[MIPS] MTX1: add idsel cardbus ressources

Adds cardbus ressources for MTX1 boards which have a PCMCIA controller.

Signed-off-by: Florian Fainelli <florian.fainelli@int-evry.fr>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

diff --git a/arch/mips/au1000/mtx-1/board_setup.c b/arch/mips/au1000/mtx-1/board_setup.c
index 7a3cf72c51aa14a7138b7d9a59278b5a3159a9e0..7bc5af8917dafacde69719fa6fafb14ff0eed8d1 100644 (file)
--- a/arch/mips/au1000/mtx-1/board_setup.c
+++ b/arch/mips/au1000/mtx-1/board_setup.c
@@ -43,6 +43,9 @@
 #include <asm/pgtable.h>
 #include <asm/mach-au1x00/au1000.h>
 
+extern int (*board_pci_idsel)(unsigned int devsel, int assert);
+int    mtx1_pci_idsel(unsigned int devsel, int assert);
+
 void board_reset (void)
 {
        /* Hit BCSR.SYSTEM_CONTROL[SW_RST] */
@@ -72,11 +75,37 @@ void __init board_setup(void)
        au_writel( 0xFFFFFFFF, SYS_TRIOUTCLR );
        au_writel( 0x00000001, SYS_OUTPUTCLR ); // set M66EN (PCI 66MHz) to OFF
        au_writel( 0x00000008, SYS_OUTPUTSET ); // set PCI CLKRUN# to OFF
+       au_writel( 0x00000002, SYS_OUTPUTSET ); // set EXT_IO3 ON
        au_writel( 0x00000020, SYS_OUTPUTCLR ); // set eth PHY TX_ER to OFF
 
        // enable LED and set it to green
        au_writel( au_readl(GPIO2_DIR) | 0x1800, GPIO2_DIR );
        au_writel( 0x18000800, GPIO2_OUTPUT );
 
+       board_pci_idsel = mtx1_pci_idsel;
+
        printk("4G Systems MTX-1 Board\n");
 }
+
+int
+mtx1_pci_idsel(unsigned int devsel, int assert)
+{
+#define MTX_IDSEL_ONLY_0_AND_3 0
+#if MTX_IDSEL_ONLY_0_AND_3
+       if (devsel != 0 && devsel != 3) {
+               printk("*** not 0 or 3\n");
+               return 0;
+       }
+#endif
+
+       if (assert && devsel != 0) {
+               // supress signal to cardbus
+               au_writel( 0x00000002, SYS_OUTPUTCLR ); // set EXT_IO3 OFF
+       }
+       else {
+               au_writel( 0x00000002, SYS_OUTPUTSET ); // set EXT_IO3 ON
+       }
+       au_sync_udelay(1);
+       return 1;
+}
+

diff --git a/arch/mips/au1000/mtx-1/irqmap.c b/arch/mips/au1000/mtx-1/irqmap.c
index 4693a4eb2b829972966a0ee1306b54cb07ade10e..a4fa0f227e420d2958b8645a109bd0bd3688e79c 100644 (file)
--- a/arch/mips/au1000/mtx-1/irqmap.c
+++ b/arch/mips/au1000/mtx-1/irqmap.c
@@ -48,7 +48,7 @@
 #include <asm/mach-au1x00/au1000.h>
 
 char irq_tab_alchemy[][5] __initdata = {
- [0] = { -1, INTA, INTB, INTX, INTX},   /* IDSEL 00 - AdapterA-Slot0 (top)    */
+ [0] = { -1, INTA, INTA, INTX, INTX},   /* IDSEL 00 - AdapterA-Slot0 (top)    */
  [1] = { -1, INTB, INTA, INTX, INTX},   /* IDSEL 01 - AdapterA-Slot1 (bottom) */
  [2] = { -1, INTC, INTD, INTX, INTX},   /* IDSEL 02 - AdapterB-Slot0 (top)    */
  [3] = { -1, INTD, INTC, INTX, INTX},   /* IDSEL 03 - AdapterB-Slot1 (bottom) */