return value;
}
+/* RC5 decoding stuff, moved from bttv-input.c to share it with
+ * saa7134 */
+
+/* decode raw bit pattern to RC5 code */
+u32 ir_rc5_decode(unsigned int code)
+{
+ unsigned int org_code = code;
+ unsigned int pair;
+ unsigned int rc5 = 0;
+ int i;
+
+ for (i = 0; i < 14; ++i) {
+ pair = code & 0x3;
+ code >>= 2;
+
+ rc5 <<= 1;
+ switch (pair) {
+ case 0:
+ case 2:
+ break;
+ case 1:
+ rc5 |= 1;
+ break;
+ case 3:
+ dprintk(1, "ir-common: ir_rc5_decode(%x) bad code\n", org_code);
+ return 0;
+ }
+ }
+ dprintk(1, "ir-common: code=%x, rc5=%x, start=%x, toggle=%x, address=%x, "
+ "instr=%x\n", rc5, org_code, RC5_START(rc5),
+ RC5_TOGGLE(rc5), RC5_ADDR(rc5), RC5_INSTR(rc5));
+ return rc5;
+}
+
+void ir_rc5_timer_end(unsigned long data)
+{
+ struct card_ir *ir = (struct card_ir *)data;
+ struct timeval tv;
+ unsigned long current_jiffies, timeout;
+ u32 gap;
+ u32 rc5 = 0;
+
+ /* get time */
+ current_jiffies = jiffies;
+ do_gettimeofday(&tv);
+
+ /* avoid overflow with gap >1s */
+ if (tv.tv_sec - ir->base_time.tv_sec > 1) {
+ gap = 200000;
+ } else {
+ gap = 1000000 * (tv.tv_sec - ir->base_time.tv_sec) +
+ tv.tv_usec - ir->base_time.tv_usec;
+ }
+
+ /* Allow some timmer jitter (RC5 is ~24ms anyway so this is ok) */
+ if (gap < 28000) {
+ dprintk(1, "ir-common: spurious timer_end\n");
+ return;
+ }
+
+ ir->active = 0;
+ if (ir->last_bit < 20) {
+ /* ignore spurious codes (caused by light/other remotes) */
+ dprintk(1, "ir-common: short code: %x\n", ir->code);
+ } else {
+ ir->code = (ir->code << ir->shift_by) | 1;
+ rc5 = ir_rc5_decode(ir->code);
+
+ /* two start bits? */
+ if (RC5_START(rc5) != ir->start) {
+ dprintk(1, "ir-common: rc5 start bits invalid: %u\n", RC5_START(rc5));
+
+ /* right address? */
+ } else if (RC5_ADDR(rc5) == ir->addr) {
+ u32 toggle = RC5_TOGGLE(rc5);
+ u32 instr = RC5_INSTR(rc5);
+
+ /* Good code, decide if repeat/repress */
+ if (toggle != RC5_TOGGLE(ir->last_rc5) ||
+ instr != RC5_INSTR(ir->last_rc5)) {
+ dprintk(1, "ir-common: instruction %x, toggle %x\n", instr,
+ toggle);
+ ir_input_nokey(ir->dev, &ir->ir);
+ ir_input_keydown(ir->dev, &ir->ir, instr,
+ instr);
+ }
+
+ /* Set/reset key-up timer */
+ timeout = current_jiffies + (500 + ir->rc5_key_timeout
+ * HZ) / 1000;
+ mod_timer(&ir->timer_keyup, timeout);
+
+ /* Save code for repeat test */
+ ir->last_rc5 = rc5;
+ }
+ }
+}
+
+void ir_rc5_timer_keyup(unsigned long data)
+{
+ struct card_ir *ir = (struct card_ir *)data;
+
+ dprintk(1, "ir-common: key released\n");
+ ir_input_nokey(ir->dev, &ir->ir);
+}
+
EXPORT_SYMBOL_GPL(ir_input_init);
EXPORT_SYMBOL_GPL(ir_input_nokey);
EXPORT_SYMBOL_GPL(ir_input_keydown);
EXPORT_SYMBOL_GPL(ir_decode_biphase);
EXPORT_SYMBOL_GPL(ir_decode_pulsedistance);
+EXPORT_SYMBOL_GPL(ir_rc5_decode);
+EXPORT_SYMBOL_GPL(ir_rc5_timer_end);
+EXPORT_SYMBOL_GPL(ir_rc5_timer_keyup);
+
/*
* Local variables:
* c-basic-offset: 8
};
EXPORT_SYMBOL_GPL(ir_codes_budget_ci_old);
+
+/*
+ * Marc Fargas <telenieko@telenieko.com>
+ * this is the remote control that comes with the asus p7131
+ * which has a label saying is "Model PC-39"
+ */
+IR_KEYTAB_TYPE ir_codes_asus_pc39[IR_KEYTAB_SIZE] = {
+ /* Keys 0 to 9 */
+ [ 0x15 ] = KEY_0,
+ [ 0x29 ] = KEY_1,
+ [ 0x2d ] = KEY_2,
+ [ 0x2b ] = KEY_3,
+ [ 0x09 ] = KEY_4,
+ [ 0x0d ] = KEY_5,
+ [ 0x0b ] = KEY_6,
+ [ 0x31 ] = KEY_7,
+ [ 0x35 ] = KEY_8,
+ [ 0x33 ] = KEY_9,
+
+ [ 0x3e ] = KEY_RADIO, /* radio */
+ [ 0x03 ] = KEY_MENU, /* dvd/menu */
+ [ 0x2a ] = KEY_VOLUMEUP,
+ [ 0x19 ] = KEY_VOLUMEDOWN,
+ [ 0x37 ] = KEY_UP,
+ [ 0x3b ] = KEY_DOWN,
+ [ 0x27 ] = KEY_LEFT,
+ [ 0x2f ] = KEY_RIGHT,
+ [ 0x25 ] = KEY_VIDEO, /* video */
+ [ 0x39 ] = KEY_AUDIO, /* music */
+
+ [ 0x21 ] = KEY_TV, /* tv */
+ [ 0x1d ] = KEY_EXIT, /* back */
+ [ 0x0a ] = KEY_CHANNELUP, /* channel / program + */
+ [ 0x1b ] = KEY_CHANNELDOWN, /* channel / program - */
+ [ 0x1a ] = KEY_ENTER, /* enter */
+
+ [ 0x06 ] = KEY_PAUSE, /* play/pause */
+ [ 0x1e ] = KEY_PREVIOUS, /* rew */
+ [ 0x26 ] = KEY_NEXT, /* forward */
+ [ 0x0e ] = KEY_REWIND, /* backward << */
+ [ 0x3a ] = KEY_FASTFORWARD, /* forward >> */
+ [ 0x36 ] = KEY_STOP,
+ [ 0x2e ] = KEY_RECORD, /* recording */
+ [ 0x16 ] = KEY_POWER, /* the button that reads "close" */
+
+ [ 0x11 ] = KEY_ZOOM, /* full screen */
+ [ 0x13 ] = KEY_MACRO, /* recall */
+ [ 0x23 ] = KEY_HOME, /* home */
+ [ 0x05 ] = KEY_PVR, /* picture */
+ [ 0x3d ] = KEY_MUTE, /* mute */
+ [ 0x01 ] = KEY_DVD, /* dvd */
+};
+
+EXPORT_SYMBOL_GPL(ir_codes_asus_pc39);
static int repeat_period = 33;
module_param(repeat_period, int, 0644);
+int ir_rc5_remote_gap = 885;
+module_param(ir_rc5_remote_gap, int, 0644);
+int ir_rc5_key_timeout = 200;
+module_param(ir_rc5_key_timeout, int, 0644);
+
#define DEVNAME "bttv-input"
/* ---------------------------------------------------------------------- */
static void ir_handle_key(struct bttv *btv)
{
- struct bttv_ir *ir = btv->remote;
+ struct card_ir *ir = btv->remote;
u32 gpio,data;
/* read gpio value */
void bttv_input_irq(struct bttv *btv)
{
- struct bttv_ir *ir = btv->remote;
+ struct card_ir *ir = btv->remote;
if (!ir->polling)
ir_handle_key(btv);
static void bttv_input_timer(unsigned long data)
{
struct bttv *btv = (struct bttv*)data;
- struct bttv_ir *ir = btv->remote;
+ struct card_ir *ir = btv->remote;
unsigned long timeout;
ir_handle_key(btv);
/* ---------------------------------------------------------------*/
-static int rc5_remote_gap = 885;
-module_param(rc5_remote_gap, int, 0644);
-static int rc5_key_timeout = 200;
-module_param(rc5_key_timeout, int, 0644);
-
-#define RC5_START(x) (((x)>>12)&3)
-#define RC5_TOGGLE(x) (((x)>>11)&1)
-#define RC5_ADDR(x) (((x)>>6)&31)
-#define RC5_INSTR(x) ((x)&63)
-
-/* decode raw bit pattern to RC5 code */
-static u32 rc5_decode(unsigned int code)
-{
- unsigned int org_code = code;
- unsigned int pair;
- unsigned int rc5 = 0;
- int i;
-
- code = (code << 1) | 1;
- for (i = 0; i < 14; ++i) {
- pair = code & 0x3;
- code >>= 2;
-
- rc5 <<= 1;
- switch (pair) {
- case 0:
- case 2:
- break;
- case 1:
- rc5 |= 1;
- break;
- case 3:
- dprintk(KERN_WARNING "bad code: %x\n", org_code);
- return 0;
- }
- }
- dprintk(KERN_WARNING "code=%x, rc5=%x, start=%x, toggle=%x, address=%x, "
- "instr=%x\n", rc5, org_code, RC5_START(rc5),
- RC5_TOGGLE(rc5), RC5_ADDR(rc5), RC5_INSTR(rc5));
- return rc5;
-}
-
static int bttv_rc5_irq(struct bttv *btv)
{
- struct bttv_ir *ir = btv->remote;
+ struct card_ir *ir = btv->remote;
struct timeval tv;
u32 gpio;
u32 gap;
/* only if in the code (otherwise spurious IRQ or timer
late) */
if (ir->last_bit < 28) {
- ir->last_bit = (gap - rc5_remote_gap / 2) /
- rc5_remote_gap;
+ ir->last_bit = (gap - ir_rc5_remote_gap / 2) /
+ ir_rc5_remote_gap;
ir->code |= 1 << ir->last_bit;
}
/* starting new code */
return 1;
}
-
-static void bttv_rc5_timer_end(unsigned long data)
-{
- struct bttv_ir *ir = (struct bttv_ir *)data;
- struct timeval tv;
- unsigned long current_jiffies, timeout;
- u32 gap;
-
- /* get time */
- current_jiffies = jiffies;
- do_gettimeofday(&tv);
-
- /* avoid overflow with gap >1s */
- if (tv.tv_sec - ir->base_time.tv_sec > 1) {
- gap = 200000;
- } else {
- gap = 1000000 * (tv.tv_sec - ir->base_time.tv_sec) +
- tv.tv_usec - ir->base_time.tv_usec;
- }
-
- /* Allow some timmer jitter (RC5 is ~24ms anyway so this is ok) */
- if (gap < 28000) {
- dprintk(KERN_WARNING "spurious timer_end\n");
- return;
- }
-
- ir->active = 0;
- if (ir->last_bit < 20) {
- /* ignore spurious codes (caused by light/other remotes) */
- dprintk(KERN_WARNING "short code: %x\n", ir->code);
- } else {
- u32 rc5 = rc5_decode(ir->code);
-
- /* two start bits? */
- if (RC5_START(rc5) != 3) {
- dprintk(KERN_WARNING "rc5 start bits invalid: %u\n", RC5_START(rc5));
-
- /* right address? */
- } else if (RC5_ADDR(rc5) == 0x0) {
- u32 toggle = RC5_TOGGLE(rc5);
- u32 instr = RC5_INSTR(rc5);
-
- /* Good code, decide if repeat/repress */
- if (toggle != RC5_TOGGLE(ir->last_rc5) ||
- instr != RC5_INSTR(ir->last_rc5)) {
- dprintk(KERN_WARNING "instruction %x, toggle %x\n", instr,
- toggle);
- ir_input_nokey(ir->dev, &ir->ir);
- ir_input_keydown(ir->dev, &ir->ir, instr,
- instr);
- }
-
- /* Set/reset key-up timer */
- timeout = current_jiffies + (500 + rc5_key_timeout
- * HZ) / 1000;
- mod_timer(&ir->timer_keyup, timeout);
-
- /* Save code for repeat test */
- ir->last_rc5 = rc5;
- }
- }
-}
-
-static void bttv_rc5_timer_keyup(unsigned long data)
-{
- struct bttv_ir *ir = (struct bttv_ir *)data;
-
- dprintk(KERN_DEBUG "key released\n");
- ir_input_nokey(ir->dev, &ir->ir);
-}
-
/* ---------------------------------------------------------------------- */
-static void bttv_ir_start(struct bttv *btv, struct bttv_ir *ir)
+static void bttv_ir_start(struct bttv *btv, struct card_ir *ir)
{
if (ir->polling) {
init_timer(&ir->timer);
} else if (ir->rc5_gpio) {
/* set timer_end for code completion */
init_timer(&ir->timer_end);
- ir->timer_end.function = bttv_rc5_timer_end;
+ ir->timer_end.function = ir_rc5_timer_end;
ir->timer_end.data = (unsigned long)ir;
init_timer(&ir->timer_keyup);
- ir->timer_keyup.function = bttv_rc5_timer_keyup;
+ ir->timer_keyup.function = ir_rc5_timer_keyup;
ir->timer_keyup.data = (unsigned long)ir;
+ ir->shift_by = 1;
+ ir->start = 3;
+ ir->addr = 0x0;
+ ir->rc5_key_timeout = ir_rc5_key_timeout;
+ ir->rc5_remote_gap = ir_rc5_remote_gap;
}
}
int bttv_input_init(struct bttv *btv)
{
- struct bttv_ir *ir;
+ struct card_ir *ir;
IR_KEYTAB_TYPE *ir_codes = NULL;
struct input_dev *input_dev;
int ir_type = IR_TYPE_OTHER;
struct bttv;
-struct bttv_ir {
- struct input_dev *dev;
- struct ir_input_state ir;
- char name[32];
- char phys[32];
-
- /* Usual gpio signalling */
-
- u32 mask_keycode;
- u32 mask_keydown;
- u32 mask_keyup;
- u32 polling;
- u32 last_gpio;
- struct work_struct work;
- struct timer_list timer;
-
- /* RC5 gpio */
- u32 rc5_gpio;
- struct timer_list timer_end; /* timer_end for code completion */
- struct timer_list timer_keyup; /* timer_end for key release */
- u32 last_rc5; /* last good rc5 code */
- u32 last_bit; /* last raw bit seen */
- u32 code; /* raw code under construction */
- struct timeval base_time; /* time of last seen code */
- int active; /* building raw code */
-};
-
struct tvcard
{
char *name;
/* infrared remote */
int has_remote;
- struct bttv_ir *remote;
+ struct card_ir *remote;
/* locking */
spinlock_t s_lock;
case SAA7134_BOARD_KWORLD_TERMINATOR:
case SAA7134_BOARD_SEDNA_PC_TV_CARDBUS:
case SAA7134_BOARD_FLYDVBT_LR301:
+ case SAA7134_BOARD_ASUSTeK_P7131_DUAL:
case SAA7134_BOARD_FLYDVBTDUO:
case SAA7134_BOARD_PROTEUS_2309:
case SAA7134_BOARD_AVERMEDIA_A16AR:
module_param(pinnacle_remote, int, 0644); /* Choose Pinnacle PCTV remote */
MODULE_PARM_DESC(pinnacle_remote, "Specify Pinnacle PCTV remote: 0=coloured, 1=grey (defaults to 0)");
+int ir_rc5_remote_gap = 885;
+module_param(ir_rc5_remote_gap, int, 0644);
+int ir_rc5_key_timeout = 115;
+module_param(ir_rc5_key_timeout, int, 0644);
+
#define dprintk(fmt, arg...) if (ir_debug) \
printk(KERN_DEBUG "%s/ir: " fmt, dev->name , ## arg)
#define i2cdprintk(fmt, arg...) if (ir_debug) \
printk(KERN_DEBUG "%s/ir: " fmt, ir->c.name , ## arg)
+/** rc5 functions */
+static int saa7134_rc5_irq(struct saa7134_dev *dev);
+
/* -------------------- GPIO generic keycode builder -------------------- */
static int build_key(struct saa7134_dev *dev)
{
- struct saa7134_ir *ir = dev->remote;
+ struct card_ir *ir = dev->remote;
u32 gpio, data;
/* rising SAA7134_GPIO_GPRESCAN reads the status */
void saa7134_input_irq(struct saa7134_dev *dev)
{
- struct saa7134_ir *ir = dev->remote;
+ struct card_ir *ir = dev->remote;
- if (!ir->polling)
+ if (!ir->polling && !ir->rc5_gpio) {
build_key(dev);
+ } else if (ir->rc5_gpio) {
+ saa7134_rc5_irq(dev);
+ }
}
static void saa7134_input_timer(unsigned long data)
{
struct saa7134_dev *dev = (struct saa7134_dev*)data;
- struct saa7134_ir *ir = dev->remote;
+ struct card_ir *ir = dev->remote;
unsigned long timeout;
build_key(dev);
mod_timer(&ir->timer, timeout);
}
-static void saa7134_ir_start(struct saa7134_dev *dev, struct saa7134_ir *ir)
+static void saa7134_ir_start(struct saa7134_dev *dev, struct card_ir *ir)
{
if (ir->polling) {
init_timer(&ir->timer);
ir->timer.data = (unsigned long)dev;
ir->timer.expires = jiffies + HZ;
add_timer(&ir->timer);
+ } else if (ir->rc5_gpio) {
+ /* set timer_end for code completion */
+ init_timer(&ir->timer_end);
+ ir->timer_end.function = ir_rc5_timer_end;
+ ir->timer_end.data = (unsigned long)ir;
+ init_timer(&ir->timer_keyup);
+ ir->timer_keyup.function = ir_rc5_timer_keyup;
+ ir->timer_keyup.data = (unsigned long)ir;
+ ir->shift_by = 2;
+ ir->start = 0x2;
+ ir->addr = 0x17;
+ ir->rc5_key_timeout = ir_rc5_key_timeout;
+ ir->rc5_remote_gap = ir_rc5_remote_gap;
}
}
int saa7134_input_init1(struct saa7134_dev *dev)
{
- struct saa7134_ir *ir;
+ struct card_ir *ir;
struct input_dev *input_dev;
IR_KEYTAB_TYPE *ir_codes = NULL;
u32 mask_keycode = 0;
u32 mask_keydown = 0;
u32 mask_keyup = 0;
int polling = 0;
+ int rc5_gpio = 0;
int ir_type = IR_TYPE_OTHER;
int err;
mask_keycode = 0x0001F00;
mask_keydown = 0x0040000;
break;
+ case SAA7134_BOARD_ASUSTeK_P7131_DUAL:
+ ir_codes = ir_codes_asus_pc39;
+ mask_keydown = 0x0040000;
+ rc5_gpio = 1;
+ break;
}
if (NULL == ir_codes) {
printk("%s: Oops: IR config error [card=%d]\n",
ir->mask_keydown = mask_keydown;
ir->mask_keyup = mask_keyup;
ir->polling = polling;
+ ir->rc5_gpio = rc5_gpio;
/* init input device */
snprintf(ir->name, sizeof(ir->name), "saa7134 IR (%s)",
}
}
+
+static int saa7134_rc5_irq(struct saa7134_dev *dev)
+{
+ struct card_ir *ir = dev->remote;
+ struct timeval tv;
+ u32 gap;
+ unsigned long current_jiffies, timeout;
+
+ /* get time of bit */
+ current_jiffies = jiffies;
+ do_gettimeofday(&tv);
+
+ /* avoid overflow with gap >1s */
+ if (tv.tv_sec - ir->base_time.tv_sec > 1) {
+ gap = 200000;
+ } else {
+ gap = 1000000 * (tv.tv_sec - ir->base_time.tv_sec) +
+ tv.tv_usec - ir->base_time.tv_usec;
+ }
+
+ /* active code => add bit */
+ if (ir->active) {
+ /* only if in the code (otherwise spurious IRQ or timer
+ late) */
+ if (ir->last_bit < 28) {
+ ir->last_bit = (gap - ir_rc5_remote_gap / 2) /
+ ir_rc5_remote_gap;
+ ir->code |= 1 << ir->last_bit;
+ }
+ /* starting new code */
+ } else {
+ ir->active = 1;
+ ir->code = 0;
+ ir->base_time = tv;
+ ir->last_bit = 0;
+
+ timeout = current_jiffies + (500 + 30 * HZ) / 1000;
+ mod_timer(&ir->timer_end, timeout);
+ }
+
+ return 1;
+}
+
/* ----------------------------------------------------------------------
* Local variables:
* c-basic-offset: 8
struct snd_pcm_substream *substream;
};
-/* IR input */
-struct saa7134_ir {
- struct input_dev *dev;
- struct ir_input_state ir;
- char name[32];
- char phys[32];
- u32 mask_keycode;
- u32 mask_keydown;
- u32 mask_keyup;
- int polling;
- u32 last_gpio;
- struct timer_list timer;
-};
-
/* ts/mpeg status */
struct saa7134_ts {
/* TS capture */
/* infrared remote */
int has_remote;
- struct saa7134_ir *remote;
+ struct card_ir *remote;
/* pci i/o */
char name[32];
void saa7134_input_irq(struct saa7134_dev *dev);
void saa7134_set_i2c_ir(struct saa7134_dev *dev, struct IR_i2c *ir);
+
/*
* Local variables:
* c-basic-offset: 8
#define IR_KEYCODE(tab,code) (((unsigned)code < IR_KEYTAB_SIZE) \
? tab[code] : KEY_RESERVED)
+extern int ir_rc5_remote_gap;
+extern int ir_rc5_key_timeout;
+
+#define RC5_START(x) (((x)>>12)&3)
+#define RC5_TOGGLE(x) (((x)>>11)&1)
+#define RC5_ADDR(x) (((x)>>6)&31)
+#define RC5_INSTR(x) ((x)&63)
+
struct ir_input_state {
/* configuration */
int ir_type;
int keypressed; /* current state */
};
+/* this was saa7134_ir and bttv_ir, moved here for
+ * rc5 decoding. */
+struct card_ir {
+ struct input_dev *dev;
+ struct ir_input_state ir;
+ char name[32];
+ char phys[32];
+
+ /* Usual gpio signalling */
+
+ u32 mask_keycode;
+ u32 mask_keydown;
+ u32 mask_keyup;
+ u32 polling;
+ u32 last_gpio;
+ int shift_by;
+ int start; // What should RC5_START() be
+ int addr; // What RC5_ADDR() should be.
+ int rc5_key_timeout;
+ int rc5_remote_gap;
+ struct work_struct work;
+ struct timer_list timer;
+
+ /* RC5 gpio */
+ u32 rc5_gpio;
+ struct timer_list timer_end; /* timer_end for code completion */
+ struct timer_list timer_keyup; /* timer_end for key release */
+ u32 last_rc5; /* last good rc5 code */
+ u32 last_bit; /* last raw bit seen */
+ u32 code; /* raw code under construction */
+ struct timeval base_time; /* time of last seen code */
+ int active; /* building raw code */
+};
+
void ir_input_init(struct input_dev *dev, struct ir_input_state *ir,
int ir_type, IR_KEYTAB_TYPE *ir_codes);
void ir_input_nokey(struct input_dev *dev, struct ir_input_state *ir);
int ir_decode_biphase(u32 *samples, int count, int low, int high);
int ir_decode_pulsedistance(u32 *samples, int count, int low, int high);
+u32 ir_rc5_decode(unsigned int code);
+void ir_rc5_timer_end(unsigned long data);
+void ir_rc5_timer_keyup(unsigned long data);
+
/* Keymaps to be used by other modules */
extern IR_KEYTAB_TYPE ir_codes_empty[IR_KEYTAB_SIZE];
extern IR_KEYTAB_TYPE ir_codes_norwood[IR_KEYTAB_SIZE];
extern IR_KEYTAB_TYPE ir_codes_proteus_2309[IR_KEYTAB_SIZE];
extern IR_KEYTAB_TYPE ir_codes_budget_ci_old[IR_KEYTAB_SIZE];
+extern IR_KEYTAB_TYPE ir_codes_asus_pc39[IR_KEYTAB_SIZE];
#endif
projects / linux-2.6 / commitdiff