#
-# Copyright 2000,2001 MontaVista Software Inc.
-# Author: MontaVista Software, Inc.
-# ppopov@mvista.com or source@mvista.com
+# Copyright 2000, 2001, 2008 MontaVista Software Inc.
+# Author: MontaVista Software, Inc. <source@mvista.com>
#
# Makefile for the Alchemy Semiconductor Pb1100 board.
+#
lib-y := init.o board_setup.o irqmap.o
/*
- * Copyright 2002 MontaVista Software Inc.
- * Author: MontaVista Software, Inc.
- * ppopov@mvista.com or source@mvista.com
+ * Copyright 2002, 2008 MontaVista Software Inc.
+ * Author: MontaVista Software, Inc. <source@mvista.com>
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
void board_reset(void)
{
- /* Hit BCSR.SYSTEM_CONTROL[SW_RST] */
- au_writel(0x00000000, 0xAE00001C);
+ /* Hit BCSR.RST_VDDI[SOFT_RESET] */
+ au_writel(0x00000000, PB1100_RST_VDDI);
}
void __init board_setup(void)
{
- volatile void __iomem * base = (volatile void __iomem *) 0xac000000UL;
+ volatile void __iomem *base = (volatile void __iomem *)0xac000000UL;
- // set AUX clock to 12MHz * 8 = 96 MHz
+ /* Set AUX clock to 12 MHz * 8 = 96 MHz */
au_writel(8, SYS_AUXPLL);
au_writel(0, SYS_PININPUTEN);
udelay(100);
{
u32 pin_func, sys_freqctrl, sys_clksrc;
- // configure pins GPIO[14:9] as GPIO
- pin_func = au_readl(SYS_PINFUNC) & (u32)(~0x80);
+ /* Configure pins GPIO[14:9] as GPIO */
+ pin_func = au_readl(SYS_PINFUNC) & ~SYS_PF_UR3;
- /* zero and disable FREQ2 */
+ /* Zero and disable FREQ2 */
sys_freqctrl = au_readl(SYS_FREQCTRL0);
sys_freqctrl &= ~0xFFF00000;
au_writel(sys_freqctrl, SYS_FREQCTRL0);
- /* zero and disable USBH/USBD/IrDA clock */
+ /* Zero and disable USBH/USBD/IrDA clock */
sys_clksrc = au_readl(SYS_CLKSRC);
- sys_clksrc &= ~0x0000001F;
+ sys_clksrc &= ~(SYS_CS_CIR | SYS_CS_DIR | SYS_CS_MIR_MASK);
au_writel(sys_clksrc, SYS_CLKSRC);
sys_freqctrl = au_readl(SYS_FREQCTRL0);
sys_freqctrl &= ~0xFFF00000;
sys_clksrc = au_readl(SYS_CLKSRC);
- sys_clksrc &= ~0x0000001F;
+ sys_clksrc &= ~(SYS_CS_CIR | SYS_CS_DIR | SYS_CS_MIR_MASK);
- // FREQ2 = aux/2 = 48 MHz
- sys_freqctrl |= ((0<<22) | (1<<21) | (1<<20));
+ /* FREQ2 = aux / 2 = 48 MHz */
+ sys_freqctrl |= (0 << SYS_FC_FRDIV2_BIT) |
+ SYS_FC_FE2 | SYS_FC_FS2;
au_writel(sys_freqctrl, SYS_FREQCTRL0);
/*
- * Route 48MHz FREQ2 into USBH/USBD/IrDA
+ * Route 48 MHz FREQ2 into USBH/USBD/IrDA
*/
- sys_clksrc |= ((4<<2) | (0<<1) | 0 );
+ sys_clksrc |= SYS_CS_MUX_FQ2 << SYS_CS_MIR_BIT;
au_writel(sys_clksrc, SYS_CLKSRC);
- /* setup the static bus controller */
+ /* Setup the static bus controller */
au_writel(0x00000002, MEM_STCFG3); /* type = PCMCIA */
au_writel(0x280E3D07, MEM_STTIME3); /* 250ns cycle time */
au_writel(0x10000000, MEM_STADDR3); /* any PCMCIA select */
- // get USB Functionality pin state (device vs host drive pins)
- pin_func = au_readl(SYS_PINFUNC) & (u32)(~0x8000);
- // 2nd USB port is USB host
- pin_func |= 0x8000;
+ /*
+ * Get USB Functionality pin state (device vs host drive pins).
+ */
+ pin_func = au_readl(SYS_PINFUNC) & ~SYS_PF_USB;
+ /* 2nd USB port is USB host. */
+ pin_func |= SYS_PF_USB;
au_writel(pin_func, SYS_PINFUNC);
}
#endif /* defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) */
/* Enable sys bus clock divider when IDLE state or no bus activity. */
au_writel(au_readl(SYS_POWERCTRL) | (0x3 << 5), SYS_POWERCTRL);
- // Enable the RTC if not already enabled
+ /* Enable the RTC if not already enabled. */
if (!(readb(base + 0x28) & 0x20)) {
writeb(readb(base + 0x28) | 0x20, base + 0x28);
au_sync();
}
- // Put the clock in BCD mode
+ /* Put the clock in BCD mode. */
if (readb(base + 0x2C) & 0x4) { /* reg B */
writeb(readb(base + 0x2c) & ~0x4, base + 0x2c);
au_sync();
* BRIEF MODULE DESCRIPTION
* Pb1100 board setup
*
- * Copyright 2002 MontaVista Software Inc.
- * Author: MontaVista Software, Inc.
- * ppopov@mvista.com or source@mvista.com
+ * Copyright 2002, 2008 MontaVista Software Inc.
+ * Author: MontaVista Software, Inc. <source@mvista.com>
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
unsigned long memsize;
prom_argc = fw_arg0;
- prom_argv = (char **) fw_arg1;
- prom_envp = (char **) fw_arg3;
+ prom_argv = (char **)fw_arg1;
+ prom_envp = (char **)fw_arg3;
prom_init_cmdline();
if (!memsize_str)
memsize = 0x04000000;
else
- memsize = simple_strtol(memsize_str, NULL, 0);
+ memsize = strict_strtol(memsize_str, 0, NULL);
add_memory_region(0, memsize, BOOT_MEM_RAM);
}
/*
* BRIEF MODULE DESCRIPTION
- * Au1xxx irq map table
+ * Au1xx0 IRQ map table
*
* Copyright 2003 Embedded Edge, LLC
* dan@embeddededge.com
#include <asm/mach-au1x00/au1000.h>
struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
- { AU1000_GPIO_9, INTC_INT_LOW_LEVEL, 0 }, // PCMCIA Card Fully_Interted#
- { AU1000_GPIO_10, INTC_INT_LOW_LEVEL, 0 }, // PCMCIA Card STSCHG#
- { AU1000_GPIO_11, INTC_INT_LOW_LEVEL, 0 }, // PCMCIA Card IRQ#
- { AU1000_GPIO_13, INTC_INT_LOW_LEVEL, 0 }, // DC_IRQ#
+ { AU1000_GPIO_9, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card Fully_Inserted# */
+ { AU1000_GPIO_10, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card STSCHG# */
+ { AU1000_GPIO_11, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card IRQ# */
+ { AU1000_GPIO_13, INTC_INT_LOW_LEVEL, 0 }, /* DC_IRQ# */
};
int __initdata au1xxx_nr_irqs = ARRAY_SIZE(au1xxx_irq_map);
/*
- * Alchemy Semi PB1100 Referrence Board
+ * Alchemy Semi Pb1100 Referrence Board
*
- * Copyright 2001 MontaVista Software Inc.
- * Author: MontaVista Software, Inc.
- * ppopov@mvista.com or source@mvista.com
+ * Copyright 2001, 2008 MontaVista Software Inc.
+ * Author: MontaVista Software, Inc. <source@mvista.com>
*
* ########################################################################
*
#ifndef __ASM_PB1100_H
#define __ASM_PB1100_H
-#define PB1100_IDENT 0xAE000000
-#define BOARD_STATUS_REG 0xAE000004
-# define PB1100_ROM_SEL (1<<15)
-# define PB1100_ROM_SIZ (1<<14)
-# define PB1100_SWAP_BOOT (1<<13)
-# define PB1100_FLASH_WP (1<<12)
-# define PB1100_ROM_H_STS (1<<11)
-# define PB1100_ROM_L_STS (1<<10)
-# define PB1100_FLASH_H_STS (1<<9)
-# define PB1100_FLASH_L_STS (1<<8)
-# define PB1100_SRAM_SIZ (1<<7)
-# define PB1100_TSC_BUSY (1<<6)
-# define PB1100_PCMCIA_VS_MASK (3<<4)
-# define PB1100_RS232_CD (1<<3)
-# define PB1100_RS232_CTS (1<<2)
-# define PB1100_RS232_DSR (1<<1)
-# define PB1100_RS232_RI (1<<0)
+#define PB1100_IDENT 0xAE000000
+#define BOARD_STATUS_REG 0xAE000004
+# define PB1100_ROM_SEL (1 << 15)
+# define PB1100_ROM_SIZ (1 << 14)
+# define PB1100_SWAP_BOOT (1 << 13)
+# define PB1100_FLASH_WP (1 << 12)
+# define PB1100_ROM_H_STS (1 << 11)
+# define PB1100_ROM_L_STS (1 << 10)
+# define PB1100_FLASH_H_STS (1 << 9)
+# define PB1100_FLASH_L_STS (1 << 8)
+# define PB1100_SRAM_SIZ (1 << 7)
+# define PB1100_TSC_BUSY (1 << 6)
+# define PB1100_PCMCIA_VS_MASK (3 << 4)
+# define PB1100_RS232_CD (1 << 3)
+# define PB1100_RS232_CTS (1 << 2)
+# define PB1100_RS232_DSR (1 << 1)
+# define PB1100_RS232_RI (1 << 0)
-#define PB1100_IRDA_RS232 0xAE00000C
-# define PB1100_IRDA_FULL (0<<14) /* full power */
-# define PB1100_IRDA_SHUTDOWN (1<<14)
-# define PB1100_IRDA_TT (2<<14) /* 2/3 power */
-# define PB1100_IRDA_OT (3<<14) /* 1/3 power */
-# define PB1100_IRDA_FIR (1<<13)
+#define PB1100_IRDA_RS232 0xAE00000C
+# define PB1100_IRDA_FULL (0 << 14) /* full power */
+# define PB1100_IRDA_SHUTDOWN (1 << 14)
+# define PB1100_IRDA_TT (2 << 14) /* 2/3 power */
+# define PB1100_IRDA_OT (3 << 14) /* 1/3 power */
+# define PB1100_IRDA_FIR (1 << 13)
-#define PCMCIA_BOARD_REG 0xAE000010
-# define PB1100_SD_WP1_RO (1<<15) /* read only */
-# define PB1100_SD_WP0_RO (1<<14) /* read only */
-# define PB1100_SD_PWR1 (1<<11) /* applies power to SD1 */
-# define PB1100_SD_PWR0 (1<<10) /* applies power to SD0 */
-# define PB1100_SEL_SD_CONN1 (1<<9)
-# define PB1100_SEL_SD_CONN0 (1<<8)
-# define PC_DEASSERT_RST (1<<7)
-# define PC_DRV_EN (1<<4)
+#define PCMCIA_BOARD_REG 0xAE000010
+# define PB1100_SD_WP1_RO (1 << 15) /* read only */
+# define PB1100_SD_WP0_RO (1 << 14) /* read only */
+# define PB1100_SD_PWR1 (1 << 11) /* applies power to SD1 */
+# define PB1100_SD_PWR0 (1 << 10) /* applies power to SD0 */
+# define PB1100_SEL_SD_CONN1 (1 << 9)
+# define PB1100_SEL_SD_CONN0 (1 << 8)
+# define PC_DEASSERT_RST (1 << 7)
+# define PC_DRV_EN (1 << 4)
-#define PB1100_G_CONTROL 0xAE000014 /* graphics control */
+#define PB1100_G_CONTROL 0xAE000014 /* graphics control */
-#define PB1100_RST_VDDI 0xAE00001C
-# define PB1100_SOFT_RESET (1<<15) /* clear to reset the board */
-# define PB1100_VDDI_MASK (0x1F)
+#define PB1100_RST_VDDI 0xAE00001C
+# define PB1100_SOFT_RESET (1 << 15) /* clear to reset the board */
+# define PB1100_VDDI_MASK 0x1F
-#define PB1100_LEDS 0xAE000018
+#define PB1100_LEDS 0xAE000018
-/* 11:8 is 4 discreet LEDs. Clearing a bit illuminates the LED.
- * 7:0 is the LED Display's decimal points.
+/*
+ * 11:8 is 4 discreet LEDs. Clearing a bit illuminates the LED.
+ * 7:0 is the LED Display's decimal points.
*/
-#define PB1100_HEX_LED 0xAE000018
+#define PB1100_HEX_LED 0xAE000018
-/* PCMCIA PB1100 specific defines */
-#define PCMCIA_MAX_SOCK 0
-#define PCMCIA_NUM_SOCKS (PCMCIA_MAX_SOCK+1)
+/* PCMCIA Pb1100 specific defines */
+#define PCMCIA_MAX_SOCK 0
+#define PCMCIA_NUM_SOCKS (PCMCIA_MAX_SOCK + 1)
/* VPP/VCC */
-#define SET_VCC_VPP(VCC, VPP) (((VCC)<<2) | ((VPP)<<0))
+#define SET_VCC_VPP(VCC, VPP) (((VCC) << 2) | ((VPP) << 0))
#endif /* __ASM_PB1100_H */
projects / linux-2.6 / commitdiff