#define IPATH_IB_LINK_LOOPBACK 6 /* enable local loopback */
#define IPATH_IB_LINK_EXTERNAL 7 /* normal, disable local loopback */
+/*
+ * These 3 values (SDR and DDR may be ORed for auto-speed
+ * negotiation) are used for the 3rd argument to path_f_set_ib_cfg
+ * with cmd IPATH_IB_CFG_SPD_ENB, by direct calls or via sysfs. They
+ * are also the the possible values for ipath_link_speed_enabled and active
+ * The values were chosen to match values used within the IB spec.
+ */
+#define IPATH_IB_SDR 1
+#define IPATH_IB_DDR 2
+
/*
* stats maintained by the driver. For now, at least, this is global
* to all minor devices.
#define INFINIPATH_HWE_HTAPLL_RFSLIP 0x1000000000000000ULL
#define INFINIPATH_HWE_SERDESPLLFAILED 0x2000000000000000ULL
+#define IBA6110_IBCS_LINKTRAININGSTATE_MASK 0xf
+#define IBA6110_IBCS_LINKSTATE_SHIFT 4
+
/* kr_extstatus bits */
#define INFINIPATH_EXTS_FREQSEL 0x2
#define INFINIPATH_EXTS_SERDESSEL 0x4
"with ID %u\n", boardrev);
snprintf(name, namelen, "Unknown_InfiniPath_QHT7xxx_%u",
boardrev);
- ret = 1;
break;
}
if (n)
static void ipath_init_ht_variables(struct ipath_devdata *dd)
{
+ /*
+ * setup the register offsets, since they are different for each
+ * chip
+ */
+ dd->ipath_kregs = &ipath_ht_kregs;
+ dd->ipath_cregs = &ipath_ht_cregs;
+
dd->ipath_gpio_sda_num = _IPATH_GPIO_SDA_NUM;
dd->ipath_gpio_scl_num = _IPATH_GPIO_SCL_NUM;
dd->ipath_gpio_sda = IPATH_GPIO_SDA;
dd->ipath_gpio_scl = IPATH_GPIO_SCL;
+ /*
+ * Fill in data for field-values that change in newer chips.
+ * We dynamically specify only the mask for LINKTRAININGSTATE
+ * and only the shift for LINKSTATE, as they are the only ones
+ * that change. Also precalculate the 3 link states of interest
+ * and the combined mask.
+ */
+ dd->ibcs_ls_shift = IBA6110_IBCS_LINKSTATE_SHIFT;
+ dd->ibcs_lts_mask = IBA6110_IBCS_LINKTRAININGSTATE_MASK;
+ dd->ibcs_mask = (INFINIPATH_IBCS_LINKSTATE_MASK <<
+ dd->ibcs_ls_shift) | dd->ibcs_lts_mask;
+ dd->ib_init = (INFINIPATH_IBCS_LT_STATE_LINKUP <<
+ INFINIPATH_IBCS_LINKTRAININGSTATE_SHIFT) |
+ (INFINIPATH_IBCS_L_STATE_INIT << dd->ibcs_ls_shift);
+ dd->ib_arm = (INFINIPATH_IBCS_LT_STATE_LINKUP <<
+ INFINIPATH_IBCS_LINKTRAININGSTATE_SHIFT) |
+ (INFINIPATH_IBCS_L_STATE_ARM << dd->ibcs_ls_shift);
+ dd->ib_active = (INFINIPATH_IBCS_LT_STATE_LINKUP <<
+ INFINIPATH_IBCS_LINKTRAININGSTATE_SHIFT) |
+ (INFINIPATH_IBCS_L_STATE_ACTIVE << dd->ibcs_ls_shift);
+
+ /*
+ * Fill in data for ibcc field-values that change in newer chips.
+ * We dynamically specify only the mask for LINKINITCMD
+ * and only the shift for LINKCMD and MAXPKTLEN, as they are
+ * the only ones that change.
+ */
+ dd->ibcc_lic_mask = INFINIPATH_IBCC_LINKINITCMD_MASK;
+ dd->ibcc_lc_shift = INFINIPATH_IBCC_LINKCMD_SHIFT;
+ dd->ibcc_mpl_shift = INFINIPATH_IBCC_MAXPKTLEN_SHIFT;
+
/* Fill in shifts for RcvCtrl. */
dd->ipath_r_portenable_shift = INFINIPATH_R_PORTENABLE_SHIFT;
dd->ipath_r_intravail_shift = INFINIPATH_R_INTRAVAIL_SHIFT;
dd->ipath_i_rcvavail_mask = INFINIPATH_I_RCVAVAIL_MASK;
dd->ipath_i_rcvurg_mask = INFINIPATH_I_RCVURG_MASK;
+ dd->ipath_i_rcvavail_shift = INFINIPATH_I_RCVAVAIL_SHIFT;
+ dd->ipath_i_rcvurg_shift = INFINIPATH_I_RCVURG_SHIFT;
/*
* EEPROM error log 0 is TXE Parity errors. 1 is RXE Parity.
INFINIPATH_HWE_RXEMEMPARITYERR_MASK <<
INFINIPATH_HWE_RXEMEMPARITYERR_SHIFT;
- dd->ipath_eep_st_masks[2].errs_to_log =
- INFINIPATH_E_INVALIDADDR | INFINIPATH_E_RESET;
+ dd->ipath_eep_st_masks[2].errs_to_log = INFINIPATH_E_RESET;
+ dd->delay_mult = 2; /* SDR, 4X, can't change */
+
+ dd->ipath_link_width_supported = IB_WIDTH_1X | IB_WIDTH_4X;
+ dd->ipath_link_speed_supported = IPATH_IB_SDR;
+ dd->ipath_link_width_enabled = IB_WIDTH_4X;
+ dd->ipath_link_speed_enabled = dd->ipath_link_speed_supported;
+ /* these can't change for this chip, so set once */
+ dd->ipath_link_width_active = dd->ipath_link_width_enabled;
+ dd->ipath_link_speed_active = dd->ipath_link_speed_enabled;
}
/**
dd->ipath_hwerrmask = val;
}
+
+
+
/**
* ipath_ht_bringup_serdes - bring up the serdes
* @dd: the infinipath device
pa |= lenvalid | INFINIPATH_RT_VALID;
}
}
+
writeq(pa, tidptr);
}
dd->ipath_intconfig = 0;
}
+static struct ipath_message_header *
+ipath_ht_get_msgheader(struct ipath_devdata *dd, __le32 *rhf_addr)
+{
+ return (struct ipath_message_header *)
+ &rhf_addr[sizeof(u64) / sizeof(u32)];
+}
+
static void ipath_ht_config_ports(struct ipath_devdata *dd, ushort cfgports)
{
dd->ipath_portcnt =
cntrs->RxDlidFltrCnt = 0;
}
+
+/* no interrupt fallback for these chips */
+static int ipath_ht_nointr_fallback(struct ipath_devdata *dd)
+{
+ return 0;
+}
+
+
+/*
+ * reset the XGXS (between serdes and IBC). Slightly less intrusive
+ * than resetting the IBC or external link state, and useful in some
+ * cases to cause some retraining. To do this right, we reset IBC
+ * as well.
+ */
+static void ipath_ht_xgxs_reset(struct ipath_devdata *dd)
+{
+ u64 val, prev_val;
+
+ prev_val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_xgxsconfig);
+ val = prev_val | INFINIPATH_XGXS_RESET;
+ prev_val &= ~INFINIPATH_XGXS_RESET; /* be sure */
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_control,
+ dd->ipath_control & ~INFINIPATH_C_LINKENABLE);
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_xgxsconfig, val);
+ ipath_read_kreg32(dd, dd->ipath_kregs->kr_scratch);
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_xgxsconfig, prev_val);
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_control,
+ dd->ipath_control);
+}
+
+
+static int ipath_ht_get_ib_cfg(struct ipath_devdata *dd, int which)
+{
+ int ret;
+
+ switch (which) {
+ case IPATH_IB_CFG_LWID:
+ ret = dd->ipath_link_width_active;
+ break;
+ case IPATH_IB_CFG_SPD:
+ ret = dd->ipath_link_speed_active;
+ break;
+ case IPATH_IB_CFG_LWID_ENB:
+ ret = dd->ipath_link_width_enabled;
+ break;
+ case IPATH_IB_CFG_SPD_ENB:
+ ret = dd->ipath_link_speed_enabled;
+ break;
+ default:
+ ret = -ENOTSUPP;
+ break;
+ }
+ return ret;
+}
+
+
+/* we assume range checking is already done, if needed */
+static int ipath_ht_set_ib_cfg(struct ipath_devdata *dd, int which, u32 val)
+{
+ int ret = 0;
+
+ if (which == IPATH_IB_CFG_LWID_ENB)
+ dd->ipath_link_width_enabled = val;
+ else if (which == IPATH_IB_CFG_SPD_ENB)
+ dd->ipath_link_speed_enabled = val;
+ else
+ ret = -ENOTSUPP;
+ return ret;
+}
+
+
+static void ipath_ht_config_jint(struct ipath_devdata *dd, u16 a, u16 b)
+{
+}
+
+
+static int ipath_ht_ib_updown(struct ipath_devdata *dd, int ibup, u64 ibcs)
+{
+ ipath_setup_ht_setextled(dd, ipath_ib_linkstate(dd, ibcs),
+ ipath_ib_linktrstate(dd, ibcs));
+ return 0;
+}
+
+
/**
* ipath_init_iba6110_funcs - set up the chip-specific function pointers
* @dd: the infinipath device
dd->ipath_f_setextled = ipath_setup_ht_setextled;
dd->ipath_f_get_base_info = ipath_ht_get_base_info;
dd->ipath_f_free_irq = ipath_ht_free_irq;
+ dd->ipath_f_tidtemplate = ipath_ht_tidtemplate;
+ dd->ipath_f_intr_fallback = ipath_ht_nointr_fallback;
+ dd->ipath_f_get_msgheader = ipath_ht_get_msgheader;
dd->ipath_f_config_ports = ipath_ht_config_ports;
dd->ipath_f_read_counters = ipath_ht_read_counters;
+ dd->ipath_f_xgxs_reset = ipath_ht_xgxs_reset;
+ dd->ipath_f_get_ib_cfg = ipath_ht_get_ib_cfg;
+ dd->ipath_f_set_ib_cfg = ipath_ht_set_ib_cfg;
+ dd->ipath_f_config_jint = ipath_ht_config_jint;
+ dd->ipath_f_ib_updown = ipath_ht_ib_updown;
/*
* initialize chip-specific variables
*/
- dd->ipath_f_tidtemplate = ipath_ht_tidtemplate;
-
- /*
- * setup the register offsets, since they are different for each
- * chip
- */
- dd->ipath_kregs = &ipath_ht_kregs;
- dd->ipath_cregs = &ipath_ht_cregs;
-
- /*
- * do very early init that is needed before ipath_f_bus is
- * called
- */
ipath_init_ht_variables(dd);
}
#define INFINIPATH_HWE_PCIE0PLLFAILED 0x0800000000000000ULL
#define INFINIPATH_HWE_SERDESPLLFAILED 0x1000000000000000ULL
+#define IBA6120_IBCS_LINKTRAININGSTATE_MASK 0xf
+#define IBA6120_IBCS_LINKSTATE_SHIFT 4
+
/* kr_extstatus bits */
#define INFINIPATH_EXTS_FREQSEL 0x2
#define INFINIPATH_EXTS_SERDESSEL 0x4
else
ipath_dev_err(dd, "Can't find PCI Express "
"capability!\n");
+
+ dd->ipath_link_width_supported = IB_WIDTH_1X | IB_WIDTH_4X;
+ dd->ipath_link_speed_supported = IPATH_IB_SDR;
+ dd->ipath_link_width_enabled = IB_WIDTH_4X;
+ dd->ipath_link_speed_enabled = dd->ipath_link_speed_supported;
+ /* these can't change for this chip, so set once */
+ dd->ipath_link_width_active = dd->ipath_link_width_enabled;
+ dd->ipath_link_speed_active = dd->ipath_link_speed_enabled;
return 0;
}
static void ipath_init_pe_variables(struct ipath_devdata *dd)
{
+ /*
+ * setup the register offsets, since they are different for each
+ * chip
+ */
+ dd->ipath_kregs = &ipath_pe_kregs;
+ dd->ipath_cregs = &ipath_pe_cregs;
+
/*
* bits for selecting i2c direction and values,
* used for I2C serial flash
dd->ipath_gpio_sda = IPATH_GPIO_SDA;
dd->ipath_gpio_scl = IPATH_GPIO_SCL;
+ /*
+ * Fill in data for field-values that change in newer chips.
+ * We dynamically specify only the mask for LINKTRAININGSTATE
+ * and only the shift for LINKSTATE, as they are the only ones
+ * that change. Also precalculate the 3 link states of interest
+ * and the combined mask.
+ */
+ dd->ibcs_ls_shift = IBA6120_IBCS_LINKSTATE_SHIFT;
+ dd->ibcs_lts_mask = IBA6120_IBCS_LINKTRAININGSTATE_MASK;
+ dd->ibcs_mask = (INFINIPATH_IBCS_LINKSTATE_MASK <<
+ dd->ibcs_ls_shift) | dd->ibcs_lts_mask;
+ dd->ib_init = (INFINIPATH_IBCS_LT_STATE_LINKUP <<
+ INFINIPATH_IBCS_LINKTRAININGSTATE_SHIFT) |
+ (INFINIPATH_IBCS_L_STATE_INIT << dd->ibcs_ls_shift);
+ dd->ib_arm = (INFINIPATH_IBCS_LT_STATE_LINKUP <<
+ INFINIPATH_IBCS_LINKTRAININGSTATE_SHIFT) |
+ (INFINIPATH_IBCS_L_STATE_ARM << dd->ibcs_ls_shift);
+ dd->ib_active = (INFINIPATH_IBCS_LT_STATE_LINKUP <<
+ INFINIPATH_IBCS_LINKTRAININGSTATE_SHIFT) |
+ (INFINIPATH_IBCS_L_STATE_ACTIVE << dd->ibcs_ls_shift);
+
+ /*
+ * Fill in data for ibcc field-values that change in newer chips.
+ * We dynamically specify only the mask for LINKINITCMD
+ * and only the shift for LINKCMD and MAXPKTLEN, as they are
+ * the only ones that change.
+ */
+ dd->ibcc_lic_mask = INFINIPATH_IBCC_LINKINITCMD_MASK;
+ dd->ibcc_lc_shift = INFINIPATH_IBCC_LINKCMD_SHIFT;
+ dd->ibcc_mpl_shift = INFINIPATH_IBCC_MAXPKTLEN_SHIFT;
+
/* Fill in shifts for RcvCtrl. */
dd->ipath_r_portenable_shift = INFINIPATH_R_PORTENABLE_SHIFT;
dd->ipath_r_intravail_shift = INFINIPATH_R_INTRAVAIL_SHIFT;
dd->ipath_i_rcvavail_mask = INFINIPATH_I_RCVAVAIL_MASK;
dd->ipath_i_rcvurg_mask = INFINIPATH_I_RCVURG_MASK;
+ dd->ipath_i_rcvavail_shift = INFINIPATH_I_RCVAVAIL_SHIFT;
+ dd->ipath_i_rcvurg_shift = INFINIPATH_I_RCVURG_SHIFT;
/*
* EEPROM error log 0 is TXE Parity errors. 1 is RXE Parity.
INFINIPATH_E_INVALIDADDR | INFINIPATH_E_RESET;
+ dd->delay_mult = 2; /* SDR, 4X, can't change */
}
/* setup the MSI stuff again after a reset. I'd like to just call
*/
dd->ipath_rcvhdrentsize = 24;
dd->ipath_rcvhdrsize = IPATH_DFLT_RCVHDRSIZE;
+ dd->ipath_rhf_offset = 0;
+ dd->ipath_egrtidbase = (u64 __iomem *)
+ ((char __iomem *) dd->ipath_kregbase + dd->ipath_rcvegrbase);
/*
* To truly support a 4KB MTU (for usermode), we need to
dd->ipath_irq = 0;
}
+
+static struct ipath_message_header *
+ipath_pe_get_msgheader(struct ipath_devdata *dd, __le32 *rhf_addr)
+{
+ return (struct ipath_message_header *)
+ &rhf_addr[sizeof(u64) / sizeof(u32)];
+}
+
static void ipath_pe_config_ports(struct ipath_devdata *dd, ushort cfgports)
{
dd->ipath_portcnt =
return 1;
}
+/* no interrupt fallback for these chips */
+static int ipath_pe_nointr_fallback(struct ipath_devdata *dd)
+{
+ return 0;
+}
+
+
+/*
+ * reset the XGXS (between serdes and IBC). Slightly less intrusive
+ * than resetting the IBC or external link state, and useful in some
+ * cases to cause some retraining. To do this right, we reset IBC
+ * as well.
+ */
+static void ipath_pe_xgxs_reset(struct ipath_devdata *dd)
+{
+ u64 val, prev_val;
+
+ prev_val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_xgxsconfig);
+ val = prev_val | INFINIPATH_XGXS_RESET;
+ prev_val &= ~INFINIPATH_XGXS_RESET; /* be sure */
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_control,
+ dd->ipath_control & ~INFINIPATH_C_LINKENABLE);
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_xgxsconfig, val);
+ ipath_read_kreg32(dd, dd->ipath_kregs->kr_scratch);
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_xgxsconfig, prev_val);
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_control,
+ dd->ipath_control);
+}
+
+
+static int ipath_pe_get_ib_cfg(struct ipath_devdata *dd, int which)
+{
+ int ret;
+
+ switch (which) {
+ case IPATH_IB_CFG_LWID:
+ ret = dd->ipath_link_width_active;
+ break;
+ case IPATH_IB_CFG_SPD:
+ ret = dd->ipath_link_speed_active;
+ break;
+ case IPATH_IB_CFG_LWID_ENB:
+ ret = dd->ipath_link_width_enabled;
+ break;
+ case IPATH_IB_CFG_SPD_ENB:
+ ret = dd->ipath_link_speed_enabled;
+ break;
+ default:
+ ret = -ENOTSUPP;
+ break;
+ }
+ return ret;
+}
+
+
+/* we assume range checking is already done, if needed */
+static int ipath_pe_set_ib_cfg(struct ipath_devdata *dd, int which, u32 val)
+{
+ int ret = 0;
+
+ if (which == IPATH_IB_CFG_LWID_ENB)
+ dd->ipath_link_width_enabled = val;
+ else if (which == IPATH_IB_CFG_SPD_ENB)
+ dd->ipath_link_speed_enabled = val;
+ else
+ ret = -ENOTSUPP;
+ return ret;
+}
+
+static void ipath_pe_config_jint(struct ipath_devdata *dd, u16 a, u16 b)
+{
+}
+
+
+static int ipath_pe_ib_updown(struct ipath_devdata *dd, int ibup, u64 ibcs)
+{
+ ipath_setup_pe_setextled(dd, ipath_ib_linkstate(dd, ibcs),
+ ipath_ib_linktrstate(dd, ibcs));
+ return 0;
+}
+
+
/**
* ipath_init_iba6120_funcs - set up the chip-specific function pointers
* @dd: the infinipath device
dd->ipath_f_bringup_serdes = ipath_pe_bringup_serdes;
dd->ipath_f_clear_tids = ipath_pe_clear_tids;
/*
- * this may get changed after we read the chip revision,
+ * _f_put_tid may get changed after we read the chip revision,
* but we start with the safe version for all revs
*/
dd->ipath_f_put_tid = ipath_pe_put_tid;
dd->ipath_f_setextled = ipath_setup_pe_setextled;
dd->ipath_f_get_base_info = ipath_pe_get_base_info;
dd->ipath_f_free_irq = ipath_pe_free_irq;
-
- /* initialize chip-specific variables */
dd->ipath_f_tidtemplate = ipath_pe_tidtemplate;
+ dd->ipath_f_intr_fallback = ipath_pe_nointr_fallback;
+ dd->ipath_f_xgxs_reset = ipath_pe_xgxs_reset;
+ dd->ipath_f_get_msgheader = ipath_pe_get_msgheader;
dd->ipath_f_config_ports = ipath_pe_config_ports;
dd->ipath_f_read_counters = ipath_pe_read_counters;
+ dd->ipath_f_get_ib_cfg = ipath_pe_get_ib_cfg;
+ dd->ipath_f_set_ib_cfg = ipath_pe_set_ib_cfg;
+ dd->ipath_f_config_jint = ipath_pe_config_jint;
+ dd->ipath_f_ib_updown = ipath_pe_ib_updown;
- /*
- * setup the register offsets, since they are different for each
- * chip
- */
- dd->ipath_kregs = &ipath_pe_kregs;
- dd->ipath_cregs = &ipath_pe_cregs;
+ /* initialize chip-specific variables */
ipath_init_pe_variables(dd);
}
dma_addr_t phys;
};
+/*
+ * Possible IB config parameters for ipath_f_get/set_ib_cfg()
+ */
+#define IPATH_IB_CFG_LIDLMC 0 /* Get/set LID (LS16b) and Mask (MS16b) */
+#define IPATH_IB_CFG_HRTBT 1 /* Get/set Heartbeat off/enable/auto */
+#define IPATH_IB_HRTBT_ON 3 /* Heartbeat enabled, sent every 100msec */
+#define IPATH_IB_HRTBT_OFF 0 /* Heartbeat off */
+#define IPATH_IB_CFG_LWID_ENB 2 /* Get/set allowed Link-width */
+#define IPATH_IB_CFG_LWID 3 /* Get currently active Link-width */
+#define IPATH_IB_CFG_SPD_ENB 4 /* Get/set allowed Link speeds */
+#define IPATH_IB_CFG_SPD 5 /* Get current Link spd */
+#define IPATH_IB_CFG_RXPOL_ENB 6 /* Get/set Auto-RX-polarity enable */
+#define IPATH_IB_CFG_LREV_ENB 7 /* Get/set Auto-Lane-reversal enable */
+#define IPATH_IB_CFG_LINKLATENCY 8 /* Get Auto-Lane-reversal enable */
+
+
struct ipath_devdata {
struct list_head ipath_list;
struct _ipath_layer ipath_layer;
/* setup intr */
int (*ipath_f_intrsetup)(struct ipath_devdata *);
+ /* fallback to alternate interrupt type if possible */
+ int (*ipath_f_intr_fallback)(struct ipath_devdata *);
/* setup on-chip bus config */
int (*ipath_f_bus)(struct ipath_devdata *, struct pci_dev *);
/* hard reset chip */
int (*ipath_f_get_base_info)(struct ipath_portdata *, void *);
/* free irq */
void (*ipath_f_free_irq)(struct ipath_devdata *);
+ struct ipath_message_header *(*ipath_f_get_msgheader)
+ (struct ipath_devdata *, __le32 *);
void (*ipath_f_config_ports)(struct ipath_devdata *, ushort);
+ int (*ipath_f_get_ib_cfg)(struct ipath_devdata *, int);
+ int (*ipath_f_set_ib_cfg)(struct ipath_devdata *, int, u32);
+ void (*ipath_f_config_jint)(struct ipath_devdata *, u16 , u16);
void (*ipath_f_read_counters)(struct ipath_devdata *,
- struct infinipath_counters *);
+ struct infinipath_counters *);
+ void (*ipath_f_xgxs_reset)(struct ipath_devdata *);
+ /* per chip actions needed for IB Link up/down changes */
+ int (*ipath_f_ib_updown)(struct ipath_devdata *, int, u64);
+
struct ipath_ibdev *verbs_dev;
struct timer_list verbs_timer;
/* total dwords sent (summed from counter) */
struct page **ipath_pageshadow;
/* shadow copy of dma handles for exp tid pages */
dma_addr_t *ipath_physshadow;
+ u64 __iomem *ipath_egrtidbase;
/* lock to workaround chip bug 9437 */
spinlock_t ipath_tid_lock;
spinlock_t ipath_sendctrl_lock;
u8 ipath_pci_cacheline;
/* LID mask control */
u8 ipath_lmc;
+ /* link width supported */
+ u8 ipath_link_width_supported;
+ /* link speed supported */
+ u8 ipath_link_speed_supported;
+ u8 ipath_link_width_enabled;
+ u8 ipath_link_speed_enabled;
+ u8 ipath_link_width_active;
+ u8 ipath_link_speed_active;
/* Rx Polarity inversion (compensate for ~tx on partner) */
u8 ipath_rx_pol_inv;
*/
u32 ipath_i_rcvavail_mask;
u32 ipath_i_rcvurg_mask;
+ u16 ipath_i_rcvurg_shift;
+ u16 ipath_i_rcvavail_shift;
/*
* Register bits for selecting i2c direction and values, used for
/* lock for doing RMW of shadows/regs for ExtCtrl and GPIO */
spinlock_t ipath_gpio_lock;
+ /*
+ * IB link and linktraining states and masks that vary per chip in
+ * some way. Set at init, to avoid each IB status change interrupt
+ */
+ u8 ibcs_ls_shift;
+ u8 ibcs_lts_mask;
+ u32 ibcs_mask;
+ u32 ib_init;
+ u32 ib_arm;
+ u32 ib_active;
+
+ u16 ipath_rhf_offset; /* offset of RHF within receive header entry */
+
+ /*
+ * shift/mask for linkcmd, linkinitcmd, maxpktlen in ibccontol
+ * reg. Changes for IBA7220
+ */
+ u8 ibcc_lic_mask; /* LinkInitCmd */
+ u8 ibcc_lc_shift; /* LinkCmd */
+ u8 ibcc_mpl_shift; /* Maxpktlen */
+
+ u8 delay_mult;
+
/* used to override LED behavior */
u8 ipath_led_override; /* Substituted for normal value, if non-zero */
u16 ipath_led_override_timeoff; /* delta to next timer event */
* each of the counters to increment.
*/
struct ipath_eep_log_mask ipath_eep_st_masks[IPATH_EEP_LOG_CNT];
+
+ /* interrupt mitigation reload register info */
+ u16 ipath_jint_idle_ticks; /* idle clock ticks */
+ u16 ipath_jint_max_packets; /* max packets across all ports */
};
/* Private data for file operations */
ipath_read_kreg64(dd, r) : ipath_read_kreg32(dd, r);
}
+/*
+ * from contents of IBCStatus (or a saved copy), return linkstate
+ * Report ACTIVE_DEFER as ACTIVE, because we treat them the same
+ * everywhere, anyway (and should be, for almost all purposes).
+ */
+static inline u32 ipath_ib_linkstate(struct ipath_devdata *dd, u64 ibcs)
+{
+ u32 state = (u32)(ibcs >> dd->ibcs_ls_shift) &
+ INFINIPATH_IBCS_LINKSTATE_MASK;
+ if (state == INFINIPATH_IBCS_L_STATE_ACT_DEFER)
+ state = INFINIPATH_IBCS_L_STATE_ACTIVE;
+ return state;
+}
+
+/* from contents of IBCStatus (or a saved copy), return linktrainingstate */
+static inline u32 ipath_ib_linktrstate(struct ipath_devdata *dd, u64 ibcs)
+{
+ return (u32)(ibcs >> INFINIPATH_IBCS_LINKTRAININGSTATE_SHIFT) &
+ dd->ibcs_lts_mask;
+}
+
/*
* sysfs interface.
*/
projects / linux-2.6 / commitdiff