--- /dev/null
+/*
+ * arch/arch/mach-ixp4xx/fsg-pci.c
+ *
+ * FSG board-level PCI initialization
+ *
+ * Author: Rod Whitby <rod@whitby.id.au>
+ * Maintainer: http://www.nslu2-linux.org/
+ *
+ * based on ixdp425-pci.c:
+ * Copyright (C) 2002 Intel Corporation.
+ * Copyright (C) 2003-2004 MontaVista Software, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/irq.h>
+
+#include <asm/mach/pci.h>
+#include <asm/mach-types.h>
+
+void __init fsg_pci_preinit(void)
+{
+ set_irq_type(IRQ_FSG_PCI_INTA, IRQT_LOW);
+ set_irq_type(IRQ_FSG_PCI_INTB, IRQT_LOW);
+ set_irq_type(IRQ_FSG_PCI_INTC, IRQT_LOW);
+
+ ixp4xx_pci_preinit();
+}
+
+static int __init fsg_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
+{
+ static int pci_irq_table[FSG_PCI_IRQ_LINES] = {
+ IRQ_FSG_PCI_INTC,
+ IRQ_FSG_PCI_INTB,
+ IRQ_FSG_PCI_INTA,
+ };
+
+ int irq = -1;
+ slot = slot - 11;
+
+ if (slot >= 1 && slot <= FSG_PCI_MAX_DEV &&
+ pin >= 1 && pin <= FSG_PCI_IRQ_LINES)
+ irq = pci_irq_table[(slot - 1)];
+ printk(KERN_INFO "%s: Mapped slot %d pin %d to IRQ %d\n",
+ __func__, slot, pin, irq);
+
+ return irq;
+}
+
+struct hw_pci fsg_pci __initdata = {
+ .nr_controllers = 1,
+ .preinit = fsg_pci_preinit,
+ .swizzle = pci_std_swizzle,
+ .setup = ixp4xx_setup,
+ .scan = ixp4xx_scan_bus,
+ .map_irq = fsg_map_irq,
+};
+
+int __init fsg_pci_init(void)
+{
+ if (machine_is_fsg())
+ pci_common_init(&fsg_pci);
+ return 0;
+}
+
+subsys_initcall(fsg_pci_init);
--- /dev/null
+/*
+ * arch/arm/mach-ixp4xx/fsg-setup.c
+ *
+ * FSG board-setup
+ *
+ * Copyright (C) 2008 Rod Whitby <rod@whitby.id.au>
+ *
+ * based on ixdp425-setup.c:
+ * Copyright (C) 2003-2004 MontaVista Software, Inc.
+ * based on nslu2-power.c
+ * Copyright (C) 2005 Tower Technologies
+ *
+ * Author: Rod Whitby <rod@whitby.id.au>
+ * Maintainers: http://www.nslu2-linux.org/
+ *
+ */
+
+#include <linux/if_ether.h>
+#include <linux/irq.h>
+#include <linux/serial.h>
+#include <linux/serial_8250.h>
+#include <linux/leds.h>
+#include <linux/reboot.h>
+#include <linux/i2c.h>
+#include <linux/i2c-gpio.h>
+
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/flash.h>
+#include <asm/io.h>
+#include <asm/gpio.h>
+
+static struct flash_platform_data fsg_flash_data = {
+ .map_name = "cfi_probe",
+ .width = 2,
+};
+
+static struct resource fsg_flash_resource = {
+ .flags = IORESOURCE_MEM,
+};
+
+static struct platform_device fsg_flash = {
+ .name = "IXP4XX-Flash",
+ .id = 0,
+ .dev = {
+ .platform_data = &fsg_flash_data,
+ },
+ .num_resources = 1,
+ .resource = &fsg_flash_resource,
+};
+
+static struct i2c_gpio_platform_data fsg_i2c_gpio_data = {
+ .sda_pin = FSG_SDA_PIN,
+ .scl_pin = FSG_SCL_PIN,
+};
+
+static struct platform_device fsg_i2c_gpio = {
+ .name = "i2c-gpio",
+ .id = 0,
+ .dev = {
+ .platform_data = &fsg_i2c_gpio_data,
+ },
+};
+
+static struct i2c_board_info __initdata fsg_i2c_board_info [] = {
+ {
+ I2C_BOARD_INFO("rtc-isl1208", 0x6f),
+ },
+};
+
+static struct resource fsg_uart_resources[] = {
+ {
+ .start = IXP4XX_UART1_BASE_PHYS,
+ .end = IXP4XX_UART1_BASE_PHYS + 0x0fff,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = IXP4XX_UART2_BASE_PHYS,
+ .end = IXP4XX_UART2_BASE_PHYS + 0x0fff,
+ .flags = IORESOURCE_MEM,
+ }
+};
+
+static struct plat_serial8250_port fsg_uart_data[] = {
+ {
+ .mapbase = IXP4XX_UART1_BASE_PHYS,
+ .membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
+ .irq = IRQ_IXP4XX_UART1,
+ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+ .iotype = UPIO_MEM,
+ .regshift = 2,
+ .uartclk = IXP4XX_UART_XTAL,
+ },
+ {
+ .mapbase = IXP4XX_UART2_BASE_PHYS,
+ .membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
+ .irq = IRQ_IXP4XX_UART2,
+ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+ .iotype = UPIO_MEM,
+ .regshift = 2,
+ .uartclk = IXP4XX_UART_XTAL,
+ },
+ { }
+};
+
+static struct platform_device fsg_uart = {
+ .name = "serial8250",
+ .id = PLAT8250_DEV_PLATFORM,
+ .dev = {
+ .platform_data = fsg_uart_data,
+ },
+ .num_resources = ARRAY_SIZE(fsg_uart_resources),
+ .resource = fsg_uart_resources,
+};
+
+static struct platform_device fsg_leds = {
+ .name = "fsg-led",
+ .id = -1,
+};
+
+/* Built-in 10/100 Ethernet MAC interfaces */
+static struct eth_plat_info fsg_plat_eth[] = {
+ {
+ .phy = 5,
+ .rxq = 3,
+ .txreadyq = 20,
+ }, {
+ .phy = 4,
+ .rxq = 4,
+ .txreadyq = 21,
+ }
+};
+
+static struct platform_device fsg_eth[] = {
+ {
+ .name = "ixp4xx_eth",
+ .id = IXP4XX_ETH_NPEB,
+ .dev = {
+ .platform_data = fsg_plat_eth,
+ },
+ }, {
+ .name = "ixp4xx_eth",
+ .id = IXP4XX_ETH_NPEC,
+ .dev = {
+ .platform_data = fsg_plat_eth + 1,
+ },
+ }
+};
+
+static struct platform_device *fsg_devices[] __initdata = {
+ &fsg_i2c_gpio,
+ &fsg_flash,
+ &fsg_leds,
+ &fsg_eth[0],
+ &fsg_eth[1],
+};
+
+static irqreturn_t fsg_power_handler(int irq, void *dev_id)
+{
+ /* Signal init to do the ctrlaltdel action, this will bypass init if
+ * it hasn't started and do a kernel_restart.
+ */
+ ctrl_alt_del();
+
+ return IRQ_HANDLED;
+}
+
+static irqreturn_t fsg_reset_handler(int irq, void *dev_id)
+{
+ /* This is the paper-clip reset which does an emergency reboot. */
+ printk(KERN_INFO "Restarting system.\n");
+ machine_restart(NULL);
+
+ /* This should never be reached. */
+ return IRQ_HANDLED;
+}
+
+static void __init fsg_init(void)
+{
+ DECLARE_MAC_BUF(mac_buf);
+ uint8_t __iomem *f;
+ int i;
+
+ ixp4xx_sys_init();
+
+ fsg_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
+ fsg_flash_resource.end =
+ IXP4XX_EXP_BUS_BASE(0) + ixp4xx_exp_bus_size - 1;
+
+ *IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE;
+ *IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0;
+
+ /* Configure CS2 for operation, 8bit and writable */
+ *IXP4XX_EXP_CS2 = 0xbfff0002;
+
+ i2c_register_board_info(0, fsg_i2c_board_info,
+ ARRAY_SIZE(fsg_i2c_board_info));
+
+ /* This is only useful on a modified machine, but it is valuable
+ * to have it first in order to see debug messages, and so that
+ * it does *not* get removed if platform_add_devices fails!
+ */
+ (void)platform_device_register(&fsg_uart);
+
+ platform_add_devices(fsg_devices, ARRAY_SIZE(fsg_devices));
+
+ if (request_irq(gpio_to_irq(FSG_RB_GPIO), &fsg_reset_handler,
+ IRQF_DISABLED | IRQF_TRIGGER_LOW,
+ "FSG reset button", NULL) < 0) {
+
+ printk(KERN_DEBUG "Reset Button IRQ %d not available\n",
+ gpio_to_irq(FSG_RB_GPIO));
+ }
+
+ if (request_irq(gpio_to_irq(FSG_SB_GPIO), &fsg_power_handler,
+ IRQF_DISABLED | IRQF_TRIGGER_LOW,
+ "FSG power button", NULL) < 0) {
+
+ printk(KERN_DEBUG "Power Button IRQ %d not available\n",
+ gpio_to_irq(FSG_SB_GPIO));
+ }
+
+ /*
+ * Map in a portion of the flash and read the MAC addresses.
+ * Since it is stored in BE in the flash itself, we need to
+ * byteswap it if we're in LE mode.
+ */
+ f = ioremap(IXP4XX_EXP_BUS_BASE(0), 0x400000);
+ if (f) {
+#ifdef __ARMEB__
+ for (i = 0; i < 6; i++) {
+ fsg_plat_eth[0].hwaddr[i] = readb(f + 0x3C0422 + i);
+ fsg_plat_eth[1].hwaddr[i] = readb(f + 0x3C043B + i);
+ }
+#else
+
+ /*
+ Endian-swapped reads from unaligned addresses are
+ required to extract the two MACs from the big-endian
+ Redboot config area in flash.
+ */
+
+ fsg_plat_eth[0].hwaddr[0] = readb(f + 0x3C0421);
+ fsg_plat_eth[0].hwaddr[1] = readb(f + 0x3C0420);
+ fsg_plat_eth[0].hwaddr[2] = readb(f + 0x3C0427);
+ fsg_plat_eth[0].hwaddr[3] = readb(f + 0x3C0426);
+ fsg_plat_eth[0].hwaddr[4] = readb(f + 0x3C0425);
+ fsg_plat_eth[0].hwaddr[5] = readb(f + 0x3C0424);
+
+ fsg_plat_eth[1].hwaddr[0] = readb(f + 0x3C0439);
+ fsg_plat_eth[1].hwaddr[1] = readb(f + 0x3C043F);
+ fsg_plat_eth[1].hwaddr[2] = readb(f + 0x3C043E);
+ fsg_plat_eth[1].hwaddr[3] = readb(f + 0x3C043D);
+ fsg_plat_eth[1].hwaddr[4] = readb(f + 0x3C043C);
+ fsg_plat_eth[1].hwaddr[5] = readb(f + 0x3C0443);
+#endif
+ iounmap(f);
+ }
+ printk(KERN_INFO "FSG: Using MAC address %s for port 0\n",
+ print_mac(mac_buf, fsg_plat_eth[0].hwaddr));
+ printk(KERN_INFO "FSG: Using MAC address %s for port 1\n",
+ print_mac(mac_buf, fsg_plat_eth[1].hwaddr));
+
+}
+
+MACHINE_START(FSG, "Freecom FSG-3")
+ /* Maintainer: www.nslu2-linux.org */
+ .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS,
+ .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
+ .map_io = ixp4xx_map_io,
+ .init_irq = ixp4xx_init_irq,
+ .timer = &ixp4xx_timer,
+ .boot_params = 0x0100,
+ .init_machine = fsg_init,
+MACHINE_END
+
projects / linux-2.6 / commitdiff