#define E1000_WRITE_REG_IO(a, reg, val) \
e1000_write_reg_io((a), E1000_##reg, val)
-static int32_t e1000_configure_kmrn_for_10_100(struct e1000_hw *hw);
+static int32_t e1000_configure_kmrn_for_10_100(struct e1000_hw *hw,
+ uint16_t duplex);
static int32_t e1000_configure_kmrn_for_1000(struct e1000_hw *hw);
/* IGP cable length table */
hw->phy_type = e1000_phy_igp;
break;
}
+ case IGP03E1000_E_PHY_ID:
+ hw->phy_type = e1000_phy_igp_3;
+ break;
+ case IFE_E_PHY_ID:
+ case IFE_PLUS_E_PHY_ID:
+ case IFE_C_E_PHY_ID:
+ hw->phy_type = e1000_phy_ife;
+ break;
case GG82563_E_PHY_ID:
if (hw->mac_type == e1000_80003es2lan) {
hw->phy_type = e1000_phy_gg82563;
break;
case E1000_DEV_ID_82541EI:
case E1000_DEV_ID_82541EI_MOBILE:
+ case E1000_DEV_ID_82541ER_LOM:
hw->mac_type = e1000_82541;
break;
case E1000_DEV_ID_82541ER:
hw->mac_type = e1000_82541_rev_2;
break;
case E1000_DEV_ID_82547EI:
+ case E1000_DEV_ID_82547EI_MOBILE:
hw->mac_type = e1000_82547;
break;
case E1000_DEV_ID_82547GI:
case E1000_DEV_ID_82572EI_COPPER:
case E1000_DEV_ID_82572EI_FIBER:
case E1000_DEV_ID_82572EI_SERDES:
+ case E1000_DEV_ID_82572EI:
hw->mac_type = e1000_82572;
break;
case E1000_DEV_ID_82573E:
case E1000_DEV_ID_82573L:
hw->mac_type = e1000_82573;
break;
+ case E1000_DEV_ID_80003ES2LAN_COPPER_SPT:
+ case E1000_DEV_ID_80003ES2LAN_SERDES_SPT:
case E1000_DEV_ID_80003ES2LAN_COPPER_DPT:
case E1000_DEV_ID_80003ES2LAN_SERDES_DPT:
hw->mac_type = e1000_80003es2lan;
break;
+ case E1000_DEV_ID_ICH8_IGP_M_AMT:
+ case E1000_DEV_ID_ICH8_IGP_AMT:
+ case E1000_DEV_ID_ICH8_IGP_C:
+ case E1000_DEV_ID_ICH8_IFE:
+ case E1000_DEV_ID_ICH8_IGP_M:
+ hw->mac_type = e1000_ich8lan;
+ break;
default:
/* Should never have loaded on this device */
return -E1000_ERR_MAC_TYPE;
}
switch(hw->mac_type) {
+ case e1000_ich8lan:
+ hw->swfwhw_semaphore_present = TRUE;
+ hw->asf_firmware_present = TRUE;
+ break;
case e1000_80003es2lan:
hw->swfw_sync_present = TRUE;
/* fall through */
case e1000_82542_rev2_1:
hw->media_type = e1000_media_type_fiber;
break;
+ case e1000_ich8lan:
case e1000_82573:
/* The STATUS_TBIMODE bit is reserved or reused for the this
* device.
} while(timeout);
}
+ /* Workaround for ICH8 bit corruption issue in FIFO memory */
+ if (hw->mac_type == e1000_ich8lan) {
+ /* Set Tx and Rx buffer allocation to 8k apiece. */
+ E1000_WRITE_REG(hw, PBA, E1000_PBA_8K);
+ /* Set Packet Buffer Size to 16k. */
+ E1000_WRITE_REG(hw, PBS, E1000_PBS_16K);
+ }
+
/* Issue a global reset to the MAC. This will reset the chip's
* transmit, receive, DMA, and link units. It will not effect
* the current PCI configuration. The global reset bit is self-
/* Reset is performed on a shadow of the control register */
E1000_WRITE_REG(hw, CTRL_DUP, (ctrl | E1000_CTRL_RST));
break;
+ case e1000_ich8lan:
+ if (!hw->phy_reset_disable &&
+ e1000_check_phy_reset_block(hw) == E1000_SUCCESS) {
+ /* e1000_ich8lan PHY HW reset requires MAC CORE reset
+ * at the same time to make sure the interface between
+ * MAC and the external PHY is reset.
+ */
+ ctrl |= E1000_CTRL_PHY_RST;
+ }
+
+ e1000_get_software_flag(hw);
+ E1000_WRITE_REG(hw, CTRL, (ctrl | E1000_CTRL_RST));
+ msec_delay(5);
+ break;
default:
E1000_WRITE_REG(hw, CTRL, (ctrl | E1000_CTRL_RST));
break;
/* fall through */
case e1000_82571:
case e1000_82572:
+ case e1000_ich8lan:
case e1000_80003es2lan:
ret_val = e1000_get_auto_rd_done(hw);
if(ret_val)
e1000_pci_set_mwi(hw);
}
+ if (hw->mac_type == e1000_ich8lan) {
+ uint32_t kab = E1000_READ_REG(hw, KABGTXD);
+ kab |= E1000_KABGTXD_BGSQLBIAS;
+ E1000_WRITE_REG(hw, KABGTXD, kab);
+ }
+
return E1000_SUCCESS;
}
/* Disabling VLAN filtering. */
DEBUGOUT("Initializing the IEEE VLAN\n");
- if (hw->mac_type < e1000_82545_rev_3)
- E1000_WRITE_REG(hw, VET, 0);
- e1000_clear_vfta(hw);
+ /* VET hardcoded to standard value and VFTA removed in ICH8 LAN */
+ if (hw->mac_type != e1000_ich8lan) {
+ if (hw->mac_type < e1000_82545_rev_3)
+ E1000_WRITE_REG(hw, VET, 0);
+ e1000_clear_vfta(hw);
+ }
/* For 82542 (rev 2.0), disable MWI and put the receiver into reset */
if(hw->mac_type == e1000_82542_rev2_0) {
/* Zero out the Multicast HASH table */
DEBUGOUT("Zeroing the MTA\n");
mta_size = E1000_MC_TBL_SIZE;
+ if (hw->mac_type == e1000_ich8lan)
+ mta_size = E1000_MC_TBL_SIZE_ICH8LAN;
for(i = 0; i < mta_size; i++) {
E1000_WRITE_REG_ARRAY(hw, MTA, i, 0);
/* use write flush to prevent Memory Write Block (MWB) from
break;
}
+ /* More time needed for PHY to initialize */
+ if (hw->mac_type == e1000_ich8lan)
+ msec_delay(15);
+
/* Call a subroutine to configure the link and setup flow control. */
ret_val = e1000_setup_link(hw);
case e1000_82571:
case e1000_82572:
case e1000_82573:
+ case e1000_ich8lan:
case e1000_80003es2lan:
ctrl |= E1000_TXDCTL_COUNT_DESC;
break;
/* Fall through */
case e1000_82571:
case e1000_82572:
+ case e1000_ich8lan:
ctrl = E1000_READ_REG(hw, TXDCTL1);
ctrl = (ctrl & ~E1000_TXDCTL_WTHRESH) | E1000_TXDCTL_FULL_TX_DESC_WB;
if(hw->mac_type >= e1000_82571)
*/
e1000_clear_hw_cntrs(hw);
+ /* ICH8 No-snoop bits are opposite polarity.
+ * Set to snoop by default after reset. */
+ if (hw->mac_type == e1000_ich8lan)
+ e1000_set_pci_ex_no_snoop(hw, PCI_EX_82566_SNOOP_ALL);
+
if (hw->device_id == E1000_DEV_ID_82546GB_QUAD_COPPER ||
hw->device_id == E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3) {
ctrl_ext = E1000_READ_REG(hw, CTRL_EXT);
*/
if (hw->fc == e1000_fc_default) {
switch (hw->mac_type) {
+ case e1000_ich8lan:
case e1000_82573:
hw->fc = e1000_fc_full;
break;
*/
DEBUGOUT("Initializing the Flow Control address, type and timer regs\n");
- E1000_WRITE_REG(hw, FCAL, FLOW_CONTROL_ADDRESS_LOW);
- E1000_WRITE_REG(hw, FCAH, FLOW_CONTROL_ADDRESS_HIGH);
- E1000_WRITE_REG(hw, FCT, FLOW_CONTROL_TYPE);
+ /* FCAL/H and FCT are hardcoded to standard values in e1000_ich8lan. */
+ if (hw->mac_type != e1000_ich8lan) {
+ E1000_WRITE_REG(hw, FCT, FLOW_CONTROL_TYPE);
+ E1000_WRITE_REG(hw, FCAH, FLOW_CONTROL_ADDRESS_HIGH);
+ E1000_WRITE_REG(hw, FCAL, FLOW_CONTROL_ADDRESS_LOW);
+ }
E1000_WRITE_REG(hw, FCTTV, hw->fc_pause_time);
/* Wait 10ms for MAC to configure PHY from eeprom settings */
msec_delay(15);
-
+ if (hw->mac_type != e1000_ich8lan) {
/* Configure activity LED after PHY reset */
led_ctrl = E1000_READ_REG(hw, LEDCTL);
led_ctrl &= IGP_ACTIVITY_LED_MASK;
led_ctrl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE);
E1000_WRITE_REG(hw, LEDCTL, led_ctrl);
+ }
/* disable lplu d3 during driver init */
ret_val = e1000_set_d3_lplu_state(hw, FALSE);
if (ret_val)
return ret_val;
- /* Enable Pass False Carrier on the PHY */
- phy_data |= GG82563_KMCR_PASS_FALSE_CARRIER;
+ phy_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER;
ret_val = e1000_write_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL,
phy_data);
if(hw->autoneg_advertised == 0)
hw->autoneg_advertised = AUTONEG_ADVERTISE_SPEED_DEFAULT;
+ /* IFE phy only supports 10/100 */
+ if (hw->phy_type == e1000_phy_ife)
+ hw->autoneg_advertised &= AUTONEG_ADVERTISE_10_100_ALL;
+
DEBUGOUT("Reconfiguring auto-neg advertisement params\n");
ret_val = e1000_phy_setup_autoneg(hw);
if(ret_val) {
DEBUGFUNC("e1000_setup_copper_link");
+ switch (hw->mac_type) {
+ case e1000_80003es2lan:
+ case e1000_ich8lan:
+ /* Set the mac to wait the maximum time between each
+ * iteration and increase the max iterations when
+ * polling the phy; this fixes erroneous timeouts at 10Mbps. */
+ ret_val = e1000_write_kmrn_reg(hw, GG82563_REG(0x34, 4), 0xFFFF);
+ if (ret_val)
+ return ret_val;
+ ret_val = e1000_read_kmrn_reg(hw, GG82563_REG(0x34, 9), ®_data);
+ if (ret_val)
+ return ret_val;
+ reg_data |= 0x3F;
+ ret_val = e1000_write_kmrn_reg(hw, GG82563_REG(0x34, 9), reg_data);
+ if (ret_val)
+ return ret_val;
+ default:
+ break;
+ }
+
/* Check if it is a valid PHY and set PHY mode if necessary. */
ret_val = e1000_copper_link_preconfig(hw);
if(ret_val)
switch (hw->mac_type) {
case e1000_80003es2lan:
- ret_val = e1000_read_kmrn_reg(hw, E1000_KUMCTRLSTA_OFFSET_INB_CTRL,
- ®_data);
- if (ret_val)
- return ret_val;
+ /* Kumeran registers are written-only */
+ reg_data = E1000_KUMCTRLSTA_INB_CTRL_LINK_STATUS_TX_TIMEOUT_DEFAULT;
reg_data |= E1000_KUMCTRLSTA_INB_CTRL_DIS_PADDING;
ret_val = e1000_write_kmrn_reg(hw, E1000_KUMCTRLSTA_OFFSET_INB_CTRL,
reg_data);
}
if (hw->phy_type == e1000_phy_igp ||
+ hw->phy_type == e1000_phy_igp_3 ||
hw->phy_type == e1000_phy_igp_2) {
ret_val = e1000_copper_link_igp_setup(hw);
if(ret_val)
* hw - Struct containing variables accessed by shared code
******************************************************************************/
static int32_t
-e1000_configure_kmrn_for_10_100(struct e1000_hw *hw)
+e1000_configure_kmrn_for_10_100(struct e1000_hw *hw, uint16_t duplex)
{
int32_t ret_val = E1000_SUCCESS;
uint32_t tipg;
tipg |= DEFAULT_80003ES2LAN_TIPG_IPGT_10_100;
E1000_WRITE_REG(hw, TIPG, tipg);
+ ret_val = e1000_read_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, ®_data);
+
+ if (ret_val)
+ return ret_val;
+
+ if (duplex == HALF_DUPLEX)
+ reg_data |= GG82563_KMCR_PASS_FALSE_CARRIER;
+ else
+ reg_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER;
+
+ ret_val = e1000_write_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, reg_data);
+
return ret_val;
}
tipg |= DEFAULT_80003ES2LAN_TIPG_IPGT_1000;
E1000_WRITE_REG(hw, TIPG, tipg);
+ ret_val = e1000_read_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, ®_data);
+
+ if (ret_val)
+ return ret_val;
+
+ reg_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER;
+ ret_val = e1000_write_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, reg_data);
+
return ret_val;
}
if(ret_val)
return ret_val;
- /* Read the MII 1000Base-T Control Register (Address 9). */
- ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL, &mii_1000t_ctrl_reg);
- if(ret_val)
- return ret_val;
+ if (hw->phy_type != e1000_phy_ife) {
+ /* Read the MII 1000Base-T Control Register (Address 9). */
+ ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL, &mii_1000t_ctrl_reg);
+ if (ret_val)
+ return ret_val;
+ } else
+ mii_1000t_ctrl_reg=0;
/* Need to parse both autoneg_advertised and fc and set up
* the appropriate PHY registers. First we will parse for
if(hw->autoneg_advertised & ADVERTISE_1000_FULL) {
DEBUGOUT("Advertise 1000mb Full duplex\n");
mii_1000t_ctrl_reg |= CR_1000T_FD_CAPS;
+ if (hw->phy_type == e1000_phy_ife) {
+ DEBUGOUT("e1000_phy_ife is a 10/100 PHY. Gigabit speed is not supported.\n");
+ }
}
/* Check for a software override of the flow control settings, and
DEBUGOUT1("Auto-Neg Advertising %x\n", mii_autoneg_adv_reg);
- ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, mii_1000t_ctrl_reg);
- if(ret_val)
- return ret_val;
+ if (hw->phy_type != e1000_phy_ife) {
+ ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, mii_1000t_ctrl_reg);
+ if (ret_val)
+ return ret_val;
+ }
return E1000_SUCCESS;
}
/* Need to reset the PHY or these changes will be ignored */
mii_ctrl_reg |= MII_CR_RESET;
+ /* Disable MDI-X support for 10/100 */
+ } else if (hw->phy_type == e1000_phy_ife) {
+ ret_val = e1000_read_phy_reg(hw, IFE_PHY_MDIX_CONTROL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data &= ~IFE_PMC_AUTO_MDIX;
+ phy_data &= ~IFE_PMC_FORCE_MDIX;
+
+ ret_val = e1000_write_phy_reg(hw, IFE_PHY_MDIX_CONTROL, phy_data);
+ if (ret_val)
+ return ret_val;
} else {
/* Clear Auto-Crossover to force MDI manually. IGP requires MDI
* forced whenever speed or duplex are forced.
if (*speed == SPEED_1000)
ret_val = e1000_configure_kmrn_for_1000(hw);
else
- ret_val = e1000_configure_kmrn_for_10_100(hw);
+ ret_val = e1000_configure_kmrn_for_10_100(hw, *duplex);
+ if (ret_val)
+ return ret_val;
+ }
+
+ if ((hw->phy_type == e1000_phy_igp_3) && (*speed == SPEED_1000)) {
+ ret_val = e1000_kumeran_lock_loss_workaround(hw);
if (ret_val)
return ret_val;
}
DEBUGFUNC("e1000_swfw_sync_acquire");
+ if (hw->swfwhw_semaphore_present)
+ return e1000_get_software_flag(hw);
+
if (!hw->swfw_sync_present)
return e1000_get_hw_eeprom_semaphore(hw);
DEBUGFUNC("e1000_swfw_sync_release");
+ if (hw->swfwhw_semaphore_present) {
+ e1000_release_software_flag(hw);
+ return;
+ }
+
if (!hw->swfw_sync_present) {
e1000_put_hw_eeprom_semaphore(hw);
return;
if (e1000_swfw_sync_acquire(hw, swfw))
return -E1000_ERR_SWFW_SYNC;
- if((hw->phy_type == e1000_phy_igp ||
+ if ((hw->phy_type == e1000_phy_igp ||
+ hw->phy_type == e1000_phy_igp_3 ||
hw->phy_type == e1000_phy_igp_2) &&
(reg_addr > MAX_PHY_MULTI_PAGE_REG)) {
ret_val = e1000_write_phy_reg_ex(hw, IGP01E1000_PHY_PAGE_SELECT,
if (e1000_swfw_sync_acquire(hw, swfw))
return -E1000_ERR_SWFW_SYNC;
- if((hw->phy_type == e1000_phy_igp ||
+ if ((hw->phy_type == e1000_phy_igp ||
+ hw->phy_type == e1000_phy_igp_3 ||
hw->phy_type == e1000_phy_igp_2) &&
(reg_addr > MAX_PHY_MULTI_PAGE_REG)) {
ret_val = e1000_write_phy_reg_ex(hw, IGP01E1000_PHY_PAGE_SELECT,
E1000_WRITE_FLUSH(hw);
if (hw->mac_type >= e1000_82571)
- msec_delay(10);
+ msec_delay_irq(10);
e1000_swfw_sync_release(hw, swfw);
} else {
/* Read the Extended Device Control Register, assert the PHY_RESET_DIR
ret_val = e1000_get_phy_cfg_done(hw);
e1000_release_software_semaphore(hw);
+ if ((hw->mac_type == e1000_ich8lan) &&
+ (hw->phy_type == e1000_phy_igp_3)) {
+ ret_val = e1000_init_lcd_from_nvm(hw);
+ if (ret_val)
+ return ret_val;
+ }
return ret_val;
}
case e1000_82541_rev_2:
case e1000_82571:
case e1000_82572:
+ case e1000_ich8lan:
ret_val = e1000_phy_hw_reset(hw);
if(ret_val)
return ret_val;
+
break;
default:
ret_val = e1000_read_phy_reg(hw, PHY_CTRL, &phy_data);
/* The 82571 firmware may still be configuring the PHY. In this
* case, we cannot access the PHY until the configuration is done. So
* we explicitly set the PHY values. */
- if(hw->mac_type == e1000_82571 ||
- hw->mac_type == e1000_82572) {
+ if (hw->mac_type == e1000_82571 ||
+ hw->mac_type == e1000_82572) {
hw->phy_id = IGP01E1000_I_PHY_ID;
hw->phy_type = e1000_phy_igp_2;
return E1000_SUCCESS;
/* Read the PHY ID Registers to identify which PHY is onboard. */
ret_val = e1000_read_phy_reg(hw, PHY_ID1, &phy_id_high);
- if(ret_val)
+ if (ret_val)
return ret_val;
hw->phy_id = (uint32_t) (phy_id_high << 16);
case e1000_80003es2lan:
if (hw->phy_id == GG82563_E_PHY_ID) match = TRUE;
break;
+ case e1000_ich8lan:
+ if (hw->phy_id == IGP03E1000_E_PHY_ID) match = TRUE;
+ if (hw->phy_id == IFE_E_PHY_ID) match = TRUE;
+ if (hw->phy_id == IFE_PLUS_E_PHY_ID) match = TRUE;
+ if (hw->phy_id == IFE_C_E_PHY_ID) match = TRUE;
+ break;
default:
DEBUGOUT1("Invalid MAC type %d\n", hw->mac_type);
return -E1000_ERR_CONFIG;
return -E1000_ERR_CONFIG;
}
- if(hw->phy_type == e1000_phy_igp ||
+ if (hw->phy_type == e1000_phy_igp ||
+ hw->phy_type == e1000_phy_igp_3 ||
hw->phy_type == e1000_phy_igp_2)
return e1000_phy_igp_get_info(hw, phy_info);
+ else if (hw->phy_type == e1000_phy_ife)
+ return e1000_phy_ife_get_info(hw, phy_info);
else
return e1000_phy_m88_get_info(hw, phy_info);
}
eeprom->use_eerd = TRUE;
eeprom->use_eewr = FALSE;
break;
+ case e1000_ich8lan:
+ {
+ int32_t i = 0;
+ uint32_t flash_size = E1000_READ_ICH8_REG(hw, ICH8_FLASH_GFPREG);
+
+ eeprom->type = e1000_eeprom_ich8;
+ eeprom->use_eerd = FALSE;
+ eeprom->use_eewr = FALSE;
+ eeprom->word_size = E1000_SHADOW_RAM_WORDS;
+
+ /* Zero the shadow RAM structure. But don't load it from NVM
+ * so as to save time for driver init */
+ if (hw->eeprom_shadow_ram != NULL) {
+ for (i = 0; i < E1000_SHADOW_RAM_WORDS; i++) {
+ hw->eeprom_shadow_ram[i].modified = FALSE;
+ hw->eeprom_shadow_ram[i].eeprom_word = 0xFFFF;
+ }
+ }
+
+ hw->flash_base_addr = (flash_size & ICH8_GFPREG_BASE_MASK) *
+ ICH8_FLASH_SECTOR_SIZE;
+
+ hw->flash_bank_size = ((flash_size >> 16) & ICH8_GFPREG_BASE_MASK) + 1;
+ hw->flash_bank_size -= (flash_size & ICH8_GFPREG_BASE_MASK);
+ hw->flash_bank_size *= ICH8_FLASH_SECTOR_SIZE;
+ hw->flash_bank_size /= 2 * sizeof(uint16_t);
+
+ break;
+ }
default:
break;
}
return ret_val;
}
- if(eeprom->type == e1000_eeprom_spi) {
+ if (eeprom->type == e1000_eeprom_ich8)
+ return e1000_read_eeprom_ich8(hw, offset, words, data);
+
+ if (eeprom->type == e1000_eeprom_spi) {
uint16_t word_in;
uint8_t read_opcode = EEPROM_READ_OPCODE_SPI;
DEBUGFUNC("e1000_is_onboard_nvm_eeprom");
- if(hw->mac_type == e1000_82573) {
+ if (hw->mac_type == e1000_ich8lan)
+ return FALSE;
+
+ if (hw->mac_type == e1000_82573) {
eecd = E1000_READ_REG(hw, EECD);
/* Isolate bits 15 & 16 */
}
}
- for(i = 0; i < (EEPROM_CHECKSUM_REG + 1); i++) {
- if(e1000_read_eeprom(hw, i, 1, &eeprom_data) < 0) {
+ if (hw->mac_type == e1000_ich8lan) {
+ /* Drivers must allocate the shadow ram structure for the
+ * EEPROM checksum to be updated. Otherwise, this bit as well
+ * as the checksum must both be set correctly for this
+ * validation to pass.
+ */
+ e1000_read_eeprom(hw, 0x19, 1, &eeprom_data);
+ if ((eeprom_data & 0x40) == 0) {
+ eeprom_data |= 0x40;
+ e1000_write_eeprom(hw, 0x19, 1, &eeprom_data);
+ e1000_update_eeprom_checksum(hw);
+ }
+ }
+
+ for (i = 0; i < (EEPROM_CHECKSUM_REG + 1); i++) {
+ if (e1000_read_eeprom(hw, i, 1, &eeprom_data) < 0) {
DEBUGOUT("EEPROM Read Error\n");
return -E1000_ERR_EEPROM;
}
int32_t
e1000_update_eeprom_checksum(struct e1000_hw *hw)
{
+ uint32_t ctrl_ext;
uint16_t checksum = 0;
uint16_t i, eeprom_data;
return -E1000_ERR_EEPROM;
} else if (hw->eeprom.type == e1000_eeprom_flash) {
e1000_commit_shadow_ram(hw);
+ } else if (hw->eeprom.type == e1000_eeprom_ich8) {
+ e1000_commit_shadow_ram(hw);
+ /* Reload the EEPROM, or else modifications will not appear
+ * until after next adapter reset. */
+ ctrl_ext = E1000_READ_REG(hw, CTRL_EXT);
+ ctrl_ext |= E1000_CTRL_EXT_EE_RST;
+ E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext);
+ msec_delay(10);
}
return E1000_SUCCESS;
}
if(eeprom->use_eewr == TRUE)
return e1000_write_eeprom_eewr(hw, offset, words, data);
+ if (eeprom->type == e1000_eeprom_ich8)
+ return e1000_write_eeprom_ich8(hw, offset, words, data);
+
/* Prepare the EEPROM for writing */
if (e1000_acquire_eeprom(hw) != E1000_SUCCESS)
return -E1000_ERR_EEPROM;
uint32_t flop = 0;
uint32_t i = 0;
int32_t error = E1000_SUCCESS;
-
- /* The flop register will be used to determine if flash type is STM */
- flop = E1000_READ_REG(hw, FLOP);
+ uint32_t old_bank_offset = 0;
+ uint32_t new_bank_offset = 0;
+ uint32_t sector_retries = 0;
+ uint8_t low_byte = 0;
+ uint8_t high_byte = 0;
+ uint8_t temp_byte = 0;
+ boolean_t sector_write_failed = FALSE;
if (hw->mac_type == e1000_82573) {
+ /* The flop register will be used to determine if flash type is STM */
+ flop = E1000_READ_REG(hw, FLOP);
for (i=0; i < attempts; i++) {
eecd = E1000_READ_REG(hw, EECD);
if ((eecd & E1000_EECD_FLUPD) == 0) {
}
}
+ if (hw->mac_type == e1000_ich8lan && hw->eeprom_shadow_ram != NULL) {
+ /* We're writing to the opposite bank so if we're on bank 1,
+ * write to bank 0 etc. We also need to erase the segment that
+ * is going to be written */
+ if (!(E1000_READ_REG(hw, EECD) & E1000_EECD_SEC1VAL)) {
+ new_bank_offset = hw->flash_bank_size * 2;
+ old_bank_offset = 0;
+ e1000_erase_ich8_4k_segment(hw, 1);
+ } else {
+ old_bank_offset = hw->flash_bank_size * 2;
+ new_bank_offset = 0;
+ e1000_erase_ich8_4k_segment(hw, 0);
+ }
+
+ do {
+ sector_write_failed = FALSE;
+ /* Loop for every byte in the shadow RAM,
+ * which is in units of words. */
+ for (i = 0; i < E1000_SHADOW_RAM_WORDS; i++) {
+ /* Determine whether to write the value stored
+ * in the other NVM bank or a modified value stored
+ * in the shadow RAM */
+ if (hw->eeprom_shadow_ram[i].modified == TRUE) {
+ low_byte = (uint8_t)hw->eeprom_shadow_ram[i].eeprom_word;
+ e1000_read_ich8_byte(hw, (i << 1) + old_bank_offset,
+ &temp_byte);
+ udelay(100);
+ error = e1000_verify_write_ich8_byte(hw,
+ (i << 1) + new_bank_offset,
+ low_byte);
+ if (error != E1000_SUCCESS)
+ sector_write_failed = TRUE;
+ high_byte =
+ (uint8_t)(hw->eeprom_shadow_ram[i].eeprom_word >> 8);
+ e1000_read_ich8_byte(hw, (i << 1) + old_bank_offset + 1,
+ &temp_byte);
+ udelay(100);
+ } else {
+ e1000_read_ich8_byte(hw, (i << 1) + old_bank_offset,
+ &low_byte);
+ udelay(100);
+ error = e1000_verify_write_ich8_byte(hw,
+ (i << 1) + new_bank_offset, low_byte);
+ if (error != E1000_SUCCESS)
+ sector_write_failed = TRUE;
+ e1000_read_ich8_byte(hw, (i << 1) + old_bank_offset + 1,
+ &high_byte);
+ }
+
+ /* If the word is 0x13, then make sure the signature bits
+ * (15:14) are 11b until the commit has completed.
+ * This will allow us to write 10b which indicates the
+ * signature is valid. We want to do this after the write
+ * has completed so that we don't mark the segment valid
+ * while the write is still in progress */
+ if (i == E1000_ICH8_NVM_SIG_WORD)
+ high_byte = E1000_ICH8_NVM_SIG_MASK | high_byte;
+
+ error = e1000_verify_write_ich8_byte(hw,
+ (i << 1) + new_bank_offset + 1, high_byte);
+ if (error != E1000_SUCCESS)
+ sector_write_failed = TRUE;
+
+ if (sector_write_failed == FALSE) {
+ /* Clear the now not used entry in the cache */
+ hw->eeprom_shadow_ram[i].modified = FALSE;
+ hw->eeprom_shadow_ram[i].eeprom_word = 0xFFFF;
+ }
+ }
+
+ /* Don't bother writing the segment valid bits if sector
+ * programming failed. */
+ if (sector_write_failed == FALSE) {
+ /* Finally validate the new segment by setting bit 15:14
+ * to 10b in word 0x13 , this can be done without an
+ * erase as well since these bits are 11 to start with
+ * and we need to change bit 14 to 0b */
+ e1000_read_ich8_byte(hw,
+ E1000_ICH8_NVM_SIG_WORD * 2 + 1 + new_bank_offset,
+ &high_byte);
+ high_byte &= 0xBF;
+ error = e1000_verify_write_ich8_byte(hw,
+ E1000_ICH8_NVM_SIG_WORD * 2 + 1 + new_bank_offset,
+ high_byte);
+ if (error != E1000_SUCCESS)
+ sector_write_failed = TRUE;
+
+ /* And invalidate the previously valid segment by setting
+ * its signature word (0x13) high_byte to 0b. This can be
+ * done without an erase because flash erase sets all bits
+ * to 1's. We can write 1's to 0's without an erase */
+ error = e1000_verify_write_ich8_byte(hw,
+ E1000_ICH8_NVM_SIG_WORD * 2 + 1 + old_bank_offset,
+ 0);
+ if (error != E1000_SUCCESS)
+ sector_write_failed = TRUE;
+ }
+ } while (++sector_retries < 10 && sector_write_failed == TRUE);
+ }
+
return error;
}
* the other port. */
if ((hw->mac_type == e1000_82571) && (hw->laa_is_present == TRUE))
rar_num -= 1;
+ if (hw->mac_type == e1000_ich8lan)
+ rar_num = E1000_RAR_ENTRIES_ICH8LAN;
+
/* Zero out the other 15 receive addresses. */
DEBUGOUT("Clearing RAR[1-15]\n");
for(i = 1; i < rar_num; i++) {
}
}
-#if 0
/******************************************************************************
* Updates the MAC's list of multicast addresses.
*
/* Clear RAR[1-15] */
DEBUGOUT(" Clearing RAR[1-15]\n");
num_rar_entry = E1000_RAR_ENTRIES;
+ if (hw->mac_type == e1000_ich8lan)
+ num_rar_entry = E1000_RAR_ENTRIES_ICH8LAN;
/* Reserve a spot for the Locally Administered Address to work around
* an 82571 issue in which a reset on one port will reload the MAC on
* the other port. */
/* Clear the MTA */
DEBUGOUT(" Clearing MTA\n");
num_mta_entry = E1000_NUM_MTA_REGISTERS;
+ if (hw->mac_type == e1000_ich8lan)
+ num_mta_entry = E1000_NUM_MTA_REGISTERS_ICH8LAN;
for(i = 0; i < num_mta_entry; i++) {
E1000_WRITE_REG_ARRAY(hw, MTA, i, 0);
E1000_WRITE_FLUSH(hw);
}
DEBUGOUT("MC Update Complete\n");
}
-#endif /* 0 */
/******************************************************************************
* Hashes an address to determine its location in the multicast table
* LSB MSB
*/
case 0:
- /* [47:36] i.e. 0x563 for above example address */
- hash_value = ((mc_addr[4] >> 4) | (((uint16_t) mc_addr[5]) << 4));
+ if (hw->mac_type == e1000_ich8lan) {
+ /* [47:38] i.e. 0x158 for above example address */
+ hash_value = ((mc_addr[4] >> 6) | (((uint16_t) mc_addr[5]) << 2));
+ } else {
+ /* [47:36] i.e. 0x563 for above example address */
+ hash_value = ((mc_addr[4] >> 4) | (((uint16_t) mc_addr[5]) << 4));
+ }
break;
case 1:
- /* [46:35] i.e. 0xAC6 for above example address */
- hash_value = ((mc_addr[4] >> 3) | (((uint16_t) mc_addr[5]) << 5));
+ if (hw->mac_type == e1000_ich8lan) {
+ /* [46:37] i.e. 0x2B1 for above example address */
+ hash_value = ((mc_addr[4] >> 5) | (((uint16_t) mc_addr[5]) << 3));
+ } else {
+ /* [46:35] i.e. 0xAC6 for above example address */
+ hash_value = ((mc_addr[4] >> 3) | (((uint16_t) mc_addr[5]) << 5));
+ }
break;
case 2:
- /* [45:34] i.e. 0x5D8 for above example address */
- hash_value = ((mc_addr[4] >> 2) | (((uint16_t) mc_addr[5]) << 6));
+ if (hw->mac_type == e1000_ich8lan) {
+ /*[45:36] i.e. 0x163 for above example address */
+ hash_value = ((mc_addr[4] >> 4) | (((uint16_t) mc_addr[5]) << 4));
+ } else {
+ /* [45:34] i.e. 0x5D8 for above example address */
+ hash_value = ((mc_addr[4] >> 2) | (((uint16_t) mc_addr[5]) << 6));
+ }
break;
case 3:
- /* [43:32] i.e. 0x634 for above example address */
- hash_value = ((mc_addr[4]) | (((uint16_t) mc_addr[5]) << 8));
+ if (hw->mac_type == e1000_ich8lan) {
+ /* [43:34] i.e. 0x18D for above example address */
+ hash_value = ((mc_addr[4] >> 2) | (((uint16_t) mc_addr[5]) << 6));
+ } else {
+ /* [43:32] i.e. 0x634 for above example address */
+ hash_value = ((mc_addr[4]) | (((uint16_t) mc_addr[5]) << 8));
+ }
break;
}
hash_value &= 0xFFF;
+ if (hw->mac_type == e1000_ich8lan)
+ hash_value &= 0x3FF;
return hash_value;
}
* register are determined by the lower 5 bits of the value.
*/
hash_reg = (hash_value >> 5) & 0x7F;
+ if (hw->mac_type == e1000_ich8lan)
+ hash_reg &= 0x1F;
hash_bit = hash_value & 0x1F;
mta = E1000_READ_REG_ARRAY(hw, MTA, hash_reg);
{
uint32_t temp;
- if((hw->mac_type == e1000_82544) && ((offset & 0x1) == 1)) {
+ if (hw->mac_type == e1000_ich8lan)
+ return;
+
+ if ((hw->mac_type == e1000_82544) && ((offset & 0x1) == 1)) {
temp = E1000_READ_REG_ARRAY(hw, VFTA, (offset - 1));
E1000_WRITE_REG_ARRAY(hw, VFTA, offset, value);
E1000_WRITE_FLUSH(hw);
uint32_t vfta_offset = 0;
uint32_t vfta_bit_in_reg = 0;
+ if (hw->mac_type == e1000_ich8lan)
+ return;
+
if (hw->mac_type == e1000_82573) {
if (hw->mng_cookie.vlan_id != 0) {
/* The VFTA is a 4096b bit-field, each identifying a single VLAN
DEBUGOUT("EEPROM Read Error\n");
return -E1000_ERR_EEPROM;
}
- if((eeprom_data== ID_LED_RESERVED_0000) ||
- (eeprom_data == ID_LED_RESERVED_FFFF)) eeprom_data = ID_LED_DEFAULT;
- for(i = 0; i < 4; i++) {
+
+ if ((hw->mac_type == e1000_82573) &&
+ (eeprom_data == ID_LED_RESERVED_82573))
+ eeprom_data = ID_LED_DEFAULT_82573;
+ else if ((eeprom_data == ID_LED_RESERVED_0000) ||
+ (eeprom_data == ID_LED_RESERVED_FFFF)) {
+ if (hw->mac_type == e1000_ich8lan)
+ eeprom_data = ID_LED_DEFAULT_ICH8LAN;
+ else
+ eeprom_data = ID_LED_DEFAULT;
+ }
+ for (i = 0; i < 4; i++) {
temp = (eeprom_data >> (i << 2)) & led_mask;
switch(temp) {
case ID_LED_ON1_DEF2:
return ret_val;
/* Fall Through */
default:
+ if (hw->phy_type == e1000_phy_ife) {
+ e1000_write_phy_reg(hw, IFE_PHY_SPECIAL_CONTROL_LED, 0);
+ break;
+ }
/* Restore LEDCTL settings */
E1000_WRITE_REG(hw, LEDCTL, hw->ledctl_default);
break;
/* Clear SW Defineable Pin 0 to turn on the LED */
ctrl &= ~E1000_CTRL_SWDPIN0;
ctrl |= E1000_CTRL_SWDPIO0;
- } else if(hw->media_type == e1000_media_type_copper) {
+ } else if (hw->phy_type == e1000_phy_ife) {
+ e1000_write_phy_reg(hw, IFE_PHY_SPECIAL_CONTROL_LED,
+ (IFE_PSCL_PROBE_MODE | IFE_PSCL_PROBE_LEDS_ON));
+ } else if (hw->media_type == e1000_media_type_copper) {
E1000_WRITE_REG(hw, LEDCTL, hw->ledctl_mode2);
return E1000_SUCCESS;
}
/* Set SW Defineable Pin 0 to turn off the LED */
ctrl |= E1000_CTRL_SWDPIN0;
ctrl |= E1000_CTRL_SWDPIO0;
- } else if(hw->media_type == e1000_media_type_copper) {
+ } else if (hw->phy_type == e1000_phy_ife) {
+ e1000_write_phy_reg(hw, IFE_PHY_SPECIAL_CONTROL_LED,
+ (IFE_PSCL_PROBE_MODE | IFE_PSCL_PROBE_LEDS_OFF));
+ } else if (hw->media_type == e1000_media_type_copper) {
E1000_WRITE_REG(hw, LEDCTL, hw->ledctl_mode1);
return E1000_SUCCESS;
}
temp = E1000_READ_REG(hw, XOFFRXC);
temp = E1000_READ_REG(hw, XOFFTXC);
temp = E1000_READ_REG(hw, FCRUC);
+
+ if (hw->mac_type != e1000_ich8lan) {
temp = E1000_READ_REG(hw, PRC64);
temp = E1000_READ_REG(hw, PRC127);
temp = E1000_READ_REG(hw, PRC255);
temp = E1000_READ_REG(hw, PRC511);
temp = E1000_READ_REG(hw, PRC1023);
temp = E1000_READ_REG(hw, PRC1522);
+ }
+
temp = E1000_READ_REG(hw, GPRC);
temp = E1000_READ_REG(hw, BPRC);
temp = E1000_READ_REG(hw, MPRC);
temp = E1000_READ_REG(hw, TOTH);
temp = E1000_READ_REG(hw, TPR);
temp = E1000_READ_REG(hw, TPT);
+
+ if (hw->mac_type != e1000_ich8lan) {
temp = E1000_READ_REG(hw, PTC64);
temp = E1000_READ_REG(hw, PTC127);
temp = E1000_READ_REG(hw, PTC255);
temp = E1000_READ_REG(hw, PTC511);
temp = E1000_READ_REG(hw, PTC1023);
temp = E1000_READ_REG(hw, PTC1522);
+ }
+
temp = E1000_READ_REG(hw, MPTC);
temp = E1000_READ_REG(hw, BPTC);
temp = E1000_READ_REG(hw, IAC);
temp = E1000_READ_REG(hw, ICRXOC);
+
+ if (hw->mac_type == e1000_ich8lan) return;
+
temp = E1000_READ_REG(hw, ICRXPTC);
temp = E1000_READ_REG(hw, ICRXATC);
temp = E1000_READ_REG(hw, ICTXPTC);
hw->bus_width = e1000_bus_width_pciex_1;
break;
case e1000_82571:
+ case e1000_ich8lan:
case e1000_80003es2lan:
hw->bus_type = e1000_bus_type_pci_express;
hw->bus_speed = e1000_bus_speed_2500;
break;
}
}
-
-#if 0
/******************************************************************************
* Reads a value from one of the devices registers using port I/O (as opposed
* memory mapped I/O). Only 82544 and newer devices support port I/O.
e1000_io_write(hw, io_addr, offset);
return e1000_io_read(hw, io_data);
}
-#endif /* 0 */
/******************************************************************************
* Writes a value to one of the devices registers using port I/O (as opposed to
{
int32_t ret_val;
uint16_t agc_value = 0;
- uint16_t cur_agc, min_agc = IGP01E1000_AGC_LENGTH_TABLE_SIZE;
- uint16_t max_agc = 0;
uint16_t i, phy_data;
uint16_t cable_length;
break;
}
} else if(hw->phy_type == e1000_phy_igp) { /* For IGP PHY */
+ uint16_t cur_agc_value;
+ uint16_t min_agc_value = IGP01E1000_AGC_LENGTH_TABLE_SIZE;
uint16_t agc_reg_array[IGP01E1000_PHY_CHANNEL_NUM] =
{IGP01E1000_PHY_AGC_A,
IGP01E1000_PHY_AGC_B,
if(ret_val)
return ret_val;
- cur_agc = phy_data >> IGP01E1000_AGC_LENGTH_SHIFT;
+ cur_agc_value = phy_data >> IGP01E1000_AGC_LENGTH_SHIFT;
- /* Array bound check. */
- if((cur_agc >= IGP01E1000_AGC_LENGTH_TABLE_SIZE - 1) ||
- (cur_agc == 0))
+ /* Value bound check. */
+ if ((cur_agc_value >= IGP01E1000_AGC_LENGTH_TABLE_SIZE - 1) ||
+ (cur_agc_value == 0))
return -E1000_ERR_PHY;
- agc_value += cur_agc;
+ agc_value += cur_agc_value;
/* Update minimal AGC value. */
- if(min_agc > cur_agc)
- min_agc = cur_agc;
+ if (min_agc_value > cur_agc_value)
+ min_agc_value = cur_agc_value;
}
/* Remove the minimal AGC result for length < 50m */
- if(agc_value < IGP01E1000_PHY_CHANNEL_NUM * e1000_igp_cable_length_50) {
- agc_value -= min_agc;
+ if (agc_value < IGP01E1000_PHY_CHANNEL_NUM * e1000_igp_cable_length_50) {
+ agc_value -= min_agc_value;
/* Get the average length of the remaining 3 channels */
agc_value /= (IGP01E1000_PHY_CHANNEL_NUM - 1);
IGP01E1000_AGC_RANGE) : 0;
*max_length = e1000_igp_cable_length_table[agc_value] +
IGP01E1000_AGC_RANGE;
- } else if (hw->phy_type == e1000_phy_igp_2) {
+ } else if (hw->phy_type == e1000_phy_igp_2 ||
+ hw->phy_type == e1000_phy_igp_3) {
+ uint16_t cur_agc_index, max_agc_index = 0;
+ uint16_t min_agc_index = IGP02E1000_AGC_LENGTH_TABLE_SIZE - 1;
uint16_t agc_reg_array[IGP02E1000_PHY_CHANNEL_NUM] =
{IGP02E1000_PHY_AGC_A,
IGP02E1000_PHY_AGC_B,
/* Getting bits 15:9, which represent the combination of course and
* fine gain values. The result is a number that can be put into
* the lookup table to obtain the approximate cable length. */
- cur_agc = (phy_data >> IGP02E1000_AGC_LENGTH_SHIFT) &
- IGP02E1000_AGC_LENGTH_MASK;
+ cur_agc_index = (phy_data >> IGP02E1000_AGC_LENGTH_SHIFT) &
+ IGP02E1000_AGC_LENGTH_MASK;
+
+ /* Array index bound check. */
+ if ((cur_agc_index >= IGP02E1000_AGC_LENGTH_TABLE_SIZE) ||
+ (cur_agc_index == 0))
+ return -E1000_ERR_PHY;
/* Remove min & max AGC values from calculation. */
- if (e1000_igp_2_cable_length_table[min_agc] > e1000_igp_2_cable_length_table[cur_agc])
- min_agc = cur_agc;
- if (e1000_igp_2_cable_length_table[max_agc] < e1000_igp_2_cable_length_table[cur_agc])
- max_agc = cur_agc;
+ if (e1000_igp_2_cable_length_table[min_agc_index] >
+ e1000_igp_2_cable_length_table[cur_agc_index])
+ min_agc_index = cur_agc_index;
+ if (e1000_igp_2_cable_length_table[max_agc_index] <
+ e1000_igp_2_cable_length_table[cur_agc_index])
+ max_agc_index = cur_agc_index;
- agc_value += e1000_igp_2_cable_length_table[cur_agc];
+ agc_value += e1000_igp_2_cable_length_table[cur_agc_index];
}
- agc_value -= (e1000_igp_2_cable_length_table[min_agc] + e1000_igp_2_cable_length_table[max_agc]);
+ agc_value -= (e1000_igp_2_cable_length_table[min_agc_index] +
+ e1000_igp_2_cable_length_table[max_agc_index]);
agc_value /= (IGP02E1000_PHY_CHANNEL_NUM - 2);
/* Calculate cable length with the error range of +/- 10 meters. */
return ret_val;
*polarity = (phy_data & M88E1000_PSSR_REV_POLARITY) >>
M88E1000_PSSR_REV_POLARITY_SHIFT;
- } else if(hw->phy_type == e1000_phy_igp ||
+ } else if (hw->phy_type == e1000_phy_igp ||
+ hw->phy_type == e1000_phy_igp_3 ||
hw->phy_type == e1000_phy_igp_2) {
/* Read the Status register to check the speed */
ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_STATUS,
* 100 Mbps this bit is always 0) */
*polarity = phy_data & IGP01E1000_PSSR_POLARITY_REVERSED;
}
+ } else if (hw->phy_type == e1000_phy_ife) {
+ ret_val = e1000_read_phy_reg(hw, IFE_PHY_EXTENDED_STATUS_CONTROL,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+ *polarity = (phy_data & IFE_PESC_POLARITY_REVERSED) >>
+ IFE_PESC_POLARITY_REVERSED_SHIFT;
}
return E1000_SUCCESS;
}
DEBUGFUNC("e1000_check_downshift");
- if(hw->phy_type == e1000_phy_igp ||
+ if (hw->phy_type == e1000_phy_igp ||
+ hw->phy_type == e1000_phy_igp_3 ||
hw->phy_type == e1000_phy_igp_2) {
ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_LINK_HEALTH,
&phy_data);
hw->speed_downgraded = (phy_data & M88E1000_PSSR_DOWNSHIFT) >>
M88E1000_PSSR_DOWNSHIFT_SHIFT;
+ } else if (hw->phy_type == e1000_phy_ife) {
+ /* e1000_phy_ife supports 10/100 speed only */
+ hw->speed_downgraded = FALSE;
}
return E1000_SUCCESS;
if(speed == SPEED_1000) {
- e1000_get_cable_length(hw, &min_length, &max_length);
+ ret_val = e1000_get_cable_length(hw, &min_length, &max_length);
+ if (ret_val)
+ return ret_val;
if((hw->dsp_config_state == e1000_dsp_config_enabled) &&
min_length >= e1000_igp_cable_length_50) {
e1000_set_d3_lplu_state(struct e1000_hw *hw,
boolean_t active)
{
+ uint32_t phy_ctrl = 0;
int32_t ret_val;
uint16_t phy_data;
DEBUGFUNC("e1000_set_d3_lplu_state");
- if(hw->phy_type != e1000_phy_igp && hw->phy_type != e1000_phy_igp_2)
+ if (hw->phy_type != e1000_phy_igp && hw->phy_type != e1000_phy_igp_2
+ && hw->phy_type != e1000_phy_igp_3)
return E1000_SUCCESS;
/* During driver activity LPLU should not be used or it will attain link
* from the lowest speeds starting from 10Mbps. The capability is used for
* Dx transitions and states */
- if(hw->mac_type == e1000_82541_rev_2 || hw->mac_type == e1000_82547_rev_2) {
+ if (hw->mac_type == e1000_82541_rev_2 || hw->mac_type == e1000_82547_rev_2) {
ret_val = e1000_read_phy_reg(hw, IGP01E1000_GMII_FIFO, &phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
+ } else if (hw->mac_type == e1000_ich8lan) {
+ /* MAC writes into PHY register based on the state transition
+ * and start auto-negotiation. SW driver can overwrite the settings
+ * in CSR PHY power control E1000_PHY_CTRL register. */
+ phy_ctrl = E1000_READ_REG(hw, PHY_CTRL);
} else {
ret_val = e1000_read_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, &phy_data);
if(ret_val)
if(ret_val)
return ret_val;
} else {
+ if (hw->mac_type == e1000_ich8lan) {
+ phy_ctrl &= ~E1000_PHY_CTRL_NOND0A_LPLU;
+ E1000_WRITE_REG(hw, PHY_CTRL, phy_ctrl);
+ } else {
phy_data &= ~IGP02E1000_PM_D3_LPLU;
ret_val = e1000_write_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT,
phy_data);
if (ret_val)
return ret_val;
+ }
}
/* LPLU and SmartSpeed are mutually exclusive. LPLU is used during
(hw->autoneg_advertised == AUTONEG_ADVERTISE_10_100_ALL)) {
if(hw->mac_type == e1000_82541_rev_2 ||
- hw->mac_type == e1000_82547_rev_2) {
+ hw->mac_type == e1000_82547_rev_2) {
phy_data |= IGP01E1000_GMII_FLEX_SPD;
ret_val = e1000_write_phy_reg(hw, IGP01E1000_GMII_FIFO, phy_data);
if(ret_val)
return ret_val;
} else {
+ if (hw->mac_type == e1000_ich8lan) {
+ phy_ctrl |= E1000_PHY_CTRL_NOND0A_LPLU;
+ E1000_WRITE_REG(hw, PHY_CTRL, phy_ctrl);
+ } else {
phy_data |= IGP02E1000_PM_D3_LPLU;
ret_val = e1000_write_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT,
phy_data);
if (ret_val)
return ret_val;
+ }
}
/* When LPLU is enabled we should disable SmartSpeed */
e1000_set_d0_lplu_state(struct e1000_hw *hw,
boolean_t active)
{
+ uint32_t phy_ctrl = 0;
int32_t ret_val;
uint16_t phy_data;
DEBUGFUNC("e1000_set_d0_lplu_state");
if(hw->mac_type <= e1000_82547_rev_2)
return E1000_SUCCESS;
+ if (hw->mac_type == e1000_ich8lan) {
+ phy_ctrl = E1000_READ_REG(hw, PHY_CTRL);
+ } else {
ret_val = e1000_read_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, &phy_data);
if(ret_val)
return ret_val;
+ }
if (!active) {
+ if (hw->mac_type == e1000_ich8lan) {
+ phy_ctrl &= ~E1000_PHY_CTRL_D0A_LPLU;
+ E1000_WRITE_REG(hw, PHY_CTRL, phy_ctrl);
+ } else {
phy_data &= ~IGP02E1000_PM_D0_LPLU;
ret_val = e1000_write_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, phy_data);
if (ret_val)
return ret_val;
+ }
/* LPLU and SmartSpeed are mutually exclusive. LPLU is used during
* Dx states where the power conservation is most important. During
} else {
+ if (hw->mac_type == e1000_ich8lan) {
+ phy_ctrl |= E1000_PHY_CTRL_D0A_LPLU;
+ E1000_WRITE_REG(hw, PHY_CTRL, phy_ctrl);
+ } else {
phy_data |= IGP02E1000_PM_D0_LPLU;
ret_val = e1000_write_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, phy_data);
if (ret_val)
return ret_val;
+ }
/* When LPLU is enabled we should disable SmartSpeed */
ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, &phy_data);
* returns - TRUE when the mode is IAMT or FALSE.
****************************************************************************/
boolean_t
-e1000_check_mng_mode(
- struct e1000_hw *hw)
+e1000_check_mng_mode(struct e1000_hw *hw)
{
uint32_t fwsm;
fwsm = E1000_READ_REG(hw, FWSM);
- if((fwsm & E1000_FWSM_MODE_MASK) ==
- (E1000_MNG_IAMT_MODE << E1000_FWSM_MODE_SHIFT))
+ if (hw->mac_type == e1000_ich8lan) {
+ if ((fwsm & E1000_FWSM_MODE_MASK) ==
+ (E1000_MNG_ICH_IAMT_MODE << E1000_FWSM_MODE_SHIFT))
+ return TRUE;
+ } else if ((fwsm & E1000_FWSM_MODE_MASK) ==
+ (E1000_MNG_IAMT_MODE << E1000_FWSM_MODE_SHIFT))
return TRUE;
return FALSE;
E1000_WRITE_REG(hw, CTRL, ctrl);
}
-#if 0
/***************************************************************************
*
* Enables PCI-Express master access.
ctrl &= ~E1000_CTRL_GIO_MASTER_DISABLE;
E1000_WRITE_REG(hw, CTRL, ctrl);
}
-#endif /* 0 */
/*******************************************************************************
*
case e1000_82572:
case e1000_82573:
case e1000_80003es2lan:
- while(timeout) {
- if (E1000_READ_REG(hw, EECD) & E1000_EECD_AUTO_RD) break;
+ case e1000_ich8lan:
+ while (timeout) {
+ if (E1000_READ_REG(hw, EECD) & E1000_EECD_AUTO_RD)
+ break;
else msec_delay(1);
timeout--;
}
switch (hw->mac_type) {
default:
- msec_delay(10);
+ msec_delay_irq(10);
break;
case e1000_80003es2lan:
/* Separate *_CFG_DONE_* bit for each port */
e1000_check_phy_reset_block(struct e1000_hw *hw)
{
uint32_t manc = 0;
+ uint32_t fwsm = 0;
+
+ if (hw->mac_type == e1000_ich8lan) {
+ fwsm = E1000_READ_REG(hw, FWSM);
+ return (fwsm & E1000_FWSM_RSPCIPHY) ? E1000_SUCCESS
+ : E1000_BLK_PHY_RESET;
+ }
if (hw->mac_type > e1000_82547_rev_2)
manc = E1000_READ_REG(hw, MANC);
if((fwsm & E1000_FWSM_MODE_MASK) != 0)
return TRUE;
break;
+ case e1000_ich8lan:
+ return TRUE;
default:
break;
}
{
uint32_t ctrl_ext;
uint32_t swsm;
+ uint32_t extcnf;
/* Let firmware taken over control of h/w */
switch (adapter->hw.mac_type) {
swsm = E1000_READ_REG(&adapter->hw, SWSM);
E1000_WRITE_REG(&adapter->hw, SWSM,
swsm & ~E1000_SWSM_DRV_LOAD);
+ case e1000_ich8lan:
+ extcnf = E1000_READ_REG(&adapter->hw, CTRL_EXT);
+ E1000_WRITE_REG(&adapter->hw, CTRL_EXT,
+ extcnf & ~E1000_CTRL_EXT_DRV_LOAD);
+ break;
default:
break;
}
{
uint32_t ctrl_ext;
uint32_t swsm;
+ uint32_t extcnf;
/* Let firmware know the driver has taken over */
switch (adapter->hw.mac_type) {
case e1000_82571:
E1000_WRITE_REG(&adapter->hw, SWSM,
swsm | E1000_SWSM_DRV_LOAD);
break;
+ case e1000_ich8lan:
+ extcnf = E1000_READ_REG(&adapter->hw, EXTCNF_CTRL);
+ E1000_WRITE_REG(&adapter->hw, EXTCNF_CTRL,
+ extcnf | E1000_EXTCNF_CTRL_SWFLAG);
+ break;
default:
break;
}
* (b) AMT is active
* (c) SoL/IDER session is active */
if (!adapter->wol && adapter->hw.mac_type >= e1000_82540 &&
+ adapter->hw.mac_type != e1000_ich8lan &&
adapter->hw.media_type == e1000_media_type_copper &&
!(E1000_READ_REG(&adapter->hw, MANC) & E1000_MANC_SMBUS_EN) &&
!mng_mode_enabled &&
case e1000_82573:
pba = E1000_PBA_12K;
break;
+ case e1000_ich8lan:
+ pba = E1000_PBA_8K;
+ break;
default:
pba = E1000_PBA_48K;
break;
/* Set the FC high water mark to 90% of the FIFO size.
* Required to clear last 3 LSB */
fc_high_water_mark = ((pba * 9216)/10) & 0xFFF8;
+ /* We can't use 90% on small FIFOs because the remainder
+ * would be less than 1 full frame. In this case, we size
+ * it to allow at least a full frame above the high water
+ * mark. */
+ if (pba < E1000_PBA_16K)
+ fc_high_water_mark = (pba * 1024) - 1600;
adapter->hw.fc_high_water = fc_high_water_mark;
adapter->hw.fc_low_water = fc_high_water_mark - 8;
phy_data);
}
+ if (adapter->hw.mac_type < e1000_ich8lan)
+ /* FIXME: this code is duplicate and wrong for PCI Express */
if (adapter->en_mng_pt) {
manc = E1000_READ_REG(&adapter->hw, MANC);
manc |= (E1000_MANC_ARP_EN | E1000_MANC_EN_MNG2HOST);
struct net_device *netdev;
struct e1000_adapter *adapter;
unsigned long mmio_start, mmio_len;
+ unsigned long flash_start, flash_len;
static int cards_found = 0;
static int e1000_ksp3_port_a = 0; /* global ksp3 port a indication */
if ((err = pci_enable_device(pdev)))
return err;
- if (!(err = pci_set_dma_mask(pdev, DMA_64BIT_MASK))) {
+ if (!(err = pci_set_dma_mask(pdev, DMA_64BIT_MASK)) &&
+ !(err = pci_set_consistent_dma_mask(pdev, DMA_64BIT_MASK))) {
pci_using_dac = 1;
} else {
- if ((err = pci_set_dma_mask(pdev, DMA_32BIT_MASK))) {
+ if ((err = pci_set_dma_mask(pdev, DMA_32BIT_MASK)) &&
+ (err = pci_set_consistent_dma_mask(pdev, DMA_32BIT_MASK))) {
E1000_ERR("No usable DMA configuration, aborting\n");
return err;
}
if ((err = e1000_sw_init(adapter)))
goto err_sw_init;
+ /* Flash BAR mapping must happen after e1000_sw_init
+ * because it depends on mac_type */
+ if ((adapter->hw.mac_type == e1000_ich8lan) &&
+ (pci_resource_flags(pdev, 1) & IORESOURCE_MEM)) {
+ flash_start = pci_resource_start(pdev, 1);
+ flash_len = pci_resource_len(pdev, 1);
+ adapter->hw.flash_address = ioremap(flash_start, flash_len);
+ if (!adapter->hw.flash_address) {
+ err = -EIO;
+ goto err_flashmap;
+ }
+ }
+
if ((err = e1000_check_phy_reset_block(&adapter->hw)))
DPRINTK(PROBE, INFO, "PHY reset is blocked due to SOL/IDER session.\n");
NETIF_F_HW_VLAN_TX |
NETIF_F_HW_VLAN_RX |
NETIF_F_HW_VLAN_FILTER;
+ if (adapter->hw.mac_type == e1000_ich8lan)
+ netdev->features &= ~NETIF_F_HW_VLAN_FILTER;
}
#ifdef NETIF_F_TSO
if (pci_using_dac)
netdev->features |= NETIF_F_HIGHDMA;
- /* hard_start_xmit is safe against parallel locking */
netdev->features |= NETIF_F_LLTX;
adapter->en_mng_pt = e1000_enable_mng_pass_thru(&adapter->hw);
+ /* initialize eeprom parameters */
+
+ if (e1000_init_eeprom_params(&adapter->hw)) {
+ E1000_ERR("EEPROM initialization failed\n");
+ return -EIO;
+ }
+
/* before reading the EEPROM, reset the controller to
* put the device in a known good starting state */
EEPROM_INIT_CONTROL2_REG, 1, &eeprom_data);
eeprom_apme_mask = E1000_EEPROM_82544_APM;
break;
+ case e1000_ich8lan:
+ e1000_read_eeprom(&adapter->hw,
+ EEPROM_INIT_CONTROL1_REG, 1, &eeprom_data);
+ eeprom_apme_mask = E1000_EEPROM_ICH8_APME;
+ break;
case e1000_82546:
case e1000_82546_rev_3:
case e1000_82571:
return 0;
err_register:
+ if (adapter->hw.flash_address)
+ iounmap(adapter->hw.flash_address);
+err_flashmap:
err_sw_init:
err_eeprom:
iounmap(adapter->hw.hw_addr);
flush_scheduled_work();
if (adapter->hw.mac_type >= e1000_82540 &&
+ adapter->hw.mac_type != e1000_ich8lan &&
adapter->hw.media_type == e1000_media_type_copper) {
manc = E1000_READ_REG(&adapter->hw, MANC);
if (manc & E1000_MANC_SMBUS_EN) {
#endif
iounmap(adapter->hw.hw_addr);
+ if (adapter->hw.flash_address)
+ iounmap(adapter->hw.flash_address);
pci_release_regions(pdev);
free_netdev(netdev);
return -EIO;
}
- /* initialize eeprom parameters */
-
- if (e1000_init_eeprom_params(hw)) {
- E1000_ERR("EEPROM initialization failed\n");
- return -EIO;
- }
-
switch (hw->mac_type) {
default:
break;
int size;
size = sizeof(struct e1000_buffer) * txdr->count;
-
- txdr->buffer_info = vmalloc_node(size, pcibus_to_node(pdev->bus));
+ txdr->buffer_info = vmalloc(size);
if (!txdr->buffer_info) {
DPRINTK(PROBE, ERR,
"Unable to allocate memory for the transmit descriptor ring\n");
int size, desc_len;
size = sizeof(struct e1000_buffer) * rxdr->count;
- rxdr->buffer_info = vmalloc_node(size, pcibus_to_node(pdev->bus));
+ rxdr->buffer_info = vmalloc(size);
if (!rxdr->buffer_info) {
DPRINTK(PROBE, ERR,
"Unable to allocate memory for the receive descriptor ring\n");
uint32_t rctl;
uint32_t hash_value;
int i, rar_entries = E1000_RAR_ENTRIES;
+ int mta_reg_count = (hw->mac_type == e1000_ich8lan) ?
+ E1000_NUM_MTA_REGISTERS_ICH8LAN :
+ E1000_NUM_MTA_REGISTERS;
+
+ if (adapter->hw.mac_type == e1000_ich8lan)
+ rar_entries = E1000_RAR_ENTRIES_ICH8LAN;
/* reserve RAR[14] for LAA over-write work-around */
if (adapter->hw.mac_type == e1000_82571)
/* clear the old settings from the multicast hash table */
- for (i = 0; i < E1000_NUM_MTA_REGISTERS; i++) {
+ for (i = 0; i < mta_reg_count; i++) {
E1000_WRITE_REG_ARRAY(hw, MTA, i, 0);
E1000_WRITE_FLUSH(hw);
}
struct net_device *netdev = adapter->netdev;
struct e1000_tx_ring *txdr = adapter->tx_ring;
uint32_t link, tctl;
-
- e1000_check_for_link(&adapter->hw);
+ int32_t ret_val;
+
+ ret_val = e1000_check_for_link(&adapter->hw);
+ if ((ret_val == E1000_ERR_PHY) &&
+ (adapter->hw.phy_type == e1000_phy_igp_3) &&
+ (E1000_READ_REG(&adapter->hw, CTRL) & E1000_PHY_CTRL_GBE_DISABLE)) {
+ /* See e1000_kumeran_lock_loss_workaround() */
+ DPRINTK(LINK, INFO,
+ "Gigabit has been disabled, downgrading speed\n");
+ }
if (adapter->hw.mac_type == e1000_82573) {
e1000_enable_tx_pkt_filtering(&adapter->hw);
if (adapter->mng_vlan_id != adapter->hw.mng_cookie.vlan_id)
case e1000_82571:
case e1000_82572:
case e1000_82573:
+ case e1000_ich8lan:
pull_size = min((unsigned int)4, skb->data_len);
if (!__pskb_pull_tail(skb, pull_size)) {
DPRINTK(DRV, ERR,
/* Adapter-specific max frame size limits. */
switch (adapter->hw.mac_type) {
case e1000_undefined ... e1000_82542_rev2_1:
+ case e1000_ich8lan:
if (max_frame > MAXIMUM_ETHERNET_FRAME_SIZE) {
DPRINTK(PROBE, ERR, "Jumbo Frames not supported.\n");
return -EINVAL;
adapter->stats.bprc += E1000_READ_REG(hw, BPRC);
adapter->stats.mprc += E1000_READ_REG(hw, MPRC);
adapter->stats.roc += E1000_READ_REG(hw, ROC);
+
+ if (adapter->hw.mac_type != e1000_ich8lan) {
adapter->stats.prc64 += E1000_READ_REG(hw, PRC64);
adapter->stats.prc127 += E1000_READ_REG(hw, PRC127);
adapter->stats.prc255 += E1000_READ_REG(hw, PRC255);
adapter->stats.prc511 += E1000_READ_REG(hw, PRC511);
adapter->stats.prc1023 += E1000_READ_REG(hw, PRC1023);
adapter->stats.prc1522 += E1000_READ_REG(hw, PRC1522);
+ }
adapter->stats.symerrs += E1000_READ_REG(hw, SYMERRS);
adapter->stats.mpc += E1000_READ_REG(hw, MPC);
adapter->stats.totl += E1000_READ_REG(hw, TOTL);
adapter->stats.toth += E1000_READ_REG(hw, TOTH);
adapter->stats.tpr += E1000_READ_REG(hw, TPR);
+
+ if (adapter->hw.mac_type != e1000_ich8lan) {
adapter->stats.ptc64 += E1000_READ_REG(hw, PTC64);
adapter->stats.ptc127 += E1000_READ_REG(hw, PTC127);
adapter->stats.ptc255 += E1000_READ_REG(hw, PTC255);
adapter->stats.ptc511 += E1000_READ_REG(hw, PTC511);
adapter->stats.ptc1023 += E1000_READ_REG(hw, PTC1023);
adapter->stats.ptc1522 += E1000_READ_REG(hw, PTC1522);
+ }
+
adapter->stats.mptc += E1000_READ_REG(hw, MPTC);
adapter->stats.bptc += E1000_READ_REG(hw, BPTC);
if (hw->mac_type > e1000_82547_rev_2) {
adapter->stats.iac += E1000_READ_REG(hw, IAC);
adapter->stats.icrxoc += E1000_READ_REG(hw, ICRXOC);
+
+ if (adapter->hw.mac_type != e1000_ich8lan) {
adapter->stats.icrxptc += E1000_READ_REG(hw, ICRXPTC);
adapter->stats.icrxatc += E1000_READ_REG(hw, ICRXATC);
adapter->stats.ictxptc += E1000_READ_REG(hw, ICTXPTC);
adapter->stats.ictxqec += E1000_READ_REG(hw, ICTXQEC);
adapter->stats.ictxqmtc += E1000_READ_REG(hw, ICTXQMTC);
adapter->stats.icrxdmtc += E1000_READ_REG(hw, ICRXDMTC);
+ }
}
/* Fill out the OS statistics structure */
ctrl |= E1000_CTRL_VME;
E1000_WRITE_REG(&adapter->hw, CTRL, ctrl);
+ if (adapter->hw.mac_type != e1000_ich8lan) {
/* enable VLAN receive filtering */
rctl = E1000_READ_REG(&adapter->hw, RCTL);
rctl |= E1000_RCTL_VFE;
rctl &= ~E1000_RCTL_CFIEN;
E1000_WRITE_REG(&adapter->hw, RCTL, rctl);
e1000_update_mng_vlan(adapter);
+ }
} else {
/* disable VLAN tag insert/strip */
ctrl = E1000_READ_REG(&adapter->hw, CTRL);
ctrl &= ~E1000_CTRL_VME;
E1000_WRITE_REG(&adapter->hw, CTRL, ctrl);
+ if (adapter->hw.mac_type != e1000_ich8lan) {
/* disable VLAN filtering */
rctl = E1000_READ_REG(&adapter->hw, RCTL);
rctl &= ~E1000_RCTL_VFE;
e1000_vlan_rx_kill_vid(netdev, adapter->mng_vlan_id);
adapter->mng_vlan_id = E1000_MNG_VLAN_NONE;
}
+ }
}
e1000_irq_enable(adapter);
pci_enable_wake(pdev, PCI_D3cold, 0);
}
+ /* FIXME: this code is incorrect for PCI Express */
if (adapter->hw.mac_type >= e1000_82540 &&
+ adapter->hw.mac_type != e1000_ich8lan &&
adapter->hw.media_type == e1000_media_type_copper) {
manc = E1000_READ_REG(&adapter->hw, MANC);
if (manc & E1000_MANC_SMBUS_EN) {
}
}
+ if (adapter->hw.phy_type == e1000_phy_igp_3)
+ e1000_phy_powerdown_workaround(&adapter->hw);
+
/* Release control of h/w to f/w. If f/w is AMT enabled, this
* would have already happened in close and is redundant. */
e1000_release_hw_control(adapter);
netif_device_attach(netdev);
+ /* FIXME: this code is incorrect for PCI Express */
if (adapter->hw.mac_type >= e1000_82540 &&
+ adapter->hw.mac_type != e1000_ich8lan &&
adapter->hw.media_type == e1000_media_type_copper) {
manc = E1000_READ_REG(&adapter->hw, MANC);
manc &= ~(E1000_MANC_ARP_EN);
projects / linux-2.6 / commitdiff