_IP_PNP_DHCP is not set
+# CONFIG_IP_PNP_BOOTP is not set
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_IP_MROUTE is not set
+# CONFIG_ARPD is not set
+CONFIG_SYN_COOKIES=y
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+# CONFIG_INET_TUNNEL is not set
+CONFIG_INET_XFRM_MODE_TRANSPORT=y
+CONFIG_INET_XFRM_MODE_TUNNEL=y
+CONFIG_INET_XFRM_MODE_BEET=y
+CONFIG_INET_DIAG=y
+CONFIG_INET_TCP_DIAG=y
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_IPV6 is not set
+# CONFIG_INET6_XFRM_TUNNEL is not set
+# CONFIG_INET6_TUNNEL is not set
+# CONFIG_NETWORK_SECMARK is not set
+# CONFIG_NETFILTER is not set
+
+#
+# DCCP Configuration (EXPERIMENTAL)
+#
+# CONFIG_IP_DCCP is not set
+
+#
+# SCTP Configuration (EXPERIMENTAL)
+#
+# CONFIG_IP_SCTP is not set
+
+#
+# TIPC Configuration (EXPERIMENTAL)
+#
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+
+#
+# QoS and/or fair queueing
+#
+# CONFIG_NET_SCHED is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+# CONFIG_IEEE80211 is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+# CONFIG_SYS_HYPERVISOR is not set
+
+#
+# Connector - unified userspace <-> kernelspace linker
+#
+# CONFIG_CONNECTOR is not set
+
+#
+# Memory Technology Devices (MTD)
+#
+# CONFIG_MTD is not set
+
+#
+# Parallel port support
+#
+# CONFIG_PARPORT is not set
+
+#
+# Plug and Play support
+#
+
+#
+# Block devices
+#
+# CONFIG_BLK_DEV_FD is not set
+# CONFIG_BLK_DEV_COW_COMMON is not set
+CONFIG_BLK_DEV_LOOP=y
+# CONFIG_BLK_DEV_CRYPTOLOOP is not set
+# CONFIG_BLK_DEV_NBD is not set
+# CONFIG_BLK_DEV_RAM is not set
+# CONFIG_BLK_DEV_INITRD is not set
+# CONFIG_CDROM_PKTCDVD is not set
+# CONFIG_ATA_OVER_ETH is not set
+
+#
+# Misc devices
+#
+# CONFIG_TIFM_CORE is not set
+
+#
+# ATA/ATAPI/MFM/RLL support
+#
+# CONFIG_IDE is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+# CONFIG_SCSI is not set
+# CONFIG_SCSI_NETLINK is not set
+
+#
+# Serial ATA (prod) and Parallel ATA (experimental) drivers
+#
+# CONFIG_ATA is not set
+
+#
+# Multi-device support (RAID and LVM)
+#
+# CONFIG_MD is not set
+
+#
+# Fusion MPT device support
+#
+# CONFIG_FUSION is not set
+
+#
+# IEEE 1394 (FireWire) support
+#
+
+#
+# I2O device support
+#
+
+#
+# Macintosh device drivers
+#
+# CONFIG_WINDFARM is not set
+
+#
+# Network device support
+#
+CONFIG_NETDEVICES=y
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+
+#
+# PHY device support
+#
+CONFIG_PHYLIB=y
+
+#
+# MII PHY device drivers
+#
+# CONFIG_MARVELL_PHY is not set
+CONFIG_DAVICOM_PHY=y
+# CONFIG_QSEMI_PHY is not set
+# CONFIG_LXT_PHY is not set
+# CONFIG_CICADA_PHY is not set
+# CONFIG_VITESSE_PHY is not set
+# CONFIG_SMSC_PHY is not set
+CONFIG_FIXED_PHY=y
+CONFIG_FIXED_MII_10_FDX=y
+# CONFIG_FIXED_MII_100_FDX is not set
+
+#
+# Ethernet (10 or 100Mbit)
+#
+CONFIG_NET_ETHERNET=y
+CONFIG_MII=y
+# CONFIG_FEC_8XX is not set
+CONFIG_FS_ENET=y
+CONFIG_FS_ENET_HAS_SCC=y
+CONFIG_FS_ENET_HAS_FEC=y
+
+#
+# Ethernet (1000 Mbit)
+#
+
+#
+# Ethernet (10000 Mbit)
+#
+
+#
+# Token Ring devices
+#
+
+#
+# Wireless LAN (non-hamradio)
+#
+# CONFIG_NET_RADIO is not set
+
+#
+# Wan interfaces
+#
+# CONFIG_WAN is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_SHAPER is not set
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+
+#
+# ISDN subsystem
+#
+# CONFIG_ISDN is not set
+
+#
+# Telephony Support
+#
+# CONFIG_PHONE is not set
+
+#
+# Input device support
+#
+CONFIG_INPUT=y
+# CONFIG_INPUT_FF_MEMLESS is not set
+
+#
+# Userland interfaces
+#
+CONFIG_INPUT_MOUSEDEV=y
+CONFIG_INPUT_MOUSEDEV_PSAUX=y
+CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
+CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
+# CONFIG_INPUT_JOYDEV is not set
+# CONFIG_INPUT_TSDEV is not set
+# CONFIG_INPUT_EVDEV is not set
+# CONFIG_INPUT_EVBUG is not set
+
+#
+# Input Device Drivers
+#
+CONFIG_INPUT_KEYBOARD=y
+CONFIG_KEYBOARD_ATKBD=y
+# CONFIG_KEYBOARD_SUNKBD is not set
+# CONFIG_KEYBOARD_LKKBD is not set
+# CONFIG_KEYBOARD_XTKBD is not set
+# CONFIG_KEYBOARD_NEWTON is not set
+# CONFIG_KEYBOARD_STOWAWAY is not set
+CONFIG_INPUT_MOUSE=y
+CONFIG_MOUSE_PS2=y
+# CONFIG_MOUSE_SERIAL is not set
+# CONFIG_MOUSE_VSXXXAA is not set
+# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TOUCHSCREEN is not set
+# CONFIG_INPUT_MISC is not set
+
+#
+# Hardware I/O ports
+#
+CONFIG_SERIO=y
+CONFIG_SERIO_I8042=y
+CONFIG_SERIO_SERPORT=y
+CONFIG_SERIO_LIBPS2=y
+# CONFIG_SERIO_RAW is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+# CONFIG_VT is not set
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+# CONFIG_SERIAL_8250 is not set
+
+#
+# Non-8250 serial port support
+#
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+CONFIG_SERIAL_CPM=y
+CONFIG_SERIAL_CPM_CONSOLE=y
+# CONFIG_SERIAL_CPM_SCC1 is not set
+# CONFIG_SERIAL_CPM_SCC2 is not set
+# CONFIG_SERIAL_CPM_SCC3 is not set
+# CONFIG_SERIAL_CPM_SCC4 is not set
+CONFIG_SERIAL_CPM_SMC1=y
+CONFIG_SERIAL_CPM_SMC2=y
+CONFIG_UNIX98_PTYS=y
+# CONFIG_LEGACY_PTYS is not set
+
+#
+# IPMI
+#
+# CONFIG_IPMI_HANDLER is not set
+
+#
+# Watchdog Cards
+#
+# CONFIG_WATCHDOG is not set
+CONFIG_HW_RANDOM=y
+# CONFIG_NVRAM is not set
+CONFIG_GEN_RTC=y
+# CONFIG_GEN_RTC_X is not set
+# CONFIG_DTLK is not set
+# CONFIG_R3964 is not set
+
+#
+# Ftape, the floppy tape device driver
+#
+# CONFIG_RAW_DRIVER is not set
+
+#
+# TPM devices
+#
+# CONFIG_TCG_TPM is not set
+
+#
+# I2C support
+#
+# CONFIG_I2C is not set
+
+#
+# SPI support
+#
+# CONFIG_SPI is not set
+# CONFIG_SPI_MASTER is not set
+
+#
+# Dallas's 1-wire bus
+#
+# CONFIG_W1 is not set
+
+#
+# Hardware Monitoring support
+#
+CONFIG_HWMON=y
+# CONFIG_HWMON_VID is not set
+# CONFIG_SENSORS_ABITUGURU is not set
+# CONFIG_SENSORS_F71805F is not set
+# CONFIG_SENSORS_VT1211 is not set
+# CONFIG_HWMON_DEBUG_CHIP is not set
+
+#
+# Multimedia devices
+#
+# CONFIG_VIDEO_DEV is not set
+
+#
+# Digital Video Broadcasting Devices
+#
+# CONFIG_DVB is not set
+
+#
+# Graphics support
+#
+CONFIG_FIRMWARE_EDID=y
+# CONFIG_FB is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+
+#
+# Sound
+#
+# CONFIG_SOUND is not set
+
+#
+# USB support
+#
+# CONFIG_USB_ARCH_HAS_HCD is not set
+# CONFIG_USB_ARCH_HAS_OHCI is not set
+# CONFIG_USB_ARCH_HAS_EHCI is not set
+
+#
+# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
+#
+
+#
+# USB Gadget Support
+#
+# CONFIG_USB_GADGET is not set
+
+#
+# MMC/SD Card support
+#
+# CONFIG_MMC is not set
+
+#
+# LED devices
+#
+# CONFIG_NEW_LEDS is not set
+
+#
+# LED drivers
+#
+
+#
+# LED Triggers
+#
+
+#
+# InfiniBand support
+#
+
+#
+# EDAC - error detection and reporting (RAS) (EXPERIMENTAL)
+#
+
+#
+# Real Time Clock
+#
+# CONFIG_RTC_CLASS is not set
+
+#
+# DMA Engine support
+#
+# CONFIG_DMA_ENGINE is not set
+
+#
+# DMA Clients
+#
+
+#
+# DMA Devices
+#
+
+#
+# File systems
+#
+CONFIG_EXT2_FS=y
+CONFIG_EXT2_FS_XATTR=y
+# CONFIG_EXT2_FS_POSIX_ACL is not set
+# CONFIG_EXT2_FS_SECURITY is not set
+# CONFIG_EXT2_FS_XIP is not set
+CONFIG_EXT3_FS=y
+CONFIG_EXT3_FS_XATTR=y
+# CONFIG_EXT3_FS_POSIX_ACL is not set
+# CONFIG_EXT3_FS_SECURITY is not set
+# CONFIG_EXT4DEV_FS is not set
+CONFIG_JBD=y
+# CONFIG_JBD_DEBUG is not set
+CONFIG_FS_MBCACHE=y
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+# CONFIG_FS_POSIX_ACL is not set
+# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
+# CONFIG_OCFS2_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_ROMFS_FS is not set
+CONFIG_INOTIFY=y
+CONFIG_INOTIFY_USER=y
+# CONFIG_QUOTA is not set
+CONFIG_DNOTIFY=y
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+# CONFIG_MSDOS_FS is not set
+# CONFIG_VFAT_FS is not set
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+# CONFIG_PROC_KCORE is not set
+CONFIG_PROC_SYSCTL=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
+# CONFIG_HUGETLB_PAGE is not set
+CONFIG_RAMFS=y
+# CONFIG_CONFIGFS_FS is not set
+
+#
+# Miscellaneous filesystems
+#
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+CONFIG_CRAMFS=y
+# CONFIG_VXFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+
+#
+# Network File Systems
+#
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+# CONFIG_NFS_V3_ACL is not set
+# CONFIG_NFS_V4 is not set
+# CONFIG_NFS_DIRECTIO is not set
+# CONFIG_NFSD is not set
+CONFIG_ROOT_NFS=y
+CONFIG_LOCKD=y
+CONFIG_LOCKD_V4=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+# CONFIG_RPCSEC_GSS_KRB5 is not set
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+# CONFIG_9P_FS is not set
+
+#
+# Partition Types
+#
+CONFIG_PARTITION_ADVANCED=y
+# CONFIG_ACORN_PARTITION is not set
+# CONFIG_OSF_PARTITION is not set
+# CONFIG_AMIGA_PARTITION is not set
+# CONFIG_ATARI_PARTITION is not set
+# CONFIG_MAC_PARTITION is not set
+CONFIG_MSDOS_PARTITION=y
+# CONFIG_BSD_DISKLABEL is not set
+# CONFIG_MINIX_SUBPARTITION is not set
+# CONFIG_SOLARIS_X86_PARTITION is not set
+# CONFIG_UNIXWARE_DISKLABEL is not set
+# CONFIG_LDM_PARTITION is not set
+# CONFIG_SGI_PARTITION is not set
+# CONFIG_ULTRIX_PARTITION is not set
+# CONFIG_SUN_PARTITION is not set
+# CONFIG_KARMA_PARTITION is not set
+# CONFIG_EFI_PARTITION is not set
+
+#
+# Native Language Support
+#
+# CONFIG_NLS is not set
+
+#
+# Library routines
+#
+CONFIG_CRC_CCITT=y
+# CONFIG_CRC16 is not set
+CONFIG_CRC32=y
+# CONFIG_LIBCRC32C is not set
+CONFIG_ZLIB_INFLATE=y
+CONFIG_PLIST=y
+
+#
+# Instrumentation Support
+#
+# CONFIG_PROFILING is not set
+
+#
+# Kernel hacking
+#
+# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_MUST_CHECK=y
+# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_KERNEL is not set
+CONFIG_LOG_BUF_SHIFT=14
+# CONFIG_DEBUG_FS is not set
+# CONFIG_UNWIND_INFO is not set
+# CONFIG_HEADERS_CHECK is not set
+# CONFIG_BOOTX_TEXT is not set
+# CONFIG_PPC_EARLY_DEBUG is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+
+#
+# Cryptographic options
+#
+# CONFIG_CRYPTO is not set
+menu "Platform support"
+ depends on PPC_8xx
+
config FADS
bool
+config CPM1
+ bool
+
choice
prompt "8xx Machine Type"
depends on 8xx
- default RPXLITE
-
-config RPXLITE
- bool "RPX-Lite"
- ---help---
- Single-board computers based around the PowerPC MPC8xx chips and
- intended for embedded applications. The following types are
- supported:
-
- RPX-Lite:
- Embedded Planet RPX Lite. PC104 form-factor SBC based on the MPC823.
-
- RPX-Classic:
- Embedded Planet RPX Classic Low-fat. Credit-card-size SBC based on
- the MPC 860
-
- BSE-IP:
- Bright Star Engineering ip-Engine.
-
- TQM823L:
- TQM850L:
- TQM855L:
- TQM860L:
- MPC8xx based family of mini modules, half credit card size,
- up to 64 MB of RAM, 8 MB Flash, (Fast) Ethernet, 2 x serial ports,
- 2 x CAN bus interface, ...
- Manufacturer: TQ Components, www.tq-group.de
- Date of Release: October (?) 1999
- End of Life: not yet :-)
- URL:
- - module: <http://www.denx.de/PDF/TQM8xxLHWM201.pdf>
- - starter kit: <http://www.denx.de/PDF/STK8xxLHWM201.pdf>
- - images: <http://www.denx.de/embedded-ppc-en.html>
-
- FPS850L:
- FingerPrint Sensor System (based on TQM850L)
- Manufacturer: IKENDI AG, <http://www.ikendi.com/>
- Date of Release: November 1999
- End of life: end 2000 ?
- URL: see TQM850L
-
- IVMS8:
- MPC860 based board used in the "Integrated Voice Mail System",
- Small Version (8 voice channels)
- Manufacturer: Speech Design, <http://www.speech-design.de/>
- Date of Release: December 2000 (?)
- End of life: -
- URL: <http://www.speech-design.de/>
-
- IVML24:
- MPC860 based board used in the "Integrated Voice Mail System",
- Large Version (24 voice channels)
- Manufacturer: Speech Design, <http://www.speech-design.de/>
- Date of Release: March 2001 (?)
- End of life: -
- URL: <http://www.speech-design.de/>
-
- HERMES:
- Hermes-Pro ISDN/LAN router with integrated 8 x hub
- Manufacturer: Multidata Gesellschaft fur Datentechnik und Informatik
- <http://www.multidata.de/>
- Date of Release: 2000 (?)
- End of life: -
- URL: <http://www.multidata.de/english/products/hpro.htm>
-
- IP860:
- VMEBus IP (Industry Pack) carrier board with MPC860
- Manufacturer: MicroSys GmbH, <http://www.microsys.de/>
- Date of Release: ?
- End of life: -
- URL: <http://www.microsys.de/html/ip860.html>
-
- PCU_E:
- PCU = Peripheral Controller Unit, Extended
- Manufacturer: Siemens AG, ICN (Information and Communication Networks)
- <http://www.siemens.de/page/1,3771,224315-1-999_2_226207-0,00.html>
- Date of Release: April 2001
- End of life: August 2001
- URL: n. a.
-
-config RPXCLASSIC
- bool "RPX-Classic"
- help
- The RPX-Classic is a single-board computer based on the Motorola
- MPC860. It features 16MB of DRAM and a variable amount of flash,
- I2C EEPROM, thermal monitoring, a PCMCIA slot, a DIP switch and two
- LEDs. Variants with Ethernet ports exist. Say Y here to support it
- directly.
-
-config BSEIP
- bool "BSE-IP"
- help
- Say Y here to support the Bright Star Engineering ipEngine SBC.
- This is a credit-card-sized device featuring a MPC823 processor,
- 26MB DRAM, 4MB flash, Ethernet, a 16K-gate FPGA, USB, an LCD/video
- controller, and two RS232 ports.
+ default MPC885ADS
config MPC8XXFADS
bool "FADS"
config MPC86XADS
bool "MPC86XADS"
+ select CPM1
help
MPC86x Application Development System by Freescale Semiconductor.
The MPC86xADS is meant to serve as a platform for s/w and h/w
development around the MPC86X processor families.
- select FADS
config MPC885ADS
bool "MPC885ADS"
+ select CPM1
help
Freescale Semiconductor MPC885 Application Development System (ADS).
Also known as DUET.
The MPC885ADS is meant to serve as a platform for s/w and h/w
development around the MPC885 processor family.
-config TQM823L
- bool "TQM823L"
- help
- Say Y here to support the TQM823L, one of an MPC8xx-based family of
- mini SBCs (half credit-card size) from TQ Components first released
- in late 1999. Technical references are at
- <http://www.denx.de/PDF/TQM8xxLHWM201.pdf>, and
- <http://www.denx.de/PDF/STK8xxLHWM201.pdf>, and an image at
- <http://www.denx.de/embedded-ppc-en.html>.
-
-config TQM850L
- bool "TQM850L"
- help
- Say Y here to support the TQM850L, one of an MPC8xx-based family of
- mini SBCs (half credit-card size) from TQ Components first released
- in late 1999. Technical references are at
- <http://www.denx.de/PDF/TQM8xxLHWM201.pdf>, and
- <http://www.denx.de/PDF/STK8xxLHWM201.pdf>, and an image at
- <http://www.denx.de/embedded-ppc-en.html>.
-
-config TQM855L
- bool "TQM855L"
- help
- Say Y here to support the TQM855L, one of an MPC8xx-based family of
- mini SBCs (half credit-card size) from TQ Components first released
- in late 1999. Technical references are at
- <http://www.denx.de/PDF/TQM8xxLHWM201.pdf>, and
- <http://www.denx.de/PDF/STK8xxLHWM201.pdf>, and an image at
- <http://www.denx.de/embedded-ppc-en.html>.
-
-config TQM860L
- bool "TQM860L"
- help
- Say Y here to support the TQM860L, one of an MPC8xx-based family of
- mini SBCs (half credit-card size) from TQ Components first released
- in late 1999. Technical references are at
- <http://www.denx.de/PDF/TQM8xxLHWM201.pdf>, and
- <http://www.denx.de/PDF/STK8xxLHWM201.pdf>, and an image at
- <http://www.denx.de/embedded-ppc-en.html>.
-
-config FPS850L
- bool "FPS850L"
-
-config IVMS8
- bool "IVMS8"
- help
- Say Y here to support the Integrated Voice-Mail Small 8-channel SBC
- from Speech Design, released March 2001. The manufacturer's website
- is at <http://www.speech-design.de/>.
-
-config IVML24
- bool "IVML24"
- help
- Say Y here to support the Integrated Voice-Mail Large 24-channel SBC
- from Speech Design, released March 2001. The manufacturer's website
- is at <http://www.speech-design.de/>.
-
-config HERMES_PRO
- bool "HERMES"
-
-config IP860
- bool "IP860"
-
-config LWMON
- bool "LWMON"
-
-config PCU_E
- bool "PCU_E"
-
-config CCM
- bool "CCM"
-
-config LANTEC
- bool "LANTEC"
+endchoice
-config MBX
- bool "MBX"
- help
- MBX is a line of Motorola single-board computer based around the
- MPC821 and MPC860 processors, and intended for embedded-controller
- applications. Say Y here to support these boards directly.
+menu "Freescale Ethernet driver platform-specific options"
+ depends on (FS_ENET && MPC885ADS)
+
+ config MPC8xx_SECOND_ETH
+ bool "Second Ethernet channel"
+ depends on MPC885ADS
+ default y
+ help
+ This enables support for second Ethernet on MPC885ADS and MPC86xADS boards.
+ The latter will use SCC1, for 885ADS you can select it below.
+
+ choice
+ prompt "Second Ethernet channel"
+ depends on MPC8xx_SECOND_ETH
+ default MPC8xx_SECOND_ETH_FEC2
+
+ config MPC8xx_SECOND_ETH_FEC2
+ bool "FEC2"
+ depends on MPC885ADS
+ help
+ Enable FEC2 to serve as 2-nd Ethernet channel. Note that SMC2
+ (often 2-nd UART) will not work if this is enabled.
+
+ config MPC8xx_SECOND_ETH_SCC3
+ bool "SCC3"
+ depends on MPC885ADS
+ help
+ Enable SCC3 to serve as 2-nd Ethernet channel. Note that SMC1
+ (often 1-nd UART) will not work if this is enabled.
+
+ endchoice
-config WINCEPT
- bool "WinCept"
- help
- The Wincept 100/110 is a Motorola single-board computer based on the
- MPC821 PowerPC, introduced in 1998 and designed to be used in
- thin-client machines. Say Y to support it directly.
+endmenu
-endchoice
+endmenu
#
# MPC8xx Communication options
menu "MPC8xx CPM Options"
depends on 8xx
-config SCC_ENET
- bool "CPM SCC Ethernet"
- depends on NET_ETHERNET
- help
- Enable Ethernet support via the Motorola MPC8xx serial
- communications controller.
-
-choice
- prompt "SCC used for Ethernet"
- depends on SCC_ENET
- default SCC1_ENET
-
-config SCC1_ENET
- bool "SCC1"
- help
- Use MPC8xx serial communications controller 1 to drive Ethernet
- (default).
-
-config SCC2_ENET
- bool "SCC2"
- help
- Use MPC8xx serial communications controller 2 to drive Ethernet.
-
-config SCC3_ENET
- bool "SCC3"
- help
- Use MPC8xx serial communications controller 3 to drive Ethernet.
-
-endchoice
-
-config FEC_ENET
- bool "860T FEC Ethernet"
- depends on NET_ETHERNET
- help
- Enable Ethernet support via the Fast Ethernet Controller (FCC) on
- the Motorola MPC8260.
-
-config USE_MDIO
- bool "Use MDIO for PHY configuration"
- depends on FEC_ENET
- help
- On some boards the hardware configuration of the ethernet PHY can be
- used without any software interaction over the MDIO interface, so
- all MII code can be omitted. Say N here if unsure or if you don't
- need link status reports.
-
-config FEC_AM79C874
- bool "Support AMD79C874 PHY"
- depends on USE_MDIO
-
-config FEC_LXT970
- bool "Support LXT970 PHY"
- depends on USE_MDIO
-
-config FEC_LXT971
- bool "Support LXT971 PHY"
- depends on USE_MDIO
-
-config FEC_QS6612
- bool "Support QS6612 PHY"
- depends on USE_MDIO
-
-config ENET_BIG_BUFFERS
- bool "Use Big CPM Ethernet Buffers"
- depends on SCC_ENET || FEC_ENET
- help
- Allocate large buffers for MPC8xx Ethernet. Increases throughput
- and decreases the likelihood of dropped packets, but costs memory.
-
-config HTDMSOUND
- bool "Embedded Planet HIOX Audio"
- depends on SOUND=y
-
# This doesn't really belong here, but it is convenient to ask
# 8xx specific questions.
comment "Generic MPC8xx Options"
--- /dev/null
+#
+# Makefile for the PowerPC 8xx linux kernel.
+#
+obj-$(CONFIG_PPC_8xx) += m8xx_setup.o
+obj-$(CONFIG_MPC885ADS) += mpc885ads_setup.o
--- /dev/null
+/*
+ * Copyright (C) 1995 Linus Torvalds
+ * Adapted from 'alpha' version by Gary Thomas
+ * Modified by Cort Dougan (cort@cs.nmt.edu)
+ * Modified for MBX using prep/chrp/pmac functions by Dan (dmalek@jlc.net)
+ * Further modified for generic 8xx by Dan.
+ */
+
+/*
+ * bootup setup stuff..
+ */
+
+#include <linux/errno.h>
+#include <linux/sched.h>
+#include <linux/kernel.h>
+#include <linux/mm.h>
+#include <linux/stddef.h>
+#include <linux/unistd.h>
+#include <linux/ptrace.h>
+#include <linux/slab.h>
+#include <linux/user.h>
+#include <linux/a.out.h>
+#include <linux/tty.h>
+#include <linux/major.h>
+#include <linux/interrupt.h>
+#include <linux/reboot.h>
+#include <linux/init.h>
+#include <linux/initrd.h>
+#include <linux/ioport.h>
+#include <linux/bootmem.h>
+#include <linux/seq_file.h>
+#include <linux/root_dev.h>
+#include <linux/time.h>
+#include <linux/rtc.h>
+
+#include <asm/mmu.h>
+#include <asm/reg.h>
+#include <asm/residual.h>
+#include <asm/io.h>
+#include <asm/pgtable.h>
+#include <asm/mpc8xx.h>
+#include <asm/8xx_immap.h>
+#include <asm/machdep.h>
+#include <asm/bootinfo.h>
+#include <asm/time.h>
+#include <asm/prom.h>
+#include <asm/fs_pd.h>
+#include <mm/mmu_decl.h>
+
+#include "sysdev/mpc8xx_pic.h"
+
+void m8xx_calibrate_decr(void);
+extern void m8xx_wdt_handler_install(bd_t *bp);
+extern int cpm_pic_init(void);
+extern int cpm_get_irq(void);
+
+/* A place holder for time base interrupts, if they are ever enabled. */
+irqreturn_t timebase_interrupt(int irq, void * dev)
+{
+ printk ("timebase_interrupt()\n");
+
+ return IRQ_HANDLED;
+}
+
+static struct irqaction tbint_irqaction = {
+ .handler = timebase_interrupt,
+ .mask = CPU_MASK_NONE,
+ .name = "tbint",
+};
+
+/* per-board overridable init_internal_rtc() function. */
+void __init __attribute__ ((weak))
+init_internal_rtc(void)
+{
+ sit8xx_t *sys_tmr = (sit8xx_t *) immr_map(im_sit);
+
+ /* Disable the RTC one second and alarm interrupts. */
+ clrbits16(&sys_tmr->sit_rtcsc, (RTCSC_SIE | RTCSC_ALE));
+
+ /* Enable the RTC */
+ setbits16(&sys_tmr->sit_rtcsc, (RTCSC_RTF | RTCSC_RTE));
+ immr_unmap(sys_tmr);
+}
+
+static int __init get_freq(char *name, unsigned long *val)
+{
+ struct device_node *cpu;
+ unsigned int *fp;
+ int found = 0;
+
+ /* The cpu node should have timebase and clock frequency properties */
+ cpu = of_find_node_by_type(NULL, "cpu");
+
+ if (cpu) {
+ fp = (unsigned int *)get_property(cpu, name, NULL);
+ if (fp) {
+ found = 1;
+ *val = *fp++;
+ }
+
+ of_node_put(cpu);
+ }
+
+ return found;
+}
+
+/* The decrementer counts at the system (internal) clock frequency divided by
+ * sixteen, or external oscillator divided by four. We force the processor
+ * to use system clock divided by sixteen.
+ */
+void __init mpc8xx_calibrate_decr(void)
+{
+ struct device_node *cpu;
+ cark8xx_t *clk_r1;
+ car8xx_t *clk_r2;
+ sitk8xx_t *sys_tmr1;
+ sit8xx_t *sys_tmr2;
+ int irq, virq;
+
+ clk_r1 = (cark8xx_t *) immr_map(im_clkrstk);
+
+ /* Unlock the SCCR. */
+ out_be32(&clk_r1->cark_sccrk, ~KAPWR_KEY);
+ out_be32(&clk_r1->cark_sccrk, KAPWR_KEY);
+ immr_unmap(clk_r1);
+
+ /* Force all 8xx processors to use divide by 16 processor clock. */
+ clk_r2 = (car8xx_t *) immr_map(im_clkrst);
+ setbits32(&clk_r2->car_sccr, 0x02000000);
+ immr_unmap(clk_r2);
+
+ /* Processor frequency is MHz.
+ */
+ ppc_tb_freq = 50000000;
+ if (!get_freq("bus-frequency", &ppc_tb_freq)) {
+ printk(KERN_ERR "WARNING: Estimating decrementer frequency "
+ "(not found)\n");
+ }
+ ppc_tb_freq /= 16;
+ ppc_proc_freq = 50000000;
+ if (!get_freq("clock-frequency", &ppc_proc_freq))
+ printk(KERN_ERR "WARNING: Estimating processor frequency"
+ "(not found)\n");
+
+ printk("Decrementer Frequency = 0x%lx\n", ppc_tb_freq);
+
+ /* Perform some more timer/timebase initialization. This used
+ * to be done elsewhere, but other changes caused it to get
+ * called more than once....that is a bad thing.
+ *
+ * First, unlock all of the registers we are going to modify.
+ * To protect them from corruption during power down, registers
+ * that are maintained by keep alive power are "locked". To
+ * modify these registers we have to write the key value to
+ * the key location associated with the register.
+ * Some boards power up with these unlocked, while others
+ * are locked. Writing anything (including the unlock code?)
+ * to the unlocked registers will lock them again. So, here
+ * we guarantee the registers are locked, then we unlock them
+ * for our use.
+ */
+ sys_tmr1 = (sitk8xx_t *) immr_map(im_sitk);
+ out_be32(&sys_tmr1->sitk_tbscrk, ~KAPWR_KEY);
+ out_be32(&sys_tmr1->sitk_rtcsck, ~KAPWR_KEY);
+ out_be32(&sys_tmr1->sitk_tbk, ~KAPWR_KEY);
+ out_be32(&sys_tmr1->sitk_tbscrk, KAPWR_KEY);
+ out_be32(&sys_tmr1->sitk_rtcsck, KAPWR_KEY);
+ out_be32(&sys_tmr1->sitk_tbk, KAPWR_KEY);
+ immr_unmap(sys_tmr1);
+
+ init_internal_rtc();
+
+ /* Enabling the decrementer also enables the timebase interrupts
+ * (or from the other point of view, to get decrementer interrupts
+ * we have to enable the timebase). The decrementer interrupt
+ * is wired into the vector table, nothing to do here for that.
+ */
+ cpu = of_find_node_by_type(NULL, "cpu");
+ virq= irq_of_parse_and_map(cpu, 0);
+ irq = irq_map[virq].hwirq;
+
+ sys_tmr2 = (sit8xx_t *) immr_map(im_sit);
+ out_be16(&sys_tmr2->sit_tbscr, ((1 << (7 - (irq/2))) << 8) |
+ (TBSCR_TBF | TBSCR_TBE));
+ immr_unmap(sys_tmr2);
+
+ if (setup_irq(virq, &tbint_irqaction))
+ panic("Could not allocate timer IRQ!");
+
+#ifdef CONFIG_8xx_WDT
+ /* Install watchdog timer handler early because it might be
+ * already enabled by the bootloader
+ */
+ m8xx_wdt_handler_install(binfo);
+#endif
+}
+
+/* The RTC on the MPC8xx is an internal register.
+ * We want to protect this during power down, so we need to unlock,
+ * modify, and re-lock.
+ */
+
+int mpc8xx_set_rtc_time(struct rtc_time *tm)
+{
+ sitk8xx_t *sys_tmr1;
+ sit8xx_t *sys_tmr2;
+ int time;
+
+ sys_tmr1 = (sitk8xx_t *) immr_map(im_sitk);
+ sys_tmr2 = (sit8xx_t *) immr_map(im_sit);
+ time = mktime(tm->tm_year+1900, tm->tm_mon+1, tm->tm_mday,
+ tm->tm_hour, tm->tm_min, tm->tm_sec);
+
+ out_be32(&sys_tmr1->sitk_rtck, KAPWR_KEY);
+ out_be32(&sys_tmr2->sit_rtc, time);
+ out_be32(&sys_tmr1->sitk_rtck, ~KAPWR_KEY);
+
+ immr_unmap(sys_tmr2);
+ immr_unmap(sys_tmr1);
+ return 0;
+}
+
+void mpc8xx_get_rtc_time(struct rtc_time *tm)
+{
+ unsigned long data;
+ sit8xx_t *sys_tmr = (sit8xx_t *) immr_map(im_sit);
+
+ /* Get time from the RTC. */
+ data = in_be32(&sys_tmr->sit_rtc);
+ to_tm(data, tm);
+ tm->tm_year -= 1900;
+ tm->tm_mon -= 1;
+ immr_unmap(sys_tmr);
+ return;
+}
+
+void mpc8xx_restart(char *cmd)
+{
+ __volatile__ unsigned char dummy;
+ car8xx_t * clk_r = (car8xx_t *) immr_map(im_clkrst);
+
+
+ local_irq_disable();
+
+ setbits32(&clk_r->car_plprcr, 0x00000080);
+ /* Clear the ME bit in MSR to cause checkstop on machine check
+ */
+ mtmsr(mfmsr() & ~0x1000);
+
+ dummy = in_8(&clk_r->res[0]);
+ printk("Restart failed\n");
+ while(1);
+}
+
+void mpc8xx_show_cpuinfo(struct seq_file *m)
+{
+ struct device_node *root;
+ uint memsize = total_memory;
+ const char *model = "";
+
+ seq_printf(m, "Vendor\t\t: Freescale Semiconductor\n");
+
+ root = of_find_node_by_path("/");
+ if (root)
+ model = get_property(root, "model", NULL);
+ seq_printf(m, "Machine\t\t: %s\n", model);
+ of_node_put(root);
+
+ seq_printf(m, "Memory\t\t: %d MB\n", memsize / (1024 * 1024));
+}
+
+static void cpm_cascade(unsigned int irq, struct irq_desc *desc)
+{
+ int cascade_irq;
+
+ if ((cascade_irq = cpm_get_irq()) >= 0) {
+ struct irq_desc *cdesc = irq_desc + cascade_irq;
+
+ generic_handle_irq(cascade_irq);
+ cdesc->chip->eoi(cascade_irq);
+ }
+ desc->chip->eoi(irq);
+}
+
+/* Initialize the internal interrupt controller. The number of
+ * interrupts supported can vary with the processor type, and the
+ * 82xx family can have up to 64.
+ * External interrupts can be either edge or level triggered, and
+ * need to be initialized by the appropriate driver.
+ */
+void __init m8xx_pic_init(void)
+{
+ int irq;
+
+ if (mpc8xx_pic_init()) {
+ printk(KERN_ERR "Failed interrupt 8xx controller initialization\n");
+ return;
+ }
+
+ irq = cpm_pic_init();
+ if (irq != NO_IRQ)
+ set_irq_chained_handler(irq, cpm_cascade);
+}
--- /dev/null
+/*
+ * A collection of structures, addresses, and values associated with
+ * the Freescale MPC885ADS board.
+ * Copied from the FADS stuff.
+ *
+ * Author: MontaVista Software, Inc.
+ * source@mvista.com
+ *
+ * 2005 (c) MontaVista Software, Inc. This file is licensed under the
+ * terms of the GNU General Public License version 2. This program is licensed
+ * "as is" without any warranty of any kind, whether express or implied.
+ */
+
+#ifdef __KERNEL__
+#ifndef __ASM_MPC885ADS_H__
+#define __ASM_MPC885ADS_H__
+
+#include <asm/ppcboot.h>
+#include <sysdev/fsl_soc.h>
+
+/* U-Boot maps BCSR to 0xff080000 */
+#define BCSR_ADDR ((uint)0xff080000)
+#define BCSR_SIZE ((uint)32)
+#define BCSR0 ((uint)(BCSR_ADDR + 0x00))
+#define BCSR1 ((uint)(BCSR_ADDR + 0x04))
+#define BCSR2 ((uint)(BCSR_ADDR + 0x08))
+#define BCSR3 ((uint)(BCSR_ADDR + 0x0c))
+#define BCSR4 ((uint)(BCSR_ADDR + 0x10))
+
+#define CFG_PHYDEV_ADDR ((uint)0xff0a0000)
+#define BCSR5 ((uint)(CFG_PHYDEV_ADDR + 0x300))
+
+#define IMAP_ADDR (get_immrbase())
+#define IMAP_SIZE ((uint)(64 * 1024))
+
+#define MPC8xx_CPM_OFFSET (0x9c0)
+#define CPM_MAP_ADDR (get_immrbase() + MPC8xx_CPM_OFFSET)
+#define CPM_IRQ_OFFSET 16 // for compability with cpm_uart driver
+
+#define PCMCIA_MEM_ADDR (uint)0xff020000)
+#define PCMCIA_MEM_SIZE ((uint)(64 * 1024))
+
+/* Bits of interest in the BCSRs.
+ */
+#define BCSR1_ETHEN ((uint)0x20000000)
+#define BCSR1_IRDAEN ((uint)0x10000000)
+#define BCSR1_RS232EN_1 ((uint)0x01000000)
+#define BCSR1_PCCEN ((uint)0x00800000)
+#define BCSR1_PCCVCC0 ((uint)0x00400000)
+#define BCSR1_PCCVPP0 ((uint)0x00200000)
+#define BCSR1_PCCVPP1 ((uint)0x00100000)
+#define BCSR1_PCCVPP_MASK (BCSR1_PCCVPP0 | BCSR1_PCCVPP1)
+#define BCSR1_RS232EN_2 ((uint)0x00040000)
+#define BCSR1_PCCVCC1 ((uint)0x00010000)
+#define BCSR1_PCCVCC_MASK (BCSR1_PCCVCC0 | BCSR1_PCCVCC1)
+
+#define BCSR4_ETH10_RST ((uint)0x80000000) /* 10Base-T PHY reset*/
+#define BCSR4_USB_LO_SPD ((uint)0x04000000)
+#define BCSR4_USB_VCC ((uint)0x02000000)
+#define BCSR4_USB_FULL_SPD ((uint)0x00040000)
+#define BCSR4_USB_EN ((uint)0x00020000)
+
+#define BCSR5_MII2_EN 0x40
+#define BCSR5_MII2_RST 0x20
+#define BCSR5_T1_RST 0x10
+#define BCSR5_ATM155_RST 0x08
+#define BCSR5_ATM25_RST 0x04
+#define BCSR5_MII1_EN 0x02
+#define BCSR5_MII1_RST 0x01
+
+/* Interrupt level assignments */
+#define PHY_INTERRUPT SIU_IRQ7 /* PHY link change interrupt */
+#define SIU_INT_FEC1 SIU_LEVEL1 /* FEC1 interrupt */
+#define SIU_INT_FEC2 SIU_LEVEL3 /* FEC2 interrupt */
+#define FEC_INTERRUPT SIU_INT_FEC1 /* FEC interrupt */
+
+/* We don't use the 8259 */
+#define NR_8259_INTS 0
+
+/* CPM Ethernet through SCC3 */
+#define PA_ENET_RXD ((ushort)0x0040)
+#define PA_ENET_TXD ((ushort)0x0080)
+#define PE_ENET_TCLK ((uint)0x00004000)
+#define PE_ENET_RCLK ((uint)0x00008000)
+#define PE_ENET_TENA ((uint)0x00000010)
+#define PC_ENET_CLSN ((ushort)0x0400)
+#define PC_ENET_RENA ((ushort)0x0800)
+
+/* Control bits in the SICR to route TCLK (CLK5) and RCLK (CLK6) to
+ * SCC3. Also, make sure GR3 (bit 8) and SC3 (bit 9) are zero */
+#define SICR_ENET_MASK ((uint)0x00ff0000)
+#define SICR_ENET_CLKRT ((uint)0x002c0000)
+
+#endif /* __ASM_MPC885ADS_H__ */
+#endif /* __KERNEL__ */
--- /dev/null
+/*arch/ppc/platforms/mpc885ads-setup.c
+ *
+ * Platform setup for the Freescale mpc885ads board
+ *
+ * Vitaly Bordug <vbordug@ru.mvista.com>
+ *
+ * Copyright 2005 MontaVista Software Inc.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/param.h>
+#include <linux/string.h>
+#include <linux/ioport.h>
+#include <linux/device.h>
+#include <linux/delay.h>
+#include <linux/root_dev.h>
+
+#include <linux/fs_enet_pd.h>
+#include <linux/fs_uart_pd.h>
+#include <linux/mii.h>
+
+#include <asm/delay.h>
+#include <asm/io.h>
+#include <asm/machdep.h>
+#include <asm/page.h>
+#include <asm/processor.h>
+#include <asm/system.h>
+#include <asm/time.h>
+#include <asm/ppcboot.h>
+#include <asm/mpc8xx.h>
+#include <asm/8xx_immap.h>
+#include <asm/commproc.h>
+#include <asm/fs_pd.h>
+#include <asm/prom.h>
+
+extern void cpm_reset(void);
+extern void mpc8xx_show_cpuinfo(struct seq_file*);
+extern void mpc8xx_restart(char *cmd);
+extern void mpc8xx_calibrate_decr(void);
+extern int mpc8xx_set_rtc_time(struct rtc_time *tm);
+extern void mpc8xx_get_rtc_time(struct rtc_time *tm);
+extern void m8xx_pic_init(void);
+extern unsigned int mpc8xx_get_irq(void);
+
+static void init_smc1_uart_ioports(struct fs_uart_platform_info* fpi);
+static void init_smc2_uart_ioports(struct fs_uart_platform_info* fpi);
+static void init_scc3_ioports(struct fs_platform_info* ptr);
+
+void __init mpc885ads_board_setup(void)
+{
+ cpm8xx_t *cp;
+ unsigned int *bcsr_io;
+ u8 tmpval8;
+
+#ifdef CONFIG_FS_ENET
+ iop8xx_t *io_port;
+#endif
+
+ bcsr_io = ioremap(BCSR1, sizeof(unsigned long));
+ cp = (cpm8xx_t *)immr_map(im_cpm);
+
+ if (bcsr_io == NULL) {
+ printk(KERN_CRIT "Could not remap BCSR\n");
+ return;
+ }
+#ifdef CONFIG_SERIAL_CPM_SMC1
+ clrbits32(bcsr_io, BCSR1_RS232EN_1);
+ clrbits32(&cp->cp_simode, 0xe0000000 >> 17); /* brg1 */
+ tmpval8 = in_8(&(cp->cp_smc[0].smc_smcm)) | (SMCM_RX | SMCM_TX);
+ out_8(&(cp->cp_smc[0].smc_smcm), tmpval8);
+ clrbits16(&cp->cp_smc[0].smc_smcmr, SMCMR_REN | SMCMR_TEN); /* brg1 */
+#else
+ setbits32(bcsr_io,BCSR1_RS232EN_1);
+ out_be16(&cp->cp_smc[0].smc_smcmr, 0);
+ out_8(&cp->cp_smc[0].smc_smce, 0);
+#endif
+
+#ifdef CONFIG_SERIAL_CPM_SMC2
+ clrbits32(bcsr_io,BCSR1_RS232EN_2);
+ clrbits32(&cp->cp_simode, 0xe0000000 >> 1);
+ setbits32(&cp->cp_simode, 0x20000000 >> 1); /* brg2 */
+ tmpval8 = in_8(&(cp->cp_smc[1].smc_smcm)) | (SMCM_RX | SMCM_TX);
+ out_8(&(cp->cp_smc[1].smc_smcm), tmpval8);
+ clrbits16(&cp->cp_smc[1].smc_smcmr, SMCMR_REN | SMCMR_TEN);
+
+ init_smc2_uart_ioports(0);
+#else
+ setbits32(bcsr_io,BCSR1_RS232EN_2);
+ out_be16(&cp->cp_smc[1].smc_smcmr, 0);
+ out_8(&cp->cp_smc[1].smc_smce, 0);
+#endif
+ immr_unmap(cp);
+ iounmap(bcsr_io);
+
+#ifdef CONFIG_FS_ENET
+ /* use MDC for MII (common) */
+ io_port = (iop8xx_t*)immr_map(im_ioport);
+ setbits16(&io_port->iop_pdpar, 0x0080);
+ clrbits16(&io_port->iop_pddir, 0x0080);
+
+ bcsr_io = ioremap(BCSR5, sizeof(unsigned long));
+ clrbits32(bcsr_io,BCSR5_MII1_EN);
+ clrbits32(bcsr_io,BCSR5_MII1_RST);
+#ifndef CONFIG_FC_ENET_HAS_SCC
+ clrbits32(bcsr_io,BCSR5_MII2_EN);
+ clrbits32(bcsr_io,BCSR5_MII2_RST);
+
+#endif
+ iounmap(bcsr_io);
+ immr_unmap(io_port);
+
+#endif
+}
+
+
+static void init_fec1_ioports(struct fs_platform_info* ptr)
+{
+ cpm8xx_t *cp = (cpm8xx_t *)immr_map(im_cpm);
+ iop8xx_t *io_port = (iop8xx_t *)immr_map(im_ioport);
+
+ /* configure FEC1 pins */
+ setbits16(&io_port->iop_papar, 0xf830);
+ setbits16(&io_port->iop_padir, 0x0830);
+ clrbits16(&io_port->iop_padir, 0xf000);
+
+ setbits32(&cp->cp_pbpar, 0x00001001);
+ clrbits32(&cp->cp_pbdir, 0x00001001);
+
+ setbits16(&io_port->iop_pcpar, 0x000c);
+ clrbits16(&io_port->iop_pcdir, 0x000c);
+
+ setbits32(&cp->cp_pepar, 0x00000003);
+ setbits32(&cp->cp_pedir, 0x00000003);
+ clrbits32(&cp->cp_peso, 0x00000003);
+ clrbits32(&cp->cp_cptr, 0x00000100);
+
+ immr_unmap(io_port);
+ immr_unmap(cp);
+}
+
+
+static void init_fec2_ioports(struct fs_platform_info* ptr)
+{
+ cpm8xx_t *cp = (cpm8xx_t *)immr_map(im_cpm);
+ iop8xx_t *io_port = (iop8xx_t *)immr_map(im_ioport);
+
+ /* configure FEC2 pins */
+ setbits32(&cp->cp_pepar, 0x0003fffc);
+ setbits32(&cp->cp_pedir, 0x0003fffc);
+ clrbits32(&cp->cp_peso, 0x000087fc);
+ setbits32(&cp->cp_peso, 0x00037800);
+ clrbits32(&cp->cp_cptr, 0x00000080);
+
+ immr_unmap(io_port);
+ immr_unmap(cp);
+}
+
+void init_fec_ioports(struct fs_platform_info *fpi)
+{
+ int fec_no = fs_get_fec_index(fpi->fs_no);
+
+ switch (fec_no) {
+ case 0:
+ init_fec1_ioports(fpi);
+ break;
+ case 1:
+ init_fec2_ioports(fpi);
+ break;
+ default:
+ printk(KERN_ERR "init_fec_ioports: invalid FEC number\n");
+ return;
+ }
+}
+
+static void init_scc3_ioports(struct fs_platform_info* fpi)
+{
+ unsigned *bcsr_io;
+ iop8xx_t *io_port;
+ cpm8xx_t *cp;
+
+ bcsr_io = ioremap(BCSR_ADDR, BCSR_SIZE);
+ io_port = (iop8xx_t *)immr_map(im_ioport);
+ cp = (cpm8xx_t *)immr_map(im_cpm);
+
+ if (bcsr_io == NULL) {
+ printk(KERN_CRIT "Could not remap BCSR\n");
+ return;
+ }
+
+ /* Enable the PHY.
+ */
+ clrbits32(bcsr_io+4, BCSR4_ETH10_RST);
+ udelay(1000);
+ setbits32(bcsr_io+4, BCSR4_ETH10_RST);
+ /* Configure port A pins for Txd and Rxd.
+ */
+ setbits16(&io_port->iop_papar, PA_ENET_RXD | PA_ENET_TXD);
+ clrbits16(&io_port->iop_padir, PA_ENET_RXD | PA_ENET_TXD);
+
+ /* Configure port C pins to enable CLSN and RENA.
+ */
+ clrbits16(&io_port->iop_pcpar, PC_ENET_CLSN | PC_ENET_RENA);
+ clrbits16(&io_port->iop_pcdir, PC_ENET_CLSN | PC_ENET_RENA);
+ setbits16(&io_port->iop_pcso, PC_ENET_CLSN | PC_ENET_RENA);
+
+ /* Configure port E for TCLK and RCLK.
+ */
+ setbits32(&cp->cp_pepar, PE_ENET_TCLK | PE_ENET_RCLK);
+ clrbits32(&cp->cp_pepar, PE_ENET_TENA);
+ clrbits32(&cp->cp_pedir,
+ PE_ENET_TCLK | PE_ENET_RCLK | PE_ENET_TENA);
+ clrbits32(&cp->cp_peso, PE_ENET_TCLK | PE_ENET_RCLK);
+ setbits32(&cp->cp_peso, PE_ENET_TENA);
+
+ /* Configure Serial Interface clock routing.
+ * First, clear all SCC bits to zero, then set the ones we want.
+ */
+ clrbits32(&cp->cp_sicr, SICR_ENET_MASK);
+ setbits32(&cp->cp_sicr, SICR_ENET_CLKRT);
+
+ /* Disable Rx and Tx. SMC1 sshould be stopped if SCC3 eternet are used.
+ */
+ clrbits16(&cp->cp_smc[0].smc_smcmr, SMCMR_REN | SMCMR_TEN);
+ /* On the MPC885ADS SCC ethernet PHY is initialized in the full duplex mode
+ * by H/W setting after reset. SCC ethernet controller support only half duplex.
+ * This discrepancy of modes causes a lot of carrier lost errors.
+ */
+
+ /* In the original SCC enet driver the following code is placed at
+ the end of the initialization */
+ setbits32(&cp->cp_pepar, PE_ENET_TENA);
+ clrbits32(&cp->cp_pedir, PE_ENET_TENA);
+ setbits32(&cp->cp_peso, PE_ENET_TENA);
+
+ setbits32(bcsr_io+4, BCSR1_ETHEN);
+ iounmap(bcsr_io);
+ immr_unmap(io_port);
+ immr_unmap(cp);
+}
+
+void init_scc_ioports(struct fs_platform_info *fpi)
+{
+ int scc_no = fs_get_scc_index(fpi->fs_no);
+
+ switch (scc_no) {
+ case 2:
+ init_scc3_ioports(fpi);
+ break;
+ default:
+ printk(KERN_ERR "init_scc_ioports: invalid SCC number\n");
+ return;
+ }
+}
+
+
+
+static void init_smc1_uart_ioports(struct fs_uart_platform_info* ptr)
+{
+ unsigned *bcsr_io;
+ cpm8xx_t *cp;
+
+ cp = (cpm8xx_t *)immr_map(im_cpm);
+ setbits32(&cp->cp_pepar, 0x000000c0);
+ clrbits32(&cp->cp_pedir, 0x000000c0);
+ clrbits32(&cp->cp_peso, 0x00000040);
+ setbits32(&cp->cp_peso, 0x00000080);
+ immr_unmap(cp);
+
+ bcsr_io = ioremap(BCSR1, sizeof(unsigned long));
+
+ if (bcsr_io == NULL) {
+ printk(KERN_CRIT "Could not remap BCSR1\n");
+ return;
+ }
+ clrbits32(bcsr_io,BCSR1_RS232EN_1);
+ iounmap(bcsr_io);
+}
+
+static void init_smc2_uart_ioports(struct fs_uart_platform_info* fpi)
+{
+ unsigned *bcsr_io;
+ cpm8xx_t *cp;
+
+ cp = (cpm8xx_t *)immr_map(im_cpm);
+ setbits32(&cp->cp_pepar, 0x00000c00);
+ clrbits32(&cp->cp_pedir, 0x00000c00);
+ clrbits32(&cp->cp_peso, 0x00000400);
+ setbits32(&cp->cp_peso, 0x00000800);
+ immr_unmap(cp);
+
+ bcsr_io = ioremap(BCSR1, sizeof(unsigned long));
+
+ if (bcsr_io == NULL) {
+ printk(KERN_CRIT "Could not remap BCSR1\n");
+ return;
+ }
+ clrbits32(bcsr_io,BCSR1_RS232EN_2);
+ iounmap(bcsr_io);
+}
+
+void init_smc_ioports(struct fs_uart_platform_info *data)
+{
+ int smc_no = fs_uart_id_fsid2smc(data->fs_no);
+
+ switch (smc_no) {
+ case 0:
+ init_smc1_uart_ioports(data);
+ data->brg = data->clk_rx;
+ break;
+ case 1:
+ init_smc2_uart_ioports(data);
+ data->brg = data->clk_rx;
+ break;
+ default:
+ printk(KERN_ERR "init_scc_ioports: invalid SCC number\n");
+ return;
+ }
+}
+
+int platform_device_skip(char *model, int id)
+{
+#ifdef CONFIG_MPC8xx_SECOND_ETH_SCC3
+ const char *dev = "FEC";
+ int n = 2;
+#else
+ const char *dev = "SCC";
+ int n = 3;
+#endif
+
+ if (!strcmp(model, dev) && n == id)
+ return 1;
+
+ return 0;
+}
+
+static void __init mpc885ads_setup_arch(void)
+{
+ struct device_node *cpu;
+
+ cpu = of_find_node_by_type(NULL, "cpu");
+ if (cpu != 0) {
+ const unsigned int *fp;
+
+ fp = get_property(cpu, "clock-frequency", NULL);
+ if (fp != 0)
+ loops_per_jiffy = *fp / HZ;
+ else
+ loops_per_jiffy = 50000000 / HZ;
+ of_node_put(cpu);
+ }
+
+ cpm_reset();
+
+ mpc885ads_board_setup();
+
+ ROOT_DEV = Root_NFS;
+}
+
+static int __init mpc885ads_probe(void)
+{
+ char *model = of_get_flat_dt_prop(of_get_flat_dt_root(),
+ "model", NULL);
+ if (model == NULL)
+ return 0;
+ if (strcmp(model, "MPC885ADS"))
+ return 0;
+
+ return 1;
+}
+
+define_machine(mpc885_ads) {
+ .name = "MPC885 ADS",
+ .probe = mpc885ads_probe,
+ .setup_arch = mpc885ads_setup_arch,
+ .init_IRQ = m8xx_pic_init,
+ .show_cpuinfo = mpc8xx_show_cpuinfo,
+ .get_irq = mpc8xx_get_irq,
+ .restart = mpc8xx_restart,
+ .calibrate_decr = mpc8xx_calibrate_decr,
+ .set_rtc_time = mpc8xx_set_rtc_time,
+ .get_rtc_time = mpc8xx_get_rtc_time,
+};
obj-$(CONFIG_PPC_MPC52xx) += 52xx/
obj-$(CONFIG_PPC_CHRP) += chrp/
obj-$(CONFIG_4xx) += 4xx/
+obj-$(CONFIG_PPC_8xx) += 8xx/
obj-$(CONFIG_PPC_83xx) += 83xx/
obj-$(CONFIG_PPC_85xx) += 85xx/
obj-$(CONFIG_PPC_86xx) += 86xx/
projects / linux-2.6 / commitdiff