--- /dev/null
+/*
+ * mpc7448_hpc2.c
+ *
+ * Board setup routines for the Freescale Taiga platform
+ *
+ * Author: Jacob Pan
+ * jacob.pan@freescale.com
+ * Author: Xianghua Xiao
+ * x.xiao@freescale.com
+ * Maintainer: Roy Zang <tie-fei.zang@freescale.com>
+ * Add Flat Device Tree support fot mpc7448hpc2 board
+ *
+ * Copyright 2004-2006 Freescale Semiconductor, Inc.
+ *
+ * This file is licensed under
+ * the terms of the GNU General Public License version 2. This program
+ * is licensed "as is" without any warranty of any kind, whether express
+ * or implied.
+ */
+
+#include <linux/config.h>
+#include <linux/stddef.h>
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <linux/kdev_t.h>
+#include <linux/console.h>
+#include <linux/delay.h>
+#include <linux/irq.h>
+#include <linux/ide.h>
+#include <linux/seq_file.h>
+#include <linux/root_dev.h>
+#include <linux/serial.h>
+#include <linux/tty.h>
+#include <linux/serial_core.h>
+
+#include <asm/system.h>
+#include <asm/time.h>
+#include <asm/machdep.h>
+#include <asm/prom.h>
+#include <asm/udbg.h>
+#include <asm/tsi108.h>
+#include <asm/pci-bridge.h>
+#include <asm/reg.h>
+#include <mm/mmu_decl.h>
+#include "mpc7448_hpc2.h"
+#include <asm/tsi108_irq.h>
+#include <asm/mpic.h>
+
+#undef DEBUG
+#ifdef DEBUG
+#define DBG(fmt...) do { printk(fmt); } while(0)
+#else
+#define DBG(fmt...) do { } while(0)
+#endif
+
+#ifndef CONFIG_PCI
+isa_io_base = MPC7448_HPC2_ISA_IO_BASE;
+isa_mem_base = MPC7448_HPC2_ISA_MEM_BASE;
+pci_dram_offset = MPC7448_HPC2_PCI_MEM_OFFSET;
+#endif
+
+extern int tsi108_setup_pci(struct device_node *dev);
+extern void _nmask_and_or_msr(unsigned long nmask, unsigned long or_val);
+extern void tsi108_pci_int_init(void);
+extern int tsi108_irq_cascade(struct pt_regs *regs, void *unused);
+
+/*
+ * Define all of the IRQ senses and polarities. Taken from the
+ * mpc7448hpc manual.
+ * Note: Likely, this table and the following function should be
+ * obtained and derived from the OF Device Tree.
+ */
+
+static u_char mpc7448_hpc2_pic_initsenses[] __initdata = {
+ /* External on-board sources */
+ (IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE), /* INT[0] XINT0 from FPGA */
+ (IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE), /* INT[1] XINT1 from FPGA */
+ (IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE), /* INT[2] PHY_INT from both GIGE */
+ (IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE), /* INT[3] RESERVED */
+ /* Internal Tsi108/109 interrupt sources */
+ (IRQ_SENSE_EDGE | IRQ_POLARITY_POSITIVE), /* Reserved IRQ */
+ (IRQ_SENSE_EDGE | IRQ_POLARITY_POSITIVE), /* Reserved IRQ */
+ (IRQ_SENSE_EDGE | IRQ_POLARITY_POSITIVE), /* Reserved IRQ */
+ (IRQ_SENSE_EDGE | IRQ_POLARITY_POSITIVE), /* Reserved IRQ */
+ (IRQ_SENSE_EDGE | IRQ_POLARITY_POSITIVE), /* DMA0 */
+ (IRQ_SENSE_EDGE | IRQ_POLARITY_POSITIVE), /* DMA1 */
+ (IRQ_SENSE_EDGE | IRQ_POLARITY_POSITIVE), /* DMA2 */
+ (IRQ_SENSE_EDGE | IRQ_POLARITY_POSITIVE), /* DMA3 */
+ (IRQ_SENSE_EDGE | IRQ_POLARITY_POSITIVE), /* UART0 */
+ (IRQ_SENSE_EDGE | IRQ_POLARITY_POSITIVE), /* UART1 */
+ (IRQ_SENSE_EDGE | IRQ_POLARITY_POSITIVE), /* I2C */
+ (IRQ_SENSE_EDGE | IRQ_POLARITY_POSITIVE), /* GPIO */
+ (IRQ_SENSE_LEVEL | IRQ_POLARITY_POSITIVE), /* GIGE0 */
+ (IRQ_SENSE_LEVEL | IRQ_POLARITY_POSITIVE), /* GIGE1 */
+ (IRQ_SENSE_EDGE | IRQ_POLARITY_POSITIVE), /* Reserved IRQ */
+ (IRQ_SENSE_EDGE | IRQ_POLARITY_POSITIVE), /* HLP */
+ (IRQ_SENSE_EDGE | IRQ_POLARITY_POSITIVE), /* SDC */
+ (IRQ_SENSE_EDGE | IRQ_POLARITY_POSITIVE), /* Processor IF */
+ (IRQ_SENSE_EDGE | IRQ_POLARITY_POSITIVE), /* Reserved IRQ */
+ (IRQ_SENSE_LEVEL | IRQ_POLARITY_POSITIVE), /* PCI/X block */
+};
+
+int mpc7448_hpc2_exclude_device(u_char bus, u_char devfn)
+{
+ if (bus == 0 && PCI_SLOT(devfn) == 0)
+ return PCIBIOS_DEVICE_NOT_FOUND;
+ else
+ return PCIBIOS_SUCCESSFUL;
+}
+
+/*
+ * find pci slot by devfn in interrupt map of OF tree
+ */
+u8 find_slot_by_devfn(unsigned int *interrupt_map, unsigned int devfn)
+{
+ int i;
+ unsigned int tmp;
+ for (i = 0; i < 4; i++){
+ tmp = interrupt_map[i*4*7];
+ if ((tmp >> 11) == (devfn >> 3))
+ return i;
+ }
+ return i;
+}
+
+/*
+ * Scans the interrupt map for pci device
+ */
+void mpc7448_hpc2_fixup_irq(struct pci_dev *dev)
+{
+ struct pci_controller *hose;
+ struct device_node *node;
+ unsigned int *interrupt;
+ int busnr;
+ int len;
+ u8 slot;
+ u8 pin;
+
+ /* Lookup the hose */
+ busnr = dev->bus->number;
+ hose = pci_bus_to_hose(busnr);
+ if (!hose)
+ printk(KERN_ERR "No pci hose found\n");
+
+ /* Check it has an OF node associated */
+ node = (struct device_node *) hose->arch_data;
+ if (!node)
+ printk(KERN_ERR "No pci node found\n");
+
+ interrupt = (unsigned int *) get_property(node, "interrupt-map", &len);
+ slot = find_slot_by_devfn(interrupt, dev->devfn);
+ pci_read_config_byte(dev, PCI_INTERRUPT_PIN, &pin);
+ if (pin == 0 || pin > 4)
+ pin = 1;
+ pin--;
+ dev->irq = interrupt[slot*4*7 + pin*7 + 5];
+ DBG("TSI_PCI: dev->irq = 0x%x\n", dev->irq);
+}
+/* temporary pci irq map fixup*/
+
+void __init mpc7448_hpc2_pcibios_fixup(void)
+{
+ struct pci_dev *dev = NULL;
+ for_each_pci_dev(dev) {
+ mpc7448_hpc2_fixup_irq(dev);
+ pci_write_config_byte(dev, PCI_INTERRUPT_LINE, dev->irq);
+ }
+}
+
+static void __init mpc7448_hpc2_setup_arch(void)
+{
+ struct device_node *cpu;
+ struct device_node *np;
+ if (ppc_md.progress)
+ ppc_md.progress("mpc7448_hpc2_setup_arch():set_bridge", 0);
+
+ cpu = of_find_node_by_type(NULL, "cpu");
+ if (cpu != 0) {
+ unsigned int *fp;
+
+ fp = (int *)get_property(cpu, "clock-frequency", NULL);
+ if (fp != 0)
+ loops_per_jiffy = *fp / HZ;
+ else
+ loops_per_jiffy = 50000000 / HZ;
+ of_node_put(cpu);
+ }
+ tsi108_csr_vir_base = get_vir_csrbase();
+
+#ifdef CONFIG_ROOT_NFS
+ ROOT_DEV = Root_NFS;
+#else
+ ROOT_DEV = Root_HDA1;
+#endif
+
+#ifdef CONFIG_BLK_DEV_INITRD
+ ROOT_DEV = Root_RAM0;
+#endif
+
+ /* setup PCI host bridge */
+#ifdef CONFIG_PCI
+ for (np = NULL; (np = of_find_node_by_type(np, "pci")) != NULL;)
+ tsi108_setup_pci(np);
+
+ ppc_md.pci_exclude_device = mpc7448_hpc2_exclude_device;
+ if (ppc_md.progress)
+ ppc_md.progress("tsi108: resources set", 0x100);
+#endif
+
+ printk(KERN_INFO "MPC7448HPC2 (TAIGA) Platform\n");
+ printk(KERN_INFO
+ "Jointly ported by Freescale and Tundra Semiconductor\n");
+ printk(KERN_INFO
+ "Enabling L2 cache then enabling the HID0 prefetch engine.\n");
+}
+
+/*
+ * Interrupt setup and service. Interrrupts on the mpc7448_hpc2 come
+ * from the four external INT pins, PCI interrupts are routed via
+ * PCI interrupt control registers, it generates internal IRQ23
+ *
+ * Interrupt routing on the Taiga Board:
+ * TSI108:PB_INT[0] -> CPU0:INT#
+ * TSI108:PB_INT[1] -> CPU0:MCP#
+ * TSI108:PB_INT[2] -> N/C
+ * TSI108:PB_INT[3] -> N/C
+ */
+static void __init mpc7448_hpc2_init_IRQ(void)
+{
+ struct mpic *mpic;
+ phys_addr_t mpic_paddr = 0;
+ struct device_node *tsi_pic;
+
+ tsi_pic = of_find_node_by_type(NULL, "open-pic");
+ if (tsi_pic) {
+ unsigned int size;
+ void *prop = get_property(tsi_pic, "reg", &size);
+ mpic_paddr = of_translate_address(tsi_pic, prop);
+ }
+
+ if (mpic_paddr == 0) {
+ printk("%s: No tsi108 PIC found !\n", __FUNCTION__);
+ return;
+ }
+
+ DBG("%s: tsi108pic phys_addr = 0x%x\n", __FUNCTION__,
+ (u32) mpic_paddr);
+
+ mpic = mpic_alloc(mpic_paddr,
+ MPIC_PRIMARY | MPIC_BIG_ENDIAN | MPIC_WANTS_RESET |
+ MPIC_SPV_EOI | MPIC_MOD_ID(MPIC_ID_TSI108),
+ 0, /* num_sources used */
+ TSI108_IRQ_BASE,
+ 0, /* num_sources used */
+ NR_IRQS - 4 /* XXXX */,
+ mpc7448_hpc2_pic_initsenses,
+ sizeof(mpc7448_hpc2_pic_initsenses), "Tsi108_PIC");
+
+ BUG_ON(mpic == NULL); /* XXXX */
+
+ mpic_init(mpic);
+ mpic_setup_cascade(IRQ_TSI108_PCI, tsi108_irq_cascade, mpic);
+ tsi108_pci_int_init();
+
+ /* Configure MPIC outputs to CPU0 */
+ tsi108_write_reg(TSI108_MPIC_OFFSET + 0x30c, 0);
+}
+
+void mpc7448_hpc2_show_cpuinfo(struct seq_file *m)
+{
+ seq_printf(m, "vendor\t\t: Freescale Semiconductor\n");
+ seq_printf(m, "machine\t\t: MPC7448hpc2\n");
+}
+
+void mpc7448_hpc2_restart(char *cmd)
+{
+ local_irq_disable();
+
+ /* Set exception prefix high - to the firmware */
+ _nmask_and_or_msr(0, MSR_IP);
+
+ for (;;) ; /* Spin until reset happens */
+}
+
+void mpc7448_hpc2_power_off(void)
+{
+ local_irq_disable();
+ for (;;) ; /* No way to shut power off with software */
+}
+
+void mpc7448_hpc2_halt(void)
+{
+ mpc7448_hpc2_power_off();
+}
+
+/*
+ * Called very early, device-tree isn't unflattened
+ */
+static int __init mpc7448_hpc2_probe(void)
+{
+ unsigned long root = of_get_flat_dt_root();
+
+ if (!of_flat_dt_is_compatible(root, "mpc74xx"))
+ return 0;
+ return 1;
+}
+
+static int mpc7448_machine_check_exception(struct pt_regs *regs)
+{
+ extern void tsi108_clear_pci_cfg_error(void);
+ const struct exception_table_entry *entry;
+
+ /* Are we prepared to handle this fault */
+ if ((entry = search_exception_tables(regs->nip)) != NULL) {
+ tsi108_clear_pci_cfg_error();
+ regs->msr |= MSR_RI;
+ regs->nip = entry->fixup;
+ return 1;
+ }
+ return 0;
+
+}
+define_machine(mpc7448_hpc2){
+ .name = "MPC7448 HPC2",
+ .probe = mpc7448_hpc2_probe,
+ .setup_arch = mpc7448_hpc2_setup_arch,
+ .init_IRQ = mpc7448_hpc2_init_IRQ,
+ .show_cpuinfo = mpc7448_hpc2_show_cpuinfo,
+ .get_irq = mpic_get_irq,
+ .pcibios_fixup = mpc7448_hpc2_pcibios_fixup,
+ .restart = mpc7448_hpc2_restart,
+ .calibrate_decr = generic_calibrate_decr,
+ .machine_check_exception= mpc7448_machine_check_exception,
+ .progress = udbg_progress,
+};
projects / linux-2.6 / commitdiff