config PCI_MMCONFIG
bool
depends on PCI && ACPI && (PCI_GOMMCONFIG || PCI_GOANY)
- select ACPI_BOOT
default y
source "drivers/pci/pcie/Kconfig"
# ACPI (Advanced Configuration and Power Interface) Support
#
CONFIG_ACPI=y
-CONFIG_ACPI_BOOT=y
CONFIG_ACPI_INTERPRETER=y
CONFIG_ACPI_SLEEP=y
CONFIG_ACPI_SLEEP_PROC_FS=y
obj-y += cpu/
obj-y += timers/
-obj-$(CONFIG_ACPI_BOOT) += acpi/
+obj-$(CONFIG_ACPI) += acpi/
obj-$(CONFIG_X86_BIOS_REBOOT) += reboot.o
obj-$(CONFIG_MCA) += mca.o
obj-$(CONFIG_X86_MSR) += msr.o
-obj-$(CONFIG_ACPI_BOOT) := boot.o
+obj-y := boot.o
obj-$(CONFIG_X86_IO_APIC) += earlyquirk.o
obj-$(CONFIG_ACPI_SLEEP) += sleep.o wakeup.o
ACPI-based IOAPIC Configuration
-------------------------------------------------------------------------- */
-#ifdef CONFIG_ACPI_BOOT
+#ifdef CONFIG_ACPI
int __init io_apic_get_unique_id (int ioapic, int apic_id)
{
return 0;
}
-#endif /*CONFIG_ACPI_BOOT*/
+#endif /* CONFIG_ACPI */
struct intel_mp_floating *mpf = mpf_found;
/*
- * ACPI may be used to obtain the entire SMP configuration or just to
- * enumerate/configure processors (CONFIG_ACPI_BOOT). Note that
* ACPI supports both logical (e.g. Hyper-Threading) and physical
* processors, where MPS only supports physical.
*/
ACPI-based MP Configuration
-------------------------------------------------------------------------- */
-#ifdef CONFIG_ACPI_BOOT
+#ifdef CONFIG_ACPI
void __init mp_register_lapic_address (
u64 address)
MP_processor_info(&processor);
}
-#if defined(CONFIG_X86_IO_APIC) && (defined(CONFIG_ACPI_INTERPRETER) || defined(CONFIG_ACPI_BOOT))
+#if defined(CONFIG_X86_IO_APIC) && defined(CONFIG_ACPI_INTERPRETER)
#define MP_ISA_BUS 0
#define MP_MAX_IOAPIC_PIN 127
return gsi;
}
-#endif /*CONFIG_X86_IO_APIC && (CONFIG_ACPI_INTERPRETER || CONFIG_ACPI_BOOT)*/
-#endif /*CONFIG_ACPI_BOOT*/
+#endif /* CONFIG_X86_IO_APIC && CONFIG_ACPI_INTERPRETER */
+#endif /* CONFIG_ACPI */
#endif
EXPORT_SYMBOL(acpi_disabled);
-#ifdef CONFIG_ACPI_BOOT
+#ifdef CONFIG_ACPI
int __initdata acpi_force = 0;
extern acpi_interrupt_flags acpi_sci_flags;
#endif
}
#endif
-#ifdef CONFIG_ACPI_BOOT
+#ifdef CONFIG_ACPI
/* "acpi=off" disables both ACPI table parsing and interpreter */
else if (!memcmp(from, "acpi=off", 8)) {
disable_acpi();
else if (!memcmp(from, "noapic", 6))
disable_ioapic_setup();
#endif /* CONFIG_X86_LOCAL_APIC */
-#endif /* CONFIG_ACPI_BOOT */
+#endif /* CONFIG_ACPI */
#ifdef CONFIG_X86_LOCAL_APIC
/* enable local APIC */
if (efi_enabled)
efi_map_memmap();
-#ifdef CONFIG_ACPI_BOOT
+#ifdef CONFIG_ACPI
/*
* Parse the ACPI tables for possible boot-time SMP configuration.
*/
int mip_port;
unsigned long mip_addr, host_addr;
-#if defined(CONFIG_X86_IO_APIC) && (defined(CONFIG_ACPI_INTERPRETER) || defined(CONFIG_ACPI_BOOT))
+#if defined(CONFIG_X86_IO_APIC) && defined(CONFIG_ACPI_INTERPRETER)
/*
* GSI override for ES7000 platforms.
return gsi;
}
-#endif // (CONFIG_X86_IO_APIC) && (CONFIG_ACPI_INTERPRETER || CONFIG_ACPI_BOOT)
+#endif // (CONFIG_X86_IO_APIC) && (CONFIG_ACPI_INTERPRETER)
/*
* Parse the OEM Table
#
# ACPI (Advanced Configuration and Power Interface) Support
#
-CONFIG_ACPI_BOOT=y
CONFIG_ACPI_INTERPRETER=y
CONFIG_ACPI_BUTTON=m
CONFIG_ACPI_VIDEO=m
#
# ACPI (Advanced Configuration and Power Interface) Support
#
-CONFIG_ACPI_BOOT=y
CONFIG_ACPI_INTERPRETER=y
# CONFIG_ACPI_BUTTON is not set
CONFIG_ACPI_VIDEO=m
#
# ACPI (Advanced Configuration and Power Interface) Support
#
-CONFIG_ACPI_BOOT=y
CONFIG_ACPI_INTERPRETER=y
CONFIG_ACPI_BUTTON=m
# CONFIG_ACPI_VIDEO is not set
#
# ACPI (Advanced Configuration and Power Interface) Support
#
-CONFIG_ACPI_BOOT=y
CONFIG_ACPI_INTERPRETER=y
CONFIG_ACPI_BUTTON=y
CONFIG_ACPI_VIDEO=m
#
# ACPI (Advanced Configuration and Power Interface) Support
#
-CONFIG_ACPI_BOOT=y
CONFIG_ACPI_INTERPRETER=y
CONFIG_ACPI_BUTTON=m
CONFIG_ACPI_VIDEO=m
#endif
}
-#ifdef CONFIG_ACPI_BOOT
+#ifdef CONFIG_ACPI
#define ACPI_MAX_PLATFORM_INTERRUPTS 256
EXPORT_SYMBOL(acpi_unregister_ioapic);
-#endif /* CONFIG_ACPI_BOOT */
+#endif /* CONFIG_ACPI */
if (early_console_setup(*cmdline_p) == 0)
mark_bsp_online();
-#ifdef CONFIG_ACPI_BOOT
+#ifdef CONFIG_ACPI
/* Initialize the ACPI boot-time table parser */
acpi_table_init();
# ifdef CONFIG_ACPI_NUMA
cpu_init(); /* initialize the bootstrap CPU */
-#ifdef CONFIG_ACPI_BOOT
+#ifdef CONFIG_ACPI
acpi_boot_init();
#endif
parent = &sysfs_nodes[cpu_to_node(num)];
#endif /* CONFIG_NUMA */
-#ifdef CONFIG_ACPI_BOOT
+#ifdef CONFIG_ACPI
/*
* If CPEI cannot be re-targetted, and this is
* CPEI target, then dont create the control file
with major 203 and minors 0 to 31 for /dev/cpu/0/cpuid to
/dev/cpu/31/cpuid.
-# disable it for opteron optimized builds because it pulls in ACPI_BOOT
config X86_HT
bool
depends on SMP && !MK8
config PCI_MMCONFIG
bool "Support mmconfig PCI config space access"
depends on PCI && ACPI
- select ACPI_BOOT
config UNORDERED_IO
bool "Unordered IO mapping access"
# ACPI (Advanced Configuration and Power Interface) Support
#
CONFIG_ACPI=y
-CONFIG_ACPI_BOOT=y
CONFIG_ACPI_INTERPRETER=y
CONFIG_ACPI_AC=y
CONFIG_ACPI_BATTERY=y
obj-$(CONFIG_X86_MCE) += mce.o
obj-$(CONFIG_X86_MCE_INTEL) += mce_intel.o
obj-$(CONFIG_MTRR) += ../../i386/kernel/cpu/mtrr/
-obj-$(CONFIG_ACPI_BOOT) += acpi/
+obj-$(CONFIG_ACPI) += acpi/
obj-$(CONFIG_X86_MSR) += msr.o
obj-$(CONFIG_MICROCODE) += microcode.o
obj-$(CONFIG_X86_CPUID) += cpuid.o
-obj-$(CONFIG_ACPI_BOOT) := boot.o
-boot-$(CONFIG_ACPI_BOOT) := ../../../i386/kernel/acpi/boot.o
+obj-y := boot.o
+boot-y := ../../../i386/kernel/acpi/boot.o
obj-$(CONFIG_ACPI_SLEEP) += sleep.o wakeup.o
ACPI-based IOAPIC Configuration
-------------------------------------------------------------------------- */
-#ifdef CONFIG_ACPI_BOOT
+#ifdef CONFIG_ACPI
#define IO_APIC_MAX_ID 0xFE
return 0;
}
-#endif /*CONFIG_ACPI_BOOT*/
+#endif /* CONFIG_ACPI */
/*
physid_mask_t phys_cpu_present_map = PHYSID_MASK_NONE;
/* ACPI MADT entry parsing functions */
-#ifdef CONFIG_ACPI_BOOT
+#ifdef CONFIG_ACPI
extern struct acpi_boot_flags acpi_boot;
#ifdef CONFIG_X86_LOCAL_APIC
extern int acpi_parse_lapic (acpi_table_entry_header *header);
#ifdef CONFIG_X86_IO_APIC
extern int acpi_parse_ioapic (acpi_table_entry_header *header);
#endif /*CONFIG_X86_IO_APIC*/
-#endif /*CONFIG_ACPI_BOOT*/
+#endif /*CONFIG_ACPI*/
u8 bios_cpu_apicid[NR_CPUS] = { [0 ... NR_CPUS-1] = BAD_APICID };
struct intel_mp_floating *mpf = mpf_found;
/*
- * ACPI may be used to obtain the entire SMP configuration or just to
- * enumerate/configure processors (CONFIG_ACPI_BOOT). Note that
* ACPI supports both logical (e.g. Hyper-Threading) and physical
* processors, where MPS only supports physical.
*/
ACPI-based MP Configuration
-------------------------------------------------------------------------- */
-#ifdef CONFIG_ACPI_BOOT
+#ifdef CONFIG_ACPI
void __init mp_register_lapic_address (
u64 address)
}
#endif /*CONFIG_X86_IO_APIC*/
-#endif /*CONFIG_ACPI_BOOT*/
+#endif /*CONFIG_ACPI*/
int acpi_disabled;
EXPORT_SYMBOL(acpi_disabled);
-#ifdef CONFIG_ACPI_BOOT
+#ifdef CONFIG_ACPI
extern int __initdata acpi_ht;
extern acpi_interrupt_flags acpi_sci_flags;
int __initdata acpi_force = 0;
maxcpus = simple_strtoul(from + 8, NULL, 0);
}
#endif
-#ifdef CONFIG_ACPI_BOOT
+#ifdef CONFIG_ACPI
/* "acpi=off" disables both ACPI table parsing and interpreter init */
if (!memcmp(from, "acpi=off", 8))
disable_acpi();
init_memory_mapping(0, (end_pfn_map << PAGE_SHIFT));
-#ifdef CONFIG_ACPI_BOOT
+#ifdef CONFIG_ACPI
/*
* Initialize the ACPI boot-time table parser (gets the RSDP and SDT).
* Call this early for SRAT node setup.
check_ioapic();
-#ifdef CONFIG_ACPI_BOOT
+#ifdef CONFIG_ACPI
/*
* Read APIC and some other early information from ACPI tables.
*/
obj-$(CONFIG_PCI) += pci/
obj-$(CONFIG_PARISC) += parisc/
obj-y += video/
-obj-$(CONFIG_ACPI_BOOT) += acpi/
+obj-$(CONFIG_ACPI) += acpi/
# PnP must come after ACPI since it will eventually need to check if acpi
# was used and do nothing if so
obj-$(CONFIG_PNP) += pnp/
if ACPI
-config ACPI_BOOT
- bool
- default y
-
config ACPI_INTERPRETER
bool
default y
config X86_PM_TIMER
bool "Power Management Timer Support"
depends on X86
- depends on ACPI_BOOT && EXPERIMENTAL
+ depends on EXPERIMENTAL
depends on !X86_64
default n
help
#
# ACPI Boot-Time Table Parsing
#
-obj-$(CONFIG_ACPI_BOOT) += tables.o
+obj-y += tables.o
obj-$(CONFIG_ACPI_INTERPRETER) += blacklist.o
#
:"=r"(n_hi), "=r"(n_lo) \
:"0"(n_hi), "1"(n_lo))
-#ifdef CONFIG_ACPI_BOOT
+#ifdef CONFIG_ACPI
extern int acpi_lapic;
extern int acpi_ioapic;
extern int acpi_noirq;
#endif
-#else /* CONFIG_ACPI_BOOT */
+#else /* !CONFIG_ACPI */
# define acpi_lapic 0
# define acpi_ioapic 0
FIX_KMAP_BEGIN, /* reserved pte's for temporary kernel mappings */
FIX_KMAP_END = FIX_KMAP_BEGIN+(KM_TYPE_NR*NR_CPUS)-1,
#endif
-#ifdef CONFIG_ACPI_BOOT
+#ifdef CONFIG_ACPI
FIX_ACPI_BEGIN,
FIX_ACPI_END = FIX_ACPI_BEGIN + FIX_ACPI_PAGES - 1,
#endif
*/
#define io_apic_assign_pci_irqs (mp_irq_entries && !skip_ioapic_setup && io_apic_irqs)
-#ifdef CONFIG_ACPI_BOOT
+#ifdef CONFIG_ACPI
extern int io_apic_get_unique_id (int ioapic, int apic_id);
extern int io_apic_get_version (int ioapic);
extern int io_apic_get_redir_entries (int ioapic);
extern int io_apic_set_pci_routing (int ioapic, int pin, int irq, int edge_level, int active_high_low);
-#endif /*CONFIG_ACPI_BOOT*/
+#endif /* CONFIG_ACPI */
extern int (*ioapic_renumber_irq)(int ioapic, int irq);
extern int pic_mode;
extern int using_apic_timer;
-#ifdef CONFIG_ACPI_BOOT
+#ifdef CONFIG_ACPI
extern void mp_register_lapic (u8 id, u8 enabled);
extern void mp_register_lapic_address (u64 address);
extern void mp_register_ioapic (u8 id, u32 address, u32 gsi_base);
extern void mp_override_legacy_irq (u8 bus_irq, u8 polarity, u8 trigger, u32 gsi);
extern void mp_config_acpi_legacy_irqs (void);
extern int mp_register_gsi (u32 gsi, int edge_level, int active_high_low);
-#endif /*CONFIG_ACPI_BOOT*/
+#endif /* CONFIG_ACPI */
#define PHYSID_ARRAY_SIZE BITS_TO_LONGS(MAX_APICS)
:"=r"(n_hi), "=r"(n_lo) \
:"0"(n_hi), "1"(n_lo))
-#ifdef CONFIG_ACPI_BOOT
+#ifdef CONFIG_ACPI
extern int acpi_lapic;
extern int acpi_ioapic;
extern int acpi_noirq;
extern int acpi_gsi_to_irq(u32 gsi, unsigned int *irq);
-#else /* !CONFIG_ACPI_BOOT */
+#else /* !CONFIG_ACPI */
#define acpi_lapic 0
#define acpi_ioapic 0
-#endif /* !CONFIG_ACPI_BOOT */
+#endif /* !CONFIG_ACPI */
extern int acpi_numa;
extern int acpi_scan_nodes(unsigned long start, unsigned long end);
*/
#define io_apic_assign_pci_irqs (mp_irq_entries && !skip_ioapic_setup && io_apic_irqs)
-#ifdef CONFIG_ACPI_BOOT
+#ifdef CONFIG_ACPI
extern int io_apic_get_version (int ioapic);
extern int io_apic_get_redir_entries (int ioapic);
extern int io_apic_set_pci_routing (int ioapic, int pin, int irq, int, int);
extern unsigned long mp_lapic_addr;
extern int pic_mode;
-#ifdef CONFIG_ACPI_BOOT
+#ifdef CONFIG_ACPI
extern void mp_register_lapic (u8 id, u8 enabled);
extern void mp_register_lapic_address (u64 address);
#include <asm/acpi.h>
-#ifdef CONFIG_ACPI_BOOT
+#ifdef CONFIG_ACPI
enum acpi_irq_model_id {
ACPI_IRQ_MODEL_PIC = 0,
extern int sbf_port ;
-#else /*!CONFIG_ACPI_BOOT*/
+#else /* !CONFIG_ACPI */
#define acpi_mp_config 0
-#endif /*!CONFIG_ACPI_BOOT*/
+#endif /* !CONFIG_ACPI */
int acpi_register_gsi (u32 gsi, int edge_level, int active_high_low);
int acpi_gsi_to_irq (u32 gsi, unsigned int *irq);